Pioneer SPH-DA100 Инструкция по применению

SPH-DA100

AppRadio

Installation Manual

Manuel d’installation

Руководство по установке

English Français Italiano Español Deutsch Nederlands

Русский

Contents

2

Engb

01

Precautions

Your new display unit and this manual .........

3

Important safeguards ...................................

3

02

Connecting the system

Precautions before connecting

the system ................................................

4

Before installing this product ...........................

4

To prevent damage ........................................

5

Notice for the blue/white lead .....................

5

Parts supplied ................................................

6

Installing the HDMI holder ............................

6

Connecting the system ..................................

7

Connecting the power cord (1) .....................

8

Connecting the power cord (2) ..................

10

When connecting to separately sold

power amp/subwoofer............................

11

When connecting a rear view camera .......

12

03

Installation

Precautions before installation ..................

13

To avoid electromagnetic interference ......

13

Before installing .........................................

13

Installing this product ................................

14

Installation notes .......................................

14

Parts supplied ............................................

15

Before installing this product .....................

15

Installation with the holder and

side bracket ...............................................

16

Removing the unit ......................................

16

Installation using the screw holes

on the side of this product .........................

17

Installing the GPS aerial .............................

18

Installation notes .......................................

18

Parts supplied ............................................

18

When installing the aerial inside the

vehicle (on the dashboard or rear shelf) ....

19

₋

Installing the microphone ..........................

20

Parts supplied ............................................

20

Mounting on the sun visor .........................

20

Installation on the steering column ...........

21

Adjusting the microphone angle ................

21

₋

01

Precautions

Section

3

Engb

English

Your new display unit and

this manual

Do not operate this product, any applica-

tions, or the rear view camera option (if

purchased) if doing so will divert your atten-

tion in any way from the safe operation of

your vehicle. Always observe safe driving

rules and follow all existing traffic regula-

tions. If you experience difficulty in operat-

ing this product or reading the display, park

your vehicle in a safe location and apply the

handbrake before making the necessary

adjustments.

Do not install this product where it may (i)

obstruct the driver’s vision, (ii) impair the

performance of any of the vehicle’s operat-

ing systems of safety features, including air-

bags, hazard lamp buttons, or (iii) impair

the driver’s ability to safely operate the

vehicle. In some cases, it may not be possi-

ble to install this product because of the

vehicle type or the shape of the vehicle

interior.

This manual explains how to install this

product in your vehicle. Operation of this

product is explained in the separate man-

uals.

•

Important safeguards

WARNING

Pioneer does not recommend that you install

this product yourself. We recommend that

only authorised Pioneer service personnel,

who have special training and experience

in mobile electronics, set up and install this

product. NEVER SERVICE THIS PRODUCT

YOURSELF. Installing or servicing this prod-

uct and its connecting cables may expose

you to the risk of electric shock or other

hazards, and can cause damage to the prod-

uct that is not covered by warranty.

Read this manual fully and carefully before

installing this product.

Keep this manual handy for future refer-

ence.

Pay close attention to all warnings in this

manual and follow the instructions care-

fully.

Traffic restrictions and advisories are always

more important than guidance given by a

third-party navigation/mapping smart-

phone application. Always obey current

traffic restrictions, even if the application

provides contrary advice.

As with any accessory in your vehicle’s inte-

rior, this product should not divert your

attention from the safe operation of your

vehicle. If you experience difficulty in oper-

ating this product or reading the display,

please make adjustments while safely

parked.

Please remember to wear your seat belt at

all times while operating your vehicle. If you

are in an accident, your injuries can be con-

siderably more severe if your seat belt is

not properly fastened.

Certain country and government laws may

prohibit or restrict the placement and use

of this product in your vehicle. Please com-

ply with all applicable laws and regulations

regarding the use, installation and opera-

tion of this product.

•

Connecting the system

02

Section

4

Engb

Precautions before

connecting the system

CAUTION

If you decide to perform the installation

yourself, and have special training and

experience in the mobile electronics

installations, please carefully follow all

of the steps in the installation manual.

Secure all wiring with cable clamps or

electrical tape. Do not allow any bare

wiring to remain exposed.

Do not directly connect the yellow lead

of this product to the vehicle battery. If

the lead is directly connected to the

battery, engine vibration may eventu-

ally cause the insulation to fail at the

point where the wire passes from the

passenger compartment into the

engine compartment. If the yellow

lead’s insulation tears as a result of

contact with metal parts, short-

circuiting can occur, resulting in con-

siderable danger.

It is extremely dangerous to allow

cables to become wound around the

steering column or gearstick. Be sure

to install this product, its cables, and

wiring away in such so that they will

not obstruct or hinder driving.

Make sure that the cables and wires

will not interfere with or become

caught in any of the vehicle’s moving

parts, especially the steering wheel,

gearstick, handbrake, sliding seat

tracks, doors, or any of the vehicle’s

controls.

Do not route wires where they will be

exposed to high temperatures. If the

insulation heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

•

Do not cut the GPS aerial cable to

shorten it or use an extension to make

it longer. Altering the aerial cable could

result in a short circuit or malfunction.

Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse

resistor or ﬁ lter, etc.) may fail to work

properly.

Never feed power to other electronic

products by cutting the insulation of

the power supply lead of this product

and tapping into the lead. The current

capacity of the lead will be exceeded,

causing overheating.

Before installing this product

Use this unit with a 12-volt battery and neg-

ative earthing only. Failure to do so may

result in a fire or malfunction.

To avoid shorts in the electrical system, be

sure to disconnect the (−) battery cable

before installation.

•

02

Connecting the system

Section

5

Engb

English

To prevent damage

WARNING

Use speakers over 50 W (output value)

and between 4

Ω to 8 Ω (impedance

value). Do not use 1

Ω to 3 Ω speakers

for this unit.

The black lead is earth. Please earth

this lead separately from the earth of

high-current products such as power

amps. Do not earth more than one

product together with the earth from

another product. For example, you

must separately earth any amp unit

away from the earth of this product.

Connecting earths together can cause

a ﬁ re and/or damage the products if

their earths became detached.

When replacing the fuse, be sure to

only use a fuse of the rating prescribed

on this product.

When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

This product cannot be installed in a vehi-

cle without ACC (accessory) position on

the ignition switch.

A

C

O

N

S

T

A

R

T

O

F

O

N

S

T

A

R

T

O

F

ACC position No ACC position

To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe-

cially important to insulate all unused

speaker leads, which if left uncovered may

cause a short circuit.

Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

•

Since a unique BPTL circuit is employed, do

not directly earth the

side of the speaker

lead or connect the

side of another side

of the speaker lead together. Be sure to

connect the

side of the speaker lead to

the side of the speaker lead on this prod-

uct.

If the RCA pin jack on this product will not

be used, do not remove the caps attached

to the end of the connector.

Notice for the blue/white lead

When the ignition switch is turned on (ACC

ON), a control signal is output through the

blue/white lead. Connect to an external

power amp’s system remote control termi-

nal (max. 300 mA 12 V DC). The control sig-

nal is output through the blue/white lead,

even if the AV source is switched off.

Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive cur-

rent drain and malfunction.

Be sure not to use this lead as the power

supply lead for the auto-aerial or aerial

booster. Such connection could cause exces-

sive current drain and malfunction.

•

Connecting the system

02

Section

6

Engb

Parts supplied

This product Power cord

GPS aerial iPhone cable

Microphone HDMI holder

Installing the HDMI holder

1 Insert the lower tab of the HDMI

holder into the groove of this product.

Tab

Groove

2 Insert the two upper tabs into the

this product by pushing the HDMI

holder.

Tabs

❐ Use the HDMI holder when you connect

this product with the separately sold

App Connectivity Kit (CD-AH200C).

❐ Never grip the holder tightly or use force

when removing or attaching.

02

Connecting the system

Section

7

Engb

English

Connecting the system

Wired remote input

Please refer to the instruction

manual for the Hard-wired remote

control adapter (sold separately).

4 m

2.25 m

3.55 m

Microphone

iPhone cable

GPS aerial

HDMI holder

Android™ device (*1)

iPhone or iPod with Dock Connector (*1)

(*1)

For details concerning operations and compatibility, refer to the Operation Manual.

(*2)

For details about how to connect the separately sold

App Connectivity Kit (CD-AH200C), refer to the App Connectivity Kit manual.

Vehicle aerial

This product

USB - micro USB cable (*2)

(sold separately)

Power supply box (*2)

(sold separately)

Type A - A

Type A - D

HDMI cables (*2)

(sold separately)

WARNING

To avoid the risk of accident and the potential violation of applicable laws, this product should

never be used while the vehicle is being driven except for navigation purposes.

In some countries, the viewing of images on a display inside a vehicle even by persons other than

the driver may be illegal. Where such regulations apply they must be obeyed and this product’s

app-based content should not be used.

•

Connecting the system

02

Section

8

Engb

Connecting the power cord (1)

Note

Depending on the vehicle type,

the function of *2 and *4 may be

different. In this case, be sure to

connect *1 to *4 and *3 to *2 as

shown in the figure.

Notes

When a subwoofer (*5) is connected to this

product instead of a rear speaker, change

the rear output setting in the initial setting.

(Refer to the Operation Manual.) The sub-

woofer output of this product is monaural.

When using a subwoofer of 70 W (2 Ω), be

sure to connect with the violet and violet/

black leads of this product. Do not connect

anything with the green and green/black

leads.

•

Connect leads of the same colour to

each other.

Yellow (*2)

Back-up

(or accessory)

Yellow (*1)

To terminal supplied with power

regardless of ignition switch position.

Red (*4)

Accessory

(or back-up)

Red (*3)

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (earth)

To vehicle (metal) body.

ISO connector

Speaker leads

White: Front left 

White/black: Front left 

Grey: Front right 

Grey/black: Front right 

Green: Rear left  or Subwoofer  (*5)

Green/black: Rear left  or Subwoofer  (*5)

Violet: Rear right  or Subwoofer  (*5)

Violet/black: Rear right  or Subwoofer  (*5)

Note

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to

connect to both connectors.

*2 *1

*4 *3

02

Connecting the system

Section

9

Engb

English

10

This product

Fuse (10 A)

Power cord

Blue/white (*6)

Blue/white (*7)

To auto-aerial relay control terminal

(max. 300 mA 12 V DC).

The pin position of the ISO connector will differ

depending on the vehicle type. Connect *6 and

*7 when Pin 5 is an aerial control type. In other

types of vehicles, never connect *6 and *7.

Connecting the system

02

Section

10

Engb

Connecting the power cord (2)

Note

The position of the handbrake switch

varies depending on the vehicle

model. For details, consult your

authorised Pioneer dealer or an

installation professional.

Violet/white (REVERSE GEAR SIGNAL INPUT)

This is connected so that the this product can detect

whether the vehicle is moving forwards or backwards.

Connect the violet/white lead to the lead whose

voltage changes when the reverse gear is engaged.

Unless connected, the sensor may not detect your

vehicle travelling forward/backward properly, and thus

the position of your vehicle detected by the sensor may

be misaligned from the actual position.

WARNING

LIGHT GREEN LEAD AT POWER CONNECTOR IS

DESIGNED TO DETECT PARKED STATUS AND

MUST BE CONNECTED TO THE POWER SUPPLY

SIDE OF THE HANDBRAKE SWITCH. IMPROPER

CONNECTION OR USE OF THIS LEAD MAY

VIOLATE APPLICABLE LAW AND MAY RESULT IN

SERIOUS INJURY OR DAMAGE.

Note

When you use a rear view camera, please

make sure to connect this lead. Otherwise

you cannot switch to the rear view camera

picture.

This product

Power cord

Power supply side

Earth side

Handbrake switch

Connection method

Clamp the lead of the power supply

side of the handbrake switch.

Clamp firmly with needle-nosed

pliers.

Light green (PARKING BRAKE)

Used to detect the ON/OFF status of the

handbrake. This lead must be connected to the

power supply side of the handbrake switch.

If this connection is made incorrectly or

omitted, certain functions of this product

will be unusable.

02

Connecting the system

Section

11

Engb

English

When connecting to separately sold power amp/subwoofer

















This product

Front outputs

(FL, FR)

Subwoofer/rear outputs

(SW/RL, SW/RR)

Power cord

RCA cables

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

System remote control

Left Right

Front speaker Front speaker

Subwoofer or

Rear speaker

Subwoofer or

Rear speaker

Blue/white

To system control terminal

of the power amp

(max. 300 mA 12 V DC).

Note

You can change the RCA output of the subwoofer depending

on your subwoofer system. (Refer to the Operation Manual.)

Connecting the system

02

Section

12

Engb

When connecting a rear

view camera

When this product is used with a rear view

camera, it is possible to automatically

switch from the video to rear view image

when the gearstick is moved to REVERSE

(R). Rear Camera mode also allows you to

check what is behind you while driving.

WARNING

USE INPUT ONLY FOR REVERSE OR MIRROR

IMAGE REAR VIEW CAMERA. OTHER USE

MAY RESULT IN INJURY OR DAMAGE.

CAUTION

The screen image may appear reversed.

The rear view camera is used as an aid to

keep an eye on trailers, or backing into a

tight parking spot. Do not use this function

for entertainment purposes.

Objects in rear view may appear closer or

more distant than in reality.

Please note that the image area shown by

the rear view camera may differ slightly

when full-screen images are displayed when

backing and when checking the rear of the

vehicle while moving forward.

•

This product

Rear view camera

(e.g. ND-BC5)

(sold separately)

For more details about the wiring, refer to

Connecting the power cord (2) on page 10.

Notes

To display the rear view camera image, set

the rear view camera to on.

Connect this product to the rear view cam-

era only. Do not connect to any other equip-

ment.

•

Power cord

Violet/white

(REVERSE GEAR

SIGNAL INPUT)

03

Installation

Section

13

Engb

English

Precautions before

installation

CAUTION

Never install this product in places

where, or in a manner that:

– Could injure the driver or passengers

if the vehicle stops suddenly.

– May interfere with the driver’s opera-

tion of the vehicle, such as on the

floor in front of the driver’s seat, or

close to the steering wheel or gear-

stick.

Make sure there is nothing behind the

dashboard or panelling when drilling

holes in them. Be careful not to dam-

age fuel lines, brake lines, electronic

components, communication wires or

power cables.

When using screws, do not allow them

to come into contact with any electrical

lead. Vibration may damage wires or

insulation, leading to a short circuit or

other damage to the vehicle.

To ensure proper installation, be sure

to use the supplied parts in the manner

speciﬁ ed. If any parts are not supplied

with this product, use compatible parts

in the manner speciﬁ ed after you have

the parts’ compatibility checked by

your dealer. If parts other than supplied

or compatible ones are used, they may

damage internal parts of this product

or they may work loose and the prod-

uct may become detached.

It is extremely dangerous to allow

cables to become wound around the

steering column or gearstick. Be sure

to install this product, its cables, and

wiring away in such so that they will

not obstruct or hinder driving.

Make sure that leads cannot get caught

in a door or the sliding mechanism of a

seat, resulting in a short circuit.

•

Please conﬁ rm the proper function of

your vehicle’s other equipment after

installation of this product.

Do not install this product where it may

(i) obstruct the driver’s vision, (ii)

impair the performance of any of the

vehicle’s operating systems or safety

features, including airbags, hazard

lamp buttons or (iii) impair the driver’s

ability to safely operate the vehicle.

Install this product between the driv-

er’s seat and front passenger seat so

that it will not be hit by the driver or

passenger if the vehicle stops quickly.

Never install this product in front of or

next to the place in the dashboard,

door, or pillar from which one of your

vehicle’s airbags would deploy. Please

refer to your vehicle’s owner’s manual

for reference to the deployment area of

the frontal airbags.

To avoid electromagnetic

interference

In order to prevent interference, set the fol-

lowing items as far as possible from this

product, other cables or leads:

FM, MW/LW aerial and its lead

GPS aerial and its lead

In addition, you should lay or route each

aerial lead as far as possible from other aer-

ial leads. Do not bind, lay or route them

together, or cross them. Electromagnetic

noise will increase the potential for errors in

the vehicle’s location display.

Before installing

Consult with your nearest dealer if installa-

tion requires drilling holes or other modifi-

cations of the vehicle.

Before making a final installation of this

product, temporarily connect the wiring to

confirm that the connections are correct

and the system works properly.

•

Installation

03

Section

14

Engb

Installing this product

Installation notes

Do not install this product in places subject

to high temperatures or humidity, such as:

– Places close to a heater, vent or air con-

ditioner.

– Places exposed to direct sunlight, such

as on top of the dashboard.

– Places that may be exposed to rain,

such as close to the door or on the

vehicle’s floor.

Install this product in an area strong enough

to bear its weight. Choose a position where

this product can be firmly installed, and

install it securely. If this product is not

securely installed, the current location of

the vehicle cannot be displayed correctly.

Install this product horizontally on a surface

within 0 to 60 degrees tolerance. Improper

installation of the unit with the surface

tilted more than these tolerances increases

the potential for errors in the vehicle’s loca-

tion display, and might otherwise cause

reduced display performance.

60°

•

When installing, to ensure proper heat dis-

persal when using this unit, make sure you

leave ample space behind the rear panel

and wrap any loose cables so they are not

blocking the vents.

Leave ample

space

5 cm

•

03

Installation

Section

15

Engb

English

Parts supplied

Parts marked (*) are pre-installed.

The display unit Holder*

Flush surface screw

(5 mm × 9 mm)

(6 pcs.)

Truss head crew

(5 mm × 8 mm)

(6 pcs.)

Trim ring* Extraction key

(2 pcs.)

Before installing this product

1 Remove the trim ring.

Extend top and bottom of the trim ring

outwards to remove the trim ring.

Trim ring

2 Insert the supplied extraction keys

into both sides of the unit until they

click into place.

3 Pull the unit out of the holder.

Extraction key

Installation

03

Section

16

Engb

Installation with the holder and

side bracket

1 Install the holder into the dashboard.

After inserting the holder into the dash-

board, select and bend the tabs appropriate

to the thickness of the dashboard material.

(Install this product as firmly as possible

using the top and bottom tabs. To secure

this product, bend the tabs 90 degrees.)

Dashboard

Holder

2 Install this product into the holder.

Dashboard

3 Attach the trim ring.

Trim ring

Removing the unit

1 Remove the trim ring.

Releasing the front panel allows easier

access to the trim ring.

Trim ring

2 Insert the supplied extraction keys

into both sides of the unit until they click

into place.

03

Installation

Section

17

Engb

English

3 Pull the unit out of the dashboard.

Extraction key

Installation using the screw holes

on the side of this product

1 Fasten the unit to the factory radio-

mounting bracket.

Position this product so that its screw holes

are aligned with the screw holes of the

bracket, and tighten the screws at three or

four locations on each side. Use either the

truss head screws (5 mm × 8 mm) or flush

surface screws (5 mm × 9 mm), depending

on the shape of the bracket’s screw holes.

If the tab interferes with installation,

you may bend it down out of the way.

Factory radio-mounting bracket

Truss head screw or

flush surface screw

Be sure to use the

screws supplied

with this product.

Dashboard or console

Installation

03

Section

18

Engb

Installing the GPS aerial

CAUTION

Do not cut the GPS aerial lead to

shorten it or use an extension to make

it longer. Altering the aerial cable could

result in a short circuit or malfunction

and permanent damage to this product.

Installation notes

The aerial should be installed on a level sur-

face where radio waves will be blocked as

little as possible. Radio waves cannot be

received by the aerial if reception from the

satellite is blocked.

Dashboard Rear shelf

When installing the GPS aerial inside the

vehicle, be sure to use the metal sheet pro-

vided with your system. If this is not used,

the reception sensitivity will be poor.

Do not cut the accessory metal sheet. This

would reduce the sensitivity of the GPS aer-

ial.

Take care not to pull the aerial lead when

removing the GPS aerial. The magnet

attached to the aerial is very powerful, and

the lead may become detached.

Do not paint the GPS aerial, as this may

affect its performance.

•

Parts supplied

GPS aerial Metal sheet

03

Installation

Section

19

Engb

English

When installing the aerial inside the vehicle

(on the dashboard or rear shelf)

WARNING

Do not install the GPS aerial over any sensors or vents on the dashboard of the vehicle, as do-

ing so may interfere with the proper functioning of such sensors or vents and may compro-

mise the ability of the double-sided tape under the GPS aerial to properly and securely affix

to the dashboard.

Affix the double-sided tape on the surface as level as possible where the GPS aerial faces the

window. Place the GPS aerial on the double-sided tape.

GPS aerial

Metal sheet

Peel off the protective sheet

on the rear.

Make sure the surface is free of

moisture, dust, grime, oil, etc.,

before affixing the metal sheet.

Clamps

Use separately sold clamps

to secure the lead where necessary

inside the vehicle.

Note

The metal sheet contains

a strong adhesive which

may leave a mark on the

surface if it is removed.

Notes

When attaching the metal sheet, do not cut

it into small pieces.

Some vehicles use window glass that does

not allow signals from GPS satellites to pass

through. On such models, install the GPS

aerial on the outside of the vehicle.

•

Installation

03

Section

20

Engb

Installing the microphone

Install the microphone in a place where its

direction and distance from the driver make

it easiest to pick up the driver’s voice.

Be sure to turn off (ACC OFF) the product

before connecting the microphone.

Parts supplied

Microphone Microphone clip

Double-sided tape

Mounting on the sun visor

1 Install the microphone in the micro-

phone clip.

Microphone clip Microphone

•

2 Attach the microphone clip to the sun

visor.

Microphone clip

Clamps

Use separately sold clamps to secure the

lead where necessary inside the vehicle.

Install the microphone on the sun visor

when it is in the up position. It cannot rec-

ognise the driver’s voice if the sun visor is in

the down position.

Страница загружается ...

Pioneer SPH-DA100 Инструкция по применению

Pioneer SPH-DA100 Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов