Sony MDS-JB920 Руководство пользователя

MiniDisc Deck

S

MiniDisc Deck

 1998 by Sony Corporation

3-864-150-51(1)

Operating Instructions

Instrukcja obsługi

Инструкция по эксплуатации

PL

EN

MDS-JB920

RF

P

2

EN

WARNING

To prevent fire or shock

hazard, do not expose the unit

to rain or moisture.

To avoid electrical shock, do

not open the cabinet. Refer

servicing to qualified

personnel only.

The laser component in this product

is capable of emitting radiation

exceeding the limit for Class 1.

This appliance is classified as a CLASS 1

LASER product. The CLASS 1 LASER

PRODUCT MARKING is located on the

rear exterior.

The following caution label is located

inside of the unit.

IN NO EVENT SHALL SELLER BE

LIABLE FOR ANY DIRECT,

INCIDENTAL OR

CONSEQUENTIAL DAMAGES OF

ANY NATURE, OR LOSSES OR

EXPENSES RESULTING FROM

ANY DEFECTIVE PRODUCT OR

THE USE OF ANY PRODUCT.

Precautions

On safety

Should any solid object or liquid fall

into the cabinet, unplug the deck and

have it checked by qualified personnel

before operating it any further.

On power sources

• Before operating the deck, check that

the operating voltage of the deck is

identical with your local power

supply. The operating voltage is

indicated on the nameplate at the rear

of the deck.

• The unit is not disconnected from the

AC power source (mains) as long as it

is connected to the wall outlet, even if

the unit itself has been turned off.

• If you are not going to use the deck

for a long time, be sure to disconnect

the deck from the wall outlet. To

disconnect the AC power cord, grasp

the plug itself; never pull the cord.

• AC power cord must be changed only

at the qualified service shop.

On operation

If the deck is brought directly from a

cold to a warm location, or is placed in a

very damp room, moisture may

condense on the lenses inside the deck.

Should this occur, the deck may not

operate properly. In this case, remove

the MD and leave the deck turned on

for about an hour until the moisture

evaporates.

On the MiniDisc cartridge

• Do not open the shutter to expose the

MD.

• Do not place the cartridge where it

will be subject to extremes of

sunlight, temperature, moisture or

dust.

On cleaning

Clean the cabinet, panel and controls

with a soft cloth slightly moistened with

a mild detergent solution. Do not use

any type of abrasive pad, scouring

powder or solvent such as alcohol or

benzine.

If you have any questions or problems

concerning your deck, please consult

your nearest Sony dealer.

Welcome!

Thank you for purchasing the Sony

MiniDisc Deck. Before operating the

deck, please read this manual

thoroughly and retain it for future

reference.

About This Manual

Conventions

• Controls in the instructions are those

on the deck; these may, however, be

substituted by controls on the remote

that are similarly named or, when

different, appear in the instructions

within brackets.

• The following icons are used in this

manual:

Z

Indicates a procedure that

requires use of the remote.

z

Indicates tips for making the

task easier and hints.

EN

3

EN

F

ES

P

Controlling a Separately Available Sony

CD Changer

Hooking Up the System ............................................ 34

Controlling a CD Changer from the MD Deck

(Mega CD Control Function) ................................. 35

Controlling a CD Changer from the MD Deck to

Make a Synchro Recording .................................... 37

Editing Recorded MDs

Notes on Editing........................................................ 39

Erasing Recordings (Erase Function) ........................ 39

Erasing a Part of a Track (A-B Erase Function)......... 41

Dividing Recorded Tracks (Divide Function) ........... 42

Combining Recorded Tracks (Combine Function) ... 43

Moving Recorded Tracks (Move Function) .............. 44

Labeling Recordings (Title Function)........................ 45

Undoing the Last Edit (Undo Function) ................... 49

Additional Information

Display Messages ...................................................... 50

System Limitations .................................................... 50

Troubleshooting ........................................................ 51

Specifications ............................................................. 52

Guide to the Serial Copy Management System ........ 53

Index .......................................................................... 54

Table of Setup Menus ................................................ 56

Self-Diagnosis Function............................................. 57

TABLE OF CONTENTS

Getting Started

Unpacking ........................................................................... 4

Hooking Up the System ....................................................4

About the CONTROL A1 Control System.....................6

Basic Functions of the CONTROL A1

Control System ............................................................... 7

Setting the Clock ................................................................7

Recording on an MD ............................................ 9

Playing an MD ...................................................... 11

Recording on MDs

Notes on Recording ................................................... 12

Useful Tips for Recording ......................................... 13

Adjusting the Recording Level.................................. 15

Marking Track Numbers While Recording

(Track Marking) ..................................................... 16

Starting Recording With 6 Seconds of Prestored

Audio Data (Time Machine Recording)................. 17

Synchro-Recording With Audio Equipment of Your

Choice(Music Synchro-Recording) ........................ 18

Synchro-Recording With a Sony CD Player.............. 18

Fading In and Out (Fader)......................................... 20

Recording the Current CD Track

(REC-IT Function) .................................................. 21

Recording on an MD Using a Timer ......................... 22

Playing MDs

Using the Display ...................................................... 23

Locating a Specific Track........................................... 25

Locating a Particular Point in a Track ....................... 26

Playing Tracks Repeatedly ........................................ 26

Playing in Random Order (Shuffle Play) .................. 27

Creating Your Own Program (Program Play) .......... 28

Useful Tips When Recording From MDs to Tape ..... 29

Fading In and Out (Fader)......................................... 30

Playing an MD Using a Timer................................... 31

Falling Asleep to Music ............................................. 32

Changing the Pitch (Pitch Control Function)............ 32

Setting the MD Deck Output..................................... 33

Getting Started

4

EN

çç

ç: Signal flow

What cords will I need?

• Audio connecting cords (supplied) (2)

• Optical cables (only one supplied) (3)

• Coaxial digital connecting cables (not supplied) (2)

Getting Started

Hooking Up the System

Overview

This section describes how to hook up the MD deck to

an amplifier or other components such as a CD player

or DAT deck. Be sure to turn off the power of each

component before connection.

to a wall outlet

(or to a timer

during timer

recording or

playback)

White

(L)

Red

(R)

White

(L)

Red

(R)

Amplifier

CD player, DAT deck,

or MD deck, etc.

Unpacking

Check that you received the following items:

• Audio connecting cords (2)

• Optical cable (1)

• Remote commander (remote) RM-D17M (1)

• R6 (size-AA) batteries (2)

Inserting batteries into the remote

You can control the deck using the supplied remote.

Insert two R6 (size-AA) batteries by matching the +

and – on the batteries. When using the remote, point it

at the remote sensor g on the deck.

z When to replace batteries

With normal use, the batteries should last for about six

months. When the remote no longer operates the deck,

replace all the batteries with new ones.

Notes

• Do not leave the remote near an extremely hot or humid

place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.

• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from

battery leakage and corrosion.

S-LINK

CONTROL A1

L

R

LINE

OUTIN

DIGITAL

OUTIN2 IN1

OPTICAL

IN

COAXIAL OPTICALCOAXIAL

OUT

(ANALOG)

DIGITAL

OPTICAL OUT

DIGITAL

OPTICAL IN

/

ç

REC

OUT

TAPE/MD

IN

ç

DIGITAL

COAXIAL IN

DIGITAL

COAXIAL OUT

CD player or

DAT deck, etc.

5

EN

Getting Started

Hookups

Connecting the deck to an amplifier

Connect the amplifier to the LINE (ANALOG) IN/

OUT jacks using the audio connecting cords (supplied),

making sure to match the color-coded cords to the

appropriate jacks on the components: red (right) to red

and white (left) to white. Be sure to make connections

firmly to prevent hum and noise.

çç

ç: Signal flow

Connecting the deck to a digital component such as

a CD player, DAT deck, digital amplifier, or another

MD deck

Connect the component through the DIGITAL

OPTICAL IN/OUT or DIGITAL COAXIAL IN/OUT

connectors with two (or three) optical cables (only one

supplied) and/or two coaxial digital connecting cables

(not supplied).

When using the optical cables

Take the caps off the connectors and then insert the plugs

parallelly until they click into place.

Be sure not to bend or tie together the optical cables.

You can connect the optical cable

to either OPTICAL IN1 or IN2

çç

ç: Signal flow

MD deck

Amplifier

When using the coaxial digital connecting cable

çç

ç: Signal flow

z If “Din Unlock” and “C71” appear in the display

Make sure the optical cable or the coaxial digital

connecting cable is connected properly.

z Automatic conversion of digital sampling rates

during recording

A built-in sampling rate converter automatically

converts the sampling frequency of various digital

sources to the 44.1 kHz sampling rate of your MD deck.

This allows you to record sources such as 32- and

48-kHz DAT or satellite broadcasts, as well as compact

discs and other MDs.

Note

If “Din Unlock” alternates with “C71”, or “Cannot Copy”

appears in the display, recording through the digital

connector is not possible. In this case, record the program

source through the LINE (ANALOG) IN jacks with the

INPUT switch set at ANALOG.

Connecting the AC power cord

Connect the AC power cord to a wall outlet or to the

outlet of a timer.

MD deck Digital component

MD deck

Digital component

DIGITAL

OUTIN2 IN1

OPTICAL

IN

COAXIAL

OPTICAL

COAXIAL

OUT

Ç

DIGITAL

OUTIN

COAXIAL

ç

Ç

L

R

L

R

LINE

(ANALOG)

OUTIN

TAPE / MD

INOUT

DIGITAL

OUTIN

OPTICAL

DIGITAL

OUTIN2 IN1

OPTICAL

IN

COAXIAL

OPTICAL

COAXIAL

OUT

ç

Ç

Getting Started

6

EN

About the CONTROL A1 Control

System

This MD deck is compatible with the CONTROL A1

Control System.

The CONTROL A1 Control System was designed to

simplify the operation of audio systems composed of

separate Sony components. CONTROL A1

connections provide a path for the transmission of

control signals which enable automatic operation and

control features usually associated with integrated

systems.

Currently, CONTROL A1 connections between a Sony

MD deck, CD player, amplifier (receiver), and cassette

deck provide automatic function selection and

synchronized recording.

In the future the CONTROL A1 connection will work

as a multifunction bus allowing you to control various

functions for each component.

Note

The CONTROL A1 Control System is designed to maintain

upward compatibility as the Control System is upgraded to

handle new functions. In this case, however, older

components will not be compatible with the new functions.

Compatibility with the former CONTROL A System

Although the CDP-CX153 is equipped with a

CONTROL

A terminal, it can be connected to

CONTROL

A1 components using a special

connecting cable*.

The CDP-CX151 however, cannot be connected to

CONTROL

A1.

* Use the Sony RK-G139HG (1 meter) monaural mini-

plug ˜ stereo mini-plug connecting cable or a similar

cable (less than 2 meters long with no resistance).

Be sure to connect the STEREO mini-plug to the

CONTROL

A component and the MONO mini-plug

to the CONTROL

A1 component.

STEREO

To CDP-CX153

(CONTROL A)

To the CONTROL

A1 component

MONO

Connecting the CONTROL A1 Control

System

• Connect the CONTROL A1 cables in series to the

CONTROL A1 jacks on the back of each component.

Be sure to connect a CONTROL A1 compatible

amplifier (receiver) to take advantage of the

automatic function selection feature.

• The components can be connected in any order.

• You can connect up to ten CONTROL A1 compatible

components.

• The CONTROL A1 functions will work when the

component you want to operate is turned on, even if

all of the connected components are not turned on.

• As a rule, the CONTROL A1 remote control system

should not incorporate more than one of each type of

component (i.e., 1 MD deck, 1 CD player, 1 tape deck

and 1 receiver). You may, however, be able to

connect more than one of certain CD players. Refer

to the operating instructions supplied with the

respective component for details.

About the CONTROL A1 cable

• Use a commercially available 2P (mono) mini-plug cable

less than 2 meters long, with a maximum outer diameter

no greater than 11 mm, and no resistance. Some

CONTROL A1 compatible components are supplied with

a CONTROL A1 cable as an accessory.

• If a component has more than one CONTROL A1 jack, you

can use either one, or connect a different component to

each jack.

“S-LINK” is a general name for Sony’s Bus System, and

includes the CONTROL A1 Control System.

Amplifier

(receiver)

MD

deck

CD

player

Tape

deck

Other

component

S-LINK

CONTROL A1

S-LINK

CONTROL A1

7

EN

Getting Started

Basic Functions of the

CONTROL A1 Control System

Automatic function selection

When you connect CONTROL A1 compatible Sony

components using CONTROL A1 cables, the function

selector on the amplifier (or receiver) automatically

switches to the correct input when you press the play

button on one of the connected components.

(If you press · (play button) on the MD deck while

the CD is playing, the function selector on the amplifier

switches from CD to MD.)

Notes

• This function only works when the components are

connected to the amplifier (or receiver) inputs according

to the names on the function buttons. Certain receivers

allow you to switch the names of the function buttons. In

this case, refer to the operating instructions supplied with

the receiver.

• When recording, do not play any components other than

the recording source. It will cause the automatic function

selection to operate.

Synchronized recording

This function lets you conduct synchronized recording

between the MD deck and selected source component.

1 Set the source selector on the amplifier (or

receiver) to the source component.

2 Set the source component to pause mode (make

sure both the · and P indicators light together).

3 Set the deck to recording pause mode.

4 Press P on the deck.

The source component is released from the pause

mode, and recording begins shortly thereafter.

When playback ends from the source component,

recording stops.

Notes

• Do not set more than one component to the pause mode.

• This MD deck is equipped with a special synchronized

recording function that uses the CONTROL A1 Control

System (see “Making a synchro recording from a CD

player connected with a control A1 cable” on page 19).

You can also make a synchro recording using the Mega

CD Control Function via the CONTROL A1 Control

System (see “Controlling a CD Changer from the MD

Deck to Make a Synchro Recording” on page 37).

Setting the Clock

Once you set the MD deck’s internal clock, the MD

deck will automatically record the date and time of all

recordings. When playing a track, you can display the

date and time the track was recorded (see page 24).

Time on this deck is displayed on a 24-hour clock.

1 With the deck in standby status (the STANDBY

indicator lights red), press SCROLL/CLOCK SET

down for about 2 seconds until the day indication

in the display starts flashing.

2 Turn AMS to enter the current day, then press

AMS.

The day indication stops flashing, and the month

indication starts flashing.

(Continued)

Pp

0

)

r

§

·

SCROLL/CLOCK SET

STANDBY ≠ AMS ±

3

6

H

8

M

13

R

18

W

C

PROGRAM

EJECT

TIME D.O BIT

2

G

7

L

12

Q

17

V

B

SHUFFLE PRESENTRECORDED

PLAY MODE

SCROLL

1

F

6

K

11

P

16

U

A

CONTINUE

DISPLAY

MENU/NO

4

I

9

N

14

S

19

X

D

5

J

10

O

15

T

20

Y

E

YES

DATE

PRESENT

Getting Started

8

EN

3 Repeat Step 2 to enter the month, year, hour, and

minute.

z For precise time and date stamping of recordings

Reset the time at least once a week.

Note

If the AC power cord is disconnected for a long time, the

memorized clock settings will disappear and “Standby” will

flash in the display the next time you plug in and turn on the

deck. If this happens, reset the clock.

Displaying the current date and time Z

You can display the current date and time any time

even when the deck is in standby status.

Press DATE PRESENT.

Each press of the button changes the display as

follows:

n Current display n Date n Time

z You can display the current date and time with an

on-deck button

Press the SCROLL/CLOCK SET button. Each press of

the button changes the display in the same order as the

DATE PRESENT button on the remote does.

Changing the date and/or time

1

With the deck in standby status (the STANDBY

indicator lights red), press SCROLL/CLOCK SET

down for about 2 seconds until the day indication

in the display starts flashing.

2 Press SCROLL/CLOCK SET or AMS repeatedly

until the item you want to change flashes.

3 Turn AMS to change the contents of the selected

item.

4 To complete the setting, press AMS repeatedly

until all items stop flashing.

Deactivating the demonstration mode

If the MD deck does not contain a disc, demonstration

mode is activated automatically after about ten

minutes.

To deactivate the demonstration mode, press any

button on the MD deck or the remote.

Basic Operations

9

EN

Recording on an MD

Monitor audio during recording

Even if you set REC MODE to

MONO, the monitor signal does

not become monaural.

≠ ±

REC

INPUT

MONO

PHONES

PHONE LEVEL

PLAY MODE

SCROLL/

CLOCK SET

AMS

YES

MENU/

NO

TIMER

REC OFF PLAY

DISPLAY/

CHAR

REC MODE

EJECT

REC LEVEL

DIGITAL ANALOG

Pp

0

)

§

0

10

·

•

OPT1

STANDBY

TIMEREPEAT

STEREO

MUSIC

SYNC

FADER

MEGA

CONTROL

CLEAR

OPT2

COAX

ANALOG

DIGITAL

PUSH ENTER

1

2

3

–

+

4

5

6

7

8

9

10

0

2

3

5 4

86

7

r

Basic Operations

With the label side up

With the arrow pointing this way

1

Turn on the amplifier and play the program source you want

to record.

2

Press 1/u.

The STANDBY indicator turns off.

3

Insert a recordable MD.

If the MD has a recorded material on it, the deck will

automatically start recording from the end of the last recorded

track.

4

Set INPUT to the corresponding input connector.

To record through Set INPUT to

DIGITAL OPTICAL IN1 OPT1

DIGITAL OPTICAL IN2 OPT2

DIGITAL COAXIAL IN COAX

LINE (ANALOG) IN ANALOG

5

Set REC MODE to the mode you want to record in.

To record in Set REC MODE*

1

to

Stereo sound STEREO

Monaural sound*

2

MONO

*

1

If you switch REC MODE during recording or recording pause, recording

stops.

*

2

In the monaural recording, you can record about two times longer than in

the stereo recording.

(Continued)

Basic Operations

10

EN

6

Press r REC.

The deck becomes ready to record.

7

Adjust the recording level.

When recording through the DIGITAL COAXIAL IN, OPTICAL IN1, or

IN2 connector

Adjust the outer REC LEVEL (DIGITAL) control so that the

peak level meter in the display is a maximum of 0 dB. For

details, see page 15.

When recording through the LINE (ANALOG) IN jacks

Setting the inner REC LEVEL (ANALOG) control at 4 is

satisfactory for most purposes. For details, see page 15.

8

Press · or P.

Recording starts.

9

Start playing the program source.

Do not disconnect the deck from the power source immediately after

recording

If you do, recorded material may not be saved to the MD. To save the

material, after recording, press § EJECT to take out the MD or change the

deck to standby by pressing 1 /u . “TOC Writing” will flash in the display at

this time.

After “TOC Writing” stops flashing and goes out, you can pull out the AC

power cord.

To Press

Stop recording p

Pause recording* P. Press the button again or press · to resume

recording.

Take out the MD § EJECT after stopping

* Whenever you pause recording, the track number increases by one. For example, if

you paused recording while recording on track 4, the track number increases by

one and recording continues on the new track when restarted.

To protect an MD against accidental erasure

To make it impossible to record on an MD, slide the tab in the direction of

arrow, opening the slot. To allow recording, close the slot.

When “TOC Writing” flashes in

the display

The deck is currently updating the

Table Of Contents (TOC). Do not

move the deck or pull out the AC

power cord. Changes to an MD

made through recording are saved

only when you update the TOC by

ejecting the MD or changing the

deck to standby by pressing the

1/u switch.

Rear of the disc

Record-protect tab

Slide the tab in the

direction of arrow

Basic Operations

11

EN

Playing an MD

3

4

≠ ±

REC

INPUT

MONO

PHONES

PHONE LEVEL

PLAY MODE

SCROLL/

CLOCK SET

AMS

YES

MENU/

NO

TIMER

REC OFF PLAY

DISPLAY/

CHAR

REC MODE

EJECT

REC LEVEL

DIGITAL ANALOG

p

0

)

§

0

10

·

•

OPT1

STANDBY

TIMEREPEAT

STEREO

MUSIC

SYNC

FADER

MEGA

CONTROL

CLEAR

OPT2

COAX

ANALOG

DIGITAL

PUSH ENTER

1

2

3

–

+

4

5

6

7

8

9

10

0

P

r

2

z You can locate and play back

a track while the deck is

stopped

1 Turn AMS (or press = or

+) until the number of the

track you want to play

appears.

2 Press AMS or ·.

z To use headphones

Connect them to PHONES jack.

Use PHONE LEVEL to adjust

the volume.

z You can change the MD

playback speed

See “Changing the Pitch” on

page 32.

With the label side upWith the arrow pointing this way

1

Turn on the amplifier and set the source selector to the position

for MD deck.

2

Press 1/u.

The STANDBY indicator turns off.

3

Insert an MD.

4

Press ·.

The deck starts playing. Adjust the volume on the amplifier.

To Do the following:

Stop playing Press p.

Pause playing Press P. Press the button again or press

· to

resume playing.

Go to the next track Turn AMS clockwise (or press + on the

remote).

Go to the current track Turn AMS counterclockwise (or press = on the

or the preceding track remote).

Take out the MD Press § EJECT after stopping playing.

Recording on MDs

12

EN

Recording on MDs

• When recording from DAT or satellite broadcasts

with the INPUT switch set at the respective digital

position, the deck automatically marks a track

number whenever the sampling frequency of the

input signal changes regardless of the Setup Menu 02

setting.

z You can mark track numbers during or after

recording

For details, see “Marking Track Numbers While

Recording” (page 16) and “Dividing Recorded Tracks”

(page 42).

When “TOC Writing” flashes in the display

The deck is currently updating the Table Of Contents

(TOC). Do not move the deck or pull out the AC

power cord. Changes to an MD made through

recording are saved only when you update the TOC by

ejecting the MD or changing the deck to standby by

pressing the 1/u switch.

The MD deck uses the SCMS (Serial Copy

Management System on page 53)

MDs recorded through digital input connector cannot

be copied onto other MDs or DAT tapes through the

digital output connector.

When the deck is recording or in recording pause,

digital signals input through one of the digital input

connectors are output to the respective digital

output connector with the same sampling rate

To change the digital input signal to another sampling

rate for output (without recording it to an MD), use

Input Monitor Function (see page 13).

Notes on Recording

If “Protected” alternates with “C11” in the display

The MD is record-protected. Close the slot to record

on the disc (see “To protect an MD against accidental

erasure” on page 10).

If “Din Unlock” alternates with “C71” in the display

• The digital program source is not connected as you

set with the INPUT switch in Step 4 on page 9.

To continue, connect the program source properly.

• The program source is not on.

Turn on the program source.

Depending on the menu settings and source being

recorded, track numbers are marked in following

ways:

• When recording from a CD or MD with the INPUT

switch set at a digital position (OPT1, OPT2 or

COAX) and the source connected through the digital

input (DIGITAL OPTICAL IN1, IN2 or DIGITAL

COAXIAL IN) connector:

The deck automatically marks track numbers in the

same sequence as the original. If, however, a track is

repeated two or more times (e.g. by single-track

repeat play) or two or more tracks with the same

track number (e.g. from different MDs or CDs) are

played, the track or tracks are recorded as part of a

single, continuous track with a single track number.

If the source is an MD, track numbers may not be

marked for tracks of less than 4 seconds.

• When recording from some CD players and multi

disc players connected through one of the digital

input connectors with the INPUT switch set at the

respective digital position:

The deck may not automatically mark track

numbers. In these cases, mark the track numbers

after recording, using the deck’s Divide Function (see

“Dividing Recorded Tracks” on page 42).

• When recording from a source connected through

the LINE (ANALOG) IN jacks with the INPUT

switch set at ANALOG or when recording from a

DAT or satellite broadcast connected through one of

the digital input connectors with the INPUT switch

set at the respective digital position and “T.Mark

Off” selected in Setup Menu 02:

The source will be recorded as a single track.

• Even while recording an analog source or a DAT or

satellite broadcast, you can mark track numbers if

“T.Mark LSyn” is selected in Setup Menu 02 (see

“Marking Track Numbers While Recording” on

page 16).

13

EN

Recording on MDs

Useful Tips for Recording

Checking the remaining recordable time on

the MD

Press TIME.

• When you press the TIME button repeatedly while

the deck is stopped, the display alternates between

total disc playing time and remaining recordable

time on the MD (see page 23).

• When you press the TIME button repeatedly while

recording, the display alternates between the

recording time of the current track and the

remaining recordable time on the MD.

Changing the display while recording

Each time you press DISPLAY/CHAR (or DISPLAY)

while the deck is recording, you can change the display

as follows:

Monitoring the input signal (Input Monitor)

Before starting recording, you can monitor the selected

input signal through the deck’s output connectors.

1 Press § EJECT to remove the MD.

2 Set INPUT according to the input signal you want

to monitor.

When the INPUT switch is set at ANALOG

The analog signal input through the LINE

(ANALOG) IN jacks is output to the digital output

connector after A/D conversion, and then to the

LINE (ANALOG) OUT jacks and the PHONES

jack after D/A conversion.

When the INPUT switch is set at OPT1, OPT2 or

COAX

After passing through the sampling rate converter,

the digital signal input through the respective

digital input connector is output to the digital

output connector, and after D/A conversion to the

LINE (ANALOG) OUT jacks and PHONES jack.

3 Press r REC.

If the INPUT switch is set at ANALOG, “AD-DA”

appears in the display.

If the INPUT switch is set at OPT1, OPT2 or

COAX, “-DA” appears in the display.

If “Auto Cut” appears in the display

(Auto Cut)

There has been no sound input for about 30 seconds

during recording. The 30 seconds of silence are

replaced by a blank of about 3 seconds and the deck

changes to recording pause.

If the deck continues pausing for about 10 minutes

after the Auto Cut Function activated, recording stops

automatically.

Note that this function does not activate even if there

has been no sound input for about 30 seconds when

the deck started recording from the blank portion.

z You can turn off the Auto Cut Function

For details, see “To turn off the Smart Space Function

and Auto Cut Function” on page 14. Note that when

you turn off the Auto Cut Function, the Smart Space

Function is turned off automatically.

(Continued)

Press

Normal display

Recording level display

FS (sampling frequency) display

Pp

0

)

r

§

·

§ EJECT

≠ AMS ±

MENU/NO

INPUT

TIME r REC·

p

DISPLAY/CHAR

Recording on MDs

14

EN

If “Smart Space” appears in the display

(Smart Space)

There has been an extended silence of 4 to 30 seconds

in length during recording. The silence is replaced

with a blank of about 3 seconds and the deck continues

recording. Note that new track numbers may not be

marked for portions recorded while this function is

activated. Also, the Smart Space Function does not

activate even if there has been an extended silence of 4

to 30 seconds in length when the deck started

recording from the blank portion.

To turn off the Smart Space Function and Auto Cut

Function

1 While the deck is stopped, press MENU/NO twice

to display “Setup Menu”.

2 Turn AMS to select “Setup 05”, then press AMS.

3 Turn AMS to select “S.Space Off”, then press AMS.

4 Press MENU/NO.

To turn on the Smart Space Function and Auto Cut

Function again

1 Do Steps 1 and 2 in “To turn off the Smart Space

Function and Auto Cut Function” above.

2 Turn AMS to select “S.Space On”, then press AMS.

3 Press MENU/NO.

Notes

• When you turn off the Smart Space Function, the Auto Cut

Function is also turned off automatically.

• The Smart Space Function and Auto Cut Function are

factory set to on.

• If you turn off the deck or disconnect the AC power cord,

the deck will recall the last setting (On or Off) of the Smart

Space and Auto Cut Functions the next time you turn on

the deck.

Switching the bit length

You can improve the recording quality by switching

the bit length to match the CD player or DA converter

connected to the digital input connector.

1 While the deck is stopped, press MENU/NO

twice to display “Setup Menu”.

2 Turn AMS to select “Setup 12”, then press AMS.

3 Turn AMS to select the desired bit length, then

press AMS.

4 Press MENU/NO.

Notes

• This function operates only for the digital signal input

through the digital input connector.

• The bit length is normally set to 20 bits, but you can select

from 24, 20 or 16 bits.

• If you switch the bit length during recording, the sound

drops out momentarily.

Playing back tracks just recorded

Do this procedure to immediately play back tracks that

have just been recorded.

Press · immediately after stopping recording.

Playback starts from the first track of the material just

recorded.

To play from the first track of the MD after

recording

1 Press p again after stopping recording.

2 Press ·.

Playback starts from the first track of the MD.

Recording Over Existing Tracks

Follow the procedure below to record over existing

material just as you would on an analog cassette tape.

1 Do Steps 1 to 5 in “Recording on an MD” on

page 9.

2 Turn AMS (or press = or +) until the

number of the track to be recorded over appears.

3 To record from the start of the track, continue

from Step 6 in “Recording on an MD” on page 10.

z While “Tr” flashes in the display

The deck is recording over an existing track, and stops

flashing when it reaches the end of the recorded

portion.

z To record from the middle of the track

1 After Step 2 above, press · to start playback.

2 Press P where you want to start recording.

3 Continue from Step 6 in “Recording on an MD” on

page 10.

Note

You cannot record from the middle of an existing track when

the “PROGRAM” or “SHUFFLE” is on.

15

EN

Recording on MDs

4 Stop playing the program source.

5 To start recording, do the procedure starting from

Step 8 in “Recording on an MD” on page 10.

z The Peak Hold Function freezes the level meter

display at the highest level reached by the input

signal

To turn on the Peak Hold Function by Setup Menu 06

setting

1 While the deck is stopped, press MENU/NO twice to

display “Setup Menu”.

2 Turn AMS to select “Setup 06”, then press AMS.

3 Turn AMS to select “P.Hold On”, then press AMS.

4 Press MENU/NO.

To turn on the Peak Hold Function using the remote

Press P.HOLD to display “P.Hold On.”

To turn off the Peak Hold Function, select “P.Hold Off”

in Step 3 above. (Or press P.HOLD on the remote to

display “P.Hold Off”.)

Adjusting the analog recording level

1 Do Steps 1 to 6 in “Recording on an MD” on

pages 9 and 10.

2 Play the portion of the program source with the

strongest signal level.

3 While monitoring the sound, turn inner REC

LEVEL (ANALOG) to adjust the recording level.

If the output level of the connected component is

too low, it may not be possible to set the

recording level to maximum.

4 Stop playing the program source.

5 To start recording, do the procedure starting from

Step 8 in “Recording on an MD” on page 10.

Adjusting the Recording Level

You can adjust the recording level before starting

recording.

Adjusting the digital recording level

You do not normally need to adjust the digital

recording level. The level is adjusted mainly when the

level of the source is low.

1 Do Steps 1 to 6 in “Recording on an MD” on

pages 9 and 10.

2 Play the portion of the program source with the

strongest signal level.

3 While monitoring the sound, turn outer REC

LEVEL (DIGITAL) (or press DIGITAL REC

LEVEL/ANALOG OUT LEVEL +/–) to adjust the

recording level so that the peak level meters reach

their highest point without turning on the OVER

indication. Occasional lighting of “OVER” is

acceptable.

If the digital signal level of the source is too low,

it may not be possible to set the recording level to

maximum.

OVER indication

Pp

0

)

r

§

·

≠ AMS ±

MENU/NO

REC LEVEL

(DIGITAL/ANALOG)

DIGITAL REC LEVEL

/ANALOG OUT LEVEL

18

W

23

NUM

!

A˜B

17

V

22

–

CHAR

?

REPEAT

WRITE CLEAR

16

U

21

Z

NAME

/

>

25

19

X

24

.

(

P.HOLD

A.SPACE

+

STANDBY

=

START

P

STOP

T.REC MUSIC SYNC

REC-IT

20

Y

25

,

)

M.SCAN

0

=

·

)

+ r

P p

CD-SYNC

CD PLAYER FADER

P. HOLD

DIGITAL REC LEVEL

/ANALOG OUT LEVEL +/–

Recording on MDs

16

EN

Marking Track Numbers While

Recording (Track Marking)

You can mark track numbers either manually or

automatically. By marking track numbers at specific

points, you can quickly locate the points later using the

AMS Function, or use various Editing Functions.

Marking track numbers manually

(Manual Track Marking)

You can mark track numbers at any time while

recording on an MD.

Press r REC at the place you want to add a track mark

while recording.

Marking track numbers automatically

(Automatic Track Marking)

The deck adds track marks differently in the following

cases:

• When recording from CDs or MDs with the INPUT

switch set at OPT1, OPT2 or COAX:

The deck marks track numbers automatically.

However, the Automatic Track Marking Function

may not activate when recording from some CD

players and multi disc players.

• In all other cases:

If “T.Mark LSyn” is selected in Setup Menu 02, the

deck marks a new track number whenever the signal

drops to the specified level or below for about

1.5 seconds or longer, then rises to a specified level.

To select “T.Mark Off” or “T.Mark LSyn” in Setup

Menu 02, do the procedure below:

1 While the deck is stopped, press MENU/NO

twice to display “Setup Menu”.

2 Turn AMS to select “Setup 02”, then press AMS.

3 Turn AMS to select “T.Mark Off” or “T.Mark

LSyn”, then press AMS.

“L.SYNC” lights up when you select “T.Mark

LSyn”.

4 Press MENU/NO.

z You can set the reference level that must pass

before a rise marks a new track number

In Automatic Track Marking, the input signal must

remain at or below a given reference level for

1.5 seconds or longer before a rise above the reference

level will mark a new track number.

Do the following procedure to specify the reference

level. Note that “T.Mark LSyn” should be selected in

Setup Menu 02.

1 While the deck is stopped, press MENU/NO twice to

display “Setup Menu”.

2 Turn AMS to select “Setup 03”, then press AMS.

3 Turn AMS to set the reference level.

You can set the reference level at –72 dB to 0 dB in

2 dB steps.

4 After selecting the reference level, press AMS.

5 Press MENU/NO.

Note

If you turn off the deck or disconnect the AC power cord, the

deck will recall the last settings of the Automatic Track

Marking Function (“T.Mark LSyn” or “T.Mark Off”) the next

time you turn on the deck.

Pp

0

)

r

§

·

≠ AMS ±

MENU/NO

r REC

17

EN

Recording on MDs

Starting Recording With

6 Seconds of Prestored Audio

Data (Time Machine Recording)

When recording from an FM or satellite broadcast, the

first few seconds of material are often lost due to the

time it takes you to ascertain the contents and press the

record button. To prevent the loss of this material, the

Time Machine Recording Function constantly stores

6 seconds of the most recent audio data in a buffer

memory so that when you begin recording the

program source using this function, the recording

actually begins with the 6 seconds of audio data stored

in the buffer memory in advance as shown in the

illustration below.

1 Do Steps 1 to 6 in “Recording on an MD” on

pages 9 and 10.

The deck changes to recording pause.

2 Start playing the program source you want to

record.

The most recent 6 seconds of audio data is stored

in the buffer memory.

3 Press AMS (or T.REC) to start Time Machine

Recording.

Recording of the program source starts with the

6 seconds of audio data stored in the buffer

memory.

To stop Time Machine Recording

Press p.

Note

The deck starts storing audio data when the deck is in

recording pause and you start playing the program source.

With less than 6 seconds of playing of the program source

and audio data stored in the buffer memory, Time Machine

Recording starts with less than 6 seconds of audio data.

Beginning of the program

source to be recorded

When you press

AMS in Step 3

End of the program

source to be recorded

Recorded

portion

Time

Audio data in 6-second buffer memory

Pp

0

)

r

§

·

≠ AMS ±

NUM

!

A˜B

CHAR

?

REPEAT

WRITE CLEAR

NAME

/

>

25

(

P.HOLD

A.SPACE

+

STANDBY

=

START

P

STOP

T.REC MUSIC SYNC

REC-IT

)

M.SCAN

0

=

·

)

+ r

P p

CD-SYNC

CD PLAYER FADER

T.REC

DIGITAL REC LEVEL

/ANALOG OUT LEVEL

Recording on MDs

18

EN

Synchro-Recording With Audio

Equipment of Your Choice

(Music Synchro-Recording)

By using the MUSIC SYNC button, you can

automatically start recording in sync with the signal

input from the program source.

The method of marking track numbers differs,

depending on the program source being recorded and

the setting of the Setup Menu 02 (see “Notes on

Recording” on page 12).

1 Do Steps 1 to 5 in “Recording on an MD” on

page 9.

2 Press MUSIC SYNC.

The deck changes to recording pause.

3 Start playing the program source you want to

record.

The deck starts recording automatically.

To stop Music Synchro-Recording

Press p.

Note

When Music Synchro-Recording, the Smart Space Function

and the Auto Cut Function turn on automatically regardless

of their setting (On or Off) and type of input (digital or

analog).

Synchro-Recording With a Sony

CD Player Z

By connecting your deck to a Sony CD player or Hi-Fi

Component System, you can easily dub CDs onto MDs

using the CD synchro buttons on the remote. If your

deck is connected to a Sony CD player by a digital

input cable, track numbers are automatically marked

as appear on the original even when “T.Mark Off” is

selected in Setup Menu 02. If your deck is connected to

a Sony CD player by audio connecting cords through

the LINE (ANALOG) IN jacks, track numbers are

automatically marked when you set Setup Menu 02 to

“T.Mark LSyn” (see page 16).

As the same remote controls both the CD player and

the deck, you may have trouble operating both units if

they are far from each other. If you do, place the CD

player close to this deck.

1 Set the source selector on the amplifier to CD.

2 Do Steps 2 to 5 in “Recording on an MD” on page

9 to prepare the deck for recording.

3 Insert a CD into the CD player.

4 Select the playback mode (Shuffle Play, Program

Play, etc.) on the CD player.

5 Press STANDBY.

The CD player pauses for playing and the deck

pauses for recording.

MUSIC SYNC

NUM

!

A˜B

CHAR

?

REPEAT

WRITE CLEAR

NAME

/

>

25

(

P.HOLD

A.SPACE

+

STANDBY

=

START

P

STOP

T.REC MUSIC SYNC

REC-IT

)

M.SCAN

0

=

·

)

+ r

P p

CD-SYNC

CD PLAYER FADER

STANDBY

STOP

START

CD PLAYER P

DIGITAL REC LEVEL

/ANALOG OUT LEVEL

NUM

!

A˜B

CHAR

?

REPEAT

WRITE CLEAR

NAME

/

>

25

(

P.HOLD

A.SPACE

+

STANDBY

=

START

P

STOP

T.REC MUSIC SYNC

REC-IT

)

M.SCAN

0

=

·

)

+ r

P p

CD-SYNC

CD PLAYER FADER

MUSIC SYNC

DIGITAL REC LEVEL

/ANALOG OUT LEVEL

19

EN

Recording on MDs

6 Press START.

The deck starts recording and the CD player starts

playback.

The track number and elapsed recording time of

the track appear in the display.

If the CD player does not start playing

Some CD player models may not respond when

you press START on the remote of the deck. Press

P on the remote of the CD player instead.

7 Press STOP to stop synchro-recording.

To pause recording

Press STANDBY or CD PLAYER P.

To restart recording, press START or CD PLAYER P.

A new track number is marked each time you pause

recording.

Notes

• When the deck’s remote controls the CD player with a

mode selector, set the selector to CD1.

• The deck may not automatically mark track numbers

when recording from some CD players.

z You can use the remote of the CD player during

synchro-recording

When you press p, the CD player stops and the deck

pauses for recording.

When you press P, the CD player pauses and the deck

pauses for recording.

To restart synchro-recording, press ·.

z You can change CDs during synchro-recording

Do the following steps instead of Step 7 above.

1 Press p on the remote of the CD player.

The deck pauses for recording.

2 Change the CD.

3 Press · on the remote of the CD player.

Synchro-recording restarts.

z You can also do synchro-recording with a Sony video

CD player

Using the procedure for synchro-recording with a Sony

CD player, you can do synchro-recording with a Sony

video CD player also.

To select the video CD player, press button number 2

while pressing down the 1/u switch on the remote

before starting the procedure.

To select the CD player again, press button number 1

while pressing down the 1/u switch.

The deck is factory set to a CD player for synchro-

recording.

z You can check the remaining recordable time on the

MD

Press TIME (see page 23).

z During synchro-recording, the deck copies CD text

information (CD text and disc memos) as it is to the

MD (Disc Memo Copy Function)

The Disc Memo Copy function operates when you make

a synchro-recording from a Sony CD player connected

with a control A1 cable to the MD deck.

Notes

• The Disc Memo Copy Function may not operate for

extremely short CD tracks.

• Text information may not be copied for some CDs.

Making a synchro recording from a CD

player connected with a control A1 cable

You can make a synchro recording from a Sony CD

player with a CONTROL A1 jack connected with a

control A1 cable to the MD deck.

1 Turn on the amplifier and set the source selector

to CD.

2 Do Steps 2 to 5 of “Recording on an MD” on page

9.

3 Set the CD player to the play mode (e.g., Program

Play or Shuffle Play) you want to use to record to

the MD deck.

4 Set the CD player to playback pause mode.

(· and P both light up.)

5 Press r REC on the deck.

The MD deck stands by for recording.

6 Press P on the deck.

CD player pause is canceled and recording starts.

When CD play finishes, recording stops.

Recording on MDs

20

EN

Fading In and Out (Fader)

You can gradually increase the recording level at the

beginning of a recording (fade-in recording) or

gradually decrease the recording level at the end of a

recording (fade-out recording).

This function is convenient when, for example, you

don’t want the track cut off abruptly when the disc

reaches to its end.

Fade-in recording

During recording pause, press FADER at the position

where you want to start fade-in recording.

Z in “Fade Z 3.2s” flashes and the deck performs the

fade-in recording until the counter reaches “0.0s”.

Fade-out recording

During recording, press FADER at the position where

you want to start fade-out recording.

z in “Fade z 3.2s” flashes and the deck performs the

fade-out recording until the counter reaches “0.0s”.

The deck changes to recording pause when fade-out

recording finishes.

z You can set the duration of fade-in and fade-out

recording independently

1 While the deck is stopped, press MENU/NO twice to

display “Setup Menu”.

2 To set the duration of fade-in recording:

Turn AMS to select “Setup 08”, then press AMS.

To set the duration of fade-out recording:

Turn AMS to select “Setup 09”, then press AMS.

3 Turn AMS to set the duration.

Both the fade-in and fade-out recording durations can

be set in 0.1 second steps.

4 After selecting the duration, press AMS.

5 Press MENU/NO.

FADER

NUM

!

A˜B

CHAR

?

REPEAT

WRITE CLEAR

NAME

/

>

25

(

P.HOLD

A.SPACE

+

STANDBY

=

START

P

STOP

T.REC MUSIC SYNC

REC-IT

)

M.SCAN

0

=

·

)

+ r

P p

CD-SYNC

CD PLAYER FADER

FADER

DIGITAL REC LEVEL

/ANALOG OUT LEVEL

Страница загружается...

Sony MDS-JB920 Руководство пользователя

Похожие модели бренда

Модели других брендов