Electrolux ESI65010X Руководство пользователя

Бренд: Electrolux

Модель: ESI65010X

Категория: Посудомоечные машины

Тип: Руководство пользователя

user manual

upute za uporabu

Инструкция по

эксплуатации

dishwasher

perilica posuđa

посудомоечная машина

ESI 65010

Electrolux. Thinking of you.

Share more of our thinking at www.electrolux.com

Contents

Safety information 2

Product description 3

Control panel 4

First use 5

Set the water softener 5

Use of dishwasher salt 6

Use of rinse aid 7

Daily use 8

Load cutlery and dishes 9

Use of detergent 11

Select and start a washing programme

Unloading the dishwasher 14

Washing programmes 14

Care and cleaning 15

What to do if… 16

Technical data 17

Hints for test institutes 18

Installation 19

Water connection 19

Electrical connection 21

Environment concerns 21

Subject to change without notice

Safety information

In the interest of your safety and to en-

sure the correct use, before installing

and first using the appliance, read this

user manual carefully, including its hints

and warnings. To avoid unnecessary

mistakes and accidents, it is important

to ensure that all people using the appli-

ance are thoroughly familiar with its op-

eration and safety features. Save these

instructions and make sure that they re-

main with the appliance if it is moved or

sold, so that everyone using it through

its life will be properly informed on appli-

ance use and safety.

Correct use

• This dishwasher is only intended for wash-

ing household utensils suitable for ma-

chine washing.

• Do not put any solvents in the dishwasher.

This could cause an explosion.

• Knives and other items with sharp points

must be loaded in the cutlery basket with

their points down or placed in a horizontal

position in the upper basket.

• Only use products (detergent, salt and

rinse aid) suitable for dishwashers.

• Avoid opening the door whilst the appli-

ance is in operation, hot steam may es-

cape.

• Do not take any dishes out of the dish-

washer before the end of the washing cy-

cle.

• After use, isolate the appliance from the

power supply and turn off the water sup-

ply.

• This product should be serviced only by an

authorized service engineer, and only gen-

uine spare parts should be used.

• Under no circumstances should you at-

tempt to repair the machine yourself. Re-

pairs carried out by inexperienced persons

could cause injury or serious malfunction-

ing. Contact your local Service Force Cen-

tre. Always insist on genuine spare parts.

General safety

• Persons (including children) with reduced

physical sensory, mental capabilities or

lack of experience and knowledge must

not use the appliance. They must have su-

pervision or instruction for the operation of

the appliance by a person responsible for

their safety.

• Dishwasher detergents can cause chemi-

cal burns to eyes, mouth and throat. Could

endanger life! Comply with the safety in-

structions of the dishwasher detergent

manufacturer.

2 electrolux

• Water in the dishwasher is not for drinking

purposes. Detergent residue may still be

present in your machine.

• Ensure that the door of the dishwasher is

always closed when it is not being loaded

or unloaded. In this way you will avoid any-

body tripping over the open door and hurt-

ing themselves.

• Do not sit or stand on the open door.

Child safety

• This appliance is designed to be operated

by adults. Children must be supervised to

ensure that they do not play with the ap-

pliance.

• Keep all packaging well away from chil-

dren. There is a risk of suffocation.

• Keep all detergents in a safe place out of

children’s reach.

• Keep children well away from the dish-

washer when the door is open.

Installation

• Check your dishwasher for any transport

damage. Never connect a damaged ma-

chine. If your dishwasher is damaged con-

tact your supplier.

• All packaging must be removed before

use.

• Any electrical and plumbing work required

to install this appliance must be carried out

by a qualified and competent person.

• For safety reasons it is dangerous to alter

the specifications or attempt to modify this

product in any way.

• Never use the dishwasher if the electrical

supply cable and water hoses are dam-

aged; or if the control panel, work top or

plinth area are damaged such that the in-

side of the appliance is freely accessible.

Contact your local Service Force centre, in

order to avoid hazard.

• All sides of the dishwasher must never be

drilled to prevent damage to hydraulic and

electric components.

Warning! For electrical and water

connection carefully follow the

instructions given in the specific

paragraphs.

Product description

1 Upper basket

2 Water hardness dial

3 Salt container

4 Detergent dispenser

5 Rinse aid dispenser

6 Rating plate

electrolux 3

7 Filters

8 Lower spray arm

9 Upper spray arm

Control panel

1. On/Off button

2. Programme selection buttons

3. Delay start button

4. Digital display

5. Indicator lights

6. Function buttons

The digital display

The digital display shows:

• the countdown for the delay start,

• if the appliance is in setting mode,

• if a washing programme is set.

Function buttons

The following functions can be set using

these buttons:

• setting the water softener level,

• cancelling a washing programme or a de-

lay start in progress,

• activation/deactivation of the Multitab

function,

• activation/deactivation of the rinse aid dis-

penser when Multitab function is active.

Indicator lights

Programme in progress Comes on when a washing programme is set and

remains on for all the duration of the washing pro-

gramme.

Goes off when the washing programme has

ended.

4 electrolux

Indicator lights

End Comes on when a washing programme has

ended. It also has added functions of visual sig-

nalling as:

– the setting of the water softener,

– activation/deactivation of the rinse aid dispens-

er,

– intervention of an alarm due to the malfunction

of the machine.

Multitab function Indicates the activation/deactivation of the 'Multi-

tab function' ( refer to 'Multitab function' ).

Salt

Comes on when the special salt has run out.

Rinse aid

Comes on when the rinse aid has run out.

1) The salt and rinse aid indicator lights are never on while a washing programme is running even if filling

with salt and/or rinse aid is necessary.

Setting mode

Press the On/Off button. If ALL programme

button lights come on and the digital display

shows 3 horizontal bars, the appliance is in

setting mode.

Always remember that when performing

the following operations:

– selecting a washing programme,

– setting the water softener level,

– activating/deactivating the rinse aid,

the appliance MUST be in setting mode.

Press the On/Off button. If a programme but-

ton light comes on and the digital display

shows 1 horizontal bar, the last performed or

selected programme is still set. In this case,

to return to setting mode, the programme

has to be cancelled.

To cancel a set programme or a

programme in progress

Simultaneously press and hold the two Can-

cel buttons ( CANCEL ) (function buttons

B and C ) until all the programme button

lights come on and the digital display shows

3 horizontal bars. The programme has been

cancelled and the machine is now in setting

mode.

First use

Before using your dishwasher for the first

time:

• Ensure that the electrical and water con-

nections comply with the installation in-

structions

• Remove all packaging from inside the ap-

pliance

• Set the water softener level

• Pour 1 litre of water into the salt container

and then fill with dishwasher salt

• Fill the rinse aid dispenser

If you want to use combi detergent

tablets such as: ''3 in 1'', ''4 in 1'', ''5

in 1'' etc... set the Multitab function.

(See ''Multitab function'').

Set the water softener

The dishwasher is equipped with a water

softener designed to remove minerals and

salts from the water supply, which would

have a detrimental or adverse effect on the

operation of the appliance.

The higher the content of these minerals and

salts, the harder your water is. Water hard-

ness is measured in equivalent scales, Ger-

man degrees (dH°), French degrees (°TH)

and mmol/l (millimol per litre - international

unit for the hardness of water).

electrolux 5

The softener should be adjusted according

to the hardness of the water in your area.

Your local Water Authority can advise you on

the hardness of the water in your area.

The water softener must be set in two

ways: manually, using the water hard-

ness dial and electronically.

Water hardness Adjusting the water hardness setting Use of

salt

°dH °TH mmol/l manually electronically

51 - 70 91 - 125 9,1 - 12,5 2 level 10 yes

43 - 50 76 - 90 7,6 - 9,0 2 level 9 yes

37 - 42 65 - 75 6,5 - 7,5 2 level 8 yes

29 - 36 51 - 64 5,1 - 6,4 2 level 7 yes

23 - 28 40 - 50 4,0 - 5,0 2 level 6 yes

19 - 22 33 - 39 3,3 - 3,9 2 level 5 yes

15 - 18 26 - 32 2,6 - 3,2 1 level 4 yes

11 - 14 19 - 25 1,9 - 2,5 1 level 3 yes

4 - 10 7 - 18 0,7 - 1,8 1 level 2 yes

< 4 < 7 < 0,7 1 level 1 no

Setting manually

The dishwasher is factory set at position

1. Open the dishwasher door.

2. Remove the lower basket from the dish-

washer.

3. Turn the water hardness dial to position

1 or 2 (see chart).

4. Replace the lower basket.

Setting electronically

The dishwasher is factory set at level 5.

1. Press the On/Off button. The dishwasher

must be in setting mode.

2. Simultaneously press and hold function

buttons B and C , until the lights of func-

tion buttons A , B and C start flashing.

Press function button A , the lights of

function buttons B and C go off while the

light of function button A continues to

flash, at the same the End indicator light

starts to flash.

The current level is indicated by the num-

ber of flashes of the End indicator light.

Examples:

5 flashes, pause, 5 flashes, pause, etc. =

level 5

6 flashes, pause, 6 flashes, pause, etc. =

level 6

4. To change the level, press function but-

ton A . Each time the button is pressed

the level changes. (For the selection of the

new level see the chart).

Examples: If the current level is 5, by

pressing function button A once, level 6

is selected. if the current level is 10, by

pressing function button A once, level 1

is selected.

5. To memorize the operation, switch off the

dishwasher by pressing the On/Off but-

ton.

Use of dishwasher salt

Warning!

Only use salt specifically designed for use in

dishwashers. All other types of salt not spe-

6 electrolux

cifically designed for use in a dishwasher, es-

pecially table salt, will damage the water soft-

ener. Only fill with salt just before starting one

of the complete washing programmes. This

will prevent any grains of salt or salty water,

which may have been spilt, remaining on the

bottom of the machine for any period of time,

which may cause corrosion.

To fill:

1. Open the door, remove the lower basket

and unscrew the cap of the salt container

by turning it anticlockwise.

2. Pour 1 litre of water into the container

(this is necessary only before filling

with salt for the first time) .

3. Using the funnel provided, pour in the salt

until the container is full.

4. Replace the cap making sure that there

is no trace of salt on the screw thread or

on the gasket.

5. Replace the cap tightly turning it clock-

wise until it stops with a click.

Do not worry if water overflows from the

unit when filling with salt, this is quite

normal.

The salt indicator light on the control

panel can remain illuminated for 2-6

hours after the salt has been replen-

ished, assuming the dishwasher re-

mains switched on. If you are using

salt that takes longer to dissolve

then this can take longer. The oper-

ation of the machine is not affected.

Use of rinse aid

Warning! Only use branded rinse aid for

dishwashers.

Never fill the rinse aid dispenser with any

other substances (e.g. dishwasher

cleaning agent, liquid detergent). This

would damage the appliance.

Rinse aid ensures thorough rinsing, and

spot and streak free drying.

Rinse aid is automatically added during

the last rinse.

1. Open the container by pressing the re-

lease button (A).

2. Add the rinse aid in the container. The

maximum level for filling is indicated by

"max".

electrolux 7

The dispenser holds about 110 ml of rinse

aid, which is sufficient for between 16 and

40 washing cycles, depending upon the

dosage setting.

3. Ensure that the lid is closed after every

refill.

Clean up any rinse aid spilt during filling

with an absorbent cloth to avoid excess

foaming during the next wash.

According to the finish and drying results ob-

tained, adjust the dose of rinse aid by means

of the 6 position selector (position 1 minimum

dosage, position 6 maximum dosage).

The dose is factory set in position 4.

Increase the dose if there are drops of water

or lime spots on the dishes after washing.

Reduce it if there are sticky whitish streaks

on the dishes or a bluish film on glassware or

knife blades.

Daily use

• Check if it’s necessary to refill with dish-

washer salt or rinse aid.

• Load cutlery and dishes into the dishwash-

er.

• Fill with dishwasher detergent.

• Select a wash programme suitable for the

cutlery and dishes.

• Start the wash programme.

Helpful hints and tips

Sponges, household cloths and any object

that can absorb water may not be washed in

the dishwasher.

• Before loading the dishes, you should:

– Remove all left over food and debris.

– Soften remnants of burnt food in pans

• When loading the dishes and cutlery,

please note:

– Dishes and cutlery must not impede the

rotation of the spray arms.

– Load hollow items such as cups,

glasses, pans, etc. with the opening

downwards so that water cannot collect

in the container or a deep base.

– Dishes and items of cutlery must not lie

inside one another, or cover each other.

– To avoid damage to glasses, they must

not touch.

– Lay small objects in the cutlery basket.

• Plastic items and pans with non stick coat-

ings have a tendency to retain water

drops; these items will not dry as well as

porcelain and steel items.

• Light items (plastic bowls etc.) must be

loaded in the upper basket and arranged

so they do not move.

8 electrolux

For washing in the dishwasher the following cutlery and dishes

are not suitable: are of limited suitability:

• Cutlery with wooden, horn, china or mother-of-

pearls handles.

• Plastic items that are not heat resistant.

• Older cutlery with glued parts that are not tem-

perature resistant.

• Bonded cutlery items or dishes.

• Pewter or copper items.

• Lead crystal glass.

• Steel items prone to rusting.

• Wooden platters.

• Items made from synthetics fibres.

• Only wash stoneware in the dishwasher if it is

specially marked as being dishwasher-safe by

the manufacturer.

• Glazed patterns may fade if machine washed

frequently.

• Silver and aluminium parts have a tendency to

discolour during washing: Residues, e.g. egg

white, egg yolk and mustard often cause dis-

colouring and staining on silver. Therefore al-

ways clean left-overs from silver immediately, if

it is not to be washed straight after use.

Load cutlery and dishes

The lower basket

The lower basket is designed to take sauce-

pan, lids, plates, salad bowls, cutlery etc.

Service dishes and large lids should be ar-

ranged around the edge of the basket, en-

suring that the spray arms can turn freely.

The rows of prongs in the lower basket can

lie flat to allow you to load pots, pans and

bowls.

The cutlery basket

Long bladed knives stored in an upright

position are a potential hazard. Long

and/or sharp items of cutlery such as

carving knives must be positioned

horizontally in the upper basket. Take

care when loading or unloading sharp

items such as knives.

Forks and spoons should be placed in the

removable cutlery basket with the handles

facing downwards and the knives with their

handles facing upwards.

electrolux 9

If the handles protrude from the bottom of the

basket, obstructing the lower spray arm, load

the cutlery with the handles facing upwards.

Mix spoons with other cutlery to prevent

them from sticking together.

To make loading of the cutlery basket easier,

lower the cutlery basket handle.

For best results we recommend that you use

the cutlery grids.

If the size and dimensions of the cutlery do

not allow the use of the grids, they can be

easily hidden.

The cutlery basket is in two parts which can

be separated to give greater loading flexibili-

ty. To separate the two parts, slide them hor-

izontally in opposite directions and pull them

apart.

To reassemble, reverse the procedure.

The upper basket

The upper basket is designed for saucers,

salad bowls, cups, glasses, pots and lids.

Arrange items on and underneath the cup

racks so that water can reach all surfaces.

10 electrolux

Glasses with long stems can be placed up-

side down in the cup racks.

For taller items, the cup racks can be folded

upwards.

For glasses with long stems (according to the

size and dimensions), set the glass holder to

the left or right position.

Before closing the door, ensured that

the spray arms can rotate freely.

Adjusting the height of the upper basket

If washing very large plates you can load

them in the lower basket after moving the

upper basket to the higher position.

Maximum height of the dishes in the lower

basket

With upper basket

raised

31 cm

With upper basket

lowered

27 cm

To move to the higher position proceed

as follows:

1. Pull out the basket until it stops.

2. Carefully lift both sides upwards until the

mechanism is engaged and the basket is

stable.

To lower the basket to the original posi-

tion proceed as follows:

1. Pull out the basket until it stops.

2. Carefully lift both sides upwards and then

allow the mechanism to drop back down

slowly, keeping hold of it.

Never lift or lower the basket on one side

only

When the basket is in the higher position

cups cannot be placed on the cup racks.

After loading your machine always

close the door, as an open door can

be a hazard.

Use of detergent

Only use detergents specifically de-

signed for use in dishwashers.

Please observe the manufacturer’s dos-

ing and storage recommendations as

stated on the detergent packaging.

electrolux 11

Using no more than the correct amount

of detergent contributes to reducing pol-

lution.

Fill with detergent

1. Open the lid.

2. Fill the detergent dispenser (1) with de-

tergent. The marking indicates the dosing

levels:

20 = approximately 20 g of detergent

30 = approximately 30 g of detergent.

3. All programmes with prewash need an

additional detergent dose (5/10 g) that

must be placed in the prewash detergent

chamber (2).

This detergent will be used during the

prewash phase.

When using detergent tablets; place the

tablet in compartment (1)

4. Close the lid and press until it locks in

place.

Detergent tablets from different manu-

facturers dissolve at different rates. For

this reason, some detergent tablets do

not attain their full cleaning power during

short washing programmes. Therefore,

please use long washing programmes

when using detergent tablets, to ensure

the complete removal of detergent re-

siduals.

Select and start a washing programme

Select the washing programme and

delay start with the door slightly

opened. The start of the programme

or the countdown of the delay start

will occur only after the closure of

the door. Until then it is possible to

modify the settings

1. Check that the baskets have been loaded

correctly and that the spray arms are free

to rotate.

2. Check that the water tap is opened.

3. Press the On/Off button. The dishwasher

must be in setting mode.

4. Press the button corresponding to the re-

quired programme (refer to 'Washing

programmes' chart).

12 electrolux

When a programme has been selected

the corresponding light comes on.

The digital display shows 3 horizontal

bars.

The programme in progress indicator

light comes on.

Close the dishwasher door, the pro-

gramme starts automatically.

The programme in progress indicator

light remains on.

The digital display shows only 1 horizon-

tal bar and will remain on for all the dura-

tion of the washing programme.

Setting and starting the programme with

delay start

1. After having selected the washing pro-

gramme, press the delay start button until

the digital display shows the flashing

number of hours for the delay start. The

start of the selected washing programme

can be delayed for between 1 and 9

hours.

2. Close the dishwasher door, the count-

down starts automatically. The number in

the display is no longer flashing but fixed

with static light.

3. The countdown will decrease in steps of

1 hour.

4. Opening the door will interrupt the count-

down. Close the door; the countdown will

continue from the point at which it was

interrupted.

5. Once the delay start has elapsed the pro-

gramme will start automatically.

With the delay start function set, the

programme in progress indicator light

is off. Once the countdown of the delay

start has elapsed, the washing pro-

gramme will start automatically and the

programme in progress indicator light

will come on.

The selection of the washing pro-

gramme and delay start can occur also

with the door closed.

When you press a programme button

you have ONLY 3 seconds to select a

different programme or a delay start.

After these 3 seconds, the selected pro-

gramme starts automatically.

Warning! Interrupt or cancel a

washing programme in progress

ONLY if it's absolutely necessary.

Attention! Hot steam may escape

when the door is opened. Open the

door carefully.

Interrupt a washing programme in

progress

• Open the dishwasher door; the pro-

gramme will stop. Close the door; the pro-

gramme will start from the point at which

it was interrupted.

• Press the On/Off, all lights will go off. Press

the On/Off button again; the programme

will start from the point at which it was in-

terrupted.

Cancel a delay start or a washing

programme in progress

• Simultaneously press and hold the two

function buttons B and C until all the pro-

gramme lights come on and the digital dis-

play shows 3 horizontal bars.

• Cancelling a delay start will also cancel a

washing programme. You have to select

the washing programme again.

• If a new washing programme is to be se-

lected, check that there is detergent in the

detergent dispenser.

End of the washing programme

• The dishwasher will automatically stop and

the programme in progress indicator

light goes off.

•

The End indicator light comes on.

• The light of the programme just ended will

remain on.

• The digital display goes off.

1. Switch off the dishwasher by pressing the

On/Off button.

2. Open the dishwasher door, leave it ajar

and wait a few minutes before removing

the dishes; this way they will be cooler

and the drying will be improved.

electrolux 13

Unloading the dishwasher

• Hot dishes are sensitive to knocks. The

dishes should therefore be allowed to cool

down before removing from the appliance.

•Empty the lower basket first and then the

upper one; this will avoid water dripping

from the upper basket onto the dishes in

the lower one.

• Water may appear on the sides and the

door of the dishwasher as the stainless

steel will eventually become cooler than

the dishes.

When the washing programme has

finished, it is recommended that the

dishwasher is unplugged and the

water tap turned off.

Washing programmes

Programme Degree of soil Type of load Programme description

Intensive

Heavy soil

Crockery, cutlery,

pots and pans

Prewash

Main wash up to 70°C

2 intermediate rinses

Final rinse

Drying

Any

Crockery, cutlery,

pots and pans

Prewash

Main wash up to 45°C or 70°C

1 or 2 intermediate rinses

Final rinse

Drying

Quick

Normal or light

soil

Crockery and

cutlery

Main wash up to 60°C

Final rinse

Normal soil

Crockery and

cutlery

Prewash

Main wash up to 50°C

1 intermediate rinse

Final rinse

Drying

Glass

Normal soil

Delicate crockery

and glassware

Main wash up to 45°C

1 intermediate rinse

Final rinse

Drying

1) During the "Auto" washing programme the level of soiling on the dishes is determined by how cloudy

the water is. The programme duration, water and energy consumption levels can vary; this depends

upon if the appliance is fully or partially loaded and if the dishes are lightly or heavily soiled. The

temperature of the water is automatically adjusted between 45°C and 70°C.

2) Ideal for washing a partially loaded dishwasher. This is the perfect daily programme, made to meet

the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery.

3) Test programme for test institutes

Consumption values

Programme Programme duration

(in minutes)

Energy consumption

(in kWh)

Water consumption

(in litres)

Intensive 110 - 120 1,8 - 2,0 23 - 25

Auto 90 - 130 1,1 - 1,7 12 - 23

Quick 30 0,9 9

Eco

150 - 160 1,0 - 1,2 14 - 16

14 electrolux

Consumption values

Programme Programme duration

(in minutes)

Energy consumption

(in kWh)

Water consumption

(in litres)

Glass 60 - 70 0,8 - 0,9 14 - 15

1) Test programme for test institutes

The consumption values are intended as

a guide and depends on the pressure

and the temperature of the water and al-

so by the variations of the power supply

and the amount of dishes.

Care and cleaning

Cleaning the filters

The filters must be checked and cleaned

from time to time. Dirty filters will degrade the

washing result.

Warning! Before cleaning the filters

ensure that the machine is switched off.

1. Open the door, remove the lower basket.

2. The dishwasher filter system comprises a

coarse filter ( A ), a microfilter ( B ) and a

flat filter. Unlock the filter system using the

handle on the microfilter.

3. Turn the handle about 1/4 a turn anti-

clockwise and remove the filter system

Take hold of the coarse filter ( A ) by the

handle with the hole and remove from the

microfilter ( B ).

5. Clean all filters thoroughly under running

water.

6. Remove the flat filter from the base of the

washing compartment and clean both

faces thoroughly.

7. Put the flat filter back in the base of the

washing compartment and ensure that it

fits perfectly.

8. Place the coarse filter ( A ) in the microfil-

ter ( B ) and press together.

9. Put the filter combination in place and

lock by turning the handle clockwise to

the stop. During this process ensure that

the flat filter does not protrude above the

base of the washing compartment.

NEVER use the dishwasher without

filters. Incorrect repositioning and

fitting of the filters will produce poor

washing results and will result in

damage to the appliance.

NEVER try to remove the spray

arms.

If residues of soil have clogged the holes

in the spray arms, remove the debris

with a cocktail stick.

electrolux 15

External cleaning

Clean the external surfaces of the machine

and control panel with a damp soft cloth. If

necessary use only neutral detergents. Never

use abrasive products, scouring pads or sol-

vent (acetone, trichloroethylene etc...).

Internal cleaning

Ensure that the seals around the door, the

detergent and rinse aid dispensers are

cleaned regularly with a damp cloth.

We recommend every 3 months you run the

wash programme for heavy soiled dishes us-

ing detergent but without dishes.

Prolonged periods of non-operation

If you are not using the machine for a pro-

longed period of time you are advised to:

1. Unplug the appliance and then turn off

the water.

2. Leave the door ajar to prevent the forma-

tion of any unpleasant smells.

3. Leave the inside of the machine clean.

Frost precautions

Avoid placing the machine in a location

where the temperature is below 0°C. If this is

unavoidable, empty the machine, close the

appliance door, disconnect the water inlet

pipe and empty it.

Moving the machine

If you have to move the machine (moving

house etc...):

1. Unplug it.

2. Turn the water tap off.

3. Remove the water inlet and discharge

hoses.

4. Pull the machine out together with the

hoses.

Avoid over tilting the machine during trans-

portation.

What to do if…

The dishwasher will not start or stops during

operation.

Certain problems can be due to the lack of

simple maintenance or oversights, which can

be solved with the help of the hints described

in the chart, without calling out an engineer.

Switch off the dishwasher, open the door

and carry out the following suggested cor-

rective actions.

Fault codes and malfunction Possible cause and solution

• continuous flashing of the light of the running

programme

• 1 flash of the End indicator light

The dishwasher does not fill with water

• The water tap is blocked or furred with lime-

scale.

Clean the water tap.

• The water tap is turned off.

Turn the water tap on.

• The filter (where present) in the water inlet hose

is blocked.

Clean the filter.

• The water inlet hose has not been correctly laid

or it is kinked or squashed.

Check the water inlet hose connection.

• continuous flashing of the light of the running

programme

• 2 flashes of the End indicator light

The dishwasher will not drain

• The sink spigot is blocked.

Clean out the sink spigot.

• The water drain hose has not been correctly laid

or it is kinked or squashed.

Check the water drain hose connection.

• continuous flashing of the light of the running

programme

• 3 flashes of the End indicator light

Anti-flood device is activated

• Close the water tap and contact your local

Service Force Centre.

16 electrolux

Malfunction Possible cause and solution

The programme does not start

• The dishwasher door has not been properly

closed.

Close the door.

• The main plug is not plugged in.

Insert the main plug

• The fuse has blown out in the household fuse

box.

Replace the fuse.

• Delay start has been set.

If dishes are to be washed immediately, cancel

the delay start.

Once these checks have been carried out

switch on the appliance.

The programme will continue from the point

at which it was interrupted.

If the malfunction or fault code reappears

contact your local Service Force Centre.

For other fault codes not described in the

above chart, please contact your local Serv-

ice Force Centre.

Contact your local Service Force Centre,

quoting the model (Mod.), product number

(PNC) and serial number (S.N.).

This information can be found on the rating

plate located on the side of the dishwasher

door.

So that you always have these numbers at

hand, we recommend you to make a note of

them here:

Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The wash results are not satisfactory

The dishes are not

clean

• The wrong programme has been selected.

• The dishes are arranged in such a way as to stop water reaching all parts

of a surface. The baskets must not be overloaded.

• The spray arms do not rotate freely due to incorrect arrangement of the

load.

• The filters in the base of the washing compartment are dirty or incorrectly

positioned.

• Too little or no detergent has been used.

• Where there are limescales deposits on the dishes; the salt container is

empty or incorrect level of the water softener has been set.

• The drain hose connection is not correct.

• The salt container cap is not properly closed.

The dishes are wet

and dull

• Rinse aid was not used.

• The rinse aid dispenser is empty.

There are streaks,

milky spots or a blu-

ish coating on

glasses and dishes

• Decrease rinse aid dosage.

Water drops have

dried onto glasses

and dishes

• Increase rinse aid dosage.

• The detergent may be the cause. Contact the detergent manufacturer con-

sumer care line.

If after all these checks, the problem persists,

contact your local Service Force Centre.

Technical data

Dimensions Width

Height

Depth

59,6 cm

81,8 - 89,8 cm

57,5 cm

electrolux 17

Electrical connection - Voltage -

Overall power - Fuse

Information on the electrical connection is given on the rating plate

on the inner edge of the dishwasher door.

Water supply pressure Minimum

Maximum

0,05 MPa (0,5 bar)

0,8 MPa (8 bar)

Capacity 12 place settings

Weight 39,5 kg

Hints for test institutes

Testing in accordance with EN 60704 must

be carried out with appliance fully loaded and

using the test programme (refer to 'Washing

programmes').

Test in accordance with EN 50242 must be

carried out when the salt container and rinse

aid dispenser have been filled with salt and

rinse aid respectively and using the test pro-

gramme (refer to 'Washing programmes').

Full load: 12 standard place settings

Amount of detergent required: 5 g + 25 g (Type B)

Rinse aid setting position 4 (Type III)

Arrangement upper basket (take off the

glass holder)

Arrangement lower basket

Arrangement cutlery basket

18 electrolux

Installation

Warning! Any electrical and/or

plumbing work required to install

this appliance should be carried out

by a qualified electrician and/or

plumber or competent person.

Remove all packaging before positioning the

machine.

If possible, position the machine next to a

water tap and a drain.

This dishwasher is designed to be fitted un-

der a kitchen counter or work surface.

Attention! Carefully follow the instructions

on the enclosed template for building in the

dishwasher and fitting the furniture panel.

No further openings for the venting of the

dishwasher are required, but only to let the

water fill and drain hose and power supply

cable pass through.

The dishwasher incorporates adjustable feet

to allow the adjustment of the height.

During all operations that involve accessibility

to internal components the dishwasher has

to be unplugged.

When inserting the machine, ensure that the

water inlet hose, the drain hose and the sup-

ply cable are not kinked or squashed.

Fixing to the adjacent units

The dishwasher must be secured against tilt-

ing.

Therefore make sure that the counter it is

fixed under, is suitably secured to a fixed

structure (adjacent kitchen unit cabinets,

wall).

Levelling

Good levelling is essential for correct closure

and sealing of the door.

When the appliance is correctly levelled, the

door will not catch on either side of the cab-

inet .

If the door does not close correctly, loosen

or tighten the adjustable feet until the ma-

chine is perfectly level.

Water connection

Water inlet connection

This appliance can be connected to either a

hot (max. 60°) or cold water supply.

With a hot water supply you can have a sig-

nificant reduction of energy consumption.

This however, depends on how the hot water

is produced. (We suggest alternative sources

of energy that are more environmentally

friendly as e.g. solar or photovoltaic panels

and aeolian).

For making the connection itself, the cou-

pling nut fitted to the appliance water inlet

hose is designed to screw onto a 3/4" thread

spout or to a purpose made quick-coupling

tap such as the Press-block.

The water pressure must be within the limits

given in the 'Technical data'. Your local Wa-

ter Authority will advise you on the average

mains pressure in your area.

The water inlet hose must not be kinked,

crushed, or entangled when it is being con-

nected.

The appliance features inlet and drain hoses

which can be turned either to the left or the

right to suit the installation by means of the

locknut. The locknut must be correctly

fitted to avoid water leaks.

Attention! NOT all dishwasher models of

have inlet and drain hoses provided with

a locknut. In this case, this facility is not

available.

If the appliance is connected to new pipes or

pipes which have not been used for a long

time, you should run the water for a few mi-

nutes before connecting the inlet hose.

DO NOT use connection hoses which

have previously been used on an old ap-

pliance.

This appliance has been fitted with safe-

ty features which will prevent the water

used in the appliance from returning

back into the drinking water system. This

appliance complies with the applicable

plumbing regulations.

Water inlet hose with safety valve

After connecting the double-walled water in-

let hose, the safety valve is next to the tap.

Therefore the water inlet hose is only under

electrolux 19

pressure while the water is running. If the wa-

ter inlet hose starts to leak during this oper-

ation, the safety valve cuts off the running

water.

Please take care when installing the water

inlet hose:

• The electrical cable for the safety valve is

in the double-walled water inlet hose. Do

not immerse the water inlet hose or the

safety valve in water.

• If water inlet hose or the safety valve is

damaged, remove the mains plug imme-

diately.

• A water inlet hose with safety valve must

only be replaced by the Service Force

Centre.

Warning! Dangerous voltage

Water drain connection

The end of the drain hose can be connected

in the following ways:

1. To the sink outlet spigot, securing it to the

underside of the work surface. This will

prevent waste water from the sink run-

ning into the machine.

2. To a stand pipe provided with venthole,

minimum internal diameter 4 cm.

The waste connection must be at a maxi-

mum height of 60 cm from the bottom of the

dishwasher.

The drain hose can face either to the right or

left of the dishwasher

Ensure the drain hose is not bent or squash-

ed as this could prevent or slow down the

discharge of water.

The sink plug must not be in place when the

machine is draining as this could cause the

water to syphon back into the machine.

The total length of the drain hose, including

any extension you might add, must be no

longer than 4 metres. The internal diameter

of the extension hose must be no smaller

than the diameter of the hose provided.

Likewise the internal diameter of the cou-

plings used for connections to the waste out-

let must be no smaller than the diameter of

the hose provided.

When connecting the drain hose to an under

sink trap spigot, the entire plastic mem-

brane (A) must be removed. Failure to re-

move all the membrane will result in food

particles building up over time eventually

blocking the dishwasher drain hose spigot

20 electrolux

Страница загружается ...

Electrolux ESI65010X Руководство пользователя

Бренд: Electrolux

Модель: ESI65010X

Категория: Посудомоечные машины

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

на других языках

English: Electrolux ESI65010X User manual

Electrolux ESI65010X Руководство пользователя

Electrolux ESI65010X Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов