Yamaha V1 Инструкция по применению

EN

OWNER’S MANUAL

Version 1.2

Getting Started

DME Designer Owner’s Manual

2

Getting Started with DME Designer

Thank you for purchasing the DME64N/24N.

Your DME64N/24N mixing engine, together the DME Designer software, lets you build a custom audio

system installation that can support an incredible variety of conditions. You can build an entire system

from input to output with the DME Designer software, then send the data from that system to the

DME64N/24N, which becomes an independent processor.

An amazing variety of applications are possible, including audio installations, sub-mixing, speaker

system control, matrix/routing, and multi-effect processing.

In this manual the abbreviation “DME” refers to the DME64N/24N.

SPECIAL NOTICES

• The software and this Owner’s Manual are the exclusive copyrights of Yamaha Corporation.

• Use of the software and this manual is governed by the license agreement which the purchaser fully

agrees to upon breaking the seal of the software packaging. (Please read carefully the Software

Licensing Agreement at the end of “DME Designer Installation Guide” before installing the

application.)

• Copying of the software or reproduction of this manual in whole or in part by any means is expressly

forbidden without the written consent of the manufacturer.

•Yamaha makes no representations or warranties with regard to the use of the software and

documentation and cannot be held responsible for the results of the use of this manual and the

software.

• This disc is a CD-ROM. Do not attempt to play the disc on an audio CD player. Doing so may result

in irreparable damage to your audio CD player.

• The company names and product names in this Owner’s Manual are the trademarks or registered

trademarks of their respective companies.

• The screen displays as illustrated in this Owner’s Manual are for instructional purposes, and may

appear somewhat different from the screens which appear on your computer.

• Future upgrades of application and system software and any changes in speciﬁcations and

functions will be announced separately.

• Windows

®

is the registered trademark of Microsoft

®

Corporation.

NOTE

Here the abbreviation “DME” does not include the “DME32.”

NOTE

This manual is based on the English version of the software. Illustrations, command names, window names, and similar

information are from that version. Some items may differ from what you see on the computer screen, depending on which

operating system you are using.

Getting Started

DME Designer Owner’s Manual

3

About DME Designer

DME Designer is software that provides an integrated environment where you can build and control

systems that use DME.

Audio systems with DME are built on the computer screen in block diagram format using the DME

Designer software. Information about the inputs/outputs along with the arrangement of components

and their connections is called the “conﬁguration.”

The software sends DME settings, along with conﬁguration and parameter data, to the DME unit

through a USB or Ethernet connection. Once the data is transferred, the DME unit can be

disconnected from the computer and used as an independent processor. The DME can also be kept

connected to the computer and controlled in realtime from DME Designer software.

If multiple DME units are connected to the computer, you can use the DME Designer software to build

a conﬁguration that includes those multiple units.

For a DME overview and glossary, see the “DME64N/24N Owner’s Manual.”

Systems built with DME Designer can have multiple zones within an area and multiple conﬁgurations

and scenes within a zone. However, only one area, zone, or conﬁguration can be made active and

edited at a time. When active these are called the “Current Zone,” “Current Scene,” and “Current

Conﬁguration.”

■ One DME unit/Zone

Area This means the entire site, and is therefore the uppermost level for a system built using

DME Designer. At least one zone must be located within the area.

Zone Speciﬁes a space that has individual sound effects within the area, and creates DME

connection conditions. You can create and switch between multiple conﬁgurations.

Conﬁguration Information related to the layout and connection of components in a zone.

Scene Information related to conﬁguration assigned to a zone and the settings of the

components included in the conﬁguration.

Component An object that is arranged within the Conﬁguration window.

No.

001

002

003

004

005

006

....

Confuguration

Output Processor for Dome

...

Scene Name

All On

Opening

Band Set 1

Band Set 2

Band Set 3

...

Preset

All On

BGM & MC

Band 1

Band 2

Band 3

Microphone

Mixer

External Head Amp

etc...

Power Amp

Processor

etc...

Input

External Device (MIDI, GPI, DAW, AMX/Crestron)

Audio signal

Notes

Zone

Output

Control signal

Data explanation

Setting preset data

LCD Display

Dome Low

Dome Mid

Dome Hi

....

Assigned Parameter

Crossover: Output Low: Level

Crossover: Output Mid: Level

Crossover: Output Hight: Level

(No Assign)

User Defined Button Scene Manager

Specifies the parameter to be changed.

Specifies the configuration

and preset data combination.

Configuration

Output Processor for Dome

Local parameter link settings

External device settings

MY8-AE

(Input)

MY8-AE

(Output)

Cross-

Over

EQ

Delay EQ Dyn

Delay

All On Component value

BGM & MC

Band 1

Band 2

Band 3

Preset data for output processor

Set the value

Getting Started

DME Designer Owner’s Manual

4

■ Two DME units/Zone

When one DME unit doesn’t provide sufﬁcient processing power, up to 16 DME units can be used

DME#2

Configuration

Output Processor

for Hall

Local parameter link settings

External device settings

All On

BGM & MC

Band

Zone

LCD Display

Dome Low

Dome Mid

Dome Hi

Hall Low

Hall Mid

Hall Hi

....

Assigned Parameter

#1: Crossover: Output Low: Level

#1: Crossover: Output Mid: Level

#1

:

Crossover

:

Output Hight

:

Level

#2: Crossover: Output Low: Level

#2: Crossover: Output Mid: Level

#2

:

Crossover

:

Output Hight

:

Level

No.

001

002

003

004

005

006

....

Configuration

Output Processor for Dome

...

Scene Name

All On

Opening

Band Set 1

Band Set 2

Band Set 3

...

Preset

All On

BGM & MC

Band 1

Band 2

Band 3

Configuration

Output Processor for Hall

...

Preset

All On

BGM & MC

Band

User Defined Button

Scene Manager

DME#1

Configuration

Output Processor

for Dome

Local parameter link settings

External device settings

All On

BGM & MC

Band 1

Band 2

Band 3

Preset data Preset data

External Device (MIDI, GPI, DAW, AMX/Crestron)

Microphone

Mixer

External Head Amp

etc...

Power Amp

Processor

etc...

Input Output

DME#1

DME#2

For DME#2

For DME#1

Specifies the parameter to be linked between DME units.

Grobal Parameter Link

For DME#1 For DME#2

Audio signal

Notes

Control signal

Data explanation

Setting preset data

Selects the parameter to be

edited from two DME units.

Specifies the configuration and preset

data combination in each DME

Getting Started

DME Designer Owner’s Manual

5

System Requirement

Common data for DME units in the same zone

Scene Manager A “scene” is information that is used to change the audio processing content.

A combination of a conﬁguration and preset data is speciﬁed for each scene.

A Scene Manager is function used to memorize and manage scenes. Up to 999

scenes can be memorized, and each scene is managed by number.

MIDI Program Change

settings

This setting is necessary to switch scenes using MIDI messages.

User Deﬁned Button setting This information is necessary to control component parameters from the unit’s

panel. Up to 24 parameters can be memorized.

Global parameter link settings This information is necessary to allow operation of similar parameters to be

linked between multiple DME units.

Separate data for individual DME units

Conﬁguration This information deﬁnes the conﬁguration of audio processing, audio input/

output, and external device components and the connections between

components required to achieve the desired audio processing.

Local parameter link

settings

This information is necessary to allow linked operation between similar

parameters within a single DME unit.

External device settings This information is necessary to allow control of component parameters from

external devices.

Independent settings are required for each external device.

The following external devices can be used:

• MIDI controller( MIDI Control Change, Paramter Change)

• GPI controller

• DAW controller

• AMX, Crestron, and similar remote controllers.

Preset data These are the parameter values for the components included in a conﬁguration.

Audio processing details can be changed by changing the preset data.

The following component types include preset data:

• GEQ, Matrix Mixer, and other audio processing components.

• Internal AD/DA (DME24N), Cascade (DME64N), and MY Card I/O

components.

• External device components for external head amps (AD8HR, AD824).

Operating System Windows

®

XP Professional/XP Home Edition/2000 Professional

CPU 1 GHz or better Intel

®

Pentium

®

/Celeron

®

family processor

Memory At least 256 MB

Hard Disk Capacity At least 300 MB

Display 1,280 x 1,024 pixels or better/High Color 16 bit or better

Other Mouse, CD-ROM drive, 100Base-TX/10Base-T Ethernet or USB connection

environment.

Getting Started

DME Designer Owner’s Manual

6

Main Changes from V1.0 to V1.1

■ Main Panel Window

• Instead of the former Parameter Link function, there are now two functions: a Global Link function

that links parameters within all DMEs in a zone and a Local Link function that links parameters

within a single DME unit. (→ page 73)

• The Synchronization function can now not only send data from DME Designer to the DME unit,

but can also synchronize by reading data from the DME unit. (→ page 75)

• Scene Increment/Decrement and Time Adjustment can now be assigned in the GPI input

function. (→ page 80)

• DME unit events can now be recorded by the Event Logger function and displayed in the Event

Logger window. (→ page 111)

• The time for executing an event can now be set by using the Event Scheduler function.

(→ page 116)

• Parameters in the current conﬁguration can now be listed on the display and printed out by using

the Parameter List function. (→ page 124)

• The Wav File Manager can manage Wave ﬁles played by the Wav File Player. (→ page 128)

• Settings can be made by the DAW Control function that are used for controlling DMEs from a

DAW controller. (→ page 132)

• DME unit data can now be saved as a backup ﬁle by using the Backup function. (→ page 135)

■ Designer Window

• The port name display can now be switched between long name display and short name display.

(→ page 148)

• DME64N cascade connections can now be set. (→ page 165)

• Priority items can now be set when compiling conﬁgurations by using the [Compile Priority]

function in the “Preferences” dialog box. (→ page 209)

• Delay time can now be displayed for each component by using the Show Signal Delay function.

(→ page 246)

• Monitoring points can now be edited by using the “Monitoring Point List” dialog box. (

→

page 247

)

• The status of connections in a conﬁguration can now be analyzed in advance by using the

Analyze function, without connecting the DME unit. (→ page 249)

•You can now set the action that occurs when you double-click a user module object. You can also

turn user module security ON or OFF, and set a password. (→ page 254)

• Libraries with component parameters saved in them can now be recalled from the context menu

for a component object. (→ page 277)

•A new rule for wiring prohibits connections to terminals that would short the terminator.

■ Component Editor/Component

•A status bar has been added to the component editor. It displays the component name,

component ID, and parameter IDs for parameters that are being edited. (→ page 265)

•A Snap function has been added that records parameters in the editor temporarily. Parameter

sets can then be switched by using the Snap buttons. (→ page 273)

• The meter's peak hold function can now be turned ON or OFF. (→ page 291)

•A Wav File Player component has been added for playing Wave ﬁles. (→ page 359)

• An effect component called SPX has been added that supports many different effect

applications, such as reverb, delay, and modulation effects, along with complex combinations of

multiple effects. (→ page 397)

•A Slot Out component editor has been added. (→ page 409)

• An Undo/Redo function is now available when using the design mode. It can undo the most

recent operation (control movement/resize/deletion).

Getting Started

DME Designer Owner’s Manual

7

Changes from V1.1 to V1.2

■ Main Panel Window

• The synchronization algorithm has been reﬁned for faster synchronization.

• Synchronization now can be executed from DME to DME Designer without any break in the

sound.

• In the following cases, synchronization can be executed from DME Designer to DME without any

break in the sound:

The second or later synchronization after starting DME Designer* and when differences in data

between the DME and DME Designer are limited to parameters within components, AD824/

AD8HR/DME24N AD/DA setting data, or MY card setting parameters.

* If the ﬁle was saved when DME Designer was closed, there will be no break in sound even in the ﬁrst

synchronization after saving.

• Compile speed has been increased.

Up to three times faster when AutoDelayCompensation is turned On.

Up to two times faster when AutoDelayCompensation is turned Off.

• Synchronization is possible when no MY card or a different MY card is installed in the DME unit

(a conﬁrmation dialog will appear).

• An option to automatically close the dialog after synchronization has been added. (→ page 37)

•A progress bar has been added to the Synchronization dialog. (→ page 36)

•A message appears to warn when synchronization will cause muting.

• The following operations can be performed while on line:

- Scene storage.

- Scene name changes.

- Fade ON/OFF and Fade Mode changes.

- Fade time changes.

- Parameter link setting changes.

• When a scene store is executed, that scene becomes the current scene.

•Wave ﬁles can be saved as DME data ﬁles, and are included in import/export operations.

(→ page 32)

•Wave ﬁles can be saved in the Wav ﬁle library.

• Event Log events can be output via GPI. (→ page 115)

• The on-line indicator appears as a button which can be used to switch between on-line and

off-line. (→ page 43)

• Scene edits cause the EDIT indicator to appear. (→ page 42)

• An auto ﬁle save function (Auto Save, post synchronization) has been added. (→ page 53)

• Different zones can be speciﬁed for use by different users. (→ page 56)

• Scene parameters related to User Deﬁned Button, Program Change, GPI In and GPI Out can be

set via the Scene Manager. (→ page 63)

• [Select All] and [Clear All] buttons have been added to the Scene Manager Recall Safe dialog.

(→ page 67)

• User Control can be created for individual users as well as security levels. (→ page 70)

•A Remote Control Setup List has been added. (→ page 123)

This list can be used to make detailed settings for a new software protocol that allow the DME to

be controlled from AMX, Crestron, and similar devices.

Refer to the “DME-N Remote Control Protocol Speciﬁcations” document for details about the

communication protocol. Information about the “DME-N Remote Control Protocol Speciﬁcations”

document can be found at the Yamaha pro Audio website (URL below).

http://www.yamahaproaudio.com/

• It is possible to specify whether listed events will be executed by the Event Scheduler.

(→ page 116)

Getting Started

DME Designer Owner’s Manual

8

• The order of same-time events can be changed in the Event Scheduler. (→ page 116)

• Exceptions can be speciﬁed for Event Scheduler execution day/time. (→ page 122)

• Event Scheduler execution times can be speciﬁed in 1-second increments. (→ page 121)

• Head amp gain and MY-Card can be set via GPI, MIDI, User deﬁned Button, DAW Control.

• Parameter values, scene recall, GPI output, Wave ﬁle playback, and head amp gain can be set

via the User Deﬁned Buttons. (→ page 98)

• The Component Lock function dialog is separate from the Parameter List dialog. (→ page 127)

• Shortcuts can be freely set as required. (→ page 134)

• Files can be saved in the DME unit. (→ page 52)

•A [Close All Editor Windows] button has been added to the Window menu. (→ page 51)

• External head amp parameters will be recognized by the DME unit when either the DME or the

external head amp (AD824, AD8HR) are turned on. Execute a scene recall to send DME settings

an external head amp.

• This manual is now separate from the DME Designer installer, and can not be accessed from the

DME Designer menus.

■ Designer Window

• The following operations can be carried out via the shortcut keys.

- Navigator

- Activate Navigator

- Activate Toolkit

- Activate Design Window

- Select Left Port and Start Wiring

- Select Right Port and Start Wiring

- Wire Auto Single to Right

- Wire Auto Multi to Right

- Wire Auto Single to Left

- Wire Auto Multi to Left

- Delete Wire

• It is now possible to simultaneously edit multiple objects of the same type.

Example: Change the thickness or color of multiple wires at once.

• Files related to user modules (user module ﬁles, library ﬁles, user module editor ﬁles) can be

combined and exported/imported as a single ﬁle.

• Port colors can be independently speciﬁed for each port type. (→ page 156)

• Default wire thicknesses and types can be independently speciﬁed for each port type.

• An automatic hot-spot connection function has been added. (→ page 225)

• Port display has been added to External Device, Picture, DME, and ICP1 objects.

• When drawing wires the keyboard cursor keys can be used to move the mouse cursor, and the

<Enter> key can be used to create nodes.

• When drawing wires <Shift> key plus <→> key and <Shift> key plus <←> key combinations can

be used to automatically connect horizontally-aligned hot spots.

• DME object ports can be freely speciﬁed.

• Compilation of conﬁgurations with loop connections is possible when Auto Delay Compensation

is On.

• The name has been changed from “Foot Monitor” external device to “Floor Monitor.”

• Addition External Device types have been provided.

• External Devices can be double-clicked to open a ﬁle saved by other applications. (

→

page 172

)

• Picture objects can be double-clicked to open a speciﬁed editor. (→ page 187)

•Text objects can be double-clicked to open a speciﬁed editor. (→ page 190)

Getting Started

DME Designer Owner’s Manual

9

• User module port labels can be edited. (→ page 183)

• Graphics can be placed to represent user modules. (→ page 183)

• The Legend ﬁeld automatically resizes to accommodate project names and titles of different

lengths.

•A Generic “MY-Others” setting has been provided to accommodate third-party MY cards.

■ Component Editor Window

• Undo and Redo are now shortcut compatible.

•A scroll bar appears when the size of the component editor window is reduced.

• The size and position of the component editor window are memorized.

• An option to allow mouse-over zooming of the edit box has been added. (→ page 266)

•A [Back] button that allows switching between related parent and child windows has been

added. (→ page 265)

•A [Close All Editor Windows] button has been added to the contextual menu.

• Source Selector, Speaker Processor, Limiter, Slot In, Cascade In, and Cascade Out components

have been added.

• The Delay algorithm has been revised. (→ page 332)

- LEVEL and MUTE are effective when Delay is Off for each channel.

- The name of the overall Delay [On] parameter has been changed to [All Bypass].

• The bus send level range for Delay, Matrix, and Matrix Mixer components has been changed to

-∞ through 0.0 dB.

• Snap copy is possible. (→ page 274)

• Snap can be retained until the application is quit or another ﬁle is opened.

• Security status is displayed in the user module editor status bar.

• Multiple controllers can be selected by clicking while holding the <Ctrl> key when the editor is in

the design mode. (→ page 286)

• [Picture], [Text], [Box], [Ellipse], and [Frame] have been added to the tool palette of the user

module editor and user control editor design mode. (→ page 279)

• Controller properties can be accessed by double-clicking controllers in the user module editor or

user control editor design mode. (→ page 303)

• Picture and Text objects can be clicked to open a speciﬁed editor in the user module editor or

user control editor.

• The User Module Editor and User Control Editor offer a greater range of customization options for

color, size. etc., of the placed controls.

■ MIDI Setup

•A MIDI Setup minimize function has been added.

■ V1.2 Precautions

• When using project ﬁles (*.daf) created by version 1.1.5 or earlier, synchronize from the DME

Designer to the DME unit for the ﬁrst synchronization.

•Project ﬁles (*.daf) created using version 1.2 will not open properly on version 1.1.

IN

Input

Mute

Input

Level

Input

Mute

Input

Level

On

Delay On

Delay All Bypass

OUT

Mute Level

On Mute Level

IN

Delay

DME Designer Owner’s Manual

10

Contents

Chapter 1 Before Using 11

Installing DME Designer.....................................................11

Starting DME Designer.......................................................11

Closing DME Designer.......................................................13

Chapter 2 DME Designer Overview 14

Names and Functions of the Windows...............................14

Users and Security.............................................................19

Project Files........................................................................22

DME Data File....................................................................30

Configuration Creation Procedure......................................34

Online.................................................................................35

Chapter 3 Main Panel Window 39

Main Panel Window............................................................39

Main Panel Window Menu..................................................44

DME File Storage...............................................................52

Preferences........................................................................53

Security (Creating Users and Making User Settings).........55

Scene Manager..................................................................63

User Control .......................................................................70

Parameter Link...................................................................73

Synchronization

(DME Designer and DME Unit Synchronization)................75

GPI .....................................................................................79

MIDI....................................................................................90

User Defined Button (User Defined Parameters)...............98

Word Clock.......................................................................102

Monitor .............................................................................104

Clock ................................................................................105

Language Settings ...........................................................106

DME Firmware Update.....................................................107

Event Logger....................................................................111

Event Scheduler...............................................................116

Remote Control Setup List ...............................................123

Parameter List..................................................................124

Component Lock ..............................................................127

Wav File Manager ............................................................128

DAW Control.....................................................................132

Shortcut Keys...................................................................134

Backup .............................................................................135

Chapter 4 Designer 136

Editing Configurations ......................................................136

Designer Window .............................................................137

Designer Window Menu ...................................................144

Toolkit Window.................................................................152

Objects .............................................................................156

Design Window Shared Settings and Operations ............207

Drawing and Editing Wires ...............................................219

Adding, Deleting, and Renaming a Zone..........................231

Adding, Deleting, and Renaming a Configuration.............233

Area Window ....................................................................235

Zone Window....................................................................237

Configuration Window.......................................................242

User Module .....................................................................250

Chapter 5 Components 259

Types of Components.......................................................259

Component Editor Window...............................................264

Snap .................................................................................273

Library...............................................................................275

User Control/User Module Editor......................................279

Creating Parameter Links.................................................314

Chapter 6 Component Guide 316

Crossover .........................................................................316

Crossover Processor........................................................320

Delay.................................................................................332

Dynamics..........................................................................334

Equalizer (EQ)..................................................................344

Fader ................................................................................348

Filters................................................................................349

Meter.................................................................................357

Miscellaneous...................................................................358

Mixer.................................................................................360

Pan ...................................................................................378

Router...............................................................................386

Source Selector................................................................388

Speaker Processor...........................................................390

SPX...................................................................................397

Slot....................................................................................408

Cascade............................................................................410

Internal Head Amp............................................................412

MY-Card ...........................................................................413

Remote Controlled Head Amp..........................................417

Component Glossary........................................................419

Troubleshooting 423

Index 424

DME Designer Owner’s Manual

11

Chapter 1 Before Using

Installing DME Designer

To use DME Designer, you must ﬁrst install the software on the computer. Before you can connect the

DME Designer software to the DME unit, send and receive conﬁgurations, or perform control, you must

ﬁrst install the USB MIDI Driver or the DME-N Network Driver, according to how you will be connecting,

and then make the appropriate settings.

For instructions about how to install DME Designer and about the installation and setup method for the

MIDI driver and DME-N Network Driver, see the “DME Designer Installation Guide.”

Starting DME Designer

The DME Designer software is started from the [Start] menu. DME Designer is used with one user

logged on. The user logs on when the software is started.

■ DME Designer Start Up and Logon (When Auto-Logon Is Not Set)

1 Click [Start] ➞ [All Programs] ➞ [YAMAHA OPT Tools] ➞ [DME Designer] ➞ [DME

Designer].

The “Log On” dialog box will be displayed.

2 Click the [▼] at the right of the [User] box, and select the user.

If no user has been created, only [Administrator] will appear in the list. When starting DME

Designer for the ﬁrst time after installing, select [Administrator].

NOTE

In Windows2000, click [Start] → [Programs] → [YAMAHA OPT Tools] → [DME Designer] → [DME Designer].

NOTE

Automatic log-on is the default setting. If the automatic logon feature is enabled, the “Log On” dialog box will not be

displayed when the application is started. Instead, the auto-logon user will be logged on automatically. See page 21

for information about auto-logon.

Chapter 1 Before Using

DME Designer Owner’s Manual

12

3 Enter the password into the [Password] box.

Enter the password set for the user.

If no password has been set, leave the password box blank when you log on.

4 Click the [OK] button.

DME Designer starts up.

■ When Automatic Logon Has Been Set (page 21)

If automatic logon has been set, the “Log On” dialog box will not be displayed. The user set for

automatic logon will be logged on.

With automatic log on, even if a password is set for a user, it will not be requested during log on.

This is useful when logging on a speciﬁc user.

■ Starting by Opening a Project File

DME Designer starts when a project ﬁle with a saved conﬁguration is opened. When the project ﬁle

is opened, DME Designer is started with the window conﬁguration that was in place when the ﬁle

was last saved.

Chapter 1 Before Using

DME Designer Owner’s Manual

13

Closing DME Designer

To close DME Designer, click [Exit] on the [File] menu of the Main Panel window. It can also be closed

by clicking the [Close] button on the Main Panel window.

1 Click [Exit] on the Main Panel window [File] menu.

When you try to close DME Designer, “Project File has been modiﬁed. Save?” will be displayed in a

dialog box.

2 To save the ﬁle, click [Yes]. To close without saving, click [No].

If you click [Yes], the ﬁle currently saved with the same name will be overwritten. If the ﬁle has not

been saved, the File Save dialog box will always be displayed.

NOTE

Sometimes the “Project File has been modiﬁed. Save?” dialog box will not be displayed.

DME Designer Owner’s Manual

14

Chapter 2 DME Designer Overview

Names and Functions of the Windows

The DME Designer software has several windows, including the Main Panel window, Designer window,

Component Editor window, Resource Meter window, and others.

Main Panel Window

Menus and buttons are available in the Main Panel window. The current DME Designer environment,

including the active scene and zone, the currently logged on user name, and the connection status to

the DME unit are displayed on the right side of the Main Panel window.

Main Panel Window

Designer Window

Component Editor Window

Resource Meter Window

Chapter 2 DME Designer Overview

DME Designer Owner’s Manual

15

Designer Window

The Designer window displays several different windows. First among them is the Area window, where

you can manage the entire system. The Area window includes one or more Zone windows, which in

turn include one or more DME units that are used to build a zones within the area. Next is the

Conﬁguration window, where you create the internal conﬁguration of each DME unit. Within the

Conﬁguration window are the User Module windows, where you can assemble often-used

components into presets; the Toolkit window, which displays objects used in the other windows as the

basic building blocks for sound designs; and the Navigator window, which lets you grasp the overall

status of the system at a glance.

■ Area Window

The Area window is used for designing areas, which manage the entire system. While at least one

zone is included within an area, multiple zones can be arranged there.

Toolkit Window

Conﬁguration Window

User Module Window

Navigator Window

Zone Window

Zones

Chapter 2 DME Designer Overview

DME Designer Owner’s Manual

16

■ Zone Window

The Zone window is used to design zones within the area. A zone is a more concrete blueprint that

includes at least one DME. It shows the DME’s connections with other devices and the wiring

between them. You can create multiple zones.

The DME units and connected devices are arranged in each Zone window, creating conﬁgurations.

■ Conﬁguration Window

The Conﬁguration window is used to design the internal conﬁguration of each DME unit contained

in the Zone window. By arranging and connecting components (audio processors like mixers,

compressors, effects, and crossovers, along with parts like faders and meters) in the Conﬁguration

window, you can create things like complex processors or matrix mixers, that determine the actual

internal structure that operates each DME unit.

■ User Module Window

The User Module window is used for designing user modules that can be arranged in the

Conﬁguration window. You can create original modules by combining multiple examples of often-

used components. When you save these modules as presets, you can recall them easily whenever

you want.

Conﬁgurations

Components

Chapter 2 DME Designer Overview

DME Designer Owner’s Manual

17

■ Toolkit Window

The Toolkit window displays the objects that you can use in each window that can be displayed in

the Designer window. Those windows are the Area, Zone, Conﬁguration, and User Module

windows. The Toolkit displays different objects, according to the currently active window. To place

an object in a window, double-click it in the Toolkit window where it is displayed or drag it to the

currently active window.

■ Navigator Window

The Navigator window displays the area, zones, conﬁgurations, and components in a hierarchal

fashion that lets you check their status as a whole. When editing ofﬂine, you can click an area

name, zone name, or conﬁguration name to make that window active. Clicking a component name

will open the component editor window for that component.

■ Objects and Components

“Object” is the name for the parts that are arranged in the various design windows, such as the

Area, Zone, Conﬁguration, and User Module windows. Objects are always laid out in the Toolkit

window. Only the appropriate objects for each window are displayed. The blocks displayed at the

higher level of the Toolkit window in particular are called “components.” This refers to each type of

processor that operates the DME. “Object” normally refers to Picture, Text, Ellipse and other items

that are used after connecting them by wire to the various components.

Component Editor

The blocks that are arranged in the conﬁguration window are called “components.” Audio processors

like mixers, compressors, effects, and crossovers, along with parts like faders and meters, are used

for this purpose in the Conﬁguration window.

When you double-click on a component block arranged in the Conﬁguration window, the Component

Editor window will open. There you can edit the parameters for that component. The types of

parameters displayed will differ, depending on the component.

Component Editor

(Stereo Compressor)

Component

Chapter 2 DME Designer Overview

DME Designer Owner’s Manual

18

Resource Meter

This window provides an indication of the usage of the components in the conﬁguration window. The

usage percentage increases as the number of components increases, and is shown in graph form in

this window.

This window is shown at the same time as the designer window, and provides a guide when creating

conﬁgurations.

The usage percentage also depends on the sampling frequency at which the DME unit is set to

operate. Make sure that the usage percentage is kept below 100%.

Window Operations

Operations in all windows are the same as for normal Windows applications. The windows are

controlled with the [Minimize], [Maximize/Restore], and [Close] buttons at the upper right of the title

bar. DME Designer is closed by clicking the [Close] button on the Main Panel window.

Chapter 2 DME Designer Overview

DME Designer Owner’s Manual

19

Users and Security

You can create multiple users in DME Designer and set the functions that are available to each user.

Although users who will design and put together installations must be able to use all the functions of

DME Designer, users who will only operate the system can be restricted to functions that will not allow

them to accidentally change the settings.

DME Designer is used with one user at a time logged on. To change the user, click the [File] menu →

[Log Off] command on the Main Panel window.

About Users

To use DME Designer, you must logon when you start the software. Except for the ﬁrst time the

software is started or when separate settings are made for the ﬁrst time, you can logon by specifying

the name and password for a user that has been set as the administrator. The administrator can build

the system as a whole, or apply function limitations that let other people edit. Administrators or other

people that can use DME Designer are called “users.” The user name for the currently logged on user

appears below [User] on the Main Panel window.

The default user, named [Administrator], is set to use all of the functions. Immediately after DME

Designer is installed, [Administrator] is the only user, and there is no password set.

Multiple users can be created. When the system administrator creates multiple users, restrictions can

be applied separately for each one of them. A user with restrictions applied can edit using only the

functions the administrator enables for him.

The place to create, setup, and delete users is the “Security” dialog box. See “Security (Creating

Users and Making User Settings)” on page 55.

Currently Logged On User Name

Chapter 2 DME Designer Overview

DME Designer Owner’s Manual

20

Logging On

The “Log On” dialog box is displayed whenever the application is started or a user is logged off.

Whenever one user is already logged on, another user cannot be logged on. To log on as another

user, ﬁrst log off the currently logged on user.

■ The “Log On” dialog box

1 [User]

From the list, select the user you want to log on as.

2 [Password] Box

Enter the password.

3 [OK] Button

Log on as the selected user.

4 [Exit] Button

When the application is started, and the “Log On” dialog box is displayed, there is an [Exit]

button. This closes the application without logging on a user.

5 [Cancel] Button

When the “Log On” dialog box is displayed after a user is logged off, there is a [Cancel] button

instead of an [Exit] button. This cancels the logoff. The original user will continue to be logged

on.

■ Logon Procedure

1 Click [▼] at the right of the [User].

A drop-down list of user names will be displayed.

2 Click the user you want to log on.

3 Enter the password into the [Password] box.

When you type in the password box, the characters you enter will display as asterisks (*).

4 Click the [OK] button.

NOTE

If the automatic logon feature is enabled, the “Log On” dialog box will not be displayed when the application is started.

Instead, the auto-logon user will be logged on automatically.

1

2

3

5

Страница загружается...

Yamaha V1 Инструкция по применению

Похожие модели бренда

Модели других брендов