Sony MDS-S40 Инструкция по применению

3-865-729-51(1)

MiniDisc Deck

 1999 by Sony Corporation

MiniDisc Deck MDS-S40

MDS-S40

Operating Instructions

Instrukcja obsługi

Инструкция по эксплуатаци

GB

PL

RU

2

GB

WARNING

To prevent fire or shock

hazard, do not expose the

unit to rain or moisture.

To avoid electrical shock,

do not open the cabinet.

Refer servicing to qualified

personnel only.

This appliance is classified as a CLASS 1

LASER product.

The CLASS 1 LASER PRODUCT

MARKING is located on the rear exterior.

IN NO EVENT SHALL SELLER BE

LIABLE FOR ANY DIRECT,

INCIDENTAL OR CONSEQUENTIAL

DAMAGES OF ANY NATURE, OR

LOSSES OR EXPENSES RESULTING

FROM ANY DEFECTIVE PRODUCT OR

THE USE OF ANY PRODUCT.

Welcome!

Thank you for purchasing the Sony

MiniDisc Deck. Before operating the

deck, please read this manual

thoroughly and retain it for future

reference.

About This

Manual

The instructions in this manual are for

the MDS-S40 MiniDisc Deck.

Conventions

• Controls in these instructions are

those on the deck; these may,

however, be substituted by controls

on the supplied remote that are

similarly named, or, when different,

appear in the instructions within

parentheses.

Example: Turn AMS clockwise (or

press > repeatedly).

• The following icons are used in this

manual:

ZIndicates a procedure that

requires use of the remote.

z Indicates hints and tips for

making the task easier.

3

GB

TABLE OF CONTENTS

Getting Started 4

Before You Start the Hookup 4

Hooking Up the Audio Components 5

Location and Function of Parts 8

Front Panel Parts Description 8

Remote Parts Description 10

Using the Display 11

Recording on MDs 13

Notes on Recording 13

Recording on an MD 14

Adjusting the Recording Level 16

Recording Tips 16

Marking Track Numbers While Recording

(Track Marking) 17

Starting Recording With Six Seconds of Prestored

Audio Data (Time Machine Recording) 18

Synchro-recording With the Audio Component of

Your Choice (Music Synchro-recording) 19

Synchro-recording With a Sony CD Player

(CD Synchro-recording) 19

Playing MDs 21

Playing an MD 21

Playing a Specific Track 22

Locating a Particular Point in a Track 23

Playing Tracks Repeatedly 23

Playing Tracks in Random Order (Shuffle Play) 24

Creating Your Own Program (Program Play) 25

Tips for Recording From MDs to Tape 26

Editing Recorded MDs 28

Erasing Tracks 29

Dividing Tracks 31

Combining Tracks 32

Moving Tracks 32

Naming a Track or MD 33

Undoing the Last Edit 36

Other Functions 37

Fade In and Fade Out 37

Falling Asleep to Music (Sleep Timer) 38

Additional Information 39

Precautions 39

Handling MDs 40

System Limitations 40

Troubleshooting 41

Specifications 41

Display Messages 42

Edit Menu Table 43

Setup Menu Table 44

Self-Diagnosis Function 44

Using the Beeps 45

Index 46

4

GB

Before You Start the

Hookup

Checking the supplied accessories

This MD deck comes with the following items:

• Audio connecting cords (2)

• Optical cable (1)

• Remote commander (remote) RM-D29M (1)

• R6 (size-AA) batteries (2)

Inserting batteries into the remote

Insert two R6 (size-AA) batteries with the + and –

properly oriented to the markings into the battery

compartment. When using the remote, point it at the

remote sensor

on the deck.

z

When to replace the batteries

Under normal conditions, the batteries should last for about six

months. When the remote no longer operates the deck, replace

both batteries with new ones.

Notes

• Do not leave the remote in an extremely hot or humid place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not use a new battery with an old one.

• Do not expose the remote sensor to direct sunlight or lighting

apparatus. Doing so may cause a malfunction.

• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from battery

leakage and corrosion.

Getting

Started

This chapter provides information on

the supplied accessories, things you

should keep in mind while hooking

up the system, and how to connect

various audio components to the MD

deck. Be sure to read this chapter

thoroughly before you actually

connect anything to the deck.

5

GB

Getting Started

Hooking Up the Audio Components

DIGITAL BEEP

(ANALOG)

IN

ON OFF

LINE

OUT

L

R

IN

MD

IN

L

R

OUT

DIGITAL

OUT

Required cords

Audio connecting cords (2) (supplied)

When connecting an audio connecting cord, be sure to match the

color-coded pins to the appropriate jacks: white (left) to white

and red (right) to red.

Optical cable (1) (supplied)

• When connecting an optical cable, take the caps off the

connectors and insert the cable plugs straight in until they click

into place.

• Do not bend or tie the optical cable.

White (L) White (L)

Red (R) Red (R)

Things you should keep in mind while

hooking up the system

• Turn off the power to all components before making

any connections.

• Do not connect any AC power cord until all the

connections are completed.

• Be sure the connections are firm to prevent hum and

noise.

Jacks (connectors) for connecting audio

components

Connect To the

Amplifiers LINE (ANALOG) IN/OUT jacks

BEEP switch (page 45)

Amplifier, etc.

Digital amplifier, DAT deck,

MD deck, CD player, DBS

tuner, etc.

AC power cord

Digital amplifiers, DAT

decks, another MD deck, CD

players, or DBS tuners

DIGITAL IN connector

6

GB

Getting Started

Setting the voltage (only on models

supplied with a voltage selector)

Make sure the voltage selector on the rear panel of the

deck is set to the voltage of the local power supply. If not,

use a screwdriver to change it to the correct position

before connecting the AC power cord to a wall outlet.

VOLTAGE SELECTOR

110–120V 220–240V

Connecting the AC power cord

Connect the AC power cord of the deck to a wall outlet.

Note

Do not connect the AC power cord to a switched outlet.

Hooking Up the Audio Components

7

GB

Getting Started

8

GB

Front Panel Parts

Description

Location and

Function of

Parts

This chapter tells you about the

location and function of the various

buttons and controls on the front

panel and the supplied remote.

Further details are provided on the

pages indicated in the parentheses.

It also tells you about the information

that appears in the display window.

1 ~/1 (power) switch (14, 21)

Press to turn the deck on. When you turn the deck on,

the switch indicator turns off. When you press the

switch again, the deck turns off and the indicator

lights up red.

2 SCROLL button (12)

Press to scroll the name of a track or MD.

3 LEVEL/DISPLAY/CHAR button (12, 16, 25, 33)

• Press during recording or recording pause to adjust

the recording level.

• Press when the deck is stopped to display disc

information or the contents of a program.

• Press during recording to display information on the

track being recorded.

• Press during play to display information on the

current track.

• Press while editing an MD to select the type of

characters to be input.

4 Display window (11, 12)

Shows various information.

5 MD insertion slot (14, 21)

Insert the MD as illustrated below.

With the labeled side up

With the arrow pointing towards the deck

9

GB

Location of Parts and Brief Explanations

1 6 87 9 0 qa2 3 54

qsqdqg qfqhqjqkql

` / 1

N

zxX

Z

>.

mM

EJECT

MENU/NO YES

AMS

CLEAR PUSH ENTER

SCROLL

PLAY MODE

INPUT

ANALOGDIGITAL

••

DISPLAY/CHAR

LEVEL/

REPEAT

6 EJECT Z button (15, 21)

Press to eject the MD.

7 MENU/NO button (14, 29, 38)

Press to display “Edit Menu” or “Setup Menu.”

8 N button (15, 21)

Press to start play.

9 X button (15, 21)

Press to pause play or recording. Press again to

resume play or recording.

q; x button (15, 21, 29)

Press to stop play, stop recording, or cancel the

selected operation.

qa z button (15-17)

Press to record on the MD, monitor the input signal, or

mark track numbers.

qs YES button (14, 25, 29, 38)

Press to carry out the selected operation.

qd AMS control (14-16, 21, 25, 29, 33, 38)

Turn to locate tracks, adjust the recording level, select

the input characters, or select a menu item.

qf m/M buttons (23, 25, 30, 33)

Press to locate a portion within a track, change the

contents of a program, or change the input character.

qg CLEAR button (26, 34)

Press to cancel the selection.

qh REPEAT button (23, 24)

Press to play tracks repeatedly.

qj PLAY MODE button (24)

Press to select Shuffle Play or Program Play.

qk INPUT switch (14)

Use to select the input jack (or connector) of the

program source to be recorded.

ql Remote sensor (4)

Point the remote towards this window (

) for

remote operations.

10

GB

Location of Parts and Brief Explanations

Remote Parts Description

1

2

3

4

6

9

0

qs

7

ws

wa

qa

w;

qh

qk

qj

qd

qf

qg

ql

5

8

ABC

LEVEL

CD-SYNC

MUSIC

SYNC

A

y

B

REPEAT

2

DEF

3

& ! ?

FADERSCROLL

DISPLAY

PLAY MODE

NAME IN

CLEARYES

MENU/NO

CHARNAME

1

JKL

5

MNO

6

GHI

4

TUV

8

QZ

10/0

T.REC

>

10

WXY

9

PRS

7

CD PLAYER

STANDBY

STOP

START

. >

m M

z x

X

H

Z

` / 1

+

–

>.X

1 ~/1 (power) switch (14, 21)

Press to turn the deck on. When you turn the deck on,

the ~/1 switch indicator on the deck turns off. When

you press the switch again, the deck turns off and the

indicator lights up red.

2 CLEAR button (26, 34)

Press to cancel the selection.

3 FADER button (37)

Press to perform Fade-in Play/Recording or Fade-out

Play/Recording.

4 PLAY MODE button (24)

Press to select Shuffle Play or Program Play.

5 Letter/number buttons (22, 34)

Press to enter a track number directly or input letters

or numbers.

6 MUSIC SYNC button (19)

Press to start Music Synchro-recording.

7 CD-SYNC STOP button (20)

Press to stop CD Synchro-recording.

CD-SYNC START button (19)

Press to start CD Synchro-recording.

CD-SYNC STANDBY button (19)

Press to enter standby for CD Synchro-recording.

8 CD PLAYER X button (20)

Press to pause the CD play. Press again to resume CD

play.

CD PLAYER ./> buttons (20)

Press to locate tracks on the CD.

9 X button (15, 21)

Press to pause play or recording. Press again to

resume play or recording.

q; x button (15, 21, 29)

Press to stop play, stop recording, or cancel the

selected operation.

qa LEVEL +/– buttons (16)

Press to adjust the recording level.

qs AyB button (24)

Press to select Repeat A-B Play.

qd REPEAT button (23, 24)

Press to play tracks repeatedly.

qf m/M buttons (23, 25, 30, 34)

Press to locate a portion within a track, change the

contents of a program, or shift the cursor to the right.

11

GB

Location of Parts and Brief Explanations

qg ./> buttons (14-16, 21, 25, 29, 34, 38)

Press to locate tracks, adjust the recording level, or

select a menu item.

qh z button (15-17)

Press to record on the MD, monitor the input signal, or

mark track numbers.

qj T.REC button (18)

Press during recording pause to start Time Machine

Recording.

qk H button (15, 21)

Press to start play.

ql NAME button (34)

Press to add the name or change the name of a track or

MD.

CHAR button (34)

Press to select the type of characters to be input when

naming a track or MD.

w; DISPLAY button (12, 16, 25)

Press to select the information to be displayed in the

window.

SCROLL button (12)

Press to scroll the name of a track or MD.

wa MENU/NO button (14, 29, 38)

Press to display “Edit Menu” or “Setup Menu.”

YES button (14, 25, 29, 38)

Press to carry out the selected operation.

ws Z button (15, 21)

Press to eject the MD.

Using the Display

The display window shows information about the MD or

track. This section describes the information that appears

for each deck status.

LEVEL/DISPLAY/CHAR

` / 1

N

zxX

Z

>.

mM

Note

The type of information (e.g., total number of tracks, recorded

time, remaining time, track or disc name) which was last

displayed will continue to appear until you change it by pressing

LEVEL/DISPLAY/CHAR (or DISPLAY), even if you change the

deck operation status. For example, if the remaining time was

displayed when you stop the deck, the remaining time will

continue to appear when you begin playing the same MD again

or a different one.

When you insert an MD

The display automatically changes as follows:

SONGS

15 46m 08s

Disc name

Total number of tracks Total recorded time

12

GB

Location of Parts and Brief Explanations

While the deck is stopped

Press LEVEL/DISPLAY/CHAR (or DISPLAY) repeatedly to

change the display.

Each press of the button changes the display as follows:

15 46m 08s

SONGS

-27m 52s

*

Not shown for the premastered discs.

**

When the MD has no name, “No Name” appears, followed by the

default display.

While the deck is recording

Press LEVEL/DISPLAY/CHAR (or DISPLAY) repeatedly to

change the display.

Each press of the button changes the display as follows:

16 3m 05s

BALLAD

-24m 47s

*

When the track has no name, “No Name” appears, followed by the

default display.

Total number of tracks and total

recorded time (default display)

Press

Remaining recordable time on the

MD (recordable MDs only)*

Press

Using the Display

Track number and recorded time of

the current track (default display)

Disc name**

Press

While the deck is playing

Press LEVEL/DISPLAY/CHAR (or DISPLAY) repeatedly to

change the display.

Each press of the button changes the display as follows:

2 3m 33s

DIARY

2 -1m 25s

*

When the track has no name, “No Name” appears, followed by the

default display.

z

You can check the track name at any time while playing

Press SCROLL.

The track name appears and scrolls. While the track name is

scrolling, press the button again to pause scrolling, and again to

continue scrolling.

Press

Remaining recordable time on the

MD

Press

Level of the input signal

Press

Track name*

Press

Track number and elapsed time of

the current track (default display)

Press

Track number and remaining time of

the current track

Press

Track name*

Press

13

GB

Recording on MDs

Recording on

MDs

This chapter explains the various

ways to record to an MD, as well as

how to mark track numbers and

perform synchro-recording with other

components.

Notes on Recording

About indications which appear while

recording

When “Protected” and “C11” alternate in the

display

The record-protect slot is open and the MD is record-

protected. To record on the MD, slide the tab to close the

slot. For details, see “To prevent accidental erasure of the

recorded material” on page 15.

When “Din Unlock” and “C71” alternate in the

display

• The digital component selected with the INPUT switch

is not connected correctly. Check the connection.

• The selected digital component is not turned on. Turn

on the component.

When “Cannot Copy” appears in the display

The MD deck uses the Serial Copy Management System.

MDs recorded through the digital input connector can’t be

copied to other MDs or DAT tapes through the digital

output connector. For details, see “Guide to the Serial

Copy Management System” on page 14.

When “TRACK” flashes in the display

The MD deck is recording over existing track(s)

(“Recording on an MD” on page 14). The indication stops

flashing when the deck reaches the end of the recorded

portion.

About indications which appear after

recording

When “TOC” lights up in the display

Recording has finished but the TOC (Table of Contents)

on the MD has not been updated to reflect the recording

results. The recording will be lost if you disconnect the

AC power cord while the indication is on. The TOC will

be updated only when you eject the MD or turn off the

MD deck.

When “TOC Writing” flashes in the display

The deck is updating the TOC. Do not disconnect the AC

power cord or move the deck while the indication flashes.

14

GB

Recording on MDs

Automatic conversion of digital sampling

rates during recording

A built-in sampling rate converter automatically converts

the sampling frequency of various digital sources to the

44.1 kHz sampling rate of the MD deck. This allows you

to monitor and record sources such as 32- or 48-kHz DAT

tapes or satellite broadcasts, as well as the CDs and MDs.

Automatic de-emphasizing of input

signals for digital recording

When recording digital input signals that have been

emphasized in higher frequencies, the deck automatically

de-emphasizes the signals with attenuation proportional

to the degree of emphasis. The level of the de-

emphasized signal is indicated on the peak level meters.

Guide to the Serial Copy Management

System

Digital audio components, such as CDs, MDs, and DATs

make it easy to produce high-quality copies of music by

processing music as a digital signal.

To protect copyrighted music sources, this deck uses the

Serial Copy Management System which allows you to

make only a single copy of a digitally recorded source

through digital-to-digital connections.

You can make only a first-generation copy

*

through a digital-to-digital connection.

Examples are given as follows:

• You can make a copy of a commercially available digital

sound program (for example, a CD or MD), but you

can’t make a second copy from the first-generation

copy.

• You can make a copy of a digital signal from a digitally

recorded analog sound program (for example, an

analog record or a music cassette tape) or from a digital

satellite broadcast program, but you can’t make a

second copy from the first-generation copy.

*

A first-generation copy means the first recording of a digital audio

source through the deck’s digital input connector. For example, if you

record from a CD player connected to the DIGITAL IN connector,

that copy is a first-generation copy.

Note

The restrictions of the Serial Copy Management System don’t

apply when you make a recording through the analog-to-analog

connections.

Recording on an MD

The operations for normal recording are explained below.

If the MD has recorded material on it, the deck will

automatically start recording from the end of the recorded

portion.

INPUT AMS YESMENU/NO

EJECT Zz

N?/1 X x

` / 1

N

zxX

Z

>.

mM

1 Turn on the amplifier and program source, and

select the source on the amplifier.

2 Press ~/1 to turn on the deck.

The switch indicator turns off.

3 Insert a recordable MD.

4 Set INPUT to the position that corresponds to the

input jacks (connector) connected to the program

source.

If the source is connected to the Set INPUT to

DIGITAL IN connector DIGITAL

LINE (ANALOG) IN jacks ANALOG

5 Press MENU/NO twice.

“Setup Menu” appears in the display.

6 Turn AMS (or press ./> repeatedly) until

“Stereo Rec” or “Mono Rec” appears in the display,

then press AMS or YES.

7 Turn AMS (or press ./> repeatedly) to select

the recording mode, then press AMS or YES.

To record in Select

Stereo Stereo Rec (factory setting)

Monaural Mono Rec

Monaural mode allows you to record about twice as

much material as stereo.

8 Press MENU/NO.

Notes on Recording

15

GB

Recording on MDs

9 If necessary, locate the point on the MD to start

recording from.

If you want to record on a new MD or start recording

from the end of the recorded portion, go to step 10.

To record over from the beginning of an existing MD

track

Turn AMS (or press ./> repeatedly) until the

number of the track to be recorded over appears.

To record over from the middle of an MD track

Turn AMS (or press ./> repeatedly) until the

number of the track to be recorded over appears, then

press N to start playback. Press X at the point you

want to start recording from.

10Press z.

The deck changes to recording pause.

11If you have set INPUT to ANALOG in step 4 above,

adjust the recording level.

For details, see “Adjusting the Recording Level” on

page 16.

12Press N or X.

Recording starts.

13Start playing the program source.

Operations you may want to do during recording

To Press

Stop recording x

Pause recording X

Resume recording after pausing N or X

Eject the MD EJECT Z after stopping

recording

When you pause recording

The track number increases by one. For example, if you

paused recording while recording track 4, the track

number will be 5 when you resume recording.

Bottom side of the MD

To prevent accidental erasure of the recorded

material

To make it impossible to record on an MD, slide the

record-protect tab in the direction of the arrow (see

illustration below) to open the slot. To enable recording,

close the slot.

z

To play the tracks you just recorded

Press N immediately after stopping recording.

The deck starts to play from the first track of the material just

recorded.

z

To play from the first track of the MD after recording

1 Press x again after stopping recording.

2 Press N.

The deck starts to play from the first track of the MD.

Note

You can’t record over existing material when Shuffle Play (page

24) or Program Play (page 25) has been selected. “Impossible”

appears in the display at this time.

Slide in the direction

of arrow

Record-protect tab

16

GB

Recording on MDs

Adjusting the Recording

Level

Do the procedure below to adjust the recording level.

LEVEL/DISPLAY/CHAR

AMS

` / 1

N

zxX

Z

>.

mM

1 Do steps 1 to 10 of “Recording on an MD” on pages

14 and 15.

2 Play the portion of the program source with the

strongest output.

3 Press LEVEL/DISPLAY/CHAR (or DISPLAY) repeatedly

until the peak level meters appear.

4 While monitoring the sound, turn AMS (or press

./> repeatedly) to raise the recording level to

its highest level without turning on “OVER” on the

peak level meters.

Occasional lighting of “OVER” is acceptable.

Avoid turning this indication on.

5 Stop playing the program source.

6 To start recording, continue from step 12 of

“Recording on an MD” on page 15.

z

You can adjust the recording level using the remote Z

During recording or recording pause, press LEVEL +/–

repeatedly.

z

To display the level of the strongest signal

The Peak Hold function continuously displays the level of the

strongest signal that has been input.

Do the procedure below to turn Peak Hold on.

1 While the deck is stopped, press MENU/NO twice to display

“Setup Menu.”

2 Turn AMS (or press ./> repeatedly) until “P.Hold”

appears, then press AMS or YES.

3 Turn AMS (or press ./> repeatedly) to select “P.Hold

On,” then press AMS or YES.

4 Press MENU/NO.

To turn Peak Hold off, repeat the procedure above, selecting

“P.Hold Off” in step 3.

Recording Tips

LEVEL/DISPLAY/CHAR

INPUT AMS YES

EJECT Z

MENU/NO

z

` / 1

N

zxX

Z

>.

mM

Checking the remaining recordable time

on the MD

Press LEVEL/DISPLAY/CHAR (or DISPLAY) repeatedly.

While the deck is The following information appears

Stopped Total number of tracks and total recorded

time t Remaining recordable time on

the MD t Disc name

Recording Recorded time of the current track t

Remaining recordable time on the MD t

Input level indication t Track name

For details, see page 12.

Monitoring the input signal

(Input Monitor)

You can monitor the selected input signal even when

you’re not recording it.

1 Press EJECT Z to eject the MD.

2 Set INPUT to the position that corresponds to the

jacks (connector) where the signal you want to

monitor is being input.

3 Press z.

When INPUT is set to ANALOG

The analog signal input from the LINE (ANALOG) IN

jacks is output to the LINE (ANALOG) OUT jacks

after A/D and D/A conversions. “AD - DA” appears

in the display at this time.

When INPUT is set to DIGITAL

The digital signal input from the DIGITAL IN

connector first passes through the sampling rate

converter, and then output to the LINE (ANALOG)

OUT jacks after D/A conversion. “- DA” appears in

the display at this time.

To stop monitoring the signal

Press x.

17

GB

Recording on MDs

Erasing blank portions automatically

(Smart Space/Auto Cut)

The deck can be set to automatically erase any blanks that

are produced when the signal is interrupted during

recording. The function which activates (Smart Space or

Auto Cut) depends on the length of the interruption, as

described below.

Smart Space

If the signal is interrupted for less than 30 seconds, Smart

Space replaces the blank portion with a blank space of

about three seconds, then continues the recording. “Smart

Space” appears in the display during this time.

Auto Cut

If the signal is interrupted for about 30 seconds , Auto Cut

replaces the blank portion with a blank space of about

three seconds, then pauses the recording. “Auto Cut”

appears in the display during this time.

Do the procedure below to turn Smart Space and Auto

Cut on or off.

1 While the deck is stopped, press MENU/NO twice.

“Setup Menu” appears in the display.

2 Turn AMS (or press ./> repeatedly) until

“S.Space” appears, then press AMS or YES.

3 Turn AMS (or press ./> repeatedly) to select

the setting, then press AMS or YES.

To Select

Turn on Smart Space and Auto Cut S.Space On (factory

setting)

Turn off Smart Space and Auto Cut S.Space Off

4 Press MENU/NO.

Notes

• If you start recording with no signal input, Smart Space and

Auto Cut will not operate regardless of the setting.

• Smart Space does not affect the order of the track numbers

being recorded, even if the blank space occurs in the middle of

a track.

• Auto Cut is automatically turned on or off in tandem with

Smart Space.

• If you turn off the deck or disconnect the AC power cord, the

deck will store the last setting (“S.Space On” or “S.Space Off”)

and apply it the next time you turn on the deck.

Marking Track Numbers

While Recording (Track Marking)

You can mark track numbers either manually or

automatically while recording. By marking track

numbers at specific points, you can quickly locate the

points later or edit the MD easily.

AMS YESMENU/NO

z

` / 1

N

zxX

Z

>.

mM

Marking track numbers manually

(Manual Track Marking)

Press z at the point where you want to add a track

number while recording.

Marking track numbers automatically

(Automatic Track Marking)

When recording from a CD player or MD deck connected

to the DIGITAL IN connector, the deck marks track

numbers in the same sequence as the source. When

recording from other sources connected to the DIGITAL

IN connector or a source connected to the LINE

(ANALOG) IN jacks, do the procedure below to mark

track numbers automatically.

1 While the deck is stopped, press MENU/NO twice.

“Setup Menu” appears in the display.

2 Turn AMS (or press ./> repeatedly) until

“T.Mark” appears, then press AMS or YES.

3 Turn AMS (or press ./> repeatedly) to select

the setting, then press AMS or YES.

To Select

Turn on Automatic Track Marking T.Mark LSync (factory

setting)

Turn off Automatic Track Marking T.Mark Off

4 Press MENU/NO.

The deck marks a track number whenever the input

signal level drops to –50 dB (the trigger level for

Automatic Track Marking) or below for at least 1.5

seconds.

18

GB

Recording on MDs

To change the trigger level for Automatic Track

Marking

Do the procedure below to change the signal level that

triggers Automatic Track Marking.

1 While the deck is stopped, press MENU/NO twice.

“Setup Menu” appears in the display.

2 Turn AMS (or press ./> repeatedly) until

“LS(T)” appears, then press AMS or YES.

3 Turn AMS (or press ./> repeatedly) to select

the level, then press AMS or YES.

You can set the level at any value between –72 dB and

0 dB, in 2 dB steps.

4 Press MENU/NO.

z

Additional information on Automatic Track Marking

• When recording from a CD player or MD deck connected to the

DIGITAL IN connector, the entire material may be recorded as

a single track in the following cases:

— When you consecutively record the same track two or more

time using single-track repeat play.

— When you consecutively record two or more tracks with the

same track number but from different CDs or MDs.

— When you record tracks from certain CD or multi-disc

players.

Also, if the source is an MD, a track number may not be

marked for tracks less than four seconds long.

• When recording from a component connected to the LINE

(ANALOG) IN jacks with “T.Mark Off” selected or when

recording from a DAT deck or DBS tuner connected to the

DIGITAL IN connector, the entire material may be recorded as

a single track.

• When recording from a DAT deck or DBS tuner connected to

the DIGITAL IN connector, the deck will mark a track number

whenever the sampling frequency of the input signal changes,

regardless of the track marking parameter setting (“T.Mark

LSync” or “ T.Mark Off”).

z

You can mark track numbers even after recording has

finished

See “Dividing Tracks” on page 31.

Note

If you turn off the deck or disconnect the AC power cord, the

deck will store the last settings (“T.Mark LSync” or “ T.Mark Off”

and the trigger level) and apply them the next time you turn on

the deck.

Starting Recording With Six

Seconds of Prestored Audio

Data (Time Machine Recording)

Whenever the deck is in recording pause, the deck’s

buffer memory continuously stores the latest six seconds

worth of audio data. When you press AMS (or T.REC),

the recording then starts with the data in the buffer

memory. Time Machine Recording thus allows you to

avoid missing the beginning of material recorded live

from an FM or satellite broadcast.

AMS

` / 1

N

zxX

Z

>.

mM

1 Do steps 1 to 10 of “Recording on an MD” on pages

14 and 15.

The deck changes to recording pause.

2 Start playing the program source.

3 Press AMS (or T.REC) at the point where you want

to start recording.

Recording starts with the six seconds of prestored data

in the buffer memory, then continues recording via the

buffer memory thereafter.

To stop Time Machine Recording

Press x.

Note

The storage of data in the buffer memory starts from the moment

the deck changes to recording pause. Thus, if you start recording

less than six seconds after changing to recording pause, less than

six seconds worth of data will be recorded from the buffer

memory. The same is true if the program source had been

playing for less than six seconds at the time you start recording.

Marking Track Numbers While Recording

(Track Marking)

19

GB

Recording on MDs

Synchro-recording With the

Audio Component of Your

Choice (Music Synchro-recording)

Z

The Music Synchro-recording allows you to automatically

synchronize recording on the MD deck with the playing

of the selected program source. The Track Marking

function, however, will differ according to the program

source. For details, see “Marking Track Numbers While

Recording” on page 17.

MUSIC SYNC

. >

m M

z x

X

H

Z

` / 1

+

–

>.X

1 Do steps 1 to 9 of “Recording on an MD” on pages

14 and 15.

2 Press MUSIC SYNC.

The deck changes to recording pause.

3 Start playing the program source.

Recording starts automatically.

To stop Music Synchro-recording

Press x.

Note

During Music Synchro-recording, Smart Space and Auto Cut will

operate regardless of their setting (“S.Space On” or “S.Space

Off”).

Synchro-recording With a

Sony CD Player

(CD Synchro-recording) Z

When the deck is connected to a Sony CD player or Hi-Fi

component system, you can easily copy the contents of

CDs to the MD using the deck’s remote. As the same

remote operates both the MD deck and the CD player or

CD player section of the component system, make sure to

place the MD deck and the CD player as close together as

possible.

Note

On some CD players and Hi-Fi component systems, you may

find it impossible to perform CD Synchro-recording using the

deck’s remote. In this case, use Music Synchro-recording (this

page) to record from CDs to the MD.

CD-SYNC STANDBY

CD-SYNC START

CD PLAYER ./

>

CD-SYNC STOP

DISPLAY

CD PLAYER X

. >

m M

z x

X

H

Z

` / 1

+

–

>.X

1 Turn on the amplifier and the CD player, and select

CD on the amplifier.

2 Do steps 2 to 9 of “Recording on an MD” on pages

14 and 15.

3 Insert a CD into the CD player and select the

playback mode (shuffle play, program play, etc.) on

the CD player.

4 Press CD-SYNC STANDBY.

The CD player changes to play standby and the MD

deck changes to recording standby.

5 Press CD-SYNC START.

The deck starts recording and the CD player starts to

play.

The track number and elapsed recording time of the

track appear in the display.

If the CD player doesn’t start playing

Some CD players may not respond when you press

CD-SYNC START. Press X on the CD player’s remote

instead to start play on the CD player.

20

GB

Recording on MDs

Operations you may want to do during CD

Synchro-recording

To Press

Stop recording CD-SYNC STOP

Pause recording CD-SYNC STANDBY or CD

PLAYER X

Locate the next track to be

recorded during recording

pause

CD PLAYER ./>

Resume recording after

pausing

CD-SYNC START or CD PLAYER

X

Check the remaining

recordable time on the MD

DISPLAY (page 12)

z

You can use the remote of the CD player during CD Synchro-

recording

Press To change the deck to And change the CD player to

H Recording Play

x Recording pause Stop

X Recording pause Pause

z

During CD Synchro-recording, track numbers are marked in

the following ways:

• When the CD player is connected to the DIGITAL IN connector,

track numbers are automatically marked as they appear on the

CD.

• When the CD player is connected to the LINE (ANALOG) IN

jacks, track numbers are automatically marked when “T.Mark

LSync” has been selected (page 17).

• When you resume recording after recording pause, a new track

number is automatically marked, regardless of the track

marking parameter setting (“T.Mark LSync” or “ T.Mark Off”).

z

You can change CDs during CD Synchro-recording

1 Press x on the CD player’s remote.

2 Change the CD.

3 Press H on the CD player’s remote.

Recording resumes.

z

You can also perform synchro-recording with a Sony video

CD player

By reprogramming the MD deck’s remote, you can use the

procedure above to perform Synchro-recording with a Sony

video CD player.

Press number button 2 while pressing down ~/1 on the MD

deck’s remote. You can now operate the MD deck and the video

CD player with the remote. To control the CD player again, press

number button 2 while pressing down ~/1 on the MD deck’s

remote.

Notes

• When performing CD Synchro-recording with a CD player

with a mode selector, be sure to set the selector to CD1.

• When you record tracks from certain CD or multi-disc players,

the entire material may be recorded as a single track.

Synchro-recording With a Sony CD Player

(CD Synchro-recording)

Страница загружается ...

Sony MDS-S40 Инструкция по применению

Sony MDS-S40 Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов