Mitsubishi Electric α2 Series Инструкция по применению

ENG

GER

FRE

ITL

ESP

SWE

RUS

α

2 Simple Application Controller

HARDWARE MANUAL

HARDWARE-HANDBUCH

MANUEL DU MATÉRIEL

MANUALE HARDWARE

MANUAL DE HARDWARE

MASKINVARUHANDBOK

РУКОВОДСТВО ПО АППАРАТНОЙ ЧАСТИ

α

2 Simple Application Controllers

Foreword

• This manual contains text, diagrams and explanations which will guide the reader in the correct

programming and operation of the α/α2 series controller.

• Before attempting to install or use the α/α2 Series Controller this manual should be read and understood.

• If in doubt at any stage of the installation of the α/α2 Series Controller always consult a professional

electrical engineer who is qualified and trained to local and national standards which apply to the installation

site.

• If in doubt about the operation or use of the α/α2 Series Controller please consult your local Mitsubishi

Electric representative.

• If the equipment is used in a manner not specified by the manufacturer, the protection provided by the

equipment may be impaired.

• Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that

may arise as a result of the installation or use of this equipment.

• All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not

to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on

these illustrative examples.

• Please contact a Mitsubishi Electric distributor for more information concerning applications in life critical

situations or high reliability.

• This manual is subject to change without notice.

2005 MITSUBISHI ELECTRIC CORPORATION

This manual confers no industrial property rights or any rights of any other kind, nor does it confer

any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems

involving industrial property rights which may occur as a result of using the contents noted in this

manual.

ENG-i

ENG

α2 Simple Application Controller

Hardware Manual

Manual number: JY992D97301

Manual revision: N

Date: 4/2018

α

2 Simple Application Controllers

α

2 Simple Application Controllers

ENG-ii

α

2 Simple Application Controllers

ENG-iii

ENG

Guidelines for the Safety of the User and Protection of equipment

This manual provides information for the use of the α2 Series Controllers. The manual has

been written to be used by trained and competent personnel. The definition of such a person

or persons is as follows;

a) Any engineer who is responsible for the planning, design and construction of automatic

equipment using the product associated with this manual should be of a competent

nature, trained and qualified to the local and national standards required to fulfill that

role. These engineers should be fully aware of all aspects of safety with regards to

automated equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and

qualified to the local and national standards required to fulfill that job. These engineers

should also be trained in the use and maintenance of the completed product. This

includes being completely familiar with all associated documentation for the said

product. All maintenance should be carried out in accordance with established safety

practices.

c) All operators of the completed equipment (See Note) should be trained to use that

product in a safe manner in compliance to established safety practices. The operators

should also be familiar with documentation which is connected with the actual operation

of the completed equipment.

Note : The term ‘completed equipment’ refers to a third party constructed device which

contains or uses the product associated with this manual.

For cleaning, perform dry wiping without using chemicals.

Notes on the Symbols Used in this Manual

At various times through out this manual certain symbols will be used to highlight points of

information which are intended to ensure the users personal safety and protect the integrity of

equipment. Whenever any of the following symbols are encountered its associated note must

be read and understood. Each of the symbols used will now be listed with a brief description of

its meaning.

Hardware Warnings

1) Indicates that the identified danger WILL cause physical and property damage.

2) Indicates that the identified danger could POSSIBLY cause physical and property

damage.

3) Indicates a point of further interest or further explanation.

Software Warnings

4) Indicates special care must be taken when using this element of software.

5) Indicates a special point which the user of the associate software element should

be aware of.

6) Indicates a point of interest or further explanation.

α

2 Simple Application Controllers

ENG-iv

• Under no circumstances will Mitsubishi Electric be liable or responsible for any

consequential damage that may arise as a result of the installation or use of this equipment.

• All examples and diagrams shown in this manual are intended only as an aid to

understanding the text, not to guarantee operation. Mitsubishi Electric will accept no

responsibility for actual use of the product based on these illustrative examples.

• Please contact a Mitsubishi Electric distributor for more information concerning applications

in life criticalo situations or high reliability.

Further Information Manual Lists

~ Refer to these manuals.

{ Refer to this manual if necessary.

 Refer to the content of these manuals if necessary though it is included in

α2 Hardware

Manual.

Manual Name Manual No. Description

~

α2 Hardware Manual

(This manual)

JY992D97301

This manual contains hardware explanations for

wiring, installation and specification for the

α2

Series controllers.

~

α2 Programming Manual

JY992D97101

This manual contains instruction explanations for

the

α2 Series controllers.

{

α Software Manual

JY992D74001

This manual contains explanations of operation

of AL-PCS/WIN-E Programming Software.

{

α2 Series Communication

User’s Manual

JY992D97701

This manual contains explanations for the setup,

messaging, diagnostics, bit assignments, etc for

communications using the

α2 series controller.



α2 Series Installation Manual

JY992D97501

This manual contains installation explanations

for the

α2 Series controller.



AL2-4EX, AL2-4EX-A2,

AL2-4EYR, AL2-4EYT

Installation Manual

JY992D97401

This manual contains installation explanations

for the AL2-4EX, AL2-4EX-A2, AL2-4EYR and

AL2-4EYT extension module.



AL2-EEPROM-2

Hardware Manual

JY992D96801

This manual contains hardware explanations for

the AL2-EEPROM-2.



AL2-2DA

Installation Manual

JY997D09301

This manual contains installation explanations

for the AL2-2DA.



AL2-2PT-ADP

Installation Manual

JY997D09401

This manual contains installation explanations

for the AL2-2PT-ADP.



AL2-2TC-ADP

Installation Manual

JY997D09501

This manual contains installation explanations

for the AL2-2TC-ADP.



AL-232CAB

Hardware Manual

JY992D76001

This manual contains hardware explanations for

the AL-232CAB.



AL2-GSM-CAB

Hardware Manual

JY992D97201

This manual contains hardware explanations for

the AL2-GSM-CAB.



AL-ASI-BD, AL2-ASI-BD

Hardware Manual

JY992D81401

This manual contains hardware explanations of

wiring, installation and specification, etc. for AL-

ASI-BD and AL2-ASI-BD.

α

2 Simple Application Controllers

ENG-v

ENG

Abbreviations

The following definitions or abbreviations will be used throughout this manual.

• The AL-PCS/WIN-E software will be referred to as the VLS software or the programming

software.

• The

α2 Series Simple Application Controller may be referred to as the α2 series, the α2

series controller or the main module.

• Function Blocks may be referred to as FB(s).

• Function Block Diagram may be referred to as FBD.

• Input/Output may be referred to as I/O.

• Personal Computer may be referred to as PC

• Microsoft Windows

®

, Windows

®

95, Windows

®

98, Windows

®

Me, WindowsNT

®

Workstation 4.0, Windows

®

2000, Windows

®

XP and Windows Vista

®

may be referred to

generically as Windows.

Registration

• Microsoft Windows

®

, Windows

®

95, Windows

®

98, Windows

®

Me, WindowsNT

®

Workstation 4.0, Windows

®

2000, Windows

®

XP and Windows Vista

®

are either

registered trademarks or trademarks of Microsoft Corporation in the United States and/or

other countries.

• The company name and the product name to be described in this manual are the

registered trademarks or trademarks of each company.

α

2 Simple Application Controllers

ENG-vi

α

2 Simple Application Controllers

ENG-vii

ENG

Table of Contents

Guidelines of Safety...................................................................ENG-iii

1. Introduction......................................................................................ENG-1

1.1 Special Features of the α2 Series System.................................................... ENG-2

1.2 Available Models ........................................................................................... ENG-3

1.3 Dimensions and Each Part Name ................................................................. ENG-4

1.4 System Configuration .................................................................................... ENG-6

1.5 Version Up List .............................................................................................. ENG-7

1.6 Applicable Programming Software ................................................................ ENG-7

2. Specifications ..................................................................................ENG-8

2.1 Power Supply Specification ........................................................................... ENG-8

2.2 Input Specification ........................................................................................ ENG-9

2.3 Output Specification .................................................................................... ENG-11

2.4 General Specification .................................................................................. ENG-12

3. Installation .....................................................................................ENG-14

3.1 Installation Mounting Notes ......................................................................... ENG-14

3.2 DIN RAIL Mounting of Main Unit ................................................................. ENG-15

3.2.1 Installation ......................................................................................................... ENG-15

3.2.2 Remove ............................................................................................................. ENG-15

3.3 Direct Mounting of Main Unit ....................................................................... ENG-16

3.4 Install Extension Module(AL2-14MR-*,AL2-24MR-*)................................... ENG-17

4. Wiring ............................................................................................ENG-18

4.1 Installation Wiring Notes.............................................................................. ENG-18

4.2 Wire Size ..................................................................................................... ENG-19

4.3 Power Supply .............................................................................................. ENG-20

4.4 AC Power Supply and Input Wiring ............................................................. ENG-21

4.4.1 AC Power Supply and Input Wiring ................................................................... ENG-21

4.4.2 AL2-4EX-A2 Input Wiring .................................................................................. ENG-21

4.5 DC Power Supply and Input Wiring ............................................................. ENG-22

4.5.1 DC Power Supply and Source (“+” Common) Input Wiring Diagram ................ ENG-22

4.5.2 AL2-4EX Source (“+” Common) Input Wiring Diagram ..................................... ENG-22

4.5.3 DC Power Supply and Sink (“-” Common) Input Wiring Diagram...................... ENG-23

4.5.4 AL2-4EX Sink (“-” Common) Input Wiring Diagram........................................... ENG-23

4.6 Output Relay and Transistor Wiring ............................................................ ENG-24

4.6.1 Relay Output Wiring Diagram main unit (AC and/or DC) .................................. ENG-24

4.6.2 Relay Output Wiring Diagram AL2-4EYR (AC and/or DC)................................ ENG-25

4.6.3 Transistor Output (Source or “+” Common Only) Wiring Diagram AL2-4EYT... ENG-26

5. Terminal Layout............................................................................ENG-27

6. AL2-EEPROM-2 ............................................................................ENG-30

6.1 Installation ................................................................................................... ENG-31

α

2 Simple Application Controllers

ENG-viii

7. AL-232CAB ...................................................................................ENG-32

7.1 Introduction.................................................................................................. ENG-32

7.1.1 External Dimensions ......................................................................................... ENG-32

7.2 Connected to AL-232CAB cable.................................................................. ENG-33

8. AL2-GSM-CAB ..............................................................................ENG-36

8.1 Introduction.................................................................................................. ENG-36

8.1.1 External Dimensions ......................................................................................... ENG-36

8.1.2 System Configuration with using AL2-GSM-CAB.............................................. ENG-37

8.2 Installation ................................................................................................... ENG-38

8.3 Remote Maintenace with a Modem ............................................................. ENG-40

8.3.1 Recommended Modems ................................................................................... ENG-40

8.3.2 RS-232C Straight Cable Between Modem and AL2-GSM-CAB........................ ENG-40

8.3.3 Modem Setting .................................................................................................. ENG-41

9. AL2-ASI-BD (AL2-14MR-*, AL2-24MR-* ).....................................ENG-44

9.1 Introduction.................................................................................................. ENG-44

9.1.1 External Dimensions ......................................................................................... ENG-44

9.1.2 System Configuration ........................................................................................ ENG-45

9.2 Specifications .............................................................................................. ENG-45

9.3 Wiring & Installation..................................................................................... ENG-46

9.3.1 Installation ......................................................................................................... ENG-46

9.3.2 Wiring ................................................................................................................ ENG-47

9.4 Slave Address Setting & Diagnostics .......................................................... ENG-47

9.4.1 Setting Slave Address ....................................................................................... ENG-47

9.4.2 Applicable Error checks..................................................................................... ENG-47

10.DCF77 Radio Clock......................................................................ENG-48

10.1 Introduction.................................................................................................. ENG-48

10.2 System Configuration .................................................................................. ENG-49

10.3 Specifications .............................................................................................. ENG-49

10.4 Wiring .......................................................................................................... ENG-50

10.4.1 Wiring ................................................................................................................ ENG-50

10.4.2 DCF77 Setup from

α2 display .......................................................................... ENG-51

10.4.3 Automatically Start ............................................................................................ ENG-52

10.4.4 Automatically Stop............................................................................................. ENG-52

10.4.5 Verification of Received Time............................................................................ ENG-52

11.AL2-2DA (AL2-14MR-*, AL2-24MR-*)..........................................ENG-54

11.1 Introduction.................................................................................................. ENG-55

11.1.1 External Dimensions ......................................................................................... ENG-55

11.1.2 System Configuration ........................................................................................ ENG-55

11.2 Specification ................................................................................................ ENG-56

11.3 Wiring & Installation..................................................................................... ENG-57

11.3.1 Installation ......................................................................................................... ENG-57

11.3.2 Wiring ................................................................................................................ ENG-58

11.3.3 Applicable Error checks..................................................................................... ENG-59

α

2 Simple Application Controllers

ENG-ix

ENG

12.AL2-2PT-ADP...............................................................................ENG-60

12.1 Introduction.................................................................................................. ENG-61

12.1.1 External Dimensions ......................................................................................... ENG-61

12.2 System Configuration .................................................................................. ENG-61

12.3 Specification ................................................................................................ ENG-62

12.4 Wiring and Installation ................................................................................. ENG-64

12.4.1 Installation ......................................................................................................... ENG-64

12.4.2 Wiring ................................................................................................................ ENG-65

12.4.3 Choosing a Temperature Scale......................................................................... ENG-66

12.4.4 Offset Adjustment.............................................................................................. ENG-67

12.4.5 Gain Adjustment................................................................................................ ENG-68

12.4.6 Fine Offset Adjust.............................................................................................. ENG-70

12.4.7 Applicable Error checks..................................................................................... ENG-71

13.AL2-2TC-ADP ..............................................................................ENG-72

13.1 Introduction.................................................................................................. ENG-73

13.1.1 External Dimensions ......................................................................................... ENG-73

13.2 System Configuration .................................................................................. ENG-73

13.3 Specification ................................................................................................ ENG-74

13.4 Wiring and Installation ................................................................................. ENG-76

13.4.1 Installation ......................................................................................................... ENG-76

13.4.2 Wiring ................................................................................................................ ENG-77

13.4.3 Choosing a Temperature Scale......................................................................... ENG-78

13.4.4 Offset Adjustment.............................................................................................. ENG-79

13.4.5 Gain Adjustment................................................................................................ ENG-80

13.4.6 Fine Offset Adjust.............................................................................................. ENG-82

13.4.7 Applicable Error Checks.................................................................................... ENG-83

14.Key, System Bit and Function Block Lists ....................................ENG-84

14.1 Key Lists ...................................................................................................... ENG-84

14.2 System Bit Lists ........................................................................................... ENG-85

14.2.1 System Bit Lists................................................................................................. ENG-85

14.2.2 Control Bit Lists ................................................................................................. ENG-86

14.3 Function Block Lists..................................................................................... ENG-87

15.Diagnostics...................................................................................ENG-91

15.1 Input Status Error ........................................................................................ ENG-92

15.2 Output Status Error...................................................................................... ENG-92

15.3 TOP MENU is not Displayed ....................................................................... ENG-93

15.4 Cannot enter Run Mode. ............................................................................. ENG-94

15.5 Incorrect Clock Data .................................................................................... ENG-94

15.6 The “?” appears on the Display ................................................................... ENG-94

15.7 Cannot Use an Operation Key..................................................................... ENG-95

15.8 Incorrect LCD display .................................................................................. ENG-96

15.9 Memory Cassette Is Not Working Correctly................................................. ENG-96

15.10Cannot Communicate with the AS-interface Master Module ...................... ENG-97

15.11Cannot Communicate with AL-PCS/WIN-E. ............................................... ENG-98

α

2 Simple Application Controllers

ENG-x

Introduction 1

ENG-1

ENG

1. Introduction

The α2 series can be easily used in all places where control is needed for the home, office, or

factory. The controller outputs cycle ON/OFF to control electrical equipment per the Function

Block program.

The explanation of the instructions and the operation of main unit can be found in

α2

Programming Manual. An explanation of the AL-PCS/WIN-E programming software can be

found in the

α Series Software Manual.

Applications

The

α2 series is designed to be used in automatic applications including those listed below.

- Automation of lights, air-conditioning, or watering systems

- The opening and shutting of gates

- Easy security systems

- Domestic animal and pet food distribution systems

- Control of stockyards and greenhouses

However, the

α2 series is not designed to be used in the following applications. Please contact

your local Mitsubishi Electric representative for more information.

- Applications where high reliabilities such as nuclear power control, railway facilities,

airline facilities, vehicles, combustion equipment, and medical equipment are required.

- Applications in life critical situations.

α

2 Simple Application Controllers

α

2 Simple Application Controllers

Introduction 1

ENG-2

1.1 Special Features of the α2 Series System

1) Display message and Function Block data

The

α2 series can display the state of operation and the alarm on the LCD display as a

message. It can display the following contents by using the display function block. The

value of displayed timers and counters can be changed in the RUN mode.

- Total characters on LCD display: 12 characters × 4 lines

- Display Items: Message, value (current or set) of timer and counter, analog values, etc

2) The programming in the personal computer is fast and easy

The programming software AL-PCS/WIN-E for Windows can create and save programs.

The programming can be done using a pictorial method in which lines are used to connect

function blocks on a programming screen.

Direct programming using the

α2 controller front panel keys is also available.

3) LCD image send via GSM modem

The

α2 (AL2-14MR-*,AL2-24MR-*) series is able to send the LCD image as an E-mail

using a GSM modem. The user can monitor application status by accessing the diagnostic

message sent as an E-mail via GSM modem

4) Supports computer link using dedicated protocol

The

α2 (AL2-14MR-*,AL2-24MR-*)series supports computer link (dedicated protocol).

User-specific application software using computer link can change schedule data,

parameters within Function Blocks and provide condition monitoring of the application.

5) Enhancement of clock function

The weekly timer and the calendar timer function have many switches that can be set and

provide powerful time dependant control capabilities.

6) Analog input, 0 - 10V/0 - 500, -50

°C - 200°C (PT100), -50°C - 450°C (K-type thermocouple):

The DC input for the

α2 series can accept of 0 - 10V signals with a resolution of 0 - 500.

7) Analog output,

0 - 4000/0 - 10V, 0 - 2000/4 - 20mA:

The

α2 series can output voltage and current signals.

8) High speed counter, Max. 1kHz

The

α2 series has high speed counters (Max. 2 points) when using AL2-4EX (EI1, EI2).

9) High current output capability

10)Built-in EEPROM

The built in EEPROM eliminates the need for battery backed data.

11)Supports 7 languages:

The

α2 series supports 7 languages (English, German, French, Italian, Spanish, Swedish,

and Russian

*1

). The displayed language can be selected in the TOP MENU.

*1 V3.00 or later

Table 1.1: High Current Output Capability

Output Type Capability

Relay

AL2-10MR-*: O01 - O04

AL2-14MR-*: O01 - O06

AL2-24MR-*: O01 - O04

8A/Common

AL2-24MR-*: O05 - O09

AL2-4EYR: EO1 - EO4

2A/Point (4A/Common)

Transistor AL2-4EYT: EO1 - EO4 1A/Point

α

2 Simple Application Controllers

Introduction 1

ENG-3

ENG

1.2 Available Models

*1 Without extension modules.

0

*1 When using AL2-2DA, AL2-2PT-ADP or AL2-2TC-ADP, α2 main module must be V2.00

or later.

Table 1.2:Main Units

Model

Power

Supply

Input Output

Dimensions

mm (inches)

MASS

(Weight)

kg (lbs)

Type Number Type Number

AL2-10MR-A

100 - 240V

AC~

100 - 240V

AC~

6RELAY4

71.2 x 90 x 52

(2.8 x 3.54

x 2.05)

0.21

(0.47)

AL2-10MR-D 24V DC

24V DC

Sink/Source

6RELAY4

0.20

(0.44)

AL2-14MR-A

100 - 240V

AC~

100 - 240V

AC~

8RELAY6

124.6 x 90 x 52

(4.91 x 3.54

x 2.05)

0.30

*1

(0.66)

AL2-14MR-D 24V DC

24V DC

Sink/Source

8RELAY6

AL2-24MR-A

100 - 240V

AC~

100 - 240V

AC~

15 RELAY 9

0.35

*1

(0.77)

AL2-24MR-D 24V DC

24V DC

Sink/Source

15 RELAY 9

0.30

*1

(0.66)

Table 1.3:Extension Modules/Adapters

Model

Input Output MASS

(Weight)

kg (lbs)

Type Number Type Number

AL2-4EX-A2 220 - 240V AC~ 4 ⎯

0.05

(0.11)

AL2-4EX

24V DC, Sink/

Source

4 ⎯

AL2-4EYR ⎯ RELAY 4

AL2-4EYT ⎯ TRANSISTOR 4

AL2-ASI-BD AS-interface Input 4 AS-interface Output 4

AL2-2DA

*1

⎯

Analog

(“0 to 10V” or “4 to 20mA”)

2

AL2-2PT-ADP

*1

PT100 Sensor 2 Analog (0 to 10V) 2

AL2-2TC-ADP

*1

Thermocouple

Sensor (K Type)

2 Analog (0 to 10V) 2

α

2 Simple Application Controllers

Introduction 1

ENG-4

1.3 Dimensions and Each Part Name

Figure 1.1: Each Part Name(AL2-10MR-*)

Nameplate printing

is a mark that instructs to use the cable with an appropriate temperature rating

(80°C or more) for wiring.

Figure 1.2: Each Part Name(AL2-14MR-*,AL2-24MR-*)

Nameplate printing

is a mark that instructs to use the cable with an appropriate temperature rating

(80°C or more) for wiring.

OUT4OUT2 OUT3

OUT1

AL2-10MR-D

OK

ESC

+

-

1

23456

DC INPUT

-

(B)(A)

RELAY OUTPUT

90 (3.54")

71.2 (2.8")

6 (0.24")

4 (0.16")

6 (0.24")

52 (2.05")

Nameplate

90 (3.54")

124.6 (4.91")

4 (0.16")

6 (0.24")

52 (2.05")

α

2 Simple Application Controllers

Introduction 1

ENG-5

ENG

Note;

• Refer to chapter 7 about dimensions of the AL-232CAB

• Refer to chapter 8 about dimensions of the AL2-GSM-CAB.

• Refer to chapter 9 about dimensions of the AL2-ASI-BD.

• Refer to chapter 11 about dimensions of the AL2-2DA.

• Refer to chapter 12 about dimensions of the AL2-2PT-ADP.

• Refer to chapter 13 about dimensions of the AL2-2TC-ADP.

Figure 1.3: Dimensions (AL2-4EX, AL2-2EX-A2, AL2-4EYR, AL2-4EYT)

Nameplate printing

is a mark that instructs to use the cable with an appropriate temperature rating

(80°C or more) for wiring.

Table 1.4: Each Part Name

Ref. Item Description

1 Mounting hole, φ4.2 mm

2 Power terminals

3 Input terminals

4 Mounting screw for the extension cover or extension module

5 Extension cover or extension module(AL2-14MR-*,AL2-24MR-*)

6 Groove for DIN rail mounting (Width of DIN rail 35mm <DIN EN 50022>)

7 DIN-RAIL mounting clips

8 Output terminals

9 Operation keys

10 Liquid crystal display

11 Programming port cover

Nameplate

Unit: mm (inches)

24.5 (0.96")

53.1 (2.09")

90 (3.54")

α

2 Simple Application Controllers

Introduction 1

ENG-6

1.4 System Configuration

Figure 1.4: System Configuration(AL2-10MR-*)

Figure 1.5: System Configuration(AL2-14MR-*,AL2-24MR-*)

*1 Further information can be found in chapter 8.

Table 1.5: System Configuration

Item Using Cable

1 AL-232CAB

2 AL2-GSM-CAB

3

RS-232C cross cable

*1

4

RS-232C straight cable for the modem

*1

5 RS-232C straight cable for the modem (specified by Modem manufacturer)

α

2

Series

c

Personal computer

- Programming Software

(AL-PCS/WIN-E)

Standard Connection to the Programming Softoware

α

2

Series

GSM

Modem

Remote Maintenance (via Telephone Line)

Remote Maintenance, e-Mail (via GSM)

de

fg

d

c

g

Personal computer

- Programming Software

(AL-PCS/WIN-E)

- Dedicated protocol

- e-Mail application

Cellular Phone

(Supporting SMS message)

Normal Modem Normal Modem

Normal Modem

Sending SMS Message

Using Dedicated Protocol

Standard Connection to the Programming Softoware

α

2 Simple Application Controllers

Introduction 1

ENG-7

ENG

1.5 Version Up List

1.6 Applicable Programming Software

Note;

• AL-PCS/WIN-E versions lower than V2.00, do not communicate with the α2 series.

• AL-PCS/WIN-E versions lower than V2.30, do not use the AL2-2DA, AL2-2PT-ADP or

AL2-2TC-ADP.

Table 1.6: History of

α2 Series

Version Description

V1.00 First product

V2.00

Supports the following points.

• AL2-2DA, AL2-2PT-ADP, AL2-2TC-ADP modules

• New function blocks

AO [Analog output] and PID [PID control]

• DCF77 Radio clock

V2.20

Supports the following points.

• New function blocks

SMR[Short Message Receiving] and CD[Call Detect]

• Enhanced User Program Protection

• Enhanced Daylight Saving Time Setup

• Enhanced Dedicated Protocol Communication

• GSM SIM PIN

• Modem Initialization String

V3.00

Supports the following points.

• Hour Meter backs up by EEPROM (No.197 - 200)

• Display Buffer Read by Dedicated Protocol

• Russian language addition

Table 1.7: Applicable Programming Software

α2 Version

Programming Software (AL-PCS/WIN-E) Version

V1.00 V2.00 or later

V2.00 V2.30 or later

V2.20 V2.40 or later

V3.00 V2.50 or later

α

2 Simple Application Controllers

Specifications 2

ENG-8

2. Specifications

Note;

• Refer to chapter 9 about specification of the AL2-ASI-BD.

• Refer to chapter 11 about specification of the AL2-2DA.

• Refer to chapter 12 about specification of the AL2-2PT-ADP.

• Refer to chapter 13 about specification of the AL2-2TC-ADP.

2.1 Power Supply Specification

Table 2.1: Power Supply Specifications

Description Code Specification

Power Supply

AL2-***-A 100 - 240V AC~, +10% -15%, 50/60 Hz

AL2-***-D 24V DC, +20% -15%

Maximum Momentary Power

Failure

AL2-***-A 10ms

AL2-***-D 5ms

In-rush Current

AL2-***-A,

240V AC~ (120V AC~)

≤ 6.5 A (3.5 A) < 5ms

AL2-***-D, 24V DC ≤ 7.0 A

Maximum Power

Consumption

AL2-10MR-A, 264V AC~ 4.9 W

AL2-10MR-D, 28.8V DC 4.0 W

AL2-14MR-A, 264V AC~ 5.5 W

AL2-14MR-D, 28.8V DC 7.5 W

AL2-24MR-A, 264V AC~ 7.0 W

AL2-24MR-D, 28.8V DC 9.0 W

Typical Power Consumption

(without Special Connection

Modules)

AL2-10MR-A, 240V AC~ I/O all On - 3.5 W; I/O all Off - 1.85 W

AL2-10MR-A, 120V AC~ I/O all On - 3.0 W; I/O all Off - 1.55 W

AL2-10MR-D, 24V DC I/O all On - 2.5 W; I/O all Off - 0.75 W

AL2-14MR-A, 240V AC~ I/O all On - 4.5 W; I/O all Off - 2.0 W

AL2-14MR-A, 120V AC~ I/O all On - 3.5 W; I/O all Off - 1.5 W

AL2-14MR-D, 24V DC I/O all On - 4.0 W; I/O all Off - 1.0 W

AL2-24MR-A, 240V AC~ I/O all On - 5.5 W; I/O all Off - 2.5 W

AL2-24MR-A, 120V AC~ I/O all On - 4.5 W; I/O all Off - 2.0 W

AL2-24MR-D, 24V DC I/O all On - 5.0 W; I/O all Off - 1.0 W

Fuse

AL2-***-A

AL2-10MR-D

Rating: 250 V 1 A

Type: Time Lag

AL2-14MR-D

AL2-24MR-D

Rating: 250 V 500 mA

Type: Time Lag

Страница загружается...

Mitsubishi Electric α2 Series Инструкция по применению

Похожие модели бренда

Модели других брендов