Whirlpool EUR Руководство пользователя

Gebrauchsanweisung

Instructions for use

Mode d’emploi

Gebruiksaanwijzing

Istruzioni per l’uso

Brugsanvisning

Bruksanvisning

Käyttöohje

Manual de utilização

Instrucciones para el uso

Instrukcje użytkowania

Használati utasítás

ИнструкциЯ за употреба

Návod k použití

Návod na použitie

Instruc∑iuni de utilizare

Инструкции по эксплуатации

3

ENGLISH Instructions for use Page 4

РУCCКИЙ

Инcтpyкции по экcплyaтaции Cтpaницa

28

AMD 343, 344, 345

4

BEFORE USING THE APPLIANCE

To make the most out of your new appliance,

please read the user instructions carefully and keep

them handy for future consultation.

Before using the appliance please follow and

set according to the below indications:

Remote Control (RC) presetting:

Each time the batteries are replaced in the remote

control, the RC is pre-set on Heat pump.

If the air conditioner that you purchased is a

cooling only, then the pre-set on Heat pump will

not bring any changes.

Auto-Restart presetting Function:

To set the auto-restart function, press the

Emergency button (ON/OFF) on the indoor unit

for at least 5 seconds.

A buzz sound will signal that the auto-restart

function is set and the air conditioner is in standby.

To cancel the auto-restart function, repeat the

above steps.

SAFETY PRECAUTIONS

• The Installation and service/repair must be

performed by a qualified technician, in

compliance with the producer's instructions and

following local safety norms. Do not repair or

replace any parts of the appliance unless it is

specifically written in the user instructions.

• Do not pull the power supply cord to remove it

from the socket. Do not twist or press the

power supply cord, and make sure it is not

broken.

• Do not touch the power plug, circuit breaker

and emergency button when your hands are

wet.

• Do not insert your fingers or foreign substances

into the air inlet/outlet of indoor&outdoor unit.

• Never block the air inlet or outlet of indoor and

outdoor unit.

• Physically or mentally disabled people, children

and people without any experience with the

product are only allowed to use the appliance if

they have had specific training on how to

operate the appliance by a person responsible

for their security and well-being. The appliance

is not intended for use by disabled people and

very young children without supervision.

• Children should be supervised to ensure that

they do not play with the appliance (including

remote control).

5

• This appliance has been made of recyclable or

re-usable material. Scrapping must be carried

out in compliance with local waste disposal

regulations. Before scrapping it, make sure to

cut off the mains cord so that the appliance

cannot be re-used.

• For more detailed information on handling and

recycling of this product, contact your local

authorities who deal with the separate collection

of rubbish or the shop where you bought the

appliance.

SCRAPPING OF PACKAGING

• The packaging can be 100% recycled as

confirmed by the recycling symbol . The

various parts of the packaging must not be

dispersed in the environment, but must be

scrapped in line with local authority regulations.

SCRAPPING OF APPLIANCE

• This appliance is marked according to the

European Directive 2002/96/EC, Waste

Electrical and Electronic Equipment (WEEE).

• By ensuring that this product is disposed of

correctly, you will help to prevent potentially

negative consequences for the environment and

for human health.

• The symbol on the product or on the

documents accompanying the product indicates

that this appliance should not be treated as

household waste, but must be given to the

appropriate local gathering place where electric

and electronic appliances are stored and

recycled.

SAFEGUARDING THE ENVIRONMENT

AIR CONDITIONER PRECAUTIONS

Please strictly follow the below instructions:

• Long and direct exposure to cool air might be

harmful to health. It is advisable to set the

louvers in order to avoid direct cool air and

deflect it within the room.

• Upon malfunctioning first turn the appliance off

by pressing the ON/OFF button on the remote

control, then disconnect it from power supply.

• Do not switch the appliance on and off too often

as this can damage the appliance.

• Do not place any objects on the outdoor unit.

• Disconnect the air conditioner from the power

supply if it is to be left unused for a long period

of time or during a thunder/lightning storm.

• This product contains Fluorinated Greenhouse

Gases covered by the Kyoto Protocol, the

refrigerant gas being in a hermetically sealed

system. Refrigerant gas: R410a has a Global

Warming Potential (GWP) 1975.

6

PRODUCT DESCRIPTION

Indoor unit

1. Air Intake

2. Front Panel

3. Display panel

4. Electrical box

5. Air Outlet

6. Emergency button

7. Vertical Adjustment Louver

8. Horizontal Adjustment Louver

9. Air Filter

10. Remote Control

Outdoor unit

11. Air Intake

12. Pipes and Power Connection Cord

13. Drain Hose

Note: Condensate water drains at COOLING

or DRY operation.

14. Air Outlet

Images in the user instructions are based on external views of standard models, shape and design vary

according to the model.

7

CONTROL PANEL DISPLAY INDICATORS

DESCRIPTION

Temperature indicator (1)

Displays set temperature.

Running indicator (2)

It lights up during operation.

It flashes during outside unit defrosting.

Timer indicator (3)

It lights up during the set time.

It goes off when timer operation ends.

Sleep indicator (4)

It lights up during sleep mode.

Compressor indicator (5)

It lights up when the compressor is on.

Signal Receptor (6)

8

REMOTE CONTROL FUNCTIONS

AND INDICATORS

1. ON/OFF BUTTON

Starts and/or Stops the appliance by pressing

this button.

2. MODE BUTTON

Used to select the operation mode.

3. FAN BUTTON

Used to select fan speed in sequence auto,

high, medium or low.

4-5. TEMPERATURE BUTTON

Used to select the room temperature. Used

to set time in timer mode and real time clock.

6. 6TH SENSE BUTTON

Sets or cancels 6th sense operation.

7. SWING BUTTON

Stops or starts vertical adjustment louver

swinging and sets the desired up/down airflow

direction.

8. SLEEP BUTTON

Sets or cancels Sleep Mode operation.

9. AROUND U BUTTON

When you press this button, the remote

control transmits signal of the actual room

temperature around itself to the indoor unit

every 10 minutes. Therefore please keep the

remote control in a location where it can

transmit the signal to the indoor unit properly.

Press once to set and press again to cancel.

10. TIMER ON/CLOCK BUTTON

Used to set the current time.

Used to set or cancel the timer on operation.

11 TIMER OFF BUTTON

Used to set or cancel the timer off operation.

12. JET BUTTON

Used to start or stop the fast cooling.

13. DIM BUTTON

Used to turn on or turn off display light on

indoor unit.

14. POWER SAVE BUTTON

Used to start or stop the power save

operation.

rq

e

t

d

f

i

o

g

s

u

w

y

a

INDICATOR SYMBOLS ON RC DISPLAY

Cooling indicator

Dry indicator

Fan only indicator

Heating indicator

Auto fan speed

High fan speed

Medium fan speed

Low fan speed

6th Sense indicator

Sleep indicator

Around U indicator

Jet indicator

Signal transmission

Display set timer

Display current time

Display set temperature

Power save indicator

O

ON

OFF

STORAGE AND TIPS FOR USING THE

REMOTE CONTROL

How to insert the batteries

1. Insert a pin and gently press down on the

battery cover and push in the direction of the

arrow to remove, as shown.

2. Insert 2 AAA batteries (1.5V) into the

compartment.

Ensure that "+" and "-" polarity is correctly

positioned.

3. Close the battery cover on the remote control.

How to remove the batteries

Remove the battery cover in the direction of the

arrow.

Press the positive pole of the battery softly with

your fingers, then draw the batteries out of the

compartment. All this should be done by adults,

children are forbidden to remove the batteries

from the remote control in order to avoid danger

of swallow.

Disposal of the batteries

Please discard the batteries as sorted municipal

waste at the accessible collection point.

Precautions

• When replacing the batteries, do not use new

batteries with old batteries, or different types of

batteries as this may cause the remote control

to malfunction.

• If you do not expect to use the remote control

for some time, take the batteries out to prevent

leakage of battery acid in the remote control.

• Operate the remote control within effective

range. Keep the remote control at least 1 meter

from any TV set or HI-FI equipment.

• If the remote control does not work normally,

take the batteries out and reinstall after 30

seconds. If it still does not work install new

batteries.

• To operate the appliance by remote control,

point the remote control at the receiving device

on the indoor unit, to ensure receiving

sensibility.

• To send a message from remote control, the

symbol will flash for 1 second. On receipt

of the message, the appliance will emit a beep.

• The remote control will operate the air

conditioner at a distance of up to 7m.

• Each time the batteries are replaced in the

remote control, the remote control is pre-set at

Heat Pump mode.

Signal receptor

9

10

OPERATING MODE DESCRIPTION

Operation Modes:

1. Selecting mode

Each time MODE button is pressed, the operation

mode is changed in sequence:

COOLING → DRY → FAN ONLY → HEATING

↑

Heating mode is not available for cooling only air

conditioners.

2. FAN mode

Each time the "FAN" button is pressed, the fan

speed is changed in sequence:

Auto → High → Medium → Low

↑

At "FAN ONLY" mode, only "High","Medium" and

"Low" are available.

At "DRY" mode, Fan speed is set at "Auto"

automatically, "FAN" button is ineffective in this

case.

3. Setting temperature

Press once to raise temperature setting by 1

raise °C

Press once to lower temperature setting by 1

lower °C

*Note: Heating mode is NOT available for

cooling only models.

4. Turning on

Press button, when the appliance receives

the signal, the RUNNING indicator of the indoor

unit lights up.

During mode changes wait a few seconds and

repeat the operation if the unit does not respond

at once.

When selection the heating operation, air flow will

start after 2-5 minutes.

Range of available set temperature

*HEATING, COOLING 18°C~32°C

DRY +/-2°C

FAN ONLY unable to set

4

1 2

3

11

AIRFLOW DIRECTION CONTROL

5. Airflow direction control

Vertical airflow is automatically adjusted to a

certain angle in accordance with the operation

mode after turning on the unit.

The direction of airflow can be also adjusted to

your own requirement by pressing the "SWING"

button of the remote control.

*Heating mode is only available for heat pump

models.

Vertical airflow control (using the remote

control)

Use the remote control to set the flow angles.

Swinging airflow

Pressing "SWING" button once, the vertical

adjustment louver will swing up and down

automatically.

Desired direction airflow

Pressing the "SWING" button again when the

louvers swing to a suitable angle as desired.

Horizontal airflow control (with hands)

Turn the control rods of the horizontal adjustment

louvers to change horizontal air flow as shown.

Note: The shape of the unit may look different

from that of the air conditioner you have selected.

A - Do not turn the vertical adjustment louvers

manually, otherwise malfunction may occur. If

that happens, turn off the unit first and cut off

the power supply, then restore power supply

again.

B - It is better not to let the vertical adjustment

louver tilt downward for a long time at

COOLING or DRY mode to prevent

condensed water from dripping.

Operation mode Direction of airflow

COOLING, DRY horizontal

*HEATING, FAN ONLY downward

control rod of horizontal

adjustment louvers

12

MODE AND FUNCTION DESCRIPTIONS

6th SENSE MODE

Press the button, the unit enters 6th sense

mode directly regardless of the unit is on or off.

In this mode, temperature and fan speed are

automatically set based on the actual room

temperature.

Operation mode and temperature are

determined by indoor temperature.

Heat pump models

Button is ineffective in Jet mode.

Note: Temperature, airflow and direction are

controlled automatically in 6th sense mode.

However, a decrease or rise of up to 2°C can be

set with the remote control if you still feel

uncomfortable.

What you can do in 6th sense mode

Indoor

temperature

Operation

mode

Target

temperature

21°C or below HEATING 22°C

21°C-23°C FAN ONLY

23°C-26°C DRY

Room

temperature

decrease 1.5°C

after operating

for 3 minutes

Over 26°C COOLING 26°C

Your feeling button adjustment procedure

Uncomfortable because of unsuitable

air flow volume.

Indoor fan speed alternates among High, Medium

and Low each time this button is pressed.

Uncomfortable because of unsuitable

flow direction.

Press it once, the vertical adjustment louver swings

to change vertical airflow direction. Press it again,

swings stops. For horizontal airflow direction please

refer to the chapter "Airflow direction control".

13

Clock function

You can adjust the real time by pressing TIMER

ON/CLOCK button, then using and

buttons to get the correct time, press this button

again, the real time is set.

SLEEP mode

SLEEP mode can be set in COOLING,

HEATING or DRY operation mode.

This function gives you a more comfortable

environment for sleep.

In SLEEP mode,

• The appliance will stop operation automatically

after operating for 8 hours.

• Fan speed is automatically set at low speed.

• Set temperature will rise by max 1°C if the

appliance operates in cooling mode for 1 hour.

• Set temperature will decrease by 3°C at most if

the appliance operates in heating mode for 3

hours.

*Note: In cooling mode, if room temperature is

26°C or above, set temperature will not change.

Note: Heating is NOT available for cooling only air

conditioner.

JET mode

• JET mode is used to start or stop fast cooling or

Heating.

Fast cooling operates at high fan speed, changing

the set temperature automatically to 18°C.

Fast heating operates at auto fan speed,changing

the set temperature automatically to 32 °C.

•In JET mode, you can set airflow direction or

timer. If you want to quit from JET mode, press

any - JET , MODE, FAN, ON/OFF or

TEMPERATURE SETTING button, the display

will return to the original mode.

Note:

• SLEEP and 6th Sense buttons are not available in

JET mode.

• The appliance will continue working in JET mode

if you don't quit from it by pressing any of the

buttons mentioned.

14

Timer function

It is convenient to set the timer on by pressing the

TIMER ON/CLOCK button to achieve a

comfortable room temperature at the time you get

home.

You can also set timer off by pressing the TIMER

OFF button to enjoy a good sleep at night.

How to set TIMER ON

TIMER ON/CLOCK button can be used to set the

timer programming as wished in order to switch on

the appliance at your desired time.

i) Press TIMER ON/CLOCK button for 3 seconds,

when "ON 12:00" flashes on the LCD, then you

can press the or buttons to select your

desired time for appliance on.

Press the or button once to increase or

decrease the time setting by 1 minute.

Press the or button for 5 seconds to

increase or decrease the time setting by 10

minutes.

Press the or button for a longer time to

increase or decrease the time by 1 hour.

Note: If you don't see the time in 10 seconds after

you press TIMER ON/CLOCK button, the remote

control will exit the TIMER ON mode

automatically.

ii) When your desired time displayed on LCD,

press the TIMER ON/CLOCK button and confirm

it.

A "beep" can be heard.

"ON" stops flashing.

The TIMER indicator on the indoor unit lights up.

iii) After the time set displayed for 5 seconds the

clock will be displayed on the LCD of the remote

control instead of set timer.

How to cancel TIMER ON

Press the TIMER ON/CLOCK button again, a

"beep" can be heard and the indicator disappears,

the TIMER ON mode has been canceled.

Note: It is similar to set the TIMER OFF, you can

make the appliance switch off automatically at your

desired time.

OON

Increase

Decrease

15

Around U function

When you press this button, will display,

remote control transmits the actual room

temperature around it to the indoor unit, and the

appliance will operate according to this

temperature to let you feel more comfortable.

Please keep the remote control in a location where

it can transmit the signal to the indoor unit

properly.

Press once to set and press again to cancel.

DIM function

Press this button to turn on or turn off display light

on indoor unit control panel.

POWER SAVE function

POWER SAVE mode can be available in

COOLING, HEATING, DRY and FAN ONLY

operation mode.

When pressing this button, will display on

remote control.

POWER SAVE function under COOLING,

HEATING and DRY mode, the appliance will set

the temperature at 25°C with low fan speed.

POWER SAVE function under FAN ONLY mode:

the appliance will set at low fan speed.

Change mode or press the power save button

again to cancel this function.

Note: Fan speed and temperature can not be

adjusted under this mode.

16

MAINTENANCE

Unit

1. Unplug from the power supply

Turn off the appliance first before disconnecting

from power supply.

2. To remove the front panel pull it outwards

(Fig. A).

3. Wipe with a soft and dry cloth.

Use lukewarm water (below 40°C) to clean if

the appliance is very dirty.

4. Refit and close the front panel (Fig. B).

Refit and close the front panel by pushing it

downward.

Note:

• Do not use substances such as gasoline or

polishing powder to clean the appliance.

• Do not sprinkle water onto the indoor unit

Dangerous! Electric shock!

Air filter

It is necessary to clean the air filter after using it

for about 100 hours.

Clean the air filter every two weeks if the air

conditioner operates in an extremely dusty

environment.

1. Unplug from the power supply

Turn off the appliance first before disconnecting

from power supply and remove the air filter.

1. Open the front panel.

2. Press the handle of the filter gently.

3. Slide out the filter.

2. Cleaning and refitting the air filter.

If the filter is very dirty, clean it with a solution

of lukewarm water and neutral detergent.

After cleaning let it dry.

3. Close the front panel.

Note:

• To avoid injury, do not touch the fins of

indoor unit with your fingers after

removing the filter.

• Do not attempt to clean the inside of the

air conditioner by yourself.

• Do not clean the filter in washing machine.

Fig. A

Fig. B

17

PROTECTION

Operating condition

The protective device maybe trip and stop the

appliance in the cases listed below.

* For Tropical (T3) Climate condition models, the

temperature point is 52°C instead of 43°C.

If the air conditioner runs in COOLING or DRY

mode with door or window opened for a long

time when relative humidity is above 80%, dew

may drip down from the outlet.

Noise pollution

• Install the air conditioner at a place that can bear

its weight in order to operate more quietly.

• Install the outdoor unit at a place where the air

discharged and the operation noise would not

annoy your neighbours.

• Do not place any obstacles in front of the air

outlet of the outdoor unit lest it increases the

noise level.

Features of protection device

1. Protection device

Wait at least 3 minutes before restarting the unit

after operation stops or changing mode during

operation.

After connecting to power supply and turning on

the appliance immediately, a delay of 20 seconds

may occur before it starts to operate.

2. If all operation has stopped, press ON/OFF

button again to restart. Timer should be set

again if it has been cancelled.

Features of HEATING mode

Preheating

2-5 minutes are necessary to preheat the indoor

unit at HEATING operation start.

Defrosting (out door unit)

In HEATING operation the appliance will defrost

(de-ice) automatically to raise efficiency.

This procedure usually lasts 2-10 minutes. During

defrosting, fan stops operation.

After defrosting completes, it returns to

HEATING mode automatically.

Note: Heating is NOT available for cooling only

air conditioner models.

HEATING

Outdoor air temperature is over 24°C

Outdoor air temperature is below -7°C

Room temperature is over 27°C

COOLING

Outdoor air temperature is over *43°C

Room temperature is below 21°C

DRY Room temperature is below 18°C

EMERGENCY OPERATION

Under emergency situation or when remote

control is missing, you can control the unit by

pressing the emergency button located on the

indoor unit.

• Turn on the appliance: when the unit is off, press

this button, it will start up.

• Turn off the appliance: when the unit is on, press

this button, the unit will stop working.

7

Emergency button

Operation problems are often due to minor causes, please check and refer to the

following chart before contacting the service. This may save time and unnecessary

expenses.

Note: If the problems still have, turn off the appliance and disconnect from power supply,

then contact the nearest Whirlpool Authorized Service Center. Do not attempt to move,

repair, disassemble, or modify the appliance by yourself.

18

TROUBLESHOOTING

Trouble Analysis

Does not run

• Is the protection device or fuse blown?

• Please wait for 3 minutes and start again, protection device may be preventing

unit to work.

• Are the RC batteries low?

• Is the plug not properly plugged?

No cooling or

heating air

• Is the air filter dirty?

• Are the intakes and outlets of the air conditioner blocked?

• Is the temperature set properly?

Ineffective control

• Has there been a strong interference (from excessive static electricity discharge,

power supply voltage abnormality)? Note that operation will be abnormal, in this

case unplug from the power supply and re-plug after 2-3 seconds.

Does not operate

immediately

• 3 minute delay will occur when changing mode during operation.

Peculiar smell

• This smell may come from another source such as furniture, cigarette etc, which

is sucked in the unit and blown out with the air.

A sound of running

water

• Normal behaviour caused by the flow of refrigerant in the air conditioner.

• Defrosting sound in heating mode.

Cracking sound

• The sound may be generated by the expansion or contraction of the front panel

due to temperature changes.

Mist sprays from

the outlet

• Mist is present in the room with low temperature? Normal behaviour due to

cool air discharged from indoor unit during COOLING or DRY operation

mode.

19

INSTALLATION INSTRUCTIONS

Installation diagram

NOTE: The figure above is only a simple presentation of the unit, it may not match the external

appearance of the product you purchased. Installation must be performed in accordance with the national

wiring standards by authorized service people only.

Distance from wall

should be over 50mm

Distance from ceiling

should be over 50mm

Distance from floor

should be over 2000mm

Distance from the wall

should be over 50mm

Air intake distance from

the wall should be over

250mm

Air intake distance from

the wall should be over

250mm

Air outlet distance from the wall

should be over 500mm

Over 250mm

20

Select the best location

Location for Installing Indoor Unit

• Where there is no obstacle near the air outlet

and air can be easily blown to every corner.

• Where piping and wall hole can be easily

arranged.

• Observe the required distance from ceiling and

wall according to the wiring diagram.

• Where the air filter can easily be removed.

• Keep the unit and remote control 1m or more

from television, radio etc.

• To prevent the effects of a fluorescent lamp,

keep the unit as far as possible from it.

• Do not put anything near the air inlet that could

obstruct it.

• In a place that can bear the weight and will not

increase operating noise and vibrations.

Location for Installing Outdoor Unit

• Install in a convenient and well-ventilated place.

• Avoid installing it where flammable gas could

leak.

• Observe the required distance from the wall.

• The distance between Indoor and outdoor unit

should be 5 meters and can go up to maximum

15 meters with additional refrigerant charge.

• Do not install the outdoor unit in a dirty or

greasy place, near a vulcanization gas exit.

• Avoid installing it at the roadside where it could

be soiled with muddy water.

• A fixed base where operating noise will not

increase.

• Where the air outlet is not obstructed.

Model Max. Allowable

Tubing Length at

Shipment (m)

Limit of Tubing

Length (m)

Limit of Elevation

Difference H (m)

Required amount

of additional

refrigerant (g/m)

7K~18K 5 15 5 20

Indoor unit

Pipe length is

15 meters Max.

Outdoor unit

Height should

be less than 5m

Outdoor unit

Pipe length is

15 meters Max.

Indoor unit

Height should be less

than 5m

Страница загружается ...

Whirlpool EUR Руководство пользователя

Это руководство также подходит для

Whirlpool EUR Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов