HYUNDAI H-SA6041
H-SA6041
4-WAY CAR AMPLIFIER 4-
Instruction manual
HYUNDAI H-SA6041
2
YOUR NEW HIGH FIDELITY BRIDGEABLE/STEREO AMPLIFIER IS DESIGNED TO DELIVER MAXIMUM ENJOYMENT AND ONE YEAR OF
TROUBLE FREE SERVICE.
Features
· Four Class ''AB'' High-Current Dual Discrete Drive Stages.
· Class ''AB'' Technology MOSFET PWM Power Supply.
· Bridgeable & TRI-Mode Operation.
· Continuously Variable 12dB/Octave High Pass & 12dB/Octave Low Pass Crossover.
· Subwoofer Variable Crossover for Deep Bass Control.
· Enhanced Bass Boost 0/+6/+12dB @50Hz
· Silver Plated RCA & Power, Speaker Terminal.
· Soft Start & Muting.
· Overload, Thermal, Short Circuit Protection.
· Power & Protection indicator.
Precautions: Read First!
· If after reading the direction you feel uncomfortable about installing the amplifier in your car, or not equipped or competent to do so, you should have the
amplifier installed by an authorized installer. It's your car!
· Negative battery terminal must be disconnected before any electrical connections are made.
· Be sure choose a location that provides substantial ventilation for the amplifier.
· The most preferred locations would be in your car's trunk, under the front seats or on the back wall of a truck.
· The location chosen should provide at least 2" of clearance above the amplifier for adequate ventilation.
· If the amplifier is to be mounted vertically be sure that it is in a place where adequate air will flow along the length of its heatsink fins for cooling.
· NEVER mount the amplifier up side down, this will cause the heat to rise back into the amplifier causing thermal shutdown or possible permanent
damage.
· NEVER mount the amplifier in a location that is subject to direct sunlight or exposed to moisture.
· Be sure to mount the amplifier to a strong, solid surface which will not give way under the stress of a sudden stop or accident.
· Make sure that the mounting screws will not penetrate the gas tank, brake and fuel lines, wiring or other critical parts of your car when installed.
· NEVER operate the amplifier without the proper power and ground wire 10 gauge minimum.
· NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery. This fuse is to protect the car not
the electronics. In case of a short, the fuse will blow instead of the wire burning up. Using other than the recommended fuse ratings at the battery and at
the amplifier may cause damage to the amplifier and will void your warranty.
· Do not run wiring underneath or outside the car since exposure to the elements may cause the insulation to deteriorate rapidly, resulting in short-circuits
and/or intermittent operation. All cables should be run beneath carpets and inside trim pieces.
· To help minimize interference, it is best to run the power cables along the opposite side from the audio cables.
HYUNDAI H-SA6041
3
· Whenever wires pass through metal, rubber or plastic grommets must be used to prevent the mental from wearing through the installation and causing a
short.
· Whenever possible, use cable ties, mounting clamps and similar wiring aids (available from an electrical supply or auto parts store) Adding stress relief
loops to wiring is also advisable to prevent straining or breakage.
· It is best to test the system before the amplifier is mounted and interior of car is reassembled.
· If the temperature inside your car reaches extreme levels (such as sitting locked up for several hours in the hot sun or exposed to a very cold winter's
day)the amplifier may go into protection mode and shut off. Leave the unit off until the ambient temperature returns to normal.
· The amplifier operates with any vehicle using a 12 volt negative ground system. If you are not sure of the type of electrical system in your vehicle,
consult your authorized dealer or qualified mechanic.
· NEVER ground the speaker leads and NEVER allow the speaker leads to come in contact with each other. Speaker wire should be 18 gauge or larger.
· Remote turn on wire must be switched by the radio does not have a remote turn on or antenna output, connect to wire that has a positive 12 volts when
the key is turned to the accessory. If the amplifier does not turn off the battery will die.
· Do not listen to high volumes for extended periods of time or hearing damage may occur.
CONTINOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER 100dB
MAY CAUSE PERMANENT HEARING LOSS. HIGH POWERED AUTOSOUND
SYSTEM MAY PRODUCE SOUND PRESSURE LEVELS WELL OVER
130dB. USE COMMON SENSE AND PRACTICE SAFE SOUND.
Installation
MOUNTING:
1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1.
2. Once the location has been determined, place the amplifier in position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER
use the amplifier as a template for drilling. It is very easy to damage the amplifier surface in manner.
3. Remove amplifier. Drill four 3.5 mm. Diameter holes into mounting surface on steel panel. If you want mounting the MDF or wood panel, drill four 3.0m/m
diameter holes into mounting surface.
4. If possible, test the system operating before final mounting of the amplifier.
5. Mount the amplifier using the supplied 4 self threading screws.
HYUNDAI H-SA6041
4
INSTALLATION DIAGRAM
Fig.1
CONNECTIONS
INPUT CONNECTIONS
· This amplifier will accept low level inputs. Low level is the same as line level. The low level signal is carried through RCA cables. It is preferred to use
low level inputs to the amplifier if the head unit is equipped with the low level outputs. If not, you can use a "high to low converter" available through
your local car audio shop.
· Connect the low level/line level RCA cables from the head unit, or signal processor, to the line level input on the amplifier. See Fig.3 system wiring
diagrams.
HIGH INPUT CONNECTIONS
Connect the HIGH LEVEL INPUT connector wires to the speaker level of the unit as in the diagram. Use #18 or thicker stranded, insulated hookup wire.
Fig.2.
HYUNDAI H-SA6041
5
POWER CONNECTIONS
It is important to have good quality power and ground connections. Remember, to complete an electrical circuit, the ground connection is just as important
as the positive power connection. Before any power connections are made, disconnect the ground cable at the battery.
When the power supply lead, memory backup lead or ground lead are extended, use a 5mm
2
or larger automotive grade cable which will withstand friction
and heat to safe guard against fires occurring as a result of short-circuiting.
Ground-Connect the proper gauge ground wire to the amplifier "GND" terminal. Locate the position on the chassis of the car to which the amplifier is to be
ground. The surface must be free from any paint or dir. This can be accomplished with a small grinding bit or wire wheel. NOTE: Do not ground amplifier to the
"frame" of the car, the frame on most cars and trucks is not grounded to the chassis(body). Solder or clamp ring terminal to ground wire. Pretrial the prepped
chassis metal to bolt the ground ring terminal with nut, bolt and lock washers. Insulate mental and connector with paint or silicon to prevent rust and oxidation.
Silicon also works great to prevent nuts and bolts from working loose in a harsh environment of an automobile. Upon completion of ground connection, grab
wire or connector and confirm that it is a solid connection. To prevent engine noise, it is recommended to ground the head unit and other audio electronics in the
same location.
Remote Turn-on-Connect smaller light gauge wire to "REMOTE" terminal of amplifier and to remote/antenna turn-on output or "remote amplifier" of head
unit. If head unit is not equipped with a remote/antenna output, locate a wire that is controlled by the accessory position of the key. It is important to have the
amplifier turn off with the radio or key. If the amplifier remains on, the result will most likely be a dead battery.
Positive-Connect the proper size wire to the amplifier "B+" terminal of amplifier. Run wire to wards the fuse holder that is no greater then 0.5 meters from
the battery. Remember, the fuse is to protect the safety of the car in the case of a short. Connect fuse holder to battery, however, do not install fuse at this time.
Fig.3.
HYUNDAI H-SA6041
6
SPEAKER CONNECTIONS
This amplifier can operate in either one, two or three channel mode. The minimum impedance for single channel (bridged/mono) operation is 4-8 ohms. There
channel tri-power is referred to stereo and mono at the same time. Minimum impedance remain the same for three channel (satellite/ subwoofer) systems as long
as proper passive crossovers are used. Connect right and left speaker wire to corresponding speaker output terminals of the amplifier. Be sure to have the positive
wire from the speaker to the positive speaker terminal of the amplifier and the negative wire from the speaker must connect with the negative speaker terminal of
the amplifier. Reversing any of these connections will result in the speaker cones moving out of phase which causes bass cancellation. See Fig.4 Speaker Output
Connections.
Fig.4.
HYUNDAI H-SA6041
7
ADJUSTMENTS
1.Set to the "H.P.F" position when the amplifier is used to drive a tweeter/midrange system. The frequencies below the crossover point will be attenuated at
12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz as the crossover point.
2.Set to the "L.P.F" position when the amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12dB /octave.
Permits adjustment of the crossover frequency, by rotating the knob to select any frequency between 40Hz to 150 Hz as the crossover point.
3.Set to the "OFF" position when the amplifier will be used for driving full-range speakers. The full frequency bandwidth will be output to the speakers without
high or low frequency attenuation.
4.Level adjustment-The sensitivity adjustment is to allow the amplifier to work with many different brands of head units. It allows input signal to vary between
350 millivolts to 5 volt from the head unit or other signal processor. Start by setting the sensitivity adjustment to the "MIN" (3 volts). Using a cassette or compact
disc that you are familiar with ,turn on head unit to the 3/4 volume setting. Slowly turn up sensitivity adjustment towards the "MAX" (200 millivolts) using a flat
head screw driver. Stop turning on the onset of distortion and turn back just a slight. The 3/4 volume setting is now the "maximum" volume for the head unit.
The goal is to keep the level control to the lowest setting yet still have enough signal to drive the amplifier. This is done to prevent over driving the amplifier and
to keep system noise to a minimum. It is important not over drive speakers (at point of distortion) this will cause permanent damage to the speakers. Also, if the
amplifier itself is over driven, it could be damaged.
5.The "BASS" function can be selected to increase low frequency response output, or decrease frequency response output. The "BASS" function will be working
at only "OFF" or "L.P.F" position. The BASS is adjustable from 0/+6/+12dB boost at 50Hz.
Fig.5.
HYUNDAI H-SA6041
8
TROUBLE SHOOTING GUIDE
· Before you consult this listing, make sure the vehicles electrical system is working properly by verifying that other electrical items (e. g. headlights,
Windows, etc.) still function correctly.
SYMPTOM PROBABLE CAUSE SOLUTION
Low or N.C. remote turn-on connections Check remote turn-on voltage at amp and head unit
Blown fuse Replace with new fast-blow fuse
Power wires not connected
Check butt splices or solder joints;
Check ground and battery connections
No audio
Blown or non-speakers connected
Use VOM or DVM to measure speaker coil impedance; check speaker
wiring connections
Input sensitivity not set properly or damaged
speaker cones
See adjustment procedure and check each ste; inspect each speaker for
damage and repair or replace suspected component
Distorted audio
Low turn-on voltage Refer to head unit owners manual
Audio level low Mute circuits is on head unit
Check electrical system for low voltage;
Check ground connection
Audio lacks
Speakers wired with wrong polarity, causing
cancellation of bass frequencies
Check polarity of wires from amplifiers to each speak as defined by
the system design;
Check battery voltage at amplifier during operation
External fuse blowing Incorrect wiring or short circuit Refer to electrical installation and check each installation step
Whining noise on audio
with engine running
Amplifier is picking up alternator noise
Install a line noise filter on the head units power wire;
Check alternator routing diodes or voltage regulator for proper
operation. Check all grounds, check battery voltage, check RCA
cables
Ticking noise on audio
with engine running
Amplifier is peaking up radiated spark noise
Check RCA audio cable; Install an in-line noise filter on the head
units power wire, check spark plug wires
HYUNDAI H-SA6041
9
SPECIFICATION
MODEL
H-SA6041
4 OHMS @ 0.5% 0Hz - 30kHz) THD (2 60 W 4
OUTPUT OF
BRIDGED(BTL)
2 OHMS @ 0.5% THD 120 W 4
OPERATION INTO 4 OHMS @ 1KHz, 1% THD 500 W 1
LOW PASS FILTER
(VARIABLE)
50 Hz 250 Hz
HIGH PASS FILTER
(VARIABLE)
80 Hz 1.2 kHz
MAXIMUM OUTPUT POWER 500 W
FREQUENCY RESPONSE (-1dB) 10 Hz 40 kHz
SIGNAL TO NOISE RATIO (`A' WTD) >100 dB
INPUT SENSITIVITY 200 mV - 6V
INPUT IMPEDANCE 22 kOhms
OPERATION VOLTAGE (NEGATIVE GROUND) DC 12V
SPEAKER IMPEDANCE @ STEREO DRIVEN 4 Ohms
FUSE RATING 40A
DIMENSIONS (W x H x D) mm 272 59 280
NOTE : Specifications & design subject to change without notice for improvements.
HYUNDAI H-SA6041
2- !
. ,
.
· «A» MOSFET PWM.
· .
· 12 .
· .
· 0/+6/+12 50 .
· RCA, .
· .
· , .
· .
· , ,
- !
· , , .
· , . ,
.
5 .
· , .
· ,
.
· .
· , , .
· , , , ,
.
· () , 5,27
2
.
· . 0,5
. ; ,
. , ,
, .
HYUNDAI H-SA6041
11
· , ,
; .
· (, ).
· , ,
.
· (, .), ,
.
· , .
· , , , .
, .
· , 12 «». ,
, .
· . 0,832
2
· ( ),
, , +12.
,
· , .
( 100 ) .
130 . !
· , .
· .
, .
· 4 3,5 3,0.
· .
· (.1).
HYUNDAI H-SA6041
12
.1.
· . RCA .
, .
· (, ) RCA (.2).
· (HIGH LEVEL INPUT)
0,832
2
, :
4-
: 1 + + 3 :
: 1 - 3 :
: :
: 2 - - 4 :
: 2 + + 4 :
. 2.
HYUNDAI H-SA6041
13
· .
· 5
2
, .
· «GND» .
.
:, .
· .
· () . ,
, .
· , .
· .
· «REMOTE» «remote amplifier» . ,
, .
· «+» ,
0,5 . .
.
.3.
HYUNDAI H-SA6041
14
· - .
4 - 8 .
· , .
· , () (. .4).
.4.
HYUNDAI H-SA6041
15
· «.F», -
. 12 . 80
1,2 , .
· «L..F», .
12 . 40 150 ,
.
· , «OFF». .
· ,
. 350 5. , «MIN» (3).
CD ¾
( «» (200). ,
. , ¾ - .
, , .
· «BASS» 0/+6/+12 50 ( «L.P.F» «OFF»).
.5.
HYUNDAI H-SA6041
16
· .
.
,
, ,
,
(, ).
.
, RCA
.
RCA ;
;
,
HYUNDAI H-SA6041
17
H-SA6041
4 @ 0,5% . .(20 -
30 )
60 4
,
/
2 @ 0,5% . 120 4
(4 ) @ 1 ; 1%
. .,
500 1
50 250
80 1,2
, 500
(-1 ) 10 40
( WTD) >100
200 6
22
() =12
4
, 40
(), 27259280
.
/