Avermedia TV Box DVI 1080i Руководство пользователя

Бренд: Avermedia

Модель: TV Box DVI 1080i

Тип: Руководство пользователя

AVerTV DVI Box 1080i

User’s Manual

 English

 Pусский

FCC NOTICE (Class B)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Federal Communications Commission Statement

NOTE- This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

‧ Reorient or relocate the receiving antenna.

‧ Increase the separation between the equipment and receiver.

‧ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

‧ Consult the dealer or an experienced radio/television technician for help.

CAUTION ON MODIFICATIONS

To comply with the limits for the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must

be installed in computer equipment certified to comply with the Class B limits. All cables used to connect the

computer and peripherals must be shielded and grounded. Operation with non-certified computers or

non-shielded cables may result in interference to radio or television reception.

Changes and modifications not expressly approved by the manufacturer could void the user’s authority to

operate this equipment.

European Community Compliance Statement

Class B

This product is herewith confirmed to comply with the requirements set out in the

Council Directives on the Approximation of the laws of the Member States relating to

Electromagnetic Compatibility Directive 2004/108/EC.

Safety- Low Voltage Directive 2006/95/EC

DISCLAIMER

No warranty or representation, either expressed or implied, is made with respect to the contents of this

documentation, its quality, performance, merchantability, or fitness for a particular purpose. Information

presented in this documentation has been carefully checked for reliability; however, no responsibility is

assumed for inaccuracies. The information contained in this documentation is subject to change without notice.

In no event will AVerMedia be liable for direct, indirect, special, incidental, or consequential damages arising

out of the use or inability to use this product or documentation, even if advised of the possibility of such

damages.

TRADEMARKS

AVerMedia is registered trademarks of AVerMedia TECHNOLOGIES, Inc. IBM PC is a registered trademark of

International Business Machines Corporation. Macintosh is a registered trademark of Apple Computer, Inc.

Microsoft is a registered trademark and Windows is a trademark of Microsoft Corporation. All other products or

corporate names mentioned in this documentation are for identification and explanation purposes only, and

may be trademarks or registered trademarks of their respective owners.

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means

without the written permission of AVerMedia TECHNOLOGIES, Inc.

THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS PRODUCT MUST NOT BE

DISPOSED OF WITH YOUR OTHER HOUSEHOLD WASTE. INSTEAD, YOU NEED TO DISPOSE

OF THE WASTE EQUIPMENT BY HANDING IT OVER TO A DESIGNATED COLLECTION POINT

FOR THE RECYCLING OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT. FOR MORE

INFORMATION ABOUT WHERE TO DROP OFF YOUR WASTE EQUIPMENT FOR RECYCLING, PLEASE

CONTACT YOUR HOUSEHOLD WASTE DISPOSAL SERVICE OR THE SHOP WHERE YOU PURCHASED

THE PRODUCT.

№ РОСС TW.ME06.B05759

Срок действия с 24.01.2008г по 24.01.2011г

Москва

User’s Manual

ENG-1

English Polski Magyar Česky Slovenský Български Hrvatski Slovenščina

Table of Content

Chapter 1 What’s in the Package .......................................... ENG-2

Chapter 2 The Unit Parts........................................................ ENG-3

2.1 Touch Button Control Panel .........................................................ENG-3

2.2 Infrared Sensor............................................................................ENG-3

2.3 Connection Ports.........................................................................ENG-3

Chapter 3 Installation and Setup........................................... ENG-4

3.1 Using the AVerTV DVI Box 1080i.................................................ENG-5

3.2 The Remote Control ....................................................................ENG-5

3.3 Customizing the Picture Setting...................................................ENG-6

3.4 Supported Display Setting ...........................................................ENG-7

3.5 Supported Display Setting in PIP Mode.......................................ENG-7

Chapter 4 OSD Menu Settings............................................... ENG-8

4.1 Calling Up the MAIN MENU ........................................................ENG-8

4.2 Menu ...........................................................................................ENG-8

AVerMedia AVerTV DVI Box 1080i

ENG-2

Chapter 1 What’s in the Package

AVerMedia AVerTV DVI Box 1080i package contains the following items:

AVerMedia AVerTV DVI Box 1080i

DVI-D Cable

*Use the DVI-D cable to input or output the DVI signal.

Vertical Stand

’

User’s Manual

Remote Control

(with batteries)

Power Adapter Audio Cable

DVI-I to VGA adapter

User’s Manual

ENG-3

English Polski Magyar Česky Slovenský Български Hrvatski Slovenščina

Chapter 2 The Unit Parts

2.1 Touch Button Control Panel

The Touch Button Panel found on the top side of the unit provides quick access to commonly used functions.

Turn the unit on /off

Press this button to toggle between

TV/Video and PC display

Press Channel

to go up and Channel

to go down to the next active TV

channel. Use these buttons to make the

selection in the menu or picture setting

To call up the menu display

Press Volume to increase and

Volume

to decrease the volume

level . Use these buttons to adjust the

menu or picture setting

2.2 Infrared Sensor

When using the remote control, aim it at the Infrared Sensor which is located at the front panel of the unit.

2.3 Connection Ports

The port connectors allow connection of your TV antenna, PC, DVI monitor, VGA monitor (through DVI-I to VGA

Adapter) or LCD projector, speakers, video, or s-video source etc.

1 COMPOSITE VIDEO INPUT

2 Left & Right AUDIO INPUT

3 EARPHONE JACK

4 S-VIDEO INPUT

Front Panel

5 COMPONENT VIDEO INPUT

6 Speaker Connection

7 DVI OUTPUT to MONITOR (VGA

supported by DVI-I to VGA Adapter)

8 TV Antenna (75Ω)

9 DVI INPUT from PC (VGA supported

by DVI-I to VGA Adapter)

10 AUDIO INPUT from PC’s SOUND

CARD

Back Panel

11 POWER ADAPTER

The Installation and Setup section provides more information on cable connections.

AVerMedia AVerTV DVI Box 1080i

ENG-4

Chapter 3 Installation and Setup

The figure below shows the proper cable connections for installing AVerTV DVI Box 1080i and connecting it to your

audio/video equipment.

Please be noted if your signal input and output are not the same type, there will not be able

to detect the signal normally. Please make sure that your input and output are in the same

type (both DVI or both VGA(D-Sub)).

NOTE

User’s Manual

ENG-5

English Polski Magyar Česky Slovenský Български Hrvatski Slovenščina

3.1 Using the AVerTV DVI Box 1080i

The first time you power on the AVerTV DVI Box 1080i unit, it will automatically display the following menus:

Note: The text appeared in red is the currently selected setting.

LANGUAGE menu

LANGUAGE

ENGLISH

RUSSIAN

In this menu, choose the

language to use for the menus

and on-screen display (OSD).

CHANNEL SETUP menu

CHANNEL SETUP

CHANNEL

IDEO SYSTEM AUTO

FINE TUNING < 0 >

FAST TUNING YES

SAVE

FREQUENCY <49.75> Mhz

AUDIO SYSTEM1 D/K

AUDIO SYSTEM2 MONO

In this menu, change the TV

frequency assignments of certain

channels, fine tune TV channels,

etc. See details on each

configuration setting in the

CHANNEL SETUP menu.

To access various TV controls, open up the menu displays or press on the remote control buttons.

3.2 The Remote Control

The diagram below shows the remote control unit layout.

1.POWER

Turn the unit on/off

2.NUMBER

BUTTONS

To select a TV channel

3.CHANNEL

RETURN

Go to the previously selected channel

4.MENU

•

To call up the menu display

5.VOL ◄/►

* To increase and decrease volume level

* Use these button to adjust the menu or

picture setting

* In adjusting the PIP window position, use

these buttons to move the menu display to

the left and right of the screen.

6.OK

In the menu, press this button to confirm

the selection.

7.

To temporarily freeze the image on the

screen. Press the button again to

unfreeze the image.

8.PIP Pos.

To move the small TV/Video screen using

the CH▲, CH ▼, Vol◄, and Vol►

buttons in PIP mode. Press this button

again to exit the adjusting mode.

9.PIP

Switch between PIP*, PIP See-thru** and Full Screen mode

* To watch TV/Video in a small screen on an always on top of

the PC display.

** Make the small video screen semi-transparent allowing the

image behind the small screen show through.

10.MTS/ STEREO

If the channel offers the multi-language feature, press this

button to toggle between languages.

AVerMedia AVerTV DVI Box 1080i

ENG-6

11.PICTURE

To adjust brightness, contrast, color, tint or sharpness

Note: The Tint control will not work with a PAL/SECAM source.

12.PC BGM/ Res.

- Switch the audio source when in PC display mode

- Switch display resolution setting to 1024x768 when in

TV/Video mode

13.SOURCE

Switch between TV or external video sources

14.MUTE

To turn off /on the sound

15.PREVIEW

Display 13 consecutive TV channels on-screen.

16.CH▲/▼

*Go to the next or previous TV channel line up

*Use these buttons to make the selection in the menu or picture

setting

* In adjusting the PIP window position, use these buttons to

move the menu display up and down of the screen

17.SLEEP

To automatically turn off the unit after 30, 60, 90, 120 or 150

minutes.

18.TELETEXT(option)

This function is not available for this product.

19.FASTTEXT LINK buttons

(option)

This function is not available for this product.

20.AV/PC

To toggle between TV/ Video or PC display

3.3 Customizing the Picture Setting

CONTRAST

PICTURE

SCREEN RESOLUTION

PIP SIZE

SATURATION

SHARPNESS

SET DEFAULT

HUE

BRIGHTNESS

If you want to change the screen resolution, set the PIP

SIZE, or adjust the picture quality, press the PICTURE

button on the remote control. Then, you can use the CH▲ or

CH▼ button to select the items in the PICTURE menu; and

the Vol◄ or Vol ► button to open a submenu or make picture

setting adjustments.

To restore the picture default settings, select SET DEFAULT

and then press Vol ►.

1360X768

SCREEN RESOLUTION

1024X768

1280X1024

1440X900

1680X1050

1920X1200

1600X1200

1280X768

In the SCREEN RESOLUTION submenu, choose the desired

display resolution for your monitor screen. Press the CH▲ or

CH▼ button to move up or down the menu and select a

resolution, then press Vol ► to confirm your selection. If you

don’t confirm the selected resolution by pressing Vol ►

within 15 seconds, the resolution will keep at previous

resolution.

PIP SIZE

1/4

1/9

1/16

In the PIP SIZE submenu, choose the appropriate PIP

window ratio. Press the CH▲ or CH▼ button to make a

selection, then press Vol ► to confirm your selection.

User’s Manual

ENG-7

English Polski Magyar Česky Slovenský Български Hrvatski Slovenščina

3.4 Supported Display Setting

The reference table below lists the monitor display resolution and refresh rate settings that AVerTV DVI Box 1080i

supports.

Resolution 4:3 and PANORAMA support Refresh Rate (Hz)

1024x768 60

1280x768 O 60

1280x1024 60

1360x768 O 60

1440x900 O 60

1600x1200 60

1680x1050 O 60

1920x1200 O 60

3.5 Supported Display Setting in PIP Mode

The reference table below lists the monitor display resolution and refresh rate settings that AVerTV DVI Box 1080i

supports when viewing in PIP mode:

Note:

1. If the monitor does not support or is not set to the following mode listed below, it will switch back to

TV/Video mode.

2. If the computer switches to sleep mode, it will change back to TV/Video mode.

Resolution Refresh Rate (Hz)

1024 x 768 60, 70, 75

1280 x 768 60, 75

1280 x 1024 60, 75

1440 x 900 60, 75

1360 x 768 60

1680 x 1050 60

1600 x1200 60

Note:

YPbPr signal input format supports:

SDTV: 480i, 576i

HDTV: 480p@60Hz, 576p@50Hz, 720p@60Hz, 1080i@60Hz.

AVerMedia AVerTV DVI Box 1080i

ENG-8

Chapter 4 OSD Menu Settings

4.1 Calling Up the MAIN MENU

Press the MENU button on the remote control to open/close the MAIN MENU or a submenu. Then, you can use the

CH▲ or CH▼ button to select the items in the menu list; and the Vol◄ or Vol► button to adjust a setting. The next

table lists the different functions you will find in the MAIN MENU.

Note: The text appeared in red is the currently selected setting.

MAIN MENU

SOURCE

CHANNEL REMAPPING

CHANNEL SETUP

PICTURE

TIMER

SOUND

LANGUAGE

AUTO SCAN

FACTORY DEFAULT

OSD

4.2 Menu

User’s Manual

ENG-9

English Polski Magyar Česky Slovenský Български Hrvatski Slovenščina

MAIN

Submenus Usage

SOURCE

ANTENNA

VIDEO

S-VIDEO

YPBPR

In the SOURCE submenu, press CH▲ or CH▼ to select

ANTENNA, composite VIDEO, S-VIDEO or YPbPr as

your input source. Then press Vol► to confirm your

selection and return to the MAIN MENU.

AUTO SCAN

UTO SCAN

CHANNEL SCAN

FREQUENCY SCAN

Use CH▲ or CH▼ buttons to select between CHANNEL

SCAN and FREQUENCY SCAN. Press Vol► button to

make the selection. If you want to interrupt or cancel the

scanning process, press any button, but this will only

memorize the scanned channel.

These two types of channel-preset functions enable you to

memorize all active channels in your area.

Use the CHANNEL SCAN function first. If there are

channels missing after you perform CHANNEL SCAN,

use FREQUENCY SCAN function and repeat the

searching process.

NOTE: FREQUENCY SCAN is a very time consuming

process. If the default frequency table already includes all

active TV channels in your area, then avoid using the

FREQUENCY SCAN.

CHANNEL

SETUP

CHANNEL SETUP

CHANNEL

IDEO SYSTEM AUTO

FINE TUNING < 0 >

FAST TUNING YES

SAVE

FREQUENCY <49.75> Mhz

AUDIO SYSTEM1 D/K

AUDIO SYSTEM2 MONO

The CHANNEL SETUP menu allows you to change or

fine tune the TV frequency of channel numbers, choose

the video system used in your region, and more. (See the

"CHANNEL SETUP Menu" table for details.)

CHANNEL

REMAPPING

CHANNEL REMAPPING

2. 77.25MHz +

3. 175.25MHz +

4. ...... -

5. ...... -

6. ...... -

7. ...... -

8. ...... -

. ...... -

1. 49.75MHz +

The CHANNEL REMAPPING menu allows you to

reprogram channel numbers or enable/disable channels.

(See the "CHANNEL REMAPPING Menu" table for

details.)

PICTURE

CONTRAST

PICTURE

SCREEN RESOLUTION

PIP SIZE

SATURATION

SHARPNESS

SET DEFAULT

HUE

BRIGHTNESS

The PICTURE menu allows you to change the screen

resolution, set the PIP SIZE, or adjust the picture quality.

(See the "Customizing the Picture Settings" section for

details.)

SOUND

BALANCE < 0 >

SOUND SOURCE TUNER

The SOUND menu lets you select the sound source and

adjust your speakers. (See the "Sound Menu" table for

details.)

AVerMedia AVerTV DVI Box 1080i

ENG-10

TIMER

CURRENT TIME

ON TIMER

OFF TIMER

Press CH▲ or CH▼ button to select setting the current

time, on timer or off timer then press Vol►.

Use this function to set the current time, and to program

the unit to automatically turn on and off.

LANGUAGE

ENGLISH

RUSSIAN

The LANGUAGE menu sets the language to use for the

OSD menus.

Press CH▲ or CH▼ to select a language, then press

Vo l ► to confirm your selection.

FACTORY

DEFAULT

TIMER

CURRENT TIME

ON TIMER

OFF TIMER

FACTORY DEFAULT

YES

This menu allows you to revert settings back to the

default.

Select YES if you want to reset AVerTV DVI Box 1080i

back to the factory default settings. Otherwise, select NO

to keep the current settings. Then press Vol► to confirm

your selection.

OSD

TIMER

CURRENT TIME

ON TIMER

OFF TIMER

OSD

POSITION

BACKGROUND TRANSPARENCY

TEXT COLOR

OSD TIME

BACKGROUND COLOR

The OSD menu allows you to customize the color and

position of the OSD menus. (See the "OSD Menu" table

for details.)

CHANNEL SETUP Menu Settings Usage

CHANNEL SETUP

CHANNEL

IDEO SYSTEM AUTO

FINE TUNING < 0 >

FAST TUNING YES

SAVE

FREQUENCY <49.75> Mhz

AUDIO SYSTEM1 D/K

AUDIO SYSTEM2 MONO

CHANNEL

After selecting a frequency, choose a channel number to

assign to that frequency. Use the Vol◄ or Vol► button

when choosing a channel number.

Note: You can also use the CHANNEL setting to switch to

composite VIDEO, S-VIDEO or YPbPr.



FREQUENCY

Press the Vol◄ or Vol► button to scan down or up and

choose a TV frequency.

When FAST TUNING is disabled, pressing Vol◄ or Vol►

once changes the TV frequency by -/+ 0.25MHz; pressing

and holding down Vol◄ or Vol► continuously changes the

frequency by -/+ 0.25MHz and stops when an active channel

is found.

When FAST TUNING is enabled, pressing Vol◄ or Vol►

once goes to the next frequency that's in the TV frequency

table; pressing and holding down Vol◄ or Vol►

continuously scans through the frequencies in the TV

frequency table and stops when an active channel is found.

Note: After you have found a desired frequency, assign a

CHANNEL number, adjust FINE TUNING, and select a

VIDEO SYSTEM for that frequency. Then save your

settings before locating another TV frequency.

FINE

TUNING

If the reception of the selected channel is not clear, choose

FINE TUNING then press the Vol◄ or Vol► button until

the TV picture becomes clear.

User’s Manual

ENG-11

English Polski Magyar Česky Slovenský Български Hrvatski Slovenščina



VIDEO SYSTEM

Use the Vol◄ or Vol► button to select the video standard

used in your region. You can set this to AUTO to make

AVerTV DVI Box 1080i automatically detect the video

system, or you can manually choose between SECAM, PAL

or NTSC.

AUDIO

SYSTEM1

Use the Vol◄ or Vol► button to select the audio system.

You can choose between D/K or B/G.

AUDIO

SYSTEM 2

Use the Vol◄ or Vol► button to select the audio system.

You can choose between MONO, NICAM MONO, NICAM

STEREO, NICAM DUAL A, NICAM DUAL B, A2

MONO, A2 STEREO, A2 DUAL A or A2 DUAL B.

FAST

TUNING

Use the Vol◄ or Vol► button to enable or disable fast

tuning. Select YES if you want to enable fast tuning and

scan through available frequencies only in the TV frequency

table when you are choosing a frequency for a channel. By

default, NO is selected which allows you to scan through

frequencies at intervals of 0.25 MHz.

SAVE

When you have adjusted the frequency, fine tuning and/or

the video system setting, the SAVE item will show a

question mark (?). Press the Vol► button to change this item

to OK and save the settings.

Note: After selecting a TV frequency and assigning a

channel number, save the channel first before choosing a TV

frequency for another channel.

Channel Remapping Menu Usage

CHANNEL REMAPPING

2. 77.25MHz +

3. 175.25MHz +

4. ...... -

5. ...... -

6. ...... -

7. ...... -

8. ...... -

. ...... -

1. 49.75MHz +

This menu allows you to enable or disable a channel, reprogram or reassign

TV frequencies with channel numbers that are easier to remember.

A channel is enabled when there is a “+” sign indicated; a channel is disabled

when there is a “-“ sign indicated. To enable or disable a channel, press Vol◄.

To reassign a TV frequency to another channel number, first select the original

channel number and hold down the Vol► button. While the original channel

number is blinking, press CH▲ or CH▼ continuously until you reach the new

channel number. Then, press Vol►.

Sound Menu Settings Usage

SOUND

BALANCE < 0 >

SOUND SOURCE TUNER

SOUND SOURCE

Press Vol◄ or Vol► to switch the audio to TV

or your computer.

BALANCE

Press Vol◄ or Vol► to balance the sound of

your left and right speakers.

TIMER Menu Submenus Usage

CURRENT TIME

TIMERCURRENT TIME

HOUR 00

MINS 11

Press CH▲ or CH▼ button to select setting the

hour or mins.

To set the hour and mins, press Vol◄ or Vol► and

then press MENU button.

AVerMedia AVerTV DVI Box 1080i

ENG-12

ON TIMER

TIMERON TIMER

MINS

DAILY

TIMER

HOURS

OFF

Press CH▲ or CH▼ button to select setting the

hour, min, daily and timer.

-To set the hour and mins, press Vol◄ or Vol►.

-In Daily option, press Vol◄ or Vol► to select

ON to active this feature everyday or OFF to

active this feature only once.

-In Timer option, press Vol◄ or Vol► to select

ON to active this feature or OFF to deactivate this

feature.

-After doing all the settings, press MENU button.

OFF TIMER

TIMEROFF TIMER

OFF

0:30

1:00

1:30

2:00

2:30

The TIMER menu allows you to set the time

interval for the TV’s sleep timer.

Press CH▲ or CH▼ to select a time interval, then

press Vol► to confirm your selection. AVerTV

DVI Box 1080i will automatically switch to sleep

mode when it has been left idle for the specified

time interval. (By default, the timer is disabled.)

OSD Menu Submenus Usage

BACKGROUND

TRANSPARENCY

TIMERBACKGROUND TRANSPARENCY

100%

25%

50%

75%

This sets the transparency of the OSD menus

against the TV image.

Press CH▲ or CH▼ to choose the desired

transparency level. 25% is the most transparent,

while 100% displays the OSD menus clear and

solid in color. After you have made your selection,

press the Vol► button.

TEXT COLOR

TIMERTEXT COLOR

BODY

MESSAGE

SAVE

TITLE

<CYAN>

<WHITE>

This sets the color of the following text:

TITLE : Color of the menu name

BODY : Color of menu items

MESSAGE : Color of the hint messages at the

bottom of the menus

Use the CH▲ or CH▼ button to select the type of

text whose color you want to change. Then use the

Vo l ◄ or Vol► button to browse through the

available colors and select a desired color.

BACKGROUND

COLOR

TIMERBACKGROUND COLOR

BODY

MESSAGE

SAVE

TITLE

<WHITE>

<BLACK>

This sets the color of the following backgrounds:

TITLE : Color of the title bar on top of the menus

BODY : Background color of menu list

MESSAGE : Color of the message bar at the

bottom of the menus

Use the CH▲ or CH▼ button to select the type of

background whose color you want to change. Then

use the Vol◄ or Vol► button to browse through

the available colors and select a desired color.

POSITION

This allows you to adjust the position of OSD

menus on the monitor screen.

Press CH▲ to move the menu display up, CH▼ to

move down, Vol◄ to move to the left, or Vol► to

move to the right.

OSD TIME

TIMEROSD TIME

15 SEC

5 SEC

10 SEC

This sets the duration for displaying the OSD

menus.

Press CH▲ or CH▼ to choose the desired

duration. After you have made your selection,

press the Vol► button.

Руководство пользователя

RUS-1

English Pусский Magyar Česky Slovenský Български Hrvatski Slovenščina

Оглавление

Глава 1 Комплект поставки.............................................. RUS-2

Глава 2 Устройство тюнера ............................................. RUS-3

2.1 Назначение кнопок на корпусе тюнера .................................... RUS-3

2.2 Инфракрасный приёмник ..........................................................RUS-3

2.3 Входы/выходы............................................................................RUS-3

Глава 3 Установка и подключение ................................. RUS-4

3.1 Настройка AVerTV DVI Box 1080i ..............................................RUS-5

3.2 Пульт ДУ.....................................................................................RUS-5

3.3 Персональные настройки изображения................................... RUS-6

3.4 Поддерживаемые параметры экрана.......................................RUS-7

3.5 Поддерживаемые настройки экрана в режиме PIP.................RUS-7

Глава 4 Навигация и выполнение настроек в экранном

меню ...................................................................... RUS-8

4.1 Вызов главного меню ................................................................ RUS-8

4.2 Структура экранного меню........................................................RUS-8

AVerMedia AVerTV DVI Box 1080i

RUS-2

Глава 1 Комплект поставки

В комплект поставки AVerMedia AVerTV DVI Box 1080i входит:

AVerMedia AVerTV DVI Box 1080i

DVI-D кабель

*Для ввода или вывода DVI сигнала

Подставка

’

Руководство пользователя

Пульт ДУ

(с батарейками)

Блок питания Аудиокабель

DVI-I - VGA переходник

Руководство пользователя

RUS-3

English Pусский Magyar Česky Slovenský Български Hrvatski Slovenščina

Глава 2 Устройство тюнера

2.1 Назначение кнопок на корпусе тюнера

Кнопки управления на корпусе тюнера предоставляют оперативный доступ к наиболее часто используемым

функциям.

Кнопка включения / выключения

Выбор источника сигнала (ТВ, видео

или компьютер).

Переключение каналов. Выбор

элемента экранного меню.

Вызов экранного меню.

Регулировка громкости. Изменение

значения элемента экранного меню.

2.2 Инфракрасный приёмник

При использовании пульта ДУ, направляйте его в сторону инфракрасного датчика на передней панеле

устройства.

2.3 Входы/выходы

Разъемы входов/выходов тюнера позволяют подключать к нему ТВ антенну, компьютер, DVI монитор, VGA

монитор (с помощью DVI-I - VGA переходника) или LCD проектор, активные колонки, источники VHS или

S-VHS сигнала и т.д.

1 Композитный видеовход

2 Аудиовход (левый и правый каналы)

3 Аудиовыход на наушники

4 S-Video видеовход

Передняя панель

5 Компонентный видеовход

6 Аудиовыход для подключения колонок

7 Выход DVI для подключения к

монитору. (Подключение

VGA-монитора возможно с помощью

DVI-I - VGA переходника)

8 ТВ антенна (75Ω)

9 Вход DVI для подключения компьютера.

(Подключение VGA-монитора

возможно с помощью DVI-I - VGA

переходника)

10 Аудиовход с компьютера

Задняя панель

11 Гнездо питания

Раздел «Уст ановка и подключение» предоставляет дополнительную информацию по подключению тюнера.

AVerMedia AVerTV DVI Box 1080i

RUS-4

Глава 3 Установка и подключение

На рисунке, приведённом ниже, показана схема соединения AVerTV DVI Box 1080i с внешними аудио/видео

устройствами.

Просьба учесть, что, в случае использования разных входных/выходных портов при

подключении внешних устройств к тюнеру, корректный прием сигнала невозможен.

Пожалуйста, убедитесь в том, что порты входных и выходных сигналов обеих устройств

одинакового типа (оба DVI или оба VGA (D-Sub)).

Примечание

Страница загружается ...

Avermedia TV Box DVI 1080i Руководство пользователя

Бренд: Avermedia

Модель: TV Box DVI 1080i

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

на других языках

English: Avermedia TV Box DVI 1080i User manual

Avermedia TV Box DVI 1080i Руководство пользователя

Avermedia TV Box DVI 1080i Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов