DeWalt DCD999 Руководство пользователя

DCD999

English (original instructions) 3

Pусский (перевод соригинала инструкции) 14

Українська (переклад з оригінальної інструкції) 31

Fig. A

Fig. B

XXXX XX XX

Fig.C Fig.D

Fig.E

ENGLISH

aWARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.

EC‑Declaration of Conformity

Machinery Directive

Impact Drill

DCD999

DEWALT declares that these products described under

Technical Data are in compliance with:

2006/42/EC, EN60745‑1:2009+A11:2010, EN60745‑2‑1:2010.

These products also comply with Directive 2014/30/EU and

2011/65/EU. For more information, please contact DEWALT at

the following address or refer to the back of themanual.

The undersigned is responsible for compilation of the technical

file and makes this declaration on behalf ofDEWALT.

Markus Rompel

Vice‑President Engineering, PTE‑Europe

DEWALT, Richard‑Klinger‑Straße 11,

65510, Idstein, Germany

19.08.2020

The vibration and/or noise emission level given in this information

sheet has been measured in accordance with a standardised test

given in EN60745

and may be used to compare one tool with

another. It may be used for a preliminary assessment ofexposure.

WARNING: The declared vibration and/or noise emission

level represents the main applications of the tool. However

if the tool is used for different applications, with different

accessories or poorly maintained, the vibration and/or

noise emission may differ. This may significantly increase

the exposure level over the total workingperiod.

An estimation of the level of exposure to vibration and/or

noise should also take into account the times when the tool

is switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total workingperiod.

Identify additional safety measures to protect the operator

from the effects of vibration and/or noise such as: maintain

the tool and the accessories, keep the hands warm

(relevant for vibration), organisation of workpatterns.

DCD999

Voltage VDC 18

Type 1

Battery type Li-Ion

No load speed Drill, Driver/Hammer

1st gear min-1 0–450/500

2nd gear 0–1300/1500

3rd gear 0–2000/2250

Impact rate

1st gear min-1 0–8500

2nd gear 0–25500

3rd gear 0–38250

Max. torque (hard/soft) DCB546 DCB547

hard Nm 112 126

soft Nm 66 67

Chuck capacity mm 1.5–13

Maximum drilling capcity

Wood mm 55

Metal 15

Masonry 13

Weight (without battery pack) kg 1.61

Noise values and vibration values (triax vector sum) according to EN60745-2-1:

LPA (emission sound pressure level) dB(A) 94

LWA (sound power level) dB(A) 105

K (uncertainty for the given

sound level)

dB(A) 3

Drilling into metal

Vibration emission value a

h,D

= m/s22.7

Uncertainty K = m/s21.5

Impact drilling

Vibration emission value a

h,ID

= m/s212.5

Uncertainty K = m/s21.5

Screwdriving

Vibration emission value a

= m/s2< 2.5

Uncertainty K = m/s21.5

DCB184 DCB546 DCB547

Power UWO 860 1219 1296

Congratulations!

You have chosen a BernerDEWALT tool. Years of experience,

thorough product development and innovation make

BernerDEWALT one of the most reliable partners for professional

power toolusers.

Technical Data

IMPACT DRILL

DCD999

ENGLISH

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non‑skid safety shoes, hard hat or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off‑position before connecting to power

source and/or battery pack, picking up or carrying

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTUREREFERENCE

The term “power tool” in the warnings refers to your

mains‑operated (corded) power tool or battery‑operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Denotes risk of electricshock.

Denotes risk offire.

Batteries Chargers/Charge Times (Minutes)

Cat # VDC Ah Weight (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB116 DCB117 DCB118 DCB132 DCB119

DCB546 18/54 6.0/2.0 1.05 60 270 170 140 90 80 40 60 90 X

DCB547 18/54 9.0/3.0 1.46 75* 420 270 220 135* 110* 60 75* 135* X

DCB548 18/54 12.0/4.0 1.44 120 540 350 300 180 150 80 120 180 X

DCB181 18 1.5 0.35 22 70 45 35 22 22 22 22 22 45

DCB182 18 4.0 0.61 60/40** 185 120 100 60 60/45** 60/40** 60/40** 60 120

DCB183/B/G 18 2.0 0.40 30 90 60 50 30 30 30 30 30 60

DCB184/B/G 18 5.0 0.62 75/50** 240 150 120 75 75/60** 75/50** 75/50** 75 150

DCB185 18 1.3 0.35 22 60 40 30 22 22 22 22 22 40

DCB187 18 3.0 0.54 45 140 90 70 45 45 45 45 45 90

DCB189 18 4.0 0.54 60 185 120 100 60 60 60 60 60 120

*Date code 201811475B or later

**Date code 201536 or later

ENGLISH

Additional Specific Safety Rules for Drills/

Drivers/Hammerdrills

• Wear ear protectors when impact drilling. Exposure to

noise can cause hearingloss.

• Use the auxiliary handles, if supplied with the tool. Loss

of control can cause personalinjury.

• Brace the tool properly before use. This tool produces a

high output torque and without properly bracing the tool

during operation, loss of control may occur resulting in

personalinjury.

• Hold the power tool by insulated gripping surfaces when

performing an operation where the cutting accessory

may contact hidden wiring. Cutting accessory or fasteners

contacting a “live” wire may make exposed metal parts of the

power tool “live” and could give the operator an electricshock.

surfaces do not allow for safe handling and control of the

tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

e ) Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk

ofinjury.

f ) Do not expose a battery pack or tool to fire or

excessive temperature. Exposure to fire or temperature

above 130°C may causeexplosion.

g ) Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging

improperly or at temperatures outside the specified range

may damage the battery and increase the risk offire.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be

caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust‑relatedhazards.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe

injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the

power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

ENGLISH

Mains Plug Replacement

(U.K.& Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.

WARNING: No connection is to be made to the

earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 3A.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm2; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

Important Safety Instructions for All

BatteryChargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.

WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.

WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.

CAUTION: Burn hazard. To reduce the risk of injury,

charge only DEWALT rechargeable batteries. Other

types of batteries may burst causing personal injury

anddamage.

CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting toclean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging DEWALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

Chargers

DEWALT chargers require no adjustment and are designed to be

as easy as possible tooperate.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

iYour DEWALT charger is double insulated in

accordance with EN60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced only by

DEWALT or an authorised serviceorganisation.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

SAVE THESE INSTRUCTIONS

Safety Instructions When Using Long

Drill Bits

• Never operate at higher speed than the maximum

speed rating of the drill bit. At higher speeds, the bit is likely

to bend if allowed to rotate freely without contacting the

workpiece, resulting in personalinjury.

• Always start drilling at low speed and with the bit tip

in contact with the workpiece. At higher speeds, the bit is

likely to bend if allowed to rotate freely without contacting the

workpiece, resulting in personalinjury.

• Apply pressure only in direct line with the bit and do not

apply excessive pressure. Bits can bend causing breakage or

loss of control, resulting in personalinjury.

• Use clamps or other practical way to secure and support

the workpiece to a stable platform. Holding the work by

hand or against your body is unstable and may lead to loss

ofcontrol.

• Wear ear protectors when hammering for extended

periods of time. Prolonged exposure to high intensity noise

can cause hearing loss. Temporary hearing loss or serious ear

drum damage may result from high sound levels generated

byhammerdrilling.

• Wear safety goggles or other eye protection. Hammering

and drilling operations cause chips to fly. Flying particles can

cause permanent eyedamage.

• Hammer bits and tools get hot during operation. Wear

gloves when touchingthem.

ENGLISH

Charge Indicators

FCharging I

GFully Charged J

HHot/Cold Pack Delay* K

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing tolight.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed

to cool the battery pack. The fan will turn on automatically

when the battery pack needs to be cooled. Never operate the

charger if the fan does not operate properly or if ventilation slots

are blocked. Do not permit foreign objects to enter the interior

of thecharger.

Electronic Protection System

XR Li‑Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium‑ion battery

pack on the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord, the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard

230V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig.B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack 1 into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button 2 on the batterypack.

NOTE: To ensure maximum performance and life of lithium‑ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

ENGLISH

may result. Damaged battery packs should be returned to

service centre forrecycling.

WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.

CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation

WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from

materials that could contact them and cause a short

circuit. NOTE: Lithium‑ion batteries should not be put in

checkedbaggage.

DEWALT batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road

(ADR). Lithium‑ion cells and batteries have been tested to

section 38.3of the UN Recommendations on the Transport of

Dangerous Goods Manual of Tests andCriteria.

In most instances, shipping a DEWALT battery pack will be

excepted from being classified as a fully regulated Class

9Hazardous Material. In general, only shipments containing a

lithium‑ion battery with an energy rating greater than 100Watt

Hours (Wh) will require being shipped as fully regulated Class 9.

All lithium‑ion batteries have the Watt Hour rating marked on

the pack. Furthermore, due to regulation complexities, DEWALT

does not recommend air shipping lithium‑ion battery packs

alone regardless of Watt Hour rating. Shipments of tools with

batteries (combo kits) can be air shipped as excepted if the Watt

Hour rating of the battery pack is no greater than 100Wh.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Transporting the FLEXVOLTTM Battery

The DEWALT FLEXVOLTTM battery has two modes: Use

andTransport.

Battery Packs

Important Safety Instructions for All

BatteryPacks

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non‑compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in DEWALTchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in locations

where the temperature may fall below 4˚C (39.2˚F)

(such as outside sheds or metal buildings in winter), or

reach or exceed 40˚C (104˚F) (such as outside sheds or

metal buildings insummer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium‑ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.

WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.

WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non‑metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

ENGLISH

Markings on Tool

The following pictograms are shown on the tool:

a Read instruction manual beforeuse.

Package Contents

The package contains:

1 Brushless cordless hammerdrill

1 Kitbox

1 Charger

1 Side handle

1 Magnetic bit holder (Optional accessory)

1 Belt hook (Optional accessory)

1 Li‑Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1, Y1 models)

2 Li‑Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2, Y2 models)

3 Li‑Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3, Y3 models)

1 Instruction manual

NOTE: Battery packs, chargers and kitboxes are not included

with N models. Battery packs and chargers are not included with

NT models. Bmodels include Bluetooth® batterypacks.

NOTE: The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth®, SIG, Inc. and any use of

such marks by DEWALT is under license. Other trademarks and

trade names are those of their respectiveowners.

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Battery Type

The following tools operate on a 18 volt battery pack: DCD999.

These battery packs may be used: DCB181, DCB182, DCB183,

DCB183B, DCB183G, DCB184, DCB184B, DCB184G, DCB185,

DCB187, DCB189DCB546, DCB547, DCB548. Refer to Technical

Data for moreinformation.

u Charge only between 4˚C and 40˚C.

v Only for indooruse.

x Discard the battery pack with due care for

theenvironment.

y Charge DEWALT battery packs only with designated

DEWALT chargers. Charging battery packs other than

the designated DEWALT batteries with a DEWALT

charger may make them burst or lead to other

dangeroussituations.

z Do not incinerate the batterypack.

B USE (without transport cap). Example: Wh rating

indicates 108Wh (1battery with 108Wh).

A TRANSPORT (with built‑in transport cap). Example: Wh

rating indicates 3x 36Wh (3batteries of 36Wh).

Use Mode: When the FLEXVOLTTM battery stands alone or is in

a DEWALT 18V product, it will operate as an 18V battery. When

the FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries)

product, it will operate as a 54Vbattery.

Transport Mode: When the cap is attached to the FLEXVOLTTM

battery, the battery is in Transport mode. Keep the cap

forshipping.

When in Transport mode, strings

of cells are electrically

disconnected within the pack

resulting in 3batteries with a

lower Watt hour (Wh) rating as compared to 1battery with a

higher Watt hour rating. This increased quantity of 3batteries

with the lower Watt hour rating can exempt the pack from

certain shipping regulations that are imposed upon the higher

Watt hour batteries.

For example, the Transport

Wh rating might indicate

3x36Wh, meaning

3batteries of 36Wh each.

The Use Wh rating might

indicate 108Wh (1batteryimplied).

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be recharged

beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the

labels on the charger and the battery pack may show the

followingpictographs:

LRead instruction manual beforeuse.

p See Technical Data for chargingtime.

q Do not probe with conductiveobjects.

r Do not charge damaged batterypacks.

s Do not expose towater.

t Have defective cords replacedimmediately

Example of Use and Transport Label Marking

ENGLISH

Variable Speed Trigger Switch (Fig. A)

To turn the tool on, squeeze the variable speed

triggerswitch3. To turn the tool off, release the trigger switch.

Belt Hook and Magnetic Bit Holder (Fig. A)

Optional Accessories

WARNING: To reduce the risk of serious personal

injury, ONLY use the tool's belt hook to hang the

tool from a work belt. DO NOT use the belt hook for

tethering or securing the tool to a person or object during

use. DO NOT suspend tool overhead or suspend objects

from the belthook.

WARNING: To reduce the risk of serious personal

injury, ensure the screw holding the belt hook issecure.

CAUTION: To reduce the risk of personal injury or

damage, DO NOT use the belt hook to hang the drill

while using as aspotlight.

IMPORTANT: When attaching or replacing the belt hook11 or

magnetic bit holder13 , use only the mounting screw12 that

is provided. Be sure to securely tighten thescrew.

The belt hook and magnetic bit holder can be be attached

to either side of the tool using only the screw provided, to

accommodate left‑ or right‑ handed users. If the hook or

magnetic bit holder is not desired at all, it can be removed from

thetool.

Inserting and Removing the Battery Pack

from the Tool (Fig. B)

NOTE: Make sure your battery pack 1 is fullycharged.

To Install the Battery Pack into the Tool Handle

1. Align the battery pack 1 with the rails inside the tool’s

handle (Fig. B).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button 2 and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig.B)

Some DEWALT battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button17. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level

of charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end‑userapplication.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

WARNING: Use only DEWALT battery packs andchargers.

Description (Fig. A)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

Components

1 Battery pack

2 Battery release button

3 Variable speed trigger switch

4 Forward/reverse control button

5 Torque adjustment collar

6 Keyless chuck

7 Chuck sleeve

8 Speed selector

9 Worklight

10 Worklight switch

11 Belt hook (Optional accessory)

12 Mounting screw

13 Bit holder (Optional accessory)

14 Side handle

15 Main handle

Intended Use

These hammerdrills are designed for professional drilling,

percussion drilling and screwdrivingapplications.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

These drills/drivers/hammerdrills are professional powertools.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Date Code Position (Fig.B)

The date code 6, which also includes the year of manufacture,

is printed into thehousing.

Example:

2021XX XX

Year and Week of Manufacture

n Visible radiation. Do not stare intolight.

ENGLISH

Keyless Single Sleeve Chuck (Fig. C)

WARNING: Do not attempt to tighten drill bits (or

any other accessory) by gripping the front part of the

chuck and turning the tool on. Damage to the chuck

and personal injury may result. Always lock off trigger

switch and remove the battery from the tool when

changingacces sories.

WARNING: Always ensure the bit is secure before starting

the tool. A loose bit may eject from tool causing possible

personalinjury.

Your tool features a keyless chuck6 with one rotating chuck

sleeve7 for one‑handed operation of the chuck. To insert a drill

bit or other accessory, follow thesesteps.

LED Worklight (Fig. E)

The LED worklight9 and its worklight switch10 are located on

the foot of the tool. The worklight is activated when the trigger

switch is depressed. The low, medium, and spotlight modes can

be changed by moving the switch on the foot of the tool. If the

trigger switch remains depressed, the worklight will remain on

in allmodes.

When on low and medium settings, the beam will automatically

turn off 20 seconds after the trigger switch isreleased.

Spotlight Mode

The high setting is the spotlight mode. The spotlight will run

for 20minutes after the trigger switch is released. Two minutes

before the spotlight will shut off, it will flash twice and then dim.

To avoid the spotlight shutting off, lightly tap the triggerswitch.

WARNING: While using the worklight in medium or

spotlight mode, do not stare at the light or place the drill in

a position which may cause anyone to stare into the light.

Serious eye injury couldresult.

CAUTION: When using the tool as a spotlight, be sure

it is secured on a stable surface where it will not cause a

tripping or fallinghazard.

CAUTION: Remove all accessories from the chuck before

using the drill as a spotlight. Personal injury or property

damage couldresult.

Low Battery Warning

When in spotlight mode and the battery is nearing complete

discharge, the spotlight will flash twice and then dim. After two

minutes, the battery will be completely discharged and the

drill will immediately shut down. At this point, replace with a

chargedbattery.

WARNING: To reduce the risk of injury, always have a

back‑up battery or secondary lighting available if the

situation warrantsit.

NOTE: Do not change gears when the tool is running. Always

allow the drill to come to a complete stop before changing

gears. If you have trouble changing gears, make sure that the

gear shifter is engaged in one of the three speedsettings.

If the speed shifter becomes stuck or is difficult to select the

desired gear, pull the variable speed trigger switch3 to rotate

the motor, then select thegear.

Three‑Speed Gearing (Fig. A)

The three‑speed feature of your tool allows you to shift gears

for greater versatility. To select speed 1 (highest torque setting),

turn the tool off and permit it to stop. Slide the gear shifter8

all the way forward. Speed 2 (middle torque and speed setting)

is in the middle position. Speed 3 (highest speed setting) is to

therear.

Torque Adjustment Collar/Electronic Clutch

(Fig. A)

Your tool has an electronic adjustable torque screwdriver

mechanism for driving and removing a wide array of fasteners.

Circling the torque adjustment collar5 are numbers. These

numbers are used to set the clutch to deliver a torque range.

The higher the number on the collar, the higher the torque and

the larger the fastener which can be driven. To select any of the

numbers, rotate until the desired number aligns with thearrow.

WARNING: When the torque adjustment collar is in the

drill or hammerdrill positions, the drill will not clutch. The

drill may stall if overloaded, causing a suddentwist.

Forward/Reverse Control Button (Fig. A)

A forward/reverse control button4 determines the direction of

the tool and also serves as a lock‑offbutton.

To select forward rotation, release the trigger switch and

depress the for ward/re verse control button on the right side of

thetool.

To select reverse, release the trigger switch and depress the

forward/reverse control button on the left side of thetool.

The centre position of the control button locks the tool in the off

position. When changing the position of the control button, be

sure the trigger isreleased.

NOTE: The first time the tool is run after changing the direction

of rotation, you may hear a click on start up. This is normal and

does not indicate aproblem.

Side Handle (Fig. A, D)

WARNING: To reduce the risk of personal injury, ALWAYS

operate the tool with the side handle properly installed.

Failure to do so may result in the side handle slipping

during tool operation and subsequent loss of control. Hold

tool with both hands to maximizecontrol.

The side handle14 clamps to the front of the gear case and

may be rotated 360˚ to permit right‑ or left‑hand use. Side

handle must be tightened sufficiently to resist the twisting

action of the tool if the accessory binds or stalls. Be sure to grip

the side handle at the far end to control the tool during astall.

If model is not equipped with side handle, grip drill with one

hand on the handle and one hand on the batterypack.

NOTE: Side handle comes equipped on allmodels.

Your tool is equipped with a brake. The chuck will stop as soon

as the trigger switch is fullyreleased.

NOTE: Continuous use in variable speed range is not

recommended. It may damage the switch and should

beavoided.

ENGLISH

MAINTENANCE

Your power tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regularcleaning.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

The charger and battery pack are notserviceable.

Hammerdrill Operation (Fig. A)

1. Select the desired speed/torque range using the gear shifter

to match the speed and torque to the planned operation.

Set the torque adjustment collar 5 to the hammersymbol.

2. Select the high speed 3 setting by sliding the gear shifter 8

back (away form the chuck).

3. When drilling, use just enough force on the hammer to

keep it from bouncing excessively. Prolonged and too much

force on the hammer will cause slower drilling speeds and

potentialoverheating.

4. Drill straight, keeping the bit at a right angle to the work. Do

not exert side pressure on the bit when drilling as this will

cause clogging of the bit flutes and a slower drillingspeed.

5. When drilling deep holes, if the hammer speed starts to

drop off, pull the bit partially out of the hole with the tool

still running to help clear debris from thehole.

6. For masonry, use carbide‑tipped bits or masonry bits. A

smooth, even flow of dust indicates the proper drillingrate.

Drill Operation (Fig. A)

WARNING: TO REDUCE THE RISK OF PERSONAL

INJURY, ALWAYS ensure workpiece is anchored or

clamped firmly. If drilling thin material, use a wood “back‑

up” block to prevent damage to thematerial.

1. Select the desired speed/torque range using the gear

shifter8 to match the speed and torque to the planned

operation. Set the torque adjustment collar5 to the

drillsymbol.

2. For WOOD, use twist bits, spade bits, power auger bits or

hole saws. For METAL, use high‑speed steel twist drill bits

or hole saws. Use a cutting lubricant when drilling metals.

The exceptions are cast iron and brass which should be

drilleddry.

3. Always apply pressure in a straight line with the bit. Use

enough pressure to keep the drill bit biting, but do not push

hard enough to stall the motor or deflect thebit.

4. Hold tool firmly with both hands to control the twisting

action of thedrill.

5. IF DRILL STALLS, it is usually because it is being

overloaded. RELEASE TRIGGER IMMEDIATELY, remove

drill bit from work, and determine cause of stalling. DO NOT

CLICK TRIGGER OFF AND ON IN AN ATTEMPT TO START

A STALLED DRILL – THIS CAN DAMAGE THEDRILL.

6. Keep the motor running when pulling the bit back out of a

drilled hole. This will help preventjamming.

Screwdriver Operation (Fig. A)

1. Select the desired speed/torque range using the

three‑speed gear shifter8 on the top of the tool. If using

the torque adjustment collar5, initially set the three‑speed

gear shifter to speed 2or 3. This ensures effective control

over the fastener allowing the screw to be seated correctly

and set to specification. Speed 1will provide the same

clutching torque as speeds 2and 3. However, for optimum

performance of the electronic clutch, speeds 2and

3arepreferred.

NOTE: Use the lowest torque setting (1) first and increase

the number through to the highest setting (11) to seat the

fastener at the desired depth. The lower the number, the

lower the torqueoutput.

2. Reset the torque adjustment collar5 to the appropriate

number setting for the torque desired. Make a few practice

runs in scrap or unseen areas to determine the proper

position of the torque adjustmentcollar.

NOTE: The torque adjustment collar may be set to any number

at anytime.

Proper Hand Position (Fig. D)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a suddenreaction.

Proper hand position requires one hand on the main

handle 15, with the other hand on the side handle14 to

control the twisting action of thedrill.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and

applicableregulations.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

1. Turn tool off and remove the battery pack.

2. Grasp the black sleeve of the chuck with one hand and

use the other hand to secure the tool. Rotate the sleeve

anticlockwise (as viewed from the front) far enough to

accept the desiredaccessory.

3. Insert the accessory about 19mm into the chuck and

tighten securely by rotating the chuck sleeve clockwise

with one hand while holding the tool with the other hand.

Continue to rotate the chuck sleeve until several ratchet

clicks are heard to ensure full grippingpower.

NOTE: Be sure to tighten chuck with one hand on

the chuck sleeve and one hand holding the tool for

maximumtightness.

To release the accessory, repeat steps 1and 2above.

ENGLISH

Protecting the Environment

wSeparate collection. Products and batteries marked

with this symbol must not be disposed of with

normal householdwaste.

Products and batteries contain materials that

can be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

ourenvironment:

• Run the battery pack down completely, then remove it from

thetool.

• Li‑Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

Optional Accessories

WARNING: Since accessories, other than those offered

by BernerDEWALT, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only BernerDEWALT

recommended accessories should be used with

thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Cleaning

WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals

for cleaning the non‑metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Lubrication

Your power tool requires no additionallubrication.

PУССКИЙ

Декларация о соответствии нормам ЕС

Директива по механическому оборудованию

Ударная дрель

DCD999

DEWALT заявляет, что продукция, описанная в разделе

«Технические характеристики» соответствует:

2006/42/EC, EN60745‑1:2009+A11:2010, EN60745‑2‑1:2010.

Значение шумовой эмиссии и/или эмиссии вибрации,

указанное в данном справочном листке, было получено

в соответствии со стандартным тестом, приведенным

в EN60745, и может использоваться для сравнения

инструментов. Кроме того, оно может использоваться для

предварительной оценки воздействиявибрации.

ОСТОРОЖНО! Заявленное значение шумовой

эмиссии и/или эмиссии вибрации относится к

основным областям применения инструмента.

Однако, если инструмент используется для

различных целей, с различными дополнительными

принадлежностями или при ненадлежащем уходе, то

уровень шума и/или вибрации может измениться.

Это может привести к значительному увеличению

уровня воздействия вибрации в течение всего

рабочегопериода.

При расчете приблизительного значения уровня

воздействия шума и/или вибрации также

необходимо учитывать время, когда инструмент

выключен или то время, когда он работает

на холостом ходу. Это может привести к

значительному снижению уровня воздействия

вибрации в течение всего рабочегопериода.

Определите дополнительные меры техники

безопасности для защиты оператора от

воздействия шума и/или вибрации, а именно:

поддержание инструмента и дополнительных

принадлежностей в рабочем состоянии, создание

комфортных условий работы (соответствующих

вибрации), хорошая организация рабочегоместа.

DCD999

Погрешность K = м/с21,5

Заворачивание

Значение вибрационного

воздействия a

м/с2< 2,5

Погрешность K = м/с21,5

DCB184 DCB546 DCB547

Мощность UWO 860 1219 1296

DCD999

Напряжение Впост. тока 18

Тип 1

Тип батареи Ионно-литиевая

Скорость без нагрузки Дрель, шуруповерт/

ударная дрель

1-я скорость об/мин. 0-450/500

2-я скорость 0-1300/1500

3-я скорость 0-2000/2250

Скорость удара

1-я скорость уд/мин. 0–8500

2-я скорость 0–25500

3-я скорость 0–38250

Макс. крутящий момент (жесткий/

мягкий)

DCB546 DCB547

жесткий Нм 112 126

мягкий Нм 66 67

Диаметр патрона мм 1,5–13

Макс. скорость сверления

Древесина мм 55

Металл 15

Кирпичная кладка 13

Вес (без аккумуляторной батареи) кг 1,61

Значения шума и вибрации (сумма векторов в трех плоскостях) в

соответствии с EN60745-2-1:

LPA (уровень звукового давления) дБ(A) 94

LWA (уровень акустической

мощности)

дБ(A) 105

K (погрешность для заданного

уровня мощности)

дБ(A) 3

Сверление металла

Значение вибрационного

воздействия a

h, D

м/с22,7

Погрешность K = м/с21,5

Сверление с ударом

Значение вибрационного

воздействия a

h, ID

м/с212,5

Поздравляем!

Вы приобрели инструмент DEWALT. Многолетний опыт,

тщательная разработка изделий иинновации делают

компанию DEWALT одним из самых надёжных партнеров для

пользователей профессиональногоэлектроинструмента.

Технические характеристики

УДАРНАЯ ДРЕЛЬ

DCD999

PУССКИЙ

ОБЩИЕ ПРАВИЛА ТЕХНИКИ

БЕЗОПАСНОСТИ ПРИ ИСПОЛЬЗОВАНИИ

ЭЛЕКТРОИНСТРУМЕНТОВ

ВНИМАНИЕ: Прочитайте ипросмотрите

все предупреждения, инструкции,

иллюстрации испецификации по данному

электроинструменту. Несоблюдение всех

приведенных ниже инструкций может стать

причиной поражения электрическим током,

возгорания и/или тяжелойтравмы.

СОХРАНИТЕ ВСЕ ИНСТРУКЦИИ ДЛЯ

ПОСЛЕДУЮЩЕГОИСПОЛЬЗОВАНИЯ

Термин «электроинструмент» впредупреждениях

относится кработающим от сети

(проводным) электроинструментам или

работающим от аккумуляторной батареи

(беспроводным)электроинструментам.

1) Безопасность на рабочем месте

a ) Следите за чистотой ихорошим освещением

на рабочем месте. Захламленное или плохо

освещенное рабочее место может стать причиной

несчастногослучая.

b ) Запрещается работать

сэлектроинструментами во

взрывоопасных местах, например, вблизи

легковоспламеняющихся жидкостей, газов

ипыли. Искры, которые появляются при

работе электроинструментов могут привести

квоспламенению пыли илипаров.

ПОЯСНЕНИЕ: Указывает на практики,

использование которых не связано

сполучением травмы, но если ими пренебречь,

могут привести кпорчеимущества.

Указывает на риск поражения электрическимтоком.

Указывает на рисквозгорания.

aВНИМАНИЕ: Во избежание риска получения травм

ознакомьтесь синструкцией.

Обозначения: правила техники

безопасности

Ниже описывается уровень опасности, обозначаемый

каждым из предупреждений. Прочитайте руководство

иобратите внимание на данныесимволы.

ОПАСНО: Обозначает опасную ситуацию, которая

неизбежно приведет ксерьезной травме или

смертельному исходу, вслучае несоблюдения

соответствующих мербезопасности.

ВНИМАНИЕ: Указывает на потенциально опасную

ситуацию, которая, вслучае несоблюдения

соответствующих мер безопасности,

может привести ксерьезной травме или

смертельномуисходу.

ПРЕДУПРЕЖДЕНИЕ: Указывает на потенциально

опасную ситуацию, которая, вслучае несоблюдения

соответствующих мер безопасности может

стать причиной травм средней или легкой

степенитяжести.

Эти продукты также соответствуют Директивам 2014/30/EU

и 2011/65/EU. Для получения дополнительной информации

обратитесь в компанию DEWALT по адресу, указанному ниже

или приведенному на задней стороне обложки руководства.

Нижеподписавшийся несет ответственность за составление

технической документации и составил данную декларацию

по поручению компанииDEWALT.

Маркус Ромпел

Вице‑президент по инженерным разработкам, PTE‑Europe

DEWALT, Richard‑Klinger‑Straße 11,

65510, Idstein, Germany

19.08.2020

**Код даты 201536или новее

Батареи Зарядные устройства/время зарядки (мин)

Кат. № Vпост. тока Ah Вес (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB116 DCB117 DCB118 DCB132 DCB119

DCB546 18/54 6,0/2,0 1,05 60 270 170 140 90 80 40 60 90 X

DCB547 18/54 9,0/3,0 1,46 75* 420 270 220 135* 110* 60 75* 135* X

DCB548 18/54 12,0/4,0 1,44 120 540 350 300 180 150 80 120 180 X

DCB181 18 1,5 0,35 22 70 45 35 22 22 22 22 22 45

DCB182 18 4,0 0,61 60/40** 185 120 100 60 60/45** 60/40** 60/40** 60 120

DCB183/B/G 18 2,0 0,40 30 90 60 50 30 30 30 30 30 60

DCB184/B/G 18 5,0 0,62 75/50** 240 150 120 75 75/60** 75/50** 75/50** 75 150

DCB185 18 1,3 0,35 22 60 40 30 22 22 22 22 22 40

DCB187 18 3,0 0,54 45 140 90 70 45 45 45 45 45 90

DCB189 18 4,0 0,54 60 185 120 100 60 60 60 60 60 120

*Код даты 201811475B или новее

**Код даты 201536 или новее

PУССКИЙ

обувь снескользящей подошвой, каска изащитные

наушники, используемые при работе, уменьшают

риск получениятравм.

c ) Примите меры для предотвращения

случайного включения. Перед тем как

подключить электроинструмент ксети и/или

аккумуляторной батарее, взять инструмент

или перенести его на другое место, убедитесь

втом, что выключатель находится

вположении «Выкл.». Если при переноске

электроинструмента он подключен ксети, ипри

этом ваш палец находится на выключателе, это

может стать причиной несчастныхслучаев.

d ) Уберите все регулировочные или гаечные ключи

перед включением электроинструмента.

Ключ, оставленный на вращающейся части

электроинструмента, может привести ктравме.

e ) Не пытайтесь дотянуться до слишком

удаленных поверхностей. Обувь должна быть

удобной, чтобы вы всегда могли сохранять

равновесие. Это позволит лучше контролировать

электроинструмент внепредвиденныхситуациях.

f ) Одевайтесь соответствующим образом.

Избегайте носить свободную одежду

иювелирные украшения. Следите за тем,

чтобы волосы иодежда не попадали под

движущиеся детали. Возможно наматывание

свободной одежды, ювелирных изделий идлинных

волос на движущиесядетали.

g ) При наличии устройств для подключения

оборудования для удаления исбора пыли

необходимо обеспечить правильность их

подключения иэксплуатации. Использование

устройства для пылеудаления сокращает риски,

связанные спылью.

h ) Не позволяйте хорошему знанию от частого

использования инструментов стать причиной

самонадеянности иигнорирования правил

техники безопасности. Небрежное действие

может повлечь серьезные травмы за долюсекунды.

4) Эксплуатация электроинструмента иуход

за ним

a ) Избегайте чрезмерной нагрузки

электроинструмента. Используйте

электроинструмент всоответствии

сназначением. Правильно подобранный

электроинструмент выполнит работу более

эффективно ибезопасно при стандартнойнагрузке.

b ) Не пользуйтесь инструментом, если

не работает выключатель. Любой

инструмент, управлять выключением

ивключением которого невозможно, опасен, иего

необходимоотремонтировать.

c ) Перед выполнением любых настроек,

сменой аксессуаров или прежде чем убрать

инструмент на хранение, отключите его от

сети и/или снимите снего аккумуляторную

c ) Следите за тем, чтобы во время работы

сэлектроинструментом взоне работы

не было посторонних идетей. Отвлекаясь

от работы вы можете потерять контроль

надинструментом.

2) Электробезопасность

a ) Штепсельная вилка электроинструмента

должна соответствовать розетке. Никогда

не меняйте вилку инструмента. Запрещается

использовать переходники квилкам для

электроинструментов сзаземлением.

Использование оригинальных штепсельных вилок,

соответствующих типу сетевой розетки снижает

риск поражения электрическимтоком.

b ) Избегайте контакта сзаземленными

поверхностями, такими как трубы,

радиаторы ихолодильники. Если вы будете

заземлены, увеличивается риск поражения

электрическимтоком.

c ) Запрещается оставлять электроинструмент

под дождем ивместах повышенной влажности.

При попадании воды вэлектроинструмент риск

поражения электротокомвозрастает.

d ) Берегите кабель от повреждений. Никогда

не используйте кабель для переноски

инструмента, не тяните за него, пытаясь

отключить инструмент от сети. Держите

кабель подальше от источников тепла, масла,

острых углов или движущихся предметов.

Поврежденный или запутанный кабель питания

повышает риск поражения электрическимтоком.

e ) При работе сэлектроинструментом на

открытом воздухе используйте удлинитель,

подходящий для использования на улице.

Использования кабеля питания, предназначенного

для использования вне помещения, снижает риск

поражения электрическимтоком.

f ) Если использование электроинструмента

вусловиях повышенной влажности неизбежно,

используйте устройства защитного

отключения (УЗО) для защиты сети.

Использование УЗО сокращает риск поражения

электрическимтоком.

3) Обеспечение индивидуальной

безопасности

a ) Будьте внимательны, смотрите, что делаете

ине забывайте оздравом смысле при работе

сэлектроинструментом. Запрещается

работать сэлектроинструментом

всостоянии усталости, наркотического,

алкогольного опьянения или под воздействием

лекарственных препаратов. Невнимательность

при работе сэлектроинструментом может

привести ксерьезным телеснымповреждениям.

b ) Используйте индивидуальные средства

защиты. Всегда используйте защитные очки.

Средства защиты, такие как пылезащитная маска,

PУССКИЙ

Дополнительные специальные правила

безопасности при использовании дрелей/

шуруповертов/ударных дрелей

• При эксплуатации ударных дрелей надевайте

защитные наушники. Шум может стать причиной

сниженияслуха.

• Пользуйтесь дополнительными рукоятками,

входящими в комплект поставки инструмента.

Потеря контроля может привести ктравме.

• Перед использованием правильно захватите

инструмент. Инструмент создает высокий крутящий

момент, что, в отсутствие должного крепления во

время работы, может привести к потере управления и

последующимтравмам.

• Удерживайте инструмент за изолированные

поверхности захватывания при выполнении

аккумуляторной батареи может привести кпожару

или получениюожогов.

d ) При повреждении батареи, из нее может

вытечь электролит. Не прикасайтесь кнему.

При случайном контакте сэлектролитом

смойте его водой. При попадании электролита

вглаза обратитесь за медицинской помощью.

Жидкость, находящаяся внутри батареи, может

вызвать раздражение илиожоги.

e ) Не используйте поврежденные или измененные

аккумуляторные батареи или инструменты.

Поврежденные или измененные аккумуляторные

батареи могут работать непредсказуемо, что

может привести квозгоранию, взрыву или риску

получениятравм.

f ) Не подвергайте аккумуляторные батареи

или инструмент воздействию огня или

повышенной температуры. Открытый огонь

или воздействие высокой температуры выше 130°C

может привести квзрыву.

g ) Следуйте всем инструкциям по зарядке ине

заряжайте аккумуляторную батарею или

инструмент вне температурного диапазона,

указанного винструкции. Неправильная зарядка

или зарядка вне указанного температурного

диапазона может привести кповреждению батареи

иувеличить риск возгорания.

6) Обслуживание

a ) Обслуживание электроинструмента

должен проводить квалифицированный

специалист сиспользованием только

оригинальных запасных частей. Это позволит

обеспечить безопасность обслуживаемого

электрифицированногоинструмента.

b ) Не выполняйте обслуживание поврежденных

аккумуляторных батарей. Обслуживание

аккумуляторных батарей должно выполняться

только производителем или авторизованными

поставщикамиуслуг.

батарею, если ее можно снять. Такие

превентивные меры безопасности сокращают риск

случайного включенияэлектроинструмента.

d ) Храните электроинструмент внедоступном

для детей месте ине позволяйте работать

синструментом людям, не имеющим

соответствующих навыков работы стакого

рода инструментами. Электроинструмент

представляет опасность вруках

неопытныхпользователей.

e ) Поддерживайте электроинструмент

ипринадлежности висправном состоянии.

Проверьте, не нарушена ли центровка или

не заклинены ли движущиеся детали, нет

ли повреждений или иных неисправностей,

которые могли бы повлиять на работу

электроинструмента. Вслучае обнаружения

повреждений, прежде чем приступить

кэксплуатации электроинструмента, его

нужно отремонтировать. Большинство

несчастных случаев происходит из‑за

электроинструментов, которые не обслуживаются

должнымобразом.

f ) Содержите режущий инструмент востро

заточенном ичистом состоянии. Вероятность

заклинивания инструмента, за которым следят

должным образом икоторый хорошо заточен,

значительно меньше, аработать снимлегче.

g ) Используйте электроинструменты,

принадлежности инасадки всоответствии

сданными инструкциями, принимая во

внимание условия работы ихарактер

выполняемой работы. Использование

электроинструмента для выполнения операций,

для которых он не предназначен, может привести

ксозданию опасныхситуаций.

h ) Все рукоятки иповерхности захватывания

должны быть сухими ибез следов смазки.

Скользкие рукоятки иповерхности захватывания

не позволяют обеспечить безопасность

работы иуправления инструментом

внепредвиденныхситуациях.

5) Использование аккумуляторных

электроинструментов иуход за ними

a ) Используйте для зарядки аккумуляторной

батареи только указанное производителем

зарядное устройство. Использование зарядного

устройства определенного типа для зарядки других

батарей может привести квозгоранию.

b ) Используйте для электроинструмента только

батареи указанного типа. Использование других

аккумуляторных батарей может стать причиной

травмы ипожара.

c ) Оберегайте батарею от попадания внее

скрепок, монет, ключей, гвоздей, болтов или

других мелких металлических предметов,

которые могут вызывать замыкание

контактов. Короткое замыкание контактов

PУССКИЙ

Зарядные устройства

Зарядные устройства DEWALT не требуют регулировки

имаксимально просты виспользовании.

Электробезопасность

Электродвигатель рассчитан на работу только при одном

напряжении сети. Необходимо обязательно убедиться

втом, что напряжение источника питания соответствует

указанному на шильдике устройства. Необходимо также

убедиться втом, что напряжение работы зарядного

устройства соответствует напряжению всети.

iЗарядное устройство DEWALT оснащено двойной

изоляцией всоответствии стребованиями

EN60335; поэтому провод заземления

нетребуется.

Вслучае повреждения кабеля питания его необходимо

заменить специально подготовленным кабелем, который

можно приобрести всервисных центрахDEWALT.

Использование удлинительного кабеля

Используйте удлинитель только вслучаях крайней

необходимости. Используйте только утвержденные

удлинители промышленного изготовления, рассчитанные

на мощность не меньшую, чем потребляемая мощность

зарядного устройства (см. Технические характеристики).

Минимальное поперечное сечение провода электрического

кабеля должно составлять 1мм2; максимальная длина 30м.

При использовании кабельного барабана всегда полностью

разматывайтекабель.

Важные инструкции по технике безопасности

для всех зарядных устройств

СОХРАНИТЕ НАСТОЯЩЕЕ РУКОВОДСТВО. Вданном

руководстве содержатся важные инструкции по технике

безопасности для совместимых зарядных устройств (см.

Техническиехарактеристики).

• Перед тем как использовать зарядное устройство,

внимательно изучите все инструкции

ипредупреждающие этикетки на зарядном

устройстве, батарее иинструменте, для которого

используетсябатарея.

ВНИМАНИЕ: Опасность поражения электрическим

током. Не допускайте попадания жидкости

взарядное устройство. Это может привести

кпоражению электрическимтоком.

ВНИМАНИЕ: Рекомендуется использовать

устройство защитного отключения (УЗО) стоком

утечки до 30мA.

ВНИМАНИЕ: Опасность ожога. Во избежание травм,

следует использовать только аккумуляторные

батареи производства DEWALT. Использование

• риск получения ожогов врезультате нагревания

инструмента впроцессе работы;

• риск получения травмы врезультате

продолжительнойработы.

СОХРАНИТЕ НАСТОЯЩЕЕ РУКОВОДСТВО

Остаточные риски

Несмотря на соблюдение соответствующих инструкций по

технике безопасности ииспользование предохранительных

устройств, некоторые остаточные риски невозможно

полностью исключить.А именно:

• ухудшение слуха;

• риск травм от разлетающихся частиц;

работ, во время которых имеется

вероятность контакта инструмента со

скрытой электропроводкой. При удерживании

металлических деталей инструмента или крепежных

принадлежностей, в случае перерезания находящегося

под напряжением провода возможно поражение

оператора электрическимтоком.

Правила техники безопасности при

использовании длинных насадок

• Не работайте со скоростью выше максимальной

рекомендуемой скорости насадки. На более высокой

скорости повышается вероятность искривления

насадки при свободном вращении без контакта с

заготовкой, что может повлечь за собойтравмы.

• Всегда начинайте сверлить на низкой скорости

и только при контакте насадки с заготовкой. На

более высокой скорости повышается вероятность

искривления насадки при свободном вращении без

контакта с заготовкой, что может повлечь за

собойтравмы.

• Прилагайте усилие только параллельно насадке

и не прилагайте чрезмерное усилие. Это может

погнуть насадку, что может привести к поломке

или потере управления, что может повлечь за

собойтравмы.

• Используйте зажимы или другие уместные

средства фиксации заготовки на устойчивой

опоре. Удерживание заготовки рукой или прижимание

ее к телу не обеспечивает устойчивости и может

привести к потереконтроля.

• Используйте защитные наушники в случае работы

с инструментом в течение длительного периода

времени. Длительное воздействие шума высокой

мощности может привести к нарушениям слуха.

Временная потеря слуха или серьезное повреждение

барабанной перепонки могут возникать из‑за высоких

уровней шума, вызванных сверлением сударом.

• Всегда надевайте защитные очки или другое

устройство защиты для глаз. Во время сверления без

удара или с ударом могут разлетаться кусочки стружки

и частицы материала. Разлетающиеся осколки могут

серьезно повредитьглаза.

• Долота и сверла в процессе работы сильно

нагреваются. Прикасайтесь к ним, предварительно

надевперчатки.

Страница загружается...

DeWalt DCD999 Руководство пользователя

Похожие модели бренда

Модели других брендов