SICK SLT Smart Light Tower Инструкция по эксплуатации

O P E R A T I N G I N S T R U C T I O N S

SLT

Smart Light Tower

O P E R A T I N G I N S T R U C T I O N S

SLT

Smart Light Tower

de

en

es

fr

it

ja

pt

ru

zh

Described product

SLT - Smart Light Tower

Manufacturer

SICK AG

Erwin-Sick-Str. 1

79183 Waldkirch

Germany

Legal information

This work is protected by copyright. Any rights derived from the copyright shall be

reserved for SICK AG. Reproduction of this document or parts of this document is

only permissible within the limits of the legal determination of Copyright Law. Any modi‐

fication, abridgment or translation of this document is prohibited without the express

written permission of SICK AG.

The trademarks stated in this document are the property of their respective owner.

Original document

This document is an original document of SICK AG.

2006/42/EC

NO

SAFETY

8026183 / 2021-04-29 | SICK

Subject to change without notice

3

Contents

1 General safety notes......................................................................... 5

2 Notes on UL approval........................................................................ 5

2.1 UL Satisfaction Ratings............................................................................ 5

3 Intended use...................................................................................... 5

4 Product description........................................................................... 6

4.1 Product characteristics............................................................................ 6

5 Operating elements and status indicators.................................... 6

6 Mounting............................................................................................. 7

6.1 Scope of delivery....................................................................................... 7

6.2 Mounting requirements............................................................................ 7

6.3 Notes on mounting................................................................................... 7

6.4 Mounting on the machine housing.......................................................... 7

6.5 Mounting on a rod.................................................................................... 8

6.6 Mounting the Smart Light Buzzer SLB.................................................... 8

7 Electrical installation........................................................................ 9

7.1 Attaching connection cable...................................................................... 10

8 Operation............................................................................................ 11

8.1 Operating modes...................................................................................... 11

8.2 Configuration............................................................................................. 12

9 Troubleshooting................................................................................. 19

10 Disassembly and disposal............................................................... 19

11 Maintenance...................................................................................... 19

12 Technical data.................................................................................... 20

12.1 Technical specifications........................................................................... 20

12.2 Dimensional drawings.............................................................................. 20

13 Annex.................................................................................................. 21

CONTENTS

4

8026183 / 2021-04-29 | SICK

Subject to change without notice

1 General safety notes

■

Read these operating instructions before commissioning the device.

■

Connection, mounting and configuration of the device must only be carried

out by qualified personnel.

■

2006/42/EC

NO

SAFETY

This device does not constitute a safety component as defined in the

Machinery Directive.

■

Do not install the device in places exposed to direct UV radiation (sunlight)

or other weather conditions unless this is expressly permitted in the operating

instructions.

■

When commissioning the device, ensure adequate protection against moisture

and contamination.

■

These operating instructions contain information required during the life cycle of

the device.

2 Notes on UL approval

2.1 UL Satisfaction Ratings

The Smart Light Tower is a UL Recognized Component (file no. E198242).

Standard for safety:

•

UL 508, Standard for Industrial Control Equipment

•

CSA C22.2 No. 14-18, Standard for Industrial Control Equipment

The following compliance requirements of UL certification must be considered:

•

A class 2 voltage supply unit must be used for the voltage supply

3 Intended use

The Smart Light Tower SLT is used for the visual display of machine states or to indicate

filling levels.

The optional Smart Light Buzzer SLB unit is used for acoustic alarms.

Both the 20 LED segments and the acoustic Smart Light Buzzer SLB can be switched

on and off individually. Parameterization for this is done via the IO-Link interface.

Intended use requires that the device is used industrially indoors without any specific

climatic and atmospheric requirements. Any use outside of the areas mentioned in

each case will be considered to be incorrect use and void any warranty claims against

SICK AG. The intended use is only guaranteed if the housing is completely mounted.

In the event of any other usage or modification to the device (e.g., due to opening the

housing during mounting and electrical installation) or changes to the SICK software,

any claims against SICK AG under the warranty will be rendered void.

GENERAL SAFETY NOTES 1

8026183 / 2021-04-29 | SICK

Subject to change without notice

5

4 Product description

4.1 Product characteristics

The Smart Light Tower SLT is a signal lamp used for the visual display of, for example,

machine states or to indicate filling levels. With the Smart Light Buzzer SLB unit, the

device is also suitable for issuing acoustic alarms if needed.

The Smart Light Tower is an IO-Link device that communicates exclusively via the IO-

Link protocol with the higher-level IO-Link master assembly. The IO-Link communication

interface enables direct access to process data and parameter values. The required

IODD can be found at http://www.sick.com/slt.

The device has 20 LED segments. According to IO-Link standards, these LED segments

and the optional buzzer unit can be configured and operated individually. It is possible

to change device parameters during operation. Configuration is performed either via

the SICK SOPAS ET software (available free of charge at www.sick.com) or directly via

the PLC interface.

Further specifications can be found in the technical data (see "Technical data",

page 20).

5 Operating elements and status indicators

1

4

5

6

7

2

3

8

9

ß

à

1

Cover

2

Main body

3

20 LED segment display

4

IO-Link status LED

5

Positionsmarkierung

6

Base

7

Waterproof foil

8

Fastening nut (M30)

9

Summereinheit (Optional)

ß

M12 connection (IO-Link)

à

½ inch thread

Display Description

Green LED lights up Device switched on

4 PRODUCT DESCRIPTION

6

8026183 / 2021-04-29 | SICK

Subject to change without notice

Display Description

Green LED flashes IO-Link connection active

off - Device not ready

- No voltage

- Voltage below the limit values

6 Mounting

6.1 Scope of delivery

•

SLT

•

Quickstart

6.2 Mounting requirements

•

For the typical space requirements for the device, see the type-specific dimen‐

sional drawing, see "Technical data", page 20.

•

Comply with technical data, such as the permitted ambient conditions for opera‐

tion of the device (e.g., temperature range, EMC interference emissions, ground

potential).

•

To prevent condensation, avoid exposing the device to rapid changes in tempera‐

ture.

•

Protect the device from direct sunlight.

•

Only mount the device using the threaded mounting holes provided.

•

Shock and vibration resistant mounting.

6.3 Notes on mounting

The following requirements are necessary for proper installation:

•

Switch off the voltage supply before you mount or replace the devices.

•

Do not apply excessive force when mounting/dismounting the signal lamp and

buzzer unit.

•

Perform installation on a rugged, level surface.

•

Install this device where there is no excessive vibration.

Note the maximum permissible tightening torque for the device of 4.5 Nm.

NOTE

•

This product comes with a waterproof foil on the bottom of the bracket (1 mm).

This must be used during installation. We recommend, however, applying sealant

between the device and the installation surface to guarantee the watertightness

of the device if there are any irregularities present in the installation surface.

•

If sealing from the nut side (interior of the machine) is required, apply a suitable

sealing compound for the M30 nut to the

1

/

2

-inch NPT thread.

6.4

Mounting on the machine housing

Unscrew the M30 nut on the bottom of the signal lamp. Insert the bottom part of the

signal lamp through the mounting surface and secure the lamp to the machine using

the M30 nut and 4.5 Nm tightening torque.

Attachment of the connection cable is described in "Electrical installation", page 9.

MOUNTING 6

8026183 / 2021-04-29 | SICK

Subject to change without notice

7

1

2

3

1

Mounting surface

2

Ø 31 mm

3

M30 Nut

6.5 Mounting on a rod

Screw a rod with ½-inch NPT onto the female thread of the signal lamp. The recom‐

mended tightening torque is 2.25 Nm.

1

6.6 Mounting the Smart Light Buzzer SLB

NOTE

The SLB (SLB060-0B010K700) is available as an optional accessory (part number

6076072).

6 MOUNTING

8

8026183 / 2021-04-29 | SICK

Subject to change without notice

1.

To unlock it, rotate the cover (1) on the top of the signal lamp in the counterclock‐

wise direction. Lift up the released cover. Note the position markings (2 Locked;

3 Unlocked).

2 3

1

2.

Locate the Smart Light Buzzer (1) on the signal lamp with the position markers as

shown. To lock the buzzer unit and signal lamp together, turn the signal lamp in the

clockwise direction. (2 Unlocked; 3 Locked).

2 3

1

7 Electrical installation

No separate supply voltage connection is required for the SLT. The supply is provided by

the higher-level IO-Link master via the IO-Link interface.

The signal lamp must be connected in a voltage-free state.

U

B

: 18... 30 V DC, see "Technical data", page 20

Table 1: IO-Link port, M12, A-coded, port class A

SLT Signal Description

1 + (L+) +24 V DC

2 n.c. -

3 L- 0 V (logic ground)

4 C/Q IO-Link

5 n.c. -

3

4

2

1

5

ELECTRICAL INSTALLATION 7

8026183 / 2021-04-29 | SICK

Subject to change without notice

9

7.1 Attaching connection cable

1.

Rotate the main body (1) in the counterclockwise direction to unlock it. Note the

position markings while doing so (2 Locked; 3 Unlocked). You can now remove

the main body from the base (4).

2 3

1

4

2.

Now connect the connecting cable (2) to the M12 port (1) on the main body. (3

min. internal diameter)

1

2

3

Ø 17 (0.67)

3. Locate the main body in the base bracket again and rotate the main body in

the clockwise direction to secure the signal lamp. Pay attention to the position

markers while doing so. (1 Unlocked; 2 Locked)

1 2

7

ELECTRICAL INSTALLATION

10

8026183 / 2021-04-29 | SICK

Subject to change without notice

8 Operation

8.1 Operating modes

There are 3 different operating modes for the SLT, which are used to display various

warning and indicator signals:

•

Signal lamp mode

•

Filling level mode

•

Animation mode

8.1.1 Signal lamp mode

In Signal lamp mode, the SLT can be used as a standard signal lamp.

The 20 LED segments can be divided into a maximum of five groups. When evenly

distributed, four LEDs together always form a group. The number of LEDs per group

can be changed individually. Even if only one group is activated, all 20 LEDs are always

used for visualization. Exception: If the group separation function is activated, one row

of LEDs is switched off between the individual segments and the remaining number of

LEDs is reduced to 15.

The colors of the different groups can be selected from a color palette with eight

predefined colors. In addition, another individual color from a total of 21 predefined

colors can be added to the color palette here.

In Signal lamp mode, the LEDs can be set as either continuous light, flashing light,

strobe light, or pulsating light. The light animation frequency can be set individually.

8.1.2 Filling level mode

Filling level mode is used when the SLT is used as a level indicator or filling level display.

For this purpose, a level value is specified in the process data. The higher the level

value (in percent), the more LEDs are switched on at the signal lamp.

Each of the 20 LED segments can be individually colored from 21 predefined colors.

As in Signal lamp mode, each individual segment can be configured with a different

light pattern. Continuous light, flashing light, strobe light or pulsating light is available

for selection. The light animation frequency can be set individually.

Switching on the LEDs can be done either from the bottom end of the device upwards

or from the top end downwards. It is also possible for the segments to change color or

light pattern as soon as the segment above them begins to glow.

There are three options here:

•

The previously activated segments retain their light animation.

•

The segments that are already illuminated stop their light pattern animation as

soon as a new segment is added, but remain activated. Only the uppermost

segment shows an animation.

•

All segments show the light pattern of the uppermost segment to draw attention to

the current filling level, e.g. in the event of an overflow warning.

8.1.3 Animation mode

Animation mode is used to demonstrate the range of functions of the signal lamp. Here

the 20 different LED segments are switched on one after the other in a configured

sequence. In Animation mode, each LED segment of the SLT can be configured individ‐

ually.

OPERATION 8

8026183 / 2021-04-29 | SICK

Subject to change without notice

11

For coloring there are 21 predefined colors are available. In Animation mode, the LEDs

can be set as either continuous light, flashing light, strobe light, or pulsating light. The

light animation frequency can be set individually.

Switching on the LEDs can be done either from the bottom end of the device upwards

(bottom up) or from the top end downwards (top down). It is also possible for the

segments to change color or light pattern as soon as the segment above them begins to

glow.

There are three options here:

•

The previously activated segments retain their light animation.

•

The segments that are already illuminated stop their light pattern animation as

soon as a new segment is added, but remain activated. Only the uppermost

segment shows an animation.

•

All segments show the light pattern of the uppermost segment.

•

Other properties of the animation, e.g. loop/bounce effect, can also be set in this

mode.

8.2 Configuration

The SLT can be configured and controlled in three different ways:

1 Via SiLink2 IO-Link master and SOPAS ET with extensive graphical user interface

based on the SDD

2 Via IO-Link master (e.g. SIG200) and generic user interface based on the IODD

3 Via IO-Link master with direct access to the device parameters via IO-Link service

and process data (e.g. PLC with IO-Link master terminal)

8.2.1.1 Configuration via SiLink2 master and SOPAS ET

The SLT can be configured on a PC (running Microsoft Windows) using the SOPAS

Engineering Tool (SOPAS Et for short) software.

An IO-Link master is required for configuration and operation of the SLT. When using the

SiLink2 IO-Link master, a comprehensive graphical user interface is available to assist

during configuration. The required SiLink2 IO-Link master can be ordered separately.

The SOPAS Engineering Tool application can be downloaded at www.sick.com.

8.2.1.1.1 SDD installation

A SOPAS Device Description (SDD) is required in order to configure the SLT via graphic

user interface. Start SOPAS ET and install the SDD of the SLT as described in the

following section.

Adding SDD via the device catalog

Open the device catalog (1) and then the SDD installation menu using the gear (2)

icon:

1

2

Keep the default settings and select the SLT from the list of available SDDs after the

SDD search is complete. The SDD will now be installed, close the window when the

installation is complete.

8 OPERATION

12

8026183 / 2021-04-29 | SICK

Subject to change without notice

8.2.1.1.2 Establishing connection to the SLT

A connection between SOPAS ET and the SLT must now be established via SiLink2

master. The device search can be used for this purpose. Open the search settings

using the button in the lower right corner of the window. Select the interface-based

search and make sure that the “IO-Link communication” entry is selected in the

following window. If desired, the configured device search can be saved under

a user-defined name in the next step. SOPAS ET now searches for connected IO-

Link devices. After the search is finished, drag the found SLT to the project area:

SOPAS will now establish a connection to the SLT via IO-Link. You can identify a

successful connection by the green status display of the device tile in the project area:

Double-clicking on the device tile opens the graphical user interface for configuration

and control of the SLT, whose functions are explained in the following sections.

8.2.1.2 Overview of SOPAS ET and the standard functions on the individual pages

The pages for the SLT have the following general layout:

12 3 7 8 9

ß

à

4

5

6

1

Menu

2

Start

3

Display of the current navigation level

OPERATION 8

8026183 / 2021-04-29 | SICK

Subject to change without notice

13

4

Device information

5

Page navigation

6

Notifications

7

Update page

8

Restore factory settings

9

Activate/Deactivate Edit mode

ß

Parameterization page, with sub-pages if applicable

à

Operating mode

Table 2: Function

Menu Click this button to show/hide the “Page selection” menu to make

it easier to navigate on smaller screens. The button is highlighted

in light blue when the device tree is hidden.

Start Click the Start button at any time to return to the “STATUS” device

page.

Device information The product name, the application-specific name, the firmware

version, and the serial number are displayed in this area at the top

left.

Page navigation Clicking on the individual levels displays different parameterization

pages.

Notifications Notifications for the SLT are displayed at the bottom of the screen.

They are provided for informational purposes when exchanging

parameterizations or when errors occur. Each notification can be

acknowledged by clicking on the entry.

Update page After clicking on this button, the page contents are updated.

Restore factory settings When you click on this button, all settings of the SLT are reset to

their factory values.

Edit Click the Edit button to change the settings on the current parame‐

terization page. When the Edit button is pressed, it is highlighted in

light blue. Configurable pages are displayed in gray until Edit mode

is activated.

Operating mode With the SLT, there is only the RUN operating mode. No password

is provided for this operating mode. With other SICK products,

there are other operating modes that require entry of a password.

8.2.1.2.1 STATUS page

The “STATUS” page is the start page for the SLT. On this page, you can set the process

data that is cyclically transmitted to the SLT. The process data available for writing

differs depending on the operating mode set.

8 OPERATION

14

8026183 / 2021-04-29 | SICK

Subject to change without notice

NOTICE

For writing process data on the status side, at least SOPAS ET version V2021.2 is

required. Alternatively, an IO-Link master can be used to write the process data.

The following process data can be set:

•

Signal lamp mode

The configured LED groups as well as the SLB buzzer can be switched on and off

via the switches.

•

Filling level mode

Here the text field can be used to specify the filling level value in 0-100% format,

which is transmitted cyclically to the SLT as process data. The SLB buzzer can also

be turned on and off with a switch here.

•

Animation mode

In this mode, the animation can be switched on and off. The animation can also

be reset and its speed can be adjusted. The SLB buzzer can also be turned on and

off with a switch here.

8.2.1.2.2 Configuration page

The Configuration page is divided into four tabs:

•

General

•

Color

•

Buzzer

•

Alarm

General tab

In the GENERAL tab, the SLT can be completely shut off. In addition, the brightness of

the lamp can be adjusted. The slider can be used to set values between 0 and 100%

in 10% increments. The Find me function can also be activated here. If this function is

activated, the IO-LINK LED in the lower part of the SLT starts flashing with a frequency

of 1 Hz (clock/pause 50%) until the button is clicked again. This function can be used

to identify devices that have already been mounted.

Color tab

The appearance of the lamp can be configured in the COLOR tab. The operating modes

described in chapter 3.4 are available. Configuration is done by selecting the different

options such as color, light pattern and frequency from the CONFIGURATION OF COLOR

OPERATION 8

8026183 / 2021-04-29 | SICK

Subject to change without notice

15

area on the left. After the desired option has been activated by clicking on it, it can be

transferred to the SLT in the preview in the center area of the page by clicking again

in the desired segment. Operating mode-specific functions are available for selection in

the area on the right. In the center part of the tab, the corresponding configurations are

displayed as previews. The colors and icons signal how each segment is configured.

Figure 1: Color tab

Table 3: Functions of the COLOR tab

Operating mode selection Selection of operating mode:

- Signal lamp mode

- Filling level mode

- Animation mode

Color palette A color palette with 21 different colors is available.

In Signal lamp mode, 7 colors are available in the preselection.

Another color can be added by clicking the button with the plus

sign. By clicking on the desired color, it can be transferred to the

layout at the corresponding position.

Light pattern Four different light patterns are available: Continuous light, flash‐

ing, strobe, pulsating. The illuminated images can be activated by

clicking on them. You can see this with the blue coloring of the

selected button.

The selected light pattern is transferred by clicking on the individ‐

ual segment in the layout.

Frequency The frequency of the flashing, strobing or pulsating light patterns

can also be set.

The following frequencies are available:

- Slow (0.5 Hz)

- Medium (1.5 Hz)

- Fast (2.0 Hz)

The activated frequency is marked in blue.

Switch-on behavior of LEDs This selection is available in Filling level and Animation mode.

A selection is made to determine whether the LEDs turn on from

the bottom end of the SLT upwards (bottom up) or from the top

end downwards (top down).

Segment representation This selection is available in Filling level and Animation mode.

It is defined whether the LEDs should change color or light pattern

as soon as the LED segment above them begins to glow. There are

three options here:

- The previously activated segments retain their light animation.

8 OPERATION

16

8026183 / 2021-04-29 | SICK

Subject to change without notice

- The segments that are already illuminated stop their light pattern

animation as soon as a new segment is added, but remain acti‐

vated. Only the uppermost segment shows an animation.

- All segments show the light pattern of the uppermost segment

Layout The layout shows a preview of the configuration of the SLT. The

colors and icons symbolize how the lamp will look later.

Group separation This function is only available in Signal lamp mode.

Activating the function turns off one LED segment between the

groups. This allows for better visual separation of the individual

groups.

Transfer values This selection is only available in Signal lamp mode.

After changing the size of the individual groups in Signal lamp

mode, this configuration must be transferred to the SLT by clicking

the “Transfer values” button.

Reset This selection is available in Signal lamp and Filling level mode.

Clicking on the RESET button resets the number of LED segments

in Signal lamp mode to the presetting. The limit values are reset in

Filling level mode.

Delete values This function is only available in Signal lamp mode.

By deleting the values, the number of LEDs in the changeable

groups is set to 0 and group 1 is then automatically set to 20.

Configuration of limit val‐

ues

In Filling level mode, a value between 0 and 100% can be set for

each LED segment. It is important to note that the value in each

LED segment may not be higher than the value in the segment

above it.

Animation repetition This selection can be used to set the repetition pattern of the

animation. The Loop (always building up from bottom to top) and

Bounce (first building up from bottom to top, then going down

from top to bottom) properties are available.

Buzzer tab

The SLB alarm unit can be configured in the BUZZER tab. In addition to the volume,

various sound effects can also be set. The following sound effects are available:

Sound effect Description Frequency

1 Off Off

2 Continuous tone Continuous tone 3,378 Hz

3 Beeping Fast, periodic tone 3,378 Hz

4 Whistling Fast, high/low tone 2,016 Hz &

3,012 Hz

5 Sweep Sweeping tone 1,000 Hz &

4,032 Hz

6 Beeping, slowly Slow, periodic tone 3,378 Hz

7 Beeping, with pause Fast, periodic tone with pause

1)

3,378 Hz

8 Whistling, with pause Fast, high/low tone with pause

1)

2,016 Hz &

3,012 Hz

9 Sweep, with pause Sweeping tone with pause

1)

1,000 Hz &

4,032 Hz

1)

Pause: 500 ms on / 500 ms off

OPERATION 8

8026183 / 2021-04-29 | SICK

Subject to change without notice

17

Alarm tab

Three user-defined light patterns (profile 1 to 3) can be configured in the ALARM tab. For

this purpose, an individual color sample can be created after selecting one of the three

profiles. The selection of patterns is done as with the regular color selection in the Color

tab. These three profiles can be selected for display on the STATUS page in all three

operating modes:

•

Diagnostics page

The current status of the SLT can be checked on the Diagnostics page. If the

device reports an error, it will be displayed here. The sending of IO-Link events can

also be deactivated here.

•

Identification page

The device identification details are displayed on the Identification page. An appli‐

cation-specific name and a device function name can be specified here.

•

Settings page

The language of the user interface can be selected on the SETTINGS page.

8.2.1.2.3 Diagnostics page

The current status of the SLT can be checked on the Diagnostics page. If the device

reports an error, it will be displayed here. The sending of IO-Link events can also be

deactivated here.

8.2.1.2.4 Identification page

The device identification details are displayed on the Identification page. An applica‐

tion-specific name and a device function name can be specified here.

8.2.1.2.5 Settings page

The language of the user interface can be selected on the Settings page.

The following settings are possible:

•

Language: English/Englisch, German/Deutsch

Use the INFORMATION button to get more detailed information about the version of the

interface software.

8.2.1.3 Configuration via IO-Link master based on the IODD

Instead of the SiLink2 IO-Link master, other IO-Link masters can also be used to

configure the SLT. For example, the SIG200 IO-Link master (available at www.sick.com)

enables the use of a graphical user interface generated from the IODD (IO-Link device

description file) of the SLT. No SDD is necessary here, because the configuration is

done directly via the parameters described in the IODD. For more information on the

procedure, please refer to the SIG200 User Manual, which can also be downloaded at

www.sick.com.

8.2.1.4 Configuration via direct access to service and process data

The third option for configuring the SLT is to directly access the service and process

data via an IO-Link master or a PLC with a connected IO-Link master terminal without

using a graphical user interface. When using this type of configuration/control, informa‐

tion about the process data structure for control and service data (ISDUs) is required for

configuration.

NOTE

Detailed information can be found in the IO-Link description (8026795) and / or the

IODD description.

8 OPERATION

18

8026183 / 2021-04-29 | SICK

Subject to change without notice

9 Troubleshooting

The Troubleshooting table indicates which measures are to be taken if the device stops

working.

Table 4: Troubleshooting

LED indicator/fault pattern Cause Measures

Off No voltage or voltage below

the limit values

Check the power supply,

check all electrical connec‐

tions (cables and plug connec‐

tions)

Voltage interruptions Ensure there is a stable power

supply without interruptions

Device is defective If the voltage supply is OK,

replace the device

10 Disassembly and disposal

The device must be disposed of in line with applicable country-specific regulations.

When disposing of them, you should try to recycle them (especially the precious met‐

als).

NOTE

Disposal of batteries, electrical and electronic devices

•

In accordance with international regulations, batteries, rechargeable batteries and

electrical and electronic devices must not be disposed of with household waste.

•

The owner is required by law to dispose of these devices at the appropriate public

collection points at the end of their service life.

•

WEEE: This symbol on the product, its packaging or in the document

indicates that a product is subject to the specified regulations.

11 Maintenance

SICK devices are maintenance-free.

We do, however, recommend that the following activities are undertaken regularly:

•

Clean the device

•

Check the fittings and plug connectors

Use a soft cloth moistened with water to clean the device.

Do not use thinners, gasoline or oil.

In case of failure or damage of the SLT caused by aggressive media, no claims for

defects can be asserted.

No modifications may be made to devices.

Subject to change without notice. Specified product properties and technical data are

not written guarantees.

TROUBLESHOOTING 9

8026183 / 2021-04-29 | SICK

Subject to change without notice

19

12 Technical data

12.1 Technical specifications

Smart Light Tower

SLT060-0B010J700

Smart Light Buzzer

SLB060-0B010K700

Part number 6075938 6076072

Supply voltage U

B

DC 18 V ... 30 V -

Current consumption Max. 300 mA

1)

-

Connection M12, 5-pin, A-coded Proprietary connection

Mounting direction Upright Upright

Number of LED segments 20 -

Volume - Typ. 88 dB (at 1 m dis‐

tance)

Frequency - 1,000 - 4,032 Hz

Ambient temperature, operation -25 °C … +50 °C -20 °C … +50 °C

Ambient temperature, storage -30 ℃ … +60 ℃ -20 °C … +50 °C

Ambient humidity ≤ 90% (non-condens‐

ing)

≤ 90% (non-condens‐

ing)

IO-Link 1.1 -

Enclosure rating IP65 IP65 (in mounted state)

Protection class III III

Dimensions 281 x Ø 60 mm 53.5 x Ø 60 mm

Weight 0.54 kg 0.06 kg

Housing material Polycarbonate (PC) Polycarbonate (PC)

1)

Including accessories for beeper SLB060-0B010K700

12.2 Dimensional drawings

1

4

5

6

7

2

3

8

9

ß

à

Ø 60

(2.36)

Ø 52

(2.03)

281 (11.06)

201.5 (7.93)

25

(0.98)

53.5

(2.11)

1

Cover

2

Main body

12 TECHNICAL DATA

20

8026183 / 2021-04-29 | SICK

Subject to change without notice

Страница загружается...

SICK SLT Smart Light Tower Инструкция по эксплуатации

Похожие модели бренда

Модели других брендов