Sony CDP-XE530 Инструкция по применению

Бренд: Sony

Модель: CDP-XE530

Категория: Плееры CD

Тип: Инструкция по применению

Это руководство также подходит для

CDP-XE330

4-227-865-41 (1)

 1999 Sony Corporation

CDP-XE530

CDP-XE330

Compact Disc

Player

Operating Instructions

Instrukcja obslugi

ИнcтpyкЗио пo ТкcплyaтaЗии

WARNING

To prevent fire or shock

hazard, do not expose the unit

to rain or moisture.

To avoid electrical shock, do

not open the cabinet. Refer

servicing to qualified

personnel only.

The laser component in this product

is capable of emitting radiation

exceeding the limit for Class 1.

This appliance is classified as a CLASS 1

LASER product. The CLASS 1 LASER

PRODUCT MARKING is located on the

rear exterior.

Precautions

On safety

• Caution — The use of optical

instruments with this product will

increase eye hazard.

• Should any solid object or liquid fall

into the cabinet, unplug the player and

have it checked by qualified personnel

before operating it any further.

On power sources

• Before operating the player, check that

the operating voltage of the player is

identical with your local power

supply. The operating voltage is

indicated on the nameplate at the rear

of the player.

• The player is not disconnected from

the AC power source (mains) as long

as it is connected to the wall outlet,

even if the player itself has been

turned off.

• If you are not going to use the player

for a long time, be sure to disconnect

the player from the wall outlet. To

disconnect the AC power cord (mains

lead), grasp the plug itself; never pull

the cord.

• AC power cord must be changed only

at the qualified service shop.

On placement

• Place the player in a location with

adequate ventilation to prevent heat

build-up in the player.

• Do not place the player on a soft

surface such as a rug that might block

the ventilation holes on the bottom.

• Do not place the player in a location

near heat sources, or in a place subject

to direct sunlight, excessive dust or

mechanical shock.

On operation

• If the player is brought directly from a

cold to a warm location, or is placed in

a very damp room, moisture may

condense on the lenses inside the

player. Should this occur, the player

may not operate properly. In this case,

remove the disc and leave the player

turned on for about an hour until the

moisture evaporates.

On adjusting volume

• Do not turn up the volume while

listening to a portion with very low

level inputs or no audio signals. If you

do, the speakers may be damaged

when a peak level portion is played.

On cleaning

• Clean the cabinet, panel and controls

with a soft cloth slightly moistened

with a mild detergent solution. Do not

use any type of abrasive pad, scouring

powder, or solvent such as alcohol or

benzine.

If you have any questions or

problems concerning your player,

please consult your nearest Sony

dealer.

Getting Started

Welcome!

Thank you for purchasing the Sony

Compact Disc Player. Before operating

the unit, please read this manual

thoroughly and retain it for future

reference.

About This Manual

The instructions in this manual are for

models CDP-XE530 and CDP-XE330.

The CDP-XE530 is the model used for

illustration purposes. Any difference in

operation is clearly indicated in the text,

for example, “CDP-XE530 only.”

Conventions

• Instructions in this manual describe

the controls on the player.

You can also use the controls on the

remote if they have the same or

similar names as those on the player.

• The following icons are used in this

manual:

Indicates that you can do the

task using the remote.

Indicates hints and tips for

making the task easier.

TABLE OF CONTENTS

Getting Started

Unpacking........................................................................................................ 4

Hooking Up the System ................................................................................. 4

Playing a CD........................................................................................................ 6

Playing CDs

Using the Display ........................................................................................... 7

Locating a Specific Track or a Particular Point in a Track ........................ 9

Playing Tracks Repeatedly .......................................................................... 10

Playing in Random Order (Shuffle Play) .................................................. 11

Creating Your Own Programme (Programme Play) ............................... 12

Recording From CDs

Recording Your Own Programme ............................................................. 14

Recording a CD by Specifying Tape Length (Time Edit)

(CDP-XE530 only) ......................................................................................... 14

Fading In or Out............................................................................................ 15

Adjusting the Recording Level (Peak Search) .......................................... 17

Additional Information

Notes on CDs ................................................................................................. 17

Troubleshooting ............................................................................................ 18

Specifications ................................................................................................. 18

Index

Index ............................................................................................................... 19

Getting Started

Unpacking

Check that you received the following items:

• Audio connecting cord (1)

• Remote commander (remote) (1)

• R6 (size AA) batteries (2)

Inserting batteries into the remote

You can control the player using the supplied remote.

Insert two R6 (size AA) batteries by matching the + and

– on the batteries to the diagram inside the battery

compartment.

Insert the negative (–) end first, then push in and down

until the positive (+) end clicks into position.

When using the remote, point it at the remote sensor g

on the player.

Hooking Up the System

Overview

This section describes how to hook up the CD player to

an amplifier. Be sure to turn off the power of each

component before making the connections.

White

(L)

Red

(R)

White

(L)

Red

(R)

What cords will I need?

Audio cord (supplied) (1)

Hookups

When connecting an audio cord, be sure to match the

colour-coded cord to the appropriate jacks on the

components: Red (right) to Red and White (left) to

White. Be sure to make connections firmly to avoid

hum and noise.

AmplifierCD player

INPUT

LINE

OUT

When to replace batteries

With normal use, the batteries should last for about six

months. When the remote no longer operates the player,

replace all the batteries with new ones.

Notes

• Do not leave the remote near an extremely hot or humid

place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.

• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from battery

leakage and corrosion.

CD player

Audio input

(L)

: Signal flow

Amplifier

To mains

Audio input

(R)

LINE OUT

(R)

LINE OUT

(L)

Getting Started

You can adjust the output level to the amplifier

Press LINE OUT LEVEL +/– on the remote. You can

reduce the output level up to –20 dB.

When you reduce the output level, “FADE” (or for

the CDP-XE330) appears in the display.

When you turn off the player, the output level

automatically returns to the maximum level.

• If you have a digital component such as a digital

amplifier, D/A converter, DAT, or MD

Connect the component via the DIGITAL OUT (OPTICAL)

connector using the optical cable (not supplied). Take off

the cap and plug in the optical cable.

Note that you cannot use the following functions when

making this connection:

• Fading In or Out (see page 15)

• Time Fade (see page 16)

• Adjusting the output level using the LINE OUT

LEVEL +/– buttons on the remote (see above)

Connecting the mains lead

Connect the mains lead to a wall outlet.

Where do I go next?

Now you’re ready to use your player.

If you aren’t familiar with how to play CDs, go to the section

“Playing a CD” on page 6.

Then, go to the following sections for other operations.

POC-15

Optical cable (not supplied)

Digital component

CD player

Note

When you connect via the DIGITAL OUT (OPTICAL)

connector, noise may occur when you play CD software other

than music, such as a CD-ROM.

If you have a Sony component with the CONTROL A1

jack (CDP-XE530 only)

Connect the component via the CONTROL A1 jack. You

can simplify the operation of audio systems composed of

separate Sony components. For details, refer to the

supplementary “S-Link

/CONTROL-A1 Control

System” instructions.

OPTICAL

DIGITAL

OUT

OPTICAL

DIGITAL

INPUT

FADE

Basic Operations

Turn on the amplifier and select the CD player position so that

you can listen to the sound from this player.

Press U (Power) to turn on the player.

Press § OPEN/CLOSE,

and place a disc on the

disc tray.

Press ·.

The disc tray closes and the player plays all the tracks once

(Continuous Play).

Adjust the volume on the amplifier.

To stop playback

Press p.

Playing a CD

• See pages 4 – 5 for the hookup

information.

Pause

Resume play after pause

Go to the next track

Go back to the preceding track

Stop play and remove the CD

You need to

Press P

Press P or ·

Turn ≠ AMS ± clockwise

Turn ≠ AMS ±

counterclockwise

Press § OPEN/CLOSE

If you turn on the player with

a CD in the tray

You can start playing

automatically from the

beginning of the CD. If you

connect a commercially

available timer, you can start

playing the CD at any time

you want.

You can adjust the output

level with the LINE OUT

LEVEL +/– on the remote Z

You can adjust the

headphones volume on the

remote (CDP-XE530 only) Z

Connect the headphones to

the PHONES jack and adjust

the volume with the LINE

OUT LEVEL +/– on the

remote.

Connect the

headphones.*

With the label side up

*CDP-XE530 only

OPEN/CLOSE

TIME/TEXT

AMS

EDIT/TIME FADE

PHONES

REPEATPLAY MODE

LANGUAGE

MUSIC SCAN

PEAK SEARCH

CHECK CLEAR

Playing CDs

While in Shuffle Play mode (“SHUFFLE” appears in

the display; see page 11), a one-second access time

blank is added between each track. This increase is

automatically added to the total playing time in the

display.

The information also appears when you press

§ OPEN/CLOSE to close the disc tray.

Using the Display

You can check information about the disc using the

display.

• CDP-XE530

Playing CDs

Basic Operations

TIME/TEXT

• CDP-XE330

TIME

Checking the total number and playing

time of the tracks

Press TIME/TEXT (or TIME on the remote and for the

CDP-XE330) before you start playing.

The display shows the total number of tracks, total

playing time, and music calendar.

Music calendar

Total playing time

Total number of

tracks

Press

If the track number exceeds 24 (or 68 for the CDP-XE330),

“– – . ––” appears instead of the remaining time.

Press

Playing time of the

current track

Remaining time on

the current track

Remaining time on

the disc

Display information while playing a disc

While playing a disc, the display shows the current

track number, index number (CDP-XE530 only),

playing time, and the music calendar.

LANGUAGE

≠ AMS ±

1 2 345

678910

TRACK INDEX

MIN SEC

12345

678910

TRACK INDEX

MIN SEC

Music calendar

Playing time

Current track

number

Index number

Checking the remaining time

Each time you press TIME/TEXT (or TIME on the

remote and for the CDP-XE330) while playing a disc,

the display changes as shown in the chart below.

• CDP-XE530

• CDP-XE330

The track numbers in the music calendar disappear

after they are played.

12345

678910

MIN SEC

Music calendar

Playing time

Current track number

DISPLAY

ON/OFF

TIME

If the remaining time exceeds 100 minutes in Programme

Play mode or when the disc has more than 24 (or 68 for the

CDP-XE330) tracks, “– – . ––” appears instead of the

remaining time.

12345

678910

TRACK INDEX

MIN SEC

12345

678910

MIN SEC

12345

678910

TRACK INDEX

MIN SEC

• CDP-XE530 • CDP-XE330

TIME

Playing CDs

• While playing a disc

Press

12345

678910

TRACK

TEXTCD

12345

678910

TRACK INDEX

MIN SEC

TEXTCD

12345

678910

TRACK INDEX

MIN SEC

TEXTCD

12345

678910

MIN SEC

TEXTCD

Playing time of the

current disc

Track title

Remaining time on

the current track

Remaining time on

the disc

If the track number exceeds 24,

“– – . ––” appears instead of the

remaining time.

Press

If a title or name has more than 12 characters, the first

12 characters will light up after the title or name scrolls

by in the display.

This information also appears

when the player locates the track.

Notes

• The display may not show all the characters depending on

the disc.

• This player can only display the disc titles, track titles, and

artist names from CD TEXT discs. Other information cannot

be displayed.

Checking the information of CD TEXT discs

in other languages (CDP-XE530 only)

You can change the displayed language if your CD

TEXT disc has multi language capacity. When the

player detects such a CD TEXT disc, the display shows

the current operating language after “CD TEXT” and

“MULTI” appear in the display.

If the player cannot read the language memorised in a

CD TEXT disc, the display shows “<OTHER LANG>”

after the player detects the disc.

• Before you start playing

12345

678910

DISC

TEXTCD

12345

678910

ART.

TEXTCD

12345

678910

TRACK INDEX

MIN SEC

TEXTCD

Press

Total number of

tracks and total

playing time

Press

Artist name

Disc title

Checking the information of CD TEXT discs

(CDP-XE530 only)

CD TEXT discs have information, such as the disc titles

or artist names, memorised in a blank space on the

discs where, on normal discs, there is no information.

The display shows the CD TEXT information of the

disc so that you can check the current disc title, artist

name, and track title. When the player detects CD

TEXT discs, the “CD TEXT” indication appears in the

display. If your CD TEXT disc has multi language

capacity, “CD TEXT” and “MULTI” indications appear

in the display. If you want to check the information in

another language, refer to “Checking the information

of CD TEXT discs in other languages” on page 8.

Each time you press TIME/TEXT (or TIME on the

remote), the display changes as shown in the chart

below.

If the remaining time exceeds 100 minutes in

Programme Play mode or when the disc has more

than 24 tracks, “– – . ––” appears instead of the

remaining time.

Playing CDs

Locating a Specific Track or a

Particular Point in a Track

You can quickly locate any track while playing a disc

using the AMS (Automatic Music Sensor) on the player

or number buttons on the remote.

You can also locate a particular point in a track while

playing a disc.

0/)

≠ AMS ±

Number

buttons

>10

=/+

0/)

MUSIC SCAN

(CDP-XE530 only)

Turning off indications in the display

(CDP-XE530 only)

Each time you press DISPLAY ON/OFF on the remote

while playing a disc, the display turns off and on

alternately.

Even when the display is turned off, the display turns

on if you pause or stop play. When you resume play,

the display turns off again.

Before you start playing, when you press DISPLAY

ON/OFF to turn off the display, “DISPLAY OFF”

appears, and when you press the button to turn on the

display, “DISPLAY ON” appears.

1 Before playing a CD TEXT disc, press

LANGUAGE.

“SELECT LANG” and the current operating

language appear in the display.

2 Turn ≠ AMS ± until the language you want

to select appears in the display.

3 Push ≠ AMS ± to select the language.

“READING TEXT” appears momentarily, then the

display shows the new selected language.

4 Press TIME/TEXT (or TIME on the remote)

repeatedly until the information you want to check

appears (see page 8).

Notes

• If your CD TEXT disc is not equipped with other languages,

“CAN’T SELECT” appears in the display when you press

the LANGUAGE button.

• If you press LANGUAGE while playing a CD TEXT disc,

the current operating language appears momentarily.

• The operating language you have selected remains until

you turn off the power.

Number

buttons

>10

=/+

0/)

• CDP-XE530

• CDP-XE330

(Continued)

Playing CDs

• CDP-XE530

REPEAT

• CDP-XE330

REPEAT

Playing Tracks Repeatedly

You can play tracks repeatedly in any play mode.

When you directly locate a track numbered over 10

Press >10 first, then the corresponding number buttons.

To enter “0,” use button 10.

Example: To play track number 30

Press >10 first, then 3 and 10.

You can extend the playing time during Music Scan

(CDP-XE530 only)

Press MUSIC SCAN repeatedly until the playing time

you want (10, 20 or 30) appears in the display. Each time

you press the button, the playing time changes cyclically.

Note

If “- OVER -” (or “ ” for the CDP-XE330) appears in the

display, the disc has reached the end while you were pressing

). Press 0 or turn ≠ AMS ± counterclockwise to go

back.

To locate

The next or

succeeding tracks

The current or

preceding tracks

A specific track

directly

By scanning each

track for 10 seconds

(Music Scan)

(CDP-XE530 only)

A point while

monitoring the sound

A point quickly by

observing the display

during pause

You need to

Turn ≠ AMS ± clockwise until

you find the track. When using the

remote, press + repeatedly until you

find the track.

Turn ≠ AMS ± counterclockwise

until you find the track. When using

the remote, press = repeatedly until

you find the track.

Turn ≠ AMS ± until you find the

track number you want. When using

the remote, press the number button of

the track.

Press MUSIC SCAN. When you find

the track you want, press · to start

playing the track.

Press ) (forward) or 0 (backward)

and hold down until you find the

point.

Press ) (forward) or 0 (backward)

and hold down until you find the

point. You will not hear the sound

during the operation.

Press REPEAT while playing a disc.

“REPEAT” appears in the display. The player repeats

the tracks as follows:

When the disc is played in

Continuous Play (page 6)

Shuffle Play (page 11)

Programme Play (page 12)

To cancel Repeat Play

Press REPEAT twice.

The player repeats

All the tracks

All the tracks in random order

The same programme

Repeating the current track (Repeat 1)

You can repeat only the current track in any play

mode.

While the track you want is being played, press

REPEAT repeatedly until “REPEAT 1” appears in the

display.

To cancel Repeat 1

Press REPEAT.

Playing CDs

Playing in Random Order

(Shuffle Play)

You can have the player “shuffle” tracks and play in a

random order.

PLAY MODE

1 Press PLAY MODE repeatedly until “SHUFFLE”

appears in the display.

When using the remote, press SHUFFLE.

2 Press · to start Shuffle Play.

The indication appears while the player is

“shuffling” the tracks.

To cancel Shuffle Play

Press PLAY MODE twice.

When using the remote, press CONTINUE.

You can start Shuffle Play while playing

Press PLAY MODE repeatedly until “SHUFFLE” appears

in the display. When using the remote, press SHUFFLE.

Shuffle Play starts from the current track.

Repeating a Specific Portion (A˜B Repeat)

(CDP-XE530 only)

You can play a specific portion in a track repeatedly.

This might be useful when you want to memorise

lyrics.

Note that you cannot repeat a portion extending to two

tracks.

A – B

1 While playing a disc, press A – B on the remote

when you find the starting point (point A) to be

played repeatedly.

“A-” of “REPEAT A-” flashes in the display.

2 When you reach the ending point (point B), press

A – B again.

“REPEAT A-B” appears. The player plays this

specific portion repeatedly.

To cancel A˜B Repeat

Press REPEAT.

Setting a new starting point

You can move the repeating portion ahead by

changing the starting point.

1 Press A – B while the player is repeating the

specific portion.

The ending point B becomes the new starting point

A. “A-” of “REPEAT A-” flashes in the display.

2 When you reach the ending point (point B), press

A – B again.

“REPEAT A-B” appears. The player repeats

between the new starting and ending points.

When you want to restart from the starting point A

Press · during A˜B Repeat.

SHUFFLE

Playing CDs

Creating Your Own Programme

(Programme Play)

You can arrange the order of the tracks on a disc and

create your own programme. The programme can

contain up to 24 tracks.

• CDP-XE530

CHECK

CLEAR ≠ AMS ±

PLAY MODE

• CDP-XE330

CHECK CLEAR ≠ AMS ±

PLAY MODE ·

• CDP-XE530

TRACK STEP

MIN SEC

PROGRAM

Playing order

Total playing time

Track number being

programmed

• CDP-XE330

MIN SEC

PROGRAM

Total playing time

Track number being

programmed

If you’ve made a mistake

Press CLEAR, then repeat Steps 2 and 3.

4 Repeat Steps 2 and 3 to programme the tracks in

the order you want.

5 Press · to start Programme Play.

To cancel Programme Play

Press PLAY MODE.

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

The programme remains until erased (see page 13) or

until you press §OPEN/CLOSE

The programme you have created remains even after the

Programme Play mode ends or you select another play

mode.

Notes

• The total playing time doesn’t appear in the display when it

exceeds 100 minutes.

• If you programme a track numbered over 24 (or 68 for the

CDP-XE330), “– – . ––” appears instead of the total playing

time.

•“PROGRAM FULL” (or “FULL” for the CDP-XE330)

appears in the display when you try to add a track to a

programme which already contains 24 tracks.

3 Push ≠ AMS ± to select the track.

• CDP-XE530

Playing order

Total playing time

• CDP-XE330

TRACK STEP

MIN SEC

PROGRAM

TAPE A

Last programmed track

Programmed tracks

STEP

PROGRAM

MIN SEC

PROGRAM

Last programmed track

Playing order

Programmed tracks

Total playing time

After one second

Creating a programme on the player

1 Press PLAY MODE repeatedly until “PROGRAM”

appers in the display before you start playing.

2 Turn ≠ AMS ± until the track number you

want appears in the display.

Playing CDs

Creating a programme using the remote

1 Press PROGRAM before you start playing.

“PROGRAM” appears in the display.

2 Press the number buttons of the tracks you want to

programme in the order you want.

Example: To programme the tracks 2, 8 and 5.

Press the number buttons in the order

2, 8 and 5.

To select a track with a number over 10

Use >10 button (see page 10).

If you’ve made a mistake

Press CLEAR, then press the correct track number.

3 Press · ( or ( for the CDP-XE330) to start

Programme Play.

To cancel Programme Play

Press CONTINUE.

You can check the total playing time while

programming using the remote (Programme Edit)

To select a track, press = or + and check the total

playing time. Then press PROGRAM to confirm your

selection.

Notes

• The total playing time doesn’t appear in the display when it

exceeds 100 minutes.

• If you programme a track numbered over 24 (or 68 for the

CDP-XE330), “– – . ––” appears instead of the total playing

time.

•“PROGRAM FULL” (or “FULL” for the CDP-XE330)

appears in the display when you try to add a track to a

programme which already contains 24 tracks.

Checking the track order

You can check your programme before or after you

start playing.

Press CHECK.

Each time you press this button, the display shows the

track number in the programmed order. After the last

track in the programme, the display shows “- END -”

(or “End” for the CDP-XE330) and returns to the

original display. If you check the order after you start

playing, the display shows only the remaining track

numbers.

Changing the track order

You can change your programme before you start

playing.

Erase a track

Erase the last track in the

programme

Add tracks to the end of

the programme

Change the whole

programme completely

You need to

Press CHECK until the track

you don’t want appears in

the display, then press

CLEAR.

Press CLEAR. Each time you

press the button, the last

track will be cleared.

Turn ≠ AMS ± until

the track number you want

to add appears, then push

≠ AMS ±.

When using the remote,

press the number buttons of

the tracks to be added.

Hold down CLEAR until

“CLEAR” (for the CDP-

XE530) or “CLEAr” (for the

CDP-XE330) appears in the

display. Create a new

programme following the

programming procedure.

• CDP-XE530

• CDP-XE330

Number buttons

PROGRAM

CLEAR

CHECK

>10

Number buttons

>10

(

PROGRAM

CLEAR

CHECK

Recording From CDs

Recording a CD by Specifying

Tape Length (Time Edit)

(CDP-XE530 only)

You can have the player create a programme that will

match the length of the tape. In this feature, the player

creates a programme basically keeping the original

order of the disc. However, the player may change the

last track of each side to match the recording time to

the tape length.

i.e. Side A: track number 1n2n3n4n8

Side B: track number 5n6n7n9n10

The programme may contain up to 24 tracks (a pause

inserted between tracks is counted as one track).

Note that tracks numbered over 24 cannot be

programmed in this feature.

EDIT/TIME FADE

0/)

Recording Your Own

Programme

You can record the programme you’ve created on a

tape, DAT, or MD. The programme can contain up to

24 tracks.

By inserting a pause during programming, you can

divide the programme into two for recording on both

sides of a tape.

• CDP-XE530

• CDP-XE330

≠ AMS ±

PLAY MODE

1 Create your programme (for side A when

recording on a tape) while checking the total

playing time indicated in the display.

Follow Steps 1 to 4 in “Creating a programme on

the player” on page 12 or Steps 1 and 2 in

“Creating a programme using the remote” on page

13.

The “TAPE A” (or indication for the

CDP-XE330) appears in the display.

2 When you record on both sides of the tape, press

P to insert a pause.

The “P” and “TAPE B” (or indication for the

CDP-XE330) appear in the display and the playing

time is reset to “0.00.”

When you record on one side of the tape or on a

DAT or MD, skip this step and go to Step 4.

A pause is counted as one track

You can programme up to 23 tracks when you insert a

pause.

3 Repeat Step 1 to create the programme for side B.

≠ AMS ±

4 Start recording on the deck and then press · on

the player.

When you record on both sides of the tape, the player

pauses at the end of the programme for side A.

5 When you record on side B, reverse the tape and

press · or P on the player to resume playing.

To check and change your programme

See page 13.

The “TAPE A” (or indication for the CDP-XE330)

appears while checking the programme for side A and

“TAPE B” (or indication for the CDP-XE330)

appears while checking the programme for side B.

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

A B

Recording From CDs

Press EDIT/TIME FADE before you start playing

until “EDIT” appears and “TAPE A” flashes in the

display.

2 Press 0 or ) to specify the tape length.

Each time you press these buttons, the display

changes as shown below with the tape length of

one side .

When you select “HALF”

The player divides the total playing time of the disc in

half, keeping the original order.

Note that you cannot select “HALF” when the disc has

more than 24 tracks.

3 Press EDIT/TIME FADE to have the player create

the programme.

The display shows the tracks to be recorded.

“TAPE B” flashes in the display.

4 When you record on both sides of the tape, press

EDIT/TIME FADE again.

The player inserts a pause, then creates the

programme for side B. The display shows the

programmed tracks.

When you record on one side of the tape or on a

DAT or MD, skip this step.

5 Start recording on the deck and then press · on

the player.

When you record on both sides of the tape, the

player pauses at the end of the programme for side

6 Reverse the tape to side B and press · or P on

the player to resume playing the remaining tracks.

To cancel Time Edit

Press PLAY MODE.

When using the remote, press CONTINUE.

You can specify the tape length freely

You can set the tape length using ≠ AMS ±.

Example: When the tape length of one side is 30 minutes

and 15 seconds

1 To set the minutes, turn ≠ AMS ± until

“30” appears in the display, then push

≠ AMS ±.

2 To set the seconds, turn ≠ AMS ± until

“15” appears in the display, then push

≠ AMS ±.

n HALF ˜ C-46 23.00 ˜ C-54 27.00 ˜ C-60 30.00 N

n - -. - - ˜ C-90 45.00 ˜ C-74 37.00 N

Fading In or Out

You can manually fade in or out to prevent tracks from

starting or ending abruptly.

Note that you cannot use this effect when you use the

DIGITAL OUT (OPTICAL) connector.

Fading in or out at the point you want

FADER

• CDP-XE530

Number buttons

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

To check and change your programme

See page 13.

(Continued)

FADER

• CDP-XE330

Recording From CDs

n HALF ˜ C-46 23.00 ˜ C-54 27.00 ˜ C-60 30.00 N

n - -. - - ˜ C-90 45.00 ˜ C-74 37.00 N

Fading out at the specified time

(Time Fade) (CDP-XE530 only)

You can have the player fade out automatically by

specifying the playing time. Once you set the time fade,

it works twice, that is, the play fades out at the end of

both sides of a tape.

Changing the fading time (CDP-XE530 only)

You can change the fading time from 2 to 10 seconds

before fading in or out. If you don’t change it, fading

lasts for 5 seconds.

1 Before you start playing, press FADER.

2 Press the number buttons to specify the fading

time.

Notes

• The fading time is reset to 5 seconds when you turn off the

player.

• If you press FADER during Music Scan (page 10), fading

time changes to 2 seconds.

EDIT/TIME FADE0/)

1 Press EDIT/TIME FADE repeatedly before you

start playing until “T.FADE” and “TAPE A”

appear in the display.

2 Press 0 or ) to specify the playing time. Each

time you press these buttons, the display changes

as shown below with the tape length of one side.

When you select “HALF”

The player sets the playing time to a half of the total

playing time.

3 Press · to start playing.

At the specified time the play fades out and the

player pauses. “TAPE B” appears in the display.

4 Reverse the tape to side B and press · or P on

the player to resume playing the remaining tracks.

Again, the play fades out at the specified time.

To cancel Time Fade

Press EDIT/TIME FADE.

You can freely specify the playing time

See “You can specify the tape length freely” on page 15.

You can change discs during Time Fade

If the play ends before the specified fade-out time, (for

example, when you record CD-singles on a tape) you can

change the disc. The specified fade-out time is counted

only during playing.

You can fade in to resume playing in Step 4

After you reverse the tape, press FADER on the remote.

Notes

• Time Fade will be cancelled if you press 0 or ) during

the operation.

•“HALF” does not appear when the disc has more than 24

tracks.

Start play fading in

End play fading out

Press FADER

During pause. For the CDP-XE530,

“FADE” flashes. For the CDP-

XE330, lights up and the Q

indication flashes. Then play fades

in.

When you want to start fading out.

For the CDP-XE530, “FADE”

flashes. For the CDP-XE330 ,

lights up and the q indication

flashes. Then play fades out and the

player pauses.

Fading time lasts for 5 seconds. If you press FADER

during Music Scan (page 10), fading time changes to 2

seconds (CDP-XE530 only).

FADE

Recording From CDs

Adjusting the Recording Level

(Peak Search)

The player locates the highest level among the tracks to

be recorded to let you adjust the recording level before

you start recording.

1 Before you start playing, press PEAK SEARCH.

“PEAK” flashes in the display and the player starts

scanning the disc searching for the highest peak

level.

After scanning all the tracks, the player repeats the

portion with the highest peak level.

2 Adjust the recording level on the deck.

3 Press p on the player to stop Peak Search.

“PEAK” disappears from the display.

Note

The portion with the highest level may differ every time you

try the adjustment on the same disc. The difference is,

however, so slight that you won’t find any problem in

adjusting the recording level precisely.

PEAK SEARCH

PEAK SEARCH p

• CDP-XE530

• CDP-XE330

Notes on CDs

On handling CDs

• To keep the disc clean, handle the disc by its edge. Do not

touch the surface.

• Do not stick paper or tape on the disc.

• Do not expose the disc to direct sunlight or heat sources

such as hot air ducts, nor leave it in a car parked in direct

sunlight as there can be considerable rise in temperature

inside the car.

• Do not use any commercially available stabilizer. If you do,

the disc and the player may be damaged.

• After playing, store the disc in its case.

On cleaning

• Before playing, clean the disc with a cleaning cloth. Wipe

the disc from the centre out.

• Do not use solvents such as benzine, thinner,

commercially available cleaners or anti-static spray

intended for vinyl LPs.

Additional Information

Recording From CDs

Additional Information

Specifications

Compact disc player

Laser Semiconductor laser (λ = 780 nm)

Emission duration: continuous

Laser output Max 44.6 µW*

* This output is the value measured at

a distance of 200 mm from the

objective lens surface on the Optical

Pick-up block with 7 mm aperture.

Frequency response 2 Hz to 20 kHz ± 0.5 dB

Signal-to-noise ratio More than 100 dB

Dynamic range CDP-XE530: More than 98 dB

CDP-XE330: More than 92 dB

Harmonic distortion CDP-XE530: Less than 0.0045%

CDP-XE330: Less than 0.005%

Channel separation More than 95 dB

Outputs

LINE OUT

DIGITAL

OUT

(OPTICAL)

PHONES

(CDP-XE530

only)

General

Power requirements 220 V – 230 V AC, 50/60 Hz

Power consumption CDP-XE530: 11 W

CDP-XE330: 10 W

Dimensions (approx.) 430 × 110 × 290 mm

(w/h/d) (17 × 4 3/8 × 11 1/2 in.) incl. projecting

parts

Mass (approx.) CDP-XE530: 3.4 kg (7 lbs 8 oz)

CDP-XE330: 3.1 kg (6 lbs 14 oz)

Supplied accessories

Audio cord (2 phono plugs – 2 phono plugs) (1)

Remote commander (remote) (1)

R6 (size AA) batteries (2)

Design and specifications are subject to change without notice.

Troubleshooting

If you experience any of the following difficulties while

using the player, use this troubleshooting guide to help

you remedy the problem. Should any problem persist,

consult your nearest Sony dealer.

There’s no sound.

/ Check that the player is connected securely.

/ Make sure you operate the amplifier correctly.

/ Adjust the output level with LINE OUT LEVEL +/–

on the remote.

The CD does not play.

/ There’s no CD inside the player. “- NO DISC -” (or

“no dISC” for the CDP-XE330) appears. Insert a CD.

/ Place the CD with the label side up on the disc tray

correctly.

/ Clean the CD (see page 17).

/ Moisture has condensed inside the player. Remove

the disc and leave the player turned on for about an

hour (see page 2).

The recording level has changed.

/ The recording level changes if you adjust the output

level with LINE OUT LEVEL +/– on the remote

during recording.

The remote does not function.

/ Remove the obstacles in the path of the remote and

the player.

/ Point the remote at the remote sensor g on the player.

/ Replace all the batteries in the remote with new ones

if they are weak.

Load

impedance

Over 10 kilohms

Wave length:

660 nm

32 ohms

Jack

type

Phono

jacks

Optical

output

connector

Stereo

phone

jack

Maximum

output level

2 V

(at 50 kilohms)

–18 dBm

10 mW

Additional Information

Index

Names of controls

Buttons

A – B11

CHECK 13

CLEAR 13

CONTINUE 11

EDIT/TIME FADE 15, 16

FADER 16

LANGUAGE 9

LINE OUT LEVEL +/– 5

MUSIC SCAN 10

Number 10

§ OPEN/CLOSE 6

PEAK SEARCH 17

PLAY MODE 11, 12

PROGRAM 13

REPEAT 10

SHUFFLE 11

TIME 7

TIME/TEXT 7

· 6

P 6

p 6

0/) 10

=/+ 10

>10 10

Switch

U (Power) 6

Connector

DIGITAL OUT (OPTICAL) 5

Jacks

LINE OUT 4

PHONES 6

Others

Disc tray 6

Display 7

≠ AMS ± 6

g 4

Index

A, B

A˜B Repeat 11

AMS 9

Automatic Music Sensor. See

AMS

C, D

CD TEXT 8

Connecting 4

Continuous Play 6

CONTROL A1 5

Editing. See Recording

F, G

Fading 15

Time Fade 16

H, I, J, K

Half disc (HALF) 15

Handling CDs 17

Hookups 4

overview 4

Locating

by monitoring 10

by observing the display 10

by scanning 10

directly 10

using AMS 10

M, N, O

Music Scan 10

P, Q

Peak Search 17

Playback

Continuous Play 6

Programme Play 12

Repeat Play 10

Shuffle Play 11

Programme 12

changing 13

checking 13

for recording 14

Programme Edit 13

Recording 14

a programme 14

using Time Edit 14

Remaining time 7

Remote control 4

Repeating

all 10

a specific portion 11

the current track 10

Scanning. See Music Scan

Searching. See Locating

Selecting the language 8

Shuffle Play 11

Time Edit 14

Time Fade 16

Total playing time 7

Troubleshooting 18

U, V, W, X, Y, Z

Unpacking 4

Środki ostrożności

Dotyczące bezpieczeństwa

• Ostrzeżenie — Manipulowanie przy

sprzęcie instrumentami optycznymi,

może być niebezpieczne dla wzroku.

• Jeżeli do wnętrza obudowy dostanie się

stałe lub płynne ciało obce, należy sprzęt

odłączyć od źródła zasilania i przed

podjęciem dalszej eksploatacji, oddać

do przeglądu przez odpowiednio

wykwalifikowany personel.

Dotyczące źródeł zasilania

• Przed rozpoczęciem eksploatacji, należy

upewnić się, że potrzebne napięcie

robocze sprzętu jest identyczne z

miejscowym napięciem sieci

elektrycznej. Niezbędne napięcie

robocze podano na tabliczce

znamiennej, umieszczonej na tylnej

ściance odtwarzacza.

• Wyłączony sprzęt, nie jest odłączony od

źródła zasilania (sieć elektryczna) dopóki

przewód zasilania jest podłączony do

gniazdka ściennego prądu AC.

• Przed dłuższą przerwą w eksplotacji

sprzętu, należy pamiętać o odłączeniu

odtwarzacza od sieci elektrycznej.

Przewód zasilania prądem AC (sieć

elektryczna) odłącza się przez

wyciągnięcie wtyczki; nigdy nie ciągnąć

za sam kabel.

• Wymianę przewodu zasilania prądem AC

zlecać wyłącznie fachowcom punktów

serwisowych.

Dotyczące umiejscowienia sprzętu

• Sprzęt należy ustawić w miejscu

zapewniającym odpowiednią wentylację,

zapobiegającą narastaniu ciepła

wewnątrz urządzenia.

• Nie ustawiać sprzętu na miękkich

powierzchniach, takich jak np. dywan,

powodujących zablokowanie otworów

wentylacyjnych dolnej powierzchni

sprzętu.

• Nie ustawiać sprzętu w pobliżu źródeł

ciepła, lub w miejscach narażonych na

bezpośrednie działanie promieni

słonecznych, nadmiernych ilości kurzu

lub wstrząsy mechaniczne.

Dotyczące działania sprzętu

• Przeniesienie sprzętu bezpośrednio z

zimnego do ciepłego pomieszczenia, lub

ustawienie go w wilgotnym

pomieszczeniu, może spowodować

kondensację wilgoci na powierzchni

soczewki, umieszczonej wewnątrz

odtwarzacza. W takim wypadku,

funkcjonowanie sprzętu może być

nieprawidłowe. Należy wówczas usunąć

dysk CD z odtwarzacza i włączony

sprzęt pozostawić na około godzinę, aby

wilgoć mogła wyparować.

Dotyczące regulacji poziomu głośności

• Słuchając odcinka o niskim poziomie

dźwiękowych sygnałów wejściowych lub

odcinka bez zapisu sygnałów

wejściowych, nie należy zwiększać

poziomu głośności. W przeciwnym

wypadku można spowodować

uszkodzenie głośników w momencie

odtworzenia odcinka o szczytowym

poziomie dźwięku.

Dotyczące czyszczenia

• Obudowę, panel oraz kontrolki proszę

czyścić przy pomocy miękkiej ściereczki,

lekko zwilżonej w rozczynie łagodnego

detergentu. Nie należy używać gąbek

szorujących, proszków do czyszczenia,

lub rozpuszczalników zawierających

alkohol lub benzynę.

W przypadku ewentualnych pytań lub

niejasności dotyczących nabytego

odtwarzacza, prosimy o

skontaktowanie się z najbliższym

punktem obsługi lub sprzedaży

sprzętu Sony.

OSTRZEŻENIE

W celu uniknięcia

niebezpieczeństwa pożaru lub

porażenia prądem, nie należy

poddawać urządzenia

działaniu wilgoci lub deszczu.

W celu uniknięcia

niebezpieczeństwa porażenia

prądem nie należy otwierać

obudowy. Jedynie

wykwalifikowany personel jest

uprawniony do naprawy i

serwisu.

Laser będący komponentem tego

urządzenia jest w stanie emitować

promienie przekraczające normy

Klasy 1.

Niniejsze urządzenie jest

zaklasyfikowane jako produkt z CLASS 1

LASER (z laserem klasy 1). Oznakowanie

CLASS 1 LASER PRODUCT znajduje się

na zewnętrznej, tylnej stronie obudowy.

Страница загружается ...

Sony CDP-XE530 Инструкция по применению

Бренд: Sony

Модель: CDP-XE530

Категория: Плееры CD

Тип: Инструкция по применению

Это руководство также подходит для

CDP-XE330

Скачать PDF

сообщить о нарушении

на других языках

polski: Sony CDP-XE530 Instrukcja obsługi

Модели других брендов

Hyundai H-CDM8056 Руководство пользователя

Sony CDP-XE530 Инструкция по применению

Это руководство также подходит для

Sony CDP-XE530 Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов