V-SPB5.2
13 CM 2-WAY 13 2-
COMPONENT ACOUSTIC SYSTEM
Instruction manual
V-SPB5.2
2
Description
3.6 m (x 8) (x 8)
The set of acoustic system includes:
- acoustic system
- tweeter 2 pcs
- crossover 2 pcs
- metal grill 2 pcs
- speaker wire 3.6 m
- screw 8 pcs
- clip 8 pcs
Important safeguards
· The owners manual contains important operating and maintenance instructions for your safety. It is necessary to refer the manual.
· Do not install the speakers where they may be subjected to excessive heat moisture, dust or where they will be kicked repeatedly, brushed or bumped.
· Before mounting and connecting the wires be sure that wire of the negative pole terminal is disconnected from accumulator. Nonobservance of this
demand may cause the short circuit or fire.
· To prevent short circuit never put or leave any metal objects (e.g. coins or metal tools) inside the acoustic system.
· Make absolutely sure that the terminals for the speakers are connected to the proper outputs from the music source.
· Never run the wiring on the outside of the vehicle or under it where it can be damaged by road hazards or the moving parts of the vehicle. Use existing
wire channels, sills, panels and molding strips inside the vehicle to hide the wiring for safety and a neat appliance.
V-SPB5.2
3
· Make sure the wire of the negative pole terminal is disconnected from accumulator while connecting the speaker terminals. Turn on the various
components and slowly advance the volume. Remember to check and re-check all connections to insure proper installation and use.
· Do not continuously use the speaker system beyond the nominal power handling capacity.
· Keep recorded tapes, watches, and personal credit cards using magnetic coding away from the speaker system to protect them from damage caused by the
magnets in the speakers.
· If you cannot find the appropriate mounting location, consult your car dealer or your nearest dealer before mounting.
CAUTION: Take extreme caution when working near the gas tank, gas lines, brake or hydraulic lines and electrical wiring.
Mounting the speakers
Installation kits are available from your dealer or local stereo shop to help make your installation easy. These kits also give your installation a clean, custom
appearance. Questions about installations methods please consult a professional auto sound dealer/installer for assistance.
· Choose the place of installation for acoustic system. For most acoustic system stipulated regular places in the automobile approach. In this case you need
to know only assembly depth. Before installation acoustic system check up their assembly depth.
· At a choice of a non-standard arrangement of speakers at which it is necessary to cut them in panels of the automobile, use a mould (not included). For
achievement of ideal arrangement of acoustic system keep up geometry of a mould, as it is very important for correct installation of your system
=137 mm, Ø=5 mm).
· If it will be necessary to cut steel, reinstall the cosmetic panel in place and use the hole you have previously cut as a template. This will help to insure
proper cutting and a good fit. Now, mark the locations for the speakers mounting screws, remove the panel and drill the screw holes. When finished you
may replace the panel.
V-SPB5.2
4
· After cutting and drilling all holes, inspect the mounting areas for any metal burrs or rough edges. File any area that may interfere with the mounting of
the speaker.
· Clean any metal shavings from the mounting area and check for areas in which water may enter the speaker cavity. Treat the area for water protection
when necessary.
Securing the speakers
· Position the speaker into the mounting hole and re-confirm the correct mounting location and hole placement.
· Screw clips are provided to ensure a snug fit. These should be placed over the metal surface and line up the hole you have previously drilled with the
screw clip. Place the speaker into the hole, align the holes and proceed to insert the screws. Be sure to tighten the screws evenly so that it will not warp
the speaker frame.
· Turn your system back on and confirm the speakers operation first at a low volume and then you may increase the volume as you desire.
· After installation acoustic system and having tested it the speaker grill will have to be inserted. Turn on you system and follow these steps carefully:
- locate the speaker grill;
- now carefully inspect the place where the speaker grill will be mounted there should be no blowholes;
- fix the speaker grill by screws.
V-SPB5.2
5
Component scheme of connections
Tweeter EQ switch
It is important to wire all the speakers in phase. If after the installations there distinct lack of bass, switch around the POSITIVE & NEGATIVE of one
Midrage/Midbass driver to correct the phasing.
When using very high power amplifiers, do not set the Tweeter EQ switch to +3 dB as you may damage the tweeters.
SWITCH TO LEFT = -3 dB
SWITCH TO CENTER = FLAT
SWITCH TO RIGHT = +3 d
V-SPB5.2
6
If unit fails to operate properly
· Carefully read the instruction to make sure the unit is being operated properly. Check the following before you take your unit to the local dealer for
repair.
SYMPTOM POSSIBLE CAUSE SOLUTION
The volume control regulator set in the
minimal position
Adjust sound level
Bad power connections Check to see that all the power and speaker leads
are securely connected
No sound
The audio source is damaged Take your unit to the local dealer for repair
Acoustic system cables are connected
without observance of polarity (+ or -)
Check to see that all the power and speaker leads
are securely connected
Damage speaker wire or speaker Replace the speaker or speaker wires
The audio source is damaged Take your unit to the local dealer for repair
Unnatural sound
The audio receiver is not Varta Use audio receiver Varta
V-SPB5.2
7
Specification
Loudspeaker one woofer: 13 cm (5.25) Kevlar fiber + paper composite cone
Magnet 10 Oz magnet
Tweeter 25 mm teteron dome
Peak output power 130 W
Rated output power 65 W
Impedance 4 hm
Sensitivity 88 dB
Frequency response 60 22000 Hz
Dimensions 138 x 69 mm
Net / Gross weight 0.89 kg / 3.4 kg
Gift box dimension (L x H x W) 378 mm 300 mm 90 mm
V-SPB5.2
8
3.6 m (x 8) (x 8)
:
-
-
2
- 2
- 2
- 3,6
- 8 .
- 8 .
· .
.
· , , , ,
.
· , (-) .
.
· , (,
) .
· , .
V-SPB5.2
9
· ,
. ,
, , .
· , (-) .
, .
· , .
· ,
, .
· ,
.
: , ,
.
. . ,
, .
· .
. .
.
· , , (
). ,
(=137 , Ø=5 ).
V-SPB5.2
10
· ,
:
- ;
- ;
- ;
- .
· , , . ,
.
· , .
· , .
· ,
. , .
V-SPB5.2
11
· , .
.
· .
:
- ;
- ;
- .
V-SPB5.2
12
. ,
, ,
(). +3dB,
. .
= +3dB
= 0
= -3dB
V-SPB5.2
13
· , ,
. , .
(+ -)
Varta Varta
V-SPB5.2
14
: 13 (5,25)
10 Oz (311 )
25
130
65
4
88
60 22000
138 69
/
0.89 / 3.4
( x x )
378 300 90
/