Acson 5SL Инструкция по установке

CEILING/FLOOR

EXPOSED CONVERTIBLE

SPLIT TYPE AIR CONDITIONERS

CEILING EXPOSED

INSTALLATION MANUAL

IM-CEE-1004-ACSON

Part No.: R08019025472

1-1

English

OUTLINE AND DIMENSIONS

Indoor Unit (5CEE / CEE Series)

All dimensions are in mm

Outdoor Unit (5SL / SL15C / CR)

928

65

400

230

630

218

1080

All dimensions are in mm/(in)

LKL

N

C

M

(1.2)

30

A

D

O

(0.1)

3

B

(2.6)

65

(3.1)

80

N

F

E

C

G

H

JI

(0.7)

19

Dimension A B C D E F G H I J K L M N O

5SL / SL15C /CR 700 521 250 485 175 36 95 93 86 68 441 130 111 15 18

(27.5) (20.5) (9.8) (19.1) (6.8) (1.4) (3.7) (3.6) (3.3) (2.6) (17.3) (5.1) (4.3) (0.5) (0.7)

1-2

Dimension A B C D E F G H J K L M N P Q R

5SL / SL20C / CR

855

648

328 303 309

630

49 116 75 187 98 392 362 126 603 164

5SL / SL25C / CR

(33.7)

(25.5)

(12.9) (11.9) (12.2)

(24.8)

(1.9) (4.6) (3.0) (7.4) (3.9) (15.4) (14.3) (5.0) (23.7) (6.5)

5SL / SL28C / CR

750 730

(29.5) (28.7)

Outdoor Unit (5SL / SL30C)

All dimensions are in mm/(in)

745.5

25.0

141.0 141.0

20.0448.0

20.0

1030.0

852.0

45.8

62.3

400.0

40.0 40.0320.0

All dimensions are in mm/(in)

A

QP

P

M

N

15.0

39.0

R

A

D

C 5.0

E20.0

F

20.0

B

2.5

20.0

K

G

141.0

C5.0

160.0 H

L

64

.

5

J

Outdoor Unit (5SL / SL Series)

1-3

English

! CAUTION

Please take note of the following important points when

installing.

• Do not install the unit where leakage of flammable

gas may occur.

If gas leaks and accumulates around the unit, it

may cause fire ignition.

• Ensure that drainage piping is connected properly.

If the drainage piping is not connected properly, it

may cause water leakage which will dampen the

furniture.

• Do not overcharge the unit.

This unit is factory pre-charged.

Overcharge will cause over-current or damage to

the compressor.

• Ensure that the unit’s panel is closed after service or

installation.

Unsecured panels will cause the unit to operate

noisily.

• Sharp edges and coil surfaces are potential locations

which may cause injury hazards.

Avoid from being in contact with these places.

• Before turning off the power supply, set the remote

controller’s ON/OFF switch to the “OFF” position

to prevent the nuisance tripping of the unit. If this is

not done, the unit’s fans will start turning automatically

when power resumes, posing a hazard to service

personnel or the user.

• Do not operate any heating apparatus too close to

the air conditioner unit. This may cause the plastic

panel to melt or deform as a result of the excessive heat.

• Ensure the color of wires of the outdoor unit and the

terminal markings are same to the indoors

respectively.

• IMPORTANT : DO NOT INSTALL OR USE THE

AIR CONDITIONER UNIT IN A LAUNDRY ROOM.

! WARNING

• Installation and maintenance should be performed by

qualified persons who are familiar with local code and

regulation, and experienced with this type of appliance.

• All field wiring must be installed in accordance with the

national wiring regulation.

• Ensure that the rated voltage of the unit corresponds to

that of the name plate before commencing wiring work

according to the wiring diagram.

• The unit must be GROUNDED to prevent possible hazard

due to insulation failure.

• All electrical wiring must not touch the refrigerant

piping, or any moving parts of the fan motors.

• Confirm that the unit has been switched OFF before

installing or servicing the unit.

• Disconnect from the main power supply before servicing

the air conditioner unit.

• DO NOT pull out the power cord when the power is ON.

This may cause serious electrical shocks which may result

in fire hazards.

• Keep the indoor and outdoor units, power cable and

transmission wiring, at least 1m from TVs and radios, to

prevent distorted pictures and static. {Depending on the

type and source of the electrical waves, static may be heard

even when more than 1m away}.

SAFETY PRECAUTIONS

Disposal requirements

Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall

not be mixed with unsorted household waste.

Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the refrigerant,

of oil and of other parts must be done by a qualified installer in accordance with relevant local and national legislation.

Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By ensuring

this product is disposed of correctly, you will help to prevent potential negative consequences for the environment

and human health. Please contact the installer or local authority for more information.

Batteries must be removed from the remote controller and disposed of separately in accordance with relevant local

and national legislation.

NOTICE

This manual provides the procedures of installation to ensure a safe and good standard of operation for the air

conditioner unit.

Special adjustment may be necessary to suit local requirements.

Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.

INSTALLATION MANUAL

1-4

Important information regarding the refrigerant used

This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. Do not vent gases into the atmosphere.

Refrigerant type: R410A R407C

GWP

(1)

value: 1975 1652.5

(1)

GWP = global warming potential

Please fill in with indelible ink,

 1 the factory refrigerant charge of the product,

 2 the additional refrigerant amount charged in the field and

 1 + 2 the total refrigerant charge

on the refrigerant charge label supplied with the product.

The filled out label must be adhered in the proximity of the product charging port (e.g. onto the inside of the service cover).

1 factory refrigerant charge of the product:

see unit name plate

(2)

2 additional refrigerant amount charged in the field

3 total refrigerant charge

4 Contains fluorinated greenhouse gases covered by the Kyoto Protocol

5 outdoor unit

6 refrigerant cylinder and manifold for charging

(

(2)

In case of multiple indoor systems, only 1 label must be adhered*, mentioning the total factory refrigerant charge of all

indoor units connected in the refrigerant system.

Periodical inspections for refrigerant leaks may be required depending on European or local legislation. Please contact your

local dealer for more information.

* on the outdoor unit

OR

IMPORTANT

1-5

English

Figure A

Preliminary Site Survey

• Electrical supply and installation shall conform to the

local authority (e.g. National Electrical Board).

• Voltage supply fluctuation must not exceed ±10% of the

rated voltage. Electricity supply lines must be

independent of welding transformers which can cause

high supply fluctuation.

• Ensure that the installation location is convenient for

wiring and piping.

Standard Mounting

Ensure that the overhead supports are strong enough to hold

the weight of the unit. Position the hanger rods (wall

mounting bracket for floor standing), and check for its

alignment with the unit as shown in Figure A. Also, check

that the hangers are secured and the base of the fan coil unit

is leveled in both horizontal directions, taking into account

the gradient for drainage flow as recommended in Figure B.

INSTALLATION OF THE INDOOR UNIT

1073.0

535.5268.0

485.0 145.0

336.0 134.5

630.0

Figure B

10.0mm

Please ensure that the following steps are taken:

• Check the gradient for drainage flow as recommended in Figure B.

• Provide clearance for easy servicing and optimal air flow as shown in Figure C.

• The indoor unit must be installed such that there is no short circuit of the cool discharge air with the warm

return air.

• Do not install the indoor unit where there is direct sunlight shining on the unit. The location should be

suitable for piping and drainage installation. The unit must be a large distance away from the door.

Figure C

Utensils, Furnitures Or Built-

In Architectural Features Must

Not Protrude More Than

250.0mm

Min

300.0mm

Min

500.0mm

Min 250.0mm

Min 400.0mm

Min 250.0mm

Min 1.0m

Ceiling Type

Floor Standing Type

1-6

UNDER CEILING INSTALLATION

Install the Suspension Bolts

1. Install the suspension bolts so that it can support the indoor unit.

2. Adjust distance to ceiling before installation.

3. Refer to the dimension given to install the unit.

Install the Indoor Units

1. Insert the suspension bolts into the fittings of the hanger bracket.

2. Set the nuts and washer on the both side of the metal fittings.

3. Secure it with nuts.

4. Attach the hanger cover (4 pcs) to the units.

Suspension Bolt

Hanger Cover

Suspension Bolt

Hanger Rod

28.0

Floor Standing Installation

479.0 Min 547.0

Mounting Bracket

509.0

458.0

Min 301.0

Min 759.0

Rear Piping Hole

Floor

123.0

78.0

40.0

307.4

1-7

English

1. Refer to the dimension as illustrated when installing the mounting bracket.

2. When the rear piping, determine the pipe hose position. Drill the pipe hole at the slight downward slant to the outdoor side.

Mounting Bracket

Wall

Piping and Drain Hose Installation ( Under Ceiling Type)

1. The piping direction can be 2 ways as illustrated.

2. The drain hose is only 1 way.

Rear Piping and Drain Hose Rear Piping Hose

Upper Piping

OR

Hook the unit on the

mounting bracket

Piping and Drain Hose Installation (Floor Standing Type)

Wall

OR

Piping and Drain Hose

Wall

Piping and Drain Hose

How to Install the Drain Hose

1. Remove the two screws and the drain pipe holder.

2. Cut a slit for the drain hose hole.

3. Place the drain hose on the v-shape area and secure it

with drain pipe holder and two screws.

Slit for Drain Hose Hole

Screws

Drain Pipe Holder

1-8

How to Remove Air Inlet Grille

1. Remove the air inlet grille by both hands as the direction

shown.

2. Loosen the screw for fixing the panel arm (3 screw, left,

right and center). Do not remove the screw at this time.

Air Inlet Grille

Axis of the

Front Panel

Rib

Grille Holder (Center)

(Optional)

Screw

Air Inlet

Grille Holder

Grille Holder (Center)

Grille Holder (L/R)

3. Move the air inlet grille upward, and then turn it

backwards. (Do not use too much force).

4. Remove the grille holder (both left and right side). After

that, remove to air intake grille.

5. Remove the grille holder (center) from the panel.

How to Install the Air Filter

(A)

(B) (B)

Snap in the filter in order to secure it

Install the filter to the panel in the (A)

direction follow by (B) to secure the filter.

To Adjust the Vane Direction

Adjust the vane linkage as the direction shown to get the

required vane direction

Dimension of the fresh air intake hole

70.0

Ø 3.0

70.0

Ø 64.0

1-9

English

INSTALLATION OF FRESH AIR INTAKE

1. Knock out the fresh air intake hole at the top panel

2. Assemble the axial fan, fresh air adapter, filter and dust hose as shown in figure below.

3. Connect the wire to the control box as indicated in the wiring diagram below:

INSTALLATION OF THE OUTDOOR UNIT

The outdoor unit must be installed in such a way, so as to

prevent short circuit of the hot discharged air or obstruction

to the smooth air flow. Please follow the installation

clearance shown in the figure. Select the coolest possible

place where intake air temperature is not greater than the

outside air temperature (maximum 45°C).

Installation Clearance

Return Air

Discharge Air

NOTE : If there is any obstacle higher than 2m, or if there

is any obstruction at the upper part of the unit,

please allow more space than the figure indicated

in the above table.

Dimension A B C D

Minimum Distance

300 1000 300 500

(mm)

Service Access

Return Air

WIRED OR

WIRELESS

REMOTE

CONTROLLER

LCD/WIRELESS

SLM

DC SWG

TWIN

ROOM

ID

OD

TRANSFORMER

DC.ION

HIGH MED

LOW

WTP

LIVE

COMP.

L

N2 N1

INDOOR COIL SENSOR

RETURN AIR SENSOR

AS

2" DUCT HOSE

ASSY. FRESH AIR ADAPTER

FILTER FRESH AIR INTAKE

TOP PANEL

FA

FA : FRESH AIR

4. The axial fan model are as follow.

a. ebm axial fan. 8556A - pin type.

b. ebm axial fan. 8556N - wire type.

Obstacle

1-10

REFRIGERANT PIPING

5CE/ 5CE/ 5CE/ 5CE/

Model CE15E CE20E CE25E CE28E

/ER /ER /ER /ER

Maximum Length m 15 15 15 15

Maximum Elevation m 888 8

Maximum Number of Bends

10 10 10 10

Therefore, always select the shortest path for the piping system

and follow the recommendations as tabulated in the table.

Maximum Pipe Length And Maximum Number Of

Bends

If the pipe length is too long, both the capacity and the

reliability of the unit will decrease. As the number of bends

increases, resistance of the piping system to the refrigerant flow

increases and thus lowering the capacity, as a result the

compressor may become defective. See Figure O and

Figure P.

Indoor Unit

Figure O

Figure P

Piping Length

Indoor Unit

Max. Elevation Height

Elevation

Outdoor Unit

Maximum

Piping 20m

20.0 m

Outdoor Unit

Remove Burr

Copper Tube

Swaging Block

Ø Tube, D A (mm)

Inch mm Imperial Rigid

1/4" 6.35 1.3 0.7

3/8" 9.52 1.6 1.0

1/2" 12.70 1.9 1.3

5/8" 15.88 2.2 1.7

3/4" 19.05 2.5 2.0

Cutting Copper Tube

Piping Connection To The Units

• Align the center of the piping and tighten the flare nut

sufficiently with fingers.

• Finally, tighten the flare nut with the torque wrench

until the wrench clicks.

Pipe Size (mm/in) Torque (Nm)

6.35 (1/4) 18

9.53 (3/8) 42

12.7 (1/2) 55

15.88 (5/8) 65

19.05 (3/4) 78

• If any brazing work is required, ensure that the nitrogen gas

is passed through coil and joints while the brazing work is

being done. This will eliminate soot formation on the inside

walls of the copper tubings.

• Cut the connection pipe with a pipe cutter.

• Remove burrs from cut edges of the pipes with remover.

Hold the end of the pipe downwards to prevent metal chips

from entering the pipe.

• Insert the flare nuts, mounted on the connection parts of both

the indoor unit and outdoor unit onto the copper pipes.

• Flare the pipe with extra length above the flaring tool as

shown in the table.

• The flared edge must be even and not cracked or scratched.

1/4t

Piping Works

• Do not use contaminated or damaged copper tubing. Do not remove plastic, rubber plugs and brass nuts from the valves,

fittings, tubings and coils until you are ready to connect suction or liquid line into valves or fittings.

Spanar

Torque Wrench

Indoor Piping

Flare Nut

Flared TubeFlare Joint

1-11

English

ELECTRICAL WIRING CONNECTION

Electrical Wiring Connection For 5CE / CE 15/20/25/28E Vs 5SL /SL 15/20/25/28/30C

Model

Indoor 5CE/CE15/20ER 5CE/CE25ER 5CE/CE28ER

Outdoor 5SL/SL15/20CR 5SL/SL25CR 5SL/SL28/30CR

Voltage Range**

220V – 240V /1Ph /50Hz +

!

or 208V – 230V /1Ph /60Hz +

!

Power Supply Cable Size mm

2

2.5 2.5 4.0

Number Of Conductors* 333

Interconnection Cable Size mm

2

2.5 2.5 1.5

Number Of Conductors* 557

Recommended Fuse* A 16 20 25

Electrical Wiring Connection For 5CE / CE15/20/25/28ER Vs 5SL / SL15/20/25/28/30CR

The electrical power supply must be provided

with protection devices (circuit breaker or

fuse) with all pole separation system,

minimum contact gap of 3mm.

Terminal Strip

Indoor Unit

Interconnection Cable

Terminal Strip

Outdoor Unit

Model

Indoor 5CE/CE15/20E 5CE/CE25E 5CE/CE28E

Outdoor 5SL/SL15/20C 5SL/SL25C 5SL/SL28/30C

Voltage Range** 220V – 240V /1Ph /50Hz +

!

or 208V – 230V /1Ph /60Hz +

!

Power Supply Cable Size mm

2

2.5 2.5 4.0

Number Of Conductors* 33 3

Interconnection Cable Size mm

2

2.5 2.5 2.5

Number Of Conductors* 33 3

Recommended Fuse* A 16 20 25

5CE/CE15E Vs 5SL/SL15C

5CE/CE20E Vs 5SL/SL20C

5CE/CE25E Vs 5SL/SL25C

5CE/CE28E Vs 5SL/SL28C

The electrical power supply must be provided

with protection devices (circuit breaker or

fuse) with all pole separation system,

minimum contact gap of 3mm.

5CE/CE28E Vs 5SL/SL30C

Power Supply Cable

!

Terminal Strip

Indoor Unit

Interconnection Cable

Terminal Strip

Outdoor Unit

Power Supply Cable

COMP

L/L1

N/L2

COMP

N

COMP

L/L1

N/L2

COMP

L

N

L

N

1-12

Terminal Strip

Indoor Unit

Interconnection Cable

Terminal Strip

Outdoor Unit

5CE/CE15ER Vs

5SL/SL15CR

5CE/CE20ER Vs

5SL/SL20CR

5CE/CE25ER Vs

5SL/SL25CR

Power Supply Cable

Outdoor Coil Sensor

The electrical power supply must be

provided with protection devices (circuit

breaker or fuse) with all pole separation

system, minimum contact gap of 3mm.

!

Terminal Strip

Indoor Unit

Interconnection Cable

Terminal Strip

Outdoor Unit

5CE/CE28ER Vs

5SL/SL28CR

Power Supply Cable

Outdoor Coil Sensor

Terminal Strip

Indoor Unit

Interconnection Cable

Terminal Strip

Outdoor Unit

5CE/CE28CR Vs

5SL/SL30CR

Power Supply Cable

Outdoor Coil Sensor

The electrical power supply must

be provided with protection

devices (circuit breaker or fuse)

with all pole separation system,

minimum contact gap of 3mm.

!

4WV

OF

COMP

L/L1

4WV

OF

COMP

N

N/L2

COMP

L/L1

N/L2

A

4WV

OF

E

A

4WV

OF

COMP

L

N

L

N

COMP

L/L1

N/L2

A

4WV

OF

E

4WV

OF

COMP

N

The electrical power supply must be

provided with protection devices

(circuit breaker or fuse) with all pole

separation system, minimum contact

gap of 3mm.

!

1-13

English

VACUUMING AND CHARGING

Purging The Piping And The Indoor Unit

Except for the outdoor unit which is pre-charged with

refrigerant, the indoor unit and the refrigerant

connection pipes must be air-purged because the

aircontaining moisture that remains in the refrigerant cycle

may cause malfunction of the compressor.

• Remove the caps from the valve and the service port.

• Connect the center of the charging gauge to the vacuum

pump.

• Connect the charging gauge to the service port of the

3-way valve.

• Start the vacuum pump. Evacuate for approximately 30

minutes. The evacuation time varies with different

vacuum pump capacity. Confirm that the charging gauge

needle has moved towards -76mmHg (0~76mmHg).

Caution

• If the gauge needle does not move to 0~76mmHg,

be sure to check for gas leaks (using the refrigerant

detector) at flare type connection of the indoor and

outdoor unit and repair the leak before proceeding

to the next step.

• Close the valve of the changing gauge and stop the

vacuum pump.

• On the outdoor unit, open the suction valve (3 way) and

liquid valve (2 way) (in anti-clockwise direction) with

4mm key for hexagon sacked screw.

Additional Charge

The refrigerant is pre-charged in the outdoor unit. If the piping

length is less than 7.6m, then additional charge after

vacuuming is not necessary. If the piping length is more than

7.6m, then use the additional charge valve as indicated in the

table below.

Cooling Only (R410A)

Heat Pump (R22)

Heat Pump (R410A)

Indoor CE15/20E CE25E CE28E

Outdoor SL15/20C SL25C SL28 C SL30C

Additional

16 39 39

Charge [g/m]

Indoor 5CE15E 5CE20E 5CE25E 5CE28E

Outdoor 5SL15C 5SL20C 5SL25C 5SL28C 5SL30C

Additional

91010 24

Charge [g/m]

Indoor CE15ER CE20ER CE25ER CE28ER

Outdoor SL15CR SL20CR SL25CR SL28CR SL30CR

Additional

24 22 22 56

Charge

[g/m]

Indoor 5CE15/20ER 5CE25ER 5CE28ER

Outdoor 5SL15/20CR 5SL25CR 5SL28CR 5SL30CR

Additional

16 10 38

Charge

[g/m]

Cooling Only (R22)

Liquid Side

Indoor Unit

Outdoor Unit

Gas Side

Low

Hi

Vacuum

Pump

Open

Close

Discharge Valve

Suction Valve

Service Port

Outdoor Unit

3 Ways Valve

Flare Nut

Refrigerant Piping

Allen Key

E.g. CE20E & SL20C with 15m piping length, additional piping

length is 7.4m. Thus,

Additional Charge = 7.4[m] x 16[g/m]

= 118.4[g]

1-14

STANDARD OPERATING CONDITIONS

SERVICE AND MAINTENANCE

Service Parts

Indoor Air Filter

Indoor Unit

Maintenance Procedures

1. Remove any dust adhering to the filter by using a vacuum cleaner or

wash in lukewarm water (below 40°C) with a neutral cleaning detergent.

2. Rinse the filter well and dry before placing it back onto the unit.

3. Do not use gasoline, volatile substances or chemicals to clean the filter.

1. Clean any dirt or dust on the grille or panel by wiping it with a soft

cloth soaked in lukewarm water (below 40°C) and a neutral detergent

solution.

2. Do not use gasoline, volatile substances or chemicals to clean the

indoor unit.

Period

At least once

every 2 weeks.

More frequently if

necessary.

At least once

every 2 weeks.

More frequently if

necessary.

Charge Operation

This operation must be done by using a gas cylinder and a

precise weighing machine. The additional charge is

topped-up into the outdoor unit using the suction valve via

the service port.

• Remove the service port cap.

• Connect the low pressure side of the charging gauge to

the suction service port center of the cylinder tank and

close the high pressure side of the gauge. Purge the air

from the service hose.

• Start the air conditioner unit.

• Open the gas cylinder and low pressure charging valve.

• When the required refrigerant quantity is pumped into

the unit, close the low pressure side and the gas cylinder

valve.

• Disconnect the service hose from service port. Put back

the service port cap.

Suction Valve

Discharge Valve

Liquid Side

Indoor Unit

Outdoor Unit

Gas Side

Low

Hi

Open

Close

Open

Check

Valve

Heat Pump Unit

Cooling unit

Temperature Ts °C / °F Th °C / °F

Minimum indoor

19.4 / 66.9 13.9 / 57.0

temperature

Maximum indoor

26.7 / 80.1 19.4 / 66.9

temperature

Minimum outdoor

19.4 / 66.9 13.9 / 57.0

temperature

Maximum outdoor

46 / 114.8 24 / 75.2

temperature

Temperature Ts °C / °F Th °C / °F

Minimum indoor

10 / 50 -

temperature

Maximum indoor

26.7 / 80.1 -

temperature

Minimum outdoor

-8 / 17.6 -9 / 15.8

temperature

Maximum outdoor

24 / 75.2 18 / 64.4

temperature

Ts: Dry bulb temperature.

Th: Wet bulb temperature.

1-15

English

If any malfunction of the air conditioner unit is noted, immediately switch off the power supply to the unit.

Check the following fault conditions and causes for some simple trouble shooting tips.

TROUBLESHOOTING

Causes / Action

- Protection against frequent starting. Wait for 3 to 4 minutes for

the compressor to start operating.

- Power failure, or the fuse needs to be replaced.

- The power plug is disconnected.

- It is possible that your delay timer has been set incorrectly.

- If the fault persist after all these verifications, please

contact the air conditioner unit installer.

- The air filter is dirty.

- The doors or windows are open.

- The air suction and discharge are clogged.

- The regulated temperature is not high enough.

- Odors may be caused by cigarettes, smoke particles, perfume

etc. which might have adhered onto the coil.

- This is caused by air humidity after an extended long period of

operation.

- The set temperature is too low, increase the temperature setting

and operate the unit at high fan speed.

- Switch off unit and call dealer.

- Refrigerant fluid flowing into the evaporator coil.

Fault

1. The compressor does not operate 3 minutes after the air

conditioner unit is started.

2. The air conditioner unit does not operate.

3. The air flow is too low.

4. Discharge air flow has bad odor.

5. Condensation on the front air grille of the indoor unit.

6. Water flowing out from the air conditioner unit.

7. Hissing air flow sound from the air conditioner unit during

operation.

If the fault persists, please call your local dealer / serviceman.

No Event CDF LED Timer LED Others LEDs Error Code

1 Room sensor open or short Blink 1 time - Blink Fan Blink E1

2 Indoor coil sensor open Blink 2 times - Blink Sleep Blink E2

3 Outdoor coil sensor open Blink 3 times - Blink Dry Blink E3

4 Compressor overload/

Indoor coil sensor short/ Blink 1 time Blink Cool Blink E4

Outdoor coil sensor short

5 Gas leak Blink 3 times Blink Cool & Dry Blink E5

6 Water pump fault Blink 2 times Blink Cool & Fan Blink E6

7 Outdoor defrost - Blink Heat -

8 Outdoor coil sensor exist Blink 5 times Blink Cool & Heat Blink E7

(MS model)

9 Hardware error (tact switch Blink 6 times Blink Heat, Cool, Blink E8

pin short) follow by Fan, Dry

Note: CDF LED : Cool/Dry/Fan LED, turns on in these modes

The unit will not detect sensor missing when the compressor is ON

1-16

MEMO

2-1

Français

CONTOUR ET DIMENSIONS

Unité Intérieure (Série 5CEE / CEE)

Toutes les dimensions sont données en mm

928

65

400

230

630

218

1080

Unité Extérieure (5SL / SL15C / CR)

LKL

N

C

M

(1,2)

30

A

D

O

(0,1)

3

B

(2,6)

65

(3,1)

80

N

F

E

C

G

H

JI

(0,7)

19

Dimension A B C D E F G H I J K L M N O

5SL / SL15C /CR 700 521 250 485 175 36 95 93 86 68 441 130 111 15 18

(27,5) (20,5) (9,8) (19,1) (6,8) (1,4) (3,7) (3,6) (3,3) (2,6) (17,3) (5,1) (4,3) (0,5) (0,7)

Toutes les dimensions sont

données en mm / (pouces)

2-2

Unité Extérieure (Série 5SL / SL)

Toutes les dimensions sont

données en mm / (pouces)

A

QP

P

M

N

15,0

39,0

R

A

D

C 5,0

E20,0

F

20,0

B

2,5

20,0

K

G

141,0

C5,0

160,0 H

L

64,5

J

Unité Extérieure (5SL / SL30C)

Toutes les dimensions sont

données en mm / (pouces)

745,5

25,0

141,0 141,0

20,0448,0

20,0

1030,0

852,0

45,8

62,3

400,0

40,0 40,0320,0

Dimension A B C D E F G H J K L M N P Q R

5SL / SL20C / CR

855

648

328 303 309

630

49 116 75 187 98 392 362 126 603 164

5SL / SL25C / CR

(33,7)

(25,5)

(12,9) (11,9) (12,2)

(24,8)

(1,9) (4,6) (3,0) (7,4) (3,9) (15,4) (14,3) (5,0) (23,7) (6,5)

5SL / SL28C / CR

750 730

(29,5) (28,7)

Страница загружается...

Acson 5SL, 5CEE Series, CR, SL15C, SL30C Инструкция по установке

Похожие модели бренда

Модели других брендов