ABB ACS850 series Quick Start Up Manual

ACS850

Quick Start-up Guide

Standard Control Program

English . . . . . . . . . . . . . . . 3

Dansk . . . . . . . . . . . . . . . 17

Deutsch. . . . . . . . . . . . . . 31

Español. . . . . . . . . . . . . . 47

Français . . . . . . . . . . . . . 61

Italiano . . . . . . . . . . . . . . 77

Nederlands . . . . . . . . . . . 91

Português (Brasil). . . . . 107

Suomi . . . . . . . . . . . . . . 121

Svenska . . . . . . . . . . . . 135

Türkçe. . . . . . . . . . . . . . 149

Русский . . . . . . . . . . . . 163

中文. . . . . . . . . . . . . . . . 181

3AUA0000045498 Rev D

Effective: 2012-08-06

 2012 ABB Oy.

ACS850 drive manuals

*The delivery includes a multilingual quick installation guide.

DRIVE HARDWARE MANUAL*

ACS850-04 Drive Modules (0.37 to 45 kW) Hardware Manual – 3AUA0000045496 (English)

ACS850-04 Drive Modules (55 to 160 kW, 75 to 200 hp) Hardware Manual – 3AUA0000045487

(English)

ACS850-04 Drive Modules (200 to 500 kW, 250 to 600 hp) Hardware Manual – 3AUA0000026234

(English)

ACS850-04 Drive Modules (400 to 560 kW, 450 to 700 hp) Hardware Manual – 3AUA0000081249

(English)

DRIVE FIRMWARE MANUALS

ACS850 Standard Control Program Firmware Manual – 3AUA0000045497 (English).

OPTION MANUALS

Manuals for I/O Extension Modules, Fieldbus Adapters, etc.*

APPLICATION GUIDES

Application programming for ACS850 drives – 3AUA0000078664 (English)

ATEX certified safe disconnection function for ACS850 drives – 3AUA0000074343 (English)

Common DC configuration application guide – 3AUA0000073108 (English)

Safe torque off function for ACSM1, ACS850 and ACQ810 drives – 3AFE68929814 (English)

Quick Start-up Guide for ACS850 with Standard Control Program 3

Quick Start-up Guide for ACS850 with Standard

Control Program

About this guide

This guide contains the basic procedure that needs to be followed to start up an

ACS850 drive (with Standard Control Program). During the procedure, the drive is set

up using the ACS850 Control Panel.

Note: Only the functions of the Control Panel needed during the procedure are

described in the guide. The complete instructions for using the Control Panel are

included in the ACS850 Standard Control Program Firmware Manual

(3AUA0000045497 [English]).

Safety instructions

WARNING! All electrical installation and maintenance work on the drive

should be carried out by qualified electricians only.

Never work on the drive, the braking chopper circuit, the motor cable or the motor

when input power is applied to the drive. Always ensure by measuring that no voltage

is actually present.

4 Quick Start-up Guide for ACS850 with Standard Control Program

Start-up procedure

Safety

The start-up may only be carried out by a qualified electrician.

The safety instructions must be followed during the start-up procedure. See the

safety instructions on the first pages of the appropriate hardware manual.

Check the installation. See the installation checklist in the appropriate hardware

manual.

Check that the starting of the motor does not cause any danger.

De-couple the driven machine if

• there is a risk of damage in case of an incorrect direction of rotation, or

• a normal ID run is required during the drive start-up, when the load torque is higher

than 20% or the machinery is not able to withstand the nominal torque transient

during the ID run.

Power-up, control panel basics

Connect the control panel to the drive using an

appropriate Category 5E cable.

Power up the drive. After a few moments, the panel

shows the Output mode (right).

Note: The Output mode display will alternate with

“Alarm 2021 NO MOTOR DATA” until motor data is

entered later in this procedure.

Switch to local control to ensure that external control

is disabled by pressing the key on the control

panel. Local control is indicated by the text “LOC” on

the top row on the display.

The two boxes on the bottom row of the display

indicate the function of the two soft keys and

. The contents of the boxes depend on the

visible menu choices.

Press (MENU) to access the Main menu.

Within any menu, the desired selection is

highlighted. Press the and keys to

make a new choice; activate by pressing

(ENTER).

The Main menu is the starting point for the

procedures described below.

Adjusting parameter values

Notes:

• At any point, press (CANCEL or EXIT) to return to the previous level.

• By default, not all parameters are visible. Set parameter 16.15 Menu set sel to Load

long to make all parameters visible.

00 A

00 Hz

0 %0.

0.

REM

DIR

MENU

0.00rpm

LOC

REM

00 A

00 Hz

0 %0.

0.

LOC

DIR

MENU

0.00rpm

PARAMETERS

ASSISTANTS

CHANGED PAR

EXIT ENTER

MAIN MENU 1

LOC

Quick Start-up Guide for ACS850 with Standard Control Program 5

To adjust a parameter within an assistant:

• Use the and keys to adjust the setting. Press SAVE to accept the

setting shown and to proceed to the next parameter.

To adjust a parameter at any other time:

• In the Main menu, highlight PARAMETERS and press (ENTER).

• Use and to browse the list of parameter groups. Highlight the desired

group and press (SEL) to display the parameters within that group.

• Highlight a parameter and press (EDIT) to adjust the setting.

• Use and to adjust the setting. Press SAVE to accept the setting

shown. Press EXIT twice to return to the Main menu.

Notes for more complicated edits:

• With parameters that define a digital source, the setting Const can be used to fix the

value to constant 1 (C.TRUE) or 0 (C.FALSE).

• With parameters that define an analog or digital source, the setting Pointer can be

used to freely choose any parameter value (analog) or a specific bit of a packed

boolean parameter (digital) as the source:

• With an analog source, the parameter group

and parameter index are specified. After

selecting the group, press NEXT to move to the

index setting.

The text below the cursor reflects the current

setting.

After setting the index, press SAVE to accept

the value. Press CANCEL at any point to

discard any changes and to return to the

parameter list.

• With a digital source, the parameter group,

parameter index, and bit number are specified.

After setting an item, press NEXT to move to

the next.

The text below the cursor reflects the current

setting.

After the bit number is set, press SAVE to

accept the value. Press CANCEL at any point

to discard any changes and to return to the

parameter list.

Changing the language

By default, the language of the text shown is English. If desired, the language can be

changed as follows.

In the Main menu, make sure PARAMETERS is

highlighted, and press ENTER.

1501 AO1 src

P.01.06

PAR EDIT

CANCEL

SAVE

0106 Motor torque

LOC

1002 Ext1 start in1

P.02.01.00

PAR EDIT

CANCEL

LOC

PARAMETERS

ASSISTANTS

CHANGED PAR

EXIT ENTER

MAIN MENU 1

LOC

6 Quick Start-up Guide for ACS850 with Standard Control Program

Navigate to parameter group 99 Start-up data and

press SEL. Note that the list will wrap around in

either direction between groups 99 and 01 – it is

quicker to press for group 99.

Make sure parameter “9901 Language” is

highlighted and press EDIT.

Select the desired language and press SAVE.

Press EXIT twice to return to the Main menu.

Assistants

The start-up procedures described below make use of assistants. These are routines

that guide the user through the essential parameter settings.

1 – Application macro selection

In the Main menu, highlight ASSISTANTS and press

ENTER.

Highlight Application Macro and press OK.

99 Start-up data

01 Actual values

02 I/O values

03 Control values

04 Appl values

EXIT

SEL

PAR GROUPS 99

LOC

9901 Language

English

9904 Motor type

9905 Motor ctrl mode

9906 Mot nom current

PARAMETERS

EXIT

EDIT

LOC

9901 Language

Deutsch

PAR EDIT

CANCEL

SAVE

[0407 hex]

LOC

PARAMETERS

ASSISTANTS

CHANGED PAR

EXIT ENTER

MAIN MENU 1

LOC

Select assistant

Application Macro

Motor Set-up

Start/Stop Control

EXIT

OK

CHOICE

LOC

Quick Start-up Guide for ACS850 with Standard Control Program 7

Application macros are pre-defined parameter

settings that can be used as a basis for user

applications. The following macros are available:

• Factory (for speed control applications where a

simple start/stop interface is required)

• Hand/Auto (for speed control applications where

two external control devices are used)

• PID control (for process control applications

such as closed-loop pressure, level or flow control

systems)

• Torque control (for torque and/or speed control

of motor)

• Sequential control (for speed control

applications in which multiple constant speeds

and acceleration/deceleration ramps are needed

and are sequenced).

More information on the macros is available in the

Firmware Manual.

Highlight one of the macros and press OK.

Parameter defaults for the macro

are applied.

After the text “Done OK” appears on the control panel, press OK to complete the

firmware assistant.

2 – Motor set-up

Ensure you have the motor nameplate and encoder data (if needed) at hand.

In the Main menu, highlight ASSISTANTS and press

ENTER.

Highlight Motor Set-up and press OK.

The assistant will guide you through the motor set-

up.

Select the motor type, AM (asynchronous squirrel

cage AC motor) or PMSM (permanent magnet

synchronous motor).

99.04 Motor type

PARAMETERS

ASSISTANTS

CHANGED PAR

EXIT ENTER

MAIN MENU 1

LOC

Select assistant

Application Macro

Motor Set-up

Start/Stop Control

EXIT

OK

CHOICE

LOC

8 Quick Start-up Guide for ACS850 with Standard Control Program

Select the motor control mode. DTC is suitable for

most cases.

Scalar mode is recommended if

• the nominal current of the motor is less than 1/6

of the nominal current of the drive,

• the drive is used for test purposes with no motor

connected, or

• the drive controls multiple motors and the number

of motors connected is variable.

99.05 Motor ctrl mode

Enter the motor data from the motor nameplate.

Asynchronous motor nameplate example:

Permanent magnet motor nameplate example:

Note: Set the motor data to

exactly the same value as on the

motor nameplate. For example, if

the motor nominal speed is 1470

rpm on the nameplate, setting the

value of parameter 99.09 Mot

nom speed to 1500 rpm results in

incorrect operation of the drive.

If D (delta) data is chosen, then

connect the motor in delta.

If Y (star) data is selected, then

connect the motor in star.

• motor nominal current

Allowed range: approximately 1/6 × I

Hd

… 2 × I

Hd

of

the drive (0…2 × I

Hd

if parameter 99.05 Motor ctrl

mode = Scalar).

99.06 Mot nom current

M2AA 200 MLA 4

1475

1470

1475

1770

32.5

56

34

59

54

59

0.83

3GAA 202 001 - ADA

180

IEC 34-1

6210/C36312/C3

Cat. no

35

30

50

60

690 Y

400 D

660 Y

380 D

415 D

440 D

V

Hz kW

r/min A

cos

IA/IN

t

E/s

Ins.cl. F

IP 55

No

IEC 200 M/L 55

3

motor

ABB Motors

3 ~ motor M2BJ 280SMB 10 B3

No 3424522

A

BB Motors

Ins.cl. F IP 55

V

400 D

Hz

50

kW

55

r/min

600

A

103

cos

M

0.97

IA/IN

t

E/s

Prod. code 2GBJ285220-ADA405445477

6316/C3

630kg

IEC 34-1

S1 SPEC INSUL.

JK-21640-1

Quick Start-up Guide for ACS850 with Standard Control Program 9

• motor nominal voltage

Allowed range: 1/6 × U

N

… 2 × U

N

of the drive. (U

N

refers to the highest voltage in each nominal voltage

range).

With permanent magnet motors, the nominal

voltage is the BackEMF voltage (at motor nominal

speed). If the voltage is given as voltage per rpm,

e.g. 60 V per 1000 rpm, the voltage for 3000 rpm

nominal speed is 3 × 60 V = 180 V.

Note that the nominal voltage is not equal to the

equivalent DC motor voltage (E.D.C.M.) value given

by some motor manufacturers. The nominal voltage

can be calculated by dividing the E.D.C.M. voltage

by 1.7 (= square root of 3).

99.07 Mot nom voltage

• motor nominal frequency

With permanent magnet motor: If the frequency is

not given on the motor nameplate, it has to be

calculated using the following formula:

f = n × p /60

where p = number of pole pairs, n = motor nominal

speed.

99.08 Mot nom freq

• motor nominal speed 99.09 Mot nom speed

• motor nominal power 99.10 Mot nom power

The following motor data parameters can be set to improve control accuracy. If not

known, set the values to 0.

• motor nominal cos



(not applicable for permanent

magnet motors)

99.11 Mot nom cosfii

• motor nominal shaft torque 99.12 Mot nom torque

The following parameters define operation limits to protect the driven equipment.

• maximum speed

For the Normal and Reduced ID runs (see below),

this value should be higher than 55% of the motor

nominal speed defined earlier.

20.01 Maximum speed

• minimum speed

For the Normal and Reduced ID runs (see below),

this value should be less than or equal to 0 rpm.

20.02 Minimum speed

• maximum current

This value should be higher than the motor nominal

current defined earlier.

20.05 Maximum current

10 Quick Start-up Guide for ACS850 with Standard Control Program

• maximum torque

For the Normal ID run (see below), this value should

be at least 100% of motor nominal torque defined

earlier.

20.07 Maximum torque1

• minimum torque 20.08 Minimum torque1

The question “Do you want to perform id-run now?” is displayed. The ID run

(identification run) will identify the characteristics of the motor for optimum control.

If you do not wish to perform the ID run at this point, select No to complete the Motor

Set-up firmware assistant. Proceed to section 3 – Start/Stop configuration.

If you wish to perform the ID run, continue with the following steps BEFORE selecting

Yes.

WARNING! With Normal or Reduced ID run the motor will run at up to

approximately 50…100% of the nominal speed during the ID run. ENSURE

THAT IT IS SAFE TO RUN THE MOTOR BEFORE PERFORMING THE ID

RUN!

Check the direction of rotation of the motor. During

the run (Normal or Reduced), the motor will rotate in

the forward direction.

Ensure the Safe Torque Off and emergency stop

circuits (if present) are closed.

Select Yes and press OK.

Select the ID run method.

The ID run will be performed at the next start of the

drive.

99.13 Idrun mode

NORMAL ID run should be selected whenever

possible.

Note: The driven machinery must be de-coupled

from the motor with Normal ID run:

• if the load torque is higher than 20%, or

• if the machinery is not able to withstand the

nominal torque transient during the ID run.

The REDUCED ID run should be selected instead of

the Normal ID run if the mechanical losses are

higher than 20%, i.e. the motor cannot be

de-coupled from the driven equipment, or full flux is

required to keep the motor brake open (conical

motor).

Forward

When drive output phases U2,

V2 and W2 are connected to the

corresponding motor terminals:

Reverse

Quick Start-up Guide for ACS850 with Standard Control Program 11

The STANDSTILL ID run should be selected only if

the Normal or Reduced ID run is not possible due to

the restrictions caused by the connected mechanics

(e.g. with lift or crane applications).

Notes:

• The motor shaft must NOT be locked and the load

torque must be < 20% during Normal or Reduced

ID run. With permanent magnet motor this

restriction also applies when Standstill ID run is

selected.

• Mechanical brake is not opened by the logic for

the ID run.

• The ID run cannot be performed if parameter

99.05 Motor ctrl mode = Scalar.

Start the motor (by pressing the START button) to

activate the ID run.

ID run is indicated by alarm ID-RUN on the panel

display.

Alarm: ID-RUN

After the text “Done OK” appears on the control panel, press OK to complete the

firmware assistant.

3 – Start/Stop configuration

In the Main menu, highlight ASSISTANTS and press

ENTER.

Highlight Start/Stop Control and press OK.

The following parameters will be set.

Note: Depending on the selections you make, the

routine may skip some of the parameters listed

below.

Select the start/stop function and signal sources for

external control location 1 (EXT1). First, program

parameter 10.01 (start function), then 10.02 and

10.03 to choose the sources of the start signal.

The choices for parameter 10.01 are:

In1: The signal defined in parameter 10.02 is the

source for the start signal (0 = Stop, 1 = Start).

10.01 Ext1 start func

10.02 Ext1 start in1

10.03 Ext1 start in2

PARAMETERS

ASSISTANTS

CHANGED PAR

EXIT ENTER

MAIN MENU 1

LOC

Select assistant

Application Macro

Motor Set-up

Start/Stop Control

EXIT

OK

CHOICE

LOC

12 Quick Start-up Guide for ACS850 with Standard Control Program

3-wire: Start/Stop commands are determined on the

basis of the two sources selected by parameters

10.02 and 10.03.

In1F In2R: The signal defined in parameter 10.02

starts the drive in the forward direction, and the

signal defined in 10.03 will start the drive in reverse.

In1St In2Dir: The signal defined in parameter 10.01

will start the drive (0 = Stop, 1 = Start). The signal

defined in 10.03 will change the motor direction

(0 = forward, 1 = reverse).

Select the start/stop function and signal sources for

external control location 2 (EXT2).

The selections are as with EXT1 above.

10.04 Ext2 start func

10.05 Ext2 start in1

10.06 Ext2 start in2

Define the signal source to switch between external

control locations EXT1 and EXT2 (0 = EXT1, 1 =

EXT2).

12.01 Ext1/Ext2 sel

Select the motor start function.

Automatic is the best all-round setting that also

enables flying start (starting when the motor is

rotating).

Fast involves pre-magnetization of the motor and

should be selected if a high break-away torque is

required.

Const time should be selected if a constant pre-

magnetization time is required. The time is set by

parameter 11.02 DC-magn time.

11.01 Start mode

Select the stop mode.

Coast: The power to the motor is cut off. The motor

is left to coast to a stop.

Ramp: The motor is stopped by decelerating along

the active deceleration ramp (to be defined later).

11.03 Stop mode

Select the source of the run enable signal.

If the signal is switched off, the drive will not start, or

coasts to stop if running. 1 = Run enable signal on.

10.11 Run enable

Select the source of the emergency stop OFF3

signal.

If the signal is removed (in other words, changes to

0), the drive will stop along the emergency stop

ramp (defined by parameter 22.12 Em stop time).

10.13 Em stop off3

State of source 1

(via par. 10.02)

State of source 2

(via par. 10.03)

Command

0

-

> 1 1 Start

Any 1

-

> 0 Stop

Any 0 Stop

Quick Start-up Guide for ACS850 with Standard Control Program 13

After the text “Done OK” appears on the control panel, press OK to complete the

firmware assistant.

4 – Reference selection

In the Main menu, highlight ASSISTANTS and press

ENTER.

Highlight Reference select and press OK.

The following parameters will be set.

Note: Depending on the selections you make, the

routine may skip some of the parameters listed

below.

Select the control mode for external control

locations EXT1 and EXT2.

Speed: Speed control.

Torque: Torque control.

Min, Max, Add: Torque reference and speed

controller output are compared and the

mathematical function is applied (smaller, greater,

addition).

Depending on the selections, the speed or torque

reference source (or both) is defined next.

12.03 Ext1 ctrl mode

12.05 Ext2 ctrl mode

Speed reference set-up

Choose the number of constant speeds (if any) to use.

If you select any constant speeds, you are asked if the start direction should affect the

constant speed direction.

No: The sign of the constant speed directly determines the running direction when the

constant speed is activated.

Yes: The sign of the constant speed is multiplied by the value of the Direction signal to

determine the running direction when the constant speed is activated.

PARAMETERS

ASSISTANTS

CHANGED PAR

EXIT ENTER

MAIN MENU 1

LOC

Select assistant

Motor Set-up

Start/Stop Control

Reference select

EXIT

OK

CHOICE

LOC

14 Quick Start-up Guide for ACS850 with Standard Control Program

You are now asked if each constant speed selector should activate one constant speed.

No: Constant speeds 1…7 are activated by the sources selected by parameters 26.02,

26.03 and 26.04 as follows:

Yes: Constant speeds 1…3 are activated by the sources selected by parameters 26.02,

26.03 and 26.04 respectively.

Set the constant speed selector sources. 26.02 Const speed sel1

26.03 Const speed sel2

26.04 Const speed sel3

Enter the constant speeds. 26.06 Const speed1…

Select the source of the speed reference signal. 21.01 Speed ref1 sel

Define the absolute minimum limit for the speed

reference. This limit applies for both the positive and

negative ranges.

21.09 SpeedRef min abs

Define the speed scaling used for the acceleration/

deceleration times. Define the acceleration/

deceleration times.

The diagram below shows the effect of parameter

19.01 Speed scaling on the acceleration/

deceleration times.

Note: Acceleration/deceleration times may be

automatically extended by the existing torque limits.

19.01 Speed scaling

22.02 Acc time1

22.04 Acc time2

22.03 Dec time1

22.05 Dec time2

Source defined by

par. 26.02

Source defined by

par. 26.03

Source defined by

par. 26.04

Constant speed active

000None

1 0 0 Constant speed 1

0 1 0 Constant speed 2

1 1 0 Constant speed 3

0 0 1 Constant speed 4

1 0 1 Constant speed 5

0 1 1 Constant speed 6

1 1 1 Constant speed 7

Time

Speed

19.01

22.02 or

22.04

22.03 or

22.05

Acc. Dec.

0

Quick Start-up Guide for ACS850 with Standard Control Program 15

Select the source to switch between acceleration/

deceleration ramp pairs 1 and 2.

0 = Acceleration time 1/Deceleration time 1 are in

force, 1 = Acceleration time 2/Deceleration time 2

are in force.

22.01 Acc/Dec sel

Torque reference set-up

Select the source of the torque reference signal. 24.01 Torq ref1 sel

Define the maximum and minimum torque

references.

24.03 Maximum torq ref

24.04 Minimum torq ref

Define the times for the torque reference to increase

from zero to nominal motor torque (ramp up) and

vice versa (ramp down).

24.06 Torq ramp up

24.07 Torq ramp down

Analog input AI1/AI2 set-up (if either is selected as speed or torque reference source)

Define the filter time constant for the analog input. 13.01 AI1 filt time or

13.06 AI2 filt time

Define the maximum and minimum values for the

analog input.

13.02 AI1 max or

13.07 AI2 max

13.03 AI1 min or

13.08 AI2 min

63

%

100

T

t

O = I × (1 - e

-t/T

)

I = filter input (step)

O = filter output

t = time

T = filter time constant

Unfiltered signal

Filtered signal

16 Quick Start-up Guide for ACS850 with Standard Control Program

Define the scaled values that correspond to the

maximum and minimum values defined at the

previous step. This is useful if full speed is required

at lower analog input values.

13.04 AI1 max scale or

13.09 AI2 max scale

13.05 AI1 min scale or

13.10 AI2 min scale

After the text “Done OK” appears on the control panel, press OK to complete the

firmware assistant and the start-up procedure.

AI (scaled)

AI (mA/V)

13.04/13.09

13.02/13.07

13.03/13.08

13.05/13.10

Quick Start-up Guide til ACS850 med Standard Control Program 17

Quick Start-up Guide til ACS850 med Standard

Control Program

Om denne vejledning

Denne vejledning indeholder den grundlæggende procedure, der skal følges ved

opstart af et ACS850-drev (med Standard Control Program). Under proceduren er

drevet aktiveret ved hjælp af ACS850-betjeningspanelet.

Bemærk! Det er kun de af betjeningspanelets funktioner, der er nødvendige under

proceduren, som er beskrevet. Alle oplysningerne om brugen af af betjeningspanelet

findes i ACS850-standardstyreprogram Firmwaremanual (3AUA0000054535 (på

dansk)).

Sikkerhedsinstruktioner

ADVARSEL! Al elektrisk installation og alt vedligeholdelsesarbejde på

drevet må kun udføres af en autoriseret installatør.

Arbejd aldrig på drevet, bremsechopperkredsen, motorkablet eller motoren, når

netspændingen er tilsluttet drevet. Sørg altid for at sikre dette ved at måle, at der ikke

er nogen spænding til stede.

18 Quick Start-up Guide til ACS850 med Standard Control Program

Opstartsprocedure

Sikkerhed

Opstartsproceduren må kun gennemføres af en kvalificeret elektriker.

Sikkerhedsinstruktionerne skal følges under opstartsproceduren. Se

sikkerhedsinstruktionerne på de første sider af den tilhørende hardwaremanual.

Kontroller installationen. Se installationstjeklisten i den tilhørende hardware-manual.

Kontroller, at start af motoren ikke medfører fare.

Belastningsmaskinen frakobles, hvis:

• Der er risiko for ødelæggelse i tilfælde af forkert omløbsretning, eller

• en normal identifikationstest kræves under opstarten af drevet, hvis

belastningsmomentet er højere end 20 %, eller hvis maskinen ikke kan tåle det

nominelle transiente moment under identifikationstesten.

Opstart, grundlæggende om betjeningspanel

Slut betjeningspanelet til drevet ved hjælp af det

tilhørende Kategori 5E-kabel.

Start drevet op. Efter nogle få øjeblikke viser panelet

Outputmode (højre).

Bemærk! Outputmode vises skiftevis med "Alarm

2021 MOTORDATA MANGLER", indtil en assistent

startes senere i proceduren.

Skift til lokal styring for at sikre, at ekstern styring er

deaktiveret, ved at trykke på tasten på

betjeningspanelet. Lokalstyring indikeres med

teksten "LOK" i den øverste række på displayet.

De to bokse i den nederste række af visningen

angiver funktionen af de to taster og .

Indholdet af boksene afhænger af de synlige

menuvalg.

Tryk på (MENU) for at få adgang til

hovedmenuen.

Det ønskede valg markeres i menuen. Tryk på

tasterne og for at foretage et nyt

valg, og aktivér ved at trykke på (ENTER).

Hovedmenuen er startpunktet for de procedurer, der

er beskrevet herunder.

00 A

00 Hz

0 %0.

0.

REM

RETNING

MENU

0,00rpm

LOK

REM

00 A

00 Hz

0 %0.

0.

LOK

RETNING

MENU

0,00rpm

PARAMETRE

ASSISTENT

ÆNDRET PAR

EXIT ENTER

HOVEDMENU 1

LOK

Quick Start-up Guide til ACS850 med Standard Control Program 19

Justering af parameterværdier

Bemærk!

• Du kan altid trykke på (CANCEL eller EXIT) for at vende tilbage til det forrige

niveau.

• Som standard er det ikke alle parametre, der er synlige. Angiv parameteren 16.15

Param liste valg til Load lang for at gøre alle parametre synlige.

Sådan justeres en parameter i en assistent:

• Brug tasterne og for at justere indstillingen. Tryk på GEM for at

acceptere den viste indstilling og fortsætte til den næste parameter.

Sådan justeres en parameter på ethvert tidspunkt:

• Fremhæv i hovedmenuen PARAMETRE, og tryk på (ENTER).

• Brug og til at søge i listen over parametergrupper. Fremhæv den

ønskede gruppe, og tryk på (VALG) for at få vist parametrene i gruppen.

• Fremhæv en parameter, og tryk på (REDIGER) for at justere indstillingen.

• Brug og til at justere indstillingen. Tryk på GEM for at acceptere den

viste indstilling. Tryk på EXIT to gange for at gå tilbage til hovedmenuen.

Bemærkninger til mere komplicerede redigeringer:

• Når det drejer sig om parametre, der definerer en digital kilde, kan indstillingen

Konstant bruges til at fastsætte værdien til konstanten 1 (C.SAND) eller

0 (C.FALSK).

• Når det drejer sig om parametre, der definerer en analog eller digital kilde, kan

indstillingen Pointer bruges til frit at vælge enhver parameterværdi (analog) eller en

specifik del af en pakket boolesk parameter (digital) som kilden:

• Når det drejer sig om en analog kilde, er

parametergruppen og parameterindekset

angivet. Når gruppen er valgt, trykkes der på

NÆSTE for at flytte til indeksindstillingerne.

Teksten under markøren angiver den aktuelle

indstilling.

Når indekset er indstillet, trykkes der på GEM

for at acceptere værdien. Tryk på CANCEL på

ethvert tidspunkt for at kassere eventuelle

ændringer og vende tilbage til parameterlisten.

• Med en digital kilde er parametergruppen,

parameterindekset og bitnummeret

specificeret. Når et element er indstillet, skal

der trykkes på NÆSTE for at gå videre til det

næste.

Teksten under markøren angiver den aktuelle

indstilling.

Når bitnummeret er indstillet, trykkes der på

GEM for at acceptere værdien. Tryk på

CANCEL på ethvert tidspunkt for at kassere

eventuelle ændringer og vende tilbage til

parameterlisten.

1501 AO1 signalkilde

P.01.06

PAR ÆNDRING

CANCEL

GEM

0106 Motor moment

LOK

1002 EKS1 startKilde1

P.02.01.00

PAR ÆNDRING

CANCEL

NÆSTE

0201 DI-Status

LOK

20 Quick Start-up Guide til ACS850 med Standard Control Program

Ændring af sproget

Engelsk er standardsproget for den viste tekst. Hvis det ønskes, kan sproget ændres på

følgende måde.

Kontrollér, at PARAMETRE er markeret i

hovedmenuen, og tryk på ENTER.

Naviger til parametergruppe 99 Opstartsdata, og

tryk på VALG. Bemærk, at listen fortsætter i hver

retning mellem grupperne 99 og 01 – det er

hurtigere at trykke på for gruppe 99.

Kontrollér, at parameter "9901 Sprog" er markeret,

og tryk på REDIGER.

Vælg det ønskede sprog, og tryk på GEM.

Tryk på EXIT to gange for at gå tilbage til

hovedmenuen.

Assistenter

Opstartsprocedurerne, der er beskrevet herunder, gør brug af assistenter. Dette er

rutiner, der guider brugeren gennem de vigtigste parameterindstillinger.

1 – Valg af applikationsmakro

Markér ASSISTENT i hovedmenuen, og tryk på

ENTER.

Markér Application Macro, og tryk på OK.

PARAMETRE

ASSISTENT

ÆNDRET PAR

EXIT ENTER

HOVEDMENU 1

LOK

99 Opstartsdata

01 Aktuel værdi

02 I/O værdi

03 Kontrol værdi

04 Applikations værdi

EXIT

SEL

PAR GRUPPER 99

LOK

9901 Sprog

Engelsk

9904 Motor type

9905 Motor styre mode

9906 Mot nom strøm

PARAMETRE

EXIT

ÆNDRE

LOK

9901 Sprog

Deutsch

PAR ÆNDRING

CANCEL

GEM

[0407 hex]

LOK

PARAMETRE

ASSISTENT

ÆNDRET PAR

EXIT ENTER

HOVEDMENU 1

LOK

Vælg assistent

Application Macro

Motoropsætning

Start/Stop styring

EXIT

OK

VALG

LOK

Страница загружается...

ABB ACS850 series Quick Start Up Manual

Похожие модели бренда

Модели других брендов