McQuay E Series Инструкция по установке

INVERTER CEILING CASSETTE

SPLIT TYPE AIR CONDITIONER

(E Series)

INSTALLATION MANUAL

IM-5CKYER-1009(1)-McQuay

Part Number: R08019034195A

IM-5CKYER-1009(1)-COVER_MC(EN).i1 1IM-5CKYER-1009(1)-COVER_MC(EN).i1 1 4/8/11 5:36:59 PM4/8/11 5:36:59 PM

IM-5CKYER-1009(1)-COVER_MC(EN).i2 2IM-5CKYER-1009(1)-COVER_MC(EN).i2 2 4/8/11 5:37:00 PM4/8/11 5:37:00 PM

1-1

English

Indoor Unit 5CKY20/25E/ER & 5CKY28/40/50ER

A

B

C

D

E

F

H

K

J

I

G

Original Instruction

All dimensions are in mm

OUTLINE AND DIMENSIONS

Dimension

Model

AB C D E F GH I J K

5CKY20/25E/ER

5CKY28ER

820 820 340 300 40 990 990 627 627 607 430

5CKY40/50ER 820 820 375 335 40 990 990 627 627 607 430

Outdoor Unit 5SLY20/25C/CR

All dimensions are in mm

N

L

KL

TN

M

A

D

O

PBQ

RS

C

HG

FE

IJ

Dimension

Model

ABCDEFGHI JKLMNOPQRST

5SLY20/25C/CR 855 730 328 513 182 44 93 149 101 113 603 126 164 15 47 3 23 73 75 362

1 EN 5CKYER-1009(1).indd 11 EN 5CKYER-1009(1).indd 1 4/21/11 9:11:09 AM4/21/11 9:11:09 AM

1-2

Outdoor Unit 5SLY28CR

A

D

K

E

S

T

S

T

GRR

OMN

H

P

Q

L

C

FU

J

B

I

Dimension

Model

ABCDEFGHI JKLMNOPQRSTU

5SLY28CR 940 348 753 855 392 733 603 328 303 370 362 448 190 80 58 180 32 126 32 15 23

1 EN 5CKYER-1009(1).indd 21 EN 5CKYER-1009(1).indd 2 4/21/11 9:11:13 AM4/21/11 9:11:13 AM

1-3

English

Outdoor Unit 5SLY40/50FR

AB AC AD

AE

AFAG

AH

AI

AA

AJ

AK

A

C

B

D

F

E

L

M

KJ

NO

Q

P

R

S

T

U

V

W

Z

X

Y

AT

AS

H

G

AU

AP

AQ

AO

AL

AM

AN

Dimension

Model

ABCDEFGHI JKLMN

5SLY40/50FR

900 1374 30 24 60 89 142 89 19 54 95 423 430 95

OPQRSTUVWXYZ

54 19 89 145 84 55 55 223 148 13 52 67

AA AB AC AD AE AF AG AH AI AJ AK AL AM AN

350 140 620 140 30 320 30 59 43 40 94 117 102 70

AO AP AQ AR AS AT AU

45 376 191 70 58 16 16

All dimensions are in mm

AR

I

1 EN 5CKYER-1009(1).indd 31 EN 5CKYER-1009(1).indd 3 4/21/11 9:11:13 AM4/21/11 9:11:13 AM

1-4

SAFETY PRECAUTIONS

! WARNING ! CAUTION

•

Installation and maintenance should be performed by qualiﬁ ed

persons who are familiar with local code and regulation, and

experienced with this type of appliance.

•

All ﬁ eld wiring must be installed in accordance with the national

wiring regulation.

•

Ensure that the rated voltage of the unit corresponds to that of

the name plate before commencing wiring work according to

the wiring diagram.

•

The unit must be GROUNDED to prevent possible hazard due

to insulation failure.

•

All electrical wiring must not touch the refrigerant piping, or

any moving parts of the fan motors.

•

Conﬁ rm that the unit has been switched OFF before installing

or servicing the unit.

•

Disconnect from the main power supply before servicing the

air conditioner unit.

•

DO NOT pull out the power cord when the power is ON. This

may cause serious electrical shocks which may result in ﬁ re

hazards.

•

Keep the indoor and outdoor units, power cable and transmission

wiring, at least 1m from TVs and radios, to prevent distorted

pictures and static. {Depending on the type and source of the

electrical waves, static may be heard even when more than 1m

away}.

Please take note of the following important points when

installing.

•

Do not install the unit where leakage of ﬂ ammable gas may

occur.

If gas leaks and accumulates around the unit, it may cause

ﬁ re ignition.

•

Ensure that drainage piping is connected properly.

If the drainage piping is not connected properly, it may

cause water leakage which will dampen the furniture.

•

Do not overcharge the unit.

This unit is factory pre-charged.

Overcharge will cause over-current or damage to the

compressor.

•

Ensure that the unitʼs panel is closed after service or

installation.

Unsecured panels will cause the unit to operate noisily.

•

Sharp edges and coil surfaces are potential locations which

may cause injury hazards.

Avoid from being in contact with these places.

•

Before turning off the power supply, set the remote

controllerʼs ON/OFF switch to the “OFF” position to

prevent the nuisance tripping of the unit. If this is not done,

the unitʼs fans will start turning automatically when power

resumes, posing a hazard to service personnel or the user.

•

Do not operate any heating apparatus too close to the air

conditioner unit. This may cause the plastic panel to melt or

deform as a result of the excessive heat.

•

Do not install the units at or near doorway.

•

Do not operate any heating apparatus too close to the air

conditioner unit or use in room where mineral oil, oil vapour

or oil steam exist, this may cause plastic part to melt or

deform as a result of excessive heat or chemical reaction.

•

When the unit is used in kitchen, keep ﬂ our away from going

into suction of the unit.

•

This unit is not suitable for factory used where cutting oil

mist or iron powder exist or voltage ﬂ uctuates greatly.

•

Do not install the units at area like hot spring or oil reﬁ nery

plant where sulphide gas exists.

•

Ensure the color of wires of the outdoor unit and the

terminal markings are same to the indoors

respectively.

•

IMPORTANT: DO NOT INSTALL OR USE THE AIR

CONDITIONER UNIT IN A LAUNDRY ROOM.

•

Donʼt use joined and twisted wires for incoming power

supply.

•

Avoid direct contact of any coil treatment cleaners on plastic

part. This may cause plastic part to deform as a result of

chemical reaction.

•

For any enquiries on spare parts please contact your

authorized dealer.

•

The equipment is not intended for use in a potentially

explosive atmosphere.

This manual provides the procedures of installation to ensure a safe and good standard of operation for the air conditioner unit.

Special adjustment may be necessary to suit local requirements.

Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.

This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for commercial use by lay persons.

INSTALLATION MANUAL

NOTICE

Disposal requirements

Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall not be mixed with unsorted

household waste.

Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the refrigerant, of oil and of other parts

must be done by a qualiﬁ ed installer in accordance with relevant local and national legislation.

Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By ensuring this product is disposed of

correctly, you will help to prevent potential negative consequences for the environment and human health. Please contact the installer or local

authority for more information.

Batteries must be removed from the remote controller and disposed of separately in accordance with relevant local and national legislation.

1 EN 5CKYER-1009(1).indd 41 EN 5CKYER-1009(1).indd 4 4/21/11 9:11:17 AM4/21/11 9:11:17 AM

1-5

English

IMPORTANT

Important information regarding the refrigerant used

This product contains ﬂ uorinated greenhouse gases covered by the Kyoto Protocol.

Do not vent gases into the atmosphere.

Refrigerant type: R410A

GWP

(1)

value: 1975

(1)

GWP = global warming potential

Please ﬁ ll in with indelible ink,

n 1 the factory refrigerant charge of the product,

n 2 the additional refrigerant amount charged in the ﬁ eld and

n 1 + 2 the total refrigerant charge

on the refrigerant charge label supplied with the product.

The ﬁ lled out label must be adhered in the proximity of the product charging port (e.g. onto the inside of the service cover).

1 factory refrigerant charge of the product:

see unit name plate

(2)

2 additional refrigerant amount charged in the ﬁ eld

3 total refrigerant charge

4 contains ﬂ uorinated greenhouse gases covered by the Kyoto Protocol

5 outdoor unit

6 refrigerant cylinder and manifold for charging

(2)

In case of multiple indoor systems, only 1 label must be adhered*, mentioning the total factory refrigerant charge of all

indoor units connected in the refrigerant system.

Periodical inspections for refrigerant leaks may be required depending on European or local legislation. Please contact your

local dealer for more information.

* on the outdoor unit

1 EN 5CKYER-1009(1).indd 51 EN 5CKYER-1009(1).indd 5 4/21/11 9:11:18 AM4/21/11 9:11:18 AM

1-6

INSTALLATION DIAGRAM

Drain Piping

Front Panel

Air Filter

(behind the grille)

Air Intake Grille

Air Discharge

Air Discharge Louver

Air Intake

Thermal Insulation

Wrap the insulated pipe with the

ﬁ nishing tape from bottom to top

Indoor Unit

Outdoor Unit

1 EN 5CKYER-1009(1).indd 61 EN 5CKYER-1009(1).indd 6 4/21/11 9:11:18 AM4/21/11 9:11:18 AM

1-7

English

Obstacle

1m or more

3m or more

Floor

0.5m or more 0.5m or more 0.5m or more

0.3m or less

Beam

990.0mm

30 mm

Indoor Unit

Ceiling

Board

NOTE

Be sure to discuss the ceiling drilling work with the installers

concerned.

• Measure and mark the position for the hanging rod. Drill

the hole for the angle nut on the ceiling and ﬁ x the hanging

rod.

• The installation template is extended according to

temperature and humidity. Check on dimensions in use.

• The dimensions of the installation template are the same as

those of the ceiling opening dimensions.

• Before ceiling laminating work is completed, be sure to ﬁ t

the installation template to the indoor unit.

• Conﬁ rm the pitch of the hanging rod is 770mm  622mm

sharp.

• Hold the unit and hang it on the hanging rod with the nut

and washer.

• Adjust the unit height to 30 mm between the indoor unit

bottom surface and the ceiling surface.

• Confirm with a level gauge that the unit is installed

horizontally and tighten the nut and bolt to prevent unit

falling and vibration.

• Open the ceiling board along the outer edge of the paper

installation template.

Unit Hanging

Unit Installation

INSTALLATION OF THE INDOOR UNIT

Preliminary Site Survey

Be sure to read this manual before installing the air-conditioner indoor unit.

• Voltage supply ﬂ uctuation must not exceed ±10% of rated voltage. Electricity supply lines must be independent of welding

transformers which can cause high supply ﬂ uctuation.

• Ensure that the location is convenient for wiring, piping and drainage.

• Do not exert pressure on the resin parts when opening the unit or when moving it after opening.

• Do not move the unit from packaging while moving, until it reaches the installation site. Use safe material or protection

plates when unpacking it or lifting it to avoid damage or scratches to the unit.

880.0~990.0mm (Ceiling Opening Site = 890mm)

770.0mm (Hanging Rod)

880.0~990.0mm (Ceiling Opening Site)

Piping Direction

622.0mm (Hanging Rod)

• Ensure a location where:

a) Drainage can be done easily.

b) Convenient for wiring and piping.

c) Which have enough space for installation and service work.

d) Where no risk of ﬂ ammable gas leakage.

e) When free from any obstacles in path of cool air discharge and warm air return and must allow spreading of air throughout

the room (near the center of the room).

f) Must be provided clearance for indoor unit from the wall and obstacles as shown in ﬁ gure below.

g) The installation place must be strong enough to support a load 4 times the indoor unit weight to avoid amplifying noise

and vibration.

h) The installation place (hanging ceiling surface) must be assuring levelness and the height in the ceiling is 350mm or

more.

i) The indoor unit must be away from heat and steam sources (avoid installing it near an entrance).

990.0mm

1 EN 5CKYER-1009(1).indd 71 EN 5CKYER-1009(1).indd 7 4/21/11 9:11:18 AM4/21/11 9:11:18 AM

1-8

Open

Screw

From

Unit

Control

Box

From

Front

Panel

LED Wire

Air Swing Wire

•

The front panel can only be ﬁ tted in one direction, follow the piping direction. (Follow piping arrow sticker on front panel)

• Be sure to remove the installation template before installing the front panel.

Panel Installation

• Open the air intake grille by pulling back the catchers and removing it together with ﬁ lter from panel.

• Install the front frame panel onto the indoor unit by 4 screws and tighten it completely to prevent cool air leakage.

• Connect the LED wire and air swing wire to the indoor unit.

• The air swing connector must put inside the control box after connected.

NOTE

This Indoor Unit uses a drain pump for condensed water drainage. Install the unit horizontally to prevent water leakage

or condensation around the air outlet.

Indoor Unit

Pipe Clamp

Feed Water

Flexible Drain Hose

Main Drain Pipe

•

Drain pipe must be in downward gradient for smooth

drainage.

•

Avoid installing the drain pipe in up and down slope to

prevent reversed water ﬂ ow.

•

During the drain pipe connection, be careful not to exert

extra force on the drain connector at indoor unit.

•

The outside diameter of the drain connection at the

ﬂ exible drain hose is 20 mm.

•

Be sure to execute heat insulation (polyethylene foam

with thickness more than 8.0 mm) on the drain piping to

avoid the condensed water dripping inside the room.

• Connect the main drain pipe to the ﬂ exible drain.

• Feed water from ﬂ exible drain hose to check the piping

for leakage.

• When the test is completed, connect the ﬂ exible drain

hose to the drain connector on the indoor unit.

Drain Pump Work

Drain Test

1 EN 5CKYER-1009(1).indd 81 EN 5CKYER-1009(1).indd 8 4/21/11 9:11:19 AM4/21/11 9:11:19 AM

1-9

English

Frame

Intake Grille

Cover Lock Grille

(2pcs)

Screw M4 x 6

(2pcs)

Cover Lock Grille (The moving part protection for user direct touching)

Cover lock grill must be installed as the ﬁ gure below.

If the unit need to be service, steps below shall be followed:

1. Conﬁ rm that the unit had been switched off before servicing the unit.

2. Use screwdriver to unlock the screw on the cover lock grille.

3. Remove the cover lock grille and open the intake grille for the service purpose.

4. Install the intake grille and screw the cover lock grille after service and make sure the unit is proper install.

1 EN 5CKYER-1009(1).indd 91 EN 5CKYER-1009(1).indd 9 4/21/11 9:11:19 AM4/21/11 9:11:19 AM

1-10

Figure 2 Figure 3

Figure 4 Figure 5

Wires Installation

Figure 1 and Figure 2 shows the location of cover wire in CKE unit.

Steps to install power supply wires and wires from outdoor unit.

1. Remove wire cover by removing 2 screws as shown in Figure 3.

2. Wires will go through the hole as shown in Figure 4 and 5 respectively without crossing the height of the hole.

3. After that, wire cover will be assembled back to close the wire.

Figure 1

! CAUTION

Do not install the unit at altitude over 2000m for both indoor and outdoor.

1 EN 5CKYER-1009(1).indd 101 EN 5CKYER-1009(1).indd 10 4/21/11 9:11:19 AM4/21/11 9:11:19 AM

1-11

English

• The outdoor unit must be installed in such a way, so as to prevent short circuit of the hot discharged air or obstruction to

the smooth air ﬂ ow. Please follow the installation clearance shown in the ﬁ gures below. Select the coolest possible place

where intake air temperature is not greater than the outside air temperature.

• Where a wall or other obstacles is in the path of outdoor unitʼs intake or exhaust airﬂ ow, follow the installation guidelines

below.

• For any of the below installation patterns, the wall height on the exhaust side should be 1200mm or less.

5SLY20/25C/CR

More than 50 More than 100

Side View

Top View

More than 50

More than 150

More than 100

More than 150

More than 300

Unit: mm

INSTALLATION OF THE OUTDOOR UNIT

Wall facing one side

More than 100 More than 350

More than 50

Top View

Side View

More

than 100

More than 350

More than 100

More than 350

Unit: mm

5SLY28CR

1200

or less

More than 50

Wall facing two sides

Wall facing one side Wall facing two sides

Wall facing three sides

1 EN 5CKYER-1009(1).indd 111 EN 5CKYER-1009(1).indd 11 4/21/11 9:11:19 AM4/21/11 9:11:19 AM

1-12

5SLY40/50FR

More than 100 More than 500

More

than 100

More

than

100

More than 100

More than 500

• Allow more space for installation above with additional obstacle at top side and installation in series.

Top View

Side View

Unit: mm

REFRIGERANT PIPING

Indoor 5CKY20E/ER 5CKY25E/ER 5CKY28ER

Outdoor 5SLY20C/CR 5SLY25C/CR 5SLY28CR

Max. allowable length, m 30 30 50

Max. allowable elevation, m 10 10 30

Liquid pipe size, mm/(in) 6.35 (1/4") 6.35 (1/4") 9.52 (3/8")

Gas pipe size, mm/(in) 12.70 (1/2") 15.88 (5/8") 15.88 (5/8")

Additional charge of refrigerant, g/m

(for piping length above 7.5m)

20 20 50

Indoor 5CKY40ER 5CKY50ER

Outdoor 5SLY40FR 5SLY50FR

Max. allowable length, m 75 75

Max. allowable elevation, m 30 30

Liquid pipe size, mm/(in) 9.52 (3/8") 9.52 (3/8")

Gas pipe size, mm/(in) 15.88 (5/8") 15.88 (5/8")

Additional charge of refrigerant, g/m

(for piping length above 30m)

50 50

Allowable Piping Length

When the pipe length becomes too long, both the capacity and reliability drop. As a result, compressor reliability will be

affected. Always choose the shortest path and follow the recommendation as tabulated below:

Wall facing one side

Wall facing more than 1 side of obstacle

1 EN 5CKYER-1009(1).indd 121 EN 5CKYER-1009(1).indd 12 4/21/11 9:11:20 AM4/21/11 9:11:20 AM

1-13

English

D

A

Piping Works And Flaring Technique

• Do not use contaminated or damaged copper tubing. If any pipings, evaporator or condenser had been exposed or had been

opened for 15 seconds or more, the system must be vacuumed. Generally, do not remove plastic, rubber plugs and brass

nuts from the valves, ﬁ ttings, tubings and coils until it is ready to connect suction or liquid line into valves or ﬁ ttings.

• If any brazing work is required, ensure that the nitrogen gas is passed through coil and joints while the brazing work is

being done. This will eliminate soot formation on the inside walls of the copper tubings.

• Cut the pipe stage by stage, advancing the blade of the pipe cutter slowly. Extra force and deep cut will cause more distortion

on the pipe and thus extra burr. See Figure A.

Cutting Copper Tube

Fig. B

Fig. A

Remove Burr

Fig. C

Copper Tube

Swaging Block

• Remove burrs from cut edges of the pipes with remover

as shown in Figure B. This will avoid unevenness on the

ﬂ are faces which will cause gas leak. Hold the pipe on

top position and burr remover at lower position to prevent

metal chips from entering the pipe.

• Insert the ﬂ are nuts, mounted on the connection parts of

both the indoor unit and outdoor unit, into the copper

pipes.

• The exact length of pipe protruding from the top surface of

the swaging block is determined by the ﬂ aring tool. Refer

Figure C.

• Fix the pipe ﬁ rmly on the swaging block. Match the centers

of both the ﬂ are die and the ﬂ aring punch, and then tighten

the ﬂ aring punch fully.

Piping Connection To The Units

• Align the center of the piping and tighten the ﬂ are nut

sufﬁ ciently with ﬁ ngers. Refer Figure D.

• Finally, tighten the ﬂ are nut with the torque wrench until

the wrench clicks.

• When tightening the ﬂ are nut with the torque wrench,

ensure that the tightening direction follows the arrow

indicated on the wrench.

• The refrigerant pipe connection are insulated by closed

cell polyurethane.

Spanar

Torque Wrench

Indoor Piping

Flare Nut

Flared Tube

Flare Joint

Fig. D

Ø Tube, D A (mm)

Inch mm Imperial

(Wing-nut Type)

Rigid

(Clutch Type)

1/4" 6.35 1.3 0.7

3/8" 9.52 1.6 1.0

1/2" 12.70 1.9 1.3

5/8" 15.88 2.2 1.7

3/4" 19.05 2.5 2.0

Pipe Size (mm/in) Torque (Nm/ft-lb)

6.35 (1/4) 18 (13.3)

9.52 (3/8) 42 (31.0)

12.70 (1/2) 55 (40.6)

15.88 (5/8) 65 (48.0)

19.05 (3/4) 78 (57.6)

1/4t

1 EN 5CKYER-1009(1).indd 131 EN 5CKYER-1009(1).indd 13 4/21/11 9:11:20 AM4/21/11 9:11:20 AM

1-14

Power Supply Cable

Outdoor Unit

Terminal Block

Indoor Unit

Terminal Block

L

N

SIG

2

1

SIG

2

1

5CKY20/25E/ER - 5SLY20/25C/CR

IMPORTANT: *

These values are for information only, they should be checked and selected to comply with the local and/or national

codes and regulations. They are also subjected to the type of installation and size of conductors used.

**

The appropriate voltage range should be checked with the label data on the unit.

Interconnection

Cable

ELECTRICAL CONNECTION

Model Indoor 5CKY20E/ER 5CKY25E/ER

Outdoor 5SLY20C/CR 5SLY25C/CR

Voltage range** Indoor

220V - 240V /1Ph /50Hz + !

Outdoor

220V - 240V /1Ph /50Hz + !

Power supply cable size* mm

2

Number of conductors

2.5

3

2.5

3

Interconnection cable size* mm

2

Number of conductors

2.5

4

2.5

4

Recommended time delay fuse* A 20 20

5CKY28ER - 5SLY28CR

Indoor Unit

Terminal Block

L

Interconnection

Cable

Model Indoor 5CKY28ER

Outdoor 5SLY28CR

Voltage range** Indoor

220V - 240V/1Ph/50Hz + !

Outdoor

220V - 240V/1Ph/50Hz + !

Power supply cable size* mm

2

Number of conductors

2.5

3

Interconnection cable size* mm

2

Number of conductors

1.5

4

Recommended time delay fuse* A 25

Power Supply Cable

There must be an all pole

disconnection in the supply

mains with a contact separation

of at least 3mm.

!

There must be an all pole

disconnection in the supply

mains with a contact separation

of at least 3mm.

!

Outdoor Unit

Terminal Block

N

SIG

N

L

N

L

1 EN 5CKYER-1009(1).indd 141 EN 5CKYER-1009(1).indd 14 4/21/11 9:11:21 AM4/21/11 9:11:21 AM

1-15

English

3

2

1

3

2

1

L1

L2

L3

N

Power Supply Cable

Outdoor Unit

Terminal Block

Indoor Unit

Terminal Block

5CKY40ER - 5SLY40FR (1 Phase)

5CKY50ER - 5SLY50FR (1 Phase)

3

2

1

2

1

3

L

N

Interconnection

Cable

Model Indoor 5CKY40ER 5CKY50ER

Outdoor 5SLY40FR 5SLY50FR

Voltage range** Indoor

220V - 240V/1Ph/50Hz + !

Outdoor

220V - 240V/1Ph/50Hz + !

Power supply cable size* mm

2

Number of conductors

6

3

6

3

Interconnection cable size* mm

2

Number of conductors

1.5

4

1.5

4

Recommended time delay fuse* A 32 32

5CKY40ER - 5SLY40FR (3 Phase)

5CKY50ER - 5SLY50FR (3 Phase)

There must be an all pole

disconnection in the supply

mains with a contact separation

of at least 3mm.

!

Model Indoor 5CKY40ER 5CKY50ER

Outdoor 5SLY40FR 5SLY50FR

Voltage range** Indoor

220V - 240V/1Ph/50Hz + !

Outdoor

380V - 415V/3N~/50Hz + !

Power supply cable size* mm

2

Number of conductors

4

5

4

5

Interconnection cable size* mm

2

Number of conductors

1.5

4

1.5

4

Recommended time delay fuse* A 20 20

Power Supply Cable

Indoor Unit

Terminal Block

Interconnection

Cable

Outdoor Unit

Terminal Block

There must be an all pole

disconnection in the supply

mains with a contact separation

of at least 3mm.

!

1 EN 5CKYER-1009(1).indd 151 EN 5CKYER-1009(1).indd 15 4/21/11 9:11:21 AM4/21/11 9:11:21 AM

1-16

Attach insulation sleeve

Round crimp-style terminal

Electric wire

Connect wires of the

same gauge to both side.

Do not connect wires of the

same gauge to one side.

Do not connect wires

of different gauges.

• All wires must be ﬁ rmly connected.

• Make sure all the wire do not touch the refrigerant pipings, compressor or any moving parts.

• The connecting wire between the indoor unit and the outdoor unit must be clamped by using provided cord anchorage.

• The power supply cord must be equivalent to H07RN-F which is the minimum requirement.

• Make sure no external pressure is applied to the terminal connectors and wires.

• Make sure all the covers are properly ﬁ xed to avoid any gap.

• Use round crimp-style terminal for connecting wires to the power supply terminal block. Connect the wires by matching

to the indication on terminal block. (Refer to the wiring diagram attached on the unit).

• Use the correct screwdriver for terminal screws tightening. Unsuitable screwdrivers can damage the screw head.

• Over tightening can damage the terminal screw.

• Do not connect wire of different gauge to same terminal.

• Keep wiring in an orderly manner. Prevent the wiring from obstructing other parts and the terminal box cover.

R410A is a new HFC refrigerant which does not damage the

ozone layer. The working pressure of this new refrigerant is 1.6

times higher than conventional refrigerant (R22), thus proper

installation / servicing is essential.

• Never use refrigerant other than R410A in an air conditioner

which designed to operate with R410A.

• POE or PVE oil is used as lubricant for R410A

compressor, which is different from the mineral oil used

for R22 compressor. During installation or servicing, extra

precaution must be taken not to expose the R410A system

too long to moist air. Residual POE or PVE oil in the piping

and components can absorb moisture from the air.

• To prevent mischarging, the diameter of the service port

on the ﬂ are valve is different from that of R22.

• Use tools and materials exclusively for refrigerant R410A.

Tools exclusively for R410A are manifold valve, charging

hose, pressure gauge, gas leak detector, ﬂ are tools, torque

wrench, vacuum pump and refrigerant cylinder.

• As an R410A air conditioner incurs higher pressure

than R22 units, it is essential to choose the copper pipes

correctly. Never use copper pipes thinner than 0.8mm even

though they are available in the market.

• If the refrigerant gas leakage occurs during installation /

servicing, be sure to ventilate fully. If the refrigerant gas

comes into contact with ﬁ re, a poisonous gas may occur.

• When installing or removing an air conditioner, do not

allow air or moisture to remain in the refrigerant cycle.

SPECIAL PRECAUTIONS WHEN DEALING WITH R410A UNIT

1 EN 5CKYER-1009(1).indd 161 EN 5CKYER-1009(1).indd 16 4/21/11 9:11:21 AM4/21/11 9:11:21 AM

1-17

English

Vacuuming is necessary to eliminate all moisture and air from the system. The series II Outdoor Unit is provided with ﬂ are

valve ﬁ ttings.

Vacuuming The Piping And The Indoor Unit

Except for the outdoor unit which is pre-charged with

refrigerant, the indoor unit and the refrigerant connection

pipes must be air-purged because the air containing moisture

that remains in the refrigerant cycle may cause malfunction

of the compressor.

• Remove the caps from the valve and the service port.

• Connect the center of the charging gauge to the vacuum

pump.

• Connect the charging gauge to the service port of the 3-way

valve.

• Start the vacuum pump. Evacuate for approximately 30

minutes. The evacuation time varies with different vacuum

pump capacity. Conﬁ rm that the charging gauge needle has

moved towards -760mmHg.

Caution

• If the gauge needle does not move to -760mmHg, be sure to

check for gas leaks (using the refrigerant detector) at ﬂ are

type connection of the indoor and outdoor unit and repair

the leak before proceeding to the next step.

• Close the valve of the changing gauge and stop the vacuum

pump.

• On the outdoor unit, open the suction valve (3 way) and

liquid valve (2 way) (in anti-clockwise direction) with 4mm

key for hexagon sacked screw.

Charge Operation

This operation must be done by using a gas cylinder and a

precise weighing machine. The additional charge is topped-up

into the outdoor unit using the suction valve via the service

port.

• Remove the service port cap.

• Connect the low pressure side of the charging gauge to the

suction service port center of the cylinder tank and close

the high pressure side of the gauge. Purge the air from the

service hose.

• Start the air conditioner unit.

• Open the gas cylinder and low pressure charging valve.

• When the required refrigerant quantity is pumped into

the unit, close the low pressure side and the gas cylinder

valve.

• Disconnect the service hose from service port. Put back the

service port cap.

VACUUMING AND CHARGING

Refrigerant Piping

Outdoor Unit 3 ways valve

Allen key

Service Port

Flare nut

HIGH PRESSURE GAUGE

GAUGE MANIFOLD

LOW PRESSURE GAUGE

HANDLE HI (ALWAYS CLOSED)

CHARGE HOSE

-760mmHg

HANDLE LO

CHARGE HOSE

VACUUM PUMP

ADAPTER FOR

COUNTER FLOW

PREVENTION

CHECK VALVE

LIQUID VALVE

HIGH PRESSURE GAUGE

LOW PRESSURE GAUGE

GAUGE MANIFOLD

-760mmHg

HANDLE LO

HANDLE HI (ALWAYS CLOSED)

CHARGE HOSE

CHECK VALVE

LIQUID VALVE

GAS VALVE

(3-WAY)

CONFIGURATION OF AIR

PURGE BY CHARGING

CONFIGURATION OF AIR

PURGE BY CHARGING

GAS VALVE

(3-WAY)

1 EN 5CKYER-1009(1).indd 171 EN 5CKYER-1009(1).indd 17 4/21/11 9:11:22 AM4/21/11 9:11:22 AM

1-18

Sealing Material

• It is possible to seal one of the four air discharge outlet. (sealing two or more air discharge outlet could cause a

malfunction)

• Remove the front panel and insert the sealing material into the air discharge outlet on the indoor unit to seal the air

outlet.

• The sealing material is the same length as the longer air discharge outlet. If it is desired to seal the shorter air discharge

outlet, cut the sealing material to shorten it.

• Push the sealing material in about 10 mm beyond the bottom surface of the indoor unit so that it does not touch the air

louver. Be sure not to push the sealing material in any farther than about 10mm.

Short Duct Speciﬁ cation

• The indoor unit is provided with air discharge and air intake “knock-out” hole for duct connection. However the connection

of the short duct for air discharge is possible on only one side.

• The use of short duct for air discharge will improve airﬂ ow distribution if there is an obstruction (such as a lighting ﬁ xture)

or in a long, narrow room or an L-shaped room. It also use for air conditioning of two rooms simultaneously.

Possible Opening Dimension For Duct Connection

Air Discharge Knock Out Hole

Air Intake Knock

Out Hole

Possible Direction For Air Discharge And Air Intake

Air Intake

Air DischargeAir Discharge

Air Discharge Air Discharge

10

50 50 50 50 50 10

207020

90

Ø100

PCD Ø140

115 20 115

ACCESSORY PARTS

NOTE

• Avoid using the short duct on which the air discharge grille can be completely closed, to prevent evaporator

freezing.

• In order to prevent condensation forming, be sure that there is sufﬁ cient thermal insulation and no leakage of cool

air when installing the short duct.

• Keep the introduction of fresh air intake within 20% of total air ﬂ ow. Also provide chamber and use booster fan.

1 EN 5CKYER-1009(1).indd 181 EN 5CKYER-1009(1).indd 18 4/21/11 9:11:22 AM4/21/11 9:11:22 AM

Страница загружается ...

McQuay E Series Инструкция по установке

McQuay E Series Инструкция по установке

на других языках

Похожие модели бренда

Модели других брендов