Pioneer SPH-DA01 Инструкция по установке

Installation Manual

Manuel d’installation

Руководство по установке

SPH-DA01

AppRadio

English NederlandsDeutschEspañolItalianoFrançais Русский

Precautions

Your new display unit and this manual 3

Important safeguards 3

Connecting the system

Precautions before connecting the

system 4

Before installing this product 4

To prevent damage 5

– Notice for the blue/white lead 5

Parts supplied 6

Connecting the system 7

Connecting the power cord 8

Connecting the control line cable 10

When connecting to separately sold power

amp 11

When connecting to separately sold

subwoofer 12

When connecting a rear view camera 13

Installation

Precautions before installation 14

To avoid electromagnetic interference 14

Before installing 14

Installing this product 15

– Installation notes 15

– Parts supplied 16

– Before installing this product 16

– Installation with the holder and side

bracket 17

– Installation using the screw holes on

the side of this product 17

Installing the GPS aerial 18

– Installation notes 18

– Parts supplied 18

– When installing the aerial inside the

vehicle (on the dashboard or rear

shelf) 19

Installing the microphone 20

– Parts supplied 20

– Mounting on the sun visor 20

– Installation on the steering column 20

After installation

After installing this product 22

Contents

Engb

2

Your new display unit and

this manual

! Do not operate this product, any applica-

tions, or the rear view camera option (if pur-

chased) if doing so will divert your attention

in any way from the safe operation of your

vehicle. Always observe safe driving rules

and follow all existing traffic regulations. If

you experience difficulty in operating this

product or reading the display, park your

vehicle in a safe location and apply the

handbrake before making the necessary

adjustments.

! Do not install this product where it may (i)

obstruct the driver’s vision, (ii) impair the

performance of any of the vehicle’s operat-

ing systems of safety features, including

airbags, hazard lamp buttons, or (iii) impair

the driver’s ability to safely operate the vehi-

cle. In some cases, it may not be possible

to install this product because of the vehi-

cle type or the shape of the vehicle interior.

! This manual explains how to install this

product in your vehicle. Operation of this

product is explained in the separate man-

uals.

Important safeguards

WARNING

Pioneer does not recommend that you install

this product yourself. We recommend that

only authorised Pioneer service personnel,

who have special training and experience in

mobile electronics, set up and install this

product. NEVER SERVICE THIS PRODUCT

YOURSELF. Installing or servicing this pro-

duct and its connecting cables may expose

you to the risk of electric shock or other ha-

zards, and can cause damage to the product

that is not covered by warranty.

! Read this manual fully and carefully before

installing this product.

! Keep this manual handy for future refer-

ence.

! Pay close attention to all warnings in this

manual and follow the instructions care-

fully.

! Traffic restrictions and advisories are al-

ways more important than guidance given

by a third-party navigation/mapping iPhone

application. Always obey current traffic re-

strictions, even if the application provides

contrary advice.

! As with any accessory in your vehicle’s in-

terior, this product should not divert your

attention from the safe operation of your

vehicle. If you experience difficulty in oper-

ating this product or reading the display,

please make adjustments while safely

parked.

! Please remember to wear your seat belt at

all times while operating your vehicle. If

you are in an accident, your injuries can be

considerably more severe if your seat belt

is not properly fastened.

! Certain country and government laws may

prohibit or restrict the placement and use

of this product in your vehicle. Please com-

ply with all applicable laws and regulations

regarding the use, installation and opera-

tion of this product.

Engb

3

English

Section

01

Precautions

Precautions before

connecting the system

CAUTION

! If you decide to perform the installation

yourself, and have special training and ex-

perience in the mobile electronics instal-

lations, please carefully follow all of the

steps in the installation manual.

! Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wir-

ing to remain exposed.

! Do not directly connect the yellow lead of

this product to the vehicle battery. If the

lead is directly connected to the battery,

engine vibration may eventually cause

the insulation to fail at the point where

the wire passes from the passenger com-

partment into the engine compartment. If

the yellow lead’s insulation tears as a re-

sult of contact with metal parts, short-cir-

cuiting can occur, resulting in

considerable danger.

! It is extremely dangerous to allow cables

to become wound around the steering col-

umn or gearstick. Be sure to install this

product, its cables, and wiring away in

such so that they will not obstruct or hin-

der driving.

! Make sure that the cables and wires will

not interfere with or become caught in

any of the vehicle’s moving parts, espe-

cially the steering wheel, gearstick, hand-

brake, sliding seat tracks, doors, or any of

the vehicle’s controls.

! Do not route wires where they will be ex-

posed to high temperatures. If the insula-

tion heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

! Do not cut the GPS aerial cable to shorten

it or use an extension to make it longer.

Altering the aerial cable could result in a

short circuit or malfunction.

! Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse resis-

tor or filter, etc.) may fail to work properly.

! Never feed power to other electronic pro-

ducts by cutting the insulation of the

power supply lead of this product and tap-

ping into the lead. The current capacity of

the lead will be exceeded, causing over-

heating.

Before installing this product

! Use this unit with a 12-volt battery and ne-

gative earthing only. Failure to do so may

result in a fire or malfunction.

! To avoid shorts in the electrical system, be

sure to disconnect the (–) battery cable be-

fore installation.

Engb

4

Section

02

Connecting the system

To prevent damage

WARNING

! Use speakers over 50 W (output value)

and between 4 W to 8 W (impedance value).

Do not use 1 W to 3 W speakers for this

unit.

! The black lead is earth. Please earth this

lead separately from the earth of high-cur-

rent products such as power amps. Do not

earth more than one product together

with the earth from another product. For

example, you must separately earth any

amp unit away from the earth of this pro-

duct. Connecting earths together can

cause a fire and/or damage the products if

their earths became detached.

! When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

! When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

! This product cannot be installed in a vehi-

cle without ACC (accessory) position on

the ignition switch.

A

C

O

N

S

T

A

R

T

O

F

O

N

S

T

A

R

T

O

F

ACC position No ACC position

! To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe-

cially important to insulate all unused

speaker leads, which if left uncovered may

cause a short circuit.

! Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

! Since a unique BPTL circuit is employed,

do not directly earth the * side of the

speaker lead or connect the * side of an-

other side of the speaker lead together. Be

sure to connect the * side of the speaker

lead to the * side of the speaker lead on

this product.

! If the RCA pin jack on this product will not

be used, do not remove the caps attached

to the end of the connector.

Notice for the blue/white lead

! When the ignition switch is turned on (ACC

ON), a control signal is output through the

blue/white lead. Connect to an external

power amp’s system remote control term-

inal (max. 300 mA 12 V DC). The control sig-

nal is output through the blue/white lead,

even if the AV source is switched off.

! Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive

current drain and malfunction.

! Be sure not to use this lead as the power

supply lead for the auto-aerial or aerial

booster. Such connection could cause ex-

cessive current drain and malfunction.

Engb

5

English

Section

02

Connecting the system

Parts supplied

This product Power cord

Output cable Control line cable

GPS aerial iPhone cable

Microphone

Engb

6

Section

02

Connecting the system

WARNING

· To avoid the risk of accident and the potential violation of applicable laws, this product should never

be used while the vehicle is being driven except for navigation purposes.

· In some countries, the viewing of images on a display inside a vehicle even by persons other than the

driver may be illegal. Where such regulations apply they must be obeyed and this product’s

App-based content should not be used.

(*2)

For details concerning

operations and

compatibility, refer to

Important Information

for Users.

Aerial jack

(RADIO ANT)

Microphone

3 m

GPS aerial

Vehicle aerial

4 m

iPhone cable

iPhone or iPod touch (*2)

This product

Control line cable

Wired remote input (SWC)

Please refer to the instruction manual for

the Hard-wired remote control adaptor

(sold separately).

Microphone jack

(MIC)

Output cable

(*1)

Make sure that the three yellow, green and blue connectors are attached before connecting the system.

2 m

25 cm

8.5 cm

Engb

7

English

Section

02

Connecting the system

Connecting the power cord

ISO connector

Orange/white (ILLUMI)

To lighting switch terminal.

Black (GND)

To vehicle (metal) body.

In some vehicles, the ISO connector may be divided

into two. In this case, be sure to connect to both

connectors.

Note

Yellow (*2)

Back-up

(or accessory)

Red (*4)

Accessory

(or back-up)

Yellow (*1)

To terminal supplied with power

regardless of ignition switch position.

Red (*3)

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF.

Connect leads of the

same colour to each other.

*2

*4

*3

*5

Depending on the types of vehicles, the

function of *3 and *5 may be different. In this

case, be sure to connect *2 to *5 and *4 to *3

as shown in the figure.

Note

Blue/white (P.CONT)

To P.CONT of control line cable.

*1

Cap (*1)

When not using this terminal, do

not remove the cap.

Engb

8

Section

02

Connecting the system

This product

Notes

· When a subwoofer (*6) is connected to this

product instead of a rear speaker, change the

rear output setting in the initial setting. (Refer to

Operation Manual.) The subwoofer output of this

product is monaural.

· When using a subwoofer of 70 W (2 Ω), be sure

to connect with violet and violet/black leads of

this product. Do not connect anything with

green and green/black leads.

Fuse (15 A)

Speaker leads

White: Front left 

White/black: Front left 

Grey: Front right 

Grey/black: Front right 

Green: Rear left or Subwoofer  (*6)

Green/black: Rear left or Subwoofer  (*6)

Violet: Rear right or Subwoofer  (*6)

Violet/black: Rear right or Subwoofer  (*6)

Power cord

Engb

9

English

Section

02

Connecting the system

Connecting the control line cable

Control line cable

Pink (REVERSE)

This is connected so that the this product can detect

whether the vehicle is moving forwards or

backwards. Connect the pink lead to the lead whose

voltage changes when the reverse gear is engaged.

Unless connected, the sensor may not detect your

vehicle travelling forward/backward properly, and

thus the position of your vehicle detected by the

sensor may be misaligned from the actual position.

GREEN/WHITE LEAD AT POWER CONNECTOR IS

DESIGNED TO DETECT PARKED STATUS AND MUST

BE CONNECTED TO THE POWER SUPPLY SIDE OF THE

HANDBRAKE SWITCH. IMPROPER CONNECTION OR

USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW

AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.

When you use a rear view camera, please make

sure to connect this lead. Otherwise you cannot

switch to the rear view camera picture.

Power supply side

Earth side

Handbrake switch

This product

Connection method

Clamp the lead of the power supply

side of the handbrake switch.

Clamp firmly with needle-nosed

pliers.

WARNING

Note

Green/white (BRAKE)

Used to detect the ON/OFF status of the

handbrake. This lead must be connected to the

power supply side of the handbrake switch.

If this connection is made incorrectly or

omitted, certain functions of this product

will be unusable.

The position of the handbrake switch vary

depending on the vehicle model. For details,

consult your authorised Pioneer dealer or an

installation professional.

Note

Engb

10

Section

02

Connecting the system

When connecting to separately sold power amp

This product

To system control terminal of the power amp

(max. 300 mA 12 V DC).

Blue/white (P.CONT)









Left Right

Power amp

(sold separately)

Rear speaker Rear speaker

Control line cable

Output cable

Power cord

Blue/white (P.CONT)

RCA cable

(sold separately)

White

(FULL/SW)

Red

(FULL/SW)

Engb

11

English

Section

02

Connecting the system

When connecting to separately sold subwoofer

This product

To system control terminal of the power amp

(max. 300 mA 12 V DC).

Blue/white (P.CONT)

White

(FULL/SW)

Red

(FULL/SW)









Power amp

(sold separately)

Subwoofer

Control line cable

Output cable

Power cord

Blue/white (P.CONT)

RCA cable

(sold separately)

You can change the RCA output of the subwoofer

depending on your subwoofer system.

(Refer to Operation Manual.)

Note

Engb

12

Section

02

Connecting the system

When connecting a rear

view camera

When this product is used with a rear view

camera, it is possible to automatically switch

from the video to rear view image when the

gearstick is moved to REVERSE (R). Rear

Camera mode also allows you to check what

is behind you while driving.

WARNING

When you connect the rear view camera, do not

forget to adjust the setting of this product so as

to display mirror reversed images on the screen.

CAUTION

! The rear view camera is used as an aid to

keep an eye on trailers, or backing into a tight

parking spot. Do not use this function for en-

tertainment purposes.

! Objects in rear view may appear closer or

more distant than in reality.

! Please note that the image area shown by the

rear view camera may differ slightly when full-

screen images are displayed when backing

and when checking the rear of the vehicle

while moving forward.

(REVERSE)

Pink

Control line cable

Yellow

(CAMERA VIDEO)

This product

(e.g. ND-BC4)

(sold separately)

RCA cable

Rear view camera

For more details about the wiring, refer to Connecting

the control line cable on page 10.

Notes

! To display the rear view camera image, set

the rear view camera to on.

! Connect this product to the rear view cam-

era only. Do not connect to any other equip-

ment.

Engb

13

English

Section

02

Connecting the system

Precautions before

installation

CAUTION

! Never install this product in places where,

or in a manner that:

— Could injure the driver or passengers if

the vehicle stops suddenly.

— May interfere with the driver’s opera-

tion of the vehicle, such as on the floor

in front of the driver’s seat, or close to

the steering wheel or gearstick.

! Make sure there is nothing behind the

dashboard or panelling when drilling

holes in them. Be careful not to damage

fuel lines, brake lines, electronic compo-

nents, communication wires or power

cables.

! When using screws, do not allow them to

come into contact with any electrical lead.

Vibration may damage wires or insulation,

leading to a short circuit or other damage

to the vehicle.

! To ensure proper installation, be sure to

use the supplied parts in the manner spe-

cified. If any parts are not supplied with

this product, use compatible parts in the

manner specified after you have the parts’

compatibility checked by your dealer. If

parts other than supplied or compatible

ones are used, they may damage internal

parts of this product or they may work

loose and the product may become de-

tached.

! It is extremely dangerous to allow cables

to become wound around the steering col-

umn or gearstick. Be sure to install this

product, its cables, and wiring away in

such so that they will not obstruct or hin-

der driving.

! Make sure that leads cannot get caught in

a door or the sliding mechanism of a seat,

resulting in a short circuit.

! Please confirm the proper function of

your vehicle’s other equipment after in-

stallation of this product.

! Do not install this product where it may (i)

obstruct the driver’s vision, (ii) impair the

performance of any of the vehicle’s oper-

ating systems or safety features, includ-

ing airbags, hazard lamp buttons or (iii)

impair the driver’s ability to safely oper-

ate the vehicle.

! Install this product between the driver’s

seat and front passenger seat so that it

will not be hit by the driver or passenger if

the vehicle stops quickly.

! Never install this product in front of or

next to the place in the dashboard, door,

or pillar from which one of your vehicle’s

airbags would deploy. Please refer to your

vehicle’s owner’s manual for reference to

the deployment area of the frontal air-

bags.

To avoid electromagnetic

interference

In order to prevent interference, set the follow-

ing items as far as possible from this product,

other cables or leads:

! FM, MW/LW aerial and its lead

! GPS aerial and its lead

In addition, you should lay or route each aerial

lead as far as possible from other aerial leads.

Do not bind, lay or route them together, or

cross them. Electromagnetic noise will in-

crease the potential for errors in the vehicle’s

location display.

Before installing

! Consult with your nearest dealer if installa-

tion requires drilling holes or other modifi-

cations of the vehicle.

! Before making a final installation of this

product, temporarily connect the wiring to

confirm that the connections are correct

and the system works properly.

Engb

14

Section

03

Installation

Installing this product

Installation notes

! Do not install this product in places subject

to high temperatures or humidity, such as:

— Places close to a heater, vent or air con-

ditioner.

— Places exposed to direct sunlight, such

as on top of the dashboard.

— Places that may be exposed to rain,

such as close to the door or on the vehi-

cle’s floor.

! Install this product in an area strong en-

ough to bear its weight. Choose a position

where this product can be firmly installed,

and install it securely. If this product is not

securely installed, the current location of

the vehicle cannot be displayed correctly.

! Install this product horizontally on a sur-

face within 0 to 60 degrees tolerance. Im-

proper installation of the unit with the

surface tilted more than these tolerances

increases the potential for errors in the ve-

hicle’s location display, and might other-

wise cause reduced display performance.

60°

! When installing, to ensure proper heat dis-

persal when using this unit, make sure you

leave ample space behind the rear panel

and wrap any loose cables so they are not

blocking the vents.

Leave ample

space

5 cm

Engb

15

English

Section

03

Installation

Parts supplied

Parts marked (*) are pre-installed.

The display unit Holder*

Side bracket*

(2 pcs.)

Truss head screw

(5 mm × 6 mm)

(8 pcs.)

Flush surface screw

(5 mm × 7 mm)

(4 pcs.)

Screw*

(2.6 mm × 5 mm)

(4 pcs.)

Screw for fixing the

side bracket*

(5 mm × 7 mm)

(4 pcs.)

Double-ended screw

Rubber bush Trim ring

Before installing this product

% Remove the holder.

Loosen the screws (2.6 mm × 5 mm) to re-

move the holder.

Holder

Screw (2.6 mm × 5 mm)

Engb

16

Section

03

Installation

Installation with the holder

and side bracket

1 Install the holder into the dashboard.

After inserting the holder into the dashboard,

select and bend the tabs appropriate to the

thickness of the dashboard material. (Install

this product as firmly as possible using the

top and bottom tabs. To secure this product,

bend the tabs 90 degrees.)

Dashboard

Holder

2 Install this product and fasten the

screws.

Rubber bush Dashboard

Double-ended screw Screw (2.6 mm × 5 mm)

3 Attach the trim ring.

Trim ring

Installation using the screw

holes on the side of this product

1 Remove the side brackets.

Side bracket

Screw for fixing the side bracket

(5 mm × 7 mm)

2 Fastening the unit to the factory radio-

mounting bracket.

Position this product so that its screw holes

are aligned with the screw holes of the brack-

et, and tighten the screws at three or four loca-

tions on each side.

Use either the truss head screws (5 mm ×

6 mm) or flush surface screws (5 mm ×

7 mm), depending on the shape of the brack-

et’s screw holes.

Engb

17

English

Section

03

Installation

If the tab interferes with installation,

you may bend it down out of the way.

Dashboard or console

T

russ head screw

or flush surface

screw

Be sure to use the

screws supplied

with this product.

Factory radio-mounting bracket

Installing the GPS aerial

CAUTION

Do not cut the GPS aerial lead to shorten it

or use an extension to make it longer. Alter-

ing the aerial cable could result in a short cir-

cuit or malfunction and permanent damage

to this product.

Installation notes

! The aerial should be installed on a level sur-

face where radio waves will be blocked as

little as possible. Radio waves cannot be re-

ceived by the aerial if reception from the sa-

tellite is blocked.

Dashboard Rear shelf

! Take care not to pull the aerial lead when

removing the GPS aerial. The magnet at-

tached to the aerial is very powerful, and

the lead may become detached.

! Do not paint the GPS aerial, as this may af-

fect its performance.

Parts supplied

GPS aerial Double-sided tape

Engb

18

Section

03

Installation

When installing the aerial inside the vehicle (on the dashboard or

rear shelf)

WARNING

Do not install the GPS aerial over any sensors or vents on the dashboard of the vehicle, as

doing so may interfere with the proper functioning of such sensors or vents and may compro-

mise the ability of the double-sided tape under the GPS aerial to properly and securely affix to

the dashboard.

Affix the double-sided tape on the surface as

level as possible where the GPS aerial faces

the window. Place the GPS aerial on the dou-

ble-sided tape.

The double-sided tape

contains a strong adhesive

which may leave a mark on

the surface if it is removed.

Note

Clamps

Use separately sold clamps

to secure the lead where necessary

inside the vehicle.

GPS aerial

Double-sided tape

Peel off the protective sheet.

Make sure the surface is free of

moisture, dust, grime, oil, etc.,

before affixing the double-sided

tape.

Note

Some models use window glass that does not

allow signals from GPS satellites to pass

through. On such models, install the GPS aer-

ial on the outside of the vehicle.

Engb

19

English

Section

03

Installation

Installing the microphone

! Install the microphone in a place where its

direction and distance from the driver

make it easiest to pick up the driver’s voice.

! Be sure to turn off (ACC OFF) the product

before connecting the microphone.

Parts supplied

Microphone Microphone holder

Mounting on the sun visor

% Attach the microphone clip to the sun

visor.

Microphone clip

Clamps

Use separately sold clamps to secure the lead

where necessar y inside the vehicle.

Install the microphone on the sun visor when

it is in the up position. It cannot recognise the

driver’s voice if the sun visor is in the down po-

sition.

Installation on the steering column

1 Unclip the microphone and place it into

the microphone holder.

Microphone

Microphone holder

2 Mount the microphone on the steering

column.

Peel the backing from the double-sided tape

on the back of the microphone holder and at-

tach the holder to the steering column.

Install the microphone on the

steering column, keeping it away

from the steering wheel.

Engb

20

Section

03

Installation

Страница загружается ...

Pioneer SPH-DA01 Инструкция по установке

Pioneer SPH-DA01 Инструкция по установке

на других языках

Похожие модели бренда

Модели других брендов