Sony MZ-B100 Руководство пользователя

3-235-455-12(1)

Portable

MiniDisc Recorder

Operating Instructions _______________________

_

Manual de instrucciones _____________________

_

_______________

_

GB

ES

RU

MZ-B100

Portable MiniDisc Recorder MZ-B100

2-GB

model name1[MZ-B100] model name2[MZ------]

[3-235-455-12(1)]

masterpage:Left

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\020REG.fm]

Owner’s Record

The serial number is located at the rear of

the disc compartment lid and the model

number is located at the top and bottom.

Record the serial number in the space

provided below. Refer to them whenever

you call upon your Sony dealer regarding

this product.

Model No. MZ-B100

Serial No.

This equipment has been tested and found

to comply with the limits for a Class B

digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment generates,

uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur

in a particular installation. If this

equipment does cause harmful

interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user

is encouraged to try to correct the

interference by one or more of the

following measures:

— Reorient or relocate the receiving

antenna.

— Increase the separation between the

equipment and receiver.

— Connect the equipment into an outlet

on a circuit different from that to

which the receiver is connected.

— Consult the dealer or an experienced

radio/TV technician for help.

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and

(2) this device must accept any

interference received, including

interference that may cause undesired

operation.

You are cautioned that any changes or

modifications not expressly approved in

this manual could void your authority to

operate this equipment.

Caution

The use of optical instruments with this

product will increase eye hazard.

CAUTION — INVISIBLE LASER

RADIATION WHEN OPEN

AVOID EXPOSURE TO BEAM

Information

Certain countries may regulate disposal of

the battery used to power this product.

Please consult with your local authority.

IN NO EVENT SHALL SELLER BE

LIABLE FOR ANY DIRECT,

INCIDENTAL OR

CONSEQUENTIAL DAMAGES OF

ANY NATURE, OR LOSSES OR

EXPENSES RESULTING FROM

ANY DEFECTIVE PRODUCT OR

THE USE OF ANY PRODUCT.

model name1[MZ-B100] model name2[MZ------]

[3-235-455-12(1)]

masterpage:Right

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\020REG.fm]

3-GB

Disposal of Old Electrical &

Electronic Equipment

(Applicable in the European

Union and other European

countries with separate

collection systems)

This symbol on the product

or on its packaging indicates

that this product shall not be

treated as household waste.

Instead it shall be handed

over to the applicable

collection point for the

recycling of electrical and electronic

equipment. By ensuring this product is

disposed of correctly, you will help

prevent potential negative consequences

for the environment and human health,

which could otherwise be caused by

inappropriate waste handling of this

product. The recycling of materials will

help to conserve natural resources. For

more detailed information about recycling

of this product, please contact your local

city office, your household waste disposal

service or the shop where you purchased

the product.

Applicable accessories: Remote control,

Headphones

GB

4-GB

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Left

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\020REGTOC.fm]

Table of contents

Looking at the controls ....................................6

Preparing a power source ................................ 9

Recording an MD right away! ......................... 11

Playing an MD right away! .............................. 14

Various ways of recording .............................. 16

Recording for long times ......................................................................16

VOR (Voice Operated Recording) .......................................................17

Recording from a microphone ..............................................................18

Recording from externally connected equipment .................................19

Recording with digital (optical) input (optical cable required) ......20

Recording with analog (line) input (line cable required) ...............21

Recording tracks using the Group Function (Group mode recording) .22

To activate the group mode (Group mode recording) ....................23

Recording a track into a new group ................................................23

Recording a track into an existing group ........................................23

To start/stop recording in sync with the source player

(Synchro-recording) ........................................................................24

Setting the clock to stamp the recorded time ........................................25

Checking the remaining time or the recording position .......................26

Various ways of playback .............................. 27

Changing the sound setting ...................................................................27

Finding a point quickly (Easy Search) ..................................................28

Changing the playback speed (Speed Control) .....................................28

Playing tracks repeatedly ......................................................................29

Checking the remaining time or the playing position ...........................29

Using the Group Function (Group mode) .............................................30

Listening to tracks using the group mode (group mode playback) 30

Selecting and playing groups (Group skip mode) ..........................31

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Right

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\020REGTOC.fm]

5-GB

Editing recorded tracks .................................. 32

Adding a track mark ............................................................................. 32

Track marking to divide a recording .............................................. 32

Track marking important points .................................................... 32

Erasing a track mark ............................................................................ 33

Labeling recordings .............................................................................. 34

Registering tracks or groups as a new group (Group setting) .............. 36

To release a group setting .................................................................... 37

Moving recorded tracks ....................................................................... 38

Moving a track to a different group ..................................................... 38

Changing the order of a group on a disc (Group move) ...................... 39

Erasing tracks ....................................................................................... 39

To erase a track .............................................................................. 39

To erase the whole disc .................................................................. 40

To erase a group ............................................................................. 40

Other operations ............................................. 41

Adjusting the contrast of the display window (Contrast adjustment) .. 41

Locking the controls (HOLD) .............................................................. 41

Power sources ................................................ 42

When to replace the batteries ............................................................... 42

Battery life ..................................................................................... 42

Using house current ............................................................................. 43

Additional information .................................... 44

Precautions ........................................................................................... 44

Troubleshooting ................................................................................... 46

System limitations ................................................................................ 49

Messages .............................................................................................. 50

Specifications ....................................................................................... 52

Explanations ......................................................................................... 53

6-GB

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Left

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\030GET.fm]

Looking at the controls

See pages in ( ) for more details.

Front of the recorder

A SPEED CONTROL dial (28)

B .REVIEW/AMS/>CUE/AMS

(search /AMS) buttons (12) (15) (23)

(25) (31) (33) (34) (41)

C VOR indicator (17)

D DISPLAY button (26) (29) (35)

E PLAY MODE button (29) (35)

F EDIT/ENTER button (31) (34) (41)

G EASY SEARCH +/– buttons (28)

(35)

H Display window (24) (27) (33)

I xSTOP button (12) (14) (25) (35)

J NPLAY (play) button (12) (14) (25)

(34)

The NPLAY button has a tactile dot.

K XPAUSE button (13) (15) (33) (34)

L zREC button (12) (16)

M REC indicator (12) (26)

N TRACK MARK button (32) (33)

O REC MODE switch (12) (16)

P GROUP button (23) (30) (37)

Q Speaker (14)

R DC IN 3V jack (43)

S Microphones (12) (17)

T i (headphones) jack (12) (14)

U OPEN switch (11) (14)

V HOLD switch (9) (41)

W VOL control (14)

The VOL control has a tactile dot.

X VOR button (17)

Y SYNCHRO REC ON/OFF switch

(24)

Z ERASE button (39)

1

2

9q;qaqsqdqfqg qh w; wa ws wd wf wgwh

3456 78 qj qk ql

How to attach the hand strap.

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Right

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\030GET.fm]

7-GB

Back of the recorder

A Battery compartment (9)

B CLOCK SET button (25)

C SOUND button (27)

D LINE IN (OPTICAL) jack (20) (21)

E MIC (PLUG IN POWER) jack (18)

The MIC (PLUG IN POWER) jack

has a tactile dot.

F MIC SENS (H/L) switch (11) (17)

The display window

A Character information display (16)

(27) (33)

Displays the disc and track names,

date, error messages, track numbers,

recording level, etc.

B Group indication (23) (30) (35)

C Play mode indication (29)

D Disc indication (16) (27) (33)

Shows that the disc is rotating for

recording, playing or editing an MD.

E VOR indication (17)

F Battery level indication (42)

G SYNC (synchro-recording) indication

(24)

H Playback level meter (30) (33)

I V-UP indication (27)

J STEREO (stereo), LP2 (LP2 stereo),

LP4 (LP4 stereo), MONO (monaural)

indication (12) (16)

K Pause indication

L SOUND indication (27)

M REC indication (12)

2

1

36

4

5

124567

qdqsqaq;98

3

8-GB

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Left

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\030GET.fm]

The remote control

A Stereo mini plug

B SOUND button (27)

C TRACK MARK button (32) (33)

D HOLD switch (9) (41)

Slide to lock the controls of the

remote control.

E X (pause) button (15)

F Headphones

G x (stop) button (14)

H >N buttons (15)

The >N button has a tactile dot.

I .REVIEW/AMS (15)

J VOL control (14)

The VOL control has a tactile dot.

A

B

C

D

E

G

F

H

I

J

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Right

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\030GET.fm]

9-GB

Preparing a power source

This section explains how to prepare the recorder for battery-powered

operation. For information on connecting the recorder to an AC power

outlet, see page 43.

1

Insert dry batteries.

2

Unlock the control.

e

E

Back of the recorder

Press and slide the battery

compartment lid as shown in

the illustration.

Notes

• Do not use manganese dry battery. If you do, recording may not be possible.

• Insert the e and E poles of the battery correctly as shown on the recorder.

Close the lid.

Insert one LR6 (size AA)

alkaline dry battery

(supplied with the world

model only).

Slide HOLD to the direction of the arrow in the illustration.

HOLD

10-GB

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Left

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\030GET.fm]

Charging the built-in battery for the clock

When you use the recorder for the first time or after a long period of disuse, charge the

built-in battery for the clock. After setting the clock, leave the dry batteries installed for

about more than two hours so that the built-in battery is automatically charged. You can use

the recorder while charging. When the built-in battery is charged, the settings, such as

clock, will remain for about one month after dry batteries are taken out. For details on

setting a clock, see page 25.

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Right

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\030GET.fm]

11-GB

Recording an MD right away!

Use the built-in microphones to record in stereo. Make sure the

record-protect tab on the disc is closed (page 54). The use of new

alkaline dry battery is recommended. The recording may not be

possible if you use manganese dry battery.

1

Insert a recordable MD.

1 Slide OPEN to open the lid. 2 Insert a recordable MD with the label

side facing up, and press down on the

lid (at the center of the front edge as

shown above) to close it firmly.

2

Select the microphone sensitivity.

1 Slide MIC SENS to H or L.

MIC SENS

MIC SENS When

H (high) recording a soft or a

sound in the distance

(e.g. to record a

meeting).

L (low) recording a laud or a

sound at close range

(e.g. to record a speech

through a microphone).

12-GB

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Left

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\030GET.fm]

3

Select the recording mode.

4

Record an MD.

1 Press zREC.

“REC” appears, REC indicator lights

up, and then recording starts.

You can monitor the recording

conditions, such as the recording

position, through the display or the REC

indicator (page 26).

If the disc is blank, the recording

starts from the beginning. If the

disc is partially recorded, the

recording automatically starts

from the end of the existing

material.

To stop recording, press xSTOP.

After you press the xSTOP button to stop the

recorder, the recorder will automatically turn

off after about 10 seconds (when using an

alkaline dry battery) or 5 minutes (when using

the AC power adaptor).

To monitor the sound during recording.

Connect the supplied headphones with remote control to the i jack. You can adjust the volume by

turning the VOL control. This adjustment does not affect the recording level since the level is adjusted

automatically.

1 Press REC MODE repeatedly until “STEREO” lights

up in the display.

You can select normal stereo, LP2 stereo, LP4 stereo,

or monaural as the recording mode. For details, see

“Recording for long times” (page 16). The factory

setting is normal stereo.

The recording mode cannot be changed when

recording is in progress.

REC MODE

xSTOP

zREC

REC

indicator

built-in

microphones

x

Connect

firmly to i.

Connect firmly to i

To Operation

Record partway through the

previous recording

Press NPLAY, >CUE/AMS or .REVIEW/

AMS to find the beginning of the material to be

recorded, and then press XPAUSE.

Press zREC so that the recorder changes to

recording pause.

Press XPAUSE again to start recording.

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Right

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\030GET.fm]

13-GB

If the recording does not start

• Make sure the recorder is not locked (pages 9

and 41).

• Make sure the MD is not record-protected

(page 54).

• Premastered MDs cannot be recorded over.

Notes

• For long recordings, it is recommended that

you power the recorder from a house current

using an optional AC power adaptor AC-

E30HG (page 43).

• Do not connect an optional AC power adaptor

during a recording operation if you are

operating the recorder on battery power. If you

do, the material recorded up to that point will

not be saved to the disc

• The lid will not open during recording or until

“TOC Edit” disappears from the display after

the recording has completed.

• If the power supply is disrupted (i.e. the

batteries are removed or becomes exhausted

or the optional AC power adaptor is

disconnected) during a recording operation, or

while “TOC Edit” appears in the display, then

it will not be possible to open the lid until

power is restored.

• “Data Save” or “TOC Edit” flashes while data

of the recording (the track’s start and end

points, etc.) is being recorded. Do not move or

jog the recorder or disconnect the power

source while the indication is flashing in the

display. If you do, the material recorded up to

that point will not be saved to the disc.

• When you record through the microphones,

the various sounds made by the recorder may

also be recorded.

• The built-in microphones do not operate

whenever an optional microphone is

connected into the MIC (PLUG IN POWER)

jack on the recorder.

• The built-in microphones do not operate

whenever an optical cable or a line cable is

connected into the LINE IN (OPTICAL) jack

on the recorder.

Pause

1)

Press XPAUSE while recording.

Press XPAUSE again to resume recording.

Remove the MD xSTOP to stop recording and open the lid. (Be sure

that “TOC Edit” has disappeared from the display

before opening the lid.)

1)

The REC indicator flashes during recording pause. Track marks are not added while recording with

microphones, even when the recorder is paused.

To Operation

14-GB

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Left

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\030GET.fm]

Playing an MD right away!

You can play recordable MDs or premastered MDs. Sound output

from the built-in speaker is monaural, but stereo listening is possible

through the supplied headphones with a remote control.

1

Insert an MD.

1 Slide OPEN to open the lid. 2 Insert an MD with the label side facing

up, and press down on the lid (at the

center of the front edge as shown

above) to close it firmly.

2

Play an MD.

1 Press NPLAY.

2 Turn VOL to adjust the volume.

The volume will be shown in the

display.

To stop play, press xSTOP.

Playback starts from the point you last stopped

playing. To start playback from the beginning

of the disc, press NPLAY for 2 seconds or

more on the recorder, or press >N for 2

seconds or more on the remote control.

After you press the

xSTOP button to stop the

recorder, the recorder will automatically turn

off after about 10 seconds (when using an

alkaline dry battery), or 5 minutes (when using

the AC power adaptor).

On the remote control, use the >N button

to start playback, the xSTOP button to stop the

recorder, and the VOL control to adjust the

volume. If you are using the remote control,

you will hear short beeps whenever you press

the >N button, and a long beep whenever

you press the xSTOP button.

VOL

xSTOP

>N

spea

k

er

x

Connect firmly to i

Connect

firmly to i

NPLAY

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Right

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\030GET.fm]

15-GB

To listen in stereo

Connect the supplied headphones with a remote control to the i jack on the recorder.

If the play does not start

Make sure the recorder is not locked (pages 9

and 41).

To locate a point quickly

Use the EASY SEARCH +/– buttons (page 28).

z

Playback will switch automatically between

stereo and monaural according to the sound

source.

Notes

• The sound may skip during playback when the

recorder is exposed to continuous vibration,

such as while jogging.

• If the power supply is disrupted (i.e. the

batteries are removed or become exhausted or

the optional AC power adaptor is

disconnected) when the recorder is operating,

the lid may not open until the power is

restored.

To Operation on the recorder Operation on the remote

control (Beeps in the

headphones)

Find the beginning of

the current track or a

previous track

1)

Press .REVIEW/AMS.

Press .REVIEW/AMS

repeatedly until you reach the

beginning of the desired track.

Press .. (Three short beeps)

Press . repeatedly until you

reach the beginning of the

desired track.

Find the beginning of

the next track

2)

Press >CUE/AMS. Press >N. (Two short

beeps)

Pause Press XPAUSE. Press

XPAUSE again to resume

play.

Press X on the remote control.

(Continuous short beeps) Press

X again to resume play.

Go backwards while

playing

Press and hold .REVIEW/

AMS.

Press and hold ..

Go forward while

playing

Press and hold >CUE/

AMS.

Press and hold >N.

Remove the MD Press xSTOP and open the

lid.

3)

Press x. (One short beep)

1)

If you press .REVIEW/AMS during the first track of the disc, the recorder goes to the beginning

of the last track on the disc.

2)

If you press >CUE/AMS during the last track of the disc, the recorder goes to the beginning of the

first track on the disc.

3)

Once you open the lid, the point to start play will change to the beginning of the first track.

16-GB

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:L0-Left

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\040OPE.fm]

Various ways of recording

Recording for long

times

Select each recording mode according to

the recording time that you want.

Stereo recording is possible at 2 times

(LP2) or 4 times (LP4) the normal

(stereo) recording time. Monaural

recording at 2 times normal recording

speed is also possible.

MDs recorded in monaural, LP2

stereo, or LP4 stereo mode can be

played back only on MD players or

recorders with monaural, LP2

stereo, or LP4 stereo playback

mode.

1 Insert a recordable disc.

2 Press REC MODE repeatedly until

desired recording mode lights up in

the display.

Each time you press the button, A

changes as follows.

3 Press zREC.

For other operations on recording, see

“Recording an MD right away!”

(page 11).

To stop recording, press x.

The recorder switches back to stereo

recording when you record the next time.

z

• Audio components that support the LP2 stereo

or LP4 stereo modes are indicated by the

or logo marks.

• The recording mode can be changed during

recording pause. When you change the

recording mode, a track mark is automatically

added at that point.

Recording

mode

1)

A Recording

time

3)

Stereo STEREO approx. 80

min.

zREC

REC MODE

007

30:03

A

LP2 stereo LP2 approx. 160

min.

LP4 stereo LP4 approx. 320

min.

Monaural

2)

MONO approx. 160

min.

1)

For better sound quality, record in normal

stereo or LP2 stereo mode.

2)

If you record a stereo source in monaural, the

sounds from left and right will be mixed.

3)

When using an 80-minute recordable MD

Recording

mode

1)

A Recording

time

3)

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Right

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\040OPE.fm]

17-GB

Notes

• “LP:” will be added at the beginning of the

track name of a track recorded in MDLP

mode.

• It is recommended that you use the supplied

AC power adaptor for long recordings.

• During monaural recording of a stereo sound

source connected through the digital (optical)

input jack, you can still monitor the recorded

sound in stereo by using headphones or

earphones connected to the i/LINE OUT

jack.

• When you record in LP4 mode, momentary

noise may be produced on very rare occasions

with certain sound sources. This is because of

the special digital audio compression

technology that enables a recording time 4

times longer than normal. If noise is produced,

it is recommended that you record in normal

stereo or LP2 mode to obtain better sound

quality.

VOR (Voice Operated

Recording)

VOR causes the recorder to automatically

record when there is sound, and to pause

when there is no sound. This allows you

to record without troublesome button

operations.

1 Insert a recordable disc and slide MIC

SENS to H (high) or L (low).

2 Press REC MODE repeatedly until

“STEREO”, “LP2”, “LP4”, or

“MONO” lights up in the display.

For details on the recording mode, see

“Recording for long times” (page 16).

3 Press zREC.

4 Press VOR.

VOR turns on.

“VOR” appears in the display and the

VOR indicator lights up when the

recorder is recording. Both “VOR”

and the VOR indicator flash when the

recorder is not recording.

To cancel VOR while recording

Press VOR again.

“VOR” and the VOR indicator goes off

and the recorder changes to normal

recording mode.

z

• VOR automatically turns off when you press

the xSTOP button to stop recording.

• You can change the recording mode when

VOR is on and the recorder is not recording

(while “VOR” and VOR indicator flash). A

track mark is added each time you press the

REC MODE button.

Notes

• You cannot record with the built-in

microphones while an optional microphone is

connected to the MIC (PLUG IN POWER)

jack or an optical cable (not supplied) is

connected to the LINE IN (OPTICAL) jack.

• VOR is sensitive to the surrounding sound

conditions. Set the MIC SENS switch to H or

L to suit the conditions. If you cannot get the

desired recording results, cancel VOR and

record in manual mode.

• Power from the batteries is consumed as long

as VOR is on, even when recording is not

taking place (i.e., when “VOR” and the VOR

indicator flash.)

VOR

indicator

built-in

microphones

MIC SENS

zREC

REC

MODE

built-in

microphones

18-GB

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Left

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\040OPE.fm]

Recording from a

microphone

Connect a stereo microphone (ECM-717,

etc.; not supplied) to the MIC (PLUG IN

POWER) jack. The recorder input

automatically switches to the externally

connected microphone input.

1 Insert a recordable disc and slide MIC

SENS to H (high) or L (low).

2 Press REC MODE repeatedly until

“STEREO”, “LP2”, “LP4”, or

“MONO” lights up in the display.

For details on the recording mode, see

“Recording for long times” (page 16).

3 Press zREC.

For other operations on recording, see

“Recording an MD right away!”

(page 11).

z

When using a plug-in-power microphone, no

battery is needed for the microphone since

power is supplied by the recorder.

If you are using the optional stereo microphone

ECM-717, set the switch on the microphone to

OFF to allow the recorder to provide power to

the microphone. It is recommended that you set

the switch on the microphone to OFF during

use.

Notes

• You cannot record through the externally

connected microphone while an optical cable

is connected to the LINE IN (OPTICAL) jack.

The recorder automatically selects the

recorder input in the following order of

priority; optical input, externally connected

microphone input, analog (line) input, and

built-in microphones input.

• The microphone may pick up the operating

sound of the recorder itself (such as the sound

of the motor). Use the microphone away from

the recorder in such cases. Do not use a

microphone with a short connector, as this

may cause the operating sound of the recorder

to be picked up.

to MIC (PLUG IN

POWER)

Stereo

microphone

(not supplied)

REC MODE

MIC SENS

zREC

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Right

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\040OPE.fm]

19-GB

Recording from externally connected equipment

The input jack of this recorder works as both digital and analog input jacks. Connect the

recorder to a CD player or a cassette recorder using either digital (optical) input or analog

(line) input. To record, see “Recording with digital (optical) input (optical cable required)”

(page 20) to record using digital (optical) input and “Recording with analog (line) input

(line cable required)” (page 21) to record using analog (line) input.

LINE IN (OPTICAL) jack is for both digital and analog input.

The recorder automatically recognizes the type of line cable and switches to digital or analog input.

Difference between digital (optical) and analog (line) inputs

Note

Track marks may be copied incorrectly:

• when you record from some CD players or multi disc players using digital (optical) input.

• when the source is in shuffle or program play mode while recording using digital (optical) input. In

this case, play the source in normal play mode.

• when recording BS or CS programs through digital (optical) input.

Difference Digital (optical) input Analog (line) input

Connectable

source

Equipment with an digital (optical)

output jack

Equipment with an analog

(line) output jack

Usable cord Optical cable (with an optical or an

optical-mini plug)(page 20)

Line cable (with 2 phono plugs

or a stereo-mini plug)(page 21)

Signal from the

source

Digital Analog

Even when a digital source

(such as a CD) is connected, the

signal sent to the recorder is

analog.

Recorded track

numbers

Marked (copied) automatically

• at the same positions as the source

(when the sound source is a CD or

an MD).

• after more than 2 seconds of blank

or low-level segment (with a sound

source other than a CD or an MD)

(page 53).

• when the recorder is paused while

recording (the recorder pauses

automatically when it encounters a

section with no audio signal for 3

seconds or more) (page 53).

You can erase unnecessary marks

after recording. (“Erasing a track

mark”, page 33).

Marked automatically

• after more than 2 seconds of

blank or low-level segment.

• when the recorder is paused

while recording.

You can erase unnecessary

marks after recording (“Erasing

a track mark”, page 33).

Recorded

sound level

Same as the source. Adjusted automatically.

20-GB

model name1[MZ-B100] model name2[MZ------]

[3-235-455-11(1)]

masterpage:Left

filename[C:\SON_SSIAJX_102\MZ-B100\3235455121GBESRU\02GB-

MZB100UCE\040OPE.fm]

Recording with digital

(optical) input (optical cable

required)

Connect to a digital source using an

optical cable (not supplied) to make

digital recordings. Digital recording is

possible even from digital equipment with

different sampling rates, such as a DAT

deck or a BS tuner, using the built-in

sampling rate converter.

1 Insert a recordable disc.

2 Press REC MODE repeatedly until

“STEREO”, “LP2”, “LP4”, or

“MONO” lights up in the display.

For details on the recording mode, see

“Recording for long times” (page 16).

3 Press zREC.

“REC” appears in the display, the

REC indicator lights up, and the

recording starts.

4 Play the source sound.

For other operations on recording, see

“Recording an MD right away!”

(page 11).

z

When recording from digital media, track

marks in the original are copied automatically

to the MD.

Notes

• You can make a digital recording with an

optical cable only from an optical type output.

• When recording from a portable CD player,

play it on AC power and disable the anti-skip

function (such as ESP*).

• When recording from a portable CD player,

pause the CD player before doing the

recording procedure.

• Digital output may be disabled on some

portable CD players when the AC power

adaptor is not connected to the player.

• A track mark is added at the point where you

press the XPAUSE button again to resume

recording while pausing recording; thus the

remainder of the track will be counted as a

new track.

∗ Electronic Shock Protection

POC-15AB etc.

(not supplied)

POC-15B etc.

(not supplied)

to LINE IN

(OPTICAL)

Optical

plug

Optical

mini-

plug

CD player, MD

player, digital

amplifier, etc.

Portable CD

player, etc.

zREC

REC

indicator

REC

MODE

Страница загружается ...

Sony MZ-B100 Руководство пользователя

Sony MZ-B100 Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов