1998 by Sony Corporation
3-862-110-51(1)
EN
Operating Instructions
Instrukcja obsługi
Инструкция по эксплуатации
PL
EN
RF
MDS-S39
MiniDisc Deck
2
EN
WARNING
To prevent fire or shock
hazard, do not expose the unit
to rain or moisture.
To avoid electrical shock, do
not open the cabinet. Refer
servicing to qualified
personnel only.
The laser component in this product is
capable of emitting radiation exceeding
the limit for Class 1.
This appliance is classified as a CLASS 1
LASER product. The CLASS 1 LASER
PRODUCT MARKING is located on the
rear exterior.
The following caution label is located
inside the unit.
Precautions
On safety
Should any solid object or liquid fall
into the cabinet, unplug the deck and
have it checked by qualified personnel
before operating it any further.
On power sources
• Before operating the deck, check that
the operating voltage of the deck is
identical with your local power
supply. The operating voltage is
indicated on the nameplate at the rear
of the deck.
• If you are not going to use the deck
for a long time, be sure to disconnect
the deck from the wall outlet. To
disconnect the mains lead, grasp the
plug itself; never pull the cord.
• The mains switch is located on the
rear exterior.
• Mains lead must be changed only at
the qualified service shop.
On placement
Do not install the appliance in a
confined space, such as a bookcase or
built-in cabinet because the mains
power switch (MAIN POWER) is
located on the rear exterior.
On operation
If the deck is brought directly from a
cold to a warm location, or is placed in a
very damp room, moisture may
condense on the lenses inside the deck.
Should this occur, the deck may not
operate properly. In this case, remove
the MD and leave the deck turned on
for about an hour until the moisture
evaporates.
On the MiniDisc cartridge
• Do not open the shutter to expose the
MD.
• Do not place the cartridge where it
will be subject to extremes of
sunlight, temperature, moisture or
dust.
On cleaning
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzine.
If you have any questions or problems
concerning your deck, please consult
your nearest Sony dealer.
Welcome!
Thank you for purchasing the Sony
MiniDisc Deck. Before operating the
deck, please read this manual
thoroughly and retain it for future
reference.
About This Manual
Conventions
• Controls in the instructions are those
on the deck; these may, however, be
substituted by controls on the remote
that are similarly named or, when
different, appear in the instructions
within brackets.
• The following icons are used in this
manual:
Z
Indicates a procedure that
requires use of the remote.
z
Indicates tips for making the
task easier and hints.
IN NO EVENT SHALL SELLER BE
LIABLE FOR ANY DIRECT,
INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR
EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR
THE USE OF ANY PRODUCT.
EN
3
EN
TABLE OF CONTENTS
Getting Started
Unpacking ........................................................................................................................... 4
Hooking Up the System.................................................................................................... 4
Recording on an MD.......................................................................................................... 6
Playing an MD ....................................................................................................................... 8
Recording on MDs
Notes on Recording ........................................................................................................... 9
Useful Tips for Recording ................................................................................................ 9
Recording Over Existing Tracks..................................................................................... 11
Adjusting the Recording Level....................................................................................... 11
Marking Track Numbers while Recording (Track Marking) .................................... 12
Starting Recording with 6 Seconds of Prestored Audio Data
(Time Machine Recording) .......................................................................................... 13
Synchro-Recording with Audio Equipment of Your Choice .................................... 14
Synchro-Recording with a Sony CD Player ................................................................. 14
Recording on an MD Using a Timer.............................................................................. 16
Playing MDs
Using the Display.............................................................................................................. 17
Locating a Specific Track ................................................................................................. 18
Locating a Particular Point in a Track ........................................................................... 19
Playing Tracks Repeatedly .............................................................................................. 20
Playing in Random Order (Shuffle Play) ...................................................................... 21
Creating Your Own Programme (Programme Play) .................................................. 21
Useful Tips when Recording from MDs to Tape ........................................................ 22
Playing an MD Using a Timer ........................................................................................ 23
Editing Recorded MDs
Notes on Editing ............................................................................................................... 24
Erasing Recordings (Erase Function) ............................................................................ 24
Erasing a Portion of a Track (A-B Erase Function) ..................................................... 25
Dividing Recorded Tracks (Divide Function).............................................................. 26
Combining Recorded Tracks (Combine Function) ..................................................... 27
Moving Recorded Tracks (Move Function).................................................................. 28
Labelling Recordings (Title Function)........................................................................... 29
Undoing the Last Edit (Undo Function) ....................................................................... 31
Additional Information
Display Messages.............................................................................................................. 32
System Limitations ........................................................................................................... 32
Troubleshooting ................................................................................................................ 33
Specifications ..................................................................................................................... 34
Beep Output During Operations .................................................................................... 35
Guide to the Serial Copy Management System ........................................................... 36
Index .......................................................................................................................................... 38
Getting Started
4
EN
ç
ç
ç
ç
Ç
REC
OUT
TAPE
IN
DIGITAL
OUT
DIGITAL
OUT
DIGITAL
IN
L I N E
(ANALOG)
D I G I T A L
IN
OUT
L
R
IN
OUT
B E E P
ON
OFF
Getting Started
çç
çç
ç : Signal flow
to a wall outlet
(or to a timer during timer
recording or playback)
White
(L)
Red
(R)
White
(L)
Red
(R)
Amplifier
CD player
DAT deck or
MD deck, etc.
Connect only
one digital
component at
a time.
Unpacking
Check that you received the following items:
• Audio connecting cords (2)
• Optical cable (1)
• Remote commander (remote) RM-D27M (1)
• Sony SUM-3 (NS) batteries (2)
Inserting batteries into the remote
You can control the deck using the supplied remote.
Insert two R6 (size-AA) batteries by matching the +
and – on the batteries. When using the remote, point it
at the remote sensor g on the deck.
z When to replace batteries
With normal use, the batteries should last for about six
months. When the remote no longer operates the deck,
replace all the batteries with new ones.
Notes
• Do not leave the remote near an extremely hot or humid
place.
• Do not drop any foreign object into the remote casing,
particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a malfunction.
• If you don’t use the remote for an extended period of time,
remove the batteries to avoid possible damage from
battery leakage and corrosion.
Hooking Up the System
Overview
This section describes how to hook up the MD deck to
an amplifier or other components such as a CD player
or DAT deck. Be sure to turn off the power of each
component before connection.
What cords will I need?
• Audio connecting cords (supplied) (2)
• Optical cables (only one supplied) (2)
Getting Started
5
EN
DIGITALDIGITAL
OUTIN
OUTIN
OPTICAL
ç
Ç
ç
Ç
TAPE/MD
L
R
L
R
INOUT
IN
OUT
LINE
(ANALOG)
Hookups
Connecting the deck to an amplifier
Connect the amplifier to the LINE (ANALOG) IN/OUT
jacks using the audio connecting cords (supplied), making
sure to match the colour-coded cords to the appropriate
jacks on the components: red (right) to red and white (left) to
white. Be sure to make connections firmly to prevent hum
and noise.
Connecting the deck to a digital component such as a CD
player, DAT deck, digital amplifier, or another MD deck
Connect the component through the DIGITAL IN/OUT
connectors with two optical cables (only one supplied).
Take the caps off the connectors and then insert the plugs
parallelly until they click into place.
Be sure not to bend or tie together the optical cables.
z Automatic conversion of digital sampling rates
during recording
A built-in sampling rate converter automatically
converts the sampling frequency of various digital
sources to the 44.1 kHz sampling rate of your MD deck.
This allows you to record sources such as 32- and 48-
kHz DAT or satellite broadcasts, as well as compact
discs and other MDs.
Notes
• If “Din Unlock” or “Cannot Copy” appears in the display,
recording through the digital connector is not possible.
In this case, record the programme source through the
LINE (ANALOG) IN jacks with INPUT set to ANALOG.
• When recording through the DIGITAL IN connector, you
cannot adjust the recording level.
çç
çç
ç: Signal flow
MD deck
Amplifier
çç
çç
ç: Signal flow
MD deck Digital component
Connecting the mains lead
Connect the mains lead to a wall outlet or to the outlet
of a timer.
Turning on the unit
Set MAIN POWER on the rear of the unit to ON.
The unit is turned on in standby mode.
MAIN POWER
ONOFF
MAIN
POWER
Basic Operations
6
EN
MONO
4
Set INPUT to the corresponding input connector.
5
Set REC MODE to the mode you want to record in.
With the arrow
pointing this way
With the label side up
If the MD has a recorded material on it, the deck will
automatically start recording from the end of the last recorded
track.
To record through Set INPUT to
LINE (ANALOG) IN
DIGITAL
ANALOG
DIGITAL IN
To record in Set REC MODE*
1
to
Monaural sound*
2
STEREOStereo sound
*
1
If you switch REC MODE during recording or recording pause, recording
stops.
*
2
In the monaural recording, you can record about two times longer than in
the stereo recording.
Monitor audio during recording
Even if you set REC MODE to
MONO, the monitor signal does
not become monaural.
1
Turn on the amplifier and play the programme source you
want to record.
2
Press 1/u.
The STANDBY indicator turns off.
3
Insert a recordable MD.
•
•
•
•
•
•
•
•
•
•
•
REC LEVEL
(ANALOG)
AMS
PUSH ENTER
0
10
p
·∏
•
•
•
•
•
•
•
REC MODE
INPUT
EDIT/NO YES
STEREO
MONO
ANALOG
REPEAT
DISPLAY/CHAR
SCROLL
PLAY MODE
TIMER
PHONES
LEVEL
REC OFF PLAY
MIN
MAX
r
)
0
§
=
+
DIGITAL
STANDBY
32 68
457
Recording on an MD
Basic Operations
Basic Operations
Basic Operations
7
EN
6
Press r.
The deck becomes ready to record.
7
When recording the analog input signal, adjust the recording
level with REC LEVEL.
The fourth dot is satisfactory for most purposes. For details,
refer to “Adjusting the Recording Level” on page 11.
8
Press fl (or ·).
Recording starts.
9
Start playing the programme source.
Do not disconnect the deck from the power source immediately after
recording
If you do, recorded material may not be saved to the MD. To save the material,
after recording, press § to take out the MD or change the deck to standby by
pressing
1/u
. “TOC” will flash in the display at this time.
After “TOC” stops flashing and goes out, you can pull out the mains lead.
To
Press
Stop recording
Pause recording* fl (or P). Press the button again to
resume recording.
p
Take out the MD § after stopping recording
* Whenever you pause recording, the track number increases by one. For example, if
you paused recording while recording on track 4, the track number increases by
one and recording continues on the new track when restarted.
To protect an MD against accidental erasure
To make it impossible to record on an MD, slide the tab in the direction of
arrow, opening the slot. To allow recording, close the slot.
Rear of the disc
Slide the tab in
the direction of arrow
Record-protect tab
When ”TOC“ flashes in the
display
The deck is currently updating the
Table Of Contents (TOC).
Do not move the deck or pull out
the mains lead. Changes to an MD
made through recording are saved
only when you update the TOC by
ejecting the MD or changing the
deck to standby by pressing 1/u.
Basic Operations
8
EN
4
Press fl (or ·).
The deck starts playing. Adjust the volume on the amplifier.
Playing an MD
z You can locate and play back
a track while the deck is
stopped
1 Turn AMS (or press =
or +) until the number
of the track you want to
play appears.
2 Press AMS or fl (or ·).
z To use headphones
Connect them to PHONES
jack. Use PHONES LEVEL
to adjust the volume.
Adjust the
headphone
volume.
Connect the
headphones.
Pause playing
Stop playing
Do the following:
Press p.
Press fl (or P). Press the button again
to resume playing.
To
Turn AMS counterclockwise (or press
= on the remote).
Go to the preceding track
Go to the next track
Turn AMS clockwise (or press + on
the remote).
Press § after stopping playing.
Take out the MD
With the arrow
pointing this way
With the label side up
1
Turn on the amplifier and set the source selector to the position
for MD deck.
2
Press 1/u.
The STANDBY indicator turns off.
3
Insert an MD.
•
•
•
•
•
•
•
•
•
•
•
REC LEVEL
(ANALOG)
AMS
PUSH ENTER
0
10
p
·∏
•
•
•
•
•
•
•
REC MODE
INPUT
EDIT/NO YES
STEREO
MONO
ANALOG
REPEAT
DISPLAY/CHAR
SCROLL
PLAY MODE
TIMER
PHONES
LEVEL
REC OFF PLAY
MIN
MAX
r
)
0
§
=
+
DIGITAL
STANDBY
32 4
9
EN
Recording on MDs
The MD deck uses the SCMS (Serial Copy Management
System on page 36)
MDs recorded through digital input connector cannot be
copied onto other MDs or DAT tapes through the digital
output connector.
When recording digital signals that have been emphasized
(in the higher frequencies)
The signal is automatically de-emphasized (with attenuation
proportional to the degree of emphasis) and the level of the
de-emphasized signal is indicated on the peak level meters.
When the deck is recording or in recording pause, digital
signals input through DIGITAL IN are output to DIGITAL
OUT with the same sampling rate.
To change the digital input signal to another sampling rate
for output (without recording it to an MD), use Input
Monitor Function (see page 10).
•
•
•
•
•
•
•
•
•
•
•
p
·∏
•
•
•
•
•
•
•
r
)
0
§
=
+
DISPLAY/CHAR
Recording on MDs
Useful Tips for Recording
Checking the remaining recordable time on
the MD
• When you press DISPLAY/CHAR while recording,
the remaining recordable time on the MD appears.
• When you press DISPLAY/CHAR repeatedly while
the deck is stopped, the display changes as follows:
total recorded time, remaining recordable time on
the MD, disc name (see page 17).
(Continued)
Notes on Recording
If “Protected” appears in the display
The MD is record-protected. Close the slot to record on the
disc (see “To protect an MD against accidental erasure” on
page 7).
If “Din Unlock” flashes in the display
• The digital programme source is not connected as you set
with INPUT in Step 4 on page 6.
To continue, connect the programme source properly.
• The programme source is not on.
Turn on the programme source.
Depending on source being recorded, track numbers are
marked in following ways:
• When recording from a CD or MD with INPUT at
DIGITAL and the source connected through DIGITAL IN:
The deck automatically marks track numbers in the same
sequence as the original. If, however, a track is repeated
two or more times (e.g. by single-track repeat play) or two
or more tracks with the same track number (e.g. from
different MDs or CDs) are played, the track or tracks are
recorded as part of a single, continuous track with a single
track number.
If the source is an MD, track numbers may not be marked
for tracks of less than 4 seconds.
• When recording with INPUT at DIGITAL the deck may
not automatically mark track numbers for some CD
players and multi disc players. In these cases, mark the
track numbers afterwards using the deck’s Divide
Function (see “Dividing Recorded Tracks” on page 26).
• When recording from source connected through LINE
(ANALOG) IN with INPUT at ANALOG, and “LEVEL-
SYNC” does not light up (see “Marking Track Numbers
while Recording” on page 12) or when recording from
DAT or satellite broadcasts connected through DIGITAL
IN with INPUT at DIGITAL:
The source will be recorded as a single track. You can
divide the track afterwards using the Divide Function on
page 26 or mark track numbers during recording by using
the Track Marking Function on page 12.
If “LEVEL-SYNC” appears in the display, the deck
automatically marks track numbers when recording
analog source or digital recording of DAT or satellite
broadcasts (see “Marking track numbers automatically”
on page 12).
• When recording from DAT or satellite broadcasts with
INPUT at DIGITAL, the deck automatically marks a track
number whenever the sampling frequency of the input
signal changes.
When “TOC” flashes in the display
The deck is currently updating the Table Of Contents (TOC).
Do not move the deck or pull out the mains lead. Changes
to an MD made through recording are saved only when you
update the TOC by ejecting the MD or changing the deck to
standby by pressing 1/u.
Recording on MDs
10
EN
Monitoring the input signal (Input Monitor)
Before starting recording, you can monitor the selected
input signal through the deck’s output connectors.
1 Press § to remove the MD.
2 Set INPUT according to the input signal you want
to monitor.
When INPUT is at ANALOG
The analog signal input through LINE (ANALOG) IN is
output to DIGITAL OUT after A/D conversion, and
then to the LINE (ANALOG) OUT connectors and
PHONES jack after D/A conversion.
When INPUT is at DIGITAL
The digital signal input through DIGITAL IN is output
to DIGITAL OUT after passing through the sampling
rate converter, and then to the LINE (ANALOG) OUT
connectors and PHONES jack after D/A conversion.
Note
Even if you set REC MODE to MONO, the monitor
signal does not become monaural.
3 Press r.
If INPUT is at ANALOG, “AD-DA” appears in the
display.
If INPUT is at DIGITAL, “-DA”appears in the
display.
If “Auto Cut” appears in the display
(Auto Cut)
There has been no sound input for 30 seconds while
INPUT is set to DIGITAL and the source is connected
through DIGITAL IN. The 30 seconds of silence are
replaced by a blank of about 3 seconds and the deck
changes to recording pause.
z You can turn off the Auto Cut Function
For details, see “If “Smart Space” appears in the
display”.
If “Smart Space” appears in the display
(Smart Space)
There has been an extended silence of 4 to 30 seconds
in length when INPUT is set to DIGITAL and the
source is connected through DIGITAL IN.
The silence is replaced with a blank of about 3 seconds
and the deck continues recording. Note that the tracks
before and after this three-second space may be
recorded as a single track with a single track number.
To turn off the Smart Space Function and Auto Cut
Function
1 During recording pause, press EDIT/NO repeatedly until
“S. Space ?” appears in the display.
2 Press YES.
3 Press EDIT/NO to display “S. Space OFF.”
To turn on the Smart Space Function and Auto Cut
Function again
1 During recording pause, press EDIT/NO repeatedly until
“S. Space ?” appears in the display.
2 Press YES twice to display “S. Space ON”.
Notes
• When you turn off the Smart Space Function, the Auto Cut
Function is also turned off automatically.
• The Smart Space Function and Auto Cut Function are
factory set to on.
• The Smart Space Function does not affect the order of the
track numbers being recorded, even if the blank space
occurs in the middle of a track.
• If you turn off the deck or disconnect the mains lead, the
deck will recall the last setting (on or off) of the Smart
Space and Auto Cut Functions the next time you turn on
the deck.
Playing back tracks just recorded
Do this procedure to immediately play back tracks that
have just been recorded.
Press fl (or ·) immediately after stopping
recording.
Playback starts from the first track of the material just
recorded.
To play from the first track of the MD after recording
1 Press p again after stopping recording.
2 Press fl (or ·).
Playback starts from the first track of the MD.
11
EN
Recording on MDs
Recording Over Existing Tracks
Follow the procedure below to record over existing
material just as you would on an analog cassette tape.
1 Do Steps 1 to 5 in “Recording on an MD” on page
6.
2 Turn AMS (or press = or +) until the
number of the track to be recorded over appears.
3 To record from the start of the track, continue
from Step 6 in “Recording on an MD” on page 7.
z While “TRACK” flashes in the display
The deck is recording over an existing track, and stops
flashing when it reaches the end of the recorded
portion.
z To record from the middle of the track
1 After Step 2 above, press fl (or ·) to start
playback.
2 Press fl (or P) where you want to start recording.
3 Continue from Step 6 in “Recording on an MD” on
page 7.
Note
You cannot record from the middle of an existing track when
the “PROGRAM” or “SHUFFLE” is on.
Adjusting the Recording Level
When recording with INPUT at ANALOG and the
signal input through LINE (ANALOG) IN jacks, use
REC LEVEL to adjust the recording level before
starting recording.
You cannot adjust the recording level during digital
recording.
1 Do Steps 1 to 6 in “Recording on an MD” on
pages 6 and 7.
2 Play the portion of the programme source with
the strongest signal level.
3 While monitoring the sound, turn REC LEVEL to
adjust the recording level so that the peak level
meters reach their highest point without turning
on the OVER indication. Occasional lighting of
“OVER” is acceptable.
4 Stop playing the programme source.
5 To start recording, do the procedure starting from
Step 8 in “Recording on an MD” on page 7.
Without turning on the OVER indication
=/+
r
6
)0
+=
pP·
= AMS +
•
•
•
•
•
•
•
•
•
•
•
p
·∏
•
•
•
•
r
)
0
§
=
+
•
•
•
•
•
•
•
•
•
•
•
p
·∏
•
•
•
•
•
•
•
r
)
0
§
=
+
REC LEVEL
Recording on MDs
12
EN
Marking Track Numbers while
Recording (Track Marking)
You can mark track numbers either manually or
automatically. By marking track numbers at specific
points, you can quickly locate the points later using the
AMS Function or Editing Functions.
1 Press EDIT/NO to display “LevelSync ?”during
recording or recording pause.
2 Press YES twice to display “LevelSync ON.”
“LEVEL-SYNC” appears in the display.
To cancel Automatic Track Marking
1 Press EDIT/NO during recording or recording pause.
“LevelSync ?” appears in the display.
2 Press YES.
3 Press EDIT/NO.
“LevelSyncOFF” appears in the display.
* The signal level must remain low for 2 or more seconds
before a new track number is marked.
z When you want to mark track numbers after you‘ve
finished recording
Use the Divide Function (see “Dividing Recorded
Tracks” on page 26).
Note
If you turn off the deck or disconnect the mains lead, the
deck will recall the last setting (LevelSync on or off) of the
Automatic Track Marking Function the next time you turn
on the deck.
Marking track numbers manually
(Manual Track Marking)
You can mark track numbers at any time while
recording on an MD.
Press r at the place you want to add a track mark
while recording.
Marking track numbers automatically
(Automatic Track Marking)
The deck adds track marks differently in the following
cases:
• When recording from CDs or MDs with INPUT at
DIGITAL and the source connected through
DIGITAL IN:
The deck marks track numbers automatically. When
you record from a CD or MD, the track numbers are
marked as they are found on the original. However,
the deck may not automatically mark track numbers
for some CD players and multi disc players.
• When recording with INPUT at ANALOG and the
source connected through LINE (ANALOG) IN, or
when recording from DAT or satellite broadcasts
with INPUT at DIGITAL and the DAT or satellite
broadcasts connected through DIGITAL IN:
The deck marks a new track number whenever the
signal level drops and rises to a certain point*
(Automatic Track Marking). If “LEVEL-SYNC” does
not light up, set the LevelSync to ON as follows:
•
•
•
•
•
•
•
•
•
•
•
p
·∏
•
•
•
•
•
•
•
r
)
0
§
=
+
YESEDIT/NO
r
13
EN
Recording on MDs
3 Press AMS (or T.REC) to start Time Machine
Recording.
Recording of the programme source starts with
the 6 seconds of audio data stored in the buffer
memory.
z To stop Time Machine Recording
Press p.
Note
The deck starts storing audio data when the deck is in
recording pause and you start playing the programme
source. With less than 6 seconds of playing of the
programme source and audio data stored in the buffer
memory, Time Machine Recording starts with less than
6 seconds of audio data.
Starting Recording with
6 Seconds of Prestored Audio
Data (Time Machine Recording)
When recording from an FM or satellite broadcast, the
first few seconds of material are often lost due to the
time it takes you to ascertain the contents and press the
record button. To prevent the loss of this material, the
Time Machine Recording Function constantly stores
6 seconds of the most recent audio data in a buffer
memory so that when you begin recording the
programme source, the recording actually begins with
the 6 seconds of audio data stored in the buffer
memory in advance, as shown in the illustration below:
1 Do Steps 1 to 6 in “Recording on an MD” on
pages 6 and 7.
The deck changes to recording pause.
2 Start playing the programme source you want to
record.
The most recent 6 seconds of audio data is stored
in the buffer memory.
End of the programme
source to be recorded
Time
Recorded
portion
When you press
AMS in Step 3
Audio data in 6-second buffer memory
Beginning of the programme
source to be recorded
r
6
)0
+=
pP·
T.REC
= AMS +
•
•
•
•
•
•
•
•
•
•
•
p
·∏
•
•
•
•
r
)
0
§
=
+
Recording on MDs
14
EN
Synchro-Recording with Audio
Equipment of Your Choice Z
By using the MUSIC SYNC button on the remote, you
can automatically start recording in sync with the
signal input from the programme source through the
LINE (ANALOG) IN jacks or the DIGITAL IN
connector (Music Synchro-Recording).
The method of marking track numbers differs,
depending on the programme source being recorded
and how the deck is connected to the programme
source. (See “Notes on Recording” on page 9.)
1 Do Steps 1 to 5 in “Recording on an MD” on page
6.
2 Press MUSIC SYNC.
The deck changes to recording pause.
3 Start playing the programme source you want to
record.
The deck starts recording automatically.
z To stop Music Synchro-Recording
Press p.
Note
When Music Synchro-Recording, the Smart Space Function
and the Auto Cut Function turn on automatically regardless
of their setting (on or off) and type of input (digital or
analog).
Synchro-Recording with a Sony
CD Player Z
By connecting your deck to a Sony CD player or Hi-Fi
Component System, you can easily dub CDs onto MDs
using the CD synchro buttons on the remote. If your
deck is connected to a Sony CD player by a digital
input cable, track numbers are automatically marked
as appear on the original regardless of whether
“LevelSync ON” or “LevelSyncOFF” is selected. If
your deck is connected to a Sony CD player by audio
connecting cords through LINE (ANALOG) IN, track
numbers are automatically marked when you select
“LevelSync ON” (see “Marking Track Numbers while
Recording” on page 12).
As the same remote controls both the CD player and
the deck, you may have trouble operating both units if
they are far from each other. If you do, place the CD
player close to this deck.
1 Set the source selector on the amplifier to CD.
2 Do Steps 2 to 5 in “Recording on an MD” on page
6 to prepare the deck for recording.
3 Insert a CD into the CD player.
4 Select the playback mode (Shuffle Play,
Programme Play, etc.) on the CD player.
r
6
)0
+=
pP·
MUSIC SYNC
r
6
)0
+=
+=P
pP·
STOP
CD PLAYER P
START
STANDBY
15
EN
Recording on MDs
z
You can also do synchro-recording with a Sony video
CD player
Using the procedure for synchro-recording with a Sony
CD player, you can do synchro-recording with a Sony
video CD player also.
To select the video CD player, press button number 2
while pressing down the 1/u button before starting the
procedure.
To select the CD player again, press button number 1
while pressing down the 1/u button.
The deck is factory set to a CD player for synchro-
recording.
z You can check the remaining recordable time on the
MD
Press DISPLAY (see page 17).
5 Press STANDBY.
The CD player pauses for playing and the deck
pauses for recording.
6 Press START.
The deck starts recording and the CD player starts
playback.
The track number and elapsed recording time of
the track appear in the display.
If the CD player does not start playing
Some CD player models may not respond when you
press START on the remote of the deck. Press P on the
remote of the CD player instead.
7 Press STOP to stop synchro-recording.
To pause recording
Press STANDBY or CD PLAYER P.
To restart recording, press START or CD PLAYER P.
A new track number is marked each time you pause
recording.
Note
When using the supplied remote for synchro-recording, set
the mode selector on the CD player to CD1.
z You can use the remote of the CD player during
synchro-recording
When you press p, the CD player stops and the deck
pauses for recording.
When you press P, the CD player pauses and the deck
pauses for recording.
To restart synchro-recording, press ·.
z You can change CDs during synchro-recording
Do the following steps instead of Step 7 above.
1 Press p on the remote of the CD player.
The deck pauses for recording.
2 Change the CD.
3 Press · on the remote of the CD player.
Synchro-recording restarts.
Recording on MDs
16
EN
Recording on an MD Using a
Timer
By connecting a timer (not supplied) to the deck, you
can start and stop recording operations at specified
times. For further information on connecting the timer
and setting the starting and ending times, refer to the
instructions that came with the timer.
1 Do Steps 1 to 7 in “Recording on an MD” on
pages 6 and 7.
2 • If you want to specify the time for the start of
recording, press p.
• If you want to specify the time for the end of
recording, do Steps 8 and 9 of “Recording on an
MD” on page 7.
• If you want to specify the time for both start
and end of recording, press p.
3 Set TIMER on the deck to REC.
4 Set the timer as required.
• When you have set the time for the start of
recording, the deck turns off. When the
specified time arrives, the deck turns on and
starts recording.
• When you have set the time for the end of
recording, recording continues. When the
specified time arrives, the deck stops recording
and turns off.
• When you have set the time for both the start
and end of recording, the deck turns off. When
the starting time arrives, the deck turns on and
starts recording. When the ending time arrives,
the deck stops recording and turns off.
5 After you have finished using the timer, set
TIMER on the deck to OFF. Then place the deck
in standby status by plugging the mains lead of
the deck into a wall outlet or set the timer to
continuous operation.
• If TIMER is left at REC, the deck will
automatically start recording the next time you
turn the deck on.
• If you do not change the deck to standby status
for more than a month after timer recording has
finished, the recorded contents may disappear.
Make sure to change the deck to standby status within a
month after timer recording is completed
The TOC on the MD is updated and recorded contents are
written to the MD when you turn the deck on. If the
recorded contents have disappeared, “STANDBY” flashes
when you turn the deck on.
Notes
• It may take about 30 seconds after the deck is turned on
until recording starts. When recording at a specified time
using the timer, be sure to take this time into account
when setting the recording start time.
• During timer recording, new material is recorded from the
end of the recorded portion on the MD.
• Material recorded during timer recording will be saved to
the disc the next time you turn the deck on. “TOC” will
flash in the display at that time. Do not move the deck or
pull out the mains lead while “TOC” is flashing.
• Timer recording will stop if the disc becomes full.
•
•
•
•
•
•
•
•
•
•
•
p
·∏
•
•
•
•
•
•
•
r
)
0
§
=
+
TIMER
p
17
EN
Playing MDs
When you insert an MD, the disc name, total number
of tracks, and total disc playing time appear in the
display as follows:
Total number of tracks Total disc playing time
The disc name appears, followed by the total number
of tracks (Tr) and total disc playing time.
A music calendar showing all the track numbers
appears within a grid if the MD is a premastered disc,
or without a grid if the MD is a recordable disc.
If the total track number exceeds 25, z appears to the
right of number 25 in the music calendar.
To label a recordable disc and its tracks, see
“Labelling Recordings” on page 29.
Note
When you insert a new MD or turn off the deck and turn it
on again, the last item displayed will reappear.
If, however, you disconnect the mains lead, the display will
show the total track number and total playing time of all
recorded tracks the next time you turn on the deck, no
matter what the last display was.
(Continued)
Disc name Music calendar
Checking the total track number, total disc
playing time, remaining recordable time of
the disc and the title of the disc
Each time you press DISPLAY/CHAR (or DISPLAY)
while the deck is stopped, you can change the display
as follows:
Remaining recordable time of the disc
(Recorded MDs only)
Disc name
Press
Press
The remaining recordable time of the disc
is not shown for premastered MDs.
Press
Total track number and total playing
time of all recorded tracks
6
pP·
SCROLLDISPLAY
√
√
√
•
•
•
•
•
•
•
•
•
•
•
p
·∏
•
•
•
•
•
•
•
r
)
0
§
=
+
SCROLL
DISPLAY/CHAR
Playing MDs
Using the Display
You can use the display to check disc and track
information such as the total track number, total
playing time of the tracks, remaining recordable time
of the disc and disc name.
18
EN
Playing MDs
Locating a Specific Track
You can quickly locate any track while playing a disc
by using AMS (Automatic Music Sensor), = and
+, number buttons or M.SCAN on the remote.
z You can check the track name at any time while
playing an MD
Press SCROLL.
Since the display shows up to 12 characters at a time,
press SCROLL again to see the rest of the track title if
the title has 13 characters or more.
Press SCROLL again to pause scrolling, and again to
continue scrolling.
Do the following:
The next or
succeeding tracks
During playback, turn AMS clockwise
(or press + repeatedly) until you
find the track.
The current or
preceding tracks
During playback, turn AMS
counterclockwise (or press =
repeatedly) until you find the track.
A specific track
directly
Z
Press number buttons to enter the
track number.
A specific track by
using AMS
1 Turn AMS until the track number
you want to locate appears while
the deck is stopped. (The track
number is flashing.)
2 Press AMS or fl.
To locate
By scanning each
track for 6 seconds
(music scan)
Z
1 Press M.SCAN before you start
playing.
2 When you find the track you want,
press · to start playing.
Number
buttons
Checking remaining time and the title of a
track
Each time you press DISPLAY/CHAR (or DISPLAY)
while playing an MD, you can change the display as
shown below. The track numbers in the music
calendar disappear after they are played.
Track number and playing time of the
current track
Track number and remaining time of
the current track
Press
Press
Track name
Press
If no title is recorded, “No Name” appears,
followed by the elapsed playing time.
√
√
r
6
)0
+=
pP·
M.SCAN
>25
·
=/+
•
•
•
•
•
•
•
•
•
•
•
p
·∏
•
•
•
•
r
)
0
§
=
+
= AMS +
19
EN
Playing MDs
Locating a Particular Point in a
Track
You can also use 0 and ) to locate a particular
point in a track during playback or playback pause.
To locate a point Press
While monitoring the
sound
) (forward) or 0 (backward)
and keep pressing until you find
the point.
Quickly by observing
the display during
playback pause
) or 0 and keep pressing
until you find the point. There is
no sound output during this
operation.
Notes
• If the disc reaches the end while you are pressing )
during playback pause, “OVER” appears in the display.
Press 0 (or =) or turn AMS counterclockwise to go
back.
• If the disc reaches the end while you are pressing )
during sound monitoring, the deck stops.
• Tracks that are only a few seconds long may be too short
to scan using the search function. For such tracks, it is
better to play the MD at normal speed.
z When you directly locate a track with a number over
25 Z
You must press >25 first, before entering the
corresponding digits.
Press >25 once if it is a 2-digit track number, and twice
if it is a 3-digit track number.
To enter “0,” press button 10.
Examples: • To play track number 30
Press >25 once, then 3 and 10.
• To play track number 100
Press >25 twice, then 1, 10 and 10.
z You can extend the playing time during music scan
Z
While the deck is stopped, press M.SCAN repeatedly
until the playing time you want (6, 10 or 20 seconds)
appears in the display. Each press changes the time in
order of 6 to 20, then from 6 again.
z To pause playing at the beginning of a track
Turn AMS (or press = or +) after pausing
playback.
z To go quickly to the beginning of the last track
Turn AMS counterclockwise (or press =) while the
display shows the total track number and total disc
playing time, remaining recordable time of the disc, or
disc name (see page 17).
•
•
•
•
•
•
•
•
•
•
•
p
·∏
•
•
•
•
•
•
•
r
)
0
§
=
+
0/)
20
EN
Playing MDs
Playing Tracks Repeatedly
You can play tracks repeatedly in any play mode.
Press REPEAT.
“REPEAT” appears in the display.
The deck repeats the tracks as follows:
When the MD is
played in
Normal play (page 8)
Shuffle Play (page 21)
Programme Play (page 21)
The deck repeats
All the tracks
To cancel repeat play
Press REPEAT several times until “REPEAT” disappears.
The deck returns to the original playing mode.
Repeating the current track
While the track you want to repeat is playing in
normal play, press REPEAT several times until
“REPEAT 1” appears in the display.
Repeating a specific portion (A-B Repeat)
Z
You can play a specific portion of a track repeatedly.
This might be useful when you want to memorize
lyrics.
Note that you can only repeat a portion within the
boundaries of a single track.
1 While playing a disc, press A˜B at the starting
point (point A) of the portion to be played
repeatedly.
“REPEAT A-” flashes in the display.
2 Continue playing the track or press ) until you
reach the ending point (point B), then press A˜B
again.
“REPEAT A-B” lights continuously. The deck
starts to play the specified portion repeatedly.
To cancel A-B Repeat
Press REPEAT or p.
Setting new starting and ending points
You can repeat the portion immediately after the currently
specified portion by changing the starting and ending
points.
1 Press A˜B while “REPEAT A-B” appears.
The current ending point B becomes the new starting
point A and “REPEAT A-” flashes in the display.
2 Continue playing the track or press ) until you reach
the new ending point (point B), then press A˜B again.
“REPEAT A-B” lights continuously and the deck starts
playing repeatedly the newly specified portion.
Note
If you turn off the deck or disconnect the mains lead, the
deck will recall the last setting of the Repeat Function the
next time you turn on the deck.
The A-B Repeat settings, however, are lost.
All the tracks in random order
The same programme
r
6
)0
+=
pP·
REPEAT
A˜B
)
•
•
•
REPEAT
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/