Acson 5CE 40E Инструкция по установке

CEILING/FLOOR

EXPOSED CONVERTIBLE

SPLIT TYPE AIR CONDITIONERS

CEILING EXPOSED

INSTALLATION MANUAL

IM-CEE-1108(0)-ACSON

Part No.: R08019032648

IM-CEE-1108(0) COVER-EN_AS 5/26/09, 3:24 PM3

1-1

English

OUTLINE AND DIMENSIONS

Indoor Unit

All dimensions are in mm/(in)

A

B

E

C

D

G

F

Outdoor Unit ((5)SL35/40C/CR)

All dimensions are in mm/(in)

Dimension A B C D E F G

(5)CE 35E/ER

1272 1088 74 1320 268 635 259

(50.1) (42.8) (2.9) (52.0) (10.6) (25.0) (10.2)

(5)CE 40E/ER

1490 1308 74 1538 268 635 259

(5.9) (51.5) (2.9) (60.6) (10.6) (25.0) (10.2)

1000.0 (39.4)

400.0 (15.7)

320.0 (12.6)

40.0

(1.6)

40.0

(1.6)

745.6 (29.4)

141.5 (5.6)

488.0 (19.2)

25.0 (1.0)

850.0 (33.5)

50.0

(2.0)

35.0

(1.4)

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM1

1-2

! CAUTION

Please take note of the following important points when

installing.

• Do not install the unit where leakage of flammable

gas may occur.

If gas leaks and accumulates around the unit, it

may cause fire ignition.

• Ensure that drainage piping is connected properly.

If the drainage piping is not connected properly, it

may cause water leakage which will dampen the

furniture.

• Do not overcharge the unit.

This unit is factory pre-charged.

Overcharge will cause over-current or damage to

the compressor.

• Ensure that the unit’s panel is closed after service or

installation.

Unsecured panels will cause the unit to operate

noisily.

• Sharp edges and coil surfaces are potential locations

which may cause injury hazards.

Avoid from being in contact with these places.

• Before turning off the power supply, set the remote

controller’s ON/OFF switch to the “OFF” position

to prevent the nuisance tripping of the unit. If this is

not done, the unit’s fans will start turning automatically

when power resumes, posing a hazard to service

personnel or the user.

• Do not operate any heating apparatus too close to

the air conditioner unit. This may cause the plastic

panel to melt or deform as a result of the excessive heat.

• Ensure the color of wires of the outdoor unit and the

terminal markings are same to the indoors

respectively.

• IMPORTANT : DO NOT INSTALL OR USE THE

AIR CONDITIONER UNIT IN A LAUNDRY

ROOM.

• Don’t use joined and twisted wires for incoming

power supply.

! WARNING

• Installation and maintenance should be performed by

qualified persons who are familiar with local code and

regulation, and experienced with this type of appliance.

• All field wiring must be installed in accordance with

the national wiring regulation.

• Ensure that the rated voltage of the unit corresponds to

that of the name plate before commencing wiring work

according to the wiring diagram.

• The unit must be GROUNDED to prevent possible

hazard due to insulation failure.

• All electrical wiring must not touch the refrigerant

piping, or any moving parts of the fan motors.

• Confirm that the unit has been switched OFF before

installing or servicing the unit.

• Disconnect from the main power supply before

servicing the air conditioner unit.

• DO NOT pull out the power cord when the power is

ON. This may cause serious electrical shocks which

may result in fire hazards.

• Keep the indoor and outdoor units, power cable and

transmission wiring, at least 1m from TVs and radios,

to prevent distorted pictures and static. {Depending on

the type and source of the electrical waves, static may

be heard even when more than 1m away}.

SAFETY PRECAUTIONS

This manual provides the procedures of installation to ensure a safe and good standard of operation for the air

conditioner unit.

Special adjustment may be necessary to suit local requirements.

Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.

INSTALLATION MANUAL

NOTICE

Disposal requirements

Your air conditioning product is marked with this symbol. This means that electrical and electronic products

shall not be mixed with unsorted household waste.

Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the

refrigerant, of oil and of other parts must be done by a qualified installer in accordance with relevant local and

national legislation.

Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By

ensuring this product is disposed of correctly, you will help to prevent potential negative consequences for

the environment and human health. Please contact the installer or local authority for more information.

Batteries must be removed from the remote controller and disposed of separately in accordance with relevant

local and national legislation.

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM2

1-3

English

Important information regarding the refrigerant used

This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. Do not vent gases into the atmosphere.

Refrigerant type: R410A

GWP

(1)

value: 1975

(1)

GWP = global warming potential

Please fill in with indelible ink,

 1 the factory refrigerant charge of the product,

 2 the additional refrigerant amount charged in the field and

 1 + 2 the total refrigerant charge

on the refrigerant charge label supplied with the product.

The filled out label must be adhered in the proximity of the product charging port (e.g. onto the inside of the service cover).

1 factory refrigerant charge of the product:

see unit name plate

(2)

2 additional refrigerant amount charged in the field

3 total refrigerant charge

4 Contains fluorinated greenhouse gases covered by the Kyoto Protocol

5 outdoor unit

6 refrigerant cylinder and manifold for charging

(2)

In case of multiple indoor systems, only 1 label must be adhered*, mentioning the total factory refrigerant charge of all

indoor units connected in the refrigerant system.

Periodical inspections for refrigerant leaks may be required depending on European or local legislation. Please contact your

local dealer for more information.

* on the outdoor unit

IMPORTANT

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM3

1-4

Dimension ABCDE F

(5)CE 35E/ER

1320 635 255 134 1222 49

(52.0) (25.0) (10.0) (5.3) (48.1) (1.9)

(5)CE 40E/ER

1538 635 255 134 1440 49

(60.6) (25.0) (10.0) (5.3) (56.7) (1.9)

Preliminary Site Survey

• Electrical supply and installation is to conform to local

authority’s (e.g. National Electrical Board) codes and

regulations.

• Voltage supply fluctuation must not exceed ±10% of

rated voltage. Electricity supply lines must be

independent of welding transformer which can cause

high supply fluctuations.

• Ensure that the location is convenient for wiring, piping

and drainage.

Standard Mounting

Ensure that the overhead supports are strong enough to hold the

weight of the unit. Position the hanger rods (wall mounting

bracket for floor standing), and check for its alignment with the

unit as shown in Figure A. Also, check that the hangers are

secured and the base of the fan coil unit is leveled in both

horizontal directions, taking into account the gradient for

drainage flow as recommended in Figure B.

INSTALLATION OF THE INDOOR UNIT

INSTALLATION DIAGRAM

Indoor Unit

Outdoor Unit

Refrigerant piping

Air Intake

Air Intake Nozzle

Air Discharge Louver

Signal Receiver

Indicator Lights

Air Intake Grille

Air Filters

(Inside Air Intake Grille)

Fig A

A

E

B

C

D

F

All dimensions are in mm/(in)

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM4

1-5

English

Fig B

10.0mm (0.39")

10.0mm (0.39") Lower

Please ensure that the following steps are taken:

• Check the gradient for drainage flow as recommended in Figure B.

• Provide clearance for easy servicing and optimal air flow as shown in Figure C.

• The indoor unit must be installed such that there is no short circuit of the cool discharge air with the warm return air.

• Do not install the indoor unit where there is direct sunlight shining on the unit. The location should be suitable for piping

and drainage installation. The unit must be a large distance away from the door.

Fig C

Ceiling Type

Floor Standing Type

Min. 10.0mm (0.39")

Max. 250mm (9.84")

Min. 500mm (19.60")

Utensils, Furnitures Or Built-

In Architectural Features

Must Not Protrude More

Than 250.0mm

Min. 1.0m (39.37")

Min. 400.0mm (15.75")

Min. 300.0mm (11.81")

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM5

1-6

10mm

300mm(Min.)

621mm

10mm

Ceiling

10mm

UNDER CEILING INSTALLATION

Install Suspension Bolts

1. Install the suspension bolts so that it can support the

indoor unit.

2. Adjust distance to ceiling before installation.

3. Refer to dimension given to install the unit.

Installation Ceiling Type

Installation Floor Type

Wall

Fig D

Fig E

Install Indoor Units

1. Insert the suspension bolts into the fittings of the hanger

bracket.

2. Set the nuts and washer on both side of the metal fittings.

3. Secure it with nuts.

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM6

1-7

English

Installation - Ceiling Exposed Type

Step 1

Remove air intake grille, side panel and hanger bracket from the unit. Please refer to Fig F.

Step 2

Position the hanger rod as shown in Fig G and install the hanger bracket.

Fig F

Fig G

Step 3

Hang up the unit and tighten the bolts after installation of piping and drain pipe.

Lastly install the intake grille and side panel to the correct position.

Fig H

Hanger Bracket

Side Panel

Intake grille

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM7

1-8

Fig I

Piping and Drain Hose Installation

Steps to open intake grille

1. Unlock the screw attached to block lock grille with screwdriver.

2. Remove block lock grille and unlock grille lock.

3. Please refer to Fig K for reference.

Block Lock Grille

Screw (M4)

Close

Open

Fig K

Drain Hose

Fig J

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM8

1-9

English

REFRIGERANT PIPING

• When the pipe length becomes too long, both the capacity and reliability drop. As the number of bends increases, system

piping resistance to the refrigerant flow increases, thus lowering the cooling capacity, and as the result the front compressor

may become defective. Always choose the shortest path and follow the recommendation as tabulated below:

Piping Sizes (Flare Connection Type)

Piping sizes are as follows:

• Do not use contaminated or damaged copper tubing. If

any piping, evaporator or condenser had been exposed or

had been opened for 15 seconds or more, then vacuum

and purge with field supplied refrigerant. Generally do not

remove plastic, rubber plug and brass nuts from the valves,

fittings, tubing and coils until it is ready to connect suction

or liquid line into valves or fittings.

• If any brazing work is required, ensure that nitrogen gas is

passed through coil and joints while the brazing work is

being done. This will eliminate soot formation on the inside

wall of copper tubings.

• Cut the pipe stages by stages, advancing the blade of pipe

cutter slowly. Extra force and a deep cut will cause more

distortion of pipe and therefore extra burr.

• Remove burrs from cut edges of pipes with a remover.

This will avoid unevenness on the flare face which will

cause gas leak.

• Align the center of the piping and sufficiently tighten the

flare nut with fingers. Finally, tighten the flare nut with

torque wrench until the wrench clicks.

• Be sure to execute heat insulation (polyurethane form with

thickness more than 15 mm).

• Except the outdoor unit which is pre-charge with refrigerant

R22, the indoor unit and the refrigerant connection pipes

must be purged because the air that contain moisture

remaining in the refrigerant cycle may cause malfunction

to the compressor.

Model

Indoor (5)CE 35E/ER (5)CE 40E/ER

Outdoor (5)SL35C/CR (5)SL40C/CR

Maximum Length (m)

45 45

Maximum Elevation (m)

25 25

Maximum No. of Bends

10 10

R22

R410

Model 5SL35C/CR 5SL40C/CR

Liquid (mm/in) 9.52 / 3/8 9.52 / 3/8

Suction (mm/in) 15.88 / 5/8 15.88 / 5/8

Maximum Pipe Length And Maximum Number Of Bends

Piping Connection

Piping Connection To The Units

• Align the center of the piping and tighten the flare nut

sufficiently with fingers.

• Finally, tighten the flare nut with torque wrench until

the wrench clicks.

• When tightening the flare nut with torque wrench, ensure

the direction for tightening follows the arrow on the

wrench.

Pipe Size (mm/in) Torque (Nm)

6.35 (1/4) 18

9.52 (3/8) 42

12.70 (1/2) 55

15.88 (5/8) 65

19.05 (3/4) 78

Flared TubeFlare Joint

Flare Nut

Indoor Piping

Torque Wrench

Spanar

Model SL35C/CR SL40C/CR

Liquid (mm/in) 9.52 / 3/8 9.52 / 3/8

Suction (mm/in) 19.05 / 3/4 19.05 / 3/4

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM9

1-10

ELECTRICAL WIRING CONNECTION

IMPORTANT: * These values are for information only. They should be checked and selected to comply with local and/or

national codes and regulations. They are also subject to the type of installation and size of conductors.

Model Indoor (5)CE35E (5)CE40E

Outdoor (5)SL35C (5)SL40C

Voltage range 220-240V/1Ph/50Hz +

!

Recommended fuse* (A) 30 30

Power supply cable size* (mm

2

) 44

Number of conductors 33

Interconnection cable size* (mm

2

) 1.5 1.5

Number of conductors 44

R

N

L

COMP

S

L

COMP

L

N

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral)

with minimum contact gap of 3.0mm.

(5)CE35/40E Vs (5)SL35/40C (1 PH)

Indoor Unit

Terminal

Block

Interconnection Cable

Outdoor Unit

Terminal

Block

!

Power Supply Cable

COMP

L

N

COMP

N

L

R

N

S

T

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral)

with minimum contact gap of 3.0mm.

(5)CE40E Vs (5)SL40C (3 PH)

5CE35E Vs 5SL35C (3 PH)

Indoor Unit

Terminal

Block

Interconnection Cable

Outdoor Unit

Terminal

Block

!

Power Supply Cable

Cooling Only

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM10

1-11

English

Model Indoor 5CE35E (5)CE40E

Outdoor 5SL35C (5)SL40C

Voltage range 380-415V/1Ph/50Hz +

!

Recommended fuse* (A) 10 13

Power supply cable size* (mm

2

) 1.5 2.5

Number of conductors 55

Interconnection cable size* (mm

2

) 1.5 1.5

Number of conductors 44

A

4WV

OF

N

L

COMP

A

4WV

OF

COMP

N

L

N

L

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral)

with minimum contact gap of 3.0mm.

(5)CE35/40ER Vs (5)SL35/40CR (1 PH)

Indoor Unit

Terminal

Block

Interconnection Cable

Outdoor Unit

Terminal

Block

!

Power Supply Cable

Outdoor Coil Sensor

Heat Pump Unit

Model Indoor (5)CE35ER (5)CE40ER

Outdoor (5)SL35CR (5)SL40CR

Voltage range 220-240V/1Ph/50Hz +

!

Recommended fuse* (A) 30 30

Power supply cable size* (mm

2

) 44

Number of conductors 33

Interconnection cable size* (mm

2

) 1.5 1.5

Number of conductors 3&4 3&4

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM11

1-12

• All wires must be firmly connected.

• Make sure all the wire not touching the refrigerant piping, compressor or any moving parts of the fan motor.

• The connecting wire between the indoor unit and the outdoor unit must be clamped on the wire clamps.

• The power supply cord must be equivalent to H07RN-F (245 IEC65, 245 IEC66) which is the minimum requirement.

• When attaching the terminal box lid, make sure do not pinch any wires.

• After all the wiring connections are done, fill in any gaps/holes with insulation (procured locally) to prevent small animals

and insects entering the unit from outside.

• Use round crimp-style terminal for connecting wires to the power supply terminal block. Connect the wires by matching to

the indication on terminal block. (Refer to the wiring diagram attached on the unit).

Model Indoor 5CE35ER (5)CE40ER

Outdoor 5SL35CR (5)SL40CR

Voltage range 380-415V/3Ph/50Hz +

!

Recommended fuse* (A) 10 13

Power supply cable size* (mm

2

) 1.5 2.5

Number of conductors 55

Interconnection cable size* (mm

2

) 1.5 1.5

Number of conductors 3&4 3&4

A

4WV

OF

COMP

A

R

S

T

4WV

OF

N

COMP

N

L

N

L

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral)

with minimum contact gap of 3.0mm.

(5)CE40ER Vs (5)SL40CR (3PH)

5CE35ER Vs 5SL35CR (3PH)

Indoor Unit

Terminal

Block

Interconnection

Cable

Outdoor Unit

Terminal

Block

!

Power Supply Cable

380-415V/3Ph/50Hz

Outdoor Coil Sensor

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM12

1-13

English

VACUUMING AND CHARGING

Purging The Piping And The Indoor Unit

Except for the outdoor unit which is pre-charged with

refrigerant, the indoor unit and the refrigerant connection

pipes must be air-purged because the air containing

moisture that remains in the refrigerant cycle may cause

malfunction of the compressor.

• Remove the caps from the valve and the service port.

• Connect the center of the charging gauge to the vacuum

pump.

• Connect the charging gauge to the service port of the

3-way valve.

• Start the vacuum pump. Evacuate for approximately 30

minutes. The evacuation time varies with different

vacuum pump capacity. Confirm that the charging gauge

needle has moved towards -76mmHg (0~76mmHg).

Vacuuming is necessary to eliminate all moisture and air

from the system. The series II Outdoor Unit is provided with

flare valve fittings.

Service Port

Outdoor Unit

3 Ways Valve

Flare Nut

Refrigerant Piping

Allen Key

Liquid Side

Indoor Unit

Outdoor Unit

Gas Side

Low

Hi

Vacuum

Pump

Open

Close

Discharge Valve

Suction Valve

Vacuuming for indoor unit

Before vacuuming, perform leak check for refrigeration

circuit. After the system piping are properly connected,

connect the flexible hoses to the correct charging nipples as

shown in the diagram. Ensure that flexible hose from

charging nipples are connected to the vacuum pump via

standard servicing valves and pressure gauges (gauge

manifold). Vacuum the air conditioner system to at least 500

microns Hg. Do not start the unit when the system is engaged

in vacuuming. The outdoor is pre-charge.

Caution

• If the gauge needle does not move to 0~76mmHg, be

sure to check for gas leaks (using the refrigerant

detector) at flare type connection of the indoor and

outdoor unit and repair the leak before proceeding to

the next step.

• Close the valve of the changing gauge and stop the

vacuum pump.

• On the outdoor unit, open the suction valve (3 way) and

liquid valve (2 way) (in anti-clockwise direction) with

4mm key for hexagon sacked screw.

Step to connect the installation wire:

• Used the correct screwdriver for tightening the terminal screws. If the block is too small, the mad of the screw might be

damaged and the screw will not be properly tightened. If tightening too hard, screw might be damaged.

• Do not connect wire at different gauge to the same proper supply terminal.

• Use specified electric wire. Connect the wire securely to the terminal. Lock the wire down without applying excessive

force to the terminal.

• Keep wiring in mat order and not to obstruct other equipment such as popping open the terminal box lid.

Attach insulation sleeve

Round crimp-style terminal

Electric wire

Connect wires of the

same gauge to both

side.

Do not connect wires

of the same gauge to

one side.

Do not connect wires

of different gauges.

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM13

1-14

Charge Operation

This operation must be done by using a gas cylinder and a precise weighing machine. The additional charge is topped-up

into the outdoor unit using the suction valve via the service port.

• Remove the service port cap.

• Connect the low pressure side of the charging gauge to the suction service port center of the cylinder tank and close the

high pressure side of the gauge. Purge the air from the service hose.

• Start the air conditioner unit.

• Open the gas cylinder and low pressure charging valve.

• When the required refrigerant quantity is pumped into the unit, close the low pressure side and the gas cylinder valve.

• Disconnect the service hose from service port. Put back the service port cap.

Suction Valve

Discharge Valve

Liquid Side

Indoor Unit

Outdoor Unit

Gas Side

Low

Hi

Open

Close

Open

Check

Valve

Indoor CE35E CE40E

Outdoor SL35C SL40C (1PH) SL40C (3PH)

Additional charge [g/m] 57 55 56

Additional Charge

The refrigerant is pre-charge in the outdoor unit. If the piping length is less than 7.5m, then additional charge after vacuuming

is not necessary. If the piping length is more than 7.5m then use the additional charge value as indicated in the table.

Additional refrigerant charge [g] per additional 1m length as tabulated (for R22 models)

Cooling only

Example:

CE35E & SL35C with 13m piping length, additional piping length is 5.5m. Thus,

Additional charge = 5.5[m] x 38[g/m]

= 209[g]

Additional refrigerant charge [g] per additional 1m length as tabulated (for R410A models)

Cooling only

Indoor 5CE35E 5CE40E

Outdoor 5SL35C

(1 PH)

5SL35C

(3 PH) 5SL40C (1 PH) 5SL40C (3 PH)

Additional charge [g/m] 27 27 24 25

Heat Pump Unit

Indoor CE35ER CE40ER

Outdoor SL35CR

SL40CR (1PH) SL40CR (3PH)

Additional charge [g/m] 54 54 55

Indoor 5CE35ER 5CE40ER

Outdoor 5SL35CR

(1 PH)

5SL35CR

(3 PH) 5SL40CR (1 PH) 5SL40CR (3 PH)

Additional charge [g/m] 28 27 39 39

Heat Pump Unit

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM14

1-15

English

SERVICE AND MAINTENANCE

Service Parts

Indoor Air

Filter

Indoor Unit

Maintenance Procedures

1. Remove any dust adhering to the filter by using a vacuum

cleaner or wash in lukewarm water (below 40°C) with a

neutral cleaning detergent.

2. Rinse the filter well and dry before placing it back onto

the unit.

3. Do not use gasoline, volatile substances or chemicals to

clean the filter.

1. Clean any dirt or dust on the grille or panel by wiping it

with a soft cloth soaked in lukewarm water (below 40°C)

and a neutral detergent solution.

2. Do not use gasoline, volatile substances or chemicals to

clean the indoor unit.

Period

At least once

every 2 weeks.

More frequently

if necessary.

At least once

every 2 weeks.

More frequently

if necessary.

Cooling

STANDARD OPERATING CONDITIONS

Outdoor

DB (°C)

46

43

19

14 19 23

Indoor WB (°C)

Cooling Operation Range

D

C

B

A

E

Appendix B: Operating Range for Air Cool Direct Expansion Unit

Heating

Outdoor

WB (°C)

18

15

Indoor DB (°C)

Heating Operation Range

J

I

G

F

10

-9

20

27

H

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM15

1-16

Note:

CDF LED = Cool/Dry/Fan LED, turns on in these modes.

The unit will not detect sensor missing when the compressor is ON.

LED INDICATOR LIGHTS: NORMAL OPERATION AND FAULT CONDITIONS FOR COOLING

Event PWR LED Timer LED Other LEDs Error Code

1. Room Sensor Open or Short Blink 1 time - Blink Fan Blink E1

2. Indoor Coil Sensor Open Blink 2 times - Blink Dry & Fan Blink E2

3. Outdoor Coil Sensor Open Blink 3 times - Blink Dry Blink E3

4. Compressor Overload / Blink 1 time Blink Cool Blink E4

Indoor Coil Sensor

Short / Outdoor Coil

Sensor Short

5. Gas Leak Blink 3 times Blink Cool & Dry Blink E5

6. Water Pump Fault Blink 2 times Blink Cool & Fan Blink E6

7. Outdoor Defrost - No indication in display -

panel (Blink HEAT in SLM3)

8. Outdoor Coil Sensor Blink 5 times

EC AP

Blink E7

Exist (MS model)

Blink COOL & Blink COOL &

SLEEP & HEAT &

HEAT/SLEEP HEAT/SLEEP

9. Hardware Error Blink 6 times Blink Heat, Cool, Blink E8

(tact switch pin short) follow by Fan, Dry

Causes / Action

- Protection against frequent starting. Wait for 3 to 4

minutes for the compressor to start operating.

- Power failure, or the fuse need to be replaced.

- The power plug is disconnected.

- It is possible that your delay timer has been set

incorrectly.

- If the fault persist after all these verifications, please

contact the air conditioner unit installer.

- The air filter is dirty.

- The doors or windows are open.

- The air suction and discharge are clogged.

- The regulated temperature is not high enough.

- Odors may be caused by cigarettes, smoke particles,

perfume etc. which might have adhered onto the coil.

- This is caused by air humidity after an extended long

period of operation.

- The set temperature is too low, increase the temperature

setting and operate the unit at high fan speed.

- Switch off unit and call dealer.

- Refrigerant fluid flowing into the evaporator coil.

Fault

1. The compressor does not operate

3 minutes after the air conditioner unit is started.

2. The air conditioner unit does not operate.

3. The air flow is too low.

4. Discharge air flow has bad odor.

5. Condensation on the front air grille of the indoor

unit.

6. Water flowing out from the air conditioner unit.

7. Hissing air flow sound from the air conditioner

unit during operation.

If any malfunction of the air conditioner unit is noted, immediately switch off the power supply to the unit. Check the

following fault conditions and causes for some simple troubleshooting tips.

TROUBLESHOOTING

If the fault persists, please call your local dealer / serviceman.

1 IM-CEE-1108(0)-EN AS 5/26/09, 3:14 PM16

2-1

Français

CONTOUR ET DIMENSIONS

Unité Intérieure

Toutes les dimensions sont données en mm/(pouces)

A

B

E

C

D

G

F

Unité Extérieure ((5)SL35/40C/CR)

Toutes les dimensions sont données en mm/(pouces)

Dimension A B C D E F G

(5)CE 35E/ER

1272 1088 74 1320 268 635 259

(50,1) (42,8) (2,9) (52,0) (10,6) (25,0) (10,2)

(5)CE 40E/ER

1490 1308 74 1538 268 635 259

(5,9) (51,5) (2,9) (60,6) (10,6) (25,0) (10,2)

1000,0 (39,4)

400,0 (15,7)

320,0 (12,6)

40,0

(1,6)

40,0

(1,6)

745,6 (29,4)

141,5 (5,6)

488,0 (19,2)

25,0 (1,0)

850,0 (33,5)

50,0

(2,0)

35,0

(1,4)

2 IM-CEE-1108(0)-FR AS 5/26/09, 3:15 PM1

2-2

! AVERTISSEMENT

Vérifier les points suivants au cours de l’installation.

• Ne pas installer l’appareil où il peut se produire des

fuites de gaz inflammable.

En cas de fuite et accumulation de gaz autour de

l’appareil, il y a risque d’incendie.

• S’assurer que le tuyau d’évacuation du condensat

est correctement branché.

Si le tuyau d’évacuation n’est pas correctement

branché, les éventuelles fuites d’eau risquent de

mouiller le mobilier.

• Ne pas surcharger l’unité (en fluide frigorigène).

Cet appareil est préchargé en usine. Une charge

trop importante risque de provoquer une surcharge

électrique ou d’endommager le compresseur.

• S’assurer que le panneau supérieur de l’appareil est

remis en place après l’installation ou l’entretien.

Avec un panneau mal fixé l’appareil va fonctionner

bruyamment.

• Les bords coupants et les surfaces du refroidisseur

tuulaire présentent un risque de blessure.

Mieux vaut éviter le contact avec ces endroits.

• Avant de couper l’alimentation électrique, veiller à

ce que l’interrupteur ON/OFF de la télécommande

soit en position “OFF” afin d’éviter une mise en

marche intempestive de l’appareil. Si l’interrupteur

de la télécommande n’est pas en position “OFF”, les

ventilateurs de l’appareil se mettront en marche dès que

l’alimentation électrique est rétablie. Il peut en résulter

un danger pour le personnel d’entretien ou l’utilisateur.

• Ne pas utiliser d’appareil de chauffage trop près du

climatiseur. Une chaleur excessive peut déformer ou

faire fondre le boîtier de plastic.

• S’assurer que la couleur des câbles de l’unité

extérieure et les marquages de bornes sont identiques

à ceux de l’unité intérieure.

• IMPORTANT : NE PAS INSTALLER OU

UTILISER LE CLIMATISEUR DANS UNE

BUANDERIE.

• N’utilisez pas de câbles joints et torsadés pour

l’alimentation électrique entrante.

! ATTENTION

• L’installation et la maintenance doivent être exécutées

par une personne qualifiée qui est familiarisée avec les

lois et réglementations en vigueur, et aussi

expérimentée dans ce type d’équipements.

• Tous les câblages doivent répondre aux réglementations

électriques nationales.

• Avant de commencer le raccordement suivant le schéma

électrique, s’assurer que la tension nominale de

l’appareil corresponde bien à celle indiquée sur la

plaque signalétique.

• L’ unité doit être raccordée à la TERRE pour prévenir

tous les risques possibles dûes à un défaut d’isolation.

• Les fils électriques ne doivent en aucun cas être en

contact avec les tuyaux de réfrigérant ou les parties

mobiles des moteurs du ventilateur.

• Avant l’installation ou l’entretien du climatiseur,

s’assurer que l’appareil est éteint (OFF).

• Débrancher l’appareil du circuit d’alimentation secteur

avant de procéder à l’entretien du climatiseur.

• NE PAS retirer le câble d’alimentation électrique de la

prise quand l’appareil est sous branché. Il peut en

résulter des décharges électriques importantes

susceptibles de provoquer un incendie.

• Les unités intérieures et extérieures, le cordon

d’alimentation et le câblage de transmission doivent

rester à une distance d’au moins 1 m des téléviseurs et

des radios, ce afin d’éviter les images déformées et les

parasites. {En fonction du type et de la source des ondes

électriques, des parasites peuvent être entendus même

avec une distance supérieure à 1 m}.

PRÉCAUTIONS DE SÉCURITÉ

Ce manuel fournit les procédures d’installation pour assurer le bon fonctionnement et la sécurité de cet appareil.

Des ajustements peuvent être nécéssaires pour suivre les réglementations locales.

Avant d’installer et de faire fonctionner le climatiseur, lisez attentivement ce manuel et conservez le.

MANUEL D’INSTALLATION

AVIS

Instructions d’élimination

Cet appareil de conditionnement d’air porte le symbole ci-joint. Ce symbole signifie que les appareils électriques

et électroniques doivent être éliminés séparément des ordures ménagères non triées.

N’essayez pas de démonter vous-même l’appareil : le démontage de l’appareil de conditionnement d’air ainsi

que le traitement du réfrigérant, de l’huile et d’autres composants doivent être effectués par un installateur

qualifié, en accord avec les réglementations locales et nationales en vigueur.

Les appareils de conditionnement d’air doivent être traités dans des installations spécialisées de dépannage,

réutilisation ou recyclage. En vous assurant que cet appareil est éliminé correctement, vous contribuez à

éviter les conséquences potentiellement néfastes sur l’environnement et la santé. Veuillez contacter votre

installateur ou les autorités locales pour plus d’information.

Les piles de la télécommande doivent être enlevées et éliminées séparément, conformément aux réglementations

locales et nationales en vigueur.

2 IM-CEE-1108(0)-FR AS 5/26/09, 3:15 PM2

Страница загружается...

Acson 5CE 40E Инструкция по установке

Похожие модели бренда

Модели других брендов