Yamaha T-D500 Инструкция по применению

©

2010 Yamaha Corporation

Tuner

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

G

Printed in China CQX1A1548Z

00_T-S500_G-cv.fm Page 1 Friday, July 16, 2010 1:21 PM

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place –

away from direct sunlight, heat sources, vibration, dust,

moisture, and/or cold. For proper ventilation, allow the

following minimum clearances.

Top : 10 cm (4 in)

Rear: 10 cm (4 in)

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

18 Before moving this unit, press A to set this unit to the standby

mode, and disconnect the AC power plug from the wall outlet.

19

Condensation will form when the

surrounding temperature

changes suddenly. Disconnect the power cable from the outlet,

then leave this unit alone.

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire, or the like. When you dispose of batteries,

follow your regional regulations.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you set this unit to standby mode by A. In this state,

this unit is designed to consume a very small quantity

of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or

coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

1 En

English

PREPARATION

OPERATIONS

ADDITIONAL

INFORMATION

REMOTE CONTROL AND FRONT PANEL.... 2

CONNECTIONS .................................................... 4

DAB TUNING......................................................... 5

Preparing the DAB tuning ......................................... 5

Manual tuning............................................................ 6

Presetting DAB stations............................................. 7

Using the DAB functions........................................... 8

DAB station information ......................................... 10

DAB frequency information.................................... 10

FM/AM TUNING ................................................. 11

Automatic and manual tuning.................................. 11

Presetting stations .................................................... 12

Receiving Radio Data System information

(FM stations only) ............................................... 13

TP Search function (FM stations only).................... 15

Using the FM/AM functions.................................... 15

TROUBLESHOOTING .......................................16

SPECIFICATIONS...............................................18

CONTENTS

PREPARATION

OPERATIONS

ADDITIONAL INFORMATION

■ Features

DAB (Digital Audio Broadcasting)/DAB+ tuner

◆

Automatic scanning function to locate all DAB stations in your

area

◆ DLS (Dynamic Label Segment) information display

◆ Tuning aid function to optimize DAB reception

◆ 40 DAB/DAB+ station preset tuning

◆ Coaxial and optical digital audio output capability for DAB

audio signals

Sophisticated FM/AM tuner

◆ 30-station (each band) FM/AM preset tuning

◆ Automatic preset tuning

◆ Radio Data System text information display capability

■ Supplied accessories

Please check that you have received all of the following parts.

■ About this manual

• y indicates a tip for your operation.

• This manual describes how to operate this unit using a remote control except when it is not available. Some of these

operations are also available using the front panel.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of

improvements, etc. In case of differences between the manual and the product, the product has priority.

Remote control Indoor FM antenna AM loop antenna

Indoor DAB antenna

Battery (CR2025) RCA stereo cable

2 En

PREPARATION

1 Infrared transmitter

Outputs infrared controls signals. Aim this transmitter at

the component you want to operate.

2 FM MODE

Switches the FM radio wave reception mode (stereo or

monaural) when this unit is in the FM tuning mode (see

page 11).

3 DIMMER

Changes brightness level of the front panel display.

Choose brightness from 3 levels by pressing this button

repeatedly.

y

This setting is retained even if you turn off this unit.

4 PRESET F / G

Switches the preset stations.

5 MEMORY

Sets this unit to the preset station memory mode (see

pages 7, 12).

6 B / C / D / E, ENTER

Selects and confirms an item.

7 INFO/TEXT

Turns on and changes the DAB station information (see

page 10) or Radio Data System display mode (see page

13) on the front panel display.

8 Numeric buttons, ENTER

Selects the desired preset stations (see pages 7, 12).

y

To enter number less than 10 (i.e. 1 to 9), press the desired

number and then ENTER, or press 0 and then enter the desired

number.

REMOTE CONTROL AND FRONT PANEL

English

3 En

PREPARATION

REMOTE CONTROL AND FRONT PANEL

9 BAND

Selects the reception band (DAB, FM, or AM).

0 AUTO SCAN

Starts the automatic scanning function (see pages 6, 12).

A A (standby/on)

Turns on this unit. Press this button again to set this unit to

the standby mode.

y

The standby/on indicator lamp above lights up when this unit is

turned on.

In the standby mode, this unit consumes a small amount of power

in order to receive infrared signals from the remote control.

B TUNING H / I

• Selects the desired frequency when you press this

button.

• Searches the next FM or AM station when you press

and hold this button for more than 2 seconds.

C TP

Searches automatically for a station broadcasting a traffic

program (TP) (see page 15).

D FUNCTION

Activates the function set up menu (see pages 8, 15).

E CLEAR

• Clears a preset station (see pages 8, 13).

• Clears all station information and preset settings in the

DAB tuning mode when you press and hold this button

for more than 3 seconds (see page 9).

• Clears all preset stations in the FM or AM tuning mode

when you press and hold this button for more than

3 seconds (see page 13).

F STEREO indicator

Lights up when this unit is in the stereo playback.

G TUNED indicator

Lights up when this unit is tuned into a station.

H Multi-information display

Displays tuning status messages and the DAB station or

Radio Data System information.

I TP indicator lamp

Lights up when a Traffic Program (TP) station is received

(see page 15).

J SECONDARY indicator

Lights up when this unit is in the DAB tuning mode and

receiving a secondary station.

K TUNING MODE

Selects the tuning mode (automatic, manual, or preset

tuning).

L PRESET/TUNING

• Searches the next FM or AM station when this unit is

in the automatic tuning mode.

• Selects the desired frequency when this unit is in the

manual tuning mode.

• Switches the preset stations when this unit is in the

preset tuning mode.

■ Using the remote control

Use the remote control within 6 m (20 ft) of this unit and

point it toward the remote control sensor. It receives

signals from a remote control provided with a Yamaha

amplifier or AV receiver.

• Do not spill liquid on the remote control.

• Do not drop the remote control.

• Do not leave the remote control in the following places:

– hot or humid places such as a bathroom or near heater

– extremely cold places

– dusty places

■ Installing the battery in the remote

control

Change the battery when the operation range of the remote

control decreases.

• Keep the battery out of the reach of children, so that it

is not mistakenly swallowed.

• Insert the battery according to the polarity markings.

Note

Notes

CAUTION

30º 30º

Approximately

6 m (20 ft)

Remote control

sensor

Straight pin

Battery (CR2025)

(supplied)

4 En

■ Assembling the supplied AM loop

antenna

■ Connecting the wire of the AM loop

antenna

CONNECTIONS

Indoor FM

antenna

(supplied)

AM loop antenna (supplied)

• The AM loop antenna should always be connected, even if

an outdoor AM antenna is connected to this unit.

• The AM loop antenna should be placed away from this

unit.

Outdoor AM antenna

Use a 5 to 10 m of vinyl

covered wire extended

outdoors from a window.

Ground

For maximum safety and minimum interference, connect the

antenna GND terminal to a good earth ground.

A good earth ground is a metal stake driven into moist earth.

RCA stereo

cable

(supplied)

Do not connect power

cable until all cable

connection are complete.

CAUTION

Analog audio

input

If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center

about outdoor antennas.

Note

Amplifier

To the AC wall outlet

y

It is recommended that you use the

Tune Aid function in order to

maximize DAB reception capability

(see page 9).

Indoor DAB antenna (supplied)

Stretch out the antenna and place it to

find the best reception position then fix it.

Digital audio

input

The DIGITAL RADIO OUTPUT jacks (OPTICAL

and COAXIAL) output the digital audio signals

(PCM signals) when this unit is in the DAB tuning

mode. DAB audio signals are also output the

ANALOG OUTPUT jack of this unit. FM or AM

audio signals are not output at the DIGITAL

RADIO OUTPUT jacks.

Note

Optical

cable

Coaxial digital

audio cable

black

white

English

5 En

OPERATIONS

DAB (Digital Audio Broadcasting) uses digital signals for

clearer sound and more stable reception compared to

analog signals.

DAB is broadcasted in blocks of data called “ensembles”

containing up to several radio stations that are

simultaneously broadcasted.

DAB can also include an extensive amount of text

information - called DLS (Dynamic Label Segment, see

page 10) - which is displayed on the front panel display of

the unit, enabling you to select a station by name.

DAB+ is a standard for digital radio broadcasts that uses

the MPEG4 HE-AAC v2 audio format and provides

higher quality sound than DAB.

• Be sure to check the DAB coverage in your area in that not all

areas are currently being covered. For a list of nationwide DAB

statuses and worldwide DAB frequencies, check WorldDMB

online at http://www.worlddab.org/.

• The sound quality and station information are controlled by the

DAB broadcaster, not this unit. Not all DAB broadcasters

transmit station information.

• DAB signals are broadcast in Band III (174 - 240 MHz) and

L Band (1452 - 1492 MHz).

Before tuning into DAB stations, you must perform the

automatic scanning. The scanning starts automatically

when you select DAB as the input source for the first time.

Press BAND repeatedly to select DAB as the

reception band.

The scanning starts automatically.

The number of channels found is displayed on the front

panel display.

Once the scanning is complete, this unit is tuned into the

first DAB station in the registry list.

DAB TUNING

Notes

Preparing the DAB tuning

If the automatic scanning operation is not

successful...

“No stations Available” and then following is

displayed on the front panel display.

1 Press B / C to select “Tune Aid” or

“Autoscan”.

2 Press E or ENTER.

The selected function (“Tune Aid” or “Autoscan”)

starts.

y

• For details on the Tune Aid function, see page 9.

• For details on the Autoscan Full function, see page 6.

• For further details about problems and their remedies, see

page 16.

BAND

AUTO SCAN

6 En

DAB TUNING

■ Using the automatic scanning function

Use the automatic scanning function to scan the DAB

station again.

Autoscan Full (Full range scanning)

This unit scans the entire range of Band III and L Band

(see page 10).

Press and hold AUTO SCAN for more than 2

seconds.

This unit starts the full range scanning. “Autoscan Full” is

displayed on the front panel display.

Once this unit has finished scanning, this unit is tuned into

the first DAB station in the registry list.

Autoscan Local (Local range scanning)

This unit scans the limited range of Band III.

Press AUTO SCAN.

This unit starts the local range scanning. “Autoscan

Local” is displayed on the front panel display.

Once this unit has finished scanning, this unit is tuned into

the first DAB station in the registry list.

Use this feature to select the desired DAB station by

browsing the registry list.

Once you have performed the automatic scanning, the registry list

of available stations is updated automatically as long as this unit

is in the DAB tuning mode. To register new ensembles, use the

automatic scanning function (see page 5).

1 Press BAND repeatedly to select DAB as the

reception band.

2 Press TUNING H / I to select the desired

DAB station.

When this unit tuned into a station, the TUNED

indicator lights up.

y

On the front panel, press TUNING MODE repeatedly to

select “Manual tune” and then rotate PRESET/TUNING.

If the selected DAB station is a secondary station, the

SECONDARY indicator lights up.

“Off air” is displayed when this unit can not receive the specified

DAB station.

y

You can change the order of the DAB stations listen in the

registry listed by using the “Station order” function (see page 8).

Manual tuning

Note

PRESET/

TUNING

BAND

TUNING H / I

TUNING

MODE

BAND

Current DAB station SECONDARY indicator

English

7 En

OPERATIONS

DAB TUNING

You can tune into stations easily by storing (presetting)

and recalling them. This function enables this unit to

preset up to 40 DAB stations.

■ Storing DAB stations

1 Tune into the desired DAB station.

See page 6 for tuning instructions.

2 Press MEMORY.

The preset number blinks on the front panel display

for 10 seconds.

Perform the next operation within 10 seconds after pressing

MEMORY.

3 Press PRESET F / G or the numeric buttons

to select the desired preset number while the

preset number blinks.

y

On the front panel, rotate PRESET/TUNING.

Perform the next operation within 10 seconds after selecting

the preset number.

4 Press MEMORY or ENTER to confirm the

preset.

When you preset a new station to an existing preset number, new

preset data will overwrite the existing preset data.

y

To clear the preset DAB station, see “Clearing the preset DAB

station” on page 8.

■ Recalling the preset DAB stations

You can tune into any desired station simply by selecting

the preset number.

1 Press BAND repeatedly to select DAB as the

reception band.

2 Press PRESET F / G or the numeric buttons

to select the desired preset number.

When this unit is tuned into the selected station, the

TUNED indicator lights up.

y

• On the front panel, press TUNING MODE repeatedly to

select “Preset tune” and then rotate PRESET/TUNING.

• “CHXX Empty” (XX indicates the preset number) is

displayed briefly when no preset DAB station is assigned

to the corresponding preset number. The DAB station

currently being received is then displayed on the front

panel display.

Presetting DAB stations

Note

MEMORY

PRESET/

TUNING

ENTER

CLEAR

BAND

PRESET F / G

Numeric

buttons

CLEAR

Note

8 En

DAB TUNING

■ Clearing the preset DAB station

Follow the steps below to clear a preset DAB station one

at a time.

1 Select the desired preset number.

See “Recalling the preset DAB stations” on page 7.

2 Press CLEAR.

The selected preset number blinks on the front panel

display.

If you do not perform the next operation within 10 seconds,

the clearing is canceled.

3 Press CLEAR again to confirm.

“CHXX cleared” (XX indicates the preset number) is

displayed on the front panel display.

y

• To clear all preset DAB stations, press and hold CLEAR

for more than 3 seconds. After all preset DAB stations are

cleared, the Autoscan Full function starts automatically

(see page 6).

• You can also clear all preset DAB stations by using the

DAB functions. See “DAB Clear” on page 9.

Use this feature to set the DAB functions.

1 Press BAND repeatedly to select DAB as the

reception band.

2 Press FUNCTION.

The DAB function menu is displayed on the front

panel display.

3 Press B / C to select the desired DAB

function and then press E or ENTER.

You can select the following functions.

• Station Order (see page 8)

• Tune Aid (see page 9)

• Dynamic Range (see page 9)

• DAB Clear (see page 9)

• Auto Power Down (see page 9)

y

To exit from the DAB function menu, press FUNCTION again or

press D.

■ Station Order

You can change the order of the registered DAB stations.

1 Select “Station Order” in the DAB function

menu.

Note

Using the DAB functions

FUNCTION

BAND

B / C / D / E

/ENTER

English

9 En

OPERATIONS

DAB TUNING

2 Press B / C to select the desired station

order setting and then press ENTER.

y

While pressing B / C to select the desired setting, “*” is

displayed next to the current setting.

■ Tune Aid

Measure reception strength of the received signal (from 0

(none) to 100 (best)).

1 Select “Tune Aid” in the DAB function menu.

2 Press B / C to select the desired DAB

channel.

The strength of the selected DAB channel signal is

displayed on the front panel display. Adjust the

orientation of the DAB antenna so that the strength of

the selected DAB channel signal gets stronger.

■ Dynamic Range

You can change the dynamic range compression setting.

This is especially useful when you listen to a DAB station

in a noisy environment or at a low volume at night.

1 Select “Dynamic Range” in the DAB function

menu.

2 Press B / C to select the desired dynamic

range compression setting and then press E

or ENTER.

y

While pressing B / C to select the desired setting, “*” is

displayed next to the current setting.

■ DAB Clear

Clears all DAB station information and preset settings

stored in the unit.

y

You can also perform DAB Clear by pressing and holding

CLEAR for more than 3 seconds in the preset tuning mode. See

“Clearing the preset DAB station” on page 8.

Once DAB Clear is performed, the deleted information and preset

settings cannot be restored.

1 Select “DAB Clear” in the DAB function

menu.

2 Press B / C to select “OK” and then press E

or ENTER.

After DAB Clear is complete, the Autoscan Full

function starts automatically (see page 6).

y

To cancel the operation, select “CANCEL”.

■ Auto Power Down

This unit automatically enters standby mode if it is not

operated for specified amount of time.

This setting is effective for all tuning modes.

1 Select “Auto Power Down” in the DAB

function menu.

2 Press B / C to select the desired auto power

down setting and then press E or ENTER.

y

While pressing B / C to select the desired setting, “*” is

displayed next to the current setting.

Choice Description

Alphanumeric

Default setting. Stations are listed in the

alphanumeric order.

Active

This unit lists the currently active DAB

stations first, and then other DAB

stations in the alphanumeric order.

Ensemble

Select this setting to browse through the

registered DAB stations from the lowest

to the highest channel labels (see page

10).

Choice Description

AUTO

Default setting. This unit utilizes the

dynamic range compression

automatically if it is transmitted.

OFF

This unit does not utilize the dynamic

range compression.

Note

Choice Description

OFF

This unit will not be set to standby

mode automatically.

4 Hours,

8 Hours,

12 Hours

This unit is set to standby mode

automatically after the specified

amount of time passes.

Default setting is “8 Hours”.

10 En

DAB TUNING

Use this feature to display various information about the

current DAB station.

1 Tune into the desired DAB station.

2 Press INFO/TEXT repeatedly to display

information about the current DAB station.

DLS (Dynamic Label Segment)

Displays information about the current DAB station, such

as the name of the song, artist and speaker, etc. This data

is continuously updated by the DAB broadcaster, thus

changing often with every new song or program. Other

data, such as news, weather, and sports headlines, may be

broadcast as well.

Audio mode

Displays bit rate and digital radio format (DAB or DAB+).

Program type

Displays the genre of the current DAB station.

Ensemble label

Displays the name of the current ensemble.

Date & time

Displays the current date and time.

Channel & frequency

Displays the channel label and frequency of the current

DAB station (See page 10).

Signal quality

Displays the signal reception quality (from 0 (none) to 100

(best)) of the current DAB station.

y

The front panel display can display up to 16 alphanumeric

characters at once. The dynamic label segment scrolls in a

continuous manner.

■ Band III

When you perform the local range scanning, this unit scans only

within the frequencies marked with an asterisk (*) in the

following table (see page 6).

■ L Band

DAB station information

INFO/TEXT

DAB frequency information

Note

Frequency

Channel

label

Frequency

Channel

label

174.928 MHz 5A * 208.064 MHz 9D

176.640 MHz 5B * 209.936 MHz 10A

178.352 MHz 5C * 211.648 MHz 10B

180.064 MHz 5D * 213.360 MHz 10C

181.936 MHz 6A * 215.072 MHz 10D

183.648 MHz 6B * 216.928 MHz 11A

185.360 MHz 6C * 218.640 MHz 11B

187.072 MHz 6D * 220.352 MHz 11C

188.928 MHz 7A * 222.064 MHz 11D

190.640 MHz 7B * 223.936 MHz 12A

192.352 MHz 7C * 225.648 MHz 12B

194.064 MHz 7D * 227.360 MHz 12C

195.936 MHz 8A * 229.072 MHz 12D

197.648 MHz 8B * 230.784 MHz 13A

199.360 MHz 8C * 232.496 MHz 13B

201.072 MHz 8D * 234.208 MHz 13C

* 202.928 MHz 9A * 235.776 MHz 13D

* 204.640 MHz 9B * 237.488 MHz 13E

* 206.352 MHz 9C * 239.200 MHz 13F

Frequency

Channel

label

Frequency

Channel

label

1452.960 MHz LA 1473.504 MHz LM

1454.672 MHz LB 1475.216 MHz LN

1456.384 MHz LC 1476.928 MHz LO

1458.096 MHz LD 1478.640 MHz LP

1459.808 MHz LE 1480.352 MHz LQ

1461.520 MHz LF 1482.064 MHz LR

1463.232 MHz LG 1483.776 MHz LS

1464.944 MHz LH 1485.488 MHz LT

1466.656 MHz LI 1487.200 MHz LU

1468.368 MHz LJ 1488.912 MHz LV

1470.080 MHz LK 1490.624 MHz LW

1471.792 MHz LL

English

11 En

OPERATIONS

■ Automatic tuning

Automatic tuning is effective when station signals are

strong and there is no interference.

1 Press BAND repeatedly to select FM or AM

as the reception band.

2 Press and hold TUNING H / I for more than

2 seconds to begin automatic tuning.

When this unit is tuned into a station, the TUNED

indicator lights up and the frequency of the station is

displayed on the front panel display.

y

• On the front panel, press TUNING MODE repeatedly to

select “Auto tune” and then rotate PRESET/TUNING.

• If the station provides Radio Data System information, the

program service information will be displayed on the front

panel display (see page 13).

■ Manual tuning

If the signal from the station you want to select is weak,

tune into it manually.

1 Press BAND repeatedly to select FM or AM

as the reception band.

2 Press TUNING H / I to select the desired

frequency.

When this unit is tuned into a station, the TUNED

indicator lights up.

y

On the front panel, press TUNING MODE repeatedly to

select “Manual tune” and then rotate PRESET/TUNING.

■ Improving FM reception

If the signal from the station is weak and the sound quality

is not good, set the FM radio wave reception mode to the

monaural tuning mode to improve reception.

Press FM MODE repeatedly to select “AUTO

STEREO” (stereo mode) or “MONO” (monaural

mode) when this unit is tuned into an FM radio

station.

• When this unit is in the stereo tuning mode, the

STEREO indicator lights up on the front panel display.

• When this unit is in the monaural tuning mode, the

STEREO indicator goes off.

Even if this unit is in the stereo tuning mode, the STEREO

indicator does not light up when the current program is monaural.

FM/AM TUNING

Automatic and manual tuning

FM MODE

BAND

TUNING

MODE

PRESET/

TUNING

TUNING H / I

FM MODE

BAND

Note

12 En

FM/AM TUNING

You can tune into stations easily by storing (presetting)

and recalling them. This function enables this unit to

preset up to 30 stations for each band.

■ Automatic station preset

1 Press BAND repeatedly to select FM or AM

as the reception band.

2 Press AUTO SCAN.

“Auto Preset” blinks on the front panel display. This

unit starts searching the stations with strong signals

and stores them automatically.

When automatic station preset is completed, this unit

tunes into the station preset to “01”.

• FM or AM with sufficient signal strength are stored

automatically. To store a station with weak signal strength, store

it manually. See “Manual station preset” below.

• When you rerun “Automatic station preset”, all of the preset

data will be deleted and new preset data will be set to each

preset number.

• If no station is found, the search ends and this unit returns to the

previous station tuned in before the search.

■ Manual station preset

1 Tune into the desired FM/AM station.

See page 11 for tuning instructions.

2 Press MEMORY.

The preset number blinks on the front panel display

for 10 seconds.

Perform the next operation within 10 seconds after pressing

MEMORY.

3 Press PRESET F / G or the numeric buttons

to select the desired preset number while the

preset number blinks.

y

On the front panel, rotate PRESET/TUNING.

Perform the next operation within 10 seconds after selecting

the preset number.

4 Press MEMORY or ENTER to confirm the

preset.

• When you preset a new station to an existing preset number,

new preset data will overwrite the existing preset data.

• The reception mode (stereo or monaural) is stored along with

the station frequency.

■ Recalling preset stations

You can tune into any desired station simply by selecting

the preset number.

1 Press BAND repeatedly to select FM or AM

as the reception band.

2 Press PRESET F / G or the numeric buttons

to select the desired preset number.

y

• On the front panel, press TUNING MODE repeatedly to

select “Preset tune” and then rotate PRESET/TUNING.

• “CHXX Empty” (XX indicates the preset number) is

displayed briefly when no preset FM or AM station is

assigned to the corresponding preset number. The FM or

AM station currently being received is then displayed on

the front panel display.

Presetting stations

Notes

PRESET/

TUNING

BAND

PRESET F / G

BAND

CLEAR

MEMORY

AUTO SCAN

MEMORY

AUTO SCAN

Numeric

buttons

ENTER

CLEAR

Note

Notes

Preset number

English

13 En

OPERATIONS

FM/AM TUNING

■ Clearing the preset FM or AM station

Follow the steps below to clear a preset FM or AM station

one at a time.

1 Select the desired preset number.

See “Recalling preset stations” on page 12.

2 Press CLEAR.

The selected preset number blinks on the front panel

display.

If you do not perform the next operation within 10 seconds,

the clearing is canceled.

3 Press CLEAR to confirm.

“CHXX cleared” (XX indicates the preset number) is

displayed on the front panel display.

y

• To clear all preset FM or AM stations, press and hold CLEAR

for more than 3 seconds.

• You can also clear all preset FM or AM stations, by using the

FM/AM functions. See “Presets Clear” on page 15.

Radio Data System is a data transmission system used by

FM stations in many countries. This unit can receive four

types of Radio Data System data information: Program

Service, Program Type, Radio Text, and Clock Time.

1 Tune into the desired Radio Data System

broadcasting station.

2 Press INFO/TEXT repeatedly to select the

desired Radio Data System display mode.

When you select “PROGRAM TYPE”, the following

program type names are displayed.

Note

Receiving Radio Data System

information (FM stations only)

Choice Description

PROGRAM SERVICE Default setting. This unit

displays the name of the Radio

Data System program currently

being received.

PROGRAM TYPE This unit displays the type of

the Radio Data System

program currently being

received.

RADIO TEXT This unit displays the

information on the Radio Data

System program currently

being received.

CLOCK TIME This unit displays the current

time.

INFO/TEXT

14 En

FM/AM TUNING

• It may take a while for this unit to receive all of the Radio Data

System data from the station.

• If the signals being received are not strong enough, this unit

may not be able to utilize the Radio Data System data. In

particular, the “RADIO TEXT” mode requires a large amount

of data and may not be available even when the other Radio

Data System display modes are available.

• In case of poor reception condition, press FM MODE to select

the monaural reception mode (see page 11).

• If the signal strength is weakened by external interference while

this unit is receiving the Radio Data System data, the reception

may be cut off unexpectedly.

• When the “RADIO TEXT” mode is selected, this unit can

display the program information by a maximum of

128 alphanumeric characters, including the umlaut symbol.

Unavailable characters are displayed with the “_” (underscore).

The displayed information scrolls continuously.

Program type Description

News News

Current Affairs Current Affairs

Information General Information

Sport Sports

Education Education

Drama Drama

Cultures Cultures

Science Science

Varied Speech Varied Speech

Pop Music Pop Music

Rock Music Rock Music

Easy Listening Easy Listening

Light Classics M Light Classical Music

Serious Classics Serious Classical Music

Other Music Other Music

Weather & Metr Weather &

Meteorology

Finance Finance

Children s Progs

Children’s Program

Social Affairs Social Affairs

Religion Religion

Phone In Phone In

Travel & Touring Travel & Touring

Leisure & Hobby Leisure & Hobby

Jazz Music Jazz Music

Country Music Country Music

National Music National Music

Oldies Music Oldies Music

Folk Music Folk Music

Documentary Documentary

Alarm Test Alarm Test

Alarm-Alarm! Alarm-Alarm!

'

Notes

English

15 En

OPERATIONS

FM/AM TUNING

This unit can automatically search Radio Data System

stations that are broadcasting a traffic program (TP).

Press TP.

“TP SEARCH ” blinks on the front panel display

for 3 seconds and search starts automatically.

When a TP station is received, TP indicator lamp

lights up and TP search finishes.

y

If the station provides Radio Data System information, the

program service information will be displayed on the front panel

display.

To search the next TP station, press TP.

• Press TP during TP search to cancel.

• If no TP Stations are found, “NO TP STATION” is displayed on

the front panel display and this unit returns to the state before

searching.

Use this feature to set the FM/AM functions.

1 Press BAND repeatedly to select FM or AM

as the reception band.

2 Press FUNCTION.

The FM/AM function menu is displayed on the front

panel display.

3 Press B / C to select desired FM/AM function

and then press E or ENTER.

You can select the following functions.

• Presets Clear (see page 15)

• Auto Power Down (see page 15)

y

To exit from the FM/AM function menu, press FUNCTION

again or press D.

■ Presets Clear

Clears all preset settings stored in the unit for the current

tuning mode.

y

You can also perform Presets Clear by pressing and holding

CLEAR for more than 3 seconds in the preset tuning mode. See

“Clearing the preset FM or AM station” on page 13.

Once Presets Clear is performed, the deleted preset settings

cannot be restored.

1 Select “Presets Clear” in FM/AM function

menu.

2 Press B / C to select “OK” and then press E

or ENTER.

y

To cancel the operation, select “CANCEL”.

■ Auto Power Down

This unit automatically enters standby mode if it is not

operated for specified amount of time.

This setting is effective for all tuning modes. See “Auto

Power Down” on page 9 for detail.

TP Search function

(FM stations only)

Notes

TP

TP indicator lamp

Using the FM/AM functions

Note

FUNCTION

BAND

B / C / D / E /

ENTER

16 En

ADDITIONAL INFORMATION

Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below

or if the instruction below does not help, set this unit to the standby mode, disconnect the power cable, and contact the

nearest authorized Yamaha dealer or service center.

■ Tuner

TROUBLESHOOTING

Problem Cause Remedy

See

page

DAB

Cannot tune into any

DAB stations.

The automatic scanning operations

were not performed, or the DAB

registry list needs to be updated.

Perform the automatic scanning operations.

6

There is no DAB coverage in your

area.

Check with your dealer or WorldDMB online

at “http://www.worlddab.org” for a listing of

the DAB coverage in your area.

—

The DAB signals are too weak. Use a high-quality outdoor DAB antenna.

—

The automatic scanning

operations are not

successful.

The DAB antenna may not be

connected.

Make sure the DAB antenna is firmly

connected.

4

The DAB signals are too weak. Use a high-quality outdoor DAB antenna.

—

There is no DAB coverage in your

area.

Check with your dealer or WorldDMB online

at “http://www.worlddab.org/” for a listing of

the DAB coverage in your area.

—

The DAB station

reception is weak.

The positioning of the indoor DAB

antenna and/or this unit is not optimal

for DAB reception.

Use the tuning aid feature to locate the best

positioning of the DAB antenna and this unit

for optimal DAB reception.

9

The DAB signals are too weak. Use a high-quality outdoor DAB antenna.

—

There is noise

interference (e.g. hiss

or crackle).

The indoor DAB antenna needs to be

repositioned.

Readjust the position of the indoor DAB

antenna.

—

The DAB signals are too weak. Use a high-quality outdoor DAB antenna.

—

The DAB station

information does not

appear or is inaccurate.

The DAB station may be temporarily

out of service, or the DAB station

information is not provided by the

DAB broadcaster.

Contact the DAB broadcaster.

—

English

17 En

TROUBLESHOOTING

ADDITIONAL

INFORMATION

■ General

Problem Cause Remedy

See

page

FM

FM stereo reception is

noisy.

The characteristics of FM stereo

broadcasts may cause this problem

when the transmitter is too far away or

the antenna input is poor.

Check the antenna connections.

4

Try using a high-quality directional FM

antenna.

—

There is distortion, and

clear reception cannot

be obtained even with a

good FM antenna.

There is multi-path interference. Adjust the antenna position to eliminate

multi-path interference.

—

The desired station

cannot be tuned into

with the automatic

tuning method.

The signal is too weak. Use a high-quality directional FM antenna.

—

Use the manual tuning method.

11

The Radio Data System

information does not

appear.

The Radio Data System information is

not provided by the radio station.

The signal is too weak. Use a high-quality directional FM antenna.

—

AM

The desired station

cannot be tuned into

with the automatic

tuning method.

The signal is weak or the antenna

connections are loose.

Tighten the AM loop antenna connections

and orient it for the best reception.

—

Use the manual tuning method.

11

There are continuous

crackling and hissing

noises.

Noise can result from lightning,

fluorescent lamps, motors, thermostats

and other electrical equipment.

Use an outdoor antenna and a earth ground.

This will help somewhat, but it is difficult to

eliminate all noise.

—

There are buzzing and

whining noises.

A TV set is being used nearby. Move this unit away from the TV set.

—

Problem Cause Remedy

See

page

This unit fails to turn on when

A is pressed.

The power cable is not connected or

the plug is not completely inserted.

Connect the power cable firmly.

4

This unit has been exposed to a strong

external electric shock (such as

lightning or strong static electricity).

Disconnect the power cable, plug it back in

after 30 seconds, then use it normally.

—

A “humming” sound can be

heard.

Incorrect cable connections. Firmly connect the audio connection cord

plugs. If the problem persists, the cables may

be defective.

—

This unit does not operate

properly.

The internal microcomputer has been

frozen by an external electric shock

(such as lightning or excessive static

electricity) or by a power supply with

low voltage.

Disconnect the AC power plug from the

outlet and then plug it in again after about

30 seconds.

4

This unit suddenly turns off. The Auto Power Down function has

turned this unit off.

Change the auto power down setting.

9

18 En

DAB SECTION

• Output Level/Impedance ............................................. 1.5 V/1.2 kΩ

• Tuning Range

(Band III) ............................................................. 174 to 240 MHz

(L-Band) .......................................................... 1452 to 1492 MHz

• Sensitivity

(Band III) ........................................................................ –98 dBm

(L-Band) ......................................................................... –93 dBm

• Selectivity (for adjacent channel)

(Band III) .............................................................................. 40 dB

(L-Band) ............................................................................... 40 dB

• Signal to Noise Ratio .............................................................. 95 dB

• Total Harmonic Distortion ..................................................... 0.01%

• Stereo Separation (1 kHz) ....................................................... 77 dB

• Frequency Response .................. 20 Hz to 20 kHz, +0.5 dB/–1.0 dB

• Antenna Input (unbalanced) ..................................................... 75 Ω

FM SECTION

• Output Level/Impedance ............................................. 1.0 V/1.2 kΩ

• Tuning Range ................................................. 87.50 to 108.00 MHz

• 50 dB Quieting Sensitivity (IHF, 100% mod.)

Mono .................................................................... 3 µV (20.2 dBf)

• Usable Sensitivity (Signal to Noise Ratio, 30 dB, Mono) .... 1.0 µV

• Image Rejection Ratio ............................................................. 80 dB

• IF Rejection Ratio ................................................................... 70 dB

• Selectivity (400 kHz) .............................................................. 70 dB

• Signal to Noise Ratio (IHF)

Mono/Stereo .............................................................. 80 dB/75 dB

• Harmonic Distortion (1 kHz)

Mono/Stereo ................................................................ 0.3%/0.5%

• Stereo Separation (40 kHz Dev.)

1 kHz .................................................................................... 43 dB

• Frequency response (20 Hz to 15 kHz).................................... –3 dB

• Antenna Input (unbalanced) ..................................................... 75 Ω

AM SECTION

• Output Level/Impedance ........................................... 0.36 V/1.2 kΩ

• Tuning Range ........................................................ 531 to 1611 kHz

• Usable Sensitivity ............................................................. 300 µV/m

• Signal to Noise Ratio .............................................................. 50 dB

• Harmonic Distortion ................................................................. 1.0%

GENERAL

• Power Supply ........................................................ AC 230 V, 50 Hz

• Power Consumption ................................................................. 10 W

• Dimensions (W × H × D) ................................. 435 × 87 × 306 mm

(17 1/8 × 33/8 × 12 in)

• Weight ..................................................................................... 3.3 kg

(7.3 lbs)

* Specifications are subject to change without notice.

This receiver supports DAB/DAB+ tuning.

SPECIFICATIONS

Страница загружается...

Yamaha T-D500 Инструкция по применению

Похожие модели бренда

Модели других брендов