TECHNICAL PASSPORT
ПАСПОРТ ТЕХНИЧЕСКОГО ИЗДЕЛИЯ
WM 1477
WASHING MACHINES
СТИРАЛЬНЫЕ МАШИНЫ
2
TECHNICAL PASSPORT ENGLISH
Washing Machines
1. GENERAL SAFETY RULES ..................................................................................................................4
2. INSTALLATION ........................................................................................................................................6
3. PRACTICAL TIPS .....................................................................................................................................11
4. MAINTENANCE AND CLEANING ....................................................................................................12
5. QUICK USER GUIDE .............................................................................................................................. 13
6. CONTROLS AND PROGRAMS ........................................................................................................... 13
7. THROUBLESHOOTING AND WARRANTY ...................................................................................21
CONTENTS
3
ENGLISH TECHNICAL PASSPORT
Washing Machines
Carefully read this manual for
correct and safe appliance use and for
helpful tips on effi cient maintenance.
Only use the washing machine after
carefully reading these instructions.
We recommend you always keep this
manual on hand and in good condition
for any future owners.
Please check that the appliance is
delivered with this instruction manual,
warranty certifi cate, service centre
address and energy effi ciency label.
Also check that plugs, drain hose
support hook and liquid detergent or
bleach tray (only on some models) are
included. We recommend you keep all
these components.
FOR U.K. ONLY
On receipt of your appliance
please check it carefully for damage.
Any damage found must be reported
to the delivery driver immediately.
Alternatively damage found must be
reported to the retailer within 2 days of
receipt.
Each product is identifi ed by a
unique 16- character code, also called
the “serial number”, printed on the
sticker. This can be found inside the
door opening. This code is a unique
code for your product that you will
need to register the product warranty,
or if you need to contact the Customer
Service Centre.
Environmental conditions
This appliance is marked according
to the European directive 2012/19/
EU on Waste Electrical and Electronic
Equipment (WEEE).
WEEE contains both polluting
substances (which can cause negative
consequences for the environment)
and basic components (which can be
re-used). It is important to have WEEE
subjected to specifi c treatments, in
order to remove and dispose properly
all pollutants, and recover and recycle
all materials. Individuals can play an
important role in ensuring that WEEE
does not become an environmental
issue; it is essential to follow some
basic rules:
WEEE should not be treated as
household waste;
WEEE should be handed over to
the relevant collection points managed
by the municipality or by registered
companies. In many countries, for large
WEEE, home collection could be present.
In many countries, when you buy
a new appliance, the old one may be
returned to the retailer who has to
collect it free of charge on a one-to-
one basis, as long as the equipment is
of equivalent type and has the same
functions as the supplied equipment.
4
TECHNICAL PASSPORT ENGLISH
Washing Machines
1. GENERAL SAFETY RULES
This appliances is intended
to be used in household and similar
applications such as:
Staff kitchen areas in
shops, offi ces and other working
environments;
Farm houses;
By clients in hotels,
motels and other residential type
environments;
Bed and breakfast type
environments. A different use of this
appliance from household environment
or from typical housekeeping functions,
as commercial use by expert or trained
users, is excluded even in the above
applications. If the appliance is used
in a manner inconsistent with this it
may reduce the life of the appliance
and may void the manufacturer’s
warranty. Any damage to the appliance
or other damage or loss arising
through use that is not consistent
with domestic or household use (even
if located in a domestic or household
environment) shall not be accepted by
the manufacturer to the fullest extent
permitted by law.
This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved.
Children shall not play with
the appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Children should be supervised to
ensure that they do not play with the
appliance.
Children of less than 3
years should be kept away unless
continuously supervised.
If the supply cord is damaged,
it must be replaced by a special
cord or assembly available from the
manufacturer or its service agent.
Only use the hose-sets supplied
with the appliance for the water supply
connection (do not reuse old hose-
sets).
Water pressure must be between
0.05 MPa and 0.8 MPa.
Make sure carpets or rugs do
not obstruct the base or any of the
ventilation openings.
After installation, the appliance
must be positioned so that the plug is
accessible.
The maximum load capacity of
dry clothes depends on the model used
(see control panel).
To consult the product technical
specifi cation please refer to the
manufacturer website.
5
ENGLISH TECHNICAL PASSPORT
Washing Machines
Electrical connections and
safety instructions
The technical details (supply
voltage and power input) are indicated
on the product rating plate
Make sure that the electrical
system is earthed, complies with all
applicable law and that the (electricity)
socket is compatible with the plug of
the appliance. Otherwise, seek qualifi ed
professional assistance.
The use of converters, multiple
sockets or extension cords is strongly
advised against
Before cleaning or maintaining
the washing machine, unplug the
appliance and turn off the water tap.
Do not pull on the power cord or
appliance to unplug the machine.
Make sure there is no water in
the drum before opening the door.
WARNING:
water may reach very high
temperatures during the wash cycle.
Do not expose the washing
machine to rain, direct sunlight or
other weather elements. Protect from
possible freezing.
When moving, do not lift the
washing machine by the knobs or
detergent drawer; during transport,
never rest the door on the trolley. We
recommend two people lift the washing
machine.
In the event of fault and/or
malfunction, turn off the washing
machine, close the water tap and
do not tamper with the appliance.
Immediately contact the Customer
Service Centre and only use original
spare parts. Failure to observe these
instruction may jeopardise appliance
safety.
6
TECHNICAL PASSPORT ENGLISH
Washing Machines
2. INSTALLATION
Remove the 2 or 4 transportation
screws (A) on the back and remove the
2 or 4 fl at washers, rubber bungs and
plastic spacer tubes (B) as illustrated in
fi gure 1.
If the washing machine is built-
in, unscrew the 3 or 4 transportation
screws (A) and remove the 3 or 4 fl at
washers, rubber bungs and plastic
spacer tubes (B).
During the removal of the screws
occasionally spacer tubes fall inside the
product, these can be remove by tilting
the product forward and recovering
them from the fl oor or inside the base
of the machine.
Cover the open transportation
screw holes with the 2 or 4 plastic caps
included in the instruction bag.
WARNING:
keep packaging materials away
from children.
Place the corrugated plastic
sheet, found on top of the appliance
during the unpacking process, into the
base of the appliance as shown in fi gure
2 (according to the model, consider
version A, B or C).
In some models this operation will not
be necessary, because the corrugated
plastic sheet will be already placed on
the bottom of the appliance.
7
ENGLISH TECHNICAL PASSPORT
Washing Machines
Instructions for mounting the
furniture door
Position the template onto
the reverse of the furniture door. It
is possible to mount the hinges and
closure magnet on the right or left-hand
side depending on your requirements.
Mark the screw hole positions, then drill
out these positions.
Fix the hinges in place with the 4
screws provided (A).
Fix the magnet (B) in place using
screw (C).
Mount the plate (D) on the right
or left-hand side, depending on your
installation requirements. Place the
plastic support (E) under the plate and
fi x it in position with screw (F).
Snap mount cap (G) in the lower
position.
8
TECHNICAL PASSPORT ENGLISH
Washing Machines
Mount the furniture door to the
front of the washer using the hinges.
Place the spacers under the hinges (I)
and then fi x in position with screw (H).
We suggest mounting the furniture
door so that it opens towards the left,
which is the same direction as the
porthole door. This will leave more
space when you are loading washing
into the appliance.
Slide the washer into an opening
of the size indicated in the diagram
opposite. A furniture plinth may be run
across the front of the appliance, but
its height will be dictated by the height
the washer is set at.
The 4 adjustable feet allow the
height of the washer to be adjusted
from 820 mm to a maximum of 840
mm. To adjust the height, you should
remove the nuts fi tted to each foot
and replace these with the 5 mm nuts
supplied. Raise the feet to your desired
height and then fully tighten the lock
nut to the base of the washer.
9
ENGLISH TECHNICAL PASSPORT
Washing Machines
Hydraulic connections
Connect the water hose to the
water supply tap (fi g. 3) only using the hose
supplied with the appliance (do not reuse
old hose-sets).
SOME MODELS may include one or
more of the following features:
HOT&COLD (fi g. 4):
water mains connection settings with
hot and cold water for higher energy
savings. Connect the grey tube to the cold
water tap % and the red one to the hot
water tap. The machine can be connected to
the cold water tap only: in this case, some
programs may start a few minutes later.
AQUASTOP (fi g. 5):
a device located on the supply tube that
stops water fl ow if the tube deteriorates;
in this case, a red mark will appear in the
window “A” and the tube must be replaced.
To unscrew the nut, press the one-way lock
device «B».
AQUAPROTECT - SUPPLY TUBE
WITH GUARD (fi g. 6):
Should water leak from the primary
internal tube «A», the transparent
containment sheath «B» will contain water
to permit the washing cycle to complete. At
the end of the cycle, contact the Customer
Service Centre to replace the supply tube.
Setting
The washing machine should be
installed in its fi nal position such that the
water fi ll hose is not kinked or trapped.
The corrugated drain hose should be
inserted into suitable drain pipe of
between 50 cm and 85 cm height above
the fl oor using the curved drain hose
support. If an under sink connection is
used the drain hose must be routed above
the sink overfi ll opening to prevent back
siphoning. Care must be taken to avoid
kinking or trapping the drain hose (fi g. 7).
10
TECHNICAL PASSPORT ENGLISH
Washing Machines
Level the appliance using the
feet as illustrated in fi gure 8:
a. turn the nut clockwise to release
the screw;
b. rotate the foot to raise or lower it
until it touches to the fl oor;
c. lock the foot, screwing in the nut,
until it tightens against to the bottom
of the washing machine.
Plug in the appliance.
WARNING:
contact the Customer Service
Centre should the power cord need
replacement.
Detergent drawer
The detergent draw is split into 3
compartments as illustrated in fi gure 9:
compartment «1»: for prewash
detergent;
compartment « »: for special
additives, softeners, starch fragrances, etc.;
WARNING:
only use liquid products;
the washing machine is set to
automatically dose additives at each
cycle during the last rinse.
compartment «2»: for washing
detergent.
WARNING:
some detergents are not designed
for use in the dispenser drawer but
are supplied with their own dispenser
that is placed in the drum directly.
WARNING:
installation faults are not covered
by the manufacturers warranty.
11
ENGLISH TECHNICAL PASSPORT
Washing Machines
3. PRACTICAL TIPS
Load tips
When sorting laundry, make
sure:
have eliminated metallic
objects such as hair clips, pins, coins,
from laundry;
to have buttoned pillow cases,
closed zips, tied loose belts and long
robe ribbons;
to have removed rollers, hooks
or clips from curtains;
to have carefully read clothing
washing labels;
to have removed any persistent
stains using specifi c detergents.
When washing rugs, bedcovers or
other heavy clothing, we recommend you
avoid the spinning cycle.
To wash wool, make sure the item
can be machine washed. Check the fabric
label.
Helpful suggestions for the user
A guide environmentally friendly and
economic use of your appliance.
Maximise The Load Size
Achieve the best use of energy,
water, detergent and time by using the
recommended maximum load size.
Save up to 50% energy by washing a
full load instead of 2 half loads.
Do you need to pre-wash?
For heavily soiled laundry only!
SAVE detergent, time, water and
between 5 to 15% energy consumption
by NOT selecting Prewash for slight to
normally soiled laundry.
Is a hot wash required?
Pretreat stains with stain remover
or soak dried in stains in water before
washing to reduce the necessity of a hot
wash programme. Save energy by using
a low temperature wash programme.
Before using a drying
programme (WASHER-DRYERS)
SAVE energy and time by selecting
a high spin speed to reduce the water
content in laundry before using a drying
programme.
Following is a quick guide with tips
and recommendations on detergent
use at the various temperatures. In any
case, always read the instructions on the
detergent for correct use and doses.
When washing heavily soiled whites, we
recommend using cotton programs of 60°C
or above and a normal washing powder
(heavy duty) that contains bleaching
agents that at medium/high temperatures
provide excellent results.
For washes between 40°C and 60°C
the type of detergent used needs to be
appropriate for the type of fabric and level
of soiling. Normal powders are suitable
for “white” or colour fast fabrics with high
soiling, while liquid detergents or “colour
protecting” powders are suitable for
coloured fabrics with light levels of soiling.
For washing at temperatures below 40°C
we recommend the use of liquid detergents
or detergents specifi cally labeled as
suitable for low temperature washing.
For washing wool or silk, only use
detergents specifi cally formulated for
these fabrics.
12
TECHNICAL PASSPORT ENGLISH
Washing Machines
MAINTENANCE
AND CLEANING
To clean the washing machine
exterior, use a damp cloth, avoiding
abrasives, alcohol and/or solvents. To
maintain a good wash performance we
recommend that the soap drawer and
pump fi lters are regularly cleaned. A
monthly service wash, using a proprietary
cleaner is also recommended.
Drawer cleaning
We recommend you clean the
drawer to avoid accumulating detergent
and additive residue.
To do this, extract the drawer
using slight force, clean it with running
water and reinsert it in its housing.
Ensure the siphon cap is correctly
refi tted.
Filter cleaning
The washing machine comes
with a special fi lter able to trap large
residue, such as buttons or coins, which
could clog the drain.
Only available on certain models:
pull out the corrugated hose, remove
the stopper and drain the water into a
container.
Ensure all the water has been
emptied from the drum.
Before unscrewing the fi lter,
we recommend you place an absorbent
cloth under it to keep the fl oor dry. A
small amount of water will come out
of the fi lter as you remove it - this is
normal.
Turn the fi lter counter-clockwise
to the limit stop.
Remove and clean the fi lter;
when fi nished, replace it turning it
clockwise. The fi lter handle will be
locked when it is not possible to turn
any further and the handle is horizontal.
Smearing a small amount of liquid soap
on the fi lter seal will help refi tting.
Repeat the previous steps in
reverse order to reassemble all parts.
Suggestions for moves or
prolonged disuse
Should the washing machine be
stored in an unheated room for a long
period of time, drain all water from tubes.
Unplug the washing machine.
Detach the tube from the
drainage system and clip on the rear of
the machine and lower it, fully draining
water into a bowl.
Secure the drain tube with the
drainage system and clip on the rear of
the machine when fi nished.
Keep the door glass and gasket clean.
The manufacturers warranty only
covers faults within the product of a
mechanical or electrical nature. Faults
caused by handling, installation or miss
use are not covered and may incur a
charge for any repair visit to resolve.
13
ENGLISH TECHNICAL PASSPORT
Washing Machines
5. QUICK USER GUIDE
This washing machine automatically
adjusts the level of the water to the
type and quantity of washing. This
system gives a reduction in energy
consumption and a saving in washing
times.
Program selection
Turn on the washing machine
and select the required program.
Adjust the washing temperature
if necessary and press the required
«option» buttons.
Press the START/PAUSE button to
start washing.
Should power go out when the washing
machine is running, a special memory
saves the settings and, when power
returns, the machine resumes the cycle
from where it left off.
At the end of the programme,
the message «End» will appear on the
display or, on some models, all wash
stage indicator lights will turn on.
Wait until the DOOR LOCKED light has
gone out before opening the door.
Turn off the washing machine.
For any type of wash, see the program
table and follow the operating sequence
as indicated.
Technical data
Water pressure:
min 0.05 Mpa / max 0.8 Mpa
(0.05 MPa dispenses approximately
1 litre of water in 10 seconds)
Spin r.p.m.: See rating plate.
Power input / Power current fuse
amp / Supply voltage: See rating plate.
6. CONTROLS AND PROGRAMS
A Programme selector with OFF
position
B START/PAUSE button
C DELAY START button
D OPTIONS button
E RAPID / STAIN LEVEL button
F TEMPERATURE SELECTION button
G SPIN SPEED button
F+G KEY LOCK
H Digital display
I OPTIONS indicator lights
L DOOR LOCKED indicator light
N KEY LOCK indicator light
O TEMPERATURE SELECTION
indicator lights
P SPIN SPEED indicator lights
14
TECHNICAL PASSPORT ENGLISH
Washing Machines
Opening the door
A special safety device prevents the
door from being opened immediately
after the end of the cycle.
Wait for 2 minutes after the wash cycle
has fi nished and the «Door Security»
light has gone out before opening the
door.
PROGRAMME selector with OFF
position
When the programme selector is
turned the display lights up to show the
settings for the programme selected.
For energy saving, at the end of the
cycle or with an inactivity period, the
display level contrast will decrease.
N.B.: To switch the machine off, turn the
programme selector to the OFF position.
Press the START/PAUSE button to
start the selected cycle.
Once a programme is selected
the programme selector remains
stationary on the selected programme
till cycle ends.
Switch off the washing machine
by turning the selector to OFF.
The programme selector must be
returned to the OFF position at the
end of each cycle or when starting a
subsequent wash cycle prior to the next
programme being selected and started.
START/PAUSE button
Close the door BEFORE selecting the
button START/PAUSE.
Press to start the selected cycle.
When the START/PAUSE button has
been pressed, the appliance can take
few seconds before it starts working.
ADD OR REMOVE ITEMS
AFTER THE PROGRAMMES HAS
STARTED (PAUSE)
Press and hold the START/PAUSE
button for about 2 seconds (some
indicator light and the time remaining
indicator will fl ash, showing that the
machine has been paused).
Wait 2 minutes until the safety
device unlocks the door.
Before you open the door, please check
water level is below the door opening
to avoid fl ooding.
After you have added or removed
items, close the door and press the
START/PAUSE button (the programme
will start from where it left off).
CANCELLING THE PROGRAMME
To cancel the programme, set the
selector to the OFF position.
DELAY START button
This button allows you to pre-
programme the wash cycle to delay the
start of the cycle for up to 24 hours.
To delay the start use the
following procedure:
Select the required
programme.
Press the delay start button
once to activate it (h00 appears on
the display) and then press it again to
set a 1 hour delay (h01 appears on the
15
ENGLISH TECHNICAL PASSPORT
Washing Machines
display). The pre-set delay increases by
1 hour each time the button is pressed,
until h24 appears on the display, at
which point pressing the button again
will reset the delay start to zero.
Confi rm by pressing the
START/PAUSE button. The delay
countdown will begin and when it
has fi nished the programme will start
automatically.
It is possible to cancel the delay
start by turning the programme selector
to OFF.
If there is any break in the power supply
while the machine is operating, a special
memory stores the selected programme
and, when the power is restored, it
continues where it left OFF.
The option buttons should be selected
before pressing the START/PAUSE
button.
OPTIONS button
This button allows you to choose
between three different options:
- EXTRA RINSE
This option allows you to add
one rinse at the end of the washing
cycle and is useful for people with
delicate and sensitive skin, for which a
small amount of detergent residue can
cause irritations or allergies.
It is advisable to also use this
function for the children clothes and
for the washing of heavily soiled items,
which requires a lot of detergent to be
used, or for the washing of toweling
items whose fi bres mostly have the
tendency to hold the detergent.
- HYGIENE +
Activated when you set 60°C of
temperature. This option allows deep
cleaning of your clothes by maintaining
the same temperature for the whole
wash.
- EASY IRON
This function allows you to
minimizes creases as much as possible,
eliminating the intermediate spins or
reducing the intensity of the last one.
If an option is selected that is
not compatible with the selected
programme then the option indicator
light fi rst fl ashes and then goes off.
RAPID / STAIN LEVEL button
This button allows you to choose
between two different options,
depending on the selected programme.
- RAPID
The button becomes active when
you select the RAPID (14/30/44 Min.)
programme on the knob and allows
you to select one of three durations
indicated.
- STAIN LEVEL button
Once the programme has been
selected the wash time set for that
programme will be automatically
shown.
This option allows you to choose
between 3 levels of wash intensity
modifying the length of the programme,
16
TECHNICAL PASSPORT ENGLISH
Washing Machines
depending on how much the fabrics
are soiled (can only be used on some
programmes as shown in the table of
programmes).
TEMPERATURE SELECTION
button
This button allows you to change
the temperature of the wash cycles.
It is not possible to raise the
temperature over the maximum allowed
for the programme, in order to protect
the fabrics.
If you want carry out a cold wash
all the indicators must be off.
SPIN SPEED button
By pressing this button, it is
possible to reduce the maximum speed,
and if you wish, the spin cycle can be
cancelled.
If the label does not indicate
specifi c information, it is possible to
use the maximum spin expected in the
program.
To prevent damage to the fabrics, it
is not possible to increase the speed
over the maximum allowed for the
programme.
To reactivate the spin cycle press
the button until you reach the spin
speed you would like to set.
It is possible to modify the spin
speed without pausing the machine.
KEY LOCK
Pressing simultaneously the
buttons TEMPERATURE SELECTION
and SPIN SPEED for about 3 seconds,
the machine allows you to lock the
keys. In this way, you can avoid making
accidental or unwanted changes if
a button on the display is pressed
accidently during a cycle.
The key lock can be simply
cancelled by pressing the two buttons
simultaneously again or turning off the
appliance.
Digital Display
The display’s indicator system allows
you to be constantly informed about the
status of the machine.
1) OPTIONS INDICATOR LIGHTS
The indicator lights show the
options that can be selected by the
relevant button.
2) CYCLE DURATION
When a programme is selected
the display automatically shows
the cycle duration, which can vary,
depending on the options selected.
During the initial fi lling phase
of the cycle the machine calculates the
actual cycle time needed based on the
load size, content and options selected.
The real time of the wash will then be
displayed. This time can recaulculate
17
ENGLISH TECHNICAL PASSPORT
Washing Machines
during the wash depending on
detergent levels and load balancing.
3) DOOR LOCKED INDICATOR
LIGHT
The indicator light is illuminated
when the door is fully closed.
Close the door BEFORE selecting the
START/PAUSE button.
When START/PAUSE is pressed
on the machine with the door closed,
the indicator will fl ash momentarily and
then illuminate.
If the door is not properly closed, the
light will continue to fl ash for about 7
seconds, after which the start command
will be automatically cancelled. In this
case, close the door in the proper way
and press the START/PAUSE button.
A special safety device
prevents the door from being opened
immediately after the end of the cycle.
Wait for 2 minutes after the wash cycle
has fi nished and the DOOR LOCKED
light has gone out before opening the
door. At the end of the cycle turn the
programme selector to OFF.
4) Kg LOAD INDICATOR LIGHT (function
active only on Cotton and Synthetics
programmes)
During the fi rst minutes of the
cycle, the «Kg LOAD» indicator will
remain on while the intelligent sensor
will weigh the laundry and adjust
the cycle time, water and electricity
consumption accordingly.
Through every wash phase «Kg
LOAD” allows to monitor information on
the wash load in the drum and in the
fi rst minutes of the wash it:
adjusts the amount of water
required;
determines the length of the
wash cycle;
controls rinsing according to
the type of fabric selected to be washed
it;
adjusts the rhythm of drum
rotation for the type of fabric being
washed;
recognises the presence of
too much soap suds, and if necessary,
adjust the amount of rinse water.
adjusts the spin speed
according to the load, thus avoiding any
imbalance.
5) KEY LOCK INDICATOR LIGHT
The indicator light show that the
keys are locked.
6) WASH TEMPERATURE
INDICATOR LIGHTS
This show the washing temperature
of the selected programme that can
be changed (where allowed) by the
relevant button.
If you want carry out a cold wash all
the indicators must be off.
7) SPIN SPEED INDICATOR
LIGHTS
This show the spin speed of the
selected programme, you can reduce or
omit by the relevant button.
18
TECHNICAL PASSPORT ENGLISH
Washing Machines
Table of programmes
PROGRAMME
(see control panel)
(MAX.)
6
kg
7
kg
8
kg
9
kg
2
1
Whites
2)
6 7 8 9 75° • •
Cotton +
2)
Prewash
6 7 8 9 60° • • •
**
Cotton 2)
6 7 8 9 60° • •
Eco 20° 6 7 8 9 20° • •
Mixed
2)
3 3,5 4 4,5 60° • •
Delicates 2 2,5 2,5 2,5 40° • •
Rinse - - - - - •
Spin - - - - -
Drain - - - - -
14'
Rapid
3)
30’
14’-30’-44’
44'
1 1 1,5 1,5 30° • •
2 2,5 2,5 2,5 20° • •
3 3,5 3,5 3,5 40° • •
Dark Colours 3 3,5 4 4,5 40° • •
Shirts
2)
3 3,5 4 4,5 30° • •
Silk 1 1 2 2 30° • •
Wool 1 1 2 2 40° • •
Handwash 1 1 2 2 40° • •
19
ENGLISH TECHNICAL PASSPORT
Washing Machines
Please read these notes:
* Maximum load capacity of dry clothes,
according to the model used (see
control panel).
1) When a programme is selected, on
the display is shown the display shows
the recommended wash temperature
that can be reduced (where allowed) by
the relevant button.
2) For the programmes shown you
can adjust the duration and intensity of
the wash using the STAIN LEVEL button.
3) Selecting the RAPID program on
the knob, it will be possible to select
with the RAPID button, one of the
three rapid programs available among
14’, 30’ and 44’.
** STANDARD COTTON PROGRAMMES
ACCORDING TO (EU) No 1015/1010 and
No 1061/1010.
COTTON PROGRAMME WITH A
TEMPERATURE OF 50°C.
COTTON PROGRAMME WITH A
TEMPERATURE OF 40°C.
These programmes are suitable to
clean normally soiled cotton laundry and
they are the most effi cient programmes
in terms of combined energy and water
consumptions for washing cotton
laundry.
These programmes have been
developed to be compliant with the
temperature on the wash label on
the garments and the actual water
temperature may slightly differ from
the declared temperature of the cycle.
Programmes selection
To clean different types of fabrics
and various levels of dirt, the washing
machine has specifi c programs to meet
every need of washing (see table of
programmes).
Whites
An intensive wash. The fi nal spin at
maximum speed gives more effi cient
removal.
Cotton + Prewash
This programme has been designed
to remove the stronger stains from
cotton white clothes. The prewash
guarantees the tough dirt removal.
Add into compartment «1» a quantity
of detergent equal to 20% of that used
for main wash.
Cotton
This program is suitable to clean
normally soiled cotton laundry and
it is the most effi cient program in
terms of combined energy and water
consumptions for washing cotton
laundry.
Eco 20°
This innovative programme, allows
you to wash different fabrics and
colours together, such as cottons,
synthetics and mixed fabrics at
only 20°C and provides an excellent
cleaning performance. Consumption
on this program is about 40% of a
conventional 40°C. cottons wash.
20
TECHNICAL PASSPORT ENGLISH
Washing Machines
Mixed
The washing and rinsing optimise
the speed and rhythm of the drum
action and water levels. The gentle
spin, ensures a reduced formation of
creases in the fabric.
Delicates
This program has reduced periods
of drum rotation during the cycle and
is particularly suitable or washing
delicate fabrics. The wash cycle and
rinses are carried out with a high
level of water to ensure the best
performance.
Rinse
This program performs 3 rinses
with an intermediate spin (which
can be reduced or excluded by using
the appropriate button). It is used for
rinsing any type of fabric, for example
after a wash carried out by hand.
Spin
The programme carries out a
maximum spin. It is possible to delete
or reduce the spin with the SPIN
SPEED button.
Drain
This programme drains out the
water.
Rapid (14’-30’-44’)
Washing cycle suggested for low
loads and slightly dirty. With this
program it is recommended to reduce
the quantity of detergent normally
used, in order to avoid unnecessary
waste. Selecting the RAPID program
and acting on the button you can
choose one of three programs
available.
Dark Colours
Program designed to mix all dark
garments and to avoid the loss of
colour and the formation of creases.
We recommend the use of liquid
detergent.
Shirts
The washing cycle is optimized to
reduce the creation of creases, keeping
an excellent washing performance. It
is also possible to further reduce the
spin speed, to ensure an easier ironing.
Silk
Dedicated program for silk fabrics
that can be wash with a washing
machine washable. The rotations of
the drum are delicate, the temperature
does not exceed 30°C and the program
ends with a gentle spin.
Wool
This program performs a wash cycle
dedicated to the wool fabrics that can
be washed in a washing machine, or
the articles to be washed by hand.
Handwash
Program for hand wash only clothes,
the program ends with 3 rinses and a
slow spin.
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/