Pulsar Accolade LRF XQ38 Руководство пользователя

Бренд: Pulsar

Модель: Accolade LRF XQ38

Тип: Руководство пользователя

Это руководство также подходит для

Accolade LRF XP50

www.pulsar-nv.com

ACCOLADE LRF

Thermal Imaging Binoculars

Electromagnetic compliance

This product complies with EU Standard EN 55032:2015,

Class A.

Warning! Operation of this equipment in a residential

environment could cause radio interference.

Электромагнитная совместимость.

Данный продукт соответствует требованиям

европейского стандарта EN 55032:2015, Класс А.

Внимание: эксплуатация данного продукта в жилой зоне

может создавать радиопомехи.

Attention! Accolade LRF thermal imaging binoculars

require a license if exported outside your country.

Внимание!

Тепловизионные бинокли Accolade LRF требуют

лицензии, если они экспортируются за пределы

Вашей страны.

v.0518

LRF Laser Aperture

1-30

31-62

РУССКИЙ

Thermal Imaging Binoculars Accolade LRF

Тепловизионные бинокли Accolade LRF

Microbolometer:

MODEL ACCOLADE LRF

XQ38

77415

SKU#

Optical characteristics:

Operational characteristics:

384x288

3.1

3.1-12.4

1:1.2

9.8 / 17.2

1350 / 1475

AMOLED

640x480

3.7V

IPХ7

-25 °С ... +50 °С / -13 °F ... 122 °F

164x130x64 /

6.4x5.1x2.5

164x130x64 /

6.4x5.1x2.5

0.6 / 21.2

XP50

77418

640x480

2.5

2.5-20

12.4 / 21.8

±5

1800 / 1970

AMOLED

640x480

IPХ7

1:1.2

x2/x4

±5

x2/x4/x8

56-71 56-71

3.7V

5V 5V

Accolade LRF thermal imaging binoculars are based on an IR sensor

(uncooled microbolometer) are represented by a number of models

featuring various magnification and lens diameter. The binoculars

feature comfortable observation with both eyes.

The binoculars are equipped with a precise built-in laser rangefinder

designed to measure distance up to 1km.

The binoculars are designed for the use both in the night-time and during

the day in adverse weather conditions (fog, smog, rain) to see through

obstacles hindering detection of targets (branches, tallgrass, thick

bushes etc.). The binoculars do not require an external source of light

and are not affected by bright light exposure.

Accolade LRF thermal imaging binoculars are designed for various

areas of application including night hunting, observation, trail

orienteering, rescue operations etc.

Built-in precise laser rangefinder (up to 1000m)

Comfortable for long observation

Variable interpupillary distance

High refresh rate 50 Hz

Built-in video recorder

Built-in Wi-Fi module

Wi-Fi video transmission

Live internet video sharing

Frost resistant AMOLED display

Quick-change long-life rechargeable Battery Packs

Fully waterproof IPX7

uncooled

Li-Ion Battery Pack IPS5 / 5000 mAh /

DC 3.7V

8 Gb

150 min video or ˃10 000 pictures

8 Gb

2.4GHz

Type

Resolution, pixels

Frame rate, Hz

Pixel size, µm

Magnification, x

Continuous digital zoom, x

Digital zoom

Objective lens

Close-up range, m

Exit pupil diameter, mm

Field of view (HxV), degrees / m@100m

Dioptre adjustment, D

Max. observation range of

an animal, such as deer, m/y, approx.

Display:

Type

Resolution, pixels

Power supply

Battery type / Capacity /

Output voltage

External power supply

Operating time on

Battery Pack (at t=22°C), h*

Degree of protection, IP code

(IEC60529)

Operating temperature range

Dimensions, mm / inch

Weight (without battery), kg / oz

Video recorder

Video / photo resolution, pixel

Video / photo format

Built-in memory

Built-in memory capacity

Wi-Fi channel

Frequency

Standard

Line-of-sight reception range, m

uncooled

640x480

.avi / .jpg

640x480

.avi / .jpg

Interpupillary distance adjustment, mm

PACKAGE CONTENTS

Accolade LRF Thermal Imaging

Binoculars

Carrying case

IPS5 Battery Pack

Battery charger with mains

charger

Micro USB cable

Neck strap

User manual

Lens cloth

Warranty card

This product is subject to change in line with improvements to its design.

The latest edition of this user manual is available online at www.pulsar-nv.com

DESCRIPTION

FEATURES

Major features:

0.6 / 21.2

802,11 b/g/n

905

1000 / 1094

+/-1

Characteristics of the rangefinder

Max. measuring range, m/y**

Measurement accuracy, m

Wavelength, nm

905

1000 / 1094

+/-1

** Depends on the characteristics of the object under observation and environmental conditions.

* Actual operating time depends on the extent of using Wi-Fi, integrated video recorder and

integrated laser rangefinder.

Safety class for laser equipment

according to IEC 60825-1:2014

“Picture-in-Picture” mode

Color palettes

Observation modes

Calibration modes

Manual contrast and brightness adjustment

Power ON/OFF / Calibration button

Navigation button UP

Button MENU

Recording button REC

Navigation button DOWN

Interpupillary distance adjustment rings

Dioptre adjustment rings

Lens focusing ring

Battery Pack

Battery Pack latch

Tripod mount

Radiator cooling system

Lens cover

Objective lens

MicroUSB port

MicroUSB cable

Integrated laser rangefinder

Extra features:

EXTERNAL VIEW AND CONTROLS

Pic. 1

FUNCTIONS OF CONTROL BUTTONS

Device is off

OTHER SHORT

PRESSES

LONG PRESS

Turn display off/

Power device off

CURRENT

OPERATING MODE

FIRST SHORT

PRESS

Power device on

Calibrate the sensor

Display OFF

mode

Turn display on

Calibrate the sensor

Device is on

Calibrate the sensor

Regular

navigation

Navigation upwards/rightwards

Switch between

colour palettes

Regular

navigation

Enter quick menu

Switch between

quick menu options

Confirm selection

Enter main menu

Control incremental digital zoom

PiP on/off

Navigation downwards/leftwards

Video

Start video

recording

Pause / resume

video recording

Stop video recording /

Switch to photo mode

Photo Take a photograph

Switch to video mode

BUTTON

ON/OFF

(1)

UP (2)

MENU (3)

DOWN

(5)

REC (4)

Rangefinder

----

Activate rangefinder

Measure distance

Start/stop

SCAN mode

----

Accolade LRF thermal imaging binoculars are supplied with a

rechargeable Li-Ion Battery Pack IPS5 which allows operation for up to

7 hours. Please remember to charge the Battery Pack before first use.

Charging:

USING THE BATTERY PACK

Lift the lever (C) of the charging base.

Remove the protective cover from the Battery Pack.

Install the Battery Pack into the charging base as shown in Pic.2;

click the lever (C).

Upon installation, a green LED indicator (D) on the charging base

will start to glow and begin flashing:

- once if the battery charge ranges from 0% to 50%;

- twice if the battery charge ranges from 51% to 75%;

- three times if the battery charge ranges from 76% to 100%;

If the indicator lights green continuously, the battery is fully charged.

You can remove the battery from the charger by lifting the lever (10).

If the indicator of the charger lights red continuously upon battery

installation, probably the battery's charge level is lower than

acceptable (the battery has been long in deep discharge).

Keep the battery in the charger for a long time (up to several hours),

remove and re-insert it. If the indicator starts blinking green, the

battery is good; if it keeps lighting red it's defective.

Do not use the battery!

Connect the Micro-USB plug of the USB cable to the port (E) of the

charger.

Connect the Micro-USB plug to the charger.

Insert the plug of the charger to the 220V socket.

Lift the lever (10).

Install the battery (9) all the

way into the dedicated slot on

the device housing so that

element F appears from below

(Pic.3) .

Fix the battery by clicking the

lever.

Installing the Battery Pack:

Only use the charger supplied with your binoculars.

When keeping the battery for a long period, the battery should

not be fully charged or fully discharged.

Do not charge the battery immediately after bringing the

battery from cold environment to a warm one. Wait for 30-40

minutes for the battery to get warm.

Charge the Battery Pack at a temperature from 0 °C to +45 °C.

Otherwise batter's life will decrease significantly.

Do not leave a battery unattended while charging.

Safety measures:

Charging

base

Battery Pack

Charger

220V socket

109

Pic. 3

Pic. 2

The device can be powered with an external power supply such as

Power Bank (5V).

Connect the external power supply to the USB port (15) of the device

(Pic. 1).

The device switches to operation from external power supply, and the

IPS5 Battery Pack will begin slowly charging.

The display will show the battery icon with charge level as a

percentage.

If the device operates on external power supply but the IPS5 battery is

not connected, icon is shown.

When the external power supply is disconnected, the device switches

to the internal battery pack without powering off.

Never use a modified or damaged charger.

Do not leave the Battery Pack with a charger connected to the

mains longer than 24 hours after full charge.

Do not expose the battery pack to high temperature or to a naked

flame.

Do not submerge the battery in water.

Do not connect external device with a current consumption that

exceeds permitted levels.

The Battery Pack is short circuit protected. However, any situation

that may cause short-circuiting should be avoided.

Do not dismantle or deform the Battery Pack.

Do not drop or hit the battery.

When using the battery at negative temperatures, battery's capacity

decreases, this is normal and is not a defect.

Do not use the battery at the temperatures above those shown in

the table – this may decrease battery's life.

Keep the battery out of the reach of children.

EXTERNAL POWER SUPPLY

WARNING!

Do not point the objective lens of the device at intensive sources

of light such device emitting laser radiation or the sun. This may

render the electronic components inoperative. The warranty does

not cover damage caused by improper operation.

WARNING!

The radiator cooling system (12) becomes warm during operation:

this is normal and allows an increase in the sensitivity of the

device.

Powering on and image setup

Open the lens cover .(13)

T device ON/OFF (1) urn the on with a short press of the button.

Adjust the interpupillary distance with the rings (6) by moving the

eyepieces farther or closer to each other.

To obtain a crisp image of the icons on the display, rotate the dioptre

adjustment ring . there is no need to rotate the s (7) Once adjusted,

dioptre adjustment ring for distance or any other conditions.

To focus on the object being observed rotate the lens focusing

ring .(8)

To set up display brightness and contrast and continuous zoom,

please refer to the MENU FUNCTIONS section. QUICK

A press and ON/OFF devicefter use, hold down the button to turn the

off.

Calibration allows levelling of the background temperature of the

microbolometer and eliminates image flaws (such as frozen image,

vertical stripes etc.).

There are three calibration modes:

manual (M), semi-automatic (SA) and automatic (А).

OPERATION

SENSOR CALIBRATION

Mode М (manual)

- Close the lens cover, press briefly the ON/OFF (1) button.

- Open the lens cover.

Mode SA (semi-automatic)

- Press briefly the ON/OFF button to calibrate.

- You do not need to close the lens cover (the sensor is closed with the

internal shutter automatically).

Mode А (automatic)

- The device calibrates by itself according to the software algorithm.

You do not need to close the lens cover (the sensor is closed with the

internal shutter automatically).

- In the automatic mode the user can calibrate the sensor with the

ON/OFF (in the SA mode) button.

The device allows you to quickly increase the basic magnification

(please refer to the line in the specifications table) by 2 or “Digital zoom”

4 times 2 or 4 or 8 times XP models). (XQ models) or (

To operate the discrete digital zoom, press successively the DOWN (5)

button.

The digital zoom will not be saved after the device is re-started.

QUICK MENU FUNCTIONS

Enter the menu with a short press of the М (3) button.

To toggle between the functions below, press successively the M

button.

Select the desired mode in the menu option “CALIBRATION”

INCREMENTAL DIGITAL ZOOM

The Quick menu allows change of basic settings such as display

brightness and contrast, smooth digital zoom.

Brightness – press briefly the UP(2)/DOWN(5) buttons to

change display brightness from 00 to 20.

Contrast – press briefly the UP/ DOWN buttons to change

display contrast from 00 to 20.

Notes.

- actual magnification is the product of the basic magnification value

and continuous digital zoom value.

For example: the device's basic magnification is 3. , smooth digital 1х

zoom value 1.7. Actual magnification is 5. (3. *1.7).х 2х 1

- display brightness and contrast settings are saved in the memory

when the unit is turned off.

- To exit quick menu, press and hold down the M button or wait 5 sec

for automatic exit.

MAIN MENU FUNCTIONS

Smooth digital zoom UP/ DOWN- press the buttons to change

digital zoom from 1.0x to 4.0x (or 8.0x in XP model).

Smooth digital zoom is in 0.1x increments.

Enter the main menu with a long press of the М (3) button.

Press the UP(2) / DOWN(5) buttons to switch between the menu

options.

Menu navigation is cyclical: as soon as the last menu option of the

first tab is reached, first menu option of the second tab starts.

Enter a menu option with a brief press of the М button.

Exit the menu with a long press of the М button.

Automatic exit takes place in 10 sec of inactivity (buttons are not

pressed).

Upon exit from the menu the cursor location is memorized only for

the duration of the working session (i.e. until the unit is turned off).

Upon restarting the device and entering the menu the cursor will be

located on the first menu option.

Rocks

Identiﬁcation

Forest

Automatic

Semi-Automatic

Manual

Black Hot

Red Hot

Red Monochrome

Rainbow

Ultramarine

Violet

Sepia

MENU CONTENTS:

Wi-Fi ON/OFF

Color palettes

Calibration mode

Wi-Fi settings

Operating mode

Language

Date

Clock

Unit of

measurement

Reset

Format

Tab 1

Tab 2

Settings

Remote Control

Device information

Defective pixel repair

Rangefinder

LRF

Reticle shape

TPA function

THD function

Color

palettes

Selecting colour palette

= Basic image mode is “White Hot”

= To select another palette:

Menu contents and description

Wi-Fi Wi-Fi ON/OFF

Oﬀ

= Press and hold down the М (3) button to enter the

main menu.

= Select the desired menu option with the

UP (2) / DOWN (5) buttons.

= Turn Wi-Fi on/off with a short press of the M

button.

Operating

mode

Selecting operating mode

There are three automatic operating modes:

Each mode includes optimal combination of

parameters (brightness, contrast, gain etc.) to

deliver best possible image in specific viewing

conditions.

= Press and hold down the М (3) button to enter the

main menu.

= Select the desired menu option with the

UP/DOWN buttons.

= Confirm your selection with a brief press of the M

button.

Enhanced contrast mode.

Perfect for viewing animals against the background

of rocks, ground in mountain areas.

Rocks

Identiﬁcation

Forest

Low contrast mode

Perfect for viewing animals against a background of

vegetation.

Universal mode for various modes of observation.

= Press and hold down the М (3) button to enter the

main menu.

= Select the desired palette with the UP (2)/DOWN

(5) buttons.

= Confirm your selection with a brief press of the M

button.

Calibration

Wi-Fi

settings

Wi-Fi setup

This menu option allows you to set up your device

for operation in a Wi-Fi network.

This menu option allows you to set a password to

access your thermal imager from an external

device.

The password is used to connect an external device

(i.e. smartphone) to your thermal imager.

= Press and hold down the М (3) button to enter the

main menu.

= Select the menu option with the UP (2)/DOWN (5)

buttons.

= Press briefly the M button to enter submenu

“PAS”.

= The default password “12345” appears on the

display.

Password

setup

12345

Black Hot palette (white colour corresponds to

low temperature, black colour – to high

temperature)

Red Hot

Red Monochrome

Rainbow

Ultramarine

Violet

Sepia

Switch between the palette selected in the menu

and the basic palette by holding down the

UP (2) button.

Selecting calibration mode

There are three calibration modes: manual (M),

semi-automatic (SA) and automatic (А).

= Press and hold down the М (3) button to enter the

main menu.

= Select the desired calibration mode with the UP

(2)/DOWN (5) buttons.

= Confirm your selection with a brief press of the M

button.

More details in the section “Sensor calibration”.

= Set the desired password with the UP / DOWN

buttons (button UP to increase value; button

DOWN to reduce).

= Switch between digits with a short press of the M

button.

= Save the password and exit the submenu with a

long press of the M button.

Access

level setup

Owner

Guest

Access level setup

This menu option allows you to set required access

level of the Stream Vision application to your

device.

= Access level Owner.

The Stream Vision user has the complete access to

all device's functions.

= Access level Guest.

The Stream Vision user has the access only to the

real time video stream from the device.

Settings

The following settings are available:

English

Selecting interface language

= Press and hold down the М (3) button to enter the

main menu.

= Select option “Settings” with the UP (2)/DOWN

(5) buttons. Press briefly М to confirm.

= "Language" with UP/DOWN.Select option

= Press briefly М to confirm.

= Select one of the available interface languages

with a short press of the UP/ DOWN buttons:

English, French, German, Spanish, Russian.

= Switch between languages with a brief press of

the M button.

= Save selection and exit the submenu with a long

press of the M button.

Language

Date

Date setup

= Press and hold down the М (3) button to enter the

main menu.

= Select option “Settings” with the UP (2)/DOWN

(5) buttons. Press briefly М to confirm.

= Select option "Date" with UP/DOWN.

= Press briefly М to confirm.

Time

Time setup

= Press and hold down the М (3) button to enter the

main menu.

= Select option “Settings” with the UP (2)/DOWN

(5) buttons. Press briefly М to confirm.

= Select option "Time" with UP/DOWN.

= Press briefly М to confirm.

= Select the desired time format with a short press

of the UP/ DOWN buttons: 24 or PM/AM.

= Switch to hour setup with a brief press of the M

button.

= Select hour value with a brief press of the UP/

DOWN buttons.

= Switch to minute setup with a brief press of the M

button.

= Select minute value with a brief press of the UP/

DOWN buttons.

= Save selected date and exit the submenu with a

long press of the M button.

Units of

measure

Selection of units of measurement

= Press and hold down the М (3) button to enter the

main menu.

= Select option “Settings” with the UP (2)/DOWN

(5) buttons. Press briefly М to confirm.

= Select option "Units of measure" with

UP/DOWN.

= Press briefly М to confirm.

= Select the desired unit of measurement - metres

or yards - with UP/DOWN. Press briefly М to

confirm.

= E x it t o s ett i ngs sub m e nu t ake s p l ace

automatically.

= Date format is displayed as: YYYY/MM/DD

(year/month/day)

= Select the correct values for the year, month and

date with a short press of the UP/ DOWN buttons.

= Switch between digits with a short press of the M

button.

= Save selected date and exit the submenu with a

long press of the M button.

Reset

Restore default settings

= Press and hold down the М (3) button to enter the

main menu.

= Select option “Settings” with the UP (2)/DOWN

(5) buttons. Press briefly М to confirm.

= Select option "Reset" with UP/DOWN. Press

briefly М to confirm.

= With a short press of the UP/ DOWN buttons

select “Yes” to restore default settings or “No”

to abort.

= Confirm selection with a brief press of the M

button.

= If “Yes” is selected, display will show “Return

default settings?” and “Yes” and “No” options.

Select “Yes” to restore default settings.

= If “No” is selected, action is aborted and you

return to the submenu.

The following settings will be restored to their

original values before changes made by the user:

= Operating mode of video recorder – video

= Unit’s operating mode – Forest

= Calibration mode – automatic

= Language – English

= Wi-Fi – off (default password)

= Magnification – off (no digital zoom)

= PiP – off

= Colour palette – White Hot

= Unit of measurement - metric

Warning: date and time settings, default pixel map

and remote control activation are not restored.

= Enter the Format submenu with a short press of

the M button.

= Press briefly М to confirm.

= With a short press of the UP/ DOWN buttons

select “Yes” to format the memory card or “No”

to return to the submenu.

= Confirm selection with a short press of the M

button.

Format

Formatting

This menu option allows you to format your device's

Flash card or memory card (erase all files from its

memory).

= Press and hold down the М (3) button to enter the

main menu.

= Select option “Settings” with the UP (2)/DOWN

(5) buttons. Press briefly М to confirm.

Rangefinder

Selection of reticle shape

Function “Target position angle” (TPA)

“THD” function

Menu item “Rangefinder” allows you to set up built-in rangefinder’s

parameters as follows:

џ Confirm selection with a brief press of the М (3) button.

џ Selected reticle will appear on the display.

џ The reticle will disappear from the display if the rangefinder is not used

longer than 4 seconds.

џ Function “TPA” allows you to change the angle of target location (angle

of elevation). When the function is activated, the angle is shown

continuously. When the function is disabled, the angle is shown if the

rangefinder is working. The angle is shown in a pop-up menu during

measurement.

џ Select to activate “TPA”.

џ Confirm selection with a brief press of the M (3) button.

џ “THD” function allows you to measure true horizontla distance to a

target based on the angle of elevation value.

џ Select to activate “THD”.

џ Confirm selection with a brief press of the M (3) button. Hereinafter

message THD will appear above the distance readings.

џ Select one of the three reticle shapes with the UP (2) and

DOWN (5) buttons.

= Enter the main menu with a long press of the M (3) button.

= Rangefinder MEnter the submenu " " with a short press of the button.

= parameter UP (2) DOWN (5) buttons.Set the desired with the and

LRF

= If “Yes” is selected, display will show “Do you want to format

memory card?” and “Yes” and “No” options. Select “Yes” to format

the memory card.

= Message «Memory card formatting» means that formatting is in

progress.

= Upon completion of formatting the message «Formatting

completed» is shown.

= If “No” is selected, formatting is aborted and you return to the

submenu.

Remote

Control

Remote control activation (bought separately)

Before operating the remote control (RC),

remember to activate it as follows:

= Display shows message “Wait” and countdown

starts (30 sec), within which hold down for two

seconds any RC button.

= If activation is successful, the message

«Connection complete» appears .

= If error occurs the message «Connection failed»

appears . Repeat the procedure.

= The RC is activated and ready for use.

= To unlink the RC, press the М button, wait for the

countdown to expire without pressing any RC

button for 30 sec.

= All remote controls previously linked to your

device are now unlinked.

= Now you can activate your RC again or activate

another RC.

= Press and hold down the М (3) button to enter the

main menu.

= Select option “ ” with the UP Remote Control

(2)/DOWN (5) buttons. Press briefly М to confirm.

= Press briefly М to confirm.

Defective pixel repair

When operating a thermal imager, defective (dead)

pixels (bright or dark dots with constant brightness)

may become visible on the sensor.

Defective pixels on the sensor may proportionally

increase in size when digital zoom is activated.

Accolade LRF binoculars thermal allow the user to

repair defective pixels on the detector using a

software-based method or to abort deletion.

Defective

pixel repair

= Press and hold down the М (3) button to enter the

main menu.

= Select option “ ” with the Defective pixel repair

UP (2)/DOWN (5) buttons. Press briefly М to

confirm.

= Press briefly М to confirm.

= A marker (H) appears on the left side of the

display.

x=95

y=99

This option allows the user to view the following

information about the device:

= Full name

= SKU number

= serial number

Device

information

Select menu option Device information with a brief press of the M button

to review information.

Return to default defective pixel pattern

This option allows you to cancel deletion of the

defective pixels and return them to the original

state.

= Enter the submenu with a brief press of the M

button.

= Select icon and press М.

= Select “Yes” if you wish to return to default

defective pixel pattern, or “No” if you do not.

= Confirm selection with a short press of the M

button.

= On the right side of the display appears

“magnifying glass” (G) – a magnified image in a

frame with a fixed cross , designed for easier

detection of a defective pixel and to match the

pixel with the marker, horizontal and vertical

arrows for X and Y axes (I) showing marker's

movement.

= With a short press of the UP/ DOWN buttons

move the marker to align it with a defective pixel.

= Switch the direction of the marker from horizontal

to vertical and vice versa with a short press of the

M button.

= Align the defective pixel with the fixed cross in the

frame – the pixel should disappear.

= Delete the defective pixel with a brief press of the

REC (4) button.

= A brief message “OK” appears in the frame in

case of success.

= Then you can delete another defective pixel by

moving the marker along the display.

= Exit “Defective pixel repair” with a long press of

the M button.

Attention! The display of a thermal imager may have 1-2

pixels represented as bright white or color (blue, red) dots

which cannot be deleted and are not a defect.

= software version

= hardware version

= service information

The status bar is located in the lower part of the display and shows

information on the actual operating status of the device, including:

16x

12:30AM

1 2 3 4 5 76

(1) Colour palette

(shown only if the “Black Hot” palette is selected)

(2) Operating mode

(3) Calibration mode

(in the automatic calibration mode, three seconds before automatic

calibration a countdown timer 00:01 is shown in place of the calibration

mode icon).

(4) Current full magnification (for example, 16x)

(5) Wi-Fi connection status

(6) Running time

(7) Battery charge level

(if the device is powered by the Battery Pack) or

External battery power indicator

(if the device is powered by an external power supply)

STATUS BAR

BUILT-IN LASER RANGEFINDER

The binoculars are equipped with a built-in rangefinder (9), allowing

you to measure distance to objects up to 1000m away.

How the rangefinder works:

џ Turn on the device, set up image according to section "Operation",

press the UP (2) or LRF (21) button on remote control - rangefinding

reticle appears; in the top right corner of the display dashes of

distance values with unit of measurement appear, i.e. the rangefinder

enters the stand-by mode.

џ If PiP mode is activated, the aiming reticle disappers upon

activation of the rangefinder and the PiP window remains active.

џ Point the rangefinding reticle at an object and press the "UP"

button.

џ In the top right corner of the display you will see distance in metres

(or yards - depending on settings).

Note: if the rangefinder is idle longer than for three seconds, it turns

off automatically.

The built-in recorder operates in two modes - VIDEO and PHOTO.

VIDEO mode. Video recording

The device in the VIDEO mode upon turning on.

In the top left corner you will see icon and remaining recording

time 5:12.in the format HH:MM (hours: minutes)

Start video recording with a short press of the REC (4) button.

Upon start of video recording icon disappears, and icon REC and

recording timer in the format MM:SS (minutes : seconds) appear

instead:

REC 00:25

VIDEO RECORDING AND PHOTOGRAPHY

Accolade LRF thermal imaging binoculars feature video recording and

photography of the image being ranged to the internal memory card.

Before using this feature, please read the menu options “Date setup”,

“Time setup” of the section “Main menu functions”.

џ Accuracy of measurement and maximum range depend on the

reflection ratio of the target surface, the angle at which the emitting

beam falls on the target surface and environmental conditions.

Reflectivity is also affected by surface texture, colour, size and shape

of the target. A shiny or brightly coloured surface is normally more

reflective than a dark surface.

џ Measuring range to a small sized target is more difficult than to a

large sized target.

џ Accuracy of measurement can also be affected by light conditions,

fog, haze, rain, snow etc. Ranging performance can degrade in bright

conditions orwhen ranging towards the sun.

Peculiarities of operation

Operation in SCAN mode:

џ To measure distance in scanning mode, hold down the UP (2) or

LRF (21) button on remote control for longer then two seconds.

Measurement readings will be changing in real time as you point the

binoculars at different objects. Message SCAN appears in the top right

corner.

џ To exit SCAN mode, press UP or LRF (RC) button again.

џ If measurement fails, dashes will appear on the display.

џ In 3-4 seconds of inactivity (no measurement is taken) the

rangefinder turns off, the rangefinding reticle with readings disappears

from the display.

Notes:

џ To select a rangefinding reticle, please go to the respective menu

option.

џ To select a unit of measurement (metres or yards) go to "Settings".

Attention!

- Maximum duration of a recorded file is seven minutes. After this

time expires a video is recorded into a new file. The number of

recorded files is limited by the capacity of unit's internal memory.

- check regularly the free capacity of the internal memory, move

recorded footage to other storage media to free up space on the

internal memory card.

To playback video ﬁles recorded by thermal imaging devices on iOS-

based computers, we recommend that you use VLC video player or

Elmedia player.

Download links and QR codes are shown below:

VLC VIDEO PLAYER ELMEDIA VIDEO PLAYER

http://www.videolan.org/

vlc/download-macosx.html

https://itunes.apple.com/us/

app/elmedia-multiformat-video/

id937759555?mt=12

IMPORTANT!

Photo mode. Photography

Switch to the Photo mode with a long press of the (4) button. REC

Take a picture with a brief press of the REC button. The image freezes

for 0.5 sec and a photo is saved to the internal memory.

in the top left corner of the display you can see: photography icon ,

“>100” means that you can take more than 100 pictures. If the

number of available pictures is less than 100, actual amount of

available pictures (for example 98) is shown next to the icon .

Notes:

- you can enter and operate the menu during video recording;

- recorded videos and photos are saved to the built-in memory card in

the format img_xxx.jpg (photos); video_xxx.avi (videos). xxx – three-

digit counter for videos and photos;

- counter for multimedia files cannot be reset;

Pause and resume recording video with a short press of the REC

button.

Stop recording video with a long press of the REC button.

Video files are saved to the memory card after stopping video.

Switch between modes (Video-> Photo-> Video) with a long press of the

REC button.

The DISPLAY OFF function deactivates transmission of image to the

display by minimizing its brightness. This prevents accidental disclosure.

The device keeps running.

When the device is on, hold down the ON/OFF (1) button. Display goes

out, message “Display off”.

To activate the display, press briefly the ON/OFF button.

When holding down the ON/OFF button, the display shows “Display

off” message with countdown, the device will turn off.

FUNCTION DISPLAY OFF

Connection status

Status bar indication

WI-FI FUNCTION

Your thermal imager features wireless connection option (Wi-Fi) which

links it with external appliances (smartphone, tablet PC).

Turn on the wireless module in the respective menu option.

Wi-Fi operation is shown in the status bar as follows:

Wi-Fi is off

Wi-Fi activated by the user,

Wi-Fi in the device is being

activated

Wi-Fi is on, no connection with

device

Wi-Fi is on, device connected

Your device is detected by an external device as “Accolade

LRF_XXXX”, where XXXX – is the last four digits of device's serial

number».

After a password is generated on an external appliance (please refer

to the menu option “Wi-Fi setup” of the section “Main menu

functions” of this user manual) and connection is established, the

icon in the status bar changes to .

FUNCTION PiP

PiP (“Picture in Picture”) allows you to see

a zoomed image simultaneously with the

main image in a dedicated window.

6.9x

3.1x

Turn on/off the PiP function with a long

press of the DOWN (5) button.

Change zoom ratio in the PiP window with a short press of the DOWN

button.

The zoomed image is displayed in a dedicated window, with the full

optical magnification being shown.

The main image is shown with optical magnification ratio which

corresponds to ratio x1.0.

When PiP is turned on, you can operate the discrete and continuous

digital zoom. The full optical magnification will take place only in the

dedicated window.

When PiP is turned off, the image is shown with the optical

magnification set for the PiP function.

STREAM VISION

Accolade LRF thermal imaging binoculars support Stream Vision

technology which allows you to stream an image from the display of your

thermal imager to a smartphone or tablet PC via Wi-Fi in real time mode.

You can find further guidelines on Stream Vision on our web site

www.pulsar-nv.com

Note: the Stream Vision application allows you to update the firmware

features of your thermal imager.

Scan the QR codes to download Stream Vision free of charge:

Google Play (Android OS): iTunes (iOS):

Connection modes:

Memory card (external memory).

In this mode the device is detected by the computer as a flash card.

This mode is designed for work with the files saved in device's

memory. The device's functions are not available in this mode; the

device turns off automatically.

If video recording was in progress when connection was made,

recording stops and video is saved.

When USB is disconnected from the device where connection is in

the USB Mass storage device mode, the device remains on the OFF

state. Turn the device on for further operation.

Power.

In this mode PC/laptop is used as an external power supply. The

status bar shows icon . The device continues operating and all

functions are available.

Note: The Battery pack installed in the device is not being charged!

When USB is disconnected from the device when in the Power mode,

the device keeps operating with Battery Pack, if available, and it has

sufficient charge.

USB CONNECTION

Connect one end of the USB cable (16) to the Micro-USB (15) port of

your device, and the other end to the USB port of your PC/laptop.

Turn the device on with a short press of the ON/OFF (1) button (device

that has been turned off cannot be detected by your computer).

Your device will be detected by the computer automatically; no drivers

need to be installed.

Two connection modes will appear

on the display:

Memory card (external memory)

and Power.

Select connection mode with UP

and DOWN buttons.

Confirm selection with a short press of the M button.

USB connection

Use as power

Use as memory card

Check the objective and eyepieces lenses; rangefinder’s emitter

and receiver lenses. If required, remove dust and sand (preferably

by a noncontact method). Clean the external surfaces of the lenses

with products expressly designed for this purpose.

Store the device in a carrying case. Remove the Battery Pack

for long-term storage.

Maintenance should be carried out no less frequently than twice a

year, and should consist of the following measures:

MAINTENANCE AND STORAGE

Wipe external plastic and metal surfaces clean of dust and dirt with

a soft cloth moistened with a synthetic cleaning agent.

Clean the electric terminals of the Battery Pack and device's battery

slot using a grease-free organic solvent.

WIRELESS REMOTE CONTROL

(bought separately)

Wireless remote control (RC) duplicates the power on function,

digital zoom, rangefinder control, and menu navigation.

Brief press Enter quick

Turn on

device /

Calibrate

sensor

Controller

(18)

Button

ON (19)

Activate

incremetal

zoom

Button

ZOOM (20)

Activate

rangefinder /

Measure

distance

Button

LRF (21)

Long press Enter main

Display Off /

Turn off

device

Activate

function PiP

Activate

SCAN mode

Clockwise

rotation

Increase

parameter,

move upwards

Counter-

clockwise

rotation

Decrease

parameter,

move

downwards

TROUBLESHOOTING

The table presented below lists some potential problems that may occur

when using the device. If a problem encountered with the device is not

listed, or if the recommended action does not resolve the problem, the

unit should be returned for repair.

The thermal imager

will not turn on.

The device does not

operate on external

power supply.

Battery Pack is discharged.

USB cable is damaged.

Charge the battery.

Replace USB cable.

Check

Corrective action

Problem

External power supply is

discharged.

Charge the external power

supply (if necessary).

The image is blurry,

with vertical stripes

and uneven

background.

The image is too

dark.

Poor image quality /

Detection range

reduced.

Calibration is required.

Brightness or contrast level

is too low.

Problems described may arise in adverse weather conditions

(snow, rain, fog etc.).

Carry out calibration according

to Section

“SENSOR CALIBRATION”.

Adjust brightness/contrast with

the UP/DOWN buttons.

Smartphone or tablet

PC cannot be

connected to the

device.

Password in the unit was

changed.

Delete network and connect

again inserting the password

saved in the device.

There are too many Wi-Fi

networks in the area where the

device is located which may

cause signal interference.

To ensure stable Wi-Fi

performance, move the device

to an area with few or no Wi-Fi

networks.

TECHNICAL INSPECTION

Check:

External view (there should be no cracks on the housing).

The state of the objective and eyepiece lenses (there should be no

cracks, spot, dust, deposits etc.).

The state of the Battery Pack (should be charged) and electric

terminals (there should be no oxidation).

Correct functioning of the controls.

The device does not

operate on external

power supply.

Battery Pack is not

installed on the

device.

Stable operation of the

device with certain external

power supplies (like power

bank) is not guaranteed

unless the standard

IPS5/IPS10 Battery Pack is

installed.

Before using an external power

supply, install the Battery Pack

(it may be empty) on the

device. You can remove the

Battery Pack once the device

turns on.

Place the in line-of-sightdevice

of the Wi-Fi signal.

No Wi-Fi signal or

erratic signal.

The device cannot

be powered on

with wireless remote

control.

When using the

scope at below zero

temperatures the

image quality is

worse than at

positive

temperatures.

Problem

The device is beyond reliable

Wi-Fi range.

There are obstacles between

the device and the signal

receiver (i.e. concrete walls).

Remote control is not

activated.

Low battery.

Activate the remote control

according to instructions.

Install a new CR2032 battery.

Because of variations in thermal conductivity, objects (surrounding

environment, background) under observation become warm more

quickly at above-zero temperatures, which allows higher

temperature contrast and, thus, the quality of the image produced

by a thermal imager will be better.

At low operating temperatures, objects under observation

(background) normally cool down to roughly identical

temperatures, which leads to lower temperature contrast, and to

image quality (precision) degradation. This is normal for thermal

imaging device.

Check

Corrective action

Rangefinder will not

measure distance.

There is an object in front of

the receiver or emitter lens

preventing signal

transmission.

Make sure that: the lenses are

not blocked by your hand or

fingers; the lenses are clean.

Inclement weather conditions (rain, mist, snow).

Large measurement

error.

The device is not being held

steadily when measuring.

Do not stress the device

when measuring.

Distance to the object

exceeds 1000 m.

Pick an object at a distance

longer than 1000m.

Pick an object with higher

reflection ratio (see point

”Peculiarities of operation”

in section 14.

Low reflection ratio (for

example, tree leaves).

Follow the link to read FAQs on thermal vision

http://www.pulsar-nv.com/support/faq/

Оптические характеристики

МОДЕЛЬ Accolade LRF

XQ38

77415

SKU#

Тип

Разрешение, пикселей

Частота обновления кадров, Гц

Размер пикселя, микрон

Оптические характеристики:

Оптическое увеличение, x

Плавный цифровой зум, x

Цифровой зум

Объектив

Минимальная дистанция фокусировки, м

Диаметр выходного зрачка, мм

Угол поля зрения (ГxВ), град / м на 100м

Диапазон фокусировки

окуляра, дптр

Макс. дистанция наблюдения (объект -

животное типа "олень"), м, около

Дисплей:

Тип

Разрешение, пикселей

Эксплуатационные

характеристики:

Напряжение питания

Тип батарей / Емкость /

Выходное напряжение

Внешнее питание

Время работы от батареи

(при t=22 °C), ч*

Степень защиты, код IP

(IEC60529)

Диапазон эксплуатационных

температур

Габариты, мм

Масса (без батареи), кг

Видеорекордер

Разрешение видео/фото, пикселей

Формат видеозаписи / фото

Объем встроенной памяти

Емкость встроенной памяти

Wi-Fi канал

Частота

Стандарт

Дальность приема в прямой

видимости, м

неохлаждаемый

384x288

3,1

3,1-12,4

1:1,2

9,8 / 17,2

1350

AMOLED

640x480

3,7В

Battery Pack / 5000 мАч /

3,7В

IPХ7

-25 °С ... +50 °С

164x130x64

0,6

640x480

.avi / .jpg

8 Гб

150 мин видео или более 10 000 фото

802.11 b/g/n

XP50

77418

неохлаждаемый

640x480

2,5

2,5-20

12,4 / 21,8

±5

1800

AMOLED

640x480

IPХ7

-25 °С ... +50 °С

164x130x64

0,6

640x480

.avi / .jpg

8 Гб

2,4ГГц

802.11 b/g/n

1:1,2

2x/4x

±5

2,4ГГц

2x/4x/8x

Межзрачковое расстояние, мм

56-71

3,7В

5В 5В

Тепловизор Accolade LRF

Чехол

Аккумуляторная батарея IPS5

Зарядное устройство с

сетевым адаптером

Кабель microUSB

КОМПЛЕКТ ПОСТАВКИ

Для улучшения потребительских свойств изделия в его конструкцию и

программное обеспечение могут вноситься усовершенствования.

Актуальную версию инструкции по эксплуатации Вы можете найти на сайте

www.pulsar-nv.com

Шейный ремень

Инструкция по эксплуатации

Салфетка для чистки оптики

Гарантийный талон

ОПИСАНИЕ

ОТЛИЧИТЕЛЬНЫЕ ОСОБЕННОСТИ

Встроенный лазерный дальномер (до 1000м)

Удобство наблюдения

Изменяемое межзрачковое расстояние

Частота обновления кадров 50 Гц

Встроенный видеорекордер

Встроенный модуль Wi-Fi

Передача видео через Wi-Fi

Трансляция видеопотока в Интернет в режиме реального времени

Морозоустойчивый AMOLED дисплей

Перезаряжаемые быстросъемные аккумуляторные батареи

с продолжительным временем автономной работы

Полная водонепроницаемость (IPX7)

Основные особенности:

* Фактическое время работы зависит от степени использования Wi-Fi, видеорекордера и

встроенного лазерного дальномера.

** Зависит от характеристик объекта измерения, условий окружающей среды.

Дальномер

Длина волны, нм

Макс. дистанция измерения, м**

Точность измерения, м

905

1000

+/-1

905

1000

+/-1

Тепловизионные бинокли Accolade LRF на базе ИК-матрицы

(микроболометра) представлены рядом моделей с различным

увеличением и разрешением сенсора. Accolade LRF обеспечивают

удобство наблюдения обоими глазами.

Бинок ли оснащены встроенным высокоточным лазерным

дальномером, предназначенным для измерения дистанции до

объекта на расстоянии до 1000м.

Бинокли предназначены для использования как ночью, так и днем в

сложных погодных условиях (туман, смог, дождь), а также при

наличии препятствий, затрудняющих обнаружение цели (ветки,

высокая трава, густой кустарник и т.п.). Бинокли не нуждаются во

внешнем источнике света, что позволяет использовать их в полной

темноте.

Тепловизионные бинокли Accolade LRF предназначены для

различных сфер использования, таких как ночная охота, наблюдение

и ориентирование на местности, проведение спасательных

операций и др.

ЭЛЕМЕНТЫ ПРИБОРА И ОРГАНЫ УПРАВЛЕНИЯ

Кнопка включения/калибровки ON/OFF

Кнопка навигации UP

Кнопка MENU

Кнопка записи REC

Кнопка навигации DOWN

Кольца регулировки межзрачкового расстояния

Кольца диоптрийной настройки окуляра

Ручка фокусировки объектива

Аккумуляторная батарея

Рычаг для фиксации аккумуляторной батареи

Штативное гнездо

Радиатор охлаждения

Крышка объектива

Объектив

Разъем microUSB

Кабель microUSB

Встроенный лазерный дальномер

Режим “Картинка-в-картинке” (PiP)

Цветовые режимы

Режимы наблюдения

Режимы калибровки

Ручная регулировка контраста и яркости изображения

Дополнительные особенности:

Pиc. 1

Страница загружается ...

Pulsar Accolade LRF XQ38 Руководство пользователя

Бренд: Pulsar

Модель: Accolade LRF XQ38

Тип: Руководство пользователя

Это руководство также подходит для

Accolade LRF XP50

Скачать PDF

сообщить о нарушении

на других языках

English: Pulsar Accolade LRF XQ38 User manual

Pulsar Accolade LRF XQ38 Руководство пользователя

Это руководство также подходит для

Pulsar Accolade LRF XQ38 Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов