Yamaha DVD-S2500 Инструкция по применению

Yamaha
Бренд
Yamaha
Модель
DVD-S2500
Категория
Проигрыватели DVD
Тип
Инструкция по применению
DVD AUDIO/VIDEO SA-CD PLAYER
LECTEUR DE DVD AUDIO/VIDEO SA-CD
DVD-S2500
OWNER’S MANUAL
MODE D’EMPLOI
U
i
IMPORTANT SAFETY INSTRUCTIONS
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1 Read Instructions — All the safety and operating instructions
should be read before the product is operated.
2 Retain Instructions — The safety and operating instructions should
be retained for future reference.
3 Heed Warnings — All warnings on the product and in the operating
instructions should be adhered to.
4 Follow Instructions — All operating and use instructions should be
followed.
5 Cleaning — Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
6 Attachments — Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7 Water and Moisture — Do not use this product near water — for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub;
in a wet basement; or near a swimming pool; and the like.
8 Accessories — Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious
injury to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product.
Any mounting of the product should follow the manufacturer’s
instructions, and should use a mounting accessory recommended
by the manufacturer.
9 A product and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combination
to overturn.
10 Ventilation — Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these openings must
not be blocked or covered. The openings should never be blocked
by placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11 Power Sources — This product should be operated only from the
type of power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult your product
dealer or local power company. For products intended to operate
from battery power, or other sources, refer to the operating
instructions.
12 Grounding or Polarization — This product may be equipped with a
polarized alternating current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only
one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
13 Power-Cord Protection — Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the
product.
14 Lightning — For added protection for this product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product
due to lightning and power-line surges.
15 Power Lines — An outside antenna system should not be located in
the vicinity of overhead power lines or other electric light or power
circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken
to keep from touching such power lines or circuits as contact with
them might be fatal.
16 Overloading — Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire or
electric shock.
17 Object and Liquid Entry — Never push objects of any kind into this
product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
18 Servicing — Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service personnel.
19 Damage Requiring Service — Unplug this product from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way,
and
f) When the product exhibits a distinct change in performance
- this indicates a need for service.
20 Replacement Parts — When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or
other hazards.
21 Safety Check — Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
22 Wall or Ceiling Mounting — The unit should be mounted to a wall
or ceiling only as recommended by the manufacturer.
23 Heat — The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
ii
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion - and, most
importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices.
Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment
will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other
electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this
product is found to be the source of interference, which can be determined by turning the product “OFF” and “ON”, please try to
eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-
in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6660 Orangethorpe Ave. Buena Park,
CA90622.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
le laser
CAUTION
- Visible and invisib
radiation when open. Avoid exposure to beam.
For Customer Use:
Read carefully the information located at the rear panel of the
player and enter below the Serial No. Retain this information for
future reference.
Model No.
Serial No. __________________________
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot
and fully insert.
This Class B digital apparatus complies with Canadian ICES-003.
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus as set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
CAUTION
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
POUR LES CONSOMMATEURS CANADIENS
Pour éviter les chocs électriques, introduire la lame la plus large de
la fiche dans la borne correspondante de la prise et pousser
jusqu’au fond.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
iii
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this sound system in a well ventilated, cool, dry,
clean place — away from direct sunlight, heat sources,
vibration, dust, moisture, or cold. In a cabinet, allow
about 2.5cm (1 inch) of free space all around this unit
for adequate ventilation.
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, nor locate this unit in an environment
with high humidity (i.e., a room with a humidifier) to
prevent condensation inside this unit, which may cause
an electrical shock, fire, damage to this unit, and/or
personal injury.
5 Avoid installing this unit in a location where foreign
objects may fall onto this unit or where this unit may be
exposed to liquid dripping or splashing. On the top of
this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e., candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall,
spilling the liquid and causing an electrical shock to
the user and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9
Do not use excessive force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using this
unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or
personal injury. YAMAHA will not be held responsible
for any damage resulting from use of this unit with a
voltage other than as specified.
13 To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be opened
for any reason.
15 When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set
the unit in standby mode, then disconnect the AC
power plug from the wall outlet.
18 Place this unit on a flat, hard and stable surface.
19 There must be sufficient room in front of the player for
the disc tray to be opened.
20 The mechanical parts of the set contain self-lubricating
bearings and must not be oiled or lubricated.
NOTE:
Pictures shown maybe different between countries.
Never make or change connections with the power switched
on.
When playing DTS encoded CDs, excessive noise will be
heard from the analog stereo outputs. To avoid possible
damage to the audio system, the consumer should take
proper precautions when the analog stereo outputs of the
player are connected to an amplification system. To enjoy
DTS Digital Surround™ playback, an external 5.1-channel
DTS Digital Surround™ decoder system must be connected
to the digital output of the player.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only
a qualified service person should remove the cover or
attempt to service this device.
CAUTION
VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN. AVOID EXPOSURE TO BEAM.
DANGER
This unit emits visible laser radiation when open. Avoid
direct eye exposure to beam.
When this unit is plugged into a wall outlet, do not place
your eyes close to the opening of the disc tray and other
openings or look inside.
The unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off. This state is called the standby
mode. In this state, this unit is designed to consume a
very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
LASER DIODE PROPERTIES
Type Semiconductor laser GaAlAs
Wave length 650 nm (DVD/SA-CD)
790 nm (VCD/CD)
Output Power 7 mW (DVD/SA-CD/VCD/CD)
1
English
Patent information............................................................2
Playable disc formats .......................................................2
Region management information.....................................3
Supplied accessories ........................................................3
Installing batteries in the remote control .........................3
Using the remote control..................................................4
Maintenance.....................................................................4
Front panel .......................................................................5
Rear panel ........................................................................6
Remote control connectors and RS-232C terminal .........6
Remote control.................................................................7
Audio connection.............................................................8
Digital audio connections .................................................8
i.LINK components connections ......................................8
Analog audio (6CH DISCRETE) connection...................8
Analog audio (MIXED 2CH) connection.........................9
Video connections............................................................9
HDMI component connections.........................................9
Switching on ..................................................................10
Setups before the initial playback..................................10
General operation...........................................................12
Preferences.....................................................................12
Features...........................................................................12
Adv.Picture .....................................................................12
Picture .............................................................................13
Sound ..............................................................................13
Toolbar...........................................................................14
Program...........................................................................14
View................................................................................14
Play option ......................................................................14
Search..............................................................................14
Slide Show ......................................................................15
Setup ..............................................................................15
Access .............................................................................15
Features...........................................................................15
TV ...................................................................................15
Audio Menu ....................................................................16
Language.........................................................................17
Speakers ..........................................................................17
DVD/CD Mode...............................................................18
SA-CD Mode ..................................................................18
i.LINK.............................................................................18
Basic playback ...............................................................20
DVD-Video and DVD-Audio ........................................20
Playing a disc ..................................................................20
Smart Resume .................................................................20
DVD features.................................................................21
Menu............................................................................... 21
Camera angle .................................................................. 21
Changing the audio language and format....................... 21
Subtitle language ............................................................ 21
DVD-Audio features ..................................................... 21
Changing pages .............................................................. 21
Playing bonus groups ..................................................... 21
DVD Video Mode .......................................................... 21
SA-CD (Super Audio CD)............................................. 22
Playing a disc.................................................................. 22
Sound mode – SA-CD playback..................................... 22
Audio CD.......................................................................23
Playing a disc.................................................................. 23
Video CD and Super Video CD ....................................23
Playing a disc.................................................................. 23
Playback Control (PBC)................................................. 23
MP3 ...............................................................................24
MP3 disc features ........................................................... 24
Playing a disc.................................................................. 24
Choosing an Album/Track to playback.......................... 24
MP3 text ......................................................................... 24
JPEG ..............................................................................25
JPEG disc features.......................................................... 25
Playing a disc.................................................................. 25
Slide show setting........................................................... 25
Rotating the image.......................................................... 25
General features.............................................................26
Moving to another segment............................................ 26
Search ............................................................................. 26
Slow motion.................................................................... 26
Still picture and frame-by-frame playback..................... 26
Time search .................................................................... 26
Repeat ............................................................................. 27
Repeat A-B .................................................................... 27
Shuffle ............................................................................ 27
Scan ............................................................................... 27
Zoom .............................................................................. 27
FTS video/audio program............................................... 28
Activating/deactivating the FTS program ...................... 28
Erasing a track/chapter/index from the FTS list............. 28
Erasing all tracks/chapters/indexes from the FTS list .... 28
Disc lock ....................................................................... 28
Activating/deactivating Disc lock .................................. 28
Authorizing discs............................................................ 28
Deauthorizing discs ........................................................ 29
Parental Control ............................................................29
Activating/deactivating Parental Control ....................... 29
Country ........................................................................... 29
Changing the four-digit PIN..........................................29
If you forget your four-digit code................................... 29
Introduction 2
Functional Overview 5
Preparation 8
On-screen menu 12
Operation 20
Troubleshooting 30
Specifications 31
Table of Contents
2
Introduction
Thank you for purchasing the YAMAHA DVD
AUDIO/VIDEO SA-CD player. This Owner’s Manual
explains its basic operations.
Manufactured under license from
Dolby Laboratories.
“Dolby”, “Pro Logic”, and the
double-D symbol are trademarks of
Dolby Laboratories.
“DTS” and “DTS Digital Surround”
are registered trademarks of Digital
Theater Systems, Inc.
“DCDi” is a trademark of Faroudja, a
division of Genesis Microchip, Inc.
HDMI, the HDMI logo and High-
Definition Multimedia Interface are
trademarks or registered trademark of
HDMI Licensing LLC.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
“i.LINK” and the “i.LINK” logo are trademarks of
Sony Corporation.
This product complies with the following i.LINK
interface specifications:
1. IEEE Std 1394a-2000, Standard for a High
Performance Serial Bus
2. Audio and Music Data Transmission Protocol 2.1
Following the standard for AM824 sequence adaptation
layers, the product is compatible with IEC60958
bitstream, DVD-A and SA-CD media.
This unit can play the disc types associated with the
logos shown below. (Do not attempt to load any other
type of disc into the unit, or the unit may be damaged.)
This manual refers to disc types using the following
symbols:
*1 icon includes Super Video CD.
Notes:
– This unit is designed for use with SA-CD, DVD-
Video, DVD-Audio, Video CD, Super Video CD,
Audio CD, CD-R and CD-RW (MP3 and JPEG
supported), DVD+R and DVD+RW, DVD-R and
DVD-RW.
– CD-R and CD-RW discs cannot be played unless they
have been finalized.
– DVD+R and DVD+RW discs cannot be played
unless they have been finalized.
– DVD-R and DVD-RW discs must be recorded in
Video format and must be finalized.
– Some discs cannot be played depending on disc
characteristics or recording conditions.
– Be sure to use only CD-R and CD-RW discs from
reliable manufacturers.
– Dolby Digital, DTS Digital Surround, and MPEG
digital audio are supported.
– PAL and NTSC are supported.
– This unit features the PAL and NTSC video system
converting function to allow you watching the
different types of video discs on one TV (see “TV
System (NTSC/PAL conversion)” on page 15).
– Do not use any non-standard shaped discs (heart,
etc.).
– Do not use discs that have tape, scales, or paste on
them or damage to the unit may result.
– Do not use discs with surfaces printed by a
commercial label printer.
– Some DVD discs require specific features or allow
only limited function during playback.
– Prohibited mark may appear on the TV screen to
indicate that a function is unavailable.
– Photo CD, CD-ROM, DVD-ROM, DVD-RAM, CDV
and nonstandard CD discs cannot be played on this
unit.
Patent information
Playable disc formats
DI
G
I
T
A
L
VIDE
O
SUPER VIDE
O
DVD-Audio DVD-Video Video CD
*1
SA-CD
(Super Audio CD)
Audio CD MP3
DVD-A
DVD-V
VCD
SA-CD
CD
MP3
VCD
3
English
Introduction
The unit is designed to support the Region Management
System. Check the regional code number on the disc
package. If the number does not match the unit’s region
number (see table below, or see back of unit), the unit
may be unable to play the disc.
Check your package to make sure it contains the
following items:
Insert the batteries in the correct direction by aligning
the “+” and “–” marks on the batteries with the polarity
markings “+” and “–” inside the battery compartment.
1 Remove the back cover.
2 Insert the two supplied batteries (AA, R6, UM-3) into
the battery compartment.
3 Close the back cover.
Replace worn batteries
Worn batteries limit the operating range of the remote
control. Replace both batteries at the same time.
• Replace both batteries if you notice a decrease in the
operating range of the remote control.
• Do not use old batteries with new ones.
• Do not use different types of batteries (such as
alkaline and manganese) together. Read the battery
packaging carefully. Different types of batteries may
be the same shape or color.
• If the batteries leak, dispose of them immediately.
Avoid touching the leaked material or letting it come
into contact with clothing, etc. Clean the battery
compartment thoroughly before installing new
batteries.
Region management
information
Model
Region
number of
the unit
Discs that can be
played (Example)
U.S.A. model
U.K. and
Europe models
Supplied accessories
1 1
ALL
2 2
ALL
Remote control Batteries (x2) (AA, R6, UM-3)
Audio/Video cable Power cable
Installing batteries in the
remote control
4
Introduction
Handling the remote control
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– high humidity such as near a bath
– high temperature such as near a heater or stove
– extremely low temperature
– dusty places
Cleaning the cabinet
• Use a soft cloth slightly moistened with a mild detergent
solution. Do not use a solution that contains alcohol,
spirits, ammonia or abrasives.
Cleaning discs
• When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe in
a circular motion.
• Do not use solvents such as benzene, thinner,
commercial cleaners, or anti-static spray designed for
analog records.
Using the remote control
Maintenance
30
30
Point the remote control at the
sensor, within approximately 6 m
(20 feet) of the unit.
Remote control
sensor
5
English
Functional Overview
Front panel
STANDBY/ON
–turns on this unit or sets it to the
standby mode
Disc tray
b
–moves to the previous chapter or track
a
–moves to the next chapter or track
s STOP
– stops playback
e PAUSE
– pauses playback
p PLAY
– starts playback
DVD-AUDIO indicator
–lights up when the unit detects DVD-Audio
signals
SA-CD indicator
–lights up when the unit detects SA-CD signals
MULTI CH indicator
–lights up when you play multi-channel audio
source
HDMI indicator
–lights up when the unit is capable of outputting
signals from the HDMI (High Definition
Multimedia Interface) terminal
i.LINK indicator
–lights up when an AV receiver selects i.LINK
(IEEE1394)
Front panel display
– shows information about the
operational status of the unit
PROGRESSIVE indicator
– lights up when the unit enters
PROGRESSIVE mode
AUDIO DIRECT indicator
– lights up when you enter the AUDIO
DIRECT mode by pressing the AUDIO
DIRECT button on the remote control
during audio disc playback
DOWN MIX indicator
– lights up when you play the discs that
allow down mixing of the multi-channel
audio sources
OPEN/CLOSE
– opens or closes the disc tray
6
Functional Overview
Remote control connectors are used in custom installations to transmit remote control signals via cable.
• Connect REMOTE CONTROL IN to an output on your remote control system.
• Connect REMOTE CONTROL OUT to a remote control input on another component to enable system control.
This unit is also equipped with RS-232C terminal. Consult your dealer for details.
Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause
permanent damage to the unit.
Rear panel
HDMI output terminal
–connect to the HDMI jack on a
HDMI-compatible AV component
SCAN MODE switch
–switches the component video output
signals between progressive and
interlace
COMPONENT video jacks
–connect to an AV receiver with Y P
B
P
R inputs
RS-232C terminal
– use as an expansion terminal for commercial use
Consult your dealer for details
REMOTE CONTROL connectors
– use in custom installations to transmit remote
control signals via cable connections
i.LINK connectors
– connect to the i.LINK jack on an
i.LINK-compatible component
COAXIAL digital audio output
–connect to the audio input jack on
digital (coaxial) audio equipment
S VIDEO output
–connect to an S-Video input jack on
your AV receiver
VIDEO output (composite video
out)
–connect to the video input jack on your
AV receiver
OPTICAL digital audio output jack
– connect to the audio input jack on digital
(optical) audio equipment
MIXED 2CH audio output jacks
– connect to audio inputs on your AV receiver
or stereo system
6CH DISCRETE audio output jacks
– connect to an AV receiver with 6-ch discrete
audio input jacks
AC IN (Main-inlet)
– connect to a standard AC outlet
Remote control connectors
and RS-232C terminal
7
English
Functional Overview
* Press and hold button for about two seconds.
Remote control
– turns the power of this unit ON or
enters standby mode
0-9 numeric buttons
SUBTITLE
– selects subtitle languages
AUDIO
– selects audio languages and formats
ANGLE
– selects DVD camera angles
ZOOM
– enlarges video images
RETURN/RESUME
– displays the previous menu or
resumes playback
knlh
– (left/right/up/down) selects an item
in the menu
ENTER/OK
– acknowledges menu selection
MENU
– accesses the menu of a DVD disc
b
– searches backward*/accesses a
previous chapter or track
a
– searches forward*/accesses the
next chapter or track
DIMMER
–adjusts the display brightness
AUDIO DIRECT
–switches video output on and off
during audio disc playback
SOUND MODE
–selects the required sound mode
• for SA-CD: CD, Stereo, or Multi-
channel (if available)
• for DVD/VCD: Stereo, Dolby
Surround compatible, 3D sound, or
Multi-channel
PAGE
–turns pages of the DVD-Audio still
pictures
TITLE/CHAP
–selects title or chapter
STATUS
– displays current playback information
on the front panel display and on the
status window on screen
ON SCREEN
–accesses or removes the player’s On-
screen menu
STOP (s)
–stops playback
PLAY (p)
–starts playback
PAUSE (e)
–pauses playback temporarily/
frame-by-frame playback
SCAN
–plays the first 10 seconds of each
track/chapter within a disc
REPEAT
–repeats chapter, track, title, disc, etc.
A-B
–repeats a specific segment
SHUFFLE
–plays tracks/chapter in random order
PROG
–turns program playback on or off
• available only when a programmed
playlist has been created
8
Preparation
• There are various ways to connect the player, depending
on the equipment you wish to use. The following
drawings illustrate some possible configurations.
• Please refer to manuals for other equipment as necessary
to ensure that you make the correct connections.
• Do not connect the player via your VCR. The video
quality could be distorted by the copy protection system.
• Do not connect the player’s audio output jack to the
phono input jack on your audio system.
Digital audio connections
This unit features COAXIAL and OPTICAL digital
output jacks. Connect one or both of them to digital
input jacks of an AV receiver. You can also enjoy high-
quality stereo sound at sampling frequencies of 88.2 and
96 kHz, assuming the material is not copy-protected and
the equipment you connect is compatible with these
signals.
Notes:
– If the audio format of the digital output does not
match the capabilities of your receiver, the receiver
will produce a strong, distorted sound or no sound at
all. Make sure to select the appropriate audio format
on the disc menu screen. Pressing AUDIO once or
more may change not only the audio language but
also the audio format. The selected format name will
be displayed for several seconds in the status
window.
– SA-CD audio signal is not output from DIGITAL
OUT jacks.
– If you wish to enjoy Dolby Digital, DTS, and MPEG
you must connect this unit to the AV receiver that
support those.
i.LINK components connections
Use an i.LINK connection cable of approximately
3m (10 feet) or less to connect this unit to i.LINK-
compatible components (refer to page 18 for details).
Analog audio (6CH DISCRETE)
connection
Connect a receiver with multi-channel audio input
terminals to enjoy surround sound with no sampling
frequency limitation. We recommend this connection to
obtain maximum performance of SA-CD discs and
DVD-Audio multi-channel sound.
Audio connection
COAXIAL
IN
OPTICAL
IN
AV receiver
Insert
fully, with
this side
facing up.
RL
FRONT
RL
SURROUND
CENTER
SUBWOOFER
AV receiver
9
English
Preparation
Analog audio (MIXED 2CH)
connection
Use the audio cable supplied with the player to connect
AUDIO OUT L (left) and R (right) jacks of the player to
the corresponding input jacks on your audio equipment,
such as an AV receiver.
If your AV receiver features video output jacks, connect
this unit to the AV receiver (and then to your TV). This
enables you to use one TV for several different video
sources (LD, VCR etc.) by simply switching the input
source selector on your AV receiver.
This unit features three types of video output jacks
(Component, Video and S-Video). Connect the
appropriate video output jack to your equipment.
HDMI component connections
Use the HDMI connection cable to connect this unit to
HDMI-compatible components.
Note:
– You can use a HDMI to DVI conversion cable to
connect this unit to DVI HDCP compatible
components. In this case, no audio signals are output
from this unit’s jacks.
Video connections
DVD/CD
R L
AV receiver
COMPONENT IN
S VIDEO
IN
VIDEO
IN
YPB/CB PR/CR
VIDEO
OUT
VIDEO
IN
S VIDEO OUT
S VIDEO
IN
COMPONENT IN
COMPONENT OUT
Y
P
B/CB PR/CR
Y
P
B/CB
PR/CR
AV receiver
TV
S VIDEO
IN
VIDEO
IN
COMPONENT IN
SUB
Projector
10
Preparation
SCAN MODE selector
This selector switches the type of output signal from the
COMPONENT video jacks on this unit.
INTERLACE:
Select INTERLACE if you are connecting the
component to a standard (interlace format) TV.
PROGRESSIVE:
Select PROGRESSIVE if your TV accepts NTSC
progressive or PAL progressive signals. This setting
will enable you to enjoy accurate color reproduction and
high quality images. This unit features DCDi circuit.
The PROGRESSIVE indicator on the front panel lights
up during progressive playback.
Notes:
– In the PROGRESSIVE mode, 4:3 aspect images are
stretched horizontally on the wide screen TV. We
recommend to change the TV screen’s aspect ratio
settings for progressive signals if you wish to watch
the original aspect ratio images without distortion.
You can also change the aspect ratio settings in the
[4:3 Aspect] parameter in the On-screen menu.
– Some TVs and projectors are not compatible with this
unit. If you notice picture distortion when outputting
the progressive signals, switch the SCAN MODE
selector to INTERLACE.
1 Connect the AC power cord to the power outlet.
2 Switch on the TV and this unit.
3 Set the TV to the correct Video IN channel. (e.g. EXT1,
EXT2, AV1, AV2, AUDIO/VIDEO, etc. Refer to your
TV owner’s manual for detail.)
➜ The front panel display lights up and the default
screen appears on the TV.
4 If you are using an external equipment (e.g. audio
system or receiver), turn them on and select the
appropriate input source that was used to connect to this
unit. Refer to the equipment owner’s manual for detail.
Note:
– If you do not have a proper picture or sound, refer to
“Troubleshooting” section.
We recommend to setup some of the basic menu items
before the initial playback.
1 Press STANDBY/ON to turn on the unit.
2 Press ON SCREEN.
➜ On-screen menu is displayed on the screen.
3 Follow the procedure described below to set the
following menu items.
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE
USER SWITCH THE CONNECTION TO THE
“STANDARD DEFINITION” OUTPUT. IF THERE
ARE QUESTIONS REGARDING OUR VIDEO
MONITOR COMPATIBILITY WITH THIS
MODEL 525P AND 625P DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.
This unit is compatible with the complete line of
YAMAHA products, including the projectors
DPX-1000, DPX-1100, LPX-500, LPX-510, the
plasma monitor PDM-1 and PDM-4210.
Switching on
Setups before the initial
playback
ON SCREEN
11
English
Preparation
1Menu Language (see page 17)
You can select the language displayed in the On-screen
menu.
1 Go to [Menu Language] (Setup ➔ Language ➔ Menu
Language) by using knlh buttons on the remote
control, then press h.
➜ Choices are displayed on the right column.
2 Select a language to be displayed in the On-screen menu
by using kn buttons.
3 Press l to return to the previous menu.
2Default Audio (see page 17)
You can select the audio language spoken in video discs.
Available choices are determined by the disc.
1 Go to [Default Audio] (Setup ➔ Language ➔ Default
Audio) by using knlh buttons on the remote
control, then press h.
➜ Choices are displayed on the right column.
2 Select a language by using kn buttons.
3 Press l to return to the previous menu.
3Default Sub-title (see page 17)
You can select the subtitle language set as default.
Available choices are determined by the disc.
1 Go to [Default Sub-title] (Setup ➔ Language ➔ Default
sub-title) by using knlh buttons on the remote
control, then press h.
➜ Choices are displayed on the right column.
2 Select a default subtitle language by using kn buttons.
3 Press l to return to the previous menu.
4TV shape (see page 15)
You can select the aspect ratio of the video displayed on
the TV monitor.
Select [Widescreen] if you connect to a wide-screen
monitor. If you connect to a conventional monitor,
select [4:3 panscan] (the left and right sides are trimmed
when you play 16:9 video) or [4:3 letterbox] (black
areas appear at the top and bottom when you play 16:9
video).
1 Go to [TV shape] (Setup ➔ TV ➔ TV shape) by using
knlh buttons on the remote control, then press h.
➜ Choices are displayed on the right column.
2 Make a choice by using kn buttons.
3 Press l to return to the previous menu.
5Analog output (see page 16)
Enables you to specify the type of analog output suitable
for your AV receiver. Select [Multi-channel] if you are
using a multi-channel AV receiver with 6-ch discrete
inputs. If your AV receiver does not have 6-ch discrete
inputs, select one of [Stereo], [Dolby Surr Compat], or
[3D sound].
1 Go to [Analog output] (Setup ➔ Audio Menu ➔ Analog
output) by using knlh buttons on the remote
control, then press h.
➜ Choices are displayed on the right column.
2 Select an item for the analog output signal by using kn
buttons.
3 Press l to return to the previous menu.
6Digital output (see page 16)
Enables you to specify the type of digital output suitable
for your AV receiver. Select [PCM only] if your AV
receiver is not capable of decoding multi-channel audio.
Select [All] if you connected this unit’s digital out jacks
to a multi-channel AV receiver.
1 Go to [Digital output] (Setup ➔ Audio Menu ➔ Digital
output) by using knlh buttons on the remote
control, then press h.
➜ Choices are displayed on the right column.
2 Select an item for the digital output signal by using kn
buttons.
3 Press l to return to the previous menu.
Notes:
– Press ON SCREEN again to exit from the On-screen
menu.
– You can find the selection of the helpful menu items
in [Preference] and [Setup].
Go to [Preference] if you want to customize this unit
for your personal requirement such as the Wake-up
timer.
Go to [Setup] if you want to set the operational status
of this unit.
12
On-screen menu
The On-screen menu enables you to customize this unit
to suit your requirements.
1 Press ON SCREEN on the remote control.
➜ The On-screen menu appears on the screen.
2 Press knlh to navigate the On-screen menu and to
change the settings.
3 Press ON SCREEN to exit from the On-screen menu.
Features
Dimmer
Adjusts the brightness of the front panel display.
You can use this function if the brightness of the front
panel display disturbs your enjoyment of the home
theater.
Choices: Low, Medium, Normal
Initial setting: Normal
Wake up timer
Turns on the player from standby mode after a preset
amount of time. The timer is then reset to zero. You can
set the timer for up to 600 minutes.
Choices: 0 to 600 minutes
Initial setting: 0
Status window
Displays the current status of the player. Select [Off] to
suppress display of the Status window.
Choices: On, Off
Initial setting: On
Adv.Picture
Allows you to fine-tune the following video parameters.
4:3 Aspect
You can adjust the aspect ratio of the projected images
on the screen. This function is only available for
progressive scan and HDMI video output.
Select [NL_Stretch] for display of 4:3 image on the 16:9
screen with non-linear stretching (Center position of
screen is stretch less than the side).
Select [4:3 PillarBox] to display 4:3 image on the 16:9
screen without stretching. Even when playing a disc
recorded in the 16:9 squeeze mode, the picture is
displayed in the center of the screen.
No aspect ratio adjustment is made when [Auto] is
selected.
We recommend setting the aspect ratio on your TV if the
function is available.
Choices: 4:3 PillarBox, NL_Stretch, Auto
Initial setting: Auto
TrueLife
Produces more dynamic picture by increasing the
picture contrast and the color intensity. This function is
available for progressive scan output only.
Choices: 0 to +7
Initial setting: 0
DCDi
DCDi (Directional Correction Deinterlacing) computes
and tracks the angle of the screen edge to fill in the
missing pixel on the TV screen. DCDi will optimize the
image quality significantly, especially during the slow
motion playback. This function is available for
progressive scan output only.
Choices: On, Off
Initial setting: On
Chroma Delay
The chroma (color) and luminance (brightness) signals
are not synchronized. The Chroma Delay setting allows
you to adjust the advance delay of the chroma signal to
yield a perfectly clear picture. This function is available
for signals output from COMPONENT video jacks
only.
Choices: –3 to +3
Initial setting: 0
Gamma
Enables you to adjust the intensity of the picture non-
linearly. A positive value enables you to bring out low
level detail in dark scenes, while a negative value
emphasizes contrast. This function is available for
signals output from COMPONENT video jacks only.
Choices: –7 to +7
Initial setting: 0
General operation
Preferences
Preferences
Toolbar
Setup
Toolbar
Program
View
Play Option
Search
Slide Show
13
English
On-screen menu
HDMI Video
Enables you to adjust the resolution depending on the
monitor you are using. You can use this function only
when the HDMI output terminal is connected to a
HDMI-compatible component.
Choices: 480p, 576p, 720p, 1080i, Auto
Initial setting: 480p
Setting Examples
*: Refer to the instruction manual of the monitor and
choose an appropriate aspect ratio.
*1: The HDMI video output may not be displayed
properly if the HDMI-compatible monitor you are using
does not support the selected resolution setting.
To return to the initial setting, you must first stop
playback and eject the disc, then press “PLAY” ➔ “0”
➔ “2” ➔ “9” ➔ “STOP” on the remote control.
*2: If the desired aspect ratio is not available, select the
most suitable setting from [AUTO], [4:3 PillarBox] and
[NL_Stretch].
Notes:
– While HDMI video signals are being output,
component video output is unavailable.
– When a video setting is modified, the picture may not
be displayed for several seconds.
– When the image conversion (PAL ↔ NTSC) begins,
the picture may not be displayed for several seconds.
Picture
Video shift
Adjusts the position of the image on the screen by
scrolling it to the left or right.
Choices: +1 to +7
Initial setting: +4
Saturation
Adjusts the video color saturation. This function is not
available for signals output from COMPONENT video
jacks and HDMI video signals.
Choices: –7 to +7
Initial setting: 0
Contrast
Accentuates bright and dark parts of the video. This
function is not available for signals output from
COMPONENT video jacks and HDMI video signals.
Choices: –7 to +7
Initial setting: 0
Picture Mode
Adjusts the color tone to suit your preference and the
playing source. [Personal] will be chosen automatically
when you change the value in the following menus:
[Saturation], [Contrast], [Brightness], and [Sharpness].
This function is not available for signals output from
COMPONENT video jacks and HDMI video signals.
Choices: Rich, Natural, Soft, Animation, Personal
Initial setting: Natural
Brightness
Adjusts the overall brightness of the picture. This
function is not available for signals output from
COMPONENT video jacks and HDMI video signals.
Choices: –7 to +7
Initial setting: 0
Sharpness
Adjusts the sharpness of the video.
Choices: 0 to +7
Initial setting: 0
Sound
Karaoke vocal
Enables you to play multi-channel karaoke DVDs. The
karaoke channels on the disc will be mixed into normal
stereo when you choose [On].
Choices: On, Off
Initial setting: Off
ClearVoice
Increases the relative volume of dialog for easy listening
at night. This function is available for only certain multi-
channel discs.
Choices: On, Off
Initial setting: Off
HDMI Video Functions
480p
Select the desired resolution for the
monitor you are using. *1
576p
720p
1080i
Auto
The resolution is automatically selected
to match the monitor you are using.
Monitor
shape
Playback
disc
TV shape 4:3 aspect
16:9
(Projector)
Squeezed 16:9
video
Widescreen Auto
4:3 video Widescreen
4:3 PillarBox
*2
4:3
Squeezed 16:9
video
4:3 panscan
or
4:3 letterbox
–
4:3 video
4:3 panscan
or
4:3 letterbox
–
14
On-screen menu
Night mode
When set to [On], the dynamics of the sound output is
optimized. High volume output is softened, enabling
you to watch your favorite action movie without
disturbing others.
Choices: On, Off
Initial setting: Off
Program
You can create your own playlist using this menu. First,
go to [Tracks], then select the tracks/chapters, etc. to
include in your playlist. The programmed playlist will
be activated when you choose [On] in the [Program]
menu.
Clear all
Deletes all Programmed contents.
Program
Set the FTS program playback on or off.
Choices: On, Off
Initial setting: Off
Tracks
Selects tracks and chapters for your FTS list.
Playlist
Shows the programmed FTS list.
Note:
– For details about FTS and the settings of [Program]
menu items, see the descriptions followed by “FTS
video/audio program” on page 28.
View
Rotate
Rotates a JPEG image.
Choices: –180°, –90°, 0, +90°, +180°
Initial setting: 0
Zoom
Activates the zoom function. A cursor will be displayed
on screen. Move the cursor using the knlh buttons,
then select a size by pressing the ENTER button
repeatedly. To exit zoom mode, press RETURN/
RESUME repeatedly until the cursor disappears from
the screen.
Chapter preview
Plays the first 10 seconds of each chapter/track on the
disc. Pressing SCAN on the remote control performs the
same function as well.
Choices: On, Off
Initial setting: Off
Angle
Some DVD discs feature a multiple angle function,
enabling you to watch certain scenes from various
angles. Function availability and the number of camera
angles vary according to the disc.
Page
Turns pages of DVD-Audio still images.
Play option
DVD Video Mode
Some DVD-Audio discs include DVD-Video contents
that can be played on conventional DVD-Video players.
To play such contents, select [On]. The setting returns to
[Off] when you eject a disc or turn the unit to standby
mode.
Choices: On, Off
Initial setting: Off
Audio
Selects the sound format and audio language. Available
choices are determined by the disc.
Disc Navigation
You can direct to a track, etc. by using this menu.
Subtitle
Selects the subtitle language. Available choices are
determined by the disc.
Search
Frame by Frame
Advances or reverses one frame at a time. This function
is available for video discs only. Previous frame is not
available for VCD and SVCD.
Fast
Selects a speed for fast forward or fast reverse playback.
Choices: –32, –8, –4, +1, +4, +8, +32
Initial setting: +1
Time
You can move to a certain spot by indicating the elapsed
time.
Slow
Selects a speed for the slow forward or slow reverse
playback.
Choices: –1, –1/2, –1/4, –1/8, 0, +1/8, +1/4, +1/2, +1
Initial setting: 0
Toolbar
15
English
On-screen menu
Slide Show
Use this feature for JPEG slide show playback.
Picture time
Sets the duration for each image.
Choices: Slow, Medium, Fast
Initial setting: Medium
Access
Disc lock
This function enables you to restrict others from
accessing certain discs.
If this setting is on, you need to enter the four-digit PIN
to modify the [Access] menu settings before you can
play the disc.
Choices: On, Off
Initial setting: Off
Change PIN
Enables you to change the four-digit PIN.
To change the four-digit PIN, enter the current PIN first,
then enter the new four-digit PIN.
Enter PIN
Enter the four-digit PIN to unlock the disc or to display
the [Access] menu.
Parental level
DVD movies may contain scenes that are unsuitable for
children. Therefore, some discs contain parental control
information that may apply to the entire disc or to
certain scenes. Ratings are country-specific. You can
specify a country code in the On-screen menu (Setup ➔
Language ➔ Country). See “Country” on page 29.
Choices: 0 to 8
Initial setting: 0
Country
Selects a country to apply its rating system to Parental
Level control.
Features
PBC
A VCD menu screen is displayed when this setting is on.
Choices: On, Off
Initial setting: On
Sleeptimer
Places this unit in standby mode when playback is
stopped and this unit is not operate for 20 minutes.
Choices: On, Off
Initial setting: Off
TV
TV shape
If you connect to a conventional 4:3 aspect TV, select
[4:3 panscan] (the left and right sides are trimmed when
you play 16:9 video) or [4:3 letterbox] (black areas
appear at the top and bottom when you play 16:9 video).
Select [Widescreen] if you connect to a Wide-Screen
TV.
Choices: 4:3 panscan, 4:3 letterbox, Widescreen
Initial setting: 4:3 panscan
TV System (NTSC/PAL conversion)
Allows you to select [PAL], [NTSC] or [Auto] mode to
match your TV system. You can play PAL discs on
NTSC monitor, and NTSC discs on PAL monitor. The
initial setting is [NTSC].
Choices: PAL, NTSC, Auto
The following conversions are supported.
Notes:
– In progressive scan mode, the output signals from the
VIDEO and S VIDEO jacks are same as the format of
the disc you play.
– Some image distortion occurs when switching the
NTSC and PAL mode.
– If your TV does not accept the selected mode while
you change the [TV System] setting, the screen will
be distorted so that you cannot recognize the On-
screen menu. When it occurs, you can change the
[TV System] settings by the remote control
operations. Follow the procedures below.
• Choosing [PAL]:
Press “PLAY” ➔ “2” ➔ “5” ➔ “6” ➔ “PLAY”
on the remote control.
• Choosing [NTSC]:
Press “PLAY” ➔ “2” ➔ “5” ➔ “7” ➔ “PLAY”
on the remote control.
Do not perform this operation while playing back a
disc on this unit.
Setup
Disc
Format
Output format
Selected mode
NTSC PAL AUTO
NTSC NTSC PAL NTSC
PAL NTSC PAL PAL
Widescreen
4:3 letterbox
4:3 panscan
16
On-screen menu
Audio Menu
Digital output
Enables you to specify the type of digital output that best
suits your AV receiver or HDMI monitor/receiver.
Select [PCM only] if your receiver or HDMI monitor/
receiver is not capable of decoding multi-channel audio.
Select [All] if you connected this unit’s digital out jacks
to a multi-channel decoder/receiver.
Choices: Off, PCM only, All
Initial setting: All
Note:
– SA-CD audio signal is not output from DIGITAL
OUT jacks.
Analog output
Enables you to specify the type of analog output suitable
for your AV receiver.
Choices: Stereo, Dolby Surr Compat, 3D sound,
Multi-channel
Initial setting: Multi-channel
Stereo:
In this setting, the multi-channel audio is down-
mixed to a stereo signal. Select this setting when
connecting to a TV, stereo amplifier/receiver, etc.
Dolby Surr Compat:
Select this setting when using
equipment with a Dolby Surround Pro Logic decoder. In
this setting, the multi-channel audio (Dolby Digital,
MPEG-2, DTS) is downmixed to a Dolby Surround
compatible 2-ch output. SA-CD and PCM signals with
a sampling frequency of over 88.2 kHz are downmixed
to normal stereo.
3D sound:
In a setup without rear speakers (analogue
stereo output), 3D Sound remixes the six channels of
digital surround (except for SA-CD and PCM signals
with a sampling frequency of over 88.2 kHz) into a two
speaker output while retaining all of the original audio
information. The result is the sensation of being
surrounded by multiple speakers.
Multi-channel:
Select this setting when using a multi-
channel AV receiver with 6-ch discrete inputs. The
multi-channel audio signals those of like DVD-Audio,
DVD-Video, and SA-CD are output from the respective
6-ch discrete output jacks. In this mode, this unit will
perform DTS decoding, Dolby Digital 5.1-channel
decoding, or MPEG Multichannel decoding when
applicable, and Dolby Pro Logic II decoding on 2-ch
sound tracks except for SA-CD and PCM signals with a
sampling frequency of over 88.2 kHz.
PCM output
Enables you to select PCM digital output at 48 kHz or
96 kHz. If you select [48 KHz], PCM data will be
converted to 2-ch 48 kHz or less. Select [48 KHz] if the
connected equipment cannot process signals with a
sampling frequency of 96 kHz or 88.2 kHz.
Choices: 96 KHz, 48 KHz
Initial setting: 96 KHz
Notes:
– Signals are converted to either 48 kHz or 44.1 kHz
despite the above settings if the disc has copy
protection.
– If you select [96 KHz], signals with a sampling
frequency of over 96 kHz are converted to 2-ch
88.2 kHz or 96 kHz.
SA-CD Direct
Enables you (with a suitable speaker system) to bypass
the bass management system for multi-channel SA-CD
playback, so you can enjoy the pure SA-CD quality.
Choices: On, Off
Initial setting: Off
Note:
– When [SA-CD Direct] is [On], the speaker settings
will not be applied during SA-CD playback.
HDMI Audio
If you are not using HDMI audio output, you should set
this to [Off].
If the monitor/receiver connected to this unit using
HDMI does not support HDMI audio signal input, set
this to [Off].
Choices: On, Off
Initial setting: Off
Notes:
– Super Audio CD signals cannot be output using
HDMI.
– This unit can output the following audio signals using
HDMI: 32/44.1/48 kHz, 2-ch PCM signals and
bitstream signals (Dolby Digital, DTS and MPEG).
PCM signals with a sampling frequency of over
88.2 kHz are converted to 2-ch 48 kHz or 44.1 kHz.
– When audio signals are being output by a HDMI-
component, digital output signals are muted.
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Yamaha DVD-S2500 Инструкция по применению

Yamaha
Бренд
Yamaha
Модель
DVD-S2500
Категория
Проигрыватели DVD
Тип
Инструкция по применению
Скачать PDF
сообщить о нарушении

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ

на других языках

Похожие модели бренда

Модели других брендов