Tripp Lite Owner's Manual Single-Phase Rack-Mount Online UPS Инструкция по применению

Product Bundle Conﬁgurations:

SU5KRT3UHVMB, SU5KRT3UGMB, SU5KRT3UHWMB, SU6KRT3UHVMB,

SU6KRT3UGMB, SU6KRT3UHWMB, SU6KRT3UXMB

Models:

SUPDMB5, SUPDMB6, SUPDMB6IEC, SUPDMB5G, SUPDMB6G, SUPDMB5HW, SUPDMB6HW

(Series Number: AG-03DD)

SU5KRT3PM, SU6KRT3PM

(Series Number: AG-0357)

1

Owner’s Manual

SmartOnline

®

Single-Phase Rack-Mount Online UPS

with Built-in LCD Monitoring, Control Screen and

Detachable Bypass Power Distribution Module

Not suitable for mobile applications.

NOTE: External battery pack options require conﬁguration using front panel LCD interface or via Tripp Lite’s EXTERNAL BATTERY CONFIGURATION software.

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

®

is a trademark of Tripp Lite. For latest updates, please visit tripplite.com

WARRANTY REGISTRATION

Register your product today and be

automatically entered to win an ISOBAR

®

surge protector in our monthly drawing!

tripplite.com/warranty

Español 41 • Français 81 • Русский 121

2

Table of Contents

1. Overview 3

Parts List 3

Additional Accessory Options 3

2. Important Safety Instructions 3

3. UPS Circuit Block Diagram 6

4. Installation 7

Internal Battery Rotation 7

Rack Mounting 9

Tower Mounting 14

Hardwire Input and Output Wiring Instructions 15

(Optional with Select Models)

UPS Input and Output Overview 16

5. Features 17

Front Panel Controls, LEDs and LCD Screen 17

UPS Rear Panel 17

PDM Panel 18

6. Operations 19

LCD Front Panel Display and Controls 19

LED Front Panel Indicators 20

Front Panel Button Functions 21

Home Screen Layout 21

Basic Connections and Start-Up 22

Power Strategy Selection Options 25

Front Panel LCD Selection and 27

Configuration Options

Configuring External Battery Packs 30

PDM Maintenance Bypass Procedure 31

Replacement UPS Power Module 31

Installation Procedure

7. Optional Connections 32

8. Troubleshooting and Event Log 35

9. Internal Battery Replacement 37

10. Fan Replacement 39

11. Storage and Service 40

12. Product Registration 40

3

Overview

Tripp Lite SmartOnline rack-mount UPS systems with interactive LCD interface feature on-line, double-conversion UPS protection with full-

time sinewave output and zero transfer time, making them suitable for all advanced networking applications. The detachable Power

Distribution Module (PDM) uses a blindmate connection, providing a seamless installation and allowing the UPS to be serviced or hot-

swapped while keeping connected loads powered. Each UPS provides long running battery support with optional extended-run and Web

communications ability. Built-in interfaces include Micro-USB, RS-232 serial, Emergency Power Off (EPO), Remote On/Off (ROO) and an

RJ-11 smart battery port. The interactive front panel LCD screen provides detailed UPS status, preset and control options. Optional max

efficiency and auto-adaptive power strategy options enable high-efficiency operation with reduced power consumption and BTU heat output.

Parts List

UPS System UPS 4-Post Rail Kit Tower Mounting Plate (2) Bypass PDM (Outlets and Outlet

Configuration Vary by Model)

PDM Mounting

Brackets

Deep Rack Extension

Bracket (2)

M4 x 6 mm

Screw (8)

Thumbscrew (4) Bolt-on Mounting

Ears (2)

Hardwire Strain

Reliefs (2)

Optional Accessories (Not Included)

• 2POSTRMKITWM: Supports rack-mount UPS and battery packs in 2-post rack-mount or wall-mount configurations

• 2-9USTAND: Supports rack-mount UPS and battery packs in upright tower configuration

• BP192V12RT3US External “SMART” Battery Pack: Extends the runtime of the UPS system

USB Cable (1) RS-232 Cable (1) (Select models) AC Input Power

Cord with L6-30P Plug (1)

Owner’s Manual

4

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important instructions and warnings that should be followed during the installation, operation, maintenance and

storage of all Tripp Lite UPS Systems, Batteries and Detachable PDM. Failure to heed these warnings may affect your warranty.

Explanation of Symbols

Caution—risk of danger

Hot—overheating may occur

Electrical shock hazard

Protective earth ground

Bonding ground

Recyclable—contains lead

UPS Location Warnings

• Your UPS/PDM is intended to be used in a temperature-regulated, indoor area that is relatively free of conductive contaminants. Install

your UPS/PDM indoors, away from excess moisture or heat, conductive contaminants, dust or direct sunlight.

• Ambient room temperature should be between 32°F and 104°F (0°C and 40°C).

• Leave adequate space around all sides of the UPS for proper ventilation.

• The PDM provides the convenience of multiple outlets, but DOES NOT provide surge or line noise protection for connected equipment,

when in Bypass Mode.

• Do not mount unit with its front or rear panel blocked. Mounting in this manner will seriously inhibit the unit’s internal cooling, eventually

causing product damage not covered under warranty.

UPS Installation and Connection Warnings

All Models

CAUTION: Installation should be performed by qualified professional electrical service personnel only.

• Install in accordance with National Electrical Code standards. Be sure to use the proper overcurrent protection for the installation in

accordance with the plug/equipment rating.

• Be sure to use an upstream circuit breaker with a C curve.

• Overcurrent protection shall be provided in the end-use application, installed in accordance with local and national electrical wiring

regulations.

• Short-circuit backup protection and overcurrent protection is provided by the building Installation, in the hardwire configuration (Bypass

and Economy Modes).

• Install at a height not exceeding 1 m (3.3 ft.).

• Equipment is intended for use on a TN-S power distribution system.

Select Models Equipped with an L6-30P Plug

CAUTION: To reduce the risk of fire, connect only to a circuit provided with 30A maximum branch circuit overcurrent protection in

accordance with the National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code, Part I, C22.1.

• The AC mains L6-30P plug serves as the disconnect device. The electrical outlets supplying power to the equipment must be installed

near the equipment and easily accessible. Alternatively, a local disconnect may be provided.

•

DO NOT use the hardwire AC supply input option when an L6-30P plug is present. Doing so may cause a catastrophic dangerous situation.

• When the hardwire AC output is used, appropriate output overcurrent protection must be provided.

5

Select Hardwire Models

CAUTION: To reduce the risk of fire, connect only to a circuit provided with maximum branch circuit overcurrent protection in

accordance with the National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code, Part I, C22.1. See “UPS Input and

Output Overview” table in the Installation section for details.

• Use copper conductors with rated 105°C wires only. See “UPS Input and Output Overview” table in the Installation section for

recommended input and output configuration.

• For models equipped with a permanent hardwire output connection, overcurrent protection is to be provided in the end use installation.

Use output branch-rated overcurrent protection not exceeding the UPS Output rating. When supplying receptacles with lesser branch-

rated overcurrent protection, the overcurrent protection should match the receptacle rating.

• In Europe, the circuit breaker must meet the IEC/ EN 60934 standard and have a contact air gap of at least 3 mm.

• When the hardwire AC output is used, appropriate OUTPUT OVERCURRENT protection must be provided by the installer. Be sure to use

branch rated circuit breakers that match the rating of the receptacles/equipment being protected. Use circuit breaker(s) with a C curve.

• An appropriate and readily accessible two-pole disconnect device must be incorporated in the fixed wiring.

• In Europe, the AC mains connection is L, N, PE(GND). Make sure to hook up the L to the hot and N to the neutral conductor.

• Never attempt to install electrical equipment during a thunderstorm.

• Do not attempt to use this equipment if any part of it becomes damaged.

• Individual equipment connected to the UPS/PDM should not draw more current than the PDM outlet’s rating.

• The total load connected to the UPS/PDM must not exceed the maximum load rating for the UPS/PDM.

• Do not attempt to modify the UPS/PDM, enclosure, input plugs or power cables.

• Do not attempt to use the UPS/PDM if any part of it becomes damaged.

Equipment Connection Warnings

• Do not connect surge protectors or extension cords to the output of your UPS. This may damage the UPS and may affect the surge

protector and UPS warranties.

• The total load connected to the UPS must not exceed the maximum nameplate load rating.

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the

life support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment within oxygen-

enriched atmospheres, or within 0.3 m (1 ft.) of a point at which an oxygen-enriched atmosphere is intentionally vented

Fan Replacement Warning

Make sure UPS is powered down, i.e. turned off prior to fan replacement. Failure to do so may cause overheating and

trigger thermal shutdown

CAUTION: The fan circuitry is not isolated from AC mains. Turn off power to the UPS prior to fan replacement. Fan

replacement must be performed by qualified electrical service personnel.

Battery Warnings

• There are no user-serviceable parts inside the UPS.

• Battery rotation must be performed by qualified electrical service personnel.

• Battery replacement should be performed only by authorized service personnel.

• Servicing of batteries should be performed or supervised by personnel knowledgeable about batteries and the required precautions.

• When replacing batteries, replace with the same type and number of batteries or battery packs.

CAUTION: Do not dispose of batteries in a fire. The batteries may explode.

CAUTION: Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may be toxic.

CAUTION: A battery can present a risk of electrical shock and high short-circuit current. Contact with any part of a grounded battery can

result in electrical shock. The following precautions should be observed when working on batteries:

• Remove watches, rings, or other metal objects.

• Use tools with insulated handles.

• Wear rubber gloves and boots.

• Do not lay tools or metal parts on top of batteries.

Important Safety Instructions

6

Important Safety Instructions

• Do not short or bridge the battery terminals with any object.

• Remove battery grounds during installation and maintenance to reduce likelihood of shock.

• Remove the connection from ground if any part of the battery is determined to be grounded.

External Battery Warnings

• Connect external battery ground wire before connecting external battery to UPS.

• For external battery configuration, see the Operations section for options and configuration method. Smart battery packs are

automatically detected by the UPS.

• Fuses should be replaced only by factory authorized personnel. Replacement fuses should be of the same rating and type.

• For extended runtime, only use compatible Tripp Lite battery modules:

• BP192V12RT3US External Battery Pack

Battery Replacement and Recycling

Tripp Lite products use sealed lead-acid batteries, which are highly recyclable. Refer to your local codes for disposal requirements,

Call Tripp Lite at +1.773.869.1234 or visit tripplite.com/support/recycling-program for more information on recycling the batteries

or any other Tripp Lite product.

Tripp Lite offers a complete line of UPS System Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite on the Web at

tripplite.com/products/battery-finder/ to locate the specific replacement battery for your UPS.

Maintenance Warnings

• Your UPS does not contain user-serviceable parts. Do not disassemble.

UPS Circuit Block Diagram

Bypass

Battery

BUS Inverter Relay

Charger

Rectiﬁer

& Booster

L1 L1

EMI Relay EMI

L2/N

7

Installation

Internal Battery Rotation

Your UPS ships with the batteries disconnected and in reverse orientation. Before mounting the UPS to your 4-post or 2-post rack, first

remove the battery trays and set them aside. To remove the batteries from the UPS, follow the instructions below.

If an external battery pack is to be used, it should be installed first in the lower part of the rack. Be sure to follow

instructions for Configuring External Battery Packs in this manual and in the BP192V12RT3US Owner’s Manual

before proceeding with UPS installation.

WARNING! Battery rotation must be performed by qualified electrical service personnel.

1

2

3

4

1

Remove the six front screws from the front bezel, then retract

the bezel from the UPS. Hang the bezel on the available hook.

Note: The front panel display has an attached ribbon cable that

extends from the UPS to the front bezel. Make sure to keep this cable

out of the way when opening and closing the battery door.

2

Loosen the two captive screws securing the battery door.

3

Open the battery door. Ensure the smart battery

communications cable is safely out of the way when opening

the battery door and when removing the battery trays.

4

Using the handles attached to each tray, remove the battery

pack trays. Make sure to remove the handles before rotating the

batteries (see next step) and install the handles on the opposite

side.

It is recommended you remove the UPS internal batteries prior

to installation. Doing so will remove excess weight and allow for

safer handling.

Note: To reduce the weight of the UPS unit during installation, it is

recommended you proceed to 4-Post Mounting or 2-Post Mounting

instructions in the Rack Mounting section before rotating, reinstalling

and connecting the battery pack trays.

8

Installation

1

2

5

7

6

8

5

Each battery tray uses a blindmate DC connector. Position each

battery tray so the red and black DC connector end is facing

towards the rear of the UPS and the communication port is

facing toward the front of the UPS. Starting with the right side

battery tray, insert the battery tray, making sure it protrudes

slightly from the UPS. Repeat for the left side battery tray.

Note: For better connector access, attach the cables before the battery

packs are fully inserted into the UPS.

6

Connect the battery communication cable to each battery tray

and push the battery trays completely into the UPS.

7

Close the battery door and secure by tightening the captive

screws.

8

Reattach the front bezel to the UPS and secure with the screws

removed in step

1

.

9

Installation

Rack Mounting

Mount your equipment in either a 4-post or 2-post rack or rack enclosure. The user must determine the fitness of hardware and

procedures before mounting. If hardware and procedures are not suitable for your application, contact the manufacturer of your rack or

rack enclosure. The procedures described in this manual are for common rack and rack enclosure types and may not be appropriate for all

applications.

CAUTION: The equipment should be installed onto the rack rails at a height <1 m (36 in.).

If an external battery pack is to be used, it should be installed first in the lower part of the rack. Be sure to follow

instructions for Configuring External Battery Packs in this manual and in the BP192V12RT3US Owner’s Manual

before proceeding with UPS installation.

4-Post Mounting

Mounting the UPS

1

The included plastic pegs

A

will temporarily support the empty

rack-mount shelves

B

while you install the permanent mounting

hardware. Insert a peg into the third hole from the top on the

front end of each bracket. On the rear end, insert a peg into the

center hole. (Each front bracket has 6 holes and each rear

bracket has 5 holes.) The pegs will snap into place.

After installing the pegs, expand each shelf to match the depth

of your rack rails. The pegs will fit through the square holes in

the rack rails to support the shelves. Refer to the rack unit

labels to confirm that the shelves are level in all directions.

Note: The support ledge of each shelf must face inward.

2

Remove the pegs at the front end of each bracket. Secure the

shelves

B

to the mounting rails permanently using the included

screws and cup washers

C

as shown. Place 2 screws at the

front of each rail (4 total) and 2 screws at the back of each rail

(4 total). When securing to the rear rail, make sure each

set of bracket screws are positioned above and below the

lower screw used to secure the PDM Mounting Bracket

D

.

Tighten all screws before proceeding.

Note: The rear pegs can be left in for installation, but the front ones

must be removed before the bracket is secured by screws.

WARNING!

Do not attempt to install your UPS until you have

inserted and tightened the required screws. The plastic

pegs will not support the weight of your UPS.

1

2

A

B

C

10

Installation

4

With the aid of an assistant, lift your UPS and slide it into the shelves. Attach the UPS mounting ears to the front mounting rails with

user-supplied screws and washers

G

. Tighten all screws securely.

Note: To install battery trays inside the UPS, refer to instructions 5-8 in the Internal Battery Rotation section within the Installation section of this

manual.

4

G

PDM Outlet Configuration will Vary by Model

3

Attach your UPS mounting brackets

D

to the forward mounting

holes

E

of the UPS using the included hardware

F

. The

mounting bracket “ears” should face forward.

It is recommended you remove the UPS internal batteries prior

to installation. Doing so will remove excess weight and allow for

safer handling.

Note: To remove battery pack trays inside the UPS, refer to Internal

Battery Rotation.

3

D

E

F

1

2

11

Installation

Mounting the Power Distribution Module in Standard-Depth Rack Enclosures

PDM Outlet Configuration will Vary by Model

1

Using the thumbscrews, attach the PDM Mounting Brackets to

the PDM. The default position to install the thumbscrews is in

the center holes, as shown.

Notes:

• Do not fully tighten thumbscrews at this time.

• For extended runtime applications, attach and secure the external

battery cable and ground wire to the underside of the Bypass Power

Distribution Module battery connector and grounding screw.

2

Attach the PDM assembly to the rack’s rear rails. The brackets’ built-in hooks provide temporary support while securing the PDM to the

rack with the permanent mounting hardware.

Note: PDM Mounting Brackets can be laterally adjusted to ensure a proper connection between the UPS and PDM. To adjust the brackets, loosen the

thumbscrews. Fully extend the PDM to the end of the brackets. Do not tighten screws at this time. Refer to step 4 for more information.

Bypass Power Distribution Module Attachment Points – The

tightening torque for the ground screw is 1 n•m (10 lb•in.).

Ground

Terminal

Battery

Connector

3

12

Installation

PDM Outlet Configuration will Vary by Model

3

Push the PDM toward the UPS so its blindmate connectors securely mate with the connectors on the UPS

A

. A green pin will appear

on the PDM’s front panel to indicate a proper connection

B

. Once the PDM and UPS are properly mated, tighten the thumb screws

C

.

A

B

C

A

B

C

Mounting the Power Distribution Module in Extra-Deep Rack Enclosures

1

Use the included M4 x 6 mm Phillips Screws to attach the Deep

Rack Extension Brackets to the PDM.

1

PDM Outlet Configuration will Vary by Model

13

Installation

2-Post Mounting

If you mount 2U UPS models in 2-post racks, they require the addition of a Tripp Lite 2-Post Rack-Mount Installation Kit (model:

2POSTRMKITMB, sold separately). See Installation Kit owner’s manual for installation procedure.

2

PDM Outlet Configuration will Vary by Model

2

Using the thumbscrews, attach the PDM Mounting Brackets to

the Deep Rack Extension Brackets.

To attach the PDM assembly to a 4-post rack,

refer to Mounting the Power Distribution Module in

Standard-Depth Rack Enclosures, instructions

2

and

3

.

14

Installation

Tower Mounting

WARNING!

All UPS systems are extremely heavy. Use caution when lifting and mounting. User must properly stabilize the UPS

when lifting and mounting.

Your UPS can be mounted in an upright tower position with optional base stands sold separately by Tripp Lite (model: 2-9USTAND). When

mounting the UPS on adjustable base stands, make sure the LCD panel is facing toward the top.

The LCD panel may be rotated for easier viewing while the UPS is upright. To rotate, insert a small screwdriver or other flat-edge tool into

the slots on any side of the LCD panel. Pop the panel out, rotate accordingly and snap it back into place.

WARNING: Display circuitry is not isolated. Display rotation must be performed only by qualified electrical service

personnel.

EXTERNAL BATTERY CONFIGURATION NOTE

If external battery packs are to be used with this UPS, install them following the mounting/installation documentation included with each

battery pack.

These SmartOnline UPS systems support automatic detection of up to four compatible Tripp Lite Smart battery packs. Each Smart battery

pack includes a wired data connection that enables automatic detection and configuration for up to four Smart external battery packs to

the UPS. If more than four external battery packs need to be configured, all packs must be configured via the Tripp Lite external battery

configuration software connecting though the UPS serial port. In this configuration, do not connect the Smart battery communication cables

to any of the external battery packs.

To attach the PDM unit, use the included screws to attach the Tower Mounting Plate to the UPS

A

. Align and mate the PDM’s blindmate

connectors with the connectors on the UPS

B

. A green pin will appear on the PDM’s front panel to indicate a proper connection

C

. Use

the thumbscrews to secure both sides of the PDM unit to the UPS via the Tower Mounting Plates

D

.

A

B

D

C

PDM Outlet Configuration

will Vary by Model

PDM Outlet Configuration will Vary by Model

15

Installation

Input and Output Wiring Instructions (Optional with Select Models)

Note: The tightening torque is 1 n•m (10 lb•in.).

CAUTION: This type of connection must be performed by qualified professional electrical service personnel only. When making connections,

check that the mains power to the UPS is OFF. Connect the ground wires from the cables to the chassis ground lug. Always connect the

ground wire first.

Be sure to observe the Input Line Configuration, Breaker and wire AWG as outlined in the UPS Input and Output Overview table, detailed

in this section.

Note: Select models include an AC input cord with L6-30P plug. If this AC cord is to be used, the UPS input/output power capacity ratings will change. See

the UPS nameplate for more information.

1

Detach the PDM from the UPS.

Hardwire Input/Output models: Before removing the terminal

block cover ensure that flexible conduits used for hardwire input

and output are the correct length to reach the fixed knockout

locations on PDM. Remove the appropriate knockout sized for

your conduit from both Hardwire Input and Hardwire Output

locations on the PDM terminal block cover.

Corded Models: Remove the knockout from the Hardwire Input

location on the terminal block cover.

Note: If you will use hardwire output in combination with UPS models

with outlets, remove the appropriate hardwire output knockout at this

time.

2

Unscrew the four screws to remove the terminal strip cover and

slide out.

3

Hardwire Models: Insert and secure the included user-supplied

strain reliefs or connectors and secure to terminal block cover.

Corded Models: Attach and secure one of the included strain

reliefs to the hardwire input side of terminal cover. Pass the

included hardwire side of the cord with L6-30P plug. Do not

tighten outer part of strain relief at this time.

4

Hardwire Models: Connect the two sets of L1, L2/N and

Ground wires (1 Input, 1 Output) according to markings on the

terminal block. Be sure to connect one set of wires to the input

terminals and the other set to the output terminals.

Corded Models: Pass input cord through strain relief. Connect

and secure the input cord wire connections to the L1 In, L2/N In

and input ground hardwire terminals. Tighten the outer strain

relief.

Note: If hardwired output is used in combination with models that have

outlets, connect the device wiring to the L1 Out, L2/N Out and output

ground hardwire terminals at this time.

5

Slide in and reattach the terminal strip cover with the four

screws removed in step 2.

2

5

3

PDM Outlets and

Outlet Configuration

will Vary by Model

PDM Outlets and

Outlet Configuration

will Vary by Model

Hardwire Input

L1 In L1 OutL2/N In L2/N OutGround Ground

Hardwire Output

16

Installation

UPS Input and Output Overview

Model Name

Input

Connection

Input Line

Conﬁguration

Building Breaker

C-Curve Input AWG (mm

2

)

Receptacle Plate

Conﬁguration

SUPDMB5 HW L1, L2/N, PE(GND) 40 8 (6)

L6-30P L1, L2/N, PE(GND) 30 10 (4)

SUPDMB5G HW L1, L2/N, PE(GND) 40 8 (6)

SUPDMB5HW HW L1, L2/N, PE(GND) 40 8 (6) None

SUPDMB6 HW L1, L2/N, PE(GND) 50 6 (10)

L6-30P L1, L2/N, PE(GND) 30 10 (4)

SUPDMB6IEC HW L, N, PE 50 6 (10)

SUPDMB6G HW L1, L2/N, PE(GND) 50 6 (10)

SUPDMB6HW HW L1, L2/N, PE(GND) 50 6 (10) None

210

3000

1 2 3

8

4

6

7

5

1

Accessory Slot: Remove the small cover panel from this slot to use optional accessories to remotely monitor and control your UPS.

Visit tripplite.com to see a full list of accessories, including a wide variety of network management and connectivity products.

2

Remote On/Off: The UPS supports connection of a remote On/Off switch. This port may be used to connect the UPS to a contact

closure switch to turn off the UPS system remotely. Make sure to use the terminal block on the left side labeled for remote On/Off

connection. See Optional Connections section for details.

3

EPO (Emergency Power Off) Port: Your UPS features a port that may be used to connect the UPS to a contact closure switch to

enable emergency shutdown of your UPS. Make sure to use the pins on the right terminal block labeled for EPO. See Optional

Connections section for details.

4

Communications Ports: These ports (USB or RS-232) connect your UPS to any workstation or server. Use with Tripp Lite’s PowerAlert

Software and included cable to enable your computer to automatically save open files and shut down equipment during a blackout. Also

use PowerAlert Software to monitor a wide variety of AC line power and UPS operating conditions. Consult your PowerAlert Software

manual or contact Tripp Lite Customer Support for more information. The 9-pin RS-232 port also supports dry-contact communications.

See USB & RS-232 Dry Contact Communications in the Optional Connections section for installation instructions.

5

External Battery Pack Detection Port: For external batteries with communication built-in, plugging the battery communication cable

into this port will allow the UPS to automatically detect smart battery packs. See the Configuring External Battery Packs in the

Operations section for configuration instructions.

6

Chassis Ground Screw: Use this to connect any equipment that requires a chassis ground.

7

Parallel Port: Reserved for future use.

8

Blindmate Power Connection Box: Connects the UPS to the detachable PDM (see PDM Panel for details by model).

17

Features

Before installing and operating your UPS, familiarize yourself with the locations and function of the features of each component.

UPS Rear Panel

Front Panel Controls, LEDs and LCD Screen

The graphical LCD on the front panel contains a wide range of UPS

operating conditions and diagnostic data. It also displays UPS

settings and options when viewing the UPS setup screens. The five

buttons below the LCD can be used to navigate the various

information, configuration and UPS control screens by following the

on-screen prompts and selection options. Additional LED indicators

above the LCD screen also provide at-a-glance status of AC input

source, availability of output, battery status, and warning/fault

status.

See Operations section for detailed descriptions of LCD functions,

buttons and LEDs.

18

Features

PDM Panel

SUPDMB5 SUPDMB5G

SUPDMB6 SUPDMB6IEC

SUPDMB6G ALL MODELS: Bottom view

A A A

A

A C

B

B B

B

C

Load Bank Receptacles Breaker

A

2x L6-30R 1x 2-Pole (30A)

B

2x L6-20R 1x 2-Pole (20A)

Load Bank Receptacles Breaker

A

*

2x C19 1x 1-Pole (16A)

B

2x C19 1x 1-Pole (16A)

C

4x C13 1x 1-Pole (10A)

Load Bank Receptacles Breaker

A

2x L6-30R 1x 2-Pole (30A)

B

2x L6-20R 1x 2-Pole (20A)

C

2x L6-20R 1x 2-Pole (20A)

Load Bank Receptacles Breaker

A

2x C19 1x 2-Pole (16A)

B

2x C19 1x 2-Pole (16A)

C

4x C13 1x 2-Pole (10A)

Load Bank Receptacles Breaker

A

2x C19 1x 1-Pole (16A)

B

2x C19 1x 1-Pole (16A)

C

6x C13 1x 1-Pole (10A)

9

13

14 16

16

14

1415

15

14

13

10 12

12

12 17

17

12

11

1110

10

9

9 9

9

*Uncontrolled Load Bank

16

15

9

Bypass Switch Cover: Prevents the Maintenance Bypass Switch from being set to BYPASS before putting the UPS in Electronic Bypass

mode.

10

Maintenance Bypass Switch: Allows qualified service personnel to remove the UPS for routine maintenance without disrupting power

to connected loads. While this switch is set to BYPASS, connected equipment will receive filtered AC mains power, but the equipment

will not receive battery power in the event of a blackout. See PDM Maintenance Bypass Procedure section for more information.

11

UPS Bypass Disabled LED (red): When attempting to enter Maintenance Bypass Mode via the Maintenance Bypass Switch, if this

LED is illuminated, the UPS is not in a valid state to switch the Maintenance Bypass Switch to the “BYP” position. Doing so would result

in the load being dropped.

When attempting to exit Maintenance Bypass Mode via the Maintenance Bypass Switch, if this LED is illuminated, the UPS is not in a

valid state to switch the Mainenance Bypass Switch to the “NORM” position. Doing so would result in the load being dropped.

12

UPS/PDM Mating Pin: Indicates a proper connection between the PDM’s blindmate connectors and the connectors on the UPS.

13

AC Input Connection: Connects to AC power via an attached power cord or hardwire connection.

Note: SUPDMB5G and SUPDMB6 models include an optional input cord.

14

AC Output Connection (optional on select models): Connects to an AC load via hardwire connection (See Hardwire Input and

Output Wiring Instructions for more information.

Note: The total load connected to the UPS must not exceed the maximum nameplate load rating.

15

External Battery Pack Connector (located on the PDM’s bottom panel): Your UPS features a robust internal battery system. Adding

external batteries will increase runtime and recharge time. See Additional Accessories (Optional) in the Overview section for

compatible models and Configuring External Battery Packs section under Operations section for configuration instructions.

Note: Do not connect or disconnect battery packs when the UPS is running on battery power.

16

DC Ground Screw: Use this to create a ground connection between the UPS and an attached external battery pack.

17

AC Receptacles (varies by model): These output receptacles provide connected equipment with pure sine-wave AC output during

normal operation and battery power during blackouts and severe brownouts. The receptacles are divided into load banks, as described

on the unit. Using PowerAlert software and cabling, load banks may be individually turned off and on from a remote location, allowing

users to reset or reboot connected equipment.

210

3000

LCD Screen

Escape

AC Input LED (Green)

Page Up/Page Down

Fault LED (Red)

On/Off

AC Output LED (Green) Battery Mode LED (Yellow)

Enter

19

Features

This section explains how to use your Tripp Lite Online UPS System, including front-panel LCD operation, operating modes, UPS startup and

shutdown, transferring between modes, setting power strategy, and configuring bypass settings, load segments and battery settings.

LCD Front Panel Display and Controls

A 5-button graphical LCD screen with additional LED indicators on the front of the UPS that provides information on UPS status, load level

information, event information, measurements, settings and a wide variety of UPS configuration and power strategy options.

Operations

210

3000

210

3000

210

3000

210

3000

20

Operations

LED Front Panel Indicators

There are 4 LEDs above the front panel LCD screen that offer information on AC INPUT, BYPASS, AC OUTPUT, BATTERY MODE and UPS

FAULT status.

AC INPUT indicator

On AC input is available AND AC input is WITHIN the configured ECONOMY / BYPASS mode range.

When this LED is ON SOLID, AC input is of adequate quality for UPS operation in BYPASS or ECONOMY MODE.

Flashing AC input is available AND AC input is OUTSIDE the configured BYPASS mode range.

When this LED is ON FLASHING, AC input is not of adequate voltage or frequency for UPS operation in BYPASS or

ECONOMY MODE.

Off AC input is NOT available.

When this LED is OFF, AC input is not available.

AC OUTPUT indicator

On UPS AC output is ON

UPS output is available at the UPS output receptacles.

Off UPS AC output is OFF

UPS AC output is not available.

BATTERY MODE indicator

On UPS is running in battery mode

UPS batteries are discharging as the UPS runs in battery mode. Also lights momentarily during self-test operation.

Flashing UPS is running in battery mode - Low battery warning

UPS batteries are discharging as the UPS runs in BATTERY mode and are becoming low. The indicator will flash at

2-second intervals to report LOW BATTERY and 0.5-second intervals to report BATTERIES ARE NEAR FULLY

DISCHARGED and the UPS is near shutdown.

UPS FAULT indicator

On UPS is experiencing a pre-defined fault state

See front panel display for explanation of error state or code information. See on-screen instructions and manual

for troubleshooting tips.

Off Normal

UPS is not reporting fault conditions when this indicator is OFF.

Страница загружается...

Tripp Lite Owner's Manual Single-Phase Rack-Mount Online UPS Инструкция по применению

Похожие модели бренда

Модели других брендов