2
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully
before connecting, operating and/or adjusting the product and keep the manual for reference in the future.
Table of contents
TABLE OF CONTENTS ..............................................................................................................................................2
IMPORTANT SAFEGUARDS.....................................................................................................................................3
ACCESSORIES...........................................................................................................................................................4
INSTALLATION/CONNECTIONS ............................................................................................................................5
PANEL CONTROLS....................................................................................................................................................10
GENERAL OPERATIONS...........................................................................................................................................14
SYSTEM SETUP..........................................................................................................................................................17
UTILITIES....................................................................................................................................................................19
RADIO OPERATIONS................................................................................................................................................20
TV OPERATIONS........................................................................................................................................................ 23
AV-IN MODE...............................................................................................................................................................24
DISC/USB/SD/MMC OPERATIONS .......................................................................................................................25
HANDLING COMPACT DISCS.................................................................................................................................32
CLEANING...................................................................................................................................................................32
TROUBLESHOOTING GUIDE ..................................................................................................................................33
SPECIFICATION.........................................................................................................................................................35
3
Important safeguards
Read carefully through the manual to familiarize yourself with this unit.
Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons
who have not read through this manual to use this unit.
“CLASS 1 LASER PRODUCT”
This product contains a laser diode of higher class than 1. Laser beams from the optical pickup are
dangerous to the eyes. To ensure continued safety, do not remove any covers or attempt to gain access
to the inside of the product. Refer all servicing to qualified personnel.
Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this
unit, smoke, and overheating could result from contact with liquids or dust. Protect this unit from
moisture.
Make sure that foreign objects do not get inside the unit; they may cause malfunctions, or create safety
hazards such as electrical shock or laser beam exposure.
The beginning of operation is the moment of the unit installation. Before use the device in winter it is
recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.
Using the unit with the temperature that goes beyond the operation temperature greatly decreases the
operation resource of the screen and other components of the unit and can result in an outage.
Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.
The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please
ensure it before installation.
When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher
amperage rating may cause serious damage to the unit.
Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may
overload or burn out the power amplifier.
Make sure you disconnect the power supply and aerial if you will not be using the system for a long period
or during a thunderstorm.
Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an
unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a
qualified technician check the system.
Always keep the volume low enough so that you can hear sounds from outside the vehicle.
Should this product fail to operate properly, contact your dealer or nearest service center.
4
Accessories
1. Receiver 1 pc
2. Front panel 1 pc
3. Protective bag 1 pc
4. Remote controller 1 pc
5. ISO connector 1 pc
6. Audio-video connector 1 pc
7. Mounting parts:
Mounting sleeve 1 pc
Outer trim ring 1 pc
Steel bar 1 pc
Screw B15x6 1 pc
Nut M5 1 pc
Flat washer 1 pc
Spring washer 1 pc
Bolt M5 4 pcs
Release keys 2 pcs
8. Memory card with Navigation 1 pc
9. Navigation license card 1 pc
10. Consumer information 1 pc
11. Warranty card 1 pc
12. Instruction manual 1 pc
5
Installation/Connections
Choose the mounting location where the unit will not interfere with the normal driving function of the
driver.
Before finally installing the unit, connect the wiring and make sure that the unit works properly.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the
vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
If installation angle exceeds 30° from horizontal, the unit may not perform properly.
Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or
from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.
Mounting
Remove the mounting sleeve (1) from the unit.
Slide the mounting sleeve into the 2-DIN
installation slot provided for the car radio.
Attach the mounting sleeve by bending the
installation brackets towards the outside with a
screwdriver. The sleeve is properly installed
when it can no longer be pulled out, yet also
keeps from sliding into the installation slot.
Connect the cable set and the antenna to the
vehicle’s electronics corresponding to the
connection table (see farther).
Attach the mounting racks to the sides of the
unit, and fix them with the screws as in (2).
Insert the unit into the mounting sleeve until the
stop (3). The unit then audibly snaps into the
sleeve.
Fasten the four screws (4) to fix the unit to the mounting sleeve.
6
Place the trim ring (5) over the unit and the installation is completed. (Some vehicles may not need a
trim ring).
The device is distinguished by a high degree of output. During operation, this results in a strong heat
generation. Therefore no cables or other parts may adjoin the device. If their insulation melts, there is
the risk of a short circuit or fire.
Removing: Turn off the device. Remove the front panel and place it into the protective case. Clamp off
the negative pole of the vehicle battery for the duration of the disassembly. First carefully remove the
trim ring (5) of the unit, by slightly pulling it upwards and then towards you. Now unscrew the four
screws as shown in (4). Remove carefully the unit from the mounting sleeve and disconnect all wires.
Make sure that no vehicle cable can cause a short circuit after the device has been unplugged.
Detachable control panel
To attach the front panel, insert the upper side of the panel first and make sure the connection pins slide
into the connection slots and then press the lower part of the panel to the unit until hear a click.
Slant the front panel down. Press the release lock (in the bottom of the front panel) upward to release the
front panel, and then take out the front panel by pulling it downwards and then towards you from the
bottom. Once the front panel is removed, the back plate will close automatically after a few seconds and
the panel status indicator will blink.
Note: The control panel can easily be damaged by shocks. After removing it, place it in a protective case and
be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and
the control panel is an extremely important part. Be careful not to damage it by pressing on it with
fingernails, pens, screwdrivers, etc.
Note: If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in
isopropyl alcohol to clean the socket on the back of the control panel.
Anti-theft system
The front panel of this unit can be stored in the included protective case when not in used and carried away
when you leave the vehicle to deter theft.
Switch off the power of the unit. Detach the front panel, then put it to the protective case and take it with
you.
8
Using the ISO Connector
1. If your car is equipped with the ISO connector, then connect the ISO connectors
as illustrated.
2. For connections without the ISO connectors, check the wiring in the vehicle
carefully before connecting, incorrect connection may cause serious damage to
this unit.
Cut the connector, connect the colored leads of the power cord to the car battery as
shown in the colour code table below for speaker and power cable connections.
Location FUNCTION
Connector A Connector B
1 - Rear Right(+)---Purple
2 - Rear Right(-)---Purple/Black
3 - Front Right(+)---Grey
4 Battery 12V (+)/Yellow Front Right(-)---Grey/Black
5 Power Antenna/Blue Front Left(+)---White
6 - Front Left((-)---White/Black
7 Ignition/Red Rear Left(+)---Green
8 Ground/Black Rear Left(-)---Green/Black
Power antenna wire is intended for power supply of the antenna and for remote control of an additional
amplifier.
9
Parking wire connection
If Parking cable is connected to hand brake switch, the video display of the TFT monitor will be controlled by
driving status, system setup and input video sources. When the car is moving ahead, if the video disc is
played, the screen shows a warning message. The warning screen will prevent the driver from watching
images.
Reverse driving cable connection
If the rear view video camera is connected, the unit automatically switches to camera picture during reverse
driving. The unit returns to the original work mode after the reverse driving is done.
12
Remote controller
1. MODE button
2. POWER button
3. UP cursor button
4. BND/RDM button
5. ENTER button
6. LEFT cursor button
7. DOWN cursor button
8. EJECT button
9. PTY button
10. P.SCN/RPT button
11. SEEK-/ button
12. AF/TA button
13. OSD button
14. STOP/PBC button
15. Digit buttons
16. PLAY/PAUSE button
17. MUTE button
18. MENU button
19. SUB-T button
20. RIGHT cursor button
21. SETUP button
22. ANGLE button
23. INT button
24. VOL+ button 28. VOL- button
25. A-B/ZOOM button 29. AUDIO/GOTO button
26. SEL button 30. DUAL button
27. SEEK+/ button 31. TILT button
13
Changing the battery
1. Press the catch and at the same time pull out the battery tray (pic. 1).
2. Insert the 1 lithium battery, type CR2025 (3V) battery with the stamped
(+) mark facing upward. Insert the battery tray into the remote controller
(pic.2).
Warning:
Store the battery where children cannot reach. If a child accidentally swallows the battery, consult a
doctor immediately.
Do not recharge, short, disassemble or heat the battery or dispose it in a fire.
Do not expose or bring into contact the battery with other metallic materials. Doing this may cause the
battery to give off heat, crack or start a fire.
When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may give
off heat, crack or start a fire.
Please direct the Remote controller to the IR sensor of the front panel.
Pic. 1
Pic
. 2
14
General operations
Touch screen
Due to the touch screen, you can fulfill most functions not only by pressing buttons but also by touching the
options you need.
Turning the unit on/off
Press any button (except EJECT button) to switch the unit on. Press and hold POWER button on the panel or
PWR button on the RC to turn off the power.
Reset the unit
Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press reset
button on the unit with a pointed object (such as a ballpoint pen) to set the unit to initial state.
Note: When some errors occur on the display, you can also press reset button to resume to normal, and it
will erase the clock setting and some memorized functions.
Volume control
Press VOL+/VOL- buttons on the RC or on the unit to increase/decrease the sound level.
Setting the sound characteristics
Press SEL button to open the following menu:
1. Setting list. Touch a setting to select its adjustment.
2. Adjustment buttons. Touch them to adjust corresponding
setting.
3. Page selection buttons. Touch to select a menu page.
4. Return button. Touch to return to previous menu level.
Following settings are available for adjustment:
Page 1
Equalizer: Select Flat, Classic, Pop, Rock or DSP OFF equalizer
mode.
TA volume: Adjust the volume level for TA radio service.
15
Page 2
Bass: Adjust the low-frequency level.
Treble: Adjust the high-frequency level.
Balance: Adjust the balance between left and right channels.
Fader: Adjust the balance between front and left channels.
Page 3
Beep: Select ALL (beep is heard at any button pressing), 2ND (beep is heard when a button is pressed
and held) or OFF (no beep).
Loud: Selecting loudness ON will emphasize the low frequency output.
Subwoofer: set the subwoofer on or off.
Note: You can also press SEEK-/ and SEEK+/ on the RC to select menu pages; press UP/DOWN cursor
buttons to select a setting, press LEFT/RIGHT buttons to adjust the setting.
Mute function
Press MUTE button on the RC or PWR button on the unit to turn off the sound. Press the button again or
adjust volume to resume the sound output.
Mode selection
Repeatedly press MODE
button on the RC or on the
panel to select an
operation mode.
In any mode press MENU
button to display the Main
menu consisting of two
pages:
In the menu, touch the item of the mode you need to select the corresponding mode. Touch the arrow icon
in the right part of the screen to switch between the 2 menu pages.
Note: The DVD, USB and SD modes are only available when a disc, USB or SD/MMC card is inserted into the
unit.
16
Navigation (option)
To enable navigation mode, touch NAVI button in the main menu.
Insert Navigation memory card into the Memory card slot of the unit before enabling navigation mode. To
access the slot, open the front panel. The device will warn you if the memory card is not properly inserted
into the card slot.
For more details about operations with navigation program, please read the instruction manual to the
navigation software. You can download the quickstart guidance and full instruction manual for the
navigation program from the web site of the navigation software manufacturer.
Angle setting
Press repeatedly TILT button to adjust the desired angle of the monitor.
Note: Please do not adjust the monitor tilt manually, otherwise it can get damaged.
AV in jack
AV jack is intended to receive audio and video signals by connecting to external device.
Subwoofer
Connect a subwoofer to this unit using the Subwoofer output of this unit. For subwoofer operation an external
amplifier is required.
Dual zone function
DUAL - dual zone function enabling user to listen to radio or watch TV in the front zone, and at the same time
play audio or video from disc, USB or memory card.
For Dual zone an external monitor with is required having its own acoustic system and possibility of volume
adjustment.
Press DUAL button to select between C-DUAL (buttons perform operations for the current mode of the front
zone) or D-DUAL (buttons perform DVD functions).
17
System setup
When you select SETTING mode, the menu will be displayed, in which you
can touch any item to select corresponding setting page:
After selecting a menu page you can navigate in the menu by pressing
cursor buttons on the RC and confirm your selection by pressing ENTER
button on the RC. Menu subpages are selected by pressing SEEK-/ and
SEEK+/ buttons on the RC. Or touch the items on the screen to select
them.
Sound page
Sound setting is described in details in paragraph “Setting the sound characteristics” above.
Display page
Page 1
Brightness: adjust the display brightness.
Screen save: turn on/off the screensaver.
Page 2
Dual: Select ON or OFF the Dual zone function.
Key: Use buttons at FRONT (buttons perform operations for the current mode of the front zone) or REAR
(buttons perform DVD functions). This function is available only if ON is selected for DUAL.
Rear: Select signal source for rear zone.
Date and Time page
Date: set current year, month and date.
Time: set current time.
RDS and Radio page
Page 1
Stereo: Select STEREO (stereo reception mode) or MONO (mono reception). When the received stereo
signal is weak, switch to mono mode to improve the signal. The function is available only in FM bands.
18
DX: Select LOCAL (only local station reception) or DX (local and distant station reception). The function is
available only in FM bands.
TA: Seek/Alarm. In TA SEEK mode, the unit will seek for traffic announcement program when TA is
pressed; in TA ALARM mode, no TA/TP is displayed and the alarm is set off.
Page 2
EON TA: DX/Local. If you want to receive information from local stations only, select EON TA Local mode.
Otherwise, select EON TA DX mode.
REG: REG ON (the receiver accepts regional variants of the tuned station with REG icon turned on), and
REG OFF (the receiver ignores regional variants).
PI: Mute/Sound. PI sound refers to the reception noise when the AF function tries to scan alternative
frequency.
Retune: RETUNE refers to the time period the unit allows for radio scan when reception is interrupted.
“SHORT” represents a time period of 30 seconds and “LONG” represents a time period of 90 seconds.
Mask: DPI/ALL. During MASK DPI mode, the unit will mask only the AF which has different PI, this is the
default mode; during MASK ALL mode, the unit will mask the AF which has different PI and no RDS signal
with high field strength.
Page 3
Radio Area: Select the radio broadcast area (Europe/USA/ASIA/SOUTH AMERICA).
System page
In this menu you can see the current version information.
Calibration page
“Carefully press and hold stylus on the center of the target. Repeat as the target moves around the screen” is
displayed. Touch and hold the cross in each position until it moves to a different position. After repeating it 4
times, the calibration of the screen is complete; touch the screen anywhere to return to menu. The
calibration procedure is useful when some malfunction occur with the touch screen, and it needs adjustment.
19
Utilities
In the main menu touch UTIL item to go to utility menu consisting of Calculator and Calendar items. Touch an
item to go to correspondent function.
Calculator
When you select Calculator an interface will show in which you can perform basic arithmetical operations by
touching buttons on the screen including following:
MC memory numeric clear
MR memory numeric restore
C current numeric clear
MS numeric save memory
M+ add edit numeric to memory numeric
CE clear error
backspace back space
Touch arrow in the right upper corner to exit calculator.
Calendar
When you select Calendar an interface will show in which you can select year and month by touching arrow
icons. Touch arrow in the right upper corner to exit calendar.
20
Radio operations
User interface of Radio mode
When the unit is switched to Radio mode, the below touchable
user interface will be displayed on the display:
1. PTY button. Touch to enable/disable PTY function. In the
PTY list, touch a program type to start its search.
2. TA button. Touch to enable/disable TA function.
3. AF button. Touch to enable/disable AF function.
4. ST button. Touch to select stereo/mono reception mode.
5. Current band and frequency.
6. Touch to enable navigation mode.
7. Preset station button. Touch to select the station. Touch
and hold to save the current frequency under the preset
number.
8. LOC button. Touch to select local/distant station reception.
9. Mute button; touch to switch sound on/off.
10. Volume down button. Touch to decrease volume.
11. Volume level.
12. Volume up button. Touch to increase volume.
13. BAND button. Touch to select bands.
14. AS/PS button. Touch to scan all saved stations in current band. Touch and hold to find and save 6
available stations in current band.
15. button. Touch for automatic search of the nearest station downwards.
16. button. Touch repeatedly to change frequency step by step downwards.
17. button. Touch repeatedly to change frequency step by step upwards.
18. button. Touch for automatic search of the nearest station upwards.
Band selection
Press BAND/RDM button on the RC to switch to the bands in the following order: FM1 - FM2 - FM3 - MW1 -
MW2.
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/