YSP-1
Digital Sound Projector
OWNER'S MANUAL
UBTK
01EN_YSP-1_UB-cv1.fm Page 1 Friday, November 12, 2004 6:36 PM
i CAUTION
* Explanation of Graphical Symbols
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10 Protect the power cable from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
C
AU
T
I
O
N
CAUTION ii
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void
your authority, granted by the FCC, to use the product.
2. IMPORTANT :
When connecting this product to accessories and/or another
product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
3. NOTE :
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equip-
ment by playing it at a safe level. One that lets the sound come
through loud and clear without annoying blaring or distortion –
and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid pro-
longed exposure from excessive volume levels.
iii CAUTION
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place with at least 5 cm of space above (or below) YSP-1 – away
from direct sunlight, heat sources, vibration, dust, moisture, and/
or cold.
3 Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in an environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
7 Do not plug in this unit to a wall outlet until all connections are
complete.
8 Do not operate this unit upside-down. It may overheat, possibly
causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. YAMAHA will
not be held responsible for any damage resulting from use of this
unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the power cable from
the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed.
The cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
17 Before moving this unit, press STANDBY/ON to set this unit in
standby mode, and disconnect the AC power plug from the wall
outlet.
18 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave the unit alone.
19 When using the unit for a long time, the unit may become warm.
Turn the power off, then leave the unit alone for cooling.
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special instructions for U.K. model
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit itself
is turned off. This state is called the standby mode. In this
state, this unit is designed to consume a very small quantity of
power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide
slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear or the bottom of
this unit.
Retain this Owner’s Manual in a safe place for future
reference.
Note
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this appa-
ratus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to
the terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L
or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
CAUTION iv
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
v
Check that you have received all of the supplied accessories.
(See “Supplied accessories” on page 4.)
Install this unit in your listening room.
(See “INSTALLING THIS UNIT IN YOUR LISTENING ROOM” on page 9.)
Connect this unit to your TV and other external components.
(See “CONNECTIONS” on page 11.)
Prepare the remote control and turn on this unit.
(See “PREPARING THE REMOTE CONTROL” on page 18 and “BASIC OPERATION” on page 19.)
Follow the steps to enjoying surround sound or make EASY SETUP settings.
(See “STEPS TO ENJOYING SURROUND SOUND” on page 20 or “EASY SETUP” on page 24.)
Play back a source and adjust the beam mode settings.
(See “PLAYBACK” on page 31 and “ADJUSTING BEAM MODE SETTINGS” on page 34.)
To make additional settings and adjustments:
Make MANUAL SETUP settings and set remote control codes.
(See “MANUAL SETUP” on page 36 and “REMOTE CONTROL FEATURES” on page 51.)
HOW TO USE THIS MANUAL
1
PREPARATIONINTRODUCTION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
OVERVIEW ........................................................... 2
Selecting a listening room ......................................... 4
About this manual...................................................... 4
Supplied accessories .................................................. 4
CONTROLS AND FUNCTIONS ......................... 5
Front panel ................................................................. 5
Front panel display .................................................... 6
Bottom panel.............................................................. 7
Remote control........................................................... 8
INSTALLING THIS UNIT IN YOUR
LISTENING ROOM .......................................... 9
Choosing an installation location............................... 9
Using a metal wall bracket ...................................... 10
Using a stand............................................................ 10
Using a rack ............................................................. 10
Affixing this unit...................................................... 10
CONNECTIONS .................................................. 11
Connecting a TV...................................................... 12
Connecting a DVD player/recorder ......................... 13
Connecting a VCR................................................... 14
Connecting other external components ................... 15
Connecting a subwoofer .......................................... 16
Connecting the power supply cable......................... 17
About the RS-232C terminal ................................... 17
PREPARING THE REMOTE CONTROL ....... 18
Installing batteries in the remote control ................. 18
BASIC OPERATION........................................... 19
Using the remote control ......................................... 19
Turning the power on/to standby mode................... 19
STEPS TO ENJOYING SURROUND
SOUND
.................................................................. 20
Displaying the on-screen display (OSD) ................. 20
Selecting a preset listening environment ................. 21
Enjoying TV in surround sound .............................. 22
EASY SETUP........................................................ 24
Using EASY SETUP ............................................... 24
VOLUME CONTROLS....................................... 30
Adjusting the volume............................................... 30
Muting the sound ..................................................... 30
PLAYBACK.......................................................... 31
Selecting an input source......................................... 31
Playing back sources................................................ 31
SELECTING A SURROUND MODE................ 32
Playback sources and their available surround
modes................................................................... 32
Enjoying 2-channel sources with multi channels .... 32
Surround mode parameters ...................................... 33
ADDITIONAL PLAYBACK MODES ............... 33
Night listening modes.............................................. 33
ADJUSTING BEAM MODE SETTINGS.......... 34
Stereo mode ............................................................. 34
3 beam mode............................................................ 34
5 beam mode............................................................ 34
ST(STEREO)+3 beam mode ................................... 35
MANUAL SETUP .................................................36
Using SET MENU................................................... 37
SOUND MENU....................................................... 38
BEAM MENU......................................................... 40
INPUT MENU......................................................... 44
OPTION MENU...................................................... 45
SELECTING AN INPUT MODE........................47
MANUALLY ADJUSTING OUTPUT
LEVELS .............................................................48
Using the test tone ................................................... 48
Adjusting output levels during playback ................. 49
USING THE SLEEP TIMER ..............................50
REMOTE CONTROL FEATURES ...................51
Setting remote control codes ................................... 51
Controlling other components ................................. 52
TROUBLESHOOTING .......................................54
RESETTING THE FACTORY PRESETS ........57
FRONT PANEL DISPLAY ITEMS ....................58
GLOSSARY ...........................................................59
Audio formats .......................................................... 59
Audio information ................................................... 59
INDEX ....................................................................60
SPECIFICATIONS...............................................61
CONTENTS
INTRODUCTION
PREPARATION
BASIC OPERATION
ADVANCED OPERATION
ADDITIONAL INFORMATION
OVERVIEW
2
It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of
wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of
surround sound experience as your local movie theater.
YAMAHA’s YSP-1 Digital Sound Projector challenges this preconception that complicated speaker set up and
troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.
OVERVIEW
SL
SR
L
R
C
Listening
Position
Sound Beam Diagram
Imaginary front speaker position
Imaginary surround speaker position
OVERVIEW
3
INTRODUCTION
This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is
not only easy to set up, but which is also capable of reproducing the kind of powerful surround sound you have been
waiting for from its built-in subwoofers (2) and individual speakers (40).
You can use this unit’s parameters to fine tune the delay time for separate sound beams, resulting in highly directional
sound that comes in on the listening position from all directions.
The YSP-1 projects sound beams containing surround sound information for the front right (R), front left (L), surround
right (SR) and surround left (SL) speaker positions, which are reflected off the walls of your listening room before
reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector creates
true-to-life 5.1 channel surround sound that makes you feel as if there are actual speakers around the room.
Further, you can change the way in which these beams are projected at your walls (the beam mode) to match the contents
of the program you are watching or your listening environment, giving you a virtual surround sound experience for both
stereo and 5.1-channel playback.
This unit’s SET MENU can be displayed on your TV screen, allowing you to customize this unit to suit your listening
environment. Set up is straight forward using the MEMORY or EASY SETUP menus. MEMORY allows you to load
preset listening environment parameters for quick setup. EASY SETUP is an easy-to-follow setup method for first-time
users. In addition, the MANUAL SETUP menu offers advanced parameters for the surround sound enthusiast who wants
to make individual adjustments for each speaker position.
This highly-advanced projector supports a wide range of sound technology, including Dolby Digital, a basic audio format
for DVDs, Dolby Pro Logic for the reproduction of true-to-life sound, and DTS for playback of the best possible sound
clarity.
Equipped with two optical digital, one coaxial digital and two analog input jacks, the YSP-1 allows you to expand your
system through the direct connection of external components, such as a DVD player.
Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.
OVERVIEW
4
This unit creates surround sound by reflecting projected sound beams off the walls of your listening room. The surround
sound effects produced by this unit may not be sufficient when the unit is installed in the following locations:
• Rooms with surfaces inadequate for reflecting sound beams
• Rooms with acoustically absorbent surfaces
• Rooms with measurements outside the range: (3 to 7 m) × (2 to 3.5 m) × (3 to 7 m) (W × H × D)
• Rooms with less than 2 m from the listening position to the speaker positions
• Rooms where objects such as furniture are likely to obstruct the path of sound beams
• This manual describes how to connect and operate the YSP-1. For details regarding the operation of external
components, refer to the supplied owner’s manual for the component.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In such cases,
the operation is described using remote control operation.
• y indicates a tip for your operation.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of
improvements, etc. In case of differences between the manual and product, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
“DTS”, and “Neo:6” are trademarks of Digital Theater Systems,
Inc.
Manufactured under license from 1 Ltd. world-wide patents
applied for.
The “ ” logo and “Digital Sound Projector” are trademarks of
1 Ltd.
Please check that you received all of the following parts.
Selecting a listening room
About this manual
Supplied accessories
AV
POWER
2341
6785
0+109
CH
CODE SET
CH LEVEL MENU
RETURN
TEST
TV VOL
VOLUM E
MUTE
TV MUTE
TV INPUT TV DVD
AUX
BEAM MODE
SELECT
STANDBY/ON
SET MENU
SURROUND
VCRSLEEP
NIGHT
Remote control (×1)
Batteries (×2)
(AA, R6, UM-3)
OSD Video Cable (×1)
Power Cable (×1)
Cable Holder (×1)
Fastener (×4)
Audio Pin Cable (×1)
Digital Audio Pin Cable (×1)
Optical Cable (×1)
CONTROLS AND FUNCTIONS
5
INTRODUCTION
1 Front panel display
Shows information about the operational status of this
unit.
2 Remote control sensor
Receives signals from the remote control.
3 INPUT
Switches between the connected external audio sources.
4 VOLUME –/+
Controls the output level of all audio channels (see
page 30).
5 STANDBY/ON
Turns on this unit or sets it in the standby mode (see
page 19). When you turn on this unit, you will hear a click
and there will be a 4 to 5-second delay before it can
reproduce sound.
In standby mode, this unit consumes a small amount of power in
order to receive infrared-signals from the remote control.
CONTROLS AND FUNCTIONS
Front panel
+
STANDBY/ONVOLUME
+
INPUT
3 4
5
1
2
Note
CONTROLS AND FUNCTIONS
6
1 NIGHT indicator
Lights up when you select a night listening mode (see
page 33).
2 SLEEP indicator
Lights up while the sleep timer is on (see page 50).
3 Decoder indicators
When any of this unit’s decoders function, the respective
indicator lights up.
4 Volume level indication
Indicates the current volume level (see page 30).
5 Multi-information display
Shows information when adjusting or changing settings.
Front panel display
NIGHT SLEEP PCM PL
m
ft
mS
dB
VOL
DIGITAL
5
412 3
CONTROLS AND FUNCTIONS
7
INTRODUCTION
1 SYSTEM CONNECTOR jack
Use to connect a YAMAHA subwoofer equipped with a
SYSTEM CONNECTOR jack to this unit (see page 16).
2 RS-232C terminal
This is a control expansion terminal for commercial use
only (see page 17).
3 DVD coaxial digital input jack
Use to connect a DVD player using a coaxial digital
connection (see page 13).
4 AUX optical digital input jack
Use to connect an external component using an optical
digital connection (see page 15).
5 TV optical digital input jack
Use to connect a TV using an optical digital connection
(see page 12).
6 VIDEO OUT jack
Connect to your TV’s video input terminal to display this
unit’s OSD (see page 12).
7 SUBWOOFER OUT jack
Use to connect a subwoofer (see page 16).
8 TV analog audio input jacks
Use to make an analog connection to your TV
(see page 12).
9 VCR analog audio input jacks
Use to make an analog connection to your VCR
(see page 14).
0 AC IN
Connect the supplied power cable (see page 17).
Bottom panel
SYSTEM
CONNECTOR
VIDEO
OUT
SUBWOOFER
OUT
RS-232C COAXIAL
DVD AUX TV TV VCR
OPTICAL R L R L
DIGITAL INPUT
AUDIO INPUT
7
8
9342
5
6
1
0
CONTROLS AND FUNCTIONS
8
This section describes the function of each control on the
remote control used to control this system. To operate
other components, see “Controlling other components” on
page 52.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 STANDBY/ON
Sets this system in the standby mode (see page 19).
3 Numeric buttons
Use to enter numbers.
4 NIGHT
Turns on or off the night listening modes (see page 33).
5 SURROUND
Selects the surround mode for playback (see page 32).
6 Cursor buttons / / / SELECT
Use to select and adjust SET MENU items.
7 TEST
Outputs a test tone when adjusting the speaker levels
(see page 48).
8 MUTE
Mutes the sound (see page 30). Press again to restore the
audio output to the previous volume level.
9 SLEEP
Sets the sleep timer (see page 50).
0 Beam mode buttons
Change the beam mode settings (see page 34).
A CODE SET
Use to set up remote control codes (see page 51).
B SET MENU
Displays the SET MENU on your TV or monitor
(see page 24).
C RETURN
Use to select sleep timer settings (see page 50) or return to
the previous SET MENU screen (see page 24).
D VOLUME +/–
Increases or decreases this system’s volume level
(see page 30).
E Input selector buttons
Use to select a playback source and change the control
area (see page 31).
Remote control
AV
POWER
2341
6785
0 +109
CH
CODE SET
CH LEVEL MENU
RETURN
TEST
TV VOL
VOLUME
MUTE
TV MUTE
TV INPUT TV DVD
AUX
BEAM MODE
SELECT
STANDBY/ON
SET MENU
SURROUND
VCRSLEEP
NIGHT
1
2
3
4
5
6
7
8
9
0
A
B
C
D
E
INSTALLING THIS UNIT IN YOUR LISTENING ROOM
9
PREPARATION
This section describes how to choose a suitable installation location for this unit, and how to install the unit using either a
metal wall bracket, rack or stand.
If objects such as furniture are obstructing the path of sound beams, the desired surround sound effects may not be achieved. Make sure
you install this unit where there are no objects in the path of sound beams.
■ Notes on installation
• When installing this unit, be sure to leave an adequate
amount of ventilation space so that heat can escape.
Make sure you leave at least 5 cm of space above
(or below) this unit (as shown in the illustration on the
right).
• We do not recommend installing this unit so that it is
positioned directly on the floor of your listening room.
Please install this unit using a metal wall bracket, rack
or stand.
• This unit weighs 13 kg (28lbs). Be sure to install this
unit where it will not fall if subject to vibrations, such
as from an earthquake, and where it is out of the reach
of children.
• When using a cathode-ray tube (CRT) TV, do not
install this unit directly above your TV.
• This unit is shielded against magnetic rays. However,
if the picture on your TV screen becomes blurred or
distorted, we recommend moving the speakers away
from your TV.
To experience the best surround sound this unit can deliver, make sure you install this unit in a location where objects,
such as furniture, are not in the direct path of the sound beams (see the illustration below).
When installing this unit parallel to the wall, try placing it so that it is in the exact center of the wall (measured from the
left and right corners).
When installing this unit in the corner of your listening room, make sure the speakers are placed between 40º to 50º from
the adjacent walls.
INSTALLING THIS UNIT IN YOUR LISTENING ROOM
Note
Choosing an installation location
5 cm or
more
Rear
Front
40° to 50°
An object, such as furniture
10
INSTALLING THIS UNIT IN YOUR LISTENING ROOM
You can use the optional metal wall bracket to mount this
system on your listening room wall.
For details on how to attach the metal bracket to the wall
or how to attach this system to the metal bracket, refer to
the instructions supplied with the bracket.
You can mount your TV on the stand placed on a
commercially available rack to install this unit under your
TV.
For details on how to attach the stand or how to attach this
system to your TV, refer to the instructions supplied with
the stand.
You can install this system either above or under your TV
in a commercially available rack.
Before installing, make sure that the rack is large enough
to allow adequate ventilation space around this unit, and
that it is strong enough to support the weight of both this
unit and your TV.
To affix this unit, remove the protection pads from the
bottom of the unit, then secure the supplied fasteners (4
pieces) to the bottom four corners of this unit and the top
of the rack, etc. as shown below.
• Do not install this unit on top of a slanted surface. This unit may
fall over and cause injury.
• Make sure you wipe the surface of the rack, etc. before securing
the fasteners. Appling the tape to a dirty or wet surface will
weaken the sticking power of the tape, and this unit may fall as
a result.
Using a metal wall bracket
Using a stand
YSP-1
TV
Metal wall bracket
TV
YSP-1
Stand
Using a rack
Affixing this unit
Notes
TV
When the YSP-1 is
installed above your TV
When the YSP-1 is
installed under your TV
YSP-1
Remove the
protection
pads
Peel off
the film
Fasteners
CONNECTIONS
11
PREPARATION
This unit is equipped with two optical digital jacks, one coaxial digital jack and two types of analog jacks for connecting
external components such as your TV, DVD player, VCR and game console. Further, by connecting a subwoofer to this
unit, you can enjoy reinforced low bass sounds. For details on how to connect the various types of external components to
this unit, see pages 12 to 17.
Do not connect this unit or other components to the mains power until all connections between components are complete.
CONNECTIONS
CAUTION
Audio connection
Video connection
DVD player
Subwoofer
YSP-1
VCR
Digital satellite tuner, cable TV or
game console
TV
12
CONNECTIONS
You can connect a TV to this unit and display the OSD for easy viewing (see page 20) when operating SET MENU (see
page 24). When connecting the Optical Cable, use the Cable Holder at the rear panel of the YSP-1 to fix the cable (see
page 15).
Cables used for connections
■ Digital and analog connections ■ Video (OSD) connections
Connecting a TV
Optical Cable (supplied)
Audio Pin Cable (supplied)
OSD Video Cable (supplied)
For digital connections
For video (OSD) connections
(White)
(Red)
(White)
(Red)
SYSTEM
CONNECTOR
VIDEO
OUT
SUBWOOFER
OUTRS-232C COAXIAL
DVD AUX TV TV VCR
OPTICAL R L R L
DIGITAL INPUT
AUDIO INPUT
YSP-1 (Bottom panel)
TV
Optical digital
output
Analog audio
output
R L
SYSTEM
CONNECTOR
VIDEO
OUT
SUBWOOFER
OUTRS-232C COAXIAL
DVD AUX TV TV VCR
OPTICAL R L R L
DIGITAL INPUT
AUDIO INPUT
YSP-1 (Bottom panel)
TV
Video
input
13
CONNECTIONS
PREPARATION
To connect a DVD player/recorder, connect the coaxial digital output jack on your DVD player to the coaxial digital
input jack (DVD COAXIAL) on this unit.
If there is no coaxial digital output jack on your DVD player/recorder, use them with optical digital connection.
Cables used for connections
Connecting a DVD player/recorder
Digital Audio Pin Cable (supplied)
SYSTEM
CONNECTOR
VIDEO
OUT
SUBWOOFER
OUT
RS-232C COAXIAL
DVD AUX TV TV VCR
OPTICAL R L R L
DIGITAL INPUT
AUDIO INPUT
YSP-1 (Bottom panel)
Video signal
to a TV
DVD player/recorder
Coaxial digital
output
14
CONNECTIONS
To connect a VCR, connect the analog audio output jack on your VCR to the analog audio input jack (VCR R/L) on this
unit.
Connect red plugs to the right jacks and white plugs to the left jacks.
Cables used for connections
Connecting a VCR
Audio Pin Cable
(White)
(Red)
(White)
(Red)
SYSTEM
CONNECTOR
VIDEO
OUT
SUBWOOFER
OUT
RS-232C COAXIAL
DVD AUX TV TV VCR
OPTICAL R L R L
DIGITAL INPUT
AUDIO INPUT
YSP-1 (Bottom panel)
Video signal
to a TV
VCR
Analog audio
output
R L
(White)
(Red)
(White)
(Red)
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/