Sony MDS-JE520 Инструкция по применению

Категория
Минидисковые плееры
Тип
Инструкция по применению
Operating Instructions
Instrukcja obsługi
Инструкция по эксплуатации
3-862-735-62(1)
1998 by Sony Corporation
MiniDisc Deck
MDS-JE520
S
MiniDisc Deck
MDS-JE520
EN
PL
RF
P
2
EN
WARNING
To prevent fire or shock
hazard, do not expose the unit
to rain or moisture.
To avoid electrical shock, do
not open the cabinet. Refer
servicing to qualified
personnel only.
The laser component in this product
is capable of emitting radiation
exceeding the limit for Class 1.
This appliance is classified as a CLASS 1
LASER product. The CLASS 1 LASER
PRODUCT MARKING is located on the
rear exterior.
The following caution label is located
inside of the unit.
IN NO EVENT SHALL SELLER BE
LIABLE FOR ANY DIRECT,
INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR
EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR
THE USE OF ANY PRODUCT.
Precautions
On safety
Should any solid object or liquid fall
into the cabinet, unplug the deck and
have it checked by qualified personnel
before operating it any further.
On power sources
Before operating the deck, check that
the operating voltage of the deck is
identical with your local power
supply. The operating voltage is
indicated on the nameplate at the rear
of the deck.
The unit is not disconnected from the
AC power source (mains) as long as it
is connected to the wall outlet, even if
the unit itself has been turned off.
If you are not going to use the deck
for a long time, be sure to disconnect
the deck from the wall outlet. To
disconnect the AC power cord, grasp
the plug itself; never pull the cord.
AC power cord must be changed only
at the qualified service shop.
On operation
If the deck is brought directly from a
cold to a warm location, or is placed in a
very damp room, moisture may
condense on the lenses inside the deck.
Should this occur, the deck may not
operate properly. In this case, remove
the MD and leave the deck turned on
for about an hour until the moisture
evaporates.
On the MiniDisc cartridge
Do not open the shutter to expose the
MD.
Do not place the cartridge where it
will be subject to extremes of
sunlight, temperature, moisture or
dust.
On cleaning
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzine.
If you have any questions or problems
concerning your deck, please consult
your nearest Sony dealer.
Welcome!
Thank you for purchasing the Sony
MiniDisc Deck. Before operating the
deck, please read this manual
thoroughly and retain it for future
reference.
About This Manual
Conventions
Controls in the instructions are those
on the deck; these may, however, be
substituted by controls on the remote
that are similarly named or, when
different, appear in the instructions
within brackets.
The following icons are used in this
manual:
Z
Indicates a procedure that
requires use of the remote.
z
Indicates tips for making the
task easier and hints.
EN
3
EN
TABLE OF CONTENTS
Getting Started
Unpacking ........................................................................................................................... 4
Hooking Up the System.................................................................................................... 4
Recording on an MD .......................................................................................................... 6
Playing an MD ....................................................................................................................... 8
Recording on MDs
Notes on Recording ........................................................................................................... 9
Useful Tips for Recording ............................................................................................... 10
Recording Over Existing Tracks..................................................................................... 11
Adjusting the Recording Level....................................................................................... 12
Marking Track Numbers While Recording (Track Marking) ................................... 13
Starting Recording With 6 Seconds of Prestored Audio Data
(Time Machine Recording) .......................................................................................... 14
Synchro-Recording With Audio Equipment of Your Choice
(Music Synchro-Recording)......................................................................................... 15
Synchro-Recording With a Sony CD Player................................................................. 16
Fading In and Out (Fader)............................................................................................... 17
Recording on an MD Using a Timer.............................................................................. 18
Playing MDs
Using the Display.............................................................................................................. 19
Locating a Specific Track ................................................................................................. 20
Locating a Particular Point in a Track ........................................................................... 21
Playing Tracks Repeatedly .............................................................................................. 22
Playing in Random Order (Shuffle Play) ...................................................................... 23
Creating Your Own Program (Program Play) ............................................................. 23
Useful Tips When Recording From MDs to Tape ....................................................... 25
Fading In and Out (Fader)............................................................................................... 26
Playing an MD Using a Timer ........................................................................................ 26
Falling Asleep to Music ................................................................................................... 27
Editing Recorded MDs
Notes on Editing ............................................................................................................... 28
Erasing Recordings (Erase Function) ............................................................................ 28
Erasing a Part of a Track (A-B Erase Function) ........................................................... 30
Dividing Recorded Tracks (Divide Function).............................................................. 31
Combining Recorded Tracks (Combine Function) ..................................................... 32
Moving Recorded Tracks (Move Function).................................................................. 33
Labeling Recordings (Title Function) ............................................................................ 33
Undoing the Last Edit (Undo Function) ....................................................................... 37
Additional Information
Display Messages.............................................................................................................. 38
System Limitations ........................................................................................................... 38
Troubleshooting ................................................................................................................ 39
Specifications ..................................................................................................................... 40
Guide to the Serial Copy Management System ........................................................... 41
Index.................................................................................................................................... 42
Table of Setup Menus....................................................................................................... 44
Self-Diagnosis Function ................................................................................................... 45
Getting Started
4
EN
çç
çç
ç: Signal flow
What cords will I need?
Audio connecting cords (supplied) (2)
Optical cables (only one supplied) (2)
Coaxial digital connecting cable (not supplied) (1)
Getting Started
Hooking Up the System
Overview
This section describes how to hook up the MD deck to
an amplifier or other components such as a CD player
or DAT deck. Be sure to turn off the power of each
component before connection.
to a wall outlet
(or to a timer during timer
recording or playback)
You can
connect two
digital
components
at a time.
White
(L)
Red
(R)
White
(L)
Red
(R)
Amplifier
CD player
CD player, DAT deck,
or MD deck, etc.
Unpacking
Check that you received the following items:
Audio connecting cords (2)
Optical cable (1)
Remote commander (remote) RM-D15M (1)
Sony R6 (size-AA) batteries (2)
Inserting batteries into the remote
You can control the deck using the supplied remote.
Insert two R6 (size-AA) batteries by matching the +
and – on the batteries. When using the remote, point it
at the remote sensor g on the deck.
z When to replace batteries
With normal use, the batteries should last for about six
months. When the remote no longer operates the deck,
replace all the batteries with new ones.
Notes
Do not leave the remote near an extremely hot or humid
place.
Do not drop any foreign object into the remote casing,
particularly when replacing the batteries.
Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a malfunction.
If you don’t use the remote for an extended period of time,
remove the batteries to avoid possible damage from
battery leakage and corrosion.
ç
ç
ç
ç
ç
REC
OUT
TAPE
IN
DIGITAL
COAXIAL OUT
DIGITAL
OPTICAL OUT
DIGITAL
OPTICAL IN
LINE
R
L
DIGITAL
OUTIN
(ANALOG)
OUT
IN
OPTICAL
IN
COAXIAL
5
EN
Getting Started
Hookups
Connecting the deck to an amplifier
Connect the amplifier to the LINE (ANALOG) IN/
OUT jacks using the audio connecting cords (supplied),
making sure to match the color-coded cords to the
appropriate jacks on the components: red (right) to red
and white (left) to white. Be sure to make connections
firmly to prevent hum and noise.
çç
çç
ç: Signal flow
Connecting the deck to a digital component such as
a CD player, DAT deck, digital amplifier, or another
MD deck
Connect the component through the DIGITAL
OPTICAL IN/OUT or DIGITAL COAXIAL IN
connectors with two optical cables (only one supplied)
and/or a coaxial digital connecting cable (not
supplied).
When using the optical cables
Take the caps off the connectors and then insert the plugs
parallelly until they click into place.
Be sure not to bend or tie together the optical cables.
çç
çç
ç: Signal flow
When using the coaxial digital connecting cable
çç
çç
ç: Signal flow
Note
If the optical cables and/or the coaxial digital connecting
cable are not connected properly, “Din Unlock” and “C71”
may alternate in the display.
MD deck
Amplifier
ç
Ç
L
R
L
R
LINE
(ANALOG)
OUTIN
TAPE / MD
INOUT
z Automatic conversion of digital sampling rates
during recording
A built-in sampling rate converter automatically
converts the sampling frequency of various digital
sources to the 44.1 kHz sampling rate of your MD deck.
This allows you to record sources such as 32- and 48-
kHz DAT or satellite broadcasts, as well as compact
discs and other MDs.
Note
If “Din Unlock” alternates with “C71”, or “Cannot Copy”
appears in the display, recording through the digital
connector is not possible. In this case, record the program
source through the LINE (ANALOG) IN jacks with the
INPUT switch set at ANALOG.
Connecting the AC power cord
Connect the AC power cord to a wall outlet or to the
outlet of a timer.
MD deck
Digital component
MD deck
Digital component
DIGITAL
OUTIN
OPTICAL
DIGITAL
OUT
ININ
OPTICAL
COAXIAL
ç
Ç
DIGITAL
COAXIAL
Ç
OUT
DIGITAL
OUT
ININ
OPTICAL
COAXIAL
Basic Operations
6
EN
With the label side up
With the arrow pointing this way
Recording on an MD
1
Turn on the amplifier and play the program source you want
to record.
2
Press 1/u.
The STANDBY indicator turns off.
3
Insert a recordable MD.
If the MD has a recorded material on it, the deck will
automatically start recording from the end of the last recorded
track.
4
Set INPUT to the corresponding input connector.
To record through Set INPUT to
DIGITAL OPTICAL IN OPT
DIGITAL COAXIAL IN COAX
LINE (ANALOG) IN ANALOG
5
Set REC MODE to the mode you want to record in.
To record in Set REC MODE*
1
to
Stereo sound STEREO
Monaural sound*
2
MONO
*
1
If you switch REC MODE during recording or recording pause, recording
stops.
*
2
In the monaural recording, you can record about two times longer than in
the stereo recording.
Monitor audio during recording
Even if you set REC MODE to
MONO, the monitor signal does
not become monaural.
±
REC
INPUT
MONO
PHONES
PHONE LEVEL
PLAY MODE
SCROLL
AMS
YES
MENU/
NO
TIMER
REC OFF PLAY
LEVEL/
DISPLAY/CHAR
REC MODE
p
0
)
r
MIN
MAX
·
§
OPT
EJECT
STANDBY
TIMEREPEAT
STEREO
FADER
CLEAR
COAX
ANALOG
PUSH ENTER
P
27
3
7
86
5
4
Basic Operations
Basic Operations
7
EN
6
Press r REC.
The deck becomes ready to record.
7
Press LEVEL/DISPLAY/CHAR to change the display, then
turn AMS to adjust the recording level.
For details, see pages 12 and 13.
8
Press · or P.
Recording starts.
9
Start playing the program source.
Do not disconnect the deck from the power source immediately after
recording
If you do, recorded material may not be saved to the MD. To save the
material, after recording, press § EJECT to take out the MD or change the
deck to standby by pressing 1/u. “TOC Writing” will flash in the display at
this time.
After “TOC Writing” stops flashing and goes out, you can pull out the AC
power cord.
To Press
Stop recording p
Pause recording* P. Press the button again or press · to resume
recording.
Take out the MD § EJECT after stopping
* Whenever you pause recording, the track number increases by one. For example, if
you paused recording while recording on track 4, the track number increases by
one and recording continues on the new track when restarted.
To protect an MD against accidental erasure
To make it impossible to record on an MD, slide the tab in the direction of
arrow, opening the slot. To allow recording, close the slot.
Rear of the disc
Record-protect tab
Slide the tab in the
direction of arrow
When “TOC Writing” flashes in
the display
The deck is currently updating the
Table Of Contents (TOC). Do not
move the deck or pull out the AC
power cord. Changes to an MD
made through recording are saved
only when you update the TOC by
ejecting the MD or changing the
deck to standby by pressing the
1/u switch.
Basic Operations
8
EN
Playing an MD
1
Turn on the amplifier and set the source selector to the position
for MD deck.
2
Press 1/u.
The STANDBY indicator turns off.
3
Insert an MD.
4
Press ·.
The deck starts playing. Adjust the volume on the amplifier.
To Do the following:
Stop playing Press p.
Pause playing Press P. Press the button again or press
· to
resume playing.
Go to the next track Turn AMS clockwise (or press + on the
remote).
Go to the current track Turn AMS counterclockwise (or press = on the
or the preceding track remote).
Take out the MD Press § EJECT after stopping playing.
z You can locate and play back
a track while the deck is
stopped
1 Turn AMS (or press = or
+) until the number of the
track you want to play
appears.
2 Press AMS or ·.
z To use headphones
Connect them to PHONES jack.
Use PHONE LEVEL to adjust
the volume.
z You can adjust the analog
signal level output to the
LINE (ANALOG) OUT jacks
1 While the deck is playing,
press LEVEL/DISPLAY/
CHAR repeatedly until the
line output adjustment
display appears.
2 Turn AMS (or press LEVEL
+/–) to adjust the output
signal level.
Notes
The output level for the
PHONES jack is also
changed.
When you eject the MD or
turn off the power by
pressing the 1/u switch, the
output level is reset to the
initial setting (0.0dB).
With the label side up
With the arrow pointing this way
±
REC
INPUT
MONO
PHONES
PHONE LEVEL
PLAY MODE
SCROLL
AMS
YES
MENU/
NO
TIMER
REC OFF PLAY
LEVEL/
DISPLAY/CHAR
REC MODE
Pp
0
)
r
MIN
MAX
·
§
OPT
EJECT
STANDBY
TIMEREPEAT
STEREO
FADER
CLEAR
COAX
ANALOG
PUSH ENTER
234
9
EN
Recording on MDsRecording on MDs
When recording from DAT or satellite broadcasts
with the INPUT switch set at the respective digital
position, the deck automatically marks a track
number whenever the sampling frequency of the
input signal changes regardless of the Setup Menu 02
setting.
z You can mark track numbers during or after
recording
For details, see “Marking Track Numbers While
Recording” (page 13) and “Dividing Recorded Tracks”
(page 31).
When “TOC Writing” flashes in the display
The deck is currently updating the Table Of Contents
(TOC). Do not move the deck or pull out the AC
power cord. Changes to an MD made through
recording are saved only when you update the TOC by
ejecting the MD or changing the deck to standby by
pressing the 1/u switch.
The MD deck uses the SCMS (Serial Copy
Management System on page 41)
MDs recorded through digital input connector cannot
be copied onto other MDs or DAT tapes through the
digital output connector.
When the deck is recording or in recording pause,
digital signals input through one of the digital input
connectors are output to the DIGITAL OPTICAL OUT
connector with the same sampling rate
To change the digital input signal to another sampling
rate for output (without recording it to an MD), use
Input Monitor Function (see page 10).
Notes on Recording
If “Protected” alternates with “C11” in the display
The MD is record-protected. Close the slot to record
on the disc (see “To protect an MD against accidental
erasure” on page 7).
If “Din Unlock” alternates with “C71” in the display
The digital program source is not connected as you
set with the INPUT switch in Step 4 on page 6.
To continue, connect the program source properly.
The program source is not on.
Turn on the program source.
Depending on the menu settings and source being
recorded, track numbers are marked in following
ways:
When recording from a CD or MD with the INPUT
switch set at a digital position (OPT or COAX) and
the source connected through the digital input
(DIGITAL OPTICAL IN or DIGITAL COAXIAL IN)
connector:
The deck automatically marks track numbers in the
same sequence as the original. If, however, a track is
repeated two or more times (e.g. by single-track
repeat play) or two or more tracks with the same
track number (e.g. from different MDs or CDs) are
played, the track or tracks are recorded as part of a
single, continuous track with a single track number.
If the source is an MD, track numbers may not be
marked for tracks of less than 4 seconds.
When recording from some CD players and multi
disc players connected through one of the digital
input connectors with the INPUT switch set at the
respective digital position:
The deck may not automatically mark track
numbers. In these cases, mark the track numbers
after recording, using the deck’s Divide Function (see
“Dividing Recorded Tracks” on page 31).
When recording from a source connected through
the LINE (ANALOG) IN jacks with the INPUT
switch set at ANALOG or when recording from a
DAT or satellite broadcast connected through one of
the digital input connectors with the INPUT switch
set at the respective digital position and “T.Mark
Off” selected in Setup Menu 02:
The source will be recorded as a single track.
Even while recording an analog source or a DAT or
satellite broadcast, you can mark track numbers if
“T.Mark LSyn” is selected in Setup Menu 02 (see
“Marking Track Numbers While Recording” on
page 13).
Recording on MDs
10
EN
Useful Tips for Recording
Checking the remaining recordable time on
the MD
Press TIME.
When you press the TIME button repeatedly while
recording, the display alternates between the
recording time of the current track and the
remaining recordable time on the MD.
When you press the TIME button repeatedly while
the deck is stopped, the display alternates between
total disc playing time and remaining recordable
time on the MD (see page 19).
Monitoring the input signal (Input Monitor)
Before starting recording, you can monitor the selected
input signal through the deck’s output connectors.
1 Press § EJECT to remove the MD.
2 Set INPUT according to the input signal you want
to monitor.
When the INPUT switch is set at ANALOG
The analog signal input through the LINE
(ANALOG) IN jacks is output to the DIGITAL
OPTICAL OUT connector after A/D conversion,
and then to the LINE (ANALOG) OUT jacks and
the PHONES jack after D/A conversion.
When the INPUT switch is set at OPT or COAX
After passing through the sampling rate converter,
the digital signal input through the respective
digital input connector is output to the DIGITAL
OPTICAL OUT connector, and after D/A
conversion to the LINE (ANALOG) OUT jacks and
PHONES jack.
3 Press r REC.
If the INPUT switch is set at ANALOG, “AD-DA”
appears in the display.
If the INPUT switch is set at OPT or COAX,
“-DA” appears in the display.
If “Auto Cut” appears in the display
(Auto Cut)
There has been no sound input for about 30 seconds
during recording. The 30 seconds of silence are
replaced by a blank of about 3 seconds and the deck
changes to recording pause.
If the deck continues pausing for about 10 minutes
after the Auto Cut Function activated, recording stops
automatically.
Note that this function does not activate even if there
has been no sound input for about 30 seconds when
the deck started recording from the blank portion.
z You can turn off the Auto Cut Function
For details, see “To turn off the Smart Space Function
and Auto Cut Function” below. Note that when you
turn off the Auto Cut Function, the Smart Space
Function is turned off automatically.
If “Smart Space” appears in the display
(Smart Space)
There has been an extended silence of 4 to 30 seconds
in length during recording. The silence is replaced
with a blank of about 3 seconds and the deck continues
recording. Note that new track numbers may not be
marked for portions recorded while this function is
activated. Also, the Smart Space Function does not
activate even if there has been an extended silence of 4
to 30 seconds in length when the deck started
recording from the blank portion.
To turn off the Smart Space Function and Auto Cut
Function
1 While the deck is stopped, press MENU/NO twice
to display “Setup Menu”.
2 Turn AMS to select “Setup 05”, then press AMS.
3 Turn AMS to select “S.Space Off”, then press AMS.
4 Press MENU/NO.
To turn on the Smart Space Function and Auto Cut
Function again
1 Do Steps 1 and 2 in “To turn off the Smart Space
Function and Auto Cut Function” above.
2 Turn AMS to select “S.Space On”, then press AMS.
3 Press MENU/NO.
AMS ±
p
0)
r
·
§
EJECT
P
§ EJECT
AMS ±
MENU/NO INPUT
TIME
r REC·p
11
EN
Recording on MDs
Notes
When you turn off the Smart Space Function, the Auto Cut
Function is also turned off automatically.
The Smart Space Function and Auto Cut Function are
factory set to on.
If you turn off the deck or disconnect the AC power cord,
the deck will recall the last setting (On or Off) of the Smart
Space and Auto Cut Functions the next time you turn on
the deck.
Playing back tracks just recorded
Do this procedure to immediately play back tracks that
have just been recorded.
Press · immediately after stopping recording.
Playback starts from the first track of the material just
recorded.
To play from the first track of the MD after
recording
1 Press p again after stopping recording.
2 Press ·.
Playback starts from the first track of the MD.
Recording Over Existing Tracks
Follow the procedure below to record over existing
material just as you would on an analog cassette tape.
1 Do Steps 1 to 5 in “Recording on an MD” on
page 6.
2 Turn AMS (or press = or +) until the
number of the track to be recorded over appears.
3 To record from the start of the track, continue
from Step 6 in “Recording on an MD” on page 7.
z While “Tr” flashes in the display
The deck is recording over an existing track, and stops
flashing when it reaches the end of the recorded
portion.
z To record from the middle of the track
1 After Step 2 above, press · to start playback.
2 Press P where you want to start recording.
3 Continue from Step 6 in “Recording on an MD” on
page 7.
Note
You cannot record from the middle of an existing track when
the “PROGRAM” or “SHUFFLE” is on.
AMS
±
p
0)
r
·
§
EJECT
P
AMS ±
NUMCHAR
WRITE CLEAR
NAME
+
STANDBY
=
START
P
STOP
T.REC MUSIC SYNC
0
=
·
)
+ r
P p
CD-SYNC
CD PLAYER FADER
LEVEL
=/+
Recording on MDs
12
EN
4 While monitoring the sound, turn AMS (or press
LEVEL +/– repeatedly) to adjust the recording
level so that the peak level meters reach their
highest point without turning on the OVER
indication. Occasional lighting of “OVER” is
acceptable.
The volume can only be increased up to +12.0 dB.
Therefore, if the digital signal level of the program
source is low, it may not be possible to set the
recording level to maximum.
5 Stop playing the program source.
6 To start recording, do the procedure starting from
Step 8 in “Recording on an MD” on page 7.
z You can use Setup Menu 11 or 12 to adjust the
digital recording level
1 While recording or in recording pause, press MENU/
NO twice to display “Setup Menu”.
2 Turn AMS to select “Setup 11”or “Setup 12”, then
press AMS. The dB display flashes.
Select “Setup 11” with the INPUT switch set at OPT
and “Setup 12” with the INPUT switch set at COAX.
3 Turn AMS to adjust the recording level, then press
AMS. The dB display changes from flashing to
lighted steadily.
4 Press MENU/NO.
z The Peak Hold Function freezes the level meter
display at the highest level reached by the input
signal
1 While the deck is stopped, press MENU/NO twice to
display “Setup Menu”.
2 Turn AMS to select “Setup 06”, then press AMS.
3 Turn AMS to select “P.Hold On”, then press AMS.
4 Press MENU/NO.
To turn off the Peak Hold Function, select “P.Hold Off”
in Step 3 above.
Adjusting the Recording Level
You can adjust the recording level before starting
recording.
Adjusting the digital recording level
1
Do Steps 1 to 6 in “Recording on an MD” on
pages 6 and 7.
Set INPUT to OPT or COAX in Step 4.
2 Play the portion of the program source with the
strongest signal level.
3 Press LEVEL/DISPLAY/CHAR (or DISPLAY)
repeatedly until the recording level adjustment
display appears.
OVER indication
AMS ±
p
0)
r
·
§
EJECT
P
AMS ±
LEVEL/DISPLAY/CHAR
3
6
H
8
M
13
R
18
W
23
C
PROGRAM
EJECT
TIME
NUM
!
A˜B
2
G
7
L
12
Q
17
V
22
B
SHUFFLE
PLAY MODE
SCROLL
CHAR
?
REPEAT
WRITE CLEAR
1
F
6
K
11
P
16
U
21
Z
A
CONTINUE
DISPLAY
NAME
/
>
25
MENU/NO
4
I
9
N
14
S
19
X
24
.
D
(
A.SPACE
+
STANDBY
=
START
P
STOP
T.REC MUSIC SYNC
5
J
10
O
15
T
20
Y
25
,
E
)
M.SCAN
YES
0
=
·
)
+ r
P p
CD-SYNC
CD PLAYER FADER
LEVEL
LEVEL +/–
DISPLAY
13
EN
Recording on MDs
Adjusting the analog recording level
1 Do Steps 1 to 6 in “Recording on an MD” on
pages 6 and 7.
Set INPUT to ANALOG in Step 4.
2 Play the portion of the program source with the
strongest signal level.
3 Press LEVEL/DISPLAY/CHAR (or DISPLAY)
repeatedly until the recording level adjustment
display appears.
4 While monitoring the sound, turn AMS (or press
LEVEL +/– repeatedly) to adjust the recording
level.
The volume can only be increased up to +12.0 dB.
Therefore, if the output level of the connected
component is low, it may not be possible to set the
recording level to maximum.
5 Stop playing the program source.
6 To start recording, do the procedure starting from
Step 8 in “Recording on an MD” on page 7.
z You can use Setup Menu 10 to adjust the analog
recording level
1 While recording or in recording pause, press MENU/
NO twice to display “Setup Menu”.
2 Turn AMS to select “Setup 10”, then press AMS.
3 Turn AMS to adjust the recording level, then press
AMS.
4 Press MENU/NO.
Marking Track Numbers While
Recording (Track Marking)
You can mark track numbers either manually or
automatically. By marking track numbers at specific
points, you can quickly locate the points later using the
AMS Function, or use various Editing Functions.
Marking track numbers manually
(Manual Track Marking)
You can mark track numbers at any time while
recording on an MD.
Press r REC at the place you want to add a track mark
while recording.
Marking track numbers automatically
(Automatic Track Marking)
The deck adds track marks differently in the following
cases:
When recording from CDs or MDs with the INPUT
switch set at OPT or COAX:
The deck marks track numbers automatically.
However, the Automatic Track Marking Function
does not activate when recording from some CD
players and multi disc players.
In all other cases:
If “T.Mark LSyn” is selected in Setup Menu 02, the
deck marks a new track number whenever the signal
drops to the specified level or below for about
1.5 seconds or longer, then rises to a specified level.
(Continued)
AMS ±
p
0)
r
·
§
EJECT
P
AMS ±
MENU/NO
r REC
Recording on MDs
14
EN
Recorded
portion
Beginning of the program
source to be recorded
When you press
AMS in Step 3
End of the program
source to be recorded
Time
To select “T.Mark Off” or “T.Mark LSyn” in Setup
Menu 02, do the procedure below:
1 While the deck is stopped, press MENU/NO
twice to display “Setup Menu”.
2 Turn AMS to select “Setup 02”, then press AMS.
3 Turn AMS to select “T.Mark Off” or “T.Mark
LSyn”, then press AMS.
“L.SYNC” lights up when you select “T.Mark
LSyn”.
4 Press MENU/NO.
z You can set the reference level that must pass
before a rise marks a new track number
In Automatic Track Marking, the input signal must
remain at or below a given reference level for
1.5 seconds or longer before a rise above the reference
level will mark a new track number.
Do the following procedure to specify the reference
level. Note that “T.Mark LSyn” should be selected in
Setup Menu 02.
1 While the deck is stopped, press MENU/NO twice to
display “Setup Menu”.
2 Turn AMS to select “Setup 03”, then press AMS.
3 Turn AMS to set the reference level.
You can set the reference level at –72 dB to 0 dB in
2 dB steps.
4 After selecting the reference level, press AMS.
5 Press MENU/NO.
Note
If you turn off the deck or disconnect the AC power cord, the
deck will recall the last settings of the Automatic Track
Marking Function (“T.Mark LSyn” or “T.Mark Off”) the next
time you turn on the deck.
Starting Recording With
6 Seconds of Prestored Audio
Data (Time Machine Recording)
When recording from an FM or satellite broadcast, the
first few seconds of material are often lost due to the
time it takes you to ascertain the contents and press the
record button. To prevent the loss of this material, the
Time Machine Recording Function constantly stores
6 seconds of the most recent audio data in a buffer
memory so that when you begin recording the
program source using this function, the recording
actually begins with the 6 seconds of audio data stored
in the buffer memory in advance as shown in the
illustration below.
1 Do Steps 1 to 6 in “Recording on an MD” on
pages 6 and 7.
The deck changes to recording pause.
2 Start playing the program source you want to
record.
The most recent 6 seconds of audio data is stored
in the buffer memory.
3 Press AMS (or T.REC) to start Time Machine
Recording.
Recording of the program source starts with the
6 seconds of audio data stored in the buffer
memory.
Audio data in 6-second buffer memory
AMS
±
p
0)
r
·
§
EJECT
P
AMS ±
NUM
!
A˜B
CHAR
?
REPEAT
WRITE CLEAR
NAME
/
>
25
(
A.SPACE
+
STANDBY
=
START
P
STOP
T.REC MUSIC SYNC
)
M.SCAN
0
=
·
)
+ r
P p
CD-SYNC
CD PLAYER FADER
LEVEL
T.REC
15
EN
Recording on MDs
To stop Time Machine Recording
Press p.
Note
The deck starts storing audio data when the deck is in
recording pause and you start playing the program source.
With less than 6 seconds of playing of the program source
and audio data stored in the buffer memory, Time Machine
Recording starts with less than 6 seconds of audio data.
Synchro-Recording With Audio
Equipment of Your Choice
(Music Synchro-Recording) Z
By using the MUSIC SYNC button on the remote, you
can automatically start recording in sync with the
signal input from the program source.
The method of marking track numbers differs,
depending on the program source being recorded and
the setting of the Setup Menu 02 (see “Notes on
Recording” on page 9).
1 Do Steps 1 to 5 in “Recording on an MD” on
page 6.
2 Press MUSIC SYNC.
The deck changes to recording pause.
3 Start playing the program source you want to
record.
The deck starts recording automatically.
To stop Music Synchro-Recording
Press p.
Note
When Music Synchro-Recording, the Smart Space Function
and the Auto Cut Function turn on automatically regardless
of their setting (On or Off) and type of input (digital or
analog).
3
6
H
8
M
13
R
18
W
23
C
PROGRAM
EJECT
TIME
NUM
!
A˜B
2
G
7
L
12
Q
17
V
22
B
SHUFFLE
PLAY MODE
SCROLL
CHAR
?
REPEAT
WRITE CLEAR
1
F
6
K
11
P
16
U
21
Z
A
CONTINUE
DISPLAY
NAME
/
>
25
MENU/NO
4
I
9
N
14
S
19
X
24
.
D
(
A.SPACE
STANDBYSTARTSTOP
T.REC MUSIC SYNC
5
J
10
O
15
T
20
Y
25
,
E
)
M.SCAN
YES
0
=
·
)
+ r
P p
CD-SYNC
MUSIC SYNC
Recording on MDs
16
EN
Synchro-Recording With a Sony
CD Player Z
By connecting your deck to a Sony CD player or Hi-Fi
Component System, you can easily dub CDs onto MDs
using the CD synchro buttons on the remote. If your
deck is connected to a Sony CD player by a digital
input cable, track numbers are automatically marked
as appear on the original even when “T.Mark Off” is
selected in Setup Menu 02. If your deck is connected to
a Sony CD player by audio connecting cords through
the LINE (ANALOG) IN jacks, track numbers are
automatically marked when you set Setup Menu 02 to
“T.Mark LSyn” (see page 13).
As the same remote controls both the CD player and
the deck, you may have trouble operating both units if
they are far from each other. If you do, place the CD
player close to this deck.
1 Set the source selector on the amplifier to CD.
2 Do Steps 2 to 5 in “Recording on an MD” on page
6 to prepare the deck for recording.
3 Insert a CD into the CD player.
4 Select the playback mode (Shuffle Play, Program
Play, etc.) on the CD player.
5 Press STANDBY.
The CD player pauses for playing and the deck
pauses for recording.
6 Press START.
The deck starts recording and the CD player starts
playback.
The track number and elapsed recording time of
the track appear in the display.
If the CD player does not start playing
Some CD player models may not respond when
you press START on the remote of the deck. Press
P on the remote of the CD player instead.
7 Press STOP to stop synchro-recording.
To pause recording
Press STANDBY or CD PLAYER P.
To restart recording, press START or CD PLAYER P.
A new track number is marked each time you pause
recording.
Notes
When the deck’s remote controls the CD player with a
mode selector, set the selector to CD1.
The deck may not automatically mark track numbers
when recording from some CD players and multi disc
players.
z You can use the remote of the CD player during
synchro-recording
When you press p, the CD player stops and the deck
pauses for recording.
When you press P, the CD player pauses and the deck
pauses for recording.
To restart synchro-recording, press ·.
z You can change CDs during synchro-recording
Do the following steps instead of Step 7 above.
1 Press p on the remote of the CD player.
The deck pauses for recording.
2 Change the CD.
3 Press · on the remote of the CD player.
Synchro-recording restarts.
z You can also do synchro-recording with a Sony video
CD player
Using the procedure for synchro-recording with a Sony
CD player, you can do synchro-recording with a Sony
video CD player also.
To select the video CD player, press button number 2
while pressing down the 1/u button on the remote
before starting the procedure.
To select the CD player again, press button number 1
while pressing down the 1/u button.
The deck is factory set to a CD player for synchro-
recording.
z You can check the remaining recordable time on the
MD
Press TIME (see page 19).
23
NUM
!
A˜B
22
CHAR
?
REPEAT
WRITE CLEAR
21
Z
NAME
/
>
25
24
.
(
A.SPACE
+
STANDBY
=
START
P
STOP
T.REC MUSIC SYNC
25
,
)
M.SCAN
0
=
·
)
+ r
P p
CD-SYNC
CD PLAYER FADER
LEVEL
START
CD PLAYER P
STANDBY
STOP
17
EN
Recording on MDs
Fading In and Out (Fader)
You can gradually increase the recording level at the
beginning of a recording (fade-in recording) or
gradually decrease the recording level at the end of a
recording (fade-out recording).
This function is convenient when, for example, you
don’t want the track cut off abruptly when the disc
reaches to its end.
Fade-in recording
During recording pause, press FADER at the position
where you want to start fade-in recording.
Z in “Fade Z 3.2s” flashes and the deck performs the
fade-in recording until the counter reaches “0.0s”.
Fade-out recording
During recording, press FADER at the position where
you want to start fade-out recording.
z in “Fade z 3.2s” flashes and the deck performs the
fade-out recording until the counter reaches “0.0s”.
The deck changes to recording pause when fade-out
recording finishes.
z You can set the duration of fade-in and fade-out
recording independently
1 While the deck is stopped, press MENU/NO twice to
display “Setup Menu”.
2 To set the duration of fade-in recording:
Turn AMS to select “Setup 08”, then press AMS.
To set the duration of fade-out recording:
Turn AMS to select “Setup 09”, then press AMS.
3 Turn AMS to set the duration.
Both the fade-in and fade-out recording durations can
be set in 0.1 second steps.
4 After selecting the duration, press AMS.
5 Press MENU/NO.
FADER
23
NUM
!
A˜B
22
CHAR
?
REPEAT
WRITE CLEAR
21
Z
NAME
/
>
25
24
.
(
A.SPACE
+
STANDBY
=
START
P
STOP
T.REC MUSIC SYNC
25
,
)
M.SCAN
0
=
·
)
+ r
P p
CD-SYNC
CD PLAYER FADER
LEVEL
FADER
Recording on MDs
18
EN
Recording on an MD Using a
Timer
By connecting a timer (not supplied) to the deck, you
can start and stop recording operations at specified
times. For further information on connecting the timer
and setting the starting and ending times, refer to the
instructions that came with the timer.
1 Do Steps 1 to 7 in “Recording on an MD” on
pages 6 and 7.
2 If you want to specify the time for the start of
recording, press p.
If you want to specify the time for the end of
recording, do Steps 8 and 9 in “Recording on an
MD” on page 7.
If you want to specify the time for both start and
end of recording, press p.
3 Set TIMER on the deck to REC.
4 Set the timer as required.
When you have set the time for the start of
recording, the deck turns off. When the
specified time arrives, the deck turns on and
starts recording.
When you have set the time for the end of
recording, recording continues. When the
specified time arrives, the deck stops recording
and turns off.
When you have set the time for both the start
and end of recording, the deck turns off. When
the starting time arrives, the deck turns on and
starts recording. When the ending time arrives,
the deck stops recording and turns off.
5 After you have finished using the timer, set
TIMER on the deck to OFF. Then place the deck
in standby status by plugging the AC power cord
of the deck into a wall outlet or set the timer to
continuous operation.
If TIMER is left at REC, the deck will
automatically start recording the next time you
turn the deck on.
If you do not change the deck to standby status
for more than a week after timer recording has
finished, the recorded contents may disappear.
Make sure to change the deck to standby status
within a week after timer recording is completed
The TOC on the MD is updated and recorded contents
are written to the MD when you turn the deck on. If
the recorded contents have disappeared, “Standby”
flashes when you turn the deck on.
Notes
It may take about 30 seconds after the deck is turned on
until recording starts. When recording at a specified time
using the timer, be sure to take this time into account
when setting the recording start time.
During timer recording, new material is recorded from the
end of the recorded portion on the MD.
Material recorded during timer recording will be saved to
the disc the next time you turn the deck on. “TOC
Writing” will flash in the display at that time. Do not
move the deck or pull out the AC power cord while “TOC
Writing” is flashing.
Timer recording will stop if the disc becomes full.
AMS ±
p
0)
r
·
§
EJECT
P
TIMER
p
.
Playing MDs
19
EN
Disc name
Music calendar
Total number
of tracks
Total disc
playing time
Total track number and total playing time
of all recorded tracks
Remaining recordable time of the disc
(Recorded MDs only)
Press
Press
The remaining recordable time of the disc
is not shown for premastered MDs.
Track number and playing time of the
current track
Track number and remaining time of the
current track
Remaining time of all recorded tracks
Press
Press
Press
AMS ±
p
0)
r
·
§
EJECT
P
TIME
LEVEL/DISPLAY/CHARSCROLL
3
6
H
8
M
C
PROGRAM
EJECT
TIME
2
G
7
L
B
SHUFFLE
PLAY MODE
SCROLL
1
F
6
K
A
CONTINUE
DISPLAY
MENU/NO
4
I
9
N
D
5
J
10
O
E
YES
TIME
SCROLL
DISPLAY
Playing MDs
A music calendar shows all the track numbers within a
grid if the MD is a premastered disc, or without a grid
if the MD is a recordable disc.
If the total track number exceeds 15, z appears to the
right of number 15 in the music calendar.
Note
When you insert a new MD or turn off the deck and turn it
on again, the last item displayed will reappear.
Checking the playing time, remaining time,
and track number
Each time you press TIME while playing an MD, you
can change the display as shown below. The track
numbers in the music calendar disappear after they are
played.
z The track name and disc name are displayed as
follows:
The disc name appears whenever the deck is stopped,
and the name of the current track appears when the
track is playing. If no title is recorded, “No Name”
appears instead of a title.
To label a recordable disc and its tracks, see “Labeling
Recordings” on page 33.
(Continued)
Using the Display
You can use the display to check disc and track
information such as the total track number, total
playing time of the tracks, remaining recordable time
of the disc and disc name.
Checking the total track number, total disc
playing time and remaining recordable
time of the disc
Each time you press TIME while the deck is stopped,
you can change the display as follows:
When you insert an MD, the disc name, total number
of tracks, total disc playing time, and the music
calender appear in the display as follows:
Playing MDs
20
EN
Locating a Specific Track
You can quickly locate any track while playing a disc
by using the AMS (Automatic Music Sensor) control,
= and + buttons, number buttons, or M.SCAN
button on the remote.
The next or succeeding
tracks
During playback, turn AMS clockwise
(or press + repeatedly) until you
find the track.
The current or
preceding tracks
During playback, turn AMS
counterclockwise (or press =
repeatedly) until you find the track.
A specific track
directly Z
Press number buttons to enter the
track number.
A specific track by
using AMS
1 Turn AMS until the track number
you want to locate appears while
the deck is stopped. (The track
number is flashing.)
2 Press AMS or ·.
By scanning each track
for 6 seconds (music
scan) Z
1 Press M.SCAN before you start
playing.
2 When you find the track you want,
press · to start playing.
z When you directly locate a track with a number over
25 Z
You must press >25 first, before entering the
corresponding digits.
Press >25 once if it is a 2-digit track number, and twice
if it is a 3-digit track number.
To enter “0”, press button 10.
Examples: • To play track number 30
Press >25 once, then 3 and 10.
• To play track number 100
Press >25 twice, then 1, 10 and 10.
To locate Do the following:
Output level (The recording level is displayed
while recording.)
Press
Press
Press
Press
Normal display
The contents of a program (only when
“PROGRAM” lights up)
Title (Disc name and track name)
Number
buttons
AMS
±
p
0)
r
·
§
EJECT
P
AMS ±
·
3
6
H
8
M
13
R
18
W
23
C
PROGRAM
EJECT
TIME
NUM
!
A˜B
2
G
7
L
12
Q
17
V
22
B
SHUFFLE
PLAY MODE
SCROLL
CHAR
?
REPEAT
WRITE CLEAR
1
F
6
K
11
P
16
U
21
Z
A
CONTINUE
DISPLAY
NAME
/
>
25
MENU/NO
4
I
9
N
14
S
19
X
24
.
D
(
A.SPACE
+
STANDBY
=
START
P
STOP
T.REC MUSIC SYNC
5
J
10
O
15
T
20
Y
25
,
E
)
M.SCAN
YES
0
=
·
)
+ r
P p
CD-SYNC
CD PLAYER FADER
LEVEL
M.SCAN
>25
·
=/+
z You can scroll a title of more than 12 characters
Press SCROLL.
Since the display shows up to 11 characters at a time,
press SCROLL to see the rest of the title if the title has
12 characters or more.
Press SCROLL again to pause scrolling, and again to
continue scrolling.
Changing the display
Each time you press LEVEL/DISPLAY/CHAR (or
DISPLAY) while the deck is stopped or playing, you
can change the display as follows:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136

Sony MDS-JE520 Инструкция по применению

Категория
Минидисковые плееры
Тип
Инструкция по применению

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ

на других языках