Pioneer AVIC-F930BT Инструкция по установке

Installation Manual

Руководство по установке

NAVIGATION AV SYSTEM

AV-СИСТЕМА С НАВИГАЦИЕЙ

AVIC-F930BT

English Русский

Precautions

Your new navigation system and this

manual 3

Important safeguards 3

Connecting the system

Precautions before connecting the

system 4

Before installing this product 4

To prevent damage 5

– Notice for the blue/white lead 5

Parts supplied 6

Connecting the system 8

Connecting the power cord (1) 10

Connecting the power cord (2) 12

When connecting to separately sold power

amp 14

When connecting a rear view camera 16

When connecting the external video

component 17

– Using an AV input (AV1) 17

– Using an AV input (AV2) 18

When connecting the rear display 18

– When using a rear display connected to

rear video output 18

When connecting the external unit featuring

video source 19

Installation

Precautions before installation 20

To avoid electromagnetic interference 20

Before installing 20

Installing the navigation system 21

– Installation notes 21

– Parts supplied 22

– Before installing this navigation

unit 23

– Installation with the holder and side

bracket 23

– Installation using the screw holes on

the side of the navigation unit 24

Installing the GPS aerial 25

– Installation notes 25

– Parts supplied 25

– When installing the aerial inside the

vehicle (on the dashboard or rear

shelf) 26

Installing the microphone 27

– Parts supplied 27

– Mounting on the sun visor 27

– Installation on the steering column 28

– Adjusting the microphone angle 28

Contents

Engb

2

Your new navigation

system and this manual

! The navigation features of this product

(and the rear view camera option if pur-

chased) are intended solely to aid you in

the operation of your vehicle. It is not a sub-

stitute for your attentiveness, judgement

and care when driving.

! Never use this navigation system to route

to hospitals, police stations, or similar facil-

ities in an emergency. Please call the ap-

propriate emergency number.

! Do not operate this navigation system (or

the rear view camera option if purchased) if

doing so will divert your attention in any

way from the safe operation of your vehicle.

Always observe safe driving rules and fol-

low all existing traffic regulations. If you ex-

perience difficulty in operating the system

or reading the display, park your vehicle in

a safe location and apply the handbrake be-

fore making the necessary adjustments.

! This manual explains how to install this na-

vigation system in your vehicle. Operation

of this navigation system is explained in

the separate manuals for the navigation

system.

! Do not install this product where it may (i)

obstruct the driver’s vision, (ii) impair the

performance of any of the vehicle’s operat-

ing systems of safety features, including

airbags, hazard lamp buttons, or (iii) impair

the driver’s ability to safely operate the vehi-

cle. In some cases, it may not be possible

to install this product because of the vehi-

cle type or the shape of the vehicle inter-

ior.

Important safeguards

WARNING

Pioneer does not recommend that you install

your navigation system yourself. We recom-

mend that only authorised Pioneer service

personnel, who have special training and ex-

perience in mobile electronics, set up and in-

stall this product. NEVER SERVICE THIS

PRODUCT YOURSELF. Installing or servi-

cing this product and its connecting cables

may expose you to the risk of electric shock

or other hazards, and can cause damage to

the navigation system that is not covered by

warranty.

! Read this manual fully and carefully before

installing your navigation system.

! Keep this manual handy for future refer-

ence.

! Pay close attention to all warnings in this

manual and follow the instructions care-

fully.

! This navigation system may in certain cir-

cumstances display inaccurate position of

your vehicle, the distance of objects shown

on the screen, and compass directions. In

addition, the system has certain limita-

tions, including the inability to identify one-

way streets, temporary traffic restrictions

and potentially unsafe driving areas. Please

exercise your own judgement in the light of

actual driving conditions.

! As with any accessor y in your vehicle’s in-

terior, the navigation system should not di-

vert your attention from the safe operation

of your vehicle. If you experience difficulty

in operating the system or reading the dis-

play, please make adjustments while safely

parked.

! Please remember to wear your seat belt at

all times while operating your vehicle. If

you are in an accident, your injuries can be

considerably more severe if your seat belt

is not properly fastened.

! Certain country and government laws may

prohibit or restrict the placement and use

of this system in your vehicle. Please com-

ply with all applicable laws and regulations

regarding the use, installation and opera-

tion of your navigation system.

Engb

3

English

Section

01

Precautions

Precautions before

connecting the system

CAUTION

! If you decide to perform the installation

yourself, and have special training and ex-

perience in the mobile electronics instal-

lations, please carefully follow all of the

steps in the installation manual.

! Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wir-

ing to remain exposed.

! Do not directly connect the yellow lead of

this product to the vehicle battery. If the

lead is directly connected to the battery,

engine vibration may eventually cause

the insulation to fail at the point where

the wire passes from the passenger com-

partment into the engine compartment. If

the yellow lead’s insulation tears as a re-

sult of contact with metal parts, short-cir-

cuiting can occur, resulting in

considerable danger.

! It is extremely dangerous to allow cables

to become wound around the steering col-

umn or gearstick. Be sure to install this

product, its cables, and wiring away in

such so that they will not obstruct or hin-

der driving.

! Make sure that the cables and wires will

not interfere with or become caught in

any of the vehicle’s moving parts, espe-

cially the steering wheel, gearstick, hand-

brake, sliding seat tracks, doors, or any of

the vehicle’s controls.

! Do not route wires where they will be ex-

posed to high temperatures. If the insula-

tion heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

! Do not cut the GPS aerial cable to shorten

it or use an extension to make it longer.

Altering the aerial cable could result in a

short circuit or malfunction.

! Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse resis-

tor or filter, etc.) may fail to work properly.

! Never feed power to other electronic pro-

ducts by cutting the insulation of the

power supply lead of the navigation sys-

tem and tapping into the lead. The current

capacity of the lead will be exceeded,

causing overheating.

Before installing this product

! Use this unit with a 12-volt battery and ne-

gative earthing only. Failure to do so may

result in a fire or malfunction.

! To avoid shorts in the electrical system, be

sure to disconnect the (–) battery cable be-

fore installation.

Engb

4

Section

02

Connecting the system

To prevent damage

WARNING

! Use speakers over 50 W (output value)

and between 4 W to 8 W (impedance value).

Do not use 1 W to 3 W speakers for this

unit.

! The black lead is earth. Please earth this

lead separately from the earth of high-cur-

rent products such as power amps. Do not

earth more than one product together

with the earth from another product. For

example, you must separately earth any

amp unit away from the earth of this navi-

gation system. Connecting earths to-

gether can cause a fire and/or damage the

products if their earths became detached.

! When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

! When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

! This product cannot be installed in a vehi-

cle without ACC (accessory) position on

the ignition switch.

A

C

O

N

S

T

A

R

T

O

F

O

N

S

T

A

R

T

O

F

ACC position No ACC position

! To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe-

cially important to insulate all unused

speaker leads, which if left uncovered may

cause a short circuit.

! Attach the connectors of the same colour

to the corresponding coloured port, i.e.,

blue connector to the blue port, black to

black, etc.

! Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

! Since a unique BPTL circuit is employed,

do not directly earth the * side of the

speaker lead or connect the * side of an-

other side of the speaker lead together. Be

sure to connect the * side of the speaker

lead to the * side of the speaker lead on

this navigation system.

! If the RCA pin jack on this product will not

be used, do not remove the caps attached

to the end of the connector.

Notice for the blue/white lead

! When the ignition switch is turned on (ACC

ON), a control signal is output through the

blue/white lead. Connect to an external

power amp’s system remote control term-

inal, the auto-aerial relay control terminal,

or the aerial booster power control terminal

(max. 300 mA 12 V DC). The control signal

is output through the blue/white lead, even

if the audio source is switched off.

! Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive

current drain and malfunction.

! Be sure not to use this lead as the power

supply lead for the auto-aerial or aerial

booster. Such connection could cause ex-

cessive current drain and malfunction.

Engb

5

English

Section

02

Connecting the system

Parts supplied

The navigation unit Power cord

USB and mini-jack

connector

RCA connector

GPS aerial Microphone

Engb

6

Section

02

Connecting the system

Engb

7

English

Section

02

Connecting the system

USB and mini-jack

connector

(

*

2)

— When connecting your iPod, both connections are necessary.

— You must set “AV1 Input” in “AV System Settings” to “iPod” when

connecting the iPod. (For details, refer to Operation Manual.)

(

*

2)

Aerial

jack

Vehicle

aerial

2 m

The navigation unit

IP-BUS connector

(

*

1)

Connect either the USB Interface

Cable for iPod or an appropriate

USB storage device.

(

*

1)

Wired remote input

Please refer to the instruction

manual for the Wired Remote

Control Adapters (sold separately).

Engb

8

Section

02

Connecting the system

Dock

Connector

port

WARNING

· To avoid the risk of accident and the potential violation of applicable laws, this

product should never be used while the vehicle is being driven except for

navigation purposes. And, also rear displays should not be in a location where it

is a visible distraction to the driver.

· In some countries, the viewing of images on a display inside a vehicle even by

persons other than the driver may be illegal. Where such regulations apply they

must be obeyed and this product’s video source should not be used.

USB Interface Cable for iPod

(CD-IU51V) (sold separately)

iPod with

Dock Connector (*3)

(*3)

For details concerning

operations and compatibility,

refer to Operation Manual.

4 m

Microphone

3.55 m

GPS aerial

Engb

9

English

Section

02

Connecting the system

Connecting the power cord (1)

ISO connector

*1

*3

*2

*4

Speaker leads

White: Front left 

White/black: Front left 

Grey: Front right 

Grey/black: Front right 

Green: Rear left  or Subwoofer  (*5)

Green/black: Rear left  or Subwoofer  (*5)

Violet: Rear right  or Subwoofer  (*5)

Violet/black: Rear right  or Subwoofer  (*5)

Depending on the types of vehicles, the

function of *2 and *4 may be different. In this

case, be sure to connect *1 to *4 and *3 to *2

as shown in the figure.

Connect leads of the

same colour to each other.

Yellow (*2)

Back-up

(or accessory)

Red (*4)

Accessory

(or back-up)

Yellow (*1)

To terminal supplied with

power regardless of ignition

switch position.

Red (*3)

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (earth)

To vehicle (metal) body.

Note

Notes

· When a subwoofer (*5) is connected to this

navigation system instead of a rear speaker, change

the rear output setting in the initial setting. (Refer to

Operation Manual.) The subwoofer output of this

navigation system is monaural.

· When using a subwoofer of 70 W (2 Ω), be sure to

connect with violet and violet/black leads of this

navigation system. Do not connect anything with

green and green/black leads.

In some vehicles, the ISO connector may be divided

into two. In this case, be sure to connect to both

connectors.

Note

Engb

10

Section

02

Connecting the system

The navigation unit

Blue/white (*6)

Blue/white (*7)

To auto-aerial relay control

terminal (max. 300 mA 12 V DC).

The pin position of the ISO connector will differ

depending on the types of vehicles. Connect *6

and *7 when Pin 5 is an aerial control type. In

other types of vehicles, never connect *6 and *7.

Yellow/black

If you use an equipment with mute function, connect that

equipment to the Audio Mute lead. If not, keep this lead free of any

connections.

Power cord

Audio source will be set to mute or attenuate, while the following

sounds will not be muted or attenuated. For details, refer to

Operation Manual.

— Voice guidance of the navigation

— Incoming ringtone and incoming voice of the mobile phone

that is connected to this navigation system via Bluetooth

wireless technology

15 cm

Note

RCA connector

Fuse (10 A)

Engb

11

English

Section

02

Connecting the system

Connecting the power cord (2)

Pink (CAR SPEED SIGNAL INPUT)

The navigation system is connected here to detect the distance the vehicle travels. Always connect

the vehicle’s speed detection circuit. Failure to make this connection will increase errors in the

vehicle's location display.

LIGHT GREEN LEAD AT POWER CONNECTOR IS

DESIGNED TO DETECT PARKED STATUS AND MUST

BE CONNECTED TO THE POWER SUPPLY SIDE OF THE

HANDBRAKE SWITCH. IMPROPER CONNECTION OR

USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW

AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.

Light green (PARKING BRAKE)

Used to detect the ON/OFF status of the handbrake. This lead must be connected to the power supply side

of the handbrake switch.

If this connection is made incorrectly or omitted, certain functions of your navigation system will be

unusable.

Power supply side

Earth side

Handbrake switch

Connection method

Clamp the lead of the power supply

side of the handbrake switch.

Clamp firmly with needle-nosed

pliers.

The position of the speed detection circuit and the position of the handbrake switch vary

depending on the vehicle model. For details, consult your authorised Pioneer dealer or an

installation professional.

Note

WARNING

CAUTION

It is strongly suggested that the speed pulse wire be connected for accuracy of navigation

and better performance.

IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE OR INJURY INCLUDING

ELECTRICAL SHOCK, AND INTERFERENCE WITH THE OPERATION OF THE VEHICLE´S ANTILOCK

BRAKING SYSTEM, AUTOMATIC GEARBOX AND SPEEDOMETER INDICATION.

WARNING

Engb

12

Section

02

Connecting the system

Power cord

Violet/white (REVERSE GEAR SIGNAL INPUT)

This is connected so that the navigation system can detect

whether the vehicle is moving forwards or backwards.

Connect the violet/white lead to the lead whose voltage

changes when the reverse gear is engaged. Unless

connected, the sensor may not detect your vehicle

travelling forward/backward properly, and thus the position

of your vehicle detected by the sensor may be misaligned

from the actual position.

When you use a rear view camera, please make

sure to connect this lead. Otherwise you cannot

switch to the rear view camera picture.

The navigation unit

Note

Engb

13

English

Section

02

Connecting the system

When connecting to separately sold power amp

The navigation unit

RCA connector

Subwoofer outputs

(SWL, SWR)

Power cord

To system control terminal of the power amp

(max. 300 mA 12 V DC).

Blue/white

Rear outputs

(REAR OUTPUT)

Front outputs

(FRONT OUTPUT)

15 cm

Engb

14

Section

02

Connecting the system

























Left Right

System remote control

You can change the RCA output of the subwoofer depending on your subwoofer

system. (Refer to Operation Manual.)

Note

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

Front speaker Front speaker

Rear speaker Rear speaker

Subwoofer Subwoofer

RCA

cables

(sold separately)

Engb

15

English

Section

02

Connecting the system

When connecting a rear

view camera

When this product is used with a rear view

camera, it is possible to automatically switch

from the video to rear view image when the

gearstick is moved to REVERSE (R). Rear

View mode also allows you to check what is

behind you while driving.

WARNING

USE INPUT ONLY FOR REVERSE OR MIRROR

IMAGE REAR VIEW CAMERA. OTHER USE MAY

RESULT IN INJURY OR DAMAGE.

CAUTION

! The screen image may appear reversed.

! The rear view camera is used as an aid to

keep an eye on trailers, or backing into a tight

parking spot. Do not use this function for en-

tertainment purposes.

! Objects in rear view may appear closer or

more distant than in reality.

! Please note that the image area shown by the

rear view camera may differ slightly when full-

screen images are displayed when backing

and when checking the rear of the vehicle

while moving forward.

The navigation unit

20 cm

(e.g. ND-BC4)

(sold separately)

Rear view camera

To video output

RCA cable

Brown

(REAR VIEW CAMERA IN)

RCA connector

Power cord

(REVERSE GEAR SIGNAL INPUT)

Violet/white

For more details about the wiring, refer to Connecting

the power cord (2) on page 12.

Notes

! This mode is available when the rear view

camera setting is set to “On”. (For details,

refer to Operation Manual.)

! Connect the navigation system to the rear

view camera only. Do not connect to any

other equipment.

Engb

16

Section

02

Connecting the system

When connecting the

external video component

Using an AV input (AV1)

The navigation unit

RCA cables

(sold separately)

Yellow

Red, white

External video

component

(sold separately)

To video output

To audio outputs

Mini-jack AV cable

(CD-RM10)

(sold separately)

USB and

mini-jack connector

2 m

! You must set “AV1 Input” in “AV System

Settings” to “Video” when connecting the

external video component. (For details,

refer to Operation Manual.)

CAUTION

Be sure to use a mini-jack AV cable (CD-RM10)

(sold separately) for wiring. If you use other

cables, the wiring position might differ resulting

in disturbed images and sounds.

OK

G

V

R

L

G

R

V

L

L : Left audio (White)

R : Right audio (Red)

V : Video (Yellow)

G : Earth

Engb

17

English

Section

02

Connecting the system

Using an AV input (AV2)

To audio outputs

Yellow

(VIDEO INPUT)

RCA connector

Red, white

(AUDIO INPUT)

RCA cables

(sold separately)

To video output

The navigation unit

External video

component

(sold separately)

20 cm

! You must set “AV2 Input” in “AV System

Settings” to “Video” when connecting the

external video component. (For details,

refer to Operation Manual.)

When connecting the rear

display

The navigation unit

Rear display with

RCA input jacks

Yellow

(VOUT)

RCA cable

(sold separately)

To video input

When using a rear display

connected to rear video output

WARNING

NEVER install the rear display in a location

that enables the driver to watch the video

source while driving.

This navigation system’s rear video output is for

connection of a display to enable passengers in

the rear seats to watch the video source.

Engb

18

Section

02

Connecting the system

When connecting the exter nal

unit featuring video source

The navigation unit

Blue

Pioneer external unit

(sold separately)

Yellow

(VIDEO INPUT)

To video output

Black

RCA connector

IP-BUS cable

(sold separately)

RCA cable

(sold separately)

20 cm

T

o IP-BUS

output

! You must set “AV2 Input” in “AV System

Settings” to “EXT” when connecting the ex-

ternal unit. (For details, refer to Operation

Manual.)

Engb

19

English

Section

02

Connecting the system

Precautions before

installation

CAUTION

! Never install this product in places where,

or in a manner that:

— Could injure the driver or passengers if

the vehicle stops suddenly.

— May interfere with the driver’s opera-

tion of the vehicle, such as on the floor

in front of the driver’s seat, or close to

the steering wheel or gearstick.

! Make sure there is nothing behind the

dashboard or panelling when drilling

holes in them. Be careful not to damage

fuel lines, brake lines, electronic compo-

nents, communication wires or power

cables.

! When using screws, do not allow them to

come into contact with any electrical lead.

Vibration may damage wires or insulation,

leading to a short circuit or other damage

to the vehicle.

! To ensure proper installation, be sure to

use the supplied parts in the manner spe-

cified. If any parts are not supplied with

this product, use compatible parts in the

manner specified af ter you have the parts’

compatibility checked by your dealer. If

parts other than supplied or compatible

ones are used, they may damage internal

parts of this product or they may work

loose and the product may become de-

tached.

! It is extremely dangerous to allow cables

to become wound around the steering col-

umn or gearstick. Be sure to install this

product, its cables, and wiring away in

such so that they will not obstruct or hin-

der driving.

! Make sure that leads cannot get caught in

a door or the sliding mechanism of a seat,

resulting in a short circuit.

! Please confirm the proper function of

your vehicle’s other equipment after in-

stallation of the navigation system.

! Do not install this navigation system

where it may (i) obstruct the driver’s vi-

sion, (ii) impair the performance of any of

the vehicle’s operating systems or safety

features, including airbags, hazard lamp

buttons or (iii) impair the driver’s ability

to safely operate the vehicle.

! Install the navigation system between the

driver’s seat and front passenger seat so

that it will not be hit by the driver or pas-

senger if the vehicle stops quickly.

! Never install the navigation system in

front of or next to the place in the dash-

board, door, or pillar from which one of

your vehicle’s airbags would deploy.

Please refer to your vehicle’s owner’s

manual for reference to the deployment

area of the frontal airbags.

To avoid electromagnetic

interference

In order to prevent interference, set the follow-

ing items as far as possible from this naviga-

tion system, other cables or leads:

! FM, MW/LW aerial and its lead

! GPS aerial and its lead

In addition, you should lay or route each aerial

lead as far as possible from other aerial leads.

Do not bind, lay or route them together, or

cross them. Electromagnetic noise will in-

crease the potential for errors in the vehicle's

location display.

Before installing

! Consult with your nearest dealer if installa-

tion requires drilling holes or other modifi-

cations of the vehicle.

! Before making a final installation of this

product, temporarily connect the wiring to

confirm that the connections are correct

and the system works properly.

Engb

20

Section

03

Installation

Страница загружается ...

Pioneer AVIC-F930BT Инструкция по установке

Pioneer AVIC-F930BT Инструкция по установке

на других языках

Похожие модели бренда

Модели других брендов