DeWalt DCMPH566 Руководство пользователя

Бренд: DeWalt

Модель: DCMPH566

Категория: Триммеры для живой изгороди

Тип: Руководство пользователя

DCMPH566

Final Page size: A5 (148mm x 210mm)

ENGLISH

English (original instructions) 4

Pусский (перевод соригинала инструкции) 16

Англійська (оригінальні інструкції) 32

DEWALT

Fig. A

Fig. B Fig. C

Fig. D

510

12 14

815

XXXX XX XX

Fig. F

Fig. E

Fig. H

Fig. I

Fig. G

Fig. J

Fig. LFig. K

Fig. M Fig. N

ENGLISH

WARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Denotes risk of electricshock.

Denotes risk offire.

EC-Declaration of Conformity

Machinery Directive

18V Pole Hedge Trimmer

DCMPH566

DEWALT

declares that these products described under

Technical Data are in compliance with:

The vibration and/or noise emission level given in this

information sheet has been measured in accordance with

a standardised test given in EN62841 and may be used to

compare one tool with another. It may be used for a preliminary

assessment ofexposure.

WARNING: The declared vibration and/or noise emission

level represents the main applications of the tool. However

if the tool is used for different applications, with different

accessories or poorly maintained, the vibration and/or

noise emission may differ. This may significantly increase

the exposure level over the total workingperiod.

An estimation of the level of exposure to vibration and/or

noise should also take into account the times when the tool

is switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total workingperiod.

Identify additional safety measures to protect the operator

from the effects of vibration and/or noise such as: maintain

the tool and the accessories, keep the hands warm

(relevant for vibration), organisation of workpatterns.

DCMPH566

Voltage VDC 18

Battery type Li-Ion

SPM 2800

Weight (without battery pack) kg 3,6

Noise values and vibration values (triax vector sum) according to EN62841-1

LPA (emission sound pressure level) dB(A) 81,6

LWA (sound power level) dB(A) 93

K (uncertainty for the given sound

level)

dB(A) 1,2

Vibration emission value a

m/s22,5

Uncertainty K =

m/s21,5

2006/42/EC, EN60745-1 :2010, ISO 10517 :2019.

2000/14/EC, Annex V

DEKRA Certification B.V.

Meander 1051 / P.O. box 5185

6525 MJ ARNHEM / 6802 ED

ARNHEM, Netherlands

LPA (measured sound pressure) 81,6 dB(A)

uncertainty (K) = 3,0 dB (A)

LWA (guaranteed sound power) 95 dB(A)

These products also comply with Directive 2014/30/EU and

2011/65/EU. For more information, please contact

DEWALT

the following address or refer to the back of themanual.

The undersigned is responsible for compilation of the technical

file and makes this declaration on behalf of

DEWALT

Markus Rompel

Vice-President Engineering, PTE-Europe

DEWALT

, Richard-Klinger-Straße 11,

D-65510, Idstein, Germany

10.21.2019

Congratulations!

You have chosen a

DEWALT

tool. Years of experience, thorough

product development and innovation make

DEWALT

one of the

most reliable partners for professional power toolusers.

Technical Data

18V POLE HEDGE TRIMMER

DCMPH566

ENGLISH

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTUREREFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

Batteries Chargers/Charge Times (Minutes)

Cat # VDC Ah Weight (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119

DCB546 18/54 6.0/2.0 1.05 60 270 170 140 90 60 90 X

DCB547 18/54 9.0/3.0 1.46 75* 420 270 220 135* 75* 135* X

DCB548 18/54 12.0/4.0 1.44 120 540 350 300 180 120 180 X

DCB181 18 1.5 0.35 22 70 45 35 22 22 22 45

DCB182 18 4.0 0.61 60/40** 185 120 100 60 60/40** 60 120

DCB183/B 18 2.0 0.40 30 90 60 50 30 30 30 60

DCB184/B 18 5.0 0.62 75/50** 240 150 120 75 75/50** 75 150

DCB185 18 1.3 0.35 22 60 40 30 22 22 22 X

DCB187 18 3.0 0.54 45 140 90 70 45 45 45 90

DCB189 18 4.0 0.54 60 185 120 100 60 60 60 120

*Date code 201811475B or later

**Date code 201536 or later

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non-skid safety shoes, hard hat or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be

caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

ENGLISH

Additional Safety Instructions for

HedgeTrimmers

WARNING: Cutting elements continue to move after the

motor is switchedoff.

• Keep all parts of the body away from the blade. Do not

remove cut material or hold material to be cut when

blades are moving. Blades continue to move after the switch

is turned off. A moment of inattention while operating the

hedge trimmer may result in serious personalinjury.

• Carry the hedge trimmer by the handle with the blade

stopped and taking care not to operate any power

switch. Proper carrying of the hedge trimmer will decrease the

risk of inadvertent starting and resultant personal injury from

theblades.

• When transporting or storing the hedge trimmer, always

fit the blade cover. Proper handling of the hedge trimmer

will decrease the risk of personal injury from theblades.

• When clearing jammed material or servicing the unit,

make sure all power switches are off and the battery

pack is removed or disconnected. Unexpected actuation

of the hedge trimmer while clearing jammed material or

servicing may result in serious personalinjury.

• Hold the hedge trimmer by insulated gripping surfaces

only, because the blade may contact hidden wiring.

Blades contacting a "live" wire may make exposed metal parts

of the hedge trimmer "live" and could give the operator an

electricshock.

• Keep all power cords and cables away from cutting area.

Power cords or cables may be hidden in hedges or bushes and

can be accidentally cut by theblade.

• Do not use the hedge trimmer in bad weather

conditions, especially when there is a risk of lightning.

This decreases the risk of being struck bylightning.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe

injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the

power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

e ) Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk

ofinjury.

f ) Do not expose a battery pack or tool to fire or

excessive temperature. Exposure to fire or temperature

above 130 °C may causeexplosion.

g ) Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging

improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

ENGLISH

Chargers

DEWALT

chargers require no adjustment and are designed to be

as easy as possible tooperate.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your

DEWALT

charger is double insulated in

accordance with EN60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the

DEWALT

serviceorganisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.

WARNING: No connection is to be made to the

earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 3A.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm2; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

Important Safety Instructions for All Battery

Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.

WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.

• To reduce the risk of electrocution, never use the

extended-reach hedge trimmer near any electrical

power lines. Contact with or use near power lines may cause

serious injury or electric shock resulting indeath.

• Always use two hands when operating the extended-

reach hedge trimmer. Hold the extended-reach hedge

trimmer with both hands to avoid loss ofcontrol.

• Always use head protection when operating the

extended-reach hedge trimmer overhead. Falling debris

can result in serious personalinjury.

• Check the hedge for foreign objects, e.g. wirefences.

• The hedge trimmer is intended to be used by the operator

at ground level and not on ladders or any other unstable

support; before operating the hedge trimmer, the user should

make sure the locking device(s) of any moving elements (e.g.

the extended shaft and pivoting element), if any, are in the

lockedposition

• The intended use is described in this instruction manual. The

use of any accessory or attachment or performance of any

operation with this tool other than those recommended in this

instruction manual can present a risk of personal injury and/or

damage toproperty.

• Do not carry the tool with your hands on the front

handle, switch or the trigger switch unless the battery has

beenremoved.

• If you have not used a hedge trimmer before, preferably seek

practical instruction by an experienced user in addition to

studying thismanual.

• Never touch the blades while the tool isrunning.

• Never attempt to force the blades to come to a standstill.

• Do not put the tool down until the blades have come to a

completestandstill.

• Regularly check the blades for damage and wear. Do not use

the tool when the blades aredamaged.

• Take care to avoid hard objects (e.g. metal wire, railings)

when trimming. Should you accidentally hit any such object,

immediately switch the tool off and check for anydamage.

• Should the tool start to vibrate abnormally, immediately switch it off

and remove the battery then check for anydamage.

• If the tool stalls, immediately switch it off. Remove the battery

before attempting to remove anyobstructions.

• After use, place the blade sheath supplied over the blades. Store

the tool, making sure that the blade is notexposed.

• Always ensure that all guards are fitted when using the

tool. Never attempt to use an incomplete tool or a tool with

unauthorisedmodifications.

• Never allow children to use thetool.

• Be aware of falling debris when cutting the higher sides of

ahedge.

• Always hold the tool with both hands and by the

handlesprovided.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

SAVE THESE INSTRUCTIONS

ENGLISH

WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.

CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DEWALT

rechargeable batteries. Other types of

batteries may burst causing personal injury anddamage.

CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging

DEWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard

230V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig. B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack 6 into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button 7 on the batterypack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing tolight.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed

to cool the battery pack. The fan will turn on automatically

when the battery pack needs to be cooled. Never operate the

charger if the fan does not operate properly or if ventilation slots

are blocked. Do not permit foreign objects to enter the interior

of thecharger.

ENGLISH

Battery Packs

Important Safety Instructions for All Battery

Packs

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in

DEWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in locations

where the temperature may fall below 4 ˚C (34 ˚F) (such

as outside sheds or metal buildings in winter), or reach

or exceed 40 ˚C (104 ˚F) (such as outside sheds or metal

buildings insummer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

Electronic Protection System

XR Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium-ion battery

pack on the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

explode in a fire. Toxic fumes and materials are created when

lithium-ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.

WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.

WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.

WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.

CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation

WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from

materials that could contact them and cause a short

circuit. NOTE: Lithium-ion batteries should not be put in

checkedbaggage.

DEWALT

batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road (ADR).

Lithium-ion cells and batteries have been tested to section 38.3

of the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests andCriteria.

In most instances, shipping a

DEWALT

battery pack will be

excepted from being classified as a fully regulated Class 9

Hazardous Material. In general, only shipments containing a

lithium-ion battery with an energy rating greater than 100 Watt

Hours (Wh) will require being shipped as fully regulated Class 9.

ENGLISH

Package Contents

The package contains:

1 Hedge Trimmer

1 Shoulder Strap

1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1, Y1 models)

2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2, Y2 models)

3 Li-Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3, Y3 models)

1 Instruction manual

Battery Type

The following SKU(s) operate on a 18 volt battery pack:

DCMPH566

These battery packs may be used: DCB181, DCB182, DCB183,

DCB183B, DCB184, DCB184B, DCB185, DCB187, DCB189,

DCB546, DCB547, DCB548. Refer to Technical Data for

moreinformation.

All lithium-ion batteries have the Watt Hour rating marked on

the pack. Furthermore, due to regulation complexities,

DEWALT

does not recommend air shipping lithium-ion battery packs

alone regardless of Watt Hour rating. Shipments of tools with

batteries (combo kits) can be air shipped as excepted if the Watt

Hour rating of the battery pack is no greater than 100Wh.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Transporting the FLEXVOLTTM Battery

The

DEWALT

FLEXVOLTTM battery has two modes: Use

andTransport.

Use Mode: When the FLEXVOLTTM battery stands alone or is in

DEWALT

18V product, it will operate as an 18V battery. When

the FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries)

product, it will operate as a 54Vbattery.

Transport Mode: When the cap is attached to the FLEXVOLTTM

battery, the battery is in Transport mode. Keep the cap for

shipping.

When in Transport mode, strings

of cells are electrically

disconnected within the pack

resulting in 3 batteries with a

lower Watt hour (Wh) rating as compared to 1 battery with a

higher Watt hour rating. This increased quantity of 3 batteries

with the lower Watt hour rating can exempt the pack from

certain shipping regulations that are imposed upon the higher

Watt hour batteries.

For example, the Transport

Wh rating might indicate

3x36 Wh, meaning 3

batteries of 36 Wh each.

The Use Wh rating might

indicate 108Wh (1batteryimplied).

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be recharged

beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels

on the charger and the battery pack may show the following

pictographs:

Example of Use and Transport Label Marking

Read instruction manual beforeuse.

See Technical Data for chargingtime.

Do not probe with conductiveobjects.

Do not charge damaged batterypacks.

Do not expose to water.

Have defective cords replacedimmediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indooruse.

Discard the battery pack with due care for

theenvironment.

Charge

DEWALT

battery packs only with designated

DEWALT

chargers. Charging battery packs other

than the designated

DEWALT

batteries with a

DEWALT

charger may make them burst or lead to

other dangeroussituations.

Do not incinerate the batterypack.

USE (without transport cap). Example: Wh rating

indicates 108 Wh (1 battery with 108 Wh).

TRANSPORT (with built-in transport cap). Example:

Wh rating indicates 3 x 36 Wh (3batteries of 36Wh).

ENGLISH

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

WARNING: Use only

DEWALT

battery packs andchargers.

Description (Fig. A)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1 On/Off trigger

2 Lock-off lever

3 Handle

4 Auxiliary handle

5 Motor housing

6 Battery pack

7 Battery release button

8 Threaded sleeve

9 Threaded pole

10 Strap mount

11 Trimmer blade

12 Pivoting trimmer head

13 Trimmer head lock-off button

14 Trimmer head handle

Intended Use

Your

DEWALT

, DCMPH566 hedge trimmer has been designed

for professional landscapingapplications.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

This hedge trimmer is a professional powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear earprotection.

Wear eyeprotection.

Wear headprotection.

Wear protectivegloves.

Wear slip-resistantfootwear.

Beware of fallingobjects.

Do not expose the tool to rain or high

humidity or leave outdoors while it israining.

Switch the tool off. Before performing any

maintenance on the tool, remove the battery

from thetool.

Keep bystandersaway.

Keep hands away fromblade.

Electrocution hazard. Keep at least 10 m away

from overheadlines.

Directive 2000/14/EC guaranteed

soundpower.

NOTE: Battery packs, chargers and kitboxes are not included

with N models. Battery packs and chargers are not included with

NT models. Bmodels include Bluetooth® batterypacks.

NOTE: The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth®, SIG, Inc. and any use of

such marks by

DEWALT

is under license. Other trademarks and

trade names are those of their respectiveowners.

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Date Code Position (Fig. A)

The date code 14, which also includes the year of manufacture,

is printed into thehousing.

Example:

2019 XX XX

Year of Manufacture

ENGLISH

Proper Hand Position (Fig. G)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and

applicableregulations.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Attaching and Adjusting the Shoulder Strap

(Fig. D)

The pole hedge trimmer comes with an adjustable shoulderstrap.

1. Snap the shoulder strap latch17 onto the strap mount10

located on the unit, just in front of the ON/OFF trigger as

shown. Adjust the strap so it fits over yourshoulder.

Joining Trimmer Head Module to Handle

Module (Fig. A, C)

Combining the handle module



15 to the trimmer head

module 21 creates a pole trimmer that is approximately

2.1mlong.

1. Align the groove on the outside of the coupling end of the

handle module15 with the tongue on the inside of the

coupling end of the trimmer head module21.

2. Slide the threaded sleeve8 on the trimmer head module

down as far as possible and rotate the sleeve clockwise until

it stops and completely covers thethreads.

WARNING: Always check to make sure that the sleeve is

completely threaded on and that the threads are no longer

visible. Not threading the sleeve completely on could

result in the modules becoming disconnected creating a

hazardous condition. Periodically check the connections

to insure that no threads arevisible.

Inserting and Removing the Battery Pack

from the Tool (Fig. B)

NOTE: Make sure your battery pack 6 is fullycharged.

To Install the Battery Pack into the Tool Handle

1. Align the battery pack 6 with the rails inside the tool’s

handle (Fig. B).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button 7 and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig. B)

Some

DEWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button 16. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level

of charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Pivoting the Trimmer Head (Fig.E–G)

The trimmer head pivots 180° and can be locked into seven

different positions within that range. To avoid being pinched,

do not grab the blades. Wear gloves and hold unit as shown in

Fig.G.

WARNING: Before connecting the battery to the unit, be

sure the trimmer head is locked intoposition.

To pivot the trimmer head

1. With one hand firmly gripping the trimmer head, use the

other hand to press the lock off button13 and rotate the

trimmer head handle14 to pivot the trimmerhead.

2. Lock the trimmer head into one of the seven operating

positions as shown in Fig. F. To lock the trimmer head into

place, release your grip on the trimmer head handle14.

Check to make sure that trimmer head is locked into

position by trying to move the motor housing. If it is not

locked, rotate it to the nearest lockposition.

Proper hand position requires one hand on the main handle3

and one hand on the auxiliary handle4.

Instructions for Use

WARNING: Always observe the safety instructions and

applicableregulations.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Switching Pole Hedge Trimmer On and Off

(Fig.A)

Ensure the trimmer head is locked into one of the seven

operating positions. Refer To Pivoting the Trimmer

Headsection.

To turn the unit ON, squeeze the lock-off lever2 and then the

On/Off trigger1.

ENGLISH

To turn the unit OFF, release the On/Off trigger and the lock-

offlever.

WARNING: Never attempt to lock the trigger in the

ONposition.

Before Operating Pole Hedge Trimmer

WARNING: The unit has not been designed to provide

protection from electric shock in the event of contact with

overhead electric lines, Consult local regulations for safe

distances from overhead electric power lines and ensure

that the operating position is safe and secure before

operating the extended reach hedgetrimmer.

• For safe operation, read and understand all instructions

before using the pole hedge trimmer. Follow all safety

instructions. Failure to follow all safety instructions listed

below, can result in serious personalinjury.

• Watch what you are doing. Use common sense. Do not

operate pole hedge trimmer when you aretired.

• Only well-instructed adults should operate pole hedge

trimmer. Never allow children tooperate.

• Do not use unit for any job except that for which it

isintended.

• Do not allow children or untrained individuals to use

thisunit.

• Always use an approved hard hat when operating the

pole hedge trimmer overhead. Falling debris can result in

seriousinjury.

• Wear the following safety gear when operating pole

hedgetrimmer:

-head protection

-heavy-duty gloves

-substantial footwear

-safety glasses, goggles or face screen

-face or dust mask (if working in dusty areas)

• Do not wear loose fitting clothing or jewelry of any kind that

could get caught in the moving blades or parts of the pole

hedgetrimmer.

• Secure long hair so it is above shoulder level to prevent

entanglement in any movingparts.

While Operating Pole Hedge Trimmer

• Stay alert. Use common sense while operating theunit.

• Keep work area clean. Cluttered areas inviteinjuries.

• Keep children, animals and bystanders at a safe distance

away from unit. Only the user should be in the workarea.

• Grip unit securely, one hand on the trigger handle, the other

hand on the polehandle.

• Keep finger off trigger until ready touse.

• Before starting unit, make sure blades are not

touchinganything.

• Keep all parts of body away from blades when Pole Hedge

Trimmer isrunning.

• Carry unit from one place to another

-with battery removed

-by holding pole at balance point

-with blade cover in place

• Do not operate in poorlighting.

• During operation, rest periodically and change working

positions to reducefatigue.

• Keep firm footing and balance. Do not overreach.

Overreaching can result in loss of balance or exposure to

sharpsurfaces.

• Do not, under any circumstance, use any attachment or

accessory on this product, which was not provided with

the product, or identified as appropriate for use with this

product in this InstructionManual.

Do Not Operate Pole Hedge Trimmer

• while under the influence of alcohol, medication, ordrugs

• in rain or in damp or wet areas

• where highly flammable liquids or gases are present

• if unit is damaged, adjusted wrong, or not fully and

securelyassembled

• if trigger does not turn unit on and off. Blades must stop

moving when you release trigger. Have faulty switch

replaced by an authorised service centre. SeeMaintenance.

• while in a hurry

• while in tree or on a ladder

• while on aerial booms, buckets or platforms

• during high wind or storming weather

Trimming Instructions (Fig.A, H–L)

DANGER: KEEP HANDS AWAY FROMBLADES.

WARNING: To guard against injury, observe the

following:

• READ INSTRUCTION MANUAL BEFORE USING. SAVE

INSTRUCTIONMANUAL.

• Check the hedge for foreign objects such as wires or

fences before eachuse.

• KEEP HANDS ON HANDLES. DON’TOVERREACH.

• DO NOT USE UNDER WETCONDITIONS.

CAUTION: BLADE MAY COAST AFTER TURNOFF.

NOTE: Jamming the blade on large branches can

causedamage.

WORKING POSITIONS (Fig.H, I) – Maintain proper footing

and balance and do not overreach. Wear safety goggles and

non-skid footwear when trimming. Hold the unit firmly in both

hands and turn the unit on. Always hold the trimmer as shown

in Fig.H and Fig. I, with one hand on the switch handle3 and

one hand on the auxiliary handle4. Never hold the unit by the

trimmer head12.

TRIMMING NEW GROWTH (Fig.J) – Using a wide, sweeping

motion, feeding the blade teeth through the twigs, is most

effective. A slight downward tilt of the blade in the direction of

motion gives the bestcutting.

ENGLISH

Cleaning

WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Lubrication (Fig.A)

Blades

1. After use, carefully clean the blade11 with a resinsolvent.

2. After cleaning, apply a light film of lubrication to the

exposedblade.

3. Turn the trimmer vertical with the blades toward the ground

and run the trimmer for a few seconds to fully disperse

thelubrication.

Maintaining Blade (Fig. M)

The cutting blades are made from high quality, hardened steel

and with normal usage, they will not require resharpening.

However, if you accidentally hit a wire fence, stones, glass, or

other hard objects as shown in Fig. M you may put a nick in the

blade. There is no need to remove this nick as long as it does not

interfere with the movement of the blade. If it does interfere,

remove the battery and use a fine toothed file or sharpening

stone to remove the nick. If you drop the trimmer, carefully

inspect it for damage. If the blade is bent, housing cracked,

Lubrication

Your power tool requires no additionallubrication.

MAINTENANCE

Your power tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regularcleaning.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

LEVEL HEDGES (Fig.K) – To obtain exceptionally level hedges

a piece of string can be stretched along the length of the hedge

as aguide.

SIDE TRIMMING HEDGES (Fig. L) – Orient the trimmer as

shown and begin at the bottom and sweepup.

Guidelines for trimming (U.K. & Ireland)

• Trim hedges and shrubs with seasonal leaves (new leaves

every year) in June andOctober.

• Trim evergreens in April andAugust.

• Trim conifers and other fast growing shrubs every six weeks

from May untilOctober.

Guidelines for trimming (Australia & New

Zealand)

• Trim hedges and shrubs with seasonal leaves (new leaves

every year) in December andMarch.

• Trim evergreens in September andFebruary.

• Trim conifers and other fast growing shrubs every six weeks

from October untilMarch.

handles broken or if you see any other condition that may affect

the trimmer’s operation contact your local

DEWALT

authorised

service centre for repairs before putting it back intouse.

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals. Do not store the unit

on or adjacent to fertilizers orchemicals.

With the battery removed, use only mild soap and a damp

cloth to clean the unit. Never let any liquid get inside the unit;

never immerse any part of the unit into a liquid. Prevent the

blades from rusting by applying a film of light machine oil

aftercleaning.

Blade Sharpening (Fig. N)

• KEEP BLADE SHARP FOR BEST PERFORMANCE. A DULL

BLADE DOES NOT CUTCLEANLY.

• WHEN SHARPENING BLADE, ENSURE THAT BATTERY

ISREMOVED.

REPLACE BENT OR DAMAGED

BLADE IMMEDIATELY

It is recommended that sharpening of blades be performed by

a D

WALT factory service centre. However, blade edges may be

sharpened by using a fine tooth file18.

1. Run the trimmer until cutting blades19 areoffset.

2. Be sure the lock-off lever is engaged, the blade has stopped,

and the battery has been removed before sharpeningblade.

3. Wear proper eye protection and gloves, and be careful not

to cutyourself.

4. Carefully file the cutting edges of the blade with a fine tooth

file. File toward the cutting edge20 at the original cutting

angle (38 degrees from horizontal). File only the straight

cutting edges of the blades. Do not file where the cutting

edge curves into the centre of theblade.

5. Flip the trimmer over to sharpen the bottomblade.

6. Repeat steps to sharpen the opposite side of eachblade.

ENGLISH

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

our environment:

• Run the battery pack down completely, then remove it from

thetool.

• Li-Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

Optional Accessories

WARNING: Since accessories, other than those offered

DEWALT

, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only

DEWALT

recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

PУССКИЙ

ВНИМАНИЕ: Во избежание риска получения травм

ознакомьтесь синструкцией.

Обозначения: правила техники

безопасности

Ниже описывается уровень опасности, обозначаемый

каждым из предупреждений. Прочитайте руководство

иобратите внимание на данныесимволы.

ОПАСНО: Обозначает опасную ситуацию, которая

неизбежно приведет ксерьезной травме или

смертельному исходу, вслучае несоблюдения

соответствующих мербезопасности.

ВНИМАНИЕ: Указывает на потенциально опасную

ситуацию, которая, вслучае несоблюдения

соответствующих мер безопасности,

может привести ксерьезной травме или

смертельномуисходу.

ПРЕДУПРЕЖДЕНИЕ: Указывает на потенциально

опасную ситуацию, которая, вслучае несоблюдения

соответствующих мер безопасности может

стать причиной травм средней или легкой

степенитяжести.

ПОЯСНЕНИЕ: Указывает на практики,

использование которых не связано

сполучением травмы, но если ими пренебречь,

могут привести кпорчеимущества.

Указывает на риск поражения электрическимтоком.

Указывает на рисквозгорания.

Нижеподписавшийся несет ответственность за составление

технической документации и составил данную декларацию

по поручению компании

DEWALT

Маркус Ромпель

Вице-президент по инженерным разработкам, PTE-Europe

DEWALT

, Richard-Klinger-Straße 11,

D-65510, Idstein, Germany

10.21.2019

Декларация о соответствии нормам ЕС

Директива по механическому оборудованию

18 В Аккумуляторный штанговыйкусторез

DCMPH566

DEWALT

заявляет, что продукция, описанная в разделе

«Технические характеристики» соответствует:

2006/42/EC, EN60745-1:2010, ISO 10517:2019.

2000/14/EC, приложение V

DEKRA Certification B.V.

Meander 1051 / P.O. box 5185

6525 MJ ARNHEM / 6802 ED

ARNHEM, Нидерланды

LPA (измеренное звуковое давление) 81,6 дБ(A)

погрешность (K) = 3,0 дБ (A)

LWA (гарантированная акустическая мощность) 95дБ(A)

Эти продукты также соответствуют Директивам 2014/30/EU

и 2011/65/EU. Для получения дополнительной информации

обратитесь в компанию

DEWALT

по адресу, указанному ниже

или приведенному на задней стороне обложкируководства.

DCMPH566

Напряжение В пост. тока 18

Тип батареи Литий-ионная

ход./мин. 2800

Вес (без аккумуляторной батареи) кг 3,6

Значения шума и вибрации (сумма векторов в трех плоскостях) в

соответствии с

EN62841-1

LPA (уровень звукового давления) дБ(A) 81,6

LWA (уровень акустической

мощности)

дБ(A) 93

K (погрешность для заданного

уровня мощности)

дБ(A) 1,2

Значения вибрационного воздействия

м/с22,5

Погрешность K =

м/с21,5

Поздравляем!

Вы приобрели инструмент

DEWALT

. Многолетний опыт,

тщательная разработка изделий иинновации делают

компанию

DEWALT

одним из самых надёжных партнеров для

пользователей профессиональногоэлектроинструмента.

Технические характеристики

18 В АККУМУЛЯТОРНЫЙ ШТАНГОВЫЙ КУСТОРЕЗ

DCMPH566

PУССКИЙ

использовать переходники квилкам для

электроинструментов сзаземлением.

Использование оригинальных штепсельных вилок,

соответствующих типу сетевой розетки снижает

риск поражения электрическимтоком.

b ) Избегайте контакта сзаземленными

поверхностями, такими как трубы,

радиаторы ихолодильники. Если вы будете

заземлены, увеличивается риск поражения

электрическимтоком.

c ) Запрещается оставлять электроинструмент

под дождем ивместах повышенной влажности.

При попадании воды вэлектроинструмент риск

поражения электротокомвозрастает.

d ) Берегите кабель от повреждений. Никогда

не используйте кабель для переноски

инструмента, не тяните за него, пытаясь

отключить инструмент от сети. Держите

кабель подальше от источников тепла, масла,

острых углов или движущихся предметов.

Поврежденный или запутанный кабель питания

повышает риск поражения электрическимтоком.

e ) При работе сэлектроинструментом на

открытом воздухе используйте удлинитель,

подходящий для использования на улице.

Использования кабеля питания, предназначенного

для использования вне помещения, снижает риск

поражения электрическимтоком.

f ) Если использование электроинструмента

вусловиях повышенной влажности неизбежно,

используйте устройства защитного

отключения (УЗО) для защиты сети.

Использование УЗО сокращает риск поражения

электрическимтоком.

3) Обеспечение индивидуальной

безопасности

a ) Будьте внимательны, смотрите, что делаете

ине забывайте оздравом смысле при работе

сэлектроинструментом. Запрещается

работать сэлектроинструментом

ОБЩИЕ ПРАВИЛА ТЕХНИКИ

БЕЗОПАСНОСТИ ПРИ ИСПОЛЬЗОВАНИИ

ЭЛЕКТРОИНСТРУМЕНТОВ

ВНИМАНИЕ: Прочитайте ипросмотрите

все предупреждения, инструкции,

иллюстрации испецификации по данному

электроинструменту. Несоблюдение всех

приведенных ниже инструкций может стать

причиной поражения электрическим током,

возгорания и/или тяжелойтравмы.

СОХРАНИТЕ ВСЕ ИНСТРУКЦИИ ДЛЯ

ПОСЛЕДУЮЩЕГОИСПОЛЬЗОВАНИЯ

Термин «электроинструмент» впредупреждениях

относится кработающим от сети

(проводным) электроинструментам или

работающим от аккумуляторной батареи

(беспроводным)электроинструментам.

1) Безопасность на рабочем месте

a ) Следите за чистотой ихорошим освещением

на рабочем месте. Захламленное или плохо

освещенное рабочее место может стать причиной

несчастногослучая.

b ) Запрещается работать

сэлектроинструментами во

взрывоопасных местах, например, вблизи

легковоспламеняющихся жидкостей, газов

ипыли. Искры, которые появляются при

работе электроинструментов могут привести

квоспламенению пыли илипаров.

c ) Следите за тем, чтобы во время работы

сэлектроинструментом взоне работы

не было посторонних идетей. Отвлекаясь

от работы вы можете потерять контроль

надинструментом.

2) Электробезопасность

a ) Штепсельная вилка электроинструмента

должна соответствовать розетке. Никогда

не меняйте вилку инструмента. Запрещается

Батареи Зарядные устройства/время зарядки (мин)

Кат. № Vпост. тока Ah Вес (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119

DCB546 18/54 6.0/2.0 1.05 60 270 170 140 90 60 90 X

DCB547 18/54 9.0/3.0 1.46 75* 420 270 220 135* 75* 135* X

DCB548 18/54 12.0/4.0 1.44 120 540 350 300 180 120 180 X

DCB181 18 1.5 0.35 22 70 45 35 22 22 22 45

DCB182 18 4.0 0.61 60/40** 185 120 100 60 60/40** 60 120

DCB183/B 18 2.0 0.40 30 90 60 50 30 30 30 60

DCB184/B 18 5.0 0.62 75/50** 240 150 120 75 75/50** 75 150

DCB185 18 1.3 0.35 22 60 40 30 22 22 22 X

DCB187 18 3.0 0.54 45 140 90 70 45 45 45 90

DCB189 18 4.0 0.54 60 185 120 100 60 60 60 120

*Код даты 201811475B или новее

**Код даты 201536 или новее

PУССКИЙ

b ) Не пользуйтесь инструментом, если

не работает выключатель. Любой

инструмент, управлять выключением

ивключением которого невозможно, опасен, иего

необходимоотремонтировать.

c ) Перед выполнением любых настроек,

сменой аксессуаров или прежде чем убрать

инструмент на хранение, отключите его от

сети и/или снимите снего аккумуляторную

батарею, если ее можно снять. Такие

превентивные меры безопасности сокращают риск

случайного включенияэлектроинструмента.

d ) Храните электроинструмент внедоступном

для детей месте ине позволяйте работать

синструментом людям, не имеющим

соответствующих навыков работы стакого

рода инструментами. Электроинструмент

представляет опасность вруках

неопытныхпользователей.

e ) Поддерживайте электроинструмент

ипринадлежности висправном состоянии.

Проверьте, не нарушена ли центровка или

не заклинены ли движущиеся детали, нет

ли повреждений или иных неисправностей,

которые могли бы повлиять на работу

электроинструмента. Вслучае обнаружения

повреждений, прежде чем приступить

кэксплуатации электроинструмента, его

нужно отремонтировать. Большинство

несчастных случаев происходит из-за

электроинструментов, которые не обслуживаются

должнымобразом.

f ) Содержите режущий инструмент востро

заточенном ичистом состоянии. Вероятность

заклинивания инструмента, за которым следят

должным образом икоторый хорошо заточен,

значительно меньше, аработать снимлегче.

g ) Используйте электроинструменты,

принадлежности инасадки всоответствии

сданными инструкциями, принимая во

внимание условия работы ихарактер

выполняемой работы. Использование

электроинструмента для выполнения операций,

для которых он не предназначен, может привести

ксозданию опасныхситуаций.

h ) Все рукоятки иповерхности захватывания

должны быть сухими ибез следов смазки.

Скользкие рукоятки иповерхности захватывания

не позволяют обеспечить безопасность

работы иуправления инструментом

внепредвиденныхситуациях.

5) Использование аккумуляторных

электроинструментов иуход за ними

a ) Используйте для зарядки аккумуляторной

батареи только указанное производителем

зарядное устройство. Использование зарядного

устройства определенного типа для зарядки других

батарей может привести квозгоранию.

всостоянии усталости, наркотического,

алкогольного опьянения или под воздействием

лекарственных препаратов. Невнимательность

при работе сэлектроинструментом может

привести ксерьезным телеснымповреждениям.

b ) Используйте индивидуальные средства

защиты. Всегда используйте защитные очки.

Средства защиты, такие как пылезащитная маска,

обувь снескользящей подошвой, каска изащитные

наушники, используемые при работе, уменьшают

риск получениятравм.

c ) Примите меры для предотвращения

случайного включения. Перед тем как

подключить электроинструмент ксети и/или

аккумуляторной батарее, взять инструмент

или перенести его на другое место, убедитесь

втом, что выключатель находится

вположении «Выкл». Если при переноске

электроинструмента он подключен ксети, ипри

этом ваш палец находится на выключателе, это

может стать причиной несчастныхслучаев.

d ) Уберите все регулировочные или гаечные ключи

перед включением электроинструмента.

Ключ, оставленный на вращающейся части

электроинструмента, может привести ктравме.

e ) Не пытайтесь дотянуться до слишком

удаленных поверхностей. Обувь должна быть

удобной, чтобы вы всегда могли сохранять

равновесие. Это позволит лучше контролировать

электроинструмент внепредвиденныхситуациях.

f ) Одевайтесь соответствующим образом.

Избегайте носить свободную одежду

иювелирные украшения. Следите за тем,

чтобы волосы иодежда не попадали под

движущиеся детали. Возможно наматывание

свободной одежды, ювелирных изделий идлинных

волос на движущиесядетали.

g ) При наличии устройств для подключения

оборудования для удаления исбора пыли

необходимо обеспечить правильность их

подключения иэксплуатации. Использование

устройства для пылеудаления сокращает риски,

связанные спылью.

h ) Не позволяйте хорошему знанию от частого

использования инструментов стать причиной

самонадеянности иигнорирования правил

техники безопасности. Небрежное действие

может повлечь серьезные травмы за долюсекунды.

4) Эксплуатация электроинструмента иуход

за ним

a ) Избегайте чрезмерной нагрузки

электроинструмента. Используйте

электроинструмент всоответствии

сназначением. Правильно подобранный

электроинструмент выполнит работу более

эффективно ибезопасно при стандартнойнагрузке.

Страница загружается ...

DeWalt DCMPH566 Руководство пользователя

Бренд: DeWalt

Модель: DCMPH566

Категория: Триммеры для живой изгороди

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

DeWalt DCMPH566 Руководство пользователя

DeWalt DCMPH566 Руководство пользователя

Похожие модели бренда

Модели других брендов