Yamaha YRS-2000 Инструкция по применению

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

YRS-2000

SURROUND SOUND TV STAND

MEUBLE TV SURROUND

G

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

i En

1. To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2. Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at

least 5 cm (2 in) on the top, 5 cm (2 in) on the left and right,

and 5 cm (2 in) on the back of this unit.

3. Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4. Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e., a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5. Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

— Other components, as they may cause damage and/or

discoloration on the surface of this unit.

— Burning objects (i.e., candles), as they may cause fire,

damage to this unit, and/or personal injury.

— Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6. Do not cover this unit with a newspaper, tablecloth, curtain,

etc., in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7. Do not plug in this unit to a wall outlet until all connections

are complete.

8. Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9. Do not use force on switches, knobs and/or cords.

10. When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11. Do not clean this unit with chemical solvents; this might

damage the finish.

12. Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and

may cause fire, damage to this unit, and/or personal injury.

Yamaha will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

13. To prevent damage by lightning, keep the power cord

disconnected from a wall outlet or the unit during a lightning

storm.

14. Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15. When not planning to use this unit for long periods of time

(i.e., vacation), disconnect the AC power plug from the wall

outlet.

16. Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17. Be sure to read the “Troubleshooting” section in the owner’s

manual on common operating errors before concluding that

this unit is faulty.

18. Before moving this unit, press STANDBY/ON to set the unit

in standby mode, then disconnect the AC power plug from

the AC wall outlet.

19. The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like.

Caution: Read this before operating this unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as long

as it is connected to the AC wall outlet, even if this unit itself is

turned off by STANDBY/ON. This state is called the standby

mode. In this state, this unit is designed to consume a very small

quantity of power.

FOR U.K. CUSTOMERS

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the instructions

described below. Note that the plug severed from the mains lead

must be destroyed, as a plug with bared flexible cord is

hazardous if engaged in a live socket outlet.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Make sure that neither core is connected to the earth terminal of

the three pin plug.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type.

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

Notes

• This unit’s speakers use magnets. Do not place items

that are sensitive to magnetism, such as CRT-type

TVs, clocks, credit cards, floppy disks, etc., on top

of the rack.

• When the unit is positioned close to a CRT-type TV,

picture or sound distortion may occur. In this case,

move the TV away from the unit.

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

SETUP

English

1 En

Overview................................................................. 2

Features .................................................................. 3

Using this manual .................................................. 5

Supplied accessories .............................................. 6

Controls and functions.......................................... 7

Front panel ................................................................ 7

Front panel display ................................................... 8

Rear panel ................................................................. 9

Remote control........................................................ 10

Installation............................................................ 13

Before installing this unit........................................ 13

Installing this unit ................................................... 13

Connections.......................................................... 15

Before connecting components............................... 16

Connecting a TV..................................................... 17

Connecting a DVD player/recorder........................ 18

Connecting a digital satellite tuner or

a cable TV tuner ................................................. 19

Connecting a digital airwave tuner......................... 20

Connecting a VCR.................................................. 21

Connecting other external components .................. 22

Connecting the AC power supply cable ................. 23

Getting started ..................................................... 24

Installing batteries in the remote control ................ 24

Operation range of the remote control.................... 24

Turning on this unit or

setting it to the standby mode............................. 25

Using SET MENU................................................ 26

Displaying the OSD (on-screen display) ................ 26

The flow chart of SET MENU................................ 27

Changing OSD language..................................... 28

AUTO SETUP (IntelliBeam).............................. 29

The flow chart of AUTO SETUP ........................... 29

Installing the IntelliBeam microphone ................... 30

Using AUTO SETUP (IntelliBeam)....................... 31

Using the system memory ................................... 36

Convenient usage of the system memory ............... 36

Saving settings........................................................ 36

Loading settings...................................................... 37

Playback ............................................................... 39

Selecting the input source....................................... 39

Playing back sources............................................... 40

Adjusting the volume.............................................. 41

Enjoying surround sound ................................... 42

5 Beam.................................................................... 42

Stereo plus 3 Beam................................................. 43

3 Beam.................................................................... 43

My Surround........................................................... 43

Enjoying 2-channel sources

in surround sound ............................................... 45

Enjoying TV in surround sound ............................. 46

Adjusting surround mode parameters..................... 47

Enjoying stereo sound ......................................... 48

Using the volume mode

(Night listening enhancer/TV volume equal

mode) ................................................................. 49

Using the sleep timer............................................ 50

Using the HDMI control feature......................... 52

MANUAL SETUP................................................ 53

Using MANUAL SETUP ....................................... 54

BEAM MENU ........................................................ 55

SOUND MENU...................................................... 59

INPUT MENU........................................................ 60

DISPLAY MENU................................................... 64

Adjusting the audio balance................................ 65

Using the test tone .................................................. 65

Using the audio output being played back.............. 66

Selecting the input mode...................................... 68

Adjusting the system parameters ....................... 69

Using the system parameters .................................. 69

Remote control features....................................... 71

Setting remote control codes .................................. 71

Controlling other components ................................ 72

Using the TV macro ............................................... 75

Troubleshooting.................................................... 77

Glossary................................................................. 80

Index...................................................................... 81

Specifications ........................................................ 82

Contents

INTRODUCTION

PREPARATION

SETUP

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

List of remote control codes ...............................i

Overview

2 En

It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of

wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of

surround sound experience as your local movie theater.

Yamaha YRS-2000 Surround Sound TV Stand challenges this preconception that complicated speaker setup and

troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.

YRS-2000 does away with the need for complicated wiring and installation worries, leaving you with a unit that is not

only easy to set up, but is also capable of reproducing the kind of powerful surround sound you have been waiting for

from its built-in a subwoofer, 2 woofers, and 16 full-range small speakers.

You can fine-tune the parameters of this unit to adjust the delay time for separate sound beams, resulting in highly

directional sound that comes in on the listening position from all directions.

The YRS-2000 projects sound beams containing surround sound information for the front right (R), front left (L),

surround right (SR), and surround left (SL) speaker positions, which are reflected off the walls of your listening room

before reaching the actual listening position. With the addition of center (C) and subwoofer sound beams, this Surround

Sound TV Stand creates true-to-life 5.1-channel surround sound that makes you feel as if there are actual speakers

around the room.

Sit back and enjoy the real sound experience of this simple, yet stylish the Surround Sound TV Stand.

Overview

SL

SR

R

L

C

Listening position

Imaginary surround

left speaker

Imaginary

surround right

speaker

Imaginary front

left speaker

Imaginary front right

speaker

Imaginary center

speaker

Features

3 En

INTRODUCTION

English

Digital Sound Projector™

The Digital Sound Projector technology allows one slim

unit to control and steer multiple channels of sound to

generate multi-channel surround sound, thus eliminates

the need for satellite loudspeakers and cabling normally

associated with conventional surround sound systems.

The YRS-2000 employs this technology.

This unit also employs the beam modes that let you enjoy

the surround sound (5 Beam, Stereo plus 3 Beam and

3 Beam), and stereo playback (Refer to page 42–48).

My Surround

In addition to the above mentioned beam modes, this unit

is equipped with My Surround beam mode that allows you

to enjoy surround system even in a small listening area.

My Surround is a function integrated and optimized with

DiMAGIC’s Euphony technology and Yamaha’s Beam

reproduction system (Refer to page 43).

HDMI™ (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced, or high-definition

video (including 1080p video signal transmission) as well as

multi-channel digital audio based on HDCP

◆ Simple and easy connections with HDMI supported external

components

◆ Functional link with an HDMI control-compatible TV

(Refer to Quick Setup Guide for HDMI connection, and

refer to page 52 for HDMI features.)

Versatile Remote Control

The supplied remote control comes with preset remote

control codes used to control the DVD, Blu-ray, HD DVD

player (recorder), VCR, cable TV tuner, and digital

satellite tuner connected to this unit. In addition, the

remote control is equipped with the macro capability that

enables a series of operations with the press of a single

button (Refer to page 71–76).

AUTO SETUP (IntelliBeam)

This unit employs the automatic sound beam and acoustic

optimization technology with the aid of the supplied

IntelliBeam microphone. You can avoid troublesome

listening-based speaker setup and achieve highly accurate

sound beam adjustments that best match your listening

environment.

Compatibility with the Newest Technologies

This unit employs decoders compatible with Dolby

Digital, DTS, Dolby Pro Logic, Dolby Pro Logic II, and

DTS Neo:6.

◆ Dolby Digital

This is the standard audio signal format used on various

digital media such as DVD, Blu-ray, and HD DVD. This

surround technology delivers high-quality digital audio for up

to 5.1 discrete channels to produce a directional and more

realistic effect.

◆ DTS

This is the standard audio signal format used on various

digital media such as DVD, Blu-ray, and HD DVD. This

surround technology delivers high-quality digital audio for up

to 5.1 discrete channels to produce a directional and more

realistic effect.

◆ Dolby Pro Logic

A surround system that takes a 4-channel signal and records it

as a 2-channel signal, then by way of some arithmetic

processing converts back to an independent 4-channel signal

for playback.

◆ Dolby Pro Logic II

Dolby Pro Logic II is an improved technique used to decode

vast numbers of existing Dolby Surround software.

This new technology enables a discrete 5-channel playback

with 2 front left and right channels, 1 center channel, and 2

surround left and right channels (instead of only 1 surround

channel for conventional Pro Logic technology).

◆ DTS Neo:6

This technology decodes the conventional 2-channel sources

for 6-channel playback, enabling playback with the full-range

channels with higher separation. Music mode and Cinema

mode are available to play back music and movie sources

respectively.

Features

4 En

The “ ” logo and “IntelliBeam” are trademarks of

Yamaha Corporation.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS” and “Neo:6” are registered trademarks of DTS, Inc.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks or registered trademarks of HDMI

Licensing LLC.

Manufactured under license from 1 Ltd. Worldwide patents

applied for.

The “ ” logo and “Digital Sound Projector

™

” are trademarks

of 1 Ltd.

™

is a trademark of DiMAGIC Co., Ltd.

Using this manual

5 En

INTRODUCTION

English

• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the

supplied owner’s manual for each component.

• About assembling this unit, refer to the supplied Quick Setup Guide.

• Operations in this manual use keys on the supplied remote control of this unit unless otherwise specified.

• y indicates a tip for your operation.

• This manual is printed prior to production. Designs and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and the product, the product has priority.

1 After assembling, install this unit in your listening room.

See the separate “Quick Setup Guide” and “Installation” on page 13.

2 Connect this unit to your TV and other external components.

See the separate “Quick Setup Guide” and “Connections” on page 15.

3 Prepare the remote control and turn on the power of this unit.

See “Getting started” on page 24.

4 Run AUTO SETUP.

See “AUTO SETUP (IntelliBeam)” on page 29.

5 Play back a source.

See “Playback” on page 39.

6 Change the beam modes.

See “Enjoying surround sound” on page 42.

7 Run MANUAL SETUP to fine-tune settings and/or set remote control codes.

See “MANUAL SETUP” on page 53 and “Remote control features” on page 71.

Using this manual

Notes

If you want to make additional settings

and adjustments

Supplied accessories

6 En

Check that you have received all of the following parts.

Supplied accessories

STEREO MY SUR.

SLEEP

INPUTMODE

CH LEVEL MENU

RETURNTEST

TV VOL

VOLUME

MUTE

TV INPUT TV MUTE

ENTER

SUR. DECODE

CODE SET

5BEAM ST+3BEAM 3BEAM

VOL MODE

AUTO

SETUP

MACRO

TV

INPUT2INPUT1

YSP

TV/AV

CH

4

6

321

VCR DVD

TV

STB AUX

TV

POWERPOWERSTANDBY/ON

+10

0

789

5

AV

Remote control (×1)

Battery (×2)

(AA, R6, UM-3)

OSD* video pin cable (×1)

IntelliBeam microphone

(×1)

Audio pin cable (×1)

Optical cable (×1)

Cardboard microphone

stand (×1)

(White/Red)

(Yellow)

Quick Setup Guide

* The number of provided languages

varies depending on the model.

*OSD: On-Screen Display

Controls and functions

7 En

INTRODUCTION

English

1 INTELLIBEAM MIC jack (underside)

Connect the supplied IntelliBeam microphone for AUTO

SETUP (see page 30).

2 Remote control sensor

Receives infrared signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit.

4 INPUT

Press repeatedly to switch between input sources (see

page 39).

5 VOLUME +/–

Controls the volume level of all audio channels (see

page 41).

6 STANDBY/ON

Turns on the power of this unit or sets it to the standby

mode (see page 25).

• When you turn on this unit, you will hear a click sound

followed by the 4 to 5-second interval before sound

reproducing.

• In the standby mode, this unit consumes a small amount of

power in order to receive infrared signals from the remote

control or to search for HDMI signals.

Controls and functions

Front panel

HOME THEATER RACK SYSTEM

INPUT

VOLUME STANDBY

/

ON

–+

YRS

–

2000

4651

2 3

Notes

Controls and functions

8 En

1 HDMI indicator

Lights up when the signal of the selected input source is

input at the HDMI IN jack(s).

2 EQUAL indicator

Lights up when the TV volume equal mode is selected

(see page 49).

3 NIGHT indicator

Lights up when one of the night listening enhancers is

selected (see page 49).

4 SLEEP indicator

Lights up when the sleep timer is set (see page 50).

5 Decoder indicators

Light up when the corresponding decoder operates

(see page 44).

6 PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code

Modulation) digital audio signals.

7 MULTI indicator

Lights up when this unit detects a multi channel digital

audio signal (see page 40).

8 Volume level indicator

Displays the current volume level.

9 Multi-information display

Shows information with alphanumeric characters when

you adjust the parameters of this unit.

y

You can adjust the brightness and display setting of the front

panel display using the F.DISPLAY SET parameter in MANUAL

SETUP (see page 64).

Front panel display

1 2 3 4

6 7

8

9

5

Controls and functions

9 En

INTRODUCTION

English

1 HDMI OUT jack

Connect to the HDMI input jack on your HDMI

component such as a TV or a projector connected to this

unit (see the separate “Quick Setup Guide”).

2 DVD HDMI IN jack

Connect your DVD player via an HDMI connection (see

the separate “Quick Setup Guide”).

3 AUX HDMI IN jack

Connect your digital satellite tuner, cable TV tuner, digital

airwave tuner, or game console via an HDMI connection

(see the separate “Quick Setup Guide”).

4 VCR AUDIO INPUT jacks

Connect your VCR via an analog connection (see

page 21).

5 TV/STB AUDIO INPUT jacks

Connect your TV, digital satellite tuner, or cable TV tuner

via an analog connection (see pages 17 and 19).

6 VIDEO OUT jack

Connect to the video input jack of your TV to display the

OSD of this unit (see page 17).

7 TV/STB OPTICAL DIGITAL INPUT jack

Connect your TV, digital satellite tuner, or cable TV tuner

via an optical digital connection (see pages 17 and 19).

8 AUX OPTICAL DIGITAL INPUT jack

Connect an external component via an optical digital

connection (see page 22).

9 DVD COAXIAL DIGITAL INPUT jack

Connect your DVD player via a coaxial digital connection

(see page 18).

0 AC power supply cable

Connect to the AC wall outlet (see page 23).

Rear panel

DVDOUT AUXIN

OUT DIGITAL INPUT

AUDIO INPUT

VCR TV/STB TV/STB AUX DVDVIDEO

OPTICAL

COAXIAL

L

R

HDMI

0

DVDOUT AUXIN

OUT DIGITAL INPUT

AUDIO INPUT

VCR TV/STB TV/STB AUX DVDVIDEO

OPTICAL

COAXIAL

L

R

HDMI

12

7 8 9

4

6

5

3

Controls and functions

10 En

This section describes the functions of the remote control

used to control this unit. Some buttons marked with an

asterisk (*) share the common functions between the YSP

and TV/AV operation modes (M).

y

You can also control other components using the remote control

once you set the appropriate remote control codes. See

“Controlling other components” on page 72 for details.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 STANDBY/ON

Turns on the power of this unit or sets it to the standby

mode (see page 25).

3 Transmission indicator

Lights up when infrared control signals are being output.

4 Input selector buttons

Use to select an input source (STB, VCR, DVD, AUX, or

TV).

5 VOL MODE

Turns on or off the volume modes (see page 49).

6 AUTO SETUP

Enters the AUTO SETUP menu (see page 31).

7 CH LEVEL

Adjusts the volume level of each channel (see page 66).

8 Cursor buttons / / / , ENTER

Select and adjust SET MENU items.

9 TEST

Outputs a test tone when adjusting the output level of each

channel (see page 65).

0 VOLUME +/–

Increases or decreases the volume level of this unit (see

page 41).

A MUTE

Mutes the sound. Press again to restore the audio output to

the previous volume level (see page 41).

B TV INPUT

Toggles between the input sources on the TV (see

page 72).

C DVD player/VCR control buttons

Control your DVD player or VCR (see pages 73 and 74).

D TV POWER

Turns on the power of your TV or sets it to the standby

mode (see page 72).

E AV POWER

Turns on the power of the selected component or sets it to

the standby mode (see pages 73 and 74).

F INPUT1/INPUT2

Switches the input source on your TV (see page 72).

G MACRO

Use to set the TV macro (see page 75).

Remote control

4

6

321

+10

0

789

5

STEREO

SLEEP

INPUTMODE

CH LEVEL MENU

RETURNTEST

TV VOL

VOLUME

MUTE

TV INPUT TV MUTE

CODE SET

5BEAM ST+3BEAM 3BEAM

VOL MODE

AUTO

SETUP

MACRO

TV

INPUT2INPUT1

YSP

TV/AV

CH

STB

TV

VCR DVD AUX

TVAV

POWERPOWERSTANDBY/ON

ENTER

SUR. DECODE

MY SUR.

1

D

E

F

H

G

I

J

K

L

M

N

O

P

Q

2

3

4

5

6

7

9

8

0

A

B

C

*

Controls and functions

11 En

INTRODUCTION

English

H SLEEP

Sets the sleep timer (see page 50).

I INPUTMODE

Toggles between input modes (AUTO, DTS, and

ANALOG) (see page 68).

J Beam mode buttons

Change the beam mode settings (see pages 42 and 48).

K SUR. DECODE

Selects the surround mode for playback (see page 45).

L MENU

Displays the setup menu on your TV monitor (see

pages 31 and 54) or turns off the setup menu.

M Operation mode selector

Selects the operation mode of this unit. Select YSP when

operating this unit and select TV/AV when operating your

TV or other AV components.

N RETURN

Returns to the previous SET MENU screen.

O TV VOL +/–

Adjusts the volume level of your TV (see page 72).

P CH +/–

Changes the channels of your TV, digital satellite tuner,

cable TV tuner, or VCR (see pages 72 to 75).

Q TV MUTE, CODE SET

Mutes the audio output of your TV (see page 72).

Sets up remote control codes (see page 71).

Controls and functions

12 En

This section describes the functions of the remote control

used to control other components when the TV/AV mode

is selected with the operation mode selector (4).

1 Numeric buttons

Enter numbers.

2 Cursor buttons / / / , ENTER

Use to select DVD menu items.

3 MENU

Displays the DVD menu or turns off the DVD menu.

4 Operation mode selector

Selects the operation mode of this unit. Select YSP when

operating this unit and select TV/AV when operating your

TV or other AV components.

5 RETURN

Use to return to the previous DVD menu.

4

6

321

+10

0

789

5

STEREO

SLEEP

INPUTMODE

CH LEVEL MENU

RETURNTEST

TV VOL

VOLUME

MUTE

TV INPUT TV MUTE

CODE SET

5BEAM ST+3BEAM 3BEAM

VOL MODE

AUTO

SETUP

MACRO

TV

INPUT2INPUT1

YSP

TV/AV

CH

STB

TV

VCR DVD AUX

TVAV

POWERPOWERSTANDBY/ON

ENTER

SUR. DECODE

MY SUR.

1

2

4

3

5

Installation

13 En

PREPARATION

English

After assembling the main unit and rack, place the unit in an appropriate location. For information on assembling the

main unit and rack, please refer to the separate “Quick Setup Guide”.

This unit creates surround sound by reflecting projected

sound beams off the walls of your listening room. The

surround sound effects produced by this unit may not be

sufficient when this unit is installed in the following

locations.

• Rooms with walls inadequate for reflecting sound

beams

• Rooms with acoustically absorbent walls

• Rooms with measurements outside the following

range: W (3 to 7 m (10 to 23 ft)) x H (2 to 3.5 m (7 to

11.5 ft)) x D (3 to 7 m (10 to 23 ft))

• Rooms with less than 1.8 m (6 ft) from the listening

position to this unit

• Rooms where objects such as furniture are likely to

obstruct the path of sound beams

• Rooms where the listening position is close to the walls

• Rooms where the listening position is not in front of

this unit

y

• You can enjoy surround sound by selecting My Surround (see

page 43) as the beam mode even if your listening room may not

fulfill the above conditions (except when the listening position

is not directly facing toward the front of this unit).

• You can also enjoy surround sound by selecting stereo playback

(see page 48) as the beam mode even if your listening room

may not fulfill the above conditions.

Be sure to allow sufficient ventilation space behind the

unit so that heat will not build up.

The unit weighs 61 kg (134 lbs, 8 oz). Install the unit securely so

that it will not fall due to impact or shaking of the floor, such as

during an earthquake, or if a child bumps into the unit.

■ Caution: Handling the tempered glass

The top glass panel is constructed of glass that has been

tempered for strength and safety.

In addition, a safety film has been applied to the tempered

glass to offer additional protection against injuries that

may be caused by shattering glass.

However, if you handle the glass inappropriately, the glass

might break and glass fragments might fly, causing injuries.

Be sure to follow the precautions listed below:

• Do not allow any strong impacts to the glass (for

example, do not allow thrown objects to strike the

glass).

• Do not allow sharp objects to contact the glass.

• If the tempered glass has been scratched, it might break

unexpectedly. If you see scratches, replace the glass

immediately.

Install this unit where there are no obstacles such as

furniture obstructing the path of sound beams. Otherwise,

the desired surround sound effects may not be achieved.

You may install this unit in parallel with the wall or in the

corner.

Parallel installation

Install this unit in the exact center of the wall when it is

measured from the left and right corners.

Corner installation

Install this unit in the corner at a 40º to 50º angle from the

adjacent walls.

Installation

Before installing this unit

Note

Installing this unit

An object, such as furniture

40° to 50°

An object, such as furniture

14 En

Installation

■ Installation examples

Example 1

Install this unit as close to the exact center of the wall as possible.

Example 2

Install this unit so that the sound beams can be reflected off the walls.

Example 3

Install this unit as close to the exact front of your normal listening position as possible.

Connections

15 En

PREPARATION

English

This unit is equipped with the following types of audio/video input/output jacks/terminal:

For audio input

• 2 optical digital input jacks

• 1 coaxial digital input jack

• 2 sets of analog input jacks

For audio/video input

• 2 HDMI input jacks

For audio/video output

• 1 HDMI output jack

For video output

• 1 analog output jack

Use these jacks/terminal to connect external components such as your TV, DVD player, VCR, digital satellite tuner,

cable TV tuner, digital air wave tuner, and game console. For details on how to connect various types of external

components to this unit, see pages 17 to 23.

• Do not connect this unit or other components to the mains power until all connections between components are

complete.

• Unplug the AC power supply cable before changing connections, moving or cleaning this unit.

When you connect the unit to the components:

Please also refer to the owner’s manual supplied with the

components.

Please refer to the separate “Quick Setup Guide” for information

on how to connect the unit and components using the HDMI

connectors.

Connections

CAUTION

HOME THEATER RACK SYSTEM

INPUT

VOLUME STANDBY

/

ON

–+

YRS

–

2000

TV

This unit

Audio connection

Video connection

VCR or game

console

BD/DVD player

Digital satellite tuner

or cable TV tuner

The diagram above shows the signal flow in a

system that does not feature an HDMI

connection. Please refer to the section

starting on page 17 for more information on

this connection.

Note

16 En

Connections

■ Cables used for connections

HDMI cable

Audio pin cable (supplied)

Optical cable (supplied)

Digital audio pin cable

OSD video pin cable (supplied)

■ Notes on connecting the optical cable

• Pull out the cap before connecting the optical cable.

When you are not using the optical cable, be sure to put

the cap back in place.

• When inserting the cable into the optical digital jack,

make sure the direction is correct.

■ Information on HDMI™

Audio signals

•

When CPPM copy-protected DVD audio is played back, video and

audio signals may not be output depending on the type of DVD player.

• This unit is not compatible with HDCP-incompatible HDMI or

DVI components.

y

• We recommend that you use an HDMI cable shorter than 5 m

(16 ft) with the HDMI logo printed on it.

• Use a conversion cable (HDMI jack

↔ DVI-D jack) to connect

this unit to other DVI components.

■ Priority order for audio input signals

When multiple types of audio signals are simultaneously

being input from a single source component, this unit

plays back the audio signals in the following priority

order: HDMI → Digital → Analog

As default settings, the following input jacks are assigned

to the corresponding input sources:

This unit is compatible with 2-channel PCM signals, but not with

multi-channel PCM signals.

Before connecting components

Audio/Video

Audio

Video

A

(White)

(Red)

(White)

(Red)

(Orange)(Orange)

(Yellow)(Yellow)

Cap

Input source Audio signal type

DVD video Dolby Digital, DTS, PCM

DVD audio

2-channel stereo

(up to 96 kHz/24 bit)

Blu-ray Disc

HD DVD

Dolby Digital, DTS, PCM

Notes

Input

jack

Input

source

HDMI Digital Analog

TV/STB ✔✔

DVD ✔✔

AUX ✔✔

VCR ✔

Note

17 En

Connections

PREPARATION

English

For audio connection, connect the analog audio output jacks on your TV to the TV/STB AUDIO INPUT jacks on this

unit. If your TV has an optical digital output jack, connect the optical digital output jack on your TV to the TV/STB

OPTICAL DIGITAL INPUT jack on this unit.

For video connection, connect the video input jack on your TV to the VIDEO OUT jack on this unit to display the OSD

for easy viewing when you adjust the system parameters in SET MENU.

If you make analog and optical digital audio connections at the same time as shown in the illustration below, the digital audio signals

input at the TV/STB OPTICAL DIGITAL INPUT jack take priority over the analog audio signals input at the TV/STB AUDIO INPUT

jacks.

OSD video pin cable Audio pin cable

Optical cable

Connecting a TV

Note

VCR TV/STB VIDEO TV/STB AUX

OPTICAL

COAXIAL

DIGITAL INPUT

OUT

AUDIO INPUT

DVD

R

L

Rear panel of this unit

TV

Optical

digital

output

RL

Video

input

Analog

audio

output

Video Audio

18 En

Connections

Connect the coaxial digital output jack on your DVD player/recorder to the DVD COAXIAL DIGITAL INPUT jack on

this unit. When you connect this unit to your DVD/VCR combo player/recorder, connect the analog audio output jacks on

your DVD/VCR combo player/recorder to the VCR AUDIO INPUT jacks on this unit in addition to the coaxial digital

audio connection.

• Check that your DVD player/recorder is properly set to output Dolby Digital and DTS digital audio signals. If not, adjust the system

settings of your DVD player/recorder. For details, refer to the operation manual supplied with your DVD player/recorder.

• If your DVD player/recorder does not have a coaxial digital output jack, make an optical digital audio connection instead (see

page 22).

Audio pin cable

Digital audio pin cable

Connecting a DVD player/recorder

Notes

R

L

VCR TV/STB VIDEO TV/STB AUX

OPTICAL

COAXIAL

DIGITAL INPUT

OUT

AUDIO INPUT

DVD

Coaxial

digital

output

Analog

audio

output

LR

DVD player/recorder

Video signal to the TV

Rear panel of this unit

*

For the DVD/VCR

combo player/recorder

connection

Audio

Страница загружается...

Yamaha YRS-2000 Инструкция по применению

Похожие модели бренда

Модели других брендов