Sony DAV-SC6 Инструкция по эксплуатации

4-248-413-42(1)

Compact AV

System

Operating Instructions

Инструкции по эксплуатации

DAV-SC6

GB

RU

2

GB

3

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

Do not install the appliance in a confined space, such

as a bookcase or built-in cabinet.

To prevent fire, do not cover the ventilation of the

apparatus with news papers, table-cloths, curtains, etc.

And don’t place lighted candles on the apparatus.

To prevent fire or shock hazard, do not place objects

filled with liquids, such as vases, on the apparatus.

Don’t throw away the battery with

general house waste, dispose of it

correctly as chemical waste.

This appliance is

classified as a CLASS 1

LASER product. The

label is located on the

bottom of the unit.

Precautions

Safety

• If anything falls into the cabinet, unplug the unit and

have it checked by qualified personnel before

operating it any further.

• The unit is not disconnected from the AC power

source (mains) as long as it is connected to the mains

outlet, even if the unit itself has been turned off.

• Unplug the unit from the wall outlet if you do not

intend to use it for an extended period of time. To

disconnect the cord, pull it out by the plug, never by

the cord.

Installing

• Allow adequate air circulation to prevent internal

heat buildup.

• Do not place the unit on surfaces (rugs, blankets, etc.)

or near materials (curtains, draperies) that may block

the ventilation slots.

• Do not install the unit near heat sources such as

radiators, or air ducts, or in a place subject to direct

sunlight, excessive dust, mechanical vibration, or

shock.

• Do not install the unit in an inclined position. It is

designed to be operated in a horizontal position only.

• Keep the unit and discs away from equipment with

strong magnets, such as microwave ovens, or large

loudspeakers.

• Do not place heavy objects on the unit.

• If the unit is brought directly from a cold to a warm

location, moisture may condense inside the Compact

AV System and cause damage to the lenses. When

you first install the unit, or when you move it from a

cold to a warm location, wait for about 30 minutes

before operating the unit.

Thank you for purchasing Sony Compact AV

System. Before operating this system, please

read this manual thoroughly and retain it for

future reference.

WARNING

Welcome!

3

GB

On power sources

AC power cord must be changed only at the qualified

service shop.

On placement

• Place the system in a location with adequate

ventilation to prevent heat build-up in the system.

• At high volume, over long periods of time, the cabinet

becomes hot to the touch. This is not a malfunction.

However, touching the cabinet should be avoided. Do

not place the unit in a confined space where

ventilation is poor as this may cause overheating.

• Do not block the ventilation slots by putting anything

on the system. The system is equipped with a high

power amplifier. If the ventilation slots on the top

surface are blocked, the unit can overheat and

malfunction.

• Do not place the system on a soft surface such as a rug

that might block the ventilation holes on the bottom.

• Do not place the system in a location near heat

sources, or in a place subject to direct sunlight,

excessive dust, or mechanical shock.

On operation

• If the system is brought directly from a cold to a warm

location, or is placed in a very damp room, moisture

may condense on the lenses inside the system. Should

this occur, the system may not operate properly. In

this case, remove the disc and leave the system turned

on for about half an hour until the moisture

evaporates.

• When you move the system, take out any disc. If you

don’t, the disc may be damaged.

• For power saving purposes, the system can be

completely turned off by the "/1 button on the

system. Though the LED remains lit for a while, the

system is completely off.

On adjusting volume

Do not turn up the volume while listening to a section

with very low level inputs or no audio signals. If you

do, the speakers may be damaged when a peak level

section is suddenly played.

On cleaning

Clean the cabinet, panel, and controls with a soft cloth

slightly moistened with a mild detergent solution. Do

not use any type of abrasive pad, scouring powder or

solvent such as alcohol or benzine.

If you have any questions or problems concerning your

system, please consult your nearest Sony dealer.

On cleaning discs

Do not use a commercially available CD/DVD

cleaning disc. It may cause a malfunction.

On your TV’s colour

If the speakers should cause the TV screen to have

colour irregularity, turn off the TV at once then turn it

on after 15 to 30 minutes. If colour irregularity should

persist, place the speakers farther away from the set.

The nameplate is located on the bottom exterior of the

unit.

On moving the system

When you carry the system, use the following

procedure to protect the inner mechanism. Remove the

disc, and then press and hold the x button on the

system. After “MECHA LOCK” is displayed on the

front panel display, remove the mains leads from a wall

outlet.

Precautions

IMPORTANT NOTICE

Caution: This system is capable of holding a still

video image or on-screen display image on your

television screen indefinitely. If you leave the still

video image or on-screen display image displayed

on your TV for an extended period of time you risk

permanent damage to your television screen.

Projection televisions are especially susceptible to

this.

GB

4

GB

Welcome!................................................2

Precautions..............................................3

About this Manual...................................6

This System Can Play the Following

Discs .................................................6

Terms for discs........................................6

Notes about Discs ...................................8

Guide to the Control Menu Display........9

Getting Started

Unpacking.............................................11

Inserting Batteries into the Remote.......11

Step 1: Speaker System Hookup...........12

Step 2: Aerial Hookups.........................16

Step 3: TV and Video Component

Hookups..........................................18

Step 4: Connecting the Mains Leads ....20

Speaker Setup........................................21

Playing Discs

Playing Discs ........................................22

Resuming Playback from the Point Where

You Stopped the Disc.....................24

(Resume Play)

Using the DVD’s Menu........................24

Playing VIDEO CDs with PBC Functions

(Ver. 2.0).........................................25

(PBC Playback)

Playing an MP3 Audio Track ...............26

Playing JPEG Image Files ....................27

Creating Your Own Program................30

(Program Play)

Playing in Random Order .....................31

(Shuffle Play)

Playing Repeatedly ...............................32

(Repeat Play)

Searching for a Particular Point on a

Disc.................................................33

(Scan, Slow-motion Play)

Searching for a Title/Chapter/Track/

Index/Album/File............................34

Viewing Disc Information ....................36

Sound Adjustments

Changing the Sound .............................41

Enjoying Surround Sound .................... 43

Using the Sound Effect.........................46

Using Various Additional

Functions

Changing the Angles ............................47

Displaying Subtitles..............................48

Locking Discs.......................................49

(CUSTOM PARENTAL

CONTROL, PARENTAL

CONTROL)

Other Operations

Controlling TV with the Supplied

Remote ...........................................54

Using the Video or Other Unit ............. 55

Enjoying the Radio............................... 56

Using the Radio Data System (RDS) ... 59

Using the Sleep Timer.......................... 59

To change the brightness of the front panel

display............................................60

Returning to the default settings........... 60

Settings and Adjustments

Using the Setup Display....................... 61

Setting the Display or Sound Track

Language........................................62

(LANGUAGE SETUP)

Settings for the Display........................ 63

(SCREEN SETUP)

Custom Settings....................................64

(CUSTOM SETUP)

Settings for the Speakers ......................65

(SPEAKER SETUP)

Table of Contents

5

GB

Additional Information

Troubleshooting....................................69

Specifications........................................72

Glossary ................................................73

Index to Parts and Controls...................76

Language code list ................................81

DVD Setup Menu List..........................82

Index .....................................................83

Quick reference for Remote

Commander ....................................84

6

GB

• The instructions in this manual describe the

controls on the remote. You can also use the

controls on the system if they have the same or

similar names as those on the remote.

• The following symbols are used in this

manual.

* MP3 (MPEG1 Audio Layer 3) is a standard format

defined by ISO/MPEG which compresses audio data.

The “DVD VIDEO” logo is a trademark.

• Title

The longest section of a picture or music

feature on a DVD, movie, etc., in video

software, or the entire album in audio

software.

• Chapter

Section of a picture or a music piece that is

smaller than titles. A title is composed of

several chapters. Depending on the disc, no

chapters may be recorded.

• Album

Section of a music piece or an image on a data

CD containing MP3 audio tracks or JPEG

files.

• Track

Section of a picture or a music piece on a

VIDEO CD, Super Audio CD, CD, or MP3.

• Index (Super Audio CD, CD) / Video

Index (VIDEO CD)

A number that divides a track into sections to

easily locate the point you want on a VIDEO

CD, Super Audio CD, or CD. Depending on

the disc, no indexes may be recorded.

• Scene

On a VIDEO CD with PBC functions

(page 25), the menu screens, moving pictures

and still pictures are divided into sections

called “scenes.”

• File

Section of a picture on a data CD containing

JPEG image files.

About this Manual

Symbol Meaning

Functions available for DVD

VIDEOs and DVD-Rs/DVD-RWs

in video mode or DVD+Rs/

DVD+RWs

Functions available in VIDEO CD

mode

Functions available in CD mode

Functions available in Super Audio

CD and Audio CD mode

Functions available for MP3* audio

tracks

Functions available for JPEG files

This System Can Play the

Following Discs

Format of

discs

Disc logo

DVD VIDEO

Super Audio

CD

VIDEO CD

Audio CD

CD-R/CD-RW

(audio data)

(MP3 files)

(JPEG files)

Terms for discs

Format of

discs

Disc logo

7

GB

Note on PBC (Playback Control)

(VIDEO CDs)

This system conforms to Ver. 1.1 and Ver. 2.0 of

VIDEO CD standards. You can enjoy two kinds

of playback depending on the disc type.

About Multi Session CD

• This system can play Multi Session CDs when

an MP3 audio track is contained in the first

session. Any subsequent MP3 audio tracks

recorded in later sessions can also be played

back.

• This system can play Multi Session CDs when

a JPEG image file is contained in the first

session. Any subsequent JPEG image files

recorded in later sessions can also be played

back.

• If audio tracks and images in music CD format

or video CD format are recorded in the first

session, only the first session will be played

back.

Region code

Your system has a region code printed on the

back of the unit and will only play DVDs

labelled with the same region code.

DVDs labelled will also play on this system.

If you try to play any other DVD, the message

“Playback prohibited by area limitations.” will

appear on the TV screen. Depending on the

DVD, no region code indication may be given

even though playing the DVD is prohibited by

area restrictions.

Examples of discs that the

system cannot play

The system cannot play the following discs:

• CD-ROMs (except for extension “.MP3,”

“.JPG,” or “.JPEG”)

• CD-Rs/CD-RWs other than those recorded in

the following formats:

– music CD format

– video CD format

– MP3/JPEG format that conforms to

ISO9660* Level 1/Level 2, or its extended

format, Joliet

• Data part of CD-Extras

• DVD-ROMs

• DVD Audio discs

• DVD-RAMs

• DVD-RWs in VR (Video Recording) mode

• Progressive JPEG file

* A logical format of files and folders on CD-ROMs,

defined by ISO (International Standard

Organization)

Do not load the following discs:

• A DVD with a different region code (page 7,

74).

• A disc that is neither standard nor circular

(e.g., card, heart, or star shape).

• A disc with paper or stickers on it.

• A disc that has adhesive or cellophane tape still

left on it.

Disc type You can

VIDEO CDs

without PBC

functions

(Ver. 1.1 discs)

Enjoy video playback (moving

pictures) as well as music.

VIDEO CDs

with PBC

functions

(Ver. 2.0 discs)

Play interactive software using

menu screens displayed on the

TV screen (PBC Playback), in

addition to the video playback

functions of Ver. 1.1 discs.

Moreover, you can play high-

resolution still pictures, if they

are included on the disc.

DVD

structure

VIDEO

CD, Super

Audio CD,

or CD

structure

MP3

structure

Disc

Title

Chapter

Track

Index

Album

Track

JPEG

structure

Disc

Album

File

ALL

continued

8

GB

Notes about CD-R/CD-RW/DVD-R/DVD-RW

(Video mode)

In some cases, CD-R/CD-RW/DVD-R/DVD-RW

(Video mode) cannot be played on this player due to

the recording quality or physical condition of the disc,

or the characteristics of the recording device and

authoring software.

The disc will not play if it has not been correctly

finalized. For more information, see the operating

instructions for the recording device.

Note that discs created in the Packet Write format

cannot be played.

Music discs encoded with copyright

protection technologies

This product is designed to play back discs that

conform to the Compact Disc (CD) standard.

Recently, various music discs encoded with copyright

protection technologies are marketed by some record

companies. Please be aware that among those discs,

there are some that do not conform to the CD standard

and may not be playable by this product.

Note on playback operations

of DVDs and VIDEO CDs

Some playback operations of DVDs and VIDEO

CDs may be intentionally set by software

producers. Since this system plays DVDs and

VIDEO CDs according to the disc contents the

software producers designed, some playback

features may not be available. Also, refer to the

instructions supplied with the DVDs or VIDEO

CDs.

Copyrights

This product incorporates copyright protection

technology that is protected by U.S. patents and

other intellectual property rights. Use of this

copyright protection technology must be

authorized by Macrovision, and is intended for

home and other limited viewing uses only unless

otherwise authorized by Macrovision. Reverse

engineering or disassembly is prohibited.

This system incorporates with Dolby* Digital

and Dolby Pro Logic (II) adaptive matrix

surround decoder and the DTS** Digital

Surround System.

* Manufactured under license from Dolby

Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are

trademarks of Dolby Laboratories.

**Manufactured under license from Digital Theater

Systems, Inc.

“DTS” and “DTS Digital Surround” are trademarks

of Digital Theater Systems, Inc.

On handling discs

• To keep the disc clean, handle the disc by its

edge. Do not touch the surface.

• Do not stick paper or tape on the disc.

• Do not expose the disc to direct sunlight or

heat sources such as hot air ducts, or leave it in

a car parked in direct sunlight as the

temperature may rise considerably inside the

car.

• After playing, store the disc in its case.

On cleaning

• Before playing, clean the disc with a cleaning

cloth.

Wipe the disc from the centre out.

• Do not use solvents such as benzine, thinner,

commercially available cleaners, or anti-static

spray intended for vinyl LPs.

This system can only play back a standard

circular disc. Using neither standard nor circular

discs (e.g., card, heart, or star shape) may cause

a malfunction.

Do not use a disc that has a commercially

available accessory attached, such as a label or

ring.

Notes about Discs

9

GB

Use the Control Menu to select a function that you would like to use. The Control Menu display appears

when the DVD DISPLAY button is pressed. For details, refer to the page in parentheses.

List of Control Menu Items

Guide to the Control Menu Display

DISC Displays the disc name or the disc type inserted into the system.

TITLE (DVD only) (page 34)/

SCENE (only VIDEO CD in PBC playback) /

TRACK (VIDEO CD only) (page 34)

Selects the title (DVD), or the track (VIDEO CD) to be

played.

Displays the scene (VIDEO CD in PBC playback).

CHAPTER (DVD only) (page 35)/

INDEX (VIDEO CD only) (page 35)

Selects the chapter (DVD) or the index (VIDEO CD) to be

played.

ALBUM (MP3 only) (page 26, 34) Selects the album (MP3) to be played.

TRACK (Super Audio CD/CD/

MP3 only) (page 26, 34)

Selects the track (Super Audio CD/CD/MP3) to be played.

INDEX (Super Audio CD/CD only)

(page 35)

Displays the index and selects the index (Super Audio CD) to

be played.

TIME (page 36) Checks the elapsed time and the remaining playback time.

Inputs the time code for picture and music searching.

AUDIO (DVD/VIDEO CD/Super

Audio CD/CD/MP3 only) (page 41)

Changes the audio setting.

SUBTITLE (DVD only) (page 48) Displays the subtitles.

Changes the subtitle language.

ALBUM (JPEG only) (page 28) Selects the album (JPEG) to be played.

2: FRENCH

3: SPANISH

1: ENGLISH

Select:

SUBTITLE

DVD

1 2

(

2 7

)

MAKING SCENE

1 8

(

3 4

)

T

1 : 3 2 : 5 5

ENTER

Currently playing title number (Video CD/

Super Audio CD/CD: track number)

Playing time

Currently playing chapter

number (Video CD/Super

Audio CD/CD: index number)

Icon of selected

Control Menu item

Control Menu items

Function name of selected

Control Menu item

Operation message

Disc name or

disc type

Total number of

titles or tracks

recorded

Currently playing

title name

Total number of chapters or indexes recorded

Playback status

(NPlayback, XPause, xStop, etc.)

Type of disc being

played back

Current setting

Options

continued

10

GB

Tips

• Each time you press DVD DISPLAY, the Control Menu display changes as follows:

The Control Menu items vary, depending on the disc.

• The Control Menu icon indicator lights up in green t unless you set the REPEAT setting to

“OFF.”

• The “ANGLE” indicator lights up in green only when multiple angles are recorded on the disc.

FILE (JPEG only) (page 28) Selects the file (JPEG) to be played

DATE (JPEG only) (page 40) Displays the date information.

ANGLE (DVD only) (page 47) Changes the angle.

PLAYMODE (VIDEO CD/Super

Audio CD/CD/MP3/JPEG only) (page 32)

Selects the play mode.

REPEAT (page 32) Plays the entire disc (all titles/all tracks), one title/chapter/

track/album, or contents of program repeatedly.

CUSTOM PARENTAL

CONTROL (page 49)

Sets the disc to prohibit playing.

Control Menu display

Control Menu display off

m

Getting Started

11

GB

Check that you have the following items:

•Speakers (5)

• Subwoofer (1)

• AM loop aerial (1)

• FM wire aerial (1)

• Speaker cords (3.5m × 3, 10m × 2, 5m × 1)

• Remote Commander (remote) RM-SP800 (1)

• R6 (size AA) batteries (2)

• Operating Instructions (1)

• Speakers-connection and Installation (card)

(1)

• Tall type speakers-connection (card) (1)

You can control the system using the supplied

remote. Insert two R6 (size AA) batteries by

matching the 3 and # ends on the batteries to

the markings inside the compartment. When

using the remote, point it at the remote sensor

on the system.

Notes

• Do not leave the remote in an extremely hot or humid

place.

• Do not use a new battery with an old one.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not expose the remote sensor to direct light from

the sun or lighting apparatus. Doing so may cause a

malfunction.

• If you do not use the remote for an extended period of

time, remove the batteries to avoid possible damage

from battery leakage and corrosion.

Getting Started

Unpacking

Inserting Batteries into

the Remote

12

GB

Connect the supplied speaker system using the supplied speaker cords by matching the colours of the

jacks to those of the cords. Do not connect any speakers other than those supplied with this system.

To obtain the best possible surround sound, specify the speaker parameters (distance, level, etc.) on

page 21.

Required cords

Speaker cords

The connector and the colour tube of the speaker cords are the same colour as the label of the jacks to

be connected.

Step 1: Speaker System Hookup

(–)

(+)

colour tube

(+)

(–)

Getting Started

13

GB

Terminals for connecting the speakers

Note on placing speakers

Use caution when placing the subwoofer or a speaker stand (not supplied) that is attached with the

front/surround speakers on a specially treated (waxed, oiled, polished, etc.) floor, as staining or

discoloration may result.

Connect the To the

Front speakers SPEAKER FRONT L (white) and R (red) jacks

Surround speakers SPEAKER SURR L (blue) and R (grey) jacks

Centre speaker SPEAKER CENTER (green) jack

Subwoofer SPEAKER WOOFER (purple) jack

SPEAKER

CENTER FRONT LFRONT R

WOOFER SURR LSURR R

Front speaker (R)

Centre speaker

Front speaker (L)

Surround speaker (R)

Subwoofer

Surround speaker (L)

continued

14

GB

Note

Do not catch the speaker cable insulation in the SPEAKER jack.

Tip

Connect the speaker cable after bending the speaker wire at the end of the insulation. This prevents the speaker cable

from being caught in the SPEAKER jack.

To avoid short-circuiting the speakers

Short-circuiting of the speakers may damage the system. To prevent this, be sure to follow these

precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch

another speaker jack or the bare wire of another speaker cord.

Examples of poor conditions of the speaker cord

After connecting all the components, speakers, and mains lead, output a test tone to check that all the

speakers are connected correctly. For details on outputting a test tone, see page 67.

If no sound is heard from a speaker while outputting a test tone, or a test tone is output from a speaker

other than the one currently displayed in the front panel display, the speaker may be short-circuited. If

this happens, check the speaker connection again.

Note

Be sure to match the speaker cord to the appropriate terminal on the components: 3 to 3, and # to #. If the cords

are reversed, the sound will lack bass and may be distorted.

Stripped speaker cord is

touching another speaker

terminal.

Stripped cords are touching

each other due to excessive

removal of insulation.

Getting Started

15

GB

To change the speaker cables

If you want to use a different speaker cable, you can detach the plug for attachment to another cable.

Detaching

With the catcher facing down, press and hold the plug down against a flat surface and remove the cords

from plug.

Attaching

While pressing the plug down against a flat surface, insert the new speaker cords.

Note that the cord marked with a line should be attached to the minus (-) side of the plug.

Note

Be careful not to damage the surface you use (desk, etc.) when attaching/detaching the speaker cords.

Tips

• You can use any commercially sold speaker cable of gauge cord AWG #18 - AWG #24.

• Before attaching a new cable, strip off 10 mm ( 13/32 in.) of its insulation and twist the bare wires of both cords.

Catcher

10 mm

16

GB

Connect the supplied AM/FM aerials for listening to the radio.

Terminals for connecting the aerials

Notes

• To prevent noise pickup, keep the AM loop aerial away from the system and other components.

• Be sure to fully extend the FM wire aerial.

• After connecting the FM wire aerial, keep it as horizontal as possible.

Tip

When you connect the supplied AM loop aerial, the cord (A) and the cord (B) can be connected in either terminal.

Step 2: Aerial Hookups

Connect the To the

AM loop aerial AM terminals

FM wire aerial FM 75Ω COAXIAL jack

COAXIAL

FM 75

OPTICAL

DIGITAL

IN

AM

CENTER FRONT LFRONT R

WOOFER SURR LSURR R

SPEAKER

VIDEO OUTAUDIO OUT

VIDEO INAUDIO IN

RL

VIDEO 1

VIDEO 2

VIDEO INAUDIO IN

RL

VIDEO 2

OUTPUT(TO TV)

EURO AV

AM loop aerial

FM wire aerial

AM

A

B

Getting Started

17

GB

Tip

If you have poor FM reception, use a 75-ohms coaxial cable (not supplied) to connect the system to an outdoor

FM aerial as shown below.

COAXIAL

FM 75

AM

Outdoor FM

aerial

System

18

GB

Required cords

SCART (EURO AV) cord for connecting a TV (not supplied)

Audio/video cords (not supplied)

When connecting a cord, be sure to match the colour-coded sleeves to the appropriate jacks on the

components.

Terminals for connecting video components

Connecting the system to a TV

Connect the system to your TV using the SCART (EURO AV) cord. Be sure to connect the SCART

(EURO AV) cord to the T EURO AV OUTPUT (TO TV) jack on the system.

When you connect using the SCART (EURO AV) cord, check that the TV conforms to S video or RGB

signals. If the TV conforms to S video, change the input mode of the TV to RGB signals. Refer to the

operating instructions supplied with the TV to be connected.

Note

When you use the VIDEO 1 line outputs, please set the system to 2CH STEREO mode. If the system is not in 2CH

STEREO mode, the line outputs may not function properly.

Step 3: TV and Video Component Hookups

Connect the To the

TV T EURO AV OUTPUT (TO TV) jack

VCR VIDEO 1 jacks

Digital satellite receiver VIDEO 2 jacks

Yellow (Video)

White (L/audio)

Red (R/audio)

Getting Started

19

GB

Notes

• Make connections securely to prevent unwanted noise.

• Refer to the instructions supplied with the TV.

• The system cannot output component video signals.

• The system cannot output the audio signal of the connected TV. When you listen to the audio signal of the TV by

using the connected speakers, input the audio signal of the TV from the AUDIO IN L/R jack.

When connecting to a standard 4:3 screen TV

Depending on the disc, the image may not fit your TV screen.

If you want to change the aspect ratio, please refer to page 63.

Connecting a VCR to the system

Connect the VCR to the VIDEO IN and AUDIO IN L/R jacks of the system. Be sure to make the

connections securely to avoid hum and noise. If using VIDEO1 distorts the sound, reconnect the VCR

to VIDEO2.

To listen to the TV or game machine (ex: PlayStation 2) sound

by using the system

Connect the audio output jacks of the TV or game machine to the VIDEO 2 AUDIO IN jacks of the

system with the audio cords (optional).

VIDEO

OUT

R

VIDEO

IN

AUDIO

OUT

AUDIO

IN

L

VIDEO

OUT

R

AUDIO

OUT

L

OPTICAL

DIGITAL

OUT

INTPUT(FROM VIDEO)

EURO AV

COAXIAL

FM 75

OPTICAL

DIGITAL

IN

AM

CENTER FRONT LFRONT R

WOOFER SURR LSURR R

SPEAKER

VIDEO OUTAUDIO OUT

VIDEO INAUDIO IN

RL

VIDEO 1

VIDEO 2

VIDEO INAUDIO IN

RL

VIDEO 2

OUTPUT(TO TV)

EURO AV

IN OUT INOUT OUT

TV

VCR

Digital satellite receiver or

PlayStation 2 etc.

continued

20

GB

Notes

• Do not connect the system to a VCR. If you pass video signals from the system via a VCR, you may not receive a

clear image on the TV screen.

• If you cannot view the picture from a VCR through this system which is connected to a TV with RGB component

jacks, set to t (Audio/Video) on your TV. If you select (RGB), the TV cannot receive the signal from

the VCR.

• If you want to use your VCR’s SmartLink function, connect the VCR to your TV’s SmartLink jack.

• The SmartLink function may not work properly if your VCR is connected to your TV via this system.

• The system does not output S video signals.

• When you select “DVD” by pressing FUNCTION (page 55), the video signal and RGB signal are not output from

the VIDEO IN jacks. Also, the system cannot output the component video signal.

• When you select VIDEO 1 or VIDEO 2 by pressing FUNCTION (page 55), the audio signal from the AUDIO L/

R jack is output to the connected speakers. The audio signal is not output from the T EURO AV OUTPUT (TO

TV) jack.

Before connecting the mains leads of this system to a wall outlet, connect the speakers to the system

(see page 13).

Step 4: Connecting the Mains Leads

Страница загружается...

Sony DAV-SC6 Инструкция по эксплуатации

Похожие модели бренда

Модели других брендов