DeWalt DCH172 Руководство пользователя

Бренд: DeWalt

Модель: DCH172

Категория: Электроинструменты

Тип: Руководство пользователя

DCH172

https://tm.by

Интернет-магазин TM.by

DeWALT

English (original instructions) 4

Pусский (перевод соригинала инструкции) 16

Українська (переклад з оригінальної інструкції) 36

https://tm.by

Интернет-магазин TM.by

Fig. A

Fig. B

XXXX XX XX

https://tm.by

Интернет-магазин TM.by

Fig. C

Fig. E

Fig. G

Fig. D

Fig. F

Fig. H

https://tm.by

Интернет-магазин TM.by

Fig. I

Fig. K

Fig. J

https://tm.by

Интернет-магазин TM.by

ENGLISH

aWARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Denotes risk of electricshock.

Denotes risk offire.

EC‑Declaration of Conformity

Machinery Directive

Heavy-Duty Cordless Rotary Hammerdrill

DCH172

DeWALT

declares that these products described under

Technical Data are in compliance with:

2006/42/EC, EN60745‑1:2009+A11:2010, EN60745‑2‑6:2010.

These products also comply with Directive 2014/30/EU and

2011/65/EU. For more information, please contact

DeWALT

the following address or refer to the back of themanual.

The undersigned is responsible for compilation of the technical

file and makes this declaration on behalf of

DeWALT

Markus Rompel

Vice‑President Engineering, PTE‑Europe

DeWALT

, Richard‑Klinger‑Straße 11,

65510, Idstein, Germany

22.01.2021

Identify additional safety measures to protect the operator

from the effects of vibration and/or noise such as: maintain

the tool and the accessories, keep the hands warm

(relevant for vibration), organisation of workpatterns.

The vibration and/or noise emission level given in this information

sheet has been measured in accordance with a standardised test

given in EN60745

and may be used to compare one tool with

another. It may be used for a preliminary assessment ofexposure.

WARNING: The declared vibration and/or noise emission

level represents the main applications of the tool. However

if the tool is used for different applications, with different

accessories or poorly maintained, the vibration and/or

noise emission may differ. This may significantly increase

the exposure level over the total workingperiod.

An estimation of the level of exposure to vibration and/or

noise should also take into account the times when the tool

is switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total workingperiod.

DCH172

Voltage VDC 18

Type 1

Battery type Li‑Ion

Maximum power output W650

No‑load speed min‑1 0–1060

No‑load beats per min bpm 4980

Single impact energy (EPTA 05/2009) J1.4

Optimum drilling range mm 4–10

Maximum diamter concrete mm 16

Tool holder SDS plus®

Weight (without battery pack) kg 1.8

Noise values and vibration values (triax vector sum) according to EN60745‑2‑6:

LPA (emission sound pressure level) dB(A) 87

LWA (sound power level) dB(A) 98

K (uncertainty for the given sound level) dB(A) 4

Drilling into concrete

Vibration emission value a

h, HD

= m/s28.8

Uncertainty K = m/s21.5

Drilling into metal

Vibration emission value a

h, D

= m/s2≤ 2.5

Uncertainty K = m/s21.5

Screwdriving

Vibration emission value = m/s2≤ 2.5

Uncertainty K = m/s21.5

Congratulations!

You have chosen a

DeWALT

tool. Years of experience, thorough

product development and innovation make

DeWALT

one of the

most reliable partners for professional power toolusers.

Technical Data

English (original instructions)

HEAVYDUTY SDS PLUS® ROTARY HAMMERDRILL

DCH172

https://tm.by

Интернет-магазин TM.by

ENGLISH

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non‑skid safety shoes, hard hat or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off‑position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be

caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust‑relatedhazards.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTUREREFERENCE

The term “power tool” in the warnings refers to your

mains‑operated (corded) power tool or battery‑operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

Batteries Chargers/Charge Times (Minutes)

Cat # VDC Ah Weight (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB116 DCB117 DCB118 DCB132 DCB119

DCB546 18/54 6.0/2.0 1.05 60 270 170 140 90 80 40 60 90 X

DCB547 18/54 9.0/3.0 1.46 75* 420 270 220 135* 110* 60 75* 135* X

DCB548 18/54 12.0/4.0 1.44 120 540 350 300 180 150 80 120 180 X

DCB181 18 1.5 0.35 22 70 45 35 22 22 22 22 22 45

DCB182 18 4.0 0.61 60/40** 185 120 100 60 60/45** 60/40** 60/40** 60 120

DCB183/B/G 18 2.0 0.40 30 90 60 50 30 30 30 30 30 60

DCB184/B/G 18 5.0 0.62 75/50** 240 150 120 75 75/60** 75/50** 75/50** 75 150

DCB185 18 1.3 0.35 22 60 40 30 22 22 22 22 22 40

DCB187 18 3.0 0.54 45 140 90 70 45 45 45 45 45 90

DCB189 18 4.0 0.54 60 185 120 100 60 60 60 60 60 120

*Date code 201811475B or later

**Date code 201536 or later

Batteries

Chargers/Charge Times (Minutes)

Cat #

Weight

*Date code 201811475B or later

**Date code 201536or later

https://tm.by

Интернет-магазин TM.by

ENGLISH

Additional Safety Instructions for

Rotary Hammers

• Wear ear protectors. Exposure to noise can cause

hearingloss.

• Use auxiliary handle(s), if supplied with the tool. Loss of

control can cause personalinjury.

• Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring. Cutting accessory

contacting a "live" wire may make exposed metal parts of the

power tool "live" and could give the operator an electricshock.

• Be certain that the material being drilled does not

conceal electric or gas service and that their locations

have been verified with the utilitycompanies.

• Use clamps or other practical way to secure and support

the workpiece to a stable platform. Holding the work by

hand or against your body is unstable and may lead to loss

ofcontrol.

• Wear safety goggles or other eye protection. Hammering

operations cause chips to fly. Flying particles can cause

permanent eye damage. Wear a dust mask or respirator

for applications that generate dust. Ear protection may be

required for mostapplications.

• Keep a firm grip on the tool at all times. Do not attempt

to operate this tool without holding it with both hands.

It is recommended that the side handle be used at all times.

Operating this tool with one hand will result in loss of control.

Breaking through or encountering hard materials such as

re‑bar may be hazardous as well. Tighten the side handle

securely beforeuse.

• Do not operate this tool for long periods of time.

Vibration caused by hammer action may be harmful to your

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

e ) Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk

ofinjury.

f ) Do not expose a battery pack or tool to fire or

excessive temperature. Exposure to fire or temperature

above 130°C may causeexplosion.

g ) Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging

improperly or at temperatures outside the specified range

may damage the battery and increase the risk offire.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe

injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the

power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

https://tm.by

Интернет-магазин TM.by

ENGLISH

• Connect the blue lead to the neutralterminal.

WARNING: No connection is to be made to the

earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 3A.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm2; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

Important Safety Instructions for All

BatteryChargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.

WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.

WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.

CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable batteries. Other

types of batteries may burst causing personal injury

anddamage.

CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting toclean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging

DeWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

Chargers

DeWALT

chargers require no adjustment and are designed to be

as easy as possible tooperate.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

iYour

DeWALT

charger is double insulated in

accordance with EN60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced only by

DeWALT

or an authorised serviceorganisation.

Mains Plug Replacement

(U.K.& Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

Residual Risks

The following risks are inherent to the use of rotary hammers:

• Injuries caused by touching the rotating parts or hot parts of

thetool.

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of squeezing fingers when changing theaccessory.

• Health hazards caused by breathing dust developed when

working in concrete and/ormasonry.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

hands and arms. Use gloves to provide extra cushion and limit

exposure by taking frequent restperiods.

• Do not recondition bits yourself. Chisel reconditioning

should be done by an authorized specialist. Improperly

reconditioned chisels could causeinjury.

• Wear gloves when operating tool or changing bits.

Accessible metal parts on the tool and bits may get extremely

hot during operation. Small bits of broken material may

damage barehands.

• Never lay the tool down until the bit has come to a

complete stop. Moving bits could causeinjury.

• Do not strike jammed bits with a hammer to dislodge

them. Fragments of metal or material chips could dislodge

and causeinjury.

• Slightly worn chisels can be resharpened bygrinding.

• Do not overheat the bit (discoloration) while grinding

a new edge. Badly worn chisels require reforging. Do not

reharden and temper thechisel.

https://tm.by

Интернет-магазин TM.by

ENGLISH

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing tolight.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed

to cool the battery pack. The fan will turn on automatically

when the battery pack needs to be cooled. Never operate the

charger if the fan does not operate properly or if ventilation slots

are blocked. Do not permit foreign objects to enter the interior

of thecharger.

Electronic Protection System

XR Li‑Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium‑ion battery

pack on the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non‑metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord, the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard

230V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig.B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack 8 into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button 9 on the batterypack.

NOTE: To ensure maximum performance and life of lithium‑ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

FCharging I

GFully Charged J

HHot/Cold Pack Delay* K

https://tm.by

Интернет-магазин TM.by

ENGLISH

CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation

WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from

materials that could contact them and cause a short

circuit. NOTE: Lithium‑ion batteries should not be put in

checkedbaggage.

DeWALT

batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road

(ADR). Lithium‑ion cells and batteries have been tested to

section 38.3of the UN Recommendations on the Transport of

Dangerous Goods Manual of Tests andCriteria.

In most instances, shipping a

DeWALT

battery pack will be

excepted from being classified as a fully regulated Class

9Hazardous Material. In general, only shipments containing a

lithium‑ion battery with an energy rating greater than 100Watt

Hours (Wh) will require being shipped as fully regulated Class 9.

All lithium‑ion batteries have the Watt Hour rating marked on

the pack. Furthermore, due to regulation complexities,

DeWALT

does not recommend air shipping lithium‑ion battery packs

alone regardless of Watt Hour rating. Shipments of tools with

batteries (combo kits) can be air shipped as excepted if the Watt

Hour rating of the battery pack is no greater than 100Wh.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Transporting the FLEXVOLTTM Battery

The

DeWALT

FLEXVOLTTM battery has two modes: Use

andTransport.

Use Mode: When the FLEXVOLTTM battery stands alone or is in

DeWALT

18V product, it will operate as an 18V battery. When

the FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries)

product, it will operate as a 54Vbattery.

Transport Mode: When the cap is attached to the FLEXVOLTTM

battery, the battery is in Transport mode. Keep the cap

forshipping.

Battery Packs

Important Safety Instructions for All

BatteryPacks

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non‑compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in locations

where the temperature may fall below 4˚C (39.2˚F)

(such as outside sheds or metal buildings in winter), or

reach or exceed 40˚C (104˚F) (such as outside sheds or

metal buildings insummer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium‑ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.

WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.

WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.

WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.

https://tm.by

Интернет-магазин TM.by

ENGLISH

Markings on Tool

The following pictograms are shown on the tool:

a Read instruction manual beforeuse.

g Wear earprotection.

f Wear eyeprotection.

n Visible radiation. Do not stare intolight.

Package Contents

The package contains:

1 Cordless rotary hammerdrill

1 Side handle and depth rod

1 Battery Charger

1 Li‑Ion battery pack (C1, D1, G1, L1, M1, P1, S1, T1, X1,

Y1models)

2 Li‑Ion battery packs (C2, D2, G2, L2, M2, P2, S2, T2, X2,

Y2models)

3 Li‑Ion battery packs (C3, D3, G3, L3, M3, P3, S3, T3, X3,

Y3models)

1 Kit box (not included for XE models)

1 Instruction manual

NOTE: Battery packs, chargers and kitboxes are not included

with N models. Battery packs and chargers are not included with

NT models. Bmodels include Bluetooth® batterypacks.

NOTE: The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth®, SIG, Inc. and any use of

such marks by

DeWALT

is under license. Other trademarks and

trade names are those of their respectiveowners.

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Battery Type

The following tools operate on a 18 volt battery pack: DCH172

These battery packs may be used: DCB181, DCB182, DCB183,

DCB183B, DCB183G, DCB184, DCB184B, DCB184G, DCB185,

DCB187, DCB189, DCB546, DCB547, DCB548. Refer to Technical

Data for moreinformation.

y Charge

DeWALT

battery packs only with designated

DeWALT

chargers. Charging battery packs other than

the designated

DeWALT

batteries with a

DeWALT

charger may make them burst or lead to other

dangeroussituations.

z Do not incinerate the batterypack.

B USE (without transport cap). Example: Wh rating

indicates 108Wh (1battery with 108Wh).

A TRANSPORT (with built‑in transport cap). Example: Wh

rating indicates 3x 36Wh (3batteries of 36Wh).

When in Transport mode, strings of cells are electrically

disconnected within the pack resulting in 3batteries with a

lower Watt hour (Wh) rating as compared to 1battery with a

higher Watt hour rating. This increased quantity of 3batteries

with the lower Watt hour rating can exempt the pack from

certain shipping regulations that are imposed upon the higher

Watt hour batteries.

For example, the Transport

Wh rating might indicate

3x36Wh, meaning

3batteries of 36Wh each.

The Use Wh rating might

indicate 108Wh (1batteryimplied).

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be recharged

beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the

labels on the charger and the battery pack may show the

followingpictographs:

LRead instruction manual beforeuse.

p See Technical Data for chargingtime.

q Do not probe with conductiveobjects.

r Do not charge damaged batterypacks.

s Do not expose towater.

t Have defective cords replacedimmediately

u Charge only between 4˚C and 40˚C.

v Only for indooruse.

x Discard the battery pack with due care for

theenvironment.

Example of Use and Transport Label Marking

https://tm.by

Интернет-магазин TM.by

ENGLISH

Lanyard Connection (Fig. A, L)

Optional Accessory

Safety Warnings Specific for Use At Height

WARNING:

If the tool is dropped for any reason the lanyard connection

must be inspected and properly serviced prior to re‑use. The

lanyard connection is designed to stretch to absorb the shock

of a drop. Any permanent stretch to the connection exposing

the red marked internal coils indicates it has been compromised

and must be serviced prior toreuse.

• Do not use hang hook as lanyard attachmentpoint.

Active Vibration Control (Fig. A)

For best vibration control, hold the tool with one hand on the

main handle6 and the other hand on the side handle1. Apply

just enough pressure so the Active Vibration Control10 in the

rear handle are halfway depressed. The hammer only needs

enough pressure to engage the internal active vibration control.

Applying too much pressure will not make the tool drill faster

and active vibration control will notengage.

Electronic Overload Protection

If the drill bit becomes jammed, the power to the drill spindle

will be interrupted by the activation of the electronic overload

protection. To reactivate the power to the drive spindle, the

tool's trigger should be released and then depressed. Due to the

resulting forces, always hold the tool with both hands and take

a firmstance.

To Install the Battery Pack into the Tool Handle

1. Align the battery pack 8 with the rails inside the tool’s

handle (Fig. J).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button 9 and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig.B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button14. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level

of charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end‑userapplication.

Inserting and Removing the Battery Pack

from the Tool (Fig. J)

NOTE: Make sure your battery pack 8 is fullycharged.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

WARNING: Use only

DeWAL

T battery packs andchargers.

Description (Fig. A)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1 Side handle

2 Depth rod

3 Trigger switch

4 Forward/reverse control button (Lock‑off button)

5 Mode selector

6 Main handle

7 Worklight

8 Battery pack

9 Battery release button

10 Active Vibration Control

11 Utility hook

12 Lanyard attachment point

Intended Use

This heavy‑duty cordless rotary hammer is designed for

professional concrete, wood and metal drillingapplications.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

This heavy‑duty cordless rotary hammer is a professional

powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Date Code Position (Fig.B)

The date code 13, which also includes the year of manufacture,

is printed into thehousing.

Example:

2021XX XX

Year and Week of Manufacture

https://tm.by

Интернет-магазин TM.by

ENGLISH

Bit and Bit Holder

WARNING: Burn Hazard. ALWAYS wear gloves when

changing bits. Accessible metal parts on the tool and bits

Utility Hook (Fig. D)

WARNING: To reduce the risk of serious personal

injury, ONLY use the tool’s ultilty hook to hang the

tool from a work belt. DO NOT use the ultilty hook

for tethering or securing the tool to a person or

object during use. DO NOT suspend tool overhead or

suspend objects from the ultilty hook.

WARNING: To reduce the risk of serious personal

injury, ensure the screw holding the ultilty hook

issecure.

IMPORTANT: When attaching or replacing the ultilty hook11,

use only the screw16 that is provided. Be sure to securely

tighten thescrew.

The ultilty hook can be be attached to either side of the tool

using only the screw provided, to accommodate left‑ or right‑

handed users. If the hook is not desired at all, it can be removed

from the tool.

To move ultilty hook, remove the screw that holds the ultilty

hook in place then reassemble on the opposite side. Be sure to

securely tighten thescrew.

Side Handle and Depth Rod (Fig. A, C)

WARNING: To reduce the risk of personal injury, ALWAYS

operate the tool with the side handle properly installed.

Failure to do so may result in the side handle slipping

during tool operation and subsequent loss of control. Hold

tool with both hands to maximizecontrol.

The side handle1 clamps to the front of the gear case and may

be rotated 360˚ to permit right‑ or left‑hand use.

The side handle clamps to the collar15 and has 12tightening

locations. The side handle can be tightened by rotating the

grip of the side handle clockwise. The side handle must be

tightened sufficiently to resist the twisting action of the tool if

the accessory bind or stall. Be sure you moved the side handle

against the end of the collar end to have the clamping piece

fully engaged.

To Adjust the Depth Rod (Fig.A)

Loosen the side handle1 and move the depth rod2 so that

the distance between the end of the rod and the end of the bit

equals the desired drilling depth. When drilling with depth rod,

stop when end of rod reaches surface ofmaterial.

The Lanyard Ready™ Mounting Point12 is for mounting the

DeWALT

Lanyard Ready™ Attachment Point, available at a

DeWALT

servicecenter.

The lanyard‑ready attachment kit is intended for use by

competent personnel who are trained and knowledgeable

regarding working with tools in and around machinery and

“at height”. A lanyard‑ready attachment kit may only be added

to certain models and must be installed by an authorized

servicecenter.

• Only use batteries that contain the integral battery

strap. Do not use unsecured batteries while the tool

is tethered. Unsecured batteries may detach from the

tool ifdropped.

• Always keep the tool and accessories tethered when

working “at height”. (Maximum lanyard length: 6.5

ft [2 m].)

• Use only with lanyards appropriate for this tool type

and rated for at least the weight identified on the tool

lanyard attachment pointlabel.

• Crush, cut or entanglement hazard. Do not use near

moving parts, mechanisms or runningmachinery.

• Do not anchor the tool lanyard to anything on your

body. Anchor to a rigid structure that can withstand

the forces of a droppedtool.

• Make sure the lanyard is properly secure at each end

prior touse.

• Inspect tool and lanyard before each use for damage

and proper function (including fabric and stitching).

Do not use if damaged or not functioningproperly.

• Do not alter the Lanyard Ready™ attachment point

or use in a manner other than as instructed in

thismanual.

• Only attach tool to a lanyard with a locking carabiner.

Do not attach by looping or knotting the lanyard. Do

not use rope orcord.

• Electrical shock hazard. Be sure power is off when

working in high voltage areas. Some lanyards

areconductive.

• Dropped tools will swing on the lanyard, which could

cause injury or loss ofbalance.

• Do not carry the tool by the Lanyard Ready™

attachment point, the battery strap or thelanyard.

• Do not attach more than one tool to eachlanyard.

• Only use appropriate

DeWALT

brand lanyard‑ready

attachment kit. NEVER modify tools to create

attachmentpoints.

• Only transfer the tool between hands while properly

balanced in a stableorientation.

• Do not attach lanyards to tool in a way that keeps

guards, switches or lock‑offs from operatingproperly.

• Avoid getting tangled in thelanyard.

• Keep lanyard away from the cutting area of thetool.

• Do not use lanyards or attachment devices to get

additional leverage from thetool.

• Do not use for personal fallprotection.

• Falling object hazard! Only change batteries,

accesories and attachments where a dropped object

won’t cause a hazard below you. Consult your

Authority Having Jurisdication (AHJ) or site supervisor

for procedures for working atheight.

• Do not use the charger or contractor bag atheight.

• Use multi‑action or screw gate type carabiners. Do not

use single action spring clipcarabiners.

https://tm.by

Интернет-магазин TM.by

ENGLISH

Performing an Application (Fig. A, G)

WARNING: TO REDUCE THE RISK OF PERSONAL

INJURY, ALWAYS ensure workpiece is anchored or

Operation Modes (Fig. G)

WARNING: Do not select the operating mode when the

tool isrunning.

CAUTION: Never use in Rotary Drilling or Rotary

Hammering mode with a chisel bit in the bit holder.

Personal injury and damage to the the tool mayresult.

Your tool is equipped with a mode selector dial5 to selectthe

mode appropriate to desiredoperation.

Symbol Mode Application

Rotary Drilling

Screwdriving

Drilling into steel, wood

andplastics

Rotary Hammering Drilling into concrete

andmasonry

To select an operating mode:

1. Rotate the mode selector dial so that the arrow points to the

symbol corresponding for the desiredmode.

NOTE: The arrow on the mode selector dial5 must be pointing

at a mode symbol at all times. There are no operable positions

inbetween. It may be necessary to briefly run the motor after

having changed from 'hammering only' to 'rotary' modes in

order to align thegears.

Worklight (Fig. A)

CAUTION: Do not stare into worklight. Serious eye

injury couldresult.

There is a worklight7 located on the front of the tool. The

worklight is activated when the trigger switch is depressed, and

will automatically turn off 20seconds after the trigger switch is

released. If the trigger switch remains depressed, the worklight

will remainon.

NOTE: The worklight is for lighting the immediate work surface

and is not intended to be used as aflashlight.

Forward/Reverse Control Button (Fig. F)

A forward/reverse control button4 determines the direction of

bit rotation and also serves as a lock‑offbutton.

To select forward rotation, release the trigger switch3 and

depress the forward/reverse control button on the right side of

thetool.

To select reverse, depress the forward/reverse control button

on the left side of thetool.

The center position of the control button locks the tool in

the off position. When changing the position of the control

button, be sure the trigger isreleased.

NOTE: The first time the tool is run after changing the direction

of rotation, you may hear a click on start up. This is normal and

does not indicate aproblem.

Trigger Switch (Fig. A)

To turn the tool on, squeeze the trigger switch3. To turn the

tool off, release the trigger switch. Your tool is equipped with

a brake. The chuck will stop as soon as the trigger switch is

fullyreleased.

Variable Speed Trigger Switch

The variable speed trigger switch enables you to select the best

speed for a particular application. The farther you squeeze the

trigger switch, the faster the tool will operate. For maximum

tool life, use variable speed only for starting holes orfasteners.

NOTE: Continuous use in variable speed range is not

recommended. It may damage the trigger switch and should

beavoided.

Proper Hand Position (Fig. A, E)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the side handle1,

with the other hand on the main handle6.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and

applicableregulations.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

may get extremely hot during operation. Small bits of

broken material may damage barehands.

The hammerdrill can be fitted with different bits depending on

the desired application. Use sharp drill bitsonly.

Bit Reccomendations

• For wood, use twist bits, spade bits, power auger bits or

holesaws.

• For metal, use high‑speed steel twist drill bits or holesaws.

Use a cutting lubricant when drilling metals. The exceptions

are cast iron and brass which should be drilleddry.

SDS plus® Bit Holder (Fig.H)

NOTE: Special adapters are needed to use the SDS plus® bit

holder with straight shank bits and hexagonal screwdriver bits.

Refer to OptionalAccessories.

To insert a drill bit or other accessory:

1. Insert the shank of the bit about 19mm into SDS plus® tool

holder17.

2. Push and rotate bit until it locks in place. The bit will be

securelyheld.

3. To release bit, pull the sleeve18 back and remove thebit.

https://tm.by

Интернет-магазин TM.by

ENGLISH

Protecting the Environment

wSeparate collection. Products and batteries marked

with this symbol must not be disposed of with

normal householdwaste.

Products and batteries contain materials that

can be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

ourenvironment:

• Run the battery pack down completely, then remove it from

thetool.

• Li‑Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

Dust Extraction System (Fig. F)

The use of a dust extraction system is recommended to reduce

potentially harmful airborne dust and to prolong tool and

accessorylife.

Consult your dealer for further information on suitable dust

extractionsystems.

Optional Accessories

WARNING: Since accessories, other than those offered

DeWALT

, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only

DeWALT

recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Cleaning

WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals

for cleaning the non‑metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Lubrication

Your power tool requires no additionallubrication.

MAINTENANCE

Your power tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regularcleaning.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

The charger and battery pack are notserviceable.

clamped firmly. If drilling thin material, use a wood

“back‑up” block to prevent damage to thematerial.

WARNING: Always wait until the motor has come to

a complete standstill before changing the direction

ofrotation.

1. Choose and install the appropriate chuck, adapter, and/or

bit onto to the tool. Refer to Bit and BitHolder.

2. Using the mode selector dial5, selectthe mode

appropriate to desired application. Refer to

OperationModes.

3. Adjust the side handle1 asnecessary.

4. Select the direction ofrotation using the forward/reverse

button4. When changing the position of the control

button, be sure the trigger isreleased.

‑To select forward rotation, press the for ward/re verse

control button on the right side of thetool.

‑To select reverse, press the forward/reverse control

button on the left side of thetool.

NOTE: The center position of the control button locks

the tool in the offposition.

5. Place the bit/chisel on the desiredlocation.

6. Depress the trigger switch3. The farther you depress

the trigger switch, the faster the tool will operate. For

maximum tool life, use variable speed only for starting holes

orfasteners.

7. To stop the hammer, release theswitch.

Recommendations for Tool Operation

• Large (8 mm to 13mm) holes in steel can be made easier if

a pilot hole (4 mm to 5mm) is drilledfirst.

• When drilling, always apply pressure in a straight line with

the bit, but do not push hard enough to stall the motor or

deflect thebit. A smooth even flow of material indicates the

proper drillingrate.

• If drilling thin material or material that is prone to splinter,

use a wood “back‑up” block to prevent damage to

theworkpiece.

WARNING:

• Do not use this tool to mix or pump easily combustible

or explosive fluids (benzine, alcohol,etc.).

• Do not mix or stir inflammable liquids

labelledaccordingly.

https://tm.by

Интернет-магазин TM.by

ENGLISH

SDS plus® and SDS max® are registered trade marks of

RobertBoschGmbH

https://tm.by

Интернет-магазин TM.by

PУССКИЙ

aВНИМАНИЕ: Во избежание риска получения травм

ознакомьтесь синструкцией.

Декларация о соответствии нормам ЕС

Директива по механическому оборудованию

Аккумуляторный перфоратор высокой

мощности

DCH172

заявляет, что продукция, описанная вТехнические

характеристики, соответствует:

2006/42/EC, EN60745‑1:2009+A11:2010, EN60745‑2‑6:2010.

Эти продукты также соответствуют Директиве 2014/30/EU

и2011/65/EU. За дополнительной информацией

обращайтесь вкомпанию по адресу, указанному ниже или

приведенному на задней стороне обложкируководства.

Нижеподписавшийся несет ответственность за составление

технической документации исоставил данную декларацию

по поручению компании.

Маркус Ромпель

Вице‑президент отдела по разработке ипроизводству,

PTE‑Europe

, Richard‑Klinger‑Straße 11,

D‑65510, Idstein, Германия

22.01.2021

принадлежностями или при ненадлежащем уходе, то

уровень шума и/или вибрации может измениться.

Это может привести к значительному увеличению

уровня воздействия вибрации в течение всего

рабочегопериода.

При расчете приблизительного значения уровня

воздействия шума и/или вибрации также

необходимо учитывать время, когда инструмент

выключен или то время, когда он работает

на холостом ходу. Это может привести к

значительному снижению уровня воздействия

вибрации в течение всего рабочегопериода.

Определите дополнительные меры техники

безопасности для защиты оператора от

воздействия шума и/или вибрации, а именно:

поддержание инструмента и дополнительных

принадлежностей в рабочем состоянии, создание

комфортных условий работы (соответствующих

вибрации), хорошая организация рабочегоместа.

Значение шумовой эмиссии и/или эмиссии вибрации,

указанное в данном справочном листке, было получено

в соответствии со стандартным тестом, приведенным

в EN60745, и может использоваться для сравнения

инструментов. Кроме того, оно может использоваться для

предварительной оценки воздействиявибрации.

ОСТОРОЖНО! Заявленное значение шумовой

эмиссии и/или эмиссии вибрации относится к

основным областям применения инструмента.

Однако, если инструмент используется для

различных целей, с различными дополнительными

DCH172

Напряжение Впост. тока 18

Тип 1

Тип батареи Ионно‑

литиевая

Макс. выходная мощность Вт 650

Скорость без нагрузки об/мин. 0–1060

Частота ударов без нагрузки уд/мин. 4980

Энергия одного удара (EPTA 05/2009) Дж 1,4

Оптимальный диапазон сверления мм 4–10

Максимальный диаметр сверления в бетоне мм 16

Патрон SDS plus®

Вес (без аккумуляторной батареи) кг 1,8

Значения шума и вибрации (сумма векторов в трех плоскостях) в

соответствии с EN60745‑2‑6:

LPA (уровень звукового давления) дБ(A) 87

LWA (уровень акустической мощности) дБ(A) 98

K (погрешность для заданного уровня

мощности)

дБ(A) 4

Сверление в бетоне

Значение вибрационного воздействия a

h, HD

= м/с28,8

Погрешность K = м/с21,5

Сверление металла

Значение вибрационного воздействия a

h, D

= м/с2≤ 2,5

Погрешность K = м/с21,5

Заворачивание

Значение вибрационного воздействия = м/с2≤ 2,5

Погрешность K = м/с21,5

Поздравляем!

Вы приобрели инструмент

DeWALT

. Многолетний опыт,

тщательная разработка изделий иинновации делают

компанию

DeWALT

одним из самых надёжных партнеров для

пользователей профессиональногоэлектроинструмента.

Технические характеристики

Pусский (перевод соригинала инструкции)

SDS PLUS® ПЕРФОРАТОР ВЫСОКОЙ МОЩНОСТИ

DCH172

https://tm.by

Интернет-магазин TM.by

PУССКИЙ

СОХРАНИТЕ ВСЕ ИНСТРУКЦИИ ДЛЯ

ПОСЛЕДУЮЩЕГОИСПОЛЬЗОВАНИЯ

Термин «электроинструмент» впредупреждениях

относится кработающим от сети

(проводным) электроинструментам или

работающим от аккумуляторной батареи

(беспроводным)электроинструментам.

1) Безопасность на рабочем месте

a ) Следите за чистотой ихорошим освещением

на рабочем месте. Захламленное или плохо

освещенное рабочее место может стать причиной

несчастногослучая.

b ) Запрещается работать

сэлектроинструментами во

взрывоопасных местах, например, вблизи

легковоспламеняющихся жидкостей, газов

ипыли. Искры, которые появляются при

работе электроинструментов могут привести

квоспламенению пыли илипаров.

c ) Следите за тем, чтобы во время работы

сэлектроинструментом взоне работы

не было посторонних идетей. Отвлекаясь

от работы вы можете потерять контроль

надинструментом.

2) Электробезопасность

a ) Штепсельная вилка электроинструмента

должна соответствовать розетке. Никогда

не меняйте вилку инструмента. Запрещается

использовать переходники квилкам для

электроинструментов сзаземлением.

Использование оригинальных штепсельных вилок,

соответствующих типу сетевой розетки снижает

риск поражения электрическимтоком.

b ) Избегайте контакта сзаземленными

поверхностями, такими как трубы,

радиаторы ихолодильники. Если вы будете

заземлены, увеличивается риск поражения

электрическимтоком.

ОБЩИЕ ПРАВИЛА ТЕХНИКИ

БЕЗОПАСНОСТИ ПРИ ИСПОЛЬЗОВАНИИ

ЭЛЕКТРОИНСТРУМЕНТОВ

ВНИМАНИЕ: Прочитайте ипросмотрите

все предупреждения, инструкции,

иллюстрации испецификации по данному

электроинструменту. Несоблюдение всех

приведенных ниже инструкций может стать

причиной поражения электрическим током,

возгорания и/или тяжелойтравмы.

Обозначения: правила техники

безопасности

Ниже описывается уровень опасности, обозначаемый

каждым из предупреждений. Прочитайте руководство

иобратите внимание на данныесимволы.

ОПАСНО: Обозначает опасную ситуацию, которая

неизбежно приведет ксерьезной травме или

смертельному исходу, вслучае несоблюдения

соответствующих мербезопасности.

ВНИМАНИЕ: Указывает на потенциально опасную

ситуацию, которая, вслучае несоблюдения

соответствующих мер безопасности,

может привести ксерьезной травме или

смертельномуисходу.

ПРЕДУПРЕЖДЕНИЕ: Указывает на потенциально

опасную ситуацию, которая, вслучае несоблюдения

соответствующих мер безопасности может

стать причиной травм средней или легкой

степенитяжести.

ПОЯСНЕНИЕ: Указывает на практики,

использование которых не связано

сполучением травмы, но если ими пренебречь,

могут привести кпорчеимущества.

Указывает на риск поражения электрическимтоком.

Указывает на рисквозгорания.

Батареи

Зарядные устройства/время зарядки (мин)

Кат. №

пост.тока

Вес

*Код даты 201811475B или новее

**Код даты 201536или новее

Батареи Зарядные устройства/время зарядки (мин)

Кат. № Vпост. тока Ah Вес (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB116 DCB117 DCB118 DCB132 DCB119

DCB546 18/54 6,0/2,0 1,05 60 270 170 140 90 80 40 60 90 X

DCB547 18/54 9,0/3,0 1,46 75* 420 270 220 135* 110* 60 75* 135* X

DCB548 18/54 12,0/4,0 1,44 120 540 350 300 180 150 80 120 180 X

DCB181 18 1,5 0,35 22 70 45 35 22 22 22 22 22 45

DCB182 18 4,0 0,61 60/40** 185 120 100 60 60/45** 60/40** 60/40** 60 120

DCB183/B/G 18 2,0 0,40 30 90 60 50 30 30 30 30 30 60

DCB184/B/G 18 5,0 0,62 75/50** 240 150 120 75 75/60** 75/50** 75/50** 75 150

DCB185 18 1,3 0,35 22 60 40 30 22 22 22 22 22 40

DCB187 18 3,0 0,54 45 140 90 70 45 45 45 45 45 90

DCB189 18 4,0 0,54 60 185 120 100 60 60 60 60 60 120

*Код даты 201811475B или новее

**Код даты 201536 или новее

https://tm.by

Интернет-магазин TM.by

PУССКИЙ

равновесие. Это позволит лучше контролировать

электроинструмент внепредвиденныхситуациях.

f ) Одевайтесь соответствующим образом.

Избегайте носить свободную одежду

иювелирные украшения. Следите за тем,

чтобы волосы иодежда не попадали под

движущиеся детали. Возможно наматывание

свободной одежды, ювелирных изделий идлинных

волос на движущиесядетали.

g ) При наличии устройств для подключения

оборудования для удаления исбора пыли

необходимо обеспечить правильность их

подключения иэксплуатации. Использование

устройства для пылеудаления сокращает риски,

связанные спылью.

h ) Не позволяйте хорошему знанию от частого

использования инструментов стать причиной

самонадеянности иигнорирования правил

техники безопасности. Небрежное действие

может повлечь серьезные травмы за долюсекунды.

4) Эксплуатация электроинструмента иуход

за ним

a ) Избегайте чрезмерной нагрузки

электроинструмента. Используйте

электроинструмент всоответствии

сназначением. Правильно подобранный

электроинструмент выполнит работу более

эффективно ибезопасно при стандартнойнагрузке.

b ) Не пользуйтесь инструментом, если

не работает выключатель. Любой

инструмент, управлять выключением

ивключением которого невозможно, опасен, иего

необходимоотремонтировать.

c ) Перед выполнением любых настроек,

сменой аксессуаров или прежде чем убрать

инструмент на хранение, отключите его от

сети и/или снимите снего аккумуляторную

батарею, если ее можно снять. Такие

превентивные меры безопасности сокращают риск

случайного включенияэлектроинструмента.

d ) Храните электроинструмент внедоступном

для детей месте ине позволяйте работать

синструментом людям, не имеющим

соответствующих навыков работы стакого

рода инструментами. Электроинструмент

представляет опасность вруках

неопытныхпользователей.

e ) Поддерживайте электроинструмент

ипринадлежности висправном состоянии.

Проверьте, не нарушена ли центровка или

не заклинены ли движущиеся детали, нет

ли повреждений или иных неисправностей,

которые могли бы повлиять на работу

электроинструмента. Вслучае обнаружения

повреждений, прежде чем приступить

кэксплуатации электроинструмента, его

нужно отремонтировать. Большинство

c ) Запрещается оставлять электроинструмент

под дождем ивместах повышенной влажности.

При попадании воды вэлектроинструмент риск

поражения электротокомвозрастает.

d ) Берегите кабель от повреждений. Никогда

не используйте кабель для переноски

инструмента, не тяните за него, пытаясь

отключить инструмент от сети. Держите

кабель подальше от источников тепла, масла,

острых углов или движущихся предметов.

Поврежденный или запутанный кабель питания

повышает риск поражения электрическимтоком.

e ) При работе сэлектроинструментом на

открытом воздухе используйте удлинитель,

подходящий для использования на улице.

Использования кабеля питания, предназначенного

для использования вне помещения, снижает риск

поражения электрическимтоком.

f ) Если использование электроинструмента

вусловиях повышенной влажности неизбежно,

используйте устройства защитного

отключения (УЗО) для защиты сети.

Использование УЗО сокращает риск поражения

электрическимтоком.

3) Обеспечение индивидуальной

безопасности

a ) Будьте внимательны, смотрите, что делаете

ине забывайте оздравом смысле при работе

сэлектроинструментом. Запрещается

работать сэлектроинструментом

всостоянии усталости, наркотического,

алкогольного опьянения или под воздействием

лекарственных препаратов. Невнимательность

при работе сэлектроинструментом может

привести ксерьезным телеснымповреждениям.

b ) Используйте индивидуальные средства

защиты. Всегда используйте защитные очки.

Средства защиты, такие как пылезащитная маска,

обувь снескользящей подошвой, каска изащитные

наушники, используемые при работе, уменьшают

риск получениятравм.

c ) Примите меры для предотвращения

случайного включения. Перед тем как

подключить электроинструмент ксети и/или

аккумуляторной батарее, взять инструмент

или перенести его на другое место, убедитесь

втом, что выключатель находится

вположении «Выкл.». Если при переноске

электроинструмента он подключен ксети, ипри

этом ваш палец находится на выключателе, это

может стать причиной несчастныхслучаев.

d ) Уберите все регулировочные или гаечные ключи

перед включением электроинструмента.

Ключ, оставленный на вращающейся части

электроинструмента, может привести ктравме.

e ) Не пытайтесь дотянуться до слишком

удаленных поверхностей. Обувь должна быть

удобной, чтобы вы всегда могли сохранять

https://tm.by

Интернет-магазин TM.by

Страница загружается ...

DeWalt DCH172 Руководство пользователя

Бренд: DeWalt

Модель: DCH172

Категория: Электроинструменты

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

DeWalt DCH172 Руководство пользователя

DeWalt DCH172 Руководство пользователя

Похожие модели бренда

Модели других брендов