Yamaha YSP-3000 Инструкция по применению

YSP-3000

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

Printed in Malaysia WK75380

YSP-3000

Digital Sound Projector

TM

OWNER’S MANUAL

UA

00cv_YSP-3000_UA.fm Page 1 Thursday, August 2, 2007 11:19 AM

IMPORTANT SAFETY INSTRUCTIONS

i En

■ Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert you to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert you to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

1

Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide

blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician

for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning

storms or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power supply cable or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT SAFETY INSTRUCTIONS

ii En

FCC INFORMATION (for US customers)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void

your authority, granted by the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories and/or another

product use only high quality shielded cables. Cable/s supplied

with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference

with other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the operation

of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is

found to be the source of interference, which can be determined

by turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures:

Relocate either this product or the device that is being affected

by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe

Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

We Want You Listening For A Lifetime

Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying

blaring or distortion – and, most importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries

Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

iii En

1

To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place with at least 5 cm (2 in) of space above (or below) this unit

– away from direct sunlight, heat sources, vibration, dust,

moisture, and/or cold.

3 Locate this unit away from other electrical appliances, motors, or

transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from cold

to hot, and do not locate this unit in an environment with high

humidity (i.e. a room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this

unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire, damage

to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this

unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to obstruct heat radiation. If the temperature inside

this unit rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all connections are

complete.

8 Do not operate this unit upside-down. It may overheat, possibly

causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power supply cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might damage

the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this unit

with a higher voltage than specified is dangerous and may cause

fire, damage to this unit, and/or personal injury. Yamaha will not

be held responsible for any damage resulting from use of this unit

with a voltage other than specified.

13 To prevent damage by lightning, keep the power supply cable

disconnected from a wall outlet or this unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the power supply cable from the wall

outlet.

16 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

17 Before moving this unit, press STANDBY/ON to set this unit in

standby mode, and disconnect the power supply cable from the

wall outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power supply cable from the

outlet, then leave the unit alone.

19 When using the unit for a long time, the unit may become warm.

Turn the power off, then leave the unit alone for cooling.

20 Install this unit near the AC outlet and where the AC power plug

can be reached easily.

21 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like.

Caution: Read this before operating this unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

WARNING

THE POWER SUPPLY CABLE OF THIS UNIT MUST BE

CONNECTED TO THE MAIN SOCKET OUTLET VIA A

PROTECTIVE EARTHING CONNECTION.

2

This unit is not disconnected from the AC power source as long as

it is connected to the AC wall outlet, even if this unit itself is

turned off by STANDBY/ON. This state is called the standby

mode. In this state, this unit is designed to consume a very small

quantity of power.

IMPORTANT

Please record the serial number of this unit in the space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit. Retain this

Owner’s Manual in a safe place for future reference.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide slot

and fully insert.

This Class B digital apparatus complies with Canadian ICES-003.

FOR U.K. CUSTOMERS

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the instructions

described below. Note that the plug severed from the mains lead

must be destroyed, as a plug with bared flexible cord is hazardous

if engaged in a live socket outlet.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED. Make

sure that neither core is connected to the earth terminal of the three

pin plug.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type.

CAUTION

Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation

exposure.

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

SETUP

English

1 En

Overview ................................................................. 2

Features .................................................................. 3

Using this manual .................................................. 5

Supplied accessories .............................................. 6

Controls and functions .......................................... 7

Front panel ................................................................ 7

Front panel display ................................................... 8

Rear panel ................................................................. 9

Remote control

(Europe, Australia, Asia, and Korea models) ..... 10

Remote control (U.S.A. and Canada models) ......... 13

Installation ............................................................ 16

Before installing this unit ........................................ 16

Installing this unit ................................................... 16

Connections .......................................................... 19

Before connecting components ............................... 20

Connections using HDMI cables ............................ 21

Connecting a TV ..................................................... 22

Connecting a DVD player/recorder ........................ 23

Connecting a digital satellite tuner or a cable TV tuner

............................................................................. 24

Connecting a digital airwave tuner ......................... 25

Connecting a portable audio player ........................ 26

Connecting other external components .................. 27

Connecting a subwoofer ......................................... 28

Connecting the FM antenna .................................... 29

About the IR IN terminal

(U.S.A. and Canada models only) ...................... 29

Connecting the AC power supply cable ................. 29

Getting started ..................................................... 30

Installing batteries in the remote control ................ 30

Operation range of the remote control .................... 30

Turning on this unit or setting it to

the standby mode ................................................ 31

Using SET MENU ................................................ 32

Displaying the OSD (on-screen display) ................ 32

The flow chart of SET MENU ................................ 33

Changing OSD language ..................................... 34

AUTO SETUP (IntelliBeam) .............................. 35

The flow chart of AUTO SETUP ........................... 35

Installing the IntelliBeam microphone ................... 36

Using AUTO SETUP (IntelliBeam) ....................... 37

Using the system memory ................................... 42

Convenient usage of the system memory ............... 42

Saving settings ........................................................ 42

Loading settings ...................................................... 43

Playback ............................................................... 45

Selecting the input source ....................................... 45

Playing back sources ............................................... 46

Adjusting the volume .............................................. 47

FM tuning ............................................................. 48

FM controls and functions ...................................... 48

Automatic tuning .................................................... 49

Manual tuning ......................................................... 49

Automatic preset tuning .......................................... 50

Manual preset tuning .............................................. 51

Selecting a preset station ........................................ 52

Displaying the Radio Data System information

(Europe model only) ........................................... 52

Enjoying surround sound ....................................54

5 Beam .................................................................... 54

Stereo plus 3 Beam ................................................. 55

3 Beam .................................................................... 55

My Surround ........................................................... 55

Enjoying 2-channel sources in surround sound ...... 57

Enjoying TV in surround sound ............................. 58

Adjusting surround mode parameters ..................... 59

Enjoying stereo sound ..........................................60

2-channel stereo playback ....................................... 60

5-channel stereo playback ....................................... 60

Playing back sound clearly (My Beam) ..............61

Using auto-adjust function ...................................... 61

Using manual-adjust function ................................. 62

Using sound field programs .................................63

CINEMA DSP programs ........................................ 64

Using the music enhancer ....................................66

Using the volume mode

(Night listening enhancer/TV volume equal mode)

67

Using the sleep timer ............................................68

Displaying the input source information ............70

Using the HDMI control feature .........................71

MANUAL SETUP ................................................72

Using MANUAL SETUP ....................................... 73

BEAM MENU ........................................................ 74

SOUND MENU ...................................................... 78

INPUT MENU ........................................................ 80

DISPLAY MENU ................................................... 83

Adjusting the audio balance ................................84

Using the test tone .................................................. 84

Using the audio output being played back .............. 85

Selecting the input mode ......................................87

Adjusting the system parameters .......................88

Using the system parameters .................................. 88

Setting the MEMORY PROTECT ......................... 89

Setting the MAX VOLUME ................................... 90

Setting the TURN ON VOLUME .......................... 90

Setting the DEMO MODE ..................................... 91

Setting the PANEL INPUT KEY ........................... 92

Disabling the front panel keys ................................ 93

Setting the FACTORY PRESET ............................ 94

Remote control features .......................................96

Setting remote control codes .................................. 96

Controlling other components ................................ 97

Using the TV macro ............................................. 100

Troubleshooting ..................................................102

Glossary ...............................................................105

Index ....................................................................107

Specifications ......................................................108

List of remote control codes...........................................i

Contents

INTRODUCTION

PREPARATION

SETUP

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

Overview

2 En

It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of

wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of

surround sound experience as your local movie theater.

Yamaha YSP-3000 Digital Sound Projector challenges this preconception that complicated speaker setup and

troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.

This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is

not only easy to set up, but is also capable of reproducing the kind of powerful surround sound you have been waiting for

from its built-in 2 woofers and 21 full-range small speakers.

You can fine-tune the parameters of this unit to adjust the delay time for separate sound beams, resulting in highly

directional sound that comes in on the listening position from all directions.

The YSP-3000 projects sound beams containing surround sound information for the front right (R), front left (L),

surround right (SR), and surround left (SL) speaker positions, which are reflected off the walls of your listening room

before reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector

creates true-to-life 5.1-channel surround sound that makes you feel as if there are actual speakers around the room.

Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.

Overview

SL

SR

R

L

C

Listening position

Imaginary

surround left

speaker

Imaginary

surround right

speaker

Imaginary

front left

speaker

Imaginary

front right

speaker

Imaginary

center

speaker

Features

3 En

INTRODUCTION

English

Digital Sound Projector™

The Digital Sound Projector technology allows one slim

unit to control and steer multiple channels of sound to

generate multi-channel surround sound, thus eliminates

the need for satellite loudspeakers and cabling normally

associated with conventional surround sound systems.

This unit also employs the beam modes that let you enjoy

the surround sound (5 Beam, Stereo plus 3 Beam, 3 Beam,

and My Surround), 2-channel and 5-channel stereo

playback, and My Beam.

My Surround

In addition to the above mentioned beam modes, this unit

is equipped with My Surround beam mode that allows you

to enjoy surround system even in a small listening area.

My Surround is a function integrated and optimized with

DiMAGIC’s Euphony technology and Yamaha’s Beam

reproduction system.

My Beam

This unit employs My Beam that ensures a clear sound in

a noisy environment. You can adjust the beam angle

manually or automatically using the supplied remote

control to the maximum of 45°, rightward and leftward.

Cinema DSP

This unit employs the Cinema DSP technology developed

by Yamaha Electronics Corp. that lets you experience

movies at home with all the original dramatic sound

impact.

HDMI™ (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced, or high-definition

video (including 1080p video signal transmission) as well as

multi-channel digital audio based on HDCP

◆ Simple and easy connections with HDMI supported external

components

◆ Functional link with an HDMI control-compatible TV

Versatile Remote Control

The supplied remote control comes with preset remote

control codes used to control the DVD player, VCR, cable

TV tuner, and digital satellite tuner connected to this unit.

In addition, the remote control is equipped with the macro

capability that enables a series of operations with the press

of a single button.

AUTO SETUP (IntelliBeam)

This unit employs the automatic sound beam and acoustic

optimization technology with the aid of the supplied

IntelliBeam microphone. You can avoid troublesome

listening-based speaker setup and achieve highly accurate

sound beam adjustments that best match your listening

environment.

Compatibility with the Newest Technologies

This unit employs decoders compatible with Dolby

Digital, DTS, Dolby Pro Logic, Dolby Pro Logic II, DTS

Neo:6, Music Enhancer, and Neural Surround.

◆ Dolby Digital

This is the standard audio signal format used on various

digital media such as DVD, Blu-ray, and HD DVD. This

surround technology delivers high-quality digital audio for up

to 5.1 discrete channels to produce a directional and more

realistic effect.

◆ DTS

This is the standard audio signal format used on various

digital media such as DVD, Blu-ray, and HD DVD. This

surround technology delivers high-quality digital audio for up

to 5.1 discrete channels to produce a directional and more

realistic effect.

◆ Dolby Pro Logic

This sophisticated, matrix decoding technology up-converts

any 2-channel source audio to a 5.1-channel full bandwidth

playback, resulting in a surround sound experience.

◆ Dolby Pro Logic II

This is a redesigned version of Dolby Pro Logic that employs

2 stereo surround channels, a subwoofer, and a greatly

enhanced steering logic. This improved technology provides

an exceptionally stable sound field that simulates 5.1 to a

much greater degree than the original Dolby Pro Logic.

◆ DTS Neo:6

This technology decodes the conventional 2-channel sources

for 6-channel playback, enabling playback with the full-range

channels with higher separation. Music mode and Cinema

mode are available to play back music and movie sources

respectively.

◆ Music Enhancer to restore the original depth and width of

compression artifacts such as the MP3 format.

◆ Neural Surround decoder (U.S.A and Canada models only)

Sophisticated FM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

◆ Radio Data System capability (Europe model only)

XM™ Satellite Radio

(U.S.A. and Canada models only)

◆ XM Satellite Radio tuning capability (using the XM Mini-

Tuner Dock, and Antenna sold separately by XM Satellite

Radio)

◆ Neural Surround decoder to play back the XM HD content of

XM Satellite Radio broadcasts in multi-channels, resulting in

a full surround sound experience

◆ XM Satellite Radio information displaying capability

iPod™ Controlling Capability

(U.S.A., Canada, and Australia models only)

◆ DOCK terminal to connect a Yamaha iPod universal dock

(such as the YDS-10, sold separately), which supports iPod

(Click and Wheel), iPod nano, and iPod mini

◆ Playback information displaying capability

◆ Battery charging capability

Features

4 En

The “ ” logo and “IntelliBeam” are trademarks of

YAMAHA Corporation.

The “ ” logo and “Cinema DSP” are registered

trademarks of YAMAHA Corporation.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS” and “Neo:6” are registered trademarks of DTS, Inc.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks or registered trademarks of HDMI

Licensing LLC.

Manufactured under license from 1 Ltd. Worldwide patents

applied for.

The “ ” logo and “Digital Sound Projector

™

” are trademarks

of 1 Ltd.

TruBass, SRS and the “ ” symbol are registered trademarks

of SRS Labs, Inc. TruBass technology is incorporated under

license from SRS Labs, Inc.

™

is a trademark of DiMAGIC Co., Ltd.

Using this manual

5 En

INTRODUCTION

English

• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the

supplied owner’s manual for each component.

• Operations in this manual use keys on the supplied remote control of this unit unless otherwise specified.

• y indicates a tip for your operation.

• This manual is printed prior to production. Designs and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and the product, the product has priority.

1 Install this unit in your listening room.

See “Installation” on page 16.

2 Connect this unit to your TV and other external components.

See “Connections” on page 19.

3 Prepare the remote control and turn on the power of this unit.

See “Getting started” on page 30.

4 Run AUTO SETUP.

See “AUTO SETUP (IntelliBeam)” on page 35.

5 Play back a source.

See “Playback” on page 45.

6 Change the beam modes and/or CINEMA DSP settings.

See “Enjoying surround sound” on page 54.

7 Run MANUAL SETUP to fine-tune settings and/or set remote control codes.

See “MANUAL SETUP” on page 72 and “Remote control features” on page 96.

Using this manual

Notes

If you want to make additional settings

and adjustments

Supplied accessories

6 En

Check that you have received all of the following parts.

Supplied accessories

Connecting external components such as a TV or DVD player to this unit.

Connect your TV or DVD player to this unit using appropriate cables as shown below. After all connections are complete, plug the power supply cable into the AC

wall outlet. For further information on connecting other components, see pages 19 to 29 in the Owner’s Manual.

YSP-3000

QUICK REFERENCE GUIDE

Printed in Malaysia

WK75520 [En]

1

2

AUDIO INPUT

OUT

AUX 1

TV/STB

SUBWOOFER

AUX 1

DVD

AUX 2

VIDEO

DIGITAL INPUT

COAXIAL

AUDIO OUTPUT

L

R

VIDEO

INPUT

ANALOG AUDIO

OUTPUT

OPTICAL

AUDIO OUTPUT

DVD player

TV

Decide where to install this unit.

Install this unit where there are no objects such as furniture obstructing the path of sound beams. Otherwise, the desired

surround sound effects may not be achieved. You may install this unit in parallel with the wall or in the corner.

YSP-3000

Connecting external components to this unit

Installing this unit

This quick reference guide explains steps to connect a TV and a DVD player to this unit and achieve the

surround sound effects in a quick, easy manner. For detailed operation, refer to the Owner’s Manual.

Install this unit using a rack, etc.

Depending on your installation environment, connections with external components (see “2 Connecting external components to this unit”) can be done before

installing this unit. We recommend that you temporarily place and arrange all components in order to decide which procedure must come first. In case you

install this unit on top of a rack, etc., use the supplied fasteners to prevent an accidental fall of this unit.

For further information on installation, see page 16 in the Owner’s Manual.

Install this unit in the exact center of the wall when it is

measured from the left and right corners.

Install this unit in the corner at a 40˚ to 50˚ angle from the

adjacent walls.

40˚ to 50˚

An object, such as furniture An object, such as furniture

To the AC wall

outlet

132

Pull out the cap

before connecting

the optical cable,

and then check the

direction to insert the

cable.

Do not plug the power

supply cable into an AC

wall outlet until all

connections are complete.

1

2

Items used for connections and operations

in this guide

s

Audio pin cable (x1)

s

OSD* video pin cable (x1)

s

Optical cable (x1)

s

Digital audio pin cable (x1)

s

IntelliBeam microphone (x1)

s

Cardboard microphone stand (x1)

s

Demonstration DVD (x1)

*OSD: On-Screen Display

Connection

example 1

1. Pull out the cap

2. Check the direction

If you have connected external components,

follow the steps on the backside to start the

AUTO SETUP procedure.

Continued

on the back

Front left channel

Center channel

Front right channel

Surround left channel

Surround right channel

Front left channel

Center channel

Front right channel

Surround left channel

Surround right channel

This connection example shows a way to connect external components such as a TV or DVD player to

this unit by using the supplied cable. You can enjoy the multi-channel audio from the DVD player and the

analog/digital audio from the TV. Use the video pin cable supplied with your DVD player to make a video

connection between your DVD player and TV.

1

2

VIDEO

INPUT

HDMI

INPUT

HDMI

OUTPUT

HDMI

OUT

IN

DVD

AUX 1

AUDIO INPUT

OUT

AUX 1

TV/STB

SUBWOOFER

AUX 1

DVD

AUX 2

VIDEO

DIGITAL INPUT

COAXIAL

1

To the AC wall

outlet

Connect cables in the following order.

3

Install this unit in the

rack.

1

Place this unit in front of

the rack.

This connection example shows a way to make the most of the capability of this unit. You can

enjoy DVD audio and video with higher quality via the HDMI cable. In case your TV does not have

a built-in digital satellite tuner, cable TV tuner, or digital airwave tuner, connect a digital satellite

tuner, cable TV tuner, or digital airwave tuner via the HDMI cable. For details, see “Connections

using HDMI cables” on page 21 in the Owner’s manual.

Connection

example 2

DVD player

TV

YSP-3000

Do not plug the power

supply cable into an AC

wall outlet until all

connections are complete.

If you have connected external components,

follow the steps on the backside to start the

AUTO SETUP procedure.

Continued

on the back

Supplied Sold separately

Connect cables in the following order.

1 OSD video pin cable

(Displaysthe YSP-3000 menu screen on the TV)

2 HDMI cable

(Displaysthe DVD digital video on the TV)

3 HDMI cable

(InputsDVD digital audio/video signals to this unit)

2

(Sold separately)

3

(Sold separately)

2

Place this unit upside

down and connect this unit to

your TV and DVD player.

y Hint

•To enjoy better surround effects, place this unit on the upper shelf to keep it away from the floor.

•You can also use the optional metal wall bracket (sold separately) to mount this unit on the wall. For details, refer to the instructions

supplied with the metal wall bracket.

Note

Be careful not to leave scratches on this unit or the rack.

Video connection

Supplied

1Audio pin cable

(OutputsTV analog audio sounds from this unit)

2 OSD video pin cable

(Displaysthe YSP-3000 menu screen on the TV)

3 Optical cable

(Outputs

TV digital audio sounds from this unit)

4 Digital audio pin cable

(OutputsDVD digital audio sounds from this unit)

*

The rear panel illustration shows jacks and their names to help you find them easily. They

are not exactly the same as the ones on the actual rear panel of this unit.

4

Installation is completed.

The following is an example of installing this unit in a rack. To prevent this unit or the floor from being scratched, we recommend putting a piece of

cloth on the floor in step 2.

y Hint

Check whether the digital audio output of your TV and DVD

player is turned on.

y Hint

•If you connect this unit to an HDMI control-compatible TV

(except some models) via HDMI, you can use the remote

control supplied with your TV to turn on or off the power,

select the audio output component, and adjust the volume

level of this unit.

•Check whether the digital audio output of your TV and DVD

player is turned on.

*

The rear panel illustration shows jacks and their names to help youfind them easily. They

are not exactly the same as the ones on the actual rear panel of this unit.

Digital satellite tuner/Cable TV tuner/

Digital airwave tuner

Audio connection

HDMI connection

Subwoofer

Optical cable

STEREO MY SUR.

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

SUR. DECODE

OFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

TV

INPUT1

YSP

TV/AV

CH

ENTRY

CAT/

A-E

4

6

321

AUX1 AUX2

STB

TV

DVD

AUX3

TV

POWERPOWERSTANDBY/ON

DOCK

+10

0

78

9

5

AV

Remote control (×1)

Batteries (×2)

(AA, R6, UM-3)

OSD* video pin cable (×1)

IntelliBeam microphone

(×1)

Fasteners (×4)

Audio pin cable (×1)

Digital audio pin cable (×1)

Optical cable (×1)

Cable clamp (×1)

Cardboard microphone

stand (×1)

(Orange)

(White/Red)

(Yellow)

Indoor FM antenna (×1)

(U.S.A. and Canada models)

Demonstration DVD

(×1)

YSP-3000

Digital Sound Projector

TM

Reference Guide for iPod/XM Radio

This is the Reference Guide for Yamaha YSP-3000 Digital Sound Projector. This guide explains the connections and

operations of iPod and XM Satellite Radio (U.S.A. and Canada models only). Operations in this guide use keys on the

supplied remote control unless otherwise specified. For general information including the controls and functions of this

unit, refer to the owner’s manual.

y

The illustrations used in this Reference Guide are for U.S.A. and Canada models only.

“iPod” is a trademark of Apple Inc., registered in the U.S. and other countries.

The XM name and related logos are registered trademarks of XM Satellite Radio Inc.

Neural Surround

™

name and related logos are trademarks owned by Neural Audio Corporation.

Using iPod™........................................................................................................................................ 2

Connection................................................................................................................................................. 2

Controlling iPod™ ....................................................................................................................................2

XM Satellite Radio tuning (U.S.A. and Canada models only)........................................................ 5

Connecting XM Mini-Tuner Home Dock................................................................................................. 5

Activating XM Satellite Radio.................................................................................................................. 6

Basic XM Satellite Radio operations........................................................................................................ 6

Presetting the XM Satellite Radio channels.............................................................................................. 9

Displaying the XM Satellite Radio information...................................................................................... 10

Troubleshooting................................................................................................................................ 11

Overview

Contents

iPod

TM

UA

REFERENCE GUIDE

(iPod/XM Radio) (×1)

QUICK REFERENCE

GUIDE

(U.S.A., Canada, and Australia

models only)

* The number of provided languages

varies depending on the sales area.

*OSD: On-Screen Display

Controls and functions

7 En

INTRODUCTION

English

1 AUX 3 input jack

Connect your portable audio player (see page 26).

2 INTELLIBEAM MIC jack

Connect the supplied IntelliBeam microphone for AUTO

SETUP (see page 36).

3 Remote control sensor

Receives infrared signals from the remote control.

4 Front panel display

Shows information about the operational status of this

unit.

5 INPUT

Press repeatedly to switch between input sources (see

page 45).

Outputs a test tone to experience the sound beam (see

page 91).

6 VOLUME +/–

Controls the volume level of all audio channels (see

page 47).

7 STANDBY/ON

Turns on the power of this unit or sets it to the standby

mode (see page 31).

• When you turn on this unit, you will hear a click sound

followed by the 4 to 5-second interval before sound

reproducing.

• In the standby mode, this unit consumes a small amount of

power in order to receive infrared signals from the remote

control or to search for HDMI signals.

Controls and functions

Front panel

3 4

5

6

STANDBY/ON

VOLUME

+

INPUT

7

INTELLIBEAM MIC

AUX 3

21

Notes

Controls and functions

8 En

1 HDMI indicator

Lights up when the signal of the selected input source is

input at the HDMI IN jack(s).

2 TUNER indicators

FM: Light up when this unit is receiving an FM broadcast.

XM: MEMORY flashes during the XM preset operation

(U.S.A. and Canada models only).

3 CINEMA DSP indicator

Lights up when a sound field program is selected (see

page 64).

4 PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code

Modulation) digital audio signals.

5 Decoder indicators

Light up when the corresponding decoder operates

(see page 56).

The neural decoder is available for the U.S.A. and Canada models

only.

6 ENHANCER indicator

Lights up when the Music Enhancer is selected (see

page 66).

7 Volume level indicator

Displays the current volume level.

8 DOCK indicator

(U.S.A., Canada, and Australia models only)

Lights up when your iPod (Click and Wheel), iPod nano,

or iPod mini is connected to this unit via the DOCK

terminal on this unit.

9 SRS TruBass indicator

Lights up when TruBass is turned on (see page 79).

0 EQUAL indicator

Lights up when the TV volume equal mode is selected

(see page 67).

A NIGHT indicator

Lights up when one of the night listening enhancers is

selected (see page 67).

B SLEEP indicator

Lights up when the sleep timer is set (see page 68).

C Radio Data System indicators

(Europe model only)

Show the current Radio Data System status.

D XM indicator

(U.S.A. and Canada models only)

Lights up when XM is selected as the input source.

E Multi-information display

Shows information with alphanumeric characters when

you adjust the parameters of this unit.

F Input channel indicators

Show information when you adjust the parameters of this

unit. The channel component of the current digital input

signal is displayed (see page 56).

y

You can adjust the brightness and display setting of the front

panel display using the F.DISPLAY SET parameter in MANUAL

SETUP (see page 83).

Front panel display

1

89

0

23

4

67

5

AB C D

EF

Note

Controls and functions

9 En

INTRODUCTION

English

The illustration below shows the rear panel of the U.S.A. and Canada models.

1 ANTENNA jack

Connect the FM antenna (see page 29).

2 DOCK terminal

(U.S.A., Canada, and Australia models only)

Connect the Yamaha iPod universal dock (such as YDS-

10, sold separately) (see page 2 in the Reference Guide).

3 AUX 1 AUDIO INPUT jacks

Connect an external component via an analog connection

(see page 23).

4 TV/STB AUDIO INPUT jacks

Connect your TV, digital satellite tuner, or cable TV tuner

via an analog connection (see pages 22 and 24).

5 VIDEO OUT jack

Connect to the video input jack of your TV to display the

OSD of this unit (see page 22).

6 SUBWOOFER OUT jack

Connect your subwoofer (see page 28).

7 AUX 2 COAXIAL DIGITAL INPUT jack

Connect an external component via a coaxial digital

connection (see page 27).

8 AUX 1 OPTICAL DIGITAL INPUT jack

Connect an external component via an optical digital

connection (see page 27).

9 TV/STB OPTICAL DIGITAL INPUT jack

Connect your TV, digital satellite tuner, or cable TV tuner

via an optical digital connection (see pages 22 and 24).

0 DVD COAXIAL DIGITAL INPUT jack

Connect your DVD player via a coaxial digital connection

(see page 23).

A XM antenna jack

(U.S.A and Canada models only)

Connect your XM Mini-Tuner Dock (sold separately)

(see page 5 in the Reference Guide).

B IR IN terminal

(U.S.A and Canada models only)

This is a control expansion terminal for commercial use

only (see page 29).

C AUX 1 HDMI IN jack

Connect your digital satellite tuner, cable TV tuner, digital

air wave tuner, or game console via an HDMI connection

(see page 21).

D DVD HDMI IN jack

Connect your DVD player via an HDMI connection (see

page 21).

E HDMI OUT jack

Connect to the HDMI IN jack on your HDMI component

such as a TV or a projector connected to this unit (see

page 21).

F AC power supply cable

Connect to the AC wall outlet (see page 29).

Rear panel

DIGITAL INPUTOUT

TV/STB

DVD

SUBWOOFER

IR INXM

AUX 1

DVD

IN

OUT

HDMI

TV/STB

AUX 1 AUX 1

AUX 2

COAXIAL

OPTICAL

VIDEO

DOCK

AUDIO INPUTANTENNA

8

90

A

B

C

D

E

1

2

3

4

5

6

7

F

(U.S.A. and Canada models)

Controls and functions

10 En

This section describes the functions of the remote control

used to control this unit. Some buttons marked with an

asterisk (*) share the common functions between the YSP

and TV/AV operation modes (S).

y

You can also control other components using the remote control

once you set the appropriate remote control codes. See

“Controlling other components” on page 97 for details.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 STANDBY/ON

Sets this system to the standby mode (see page 31).

3 Transmission indicator

Lights up when infrared control signals are being output.

4 Input selector buttons

Use to select an input source (DVD, AUX1, AUX2,

AUX3, STB, TV, or FM).

5 VOL MODE

Turns on or off the volume modes (see page 67).

6 AUTO SETUP

Enters the AUTO SETUP menu (see page 35).

7 CINEMA DSP program buttons

Select the CINEMA DSP programs (see page 63).

8 ENHANCER

Turns on or off the Music Enhancer (see page 66).

9 Cursor buttons / / / , ENTER

Select and adjust SET MENU items.

0 DISPLAY

Displays information on the selected input signal.

A VOLUME +/–

Increases or decreases the volume level of this unit (see

page 47).

B MUTE

Mutes the sound. Press again to restore the audio output to

the previous volume level (see page 47).

C TV INPUT

Toggles between the input sources on the TV (see

page 97).

D CH LEVEL

Adjusts the volume level of each channel (see page 85).

E TEST

Outputs a test tone when adjusting the output level of each

channel (see page 84).

Remote control (Europe, Australia, Asia, and Korea models)

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

SUR. DECODE

OFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

A-E

MACRO

TV

INPUT1

YSP

TV/AV

CH

ENTRY

A-E

4

6

321

AUX1 AUX2

STB

FM

TV

DVD

AUX3

TVAV

POWERPOWERSTANDBY/ON

+10

0

78

9

5

MY SUR.

1G

H

I

J

K

L

M

N

O

P

Q

R

S

t

U

V

W

2

3

4

5

6

7

8

9

0

A

B

C

D

E

F

*

Controls and functions

11 En

INTRODUCTION

English

F DVD player/VCR control buttons

Control your DVD player or VCR (see pages 98 and 99).

G My Beam microphone

Collects the test tones from this unit when using the My

Beam auto-adjust function (see page 61).

H TV POWER

Turns on the power of your TV or sets it to the standby

mode (see page 97).

I AV POWER

Turns on the power of the selected component or sets it to

the standby mode (see pages 98 and 99).

J INPUT1

Switches the input source on your TV (see page 97).

K MACRO

Use to set the TV macro (see page 100).

L a/5

Switches the preset station number (1 to 8) when this unit

is receiving an FM broadcast (see page 52).

M A-E

Switches the preset station group (A to E) when this unit is

receiving an FM broadcast (see page 52).

N SLEEP

Sets the sleep timer (see page 68).

O INPUTMODE

Toggles between input modes (AUTO, DTS, and

ANALOG) (see page 87).

P Beam mode buttons

Change the beam mode settings (see pages 54, 60, and

61).

Q SUR. DECODE

Selects the surround mode for playback (see page 57).

R MENU

Displays the setup menu on your TV monitor (see

pages 37 and 73).

S Operation mode selector

Selects the operation mode of this unit. Select YSP when

operating this unit and select TV/AV when operating your

TV or other AV components.

T RETURN

Selects sleep timer settings or returns to the previous SET

MENU screen.

U TV VOL +/–

Adjusts the volume level of your TV (see page 97).

V CH +/–

Changes the channels of your TV, digital satellite tuner,

cable TV tuner, or VCR (see pages 97 and 99).

W TV MUTE, CODE SET

Mutes the audio output of your TV (see page 97).

Sets up remote control codes (see page 96).

The functions L and M are available only when the FM stations

are preset.

Note

Controls and functions

12 En

This section describes the functions of the remote control

used to control FM, Radio Data System, or iPod when the

TV/AV mode is selected with the operation mode selector

(7). Note that the Radio Data System controls are

available for Europe model only, and the iPod controls are

available for Australia model only.

1 PRESET/TUNE

FM: Switches between the preset search mode and the

frequency search mode (see pages 49 to 52).

2 Numeric buttons

FM: Enter numbers.

3 Cursor buttons / / / , ENTER

FM: Use ENTRY ( / ) to change the preset station

number (1 to 8) or frequency level (see pages 49 to 52).

Use A-E ( / ) to change the preset station group (A to

E) (see pages 51 and 52). Use ENTER to confirm the input

above.

y

These functions are also available when this unit is receiving the

Radio Data System (see page 52) or playing back your iPod (see

page 3 in the Reference Guide).

4 DISPLAY

Radio Data System and iPod: Displays information when

this unit is receiving the Radio Data System (see page 52)

or playing back your iPod (see page 3 in the Reference

Guide).

5 MEMORY

FM: Stores the preset stations (see pages 50 and 51).

y

This function is also available when this unit is receiving the

Radio Data System (see page 52).

6 SEARCH

FM: Switches between automatic and manual tuning (see

page 49).

7 Operation mode selector

Selects the operation mode of this unit. Select YSP when

operating this unit and select TV/AV when operating your

TV or other AV components.

4

6

321

+10

0

78

9

5

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

OFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

A-E

MACRO

TV

INPUT1

YSP

TV/AV

CH

ENTRY

A-E

AUX1 AUX2

STB

FM

TV

DVD

AUX3

TVAV

POWERPOWERSTANDBY/ON

ENTER

SUR. DECODE

MY SUR.

1

2

3

4

5

6

7

Controls and functions

13 En

INTRODUCTION

English

This section describes the functions of the remote control

used to control this unit. Some buttons marked with an

asterisk (*) share the common functions between the YSP

and TV/AV operation modes (S).

y

You can also control other components using the remote control

once you set the appropriate remote control codes. See

“Controlling other components” on page 97 for details.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 STANDBY/ON

Sets this system to the standby mode (see page 31).

3 Transmission indicator

Lights up when infrared control signals are being output.

4 Input selector buttons

Use to select an input source (DVD, AUX1, AUX2,

AUX3/DOCK, STB, TV, or FM/XM).

5 VOL MODE

Turns on or off the volume modes (see page 67).

6 AUTO SETUP

Enters the AUTO SETUP menu (see page 35).

7 Sound field program buttons

Select the sound field programs (see page 63).

8 ENHANCER

Turns on or off the Music Enhancer (see page 66).

9 Cursor buttons / / / , ENTER

Select and adjust SET MENU items.

0 DISPLAY

Displays information on the selected input signal.

A VOLUME +/–

Increases or decreases the volume level of this unit (see

page 47).

B MUTE

Mutes the sound. Press again to restore the audio output to

the previous volume level (see page 47).

C TV INPUT

Toggles between the input source on your TV (see

page 97).

D CH LEVEL

Adjusts the volume level of each channel (see page 85).

E TEST

Outputs a test tone when adjusting the output level of each

channel (see page 84).

Remote control (U.S.A. and Canada models)

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

OFF

CODE SET

SPORTS

5BEAM ST+3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

TV

INPUT1

YSP

TV/AV

CH

ENTRY

CAT/

A-E

4

6

321

AUX1 AUX2

STB

TV

DVD

AUX3

TV

POWERPOWERSTANDBY/ON

DOCK

+10

0

78

9

5

AV

MY SUR.

3BEAM

SUR. DECODE

1G

H

I

J

K

L

M

N

O

P

Q

R

S

t

U

V

W

2

3

4

5

6

7

8

9

0

A

B

C

D

E

F

*

Controls and functions

14 En

F DVD player/VCR control buttons

Control your DVD player or VCR (see pages 98 and 99).

G My Beam microphone

Collects the test tones from this unit when using the My

Beam auto-adjust function (see page 61).

H TV POWER

Turns on the power of your TV or sets it to the standby

mode (see page 97).

I AV POWER

Turns on the power of the selected component or sets it to

the standby mode (see pages 98 and 99).

J INPUT1

Switches the input source on your TV (see page 97).

K MACRO

Use to set the TV macro (see page 100).

L a/5

Switches the preset station number (1 to 8) when this unit

is receiving an FM broadcast or XM channel (see

page 52).

M CAT

Switches the preset station group (A to E) when this unit is

receiving an FM broadcast or XM channel (see page 52).

N SLEEP

Sets the sleep timer (see page 68).

O INPUTMODE

Toggles between input modes (AUTO, DTS, and

ANALOG) (see page 87).

P Beam mode buttons

Change the beam mode settings (see pages 54, 60, and

61).

Q SUR. DECODE

Selects the surround mode for playback (see page 57).

R MENU

Displays the setup menu on your TV monitor (see

pages 37 and 73).

S Operation mode selector

Selects the operation mode of this unit. Select YSP when

operating this unit and select TV/AV when operating your

TV or other AV components.

T RETURN

Selects sleep timer settings or returns to the previous SET

MENU screen.

U TV VOL +/–

Adjusts the volume level of your TV (see page 97).

V CH +/–

Changes the channels of your TV, digital satellite tuner,

cable TV tuner, or VCR (see pages 97 and 99).

W TV MUTE, CODE SET

Mutes the audio output of your TV (see page 97).

Sets up remote control codes (see page 96).

The functions L and M are available only when the FM/XM

stations are preset.

Note

Controls and functions

15 En

INTRODUCTION

English

This section describes the functions of the remote control

used to control FM, XM Satellite Radio, or iPod when the

TV/AV mode is selected with the operation mode selector

(7).

1 PRESET/TUNE

FM: Switches between the preset search mode and the

frequency search mode (see pages 49 to 52).

2 Numeric buttons

FM, XM: Enter numbers.

3 Cursor buttons / / / , ENTER

FM: Use ENTRY ( / ) to change the preset station

number (1 to 8) or frequency level (see pages 49 to 52).

Use CAT/A-E ( / ) to change the preset station group

(A to E) (see pages 51 and 52). Use ENTER to confirm the

input above.

XM: Use ENTRY ( / ) to select XM channels in

All Channel Search mode/Category Search mode, and to

select the preset channel number (1 to 8) in Preset Search

mode. Use CAT/A-E ( / ) to select XM categories in

All Channel Search mode/Category Search mode, and to

select the preset channel group (A to E) in Preset Search

mode. Use ENTER to confirm the input above (see pages

7 and 8 in the Reference Guide).

y

These functions are also available when this unit is playing back

your iPod (see page 3 in the Reference Guide).

4 DISPLAY

XM and iPod: Displays information when this unit is

receiving an XM channel (see page 10 in the Reference

Guide) or playing back your iPod (see page 3 in the

Reference Guide).

5 MEMORY

FM: Stores the preset stations (see pages 50 and 51).

XM: Use to store the preset stations (see page 9 in the

Reference Guide).

6 SEARCH

FM: Switches between automatic and manual tuning (see

page 49).

XM: Switches between search modes (All Channel

Search, Category Search, and Preset Search) (see pages 7

and 8 in the Reference Guide).

7 Operation mode selector

Selects the operation mode of this unit. Select YSP when

operating this unit and select TV/AV when operating your

TV or other AV components.

4

6

321

+10

0

78

9

5

STEREO

MY BEAM

PRESET/TUNE

MEMORYSEARCH

SLEEP

INPUTMODE

ENHANCER MENU

RETURNDISPLAY

TV VOL

VOLUME

MUTE

CH LEVEL TEST

TV INPUT TV MUTE

ENTER

OFF

CODE SET

SPORTS

5BEAM ST+3BEAM 3BEAM

MUSIC MOVIE

VOL MODE

AUTO

SETUP

CATFM/XM

MACRO

TV

INPUT1

CH

ENTRY

CAT/

A-E

AUX1 AUX2

STB

TV

DVD

AUX3

TV

POWERPOWERSTANDBY/ON

DOCK

AV

YSP

TV/AV

SUR. DECODE

MY SUR.

1

2

3

4

5

6

7

Installation

16 En

This section describes a suitable installation location to install this unit using a metal wall bracket, a rack or a stand.

Depending on your installation environment, connections with external components can be done before installing this

unit. We recommend that you temporarily place and arrange all components, including this unit, in order to decide which

procedure should come first. Especially when you make a connection over HDMI, we recommend that you make a

connection first before installation (see page 21).

This unit creates surround sound by reflecting projected

sound beams off the walls of your listening room. The

surround sound effects produced by this unit may not be

sufficient when this unit is installed in the following

locations.

• Rooms with walls inadequate for reflecting sound

beams

• Rooms with acoustically absorbent walls

• Rooms with measurements outside the following

range: W (3 to 7 m (10 to 23 ft)) x H (2 to 3.5 m (7 to

11.5 ft)) x D (3 to 7 m (10 to 23 ft))

• Rooms with less than 1.8 m (6 ft) from the listening

position to this unit

• Rooms where objects such as furniture are likely to

obstruct the path of sound beams

• Rooms where the listening position is close to the walls

• Rooms where the listening position is not in front of

this unit

y

• You can enjoy surround sound by selecting My Surround (see

page 55) as the beam mode even if your listening room may not

fulfill the above conditions (except when the listening position

is not directly facing toward the front of this unit).

• You can also enjoy surround sound by selecting 2-channel or 5-

channel stereo playback (see page 60) or My Beam (see

page 61) as the beam mode even if your listening room may not

fulfill the above conditions.

Make sure you leave an adequate amount of ventilation

space so that heat can escape. Make at least 5 cm (2 in) of

space above or below this unit.

• We do not recommend putting this unit directly on the floor of

your listening room. Please install this unit using a metal wall

bracket, a rack, or a stand.

• This unit weighs 11.5 kg (25 lbs 6 oz). Be sure to install this

unit where it will not fall subject to vibrations, such as from an

earthquake, and where it is out of the reach of children.

• When using a cathode-ray tube (CRT) TV, do not install this

unit directly above your TV.

• This unit is shielded against magnetic rays. However, if the

picture on your TV screen becomes blurred or distorted, we

recommend moving this unit away from your TV.

Install this unit where there are no obstacles such as

furniture obstructing the path of sound beams. Otherwise,

the desired surround sound effects may not be achieved.

You may install this unit in parallel with the wall or in the

corner.

Parallel installation

Install this unit in the exact center of the wall when it is

measured from the left and right corners.

Corner installation

Install this unit in the corner at a 40º to 50º angle from the

adjacent walls.

Installation

Before installing this unit

5 cm (2 in) or more

Rear

Front

Side view

Notes

Installing this unit

An object, such as furniture

40° to 50°

An object, such as furniture

Страница загружается ...

Yamaha YSP-3000 Инструкция по применению

Это руководство также подходит для

Yamaha YSP-3000 Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов