TRUSTMASTER T500 RS Инструкция по применению

User Manual (EUR)

User Manual (US)

Manuel de l’utilisateur (EUR)

Manuel de l’utilisateur (US)

Benutzerhandbuch

Gebruikershandleiding

Manuale d’uso

Manual del usuario (EUR)

Manual del usuario (US)

Manual do Utilizador

Инструкция по эксплуатации

Εγχειρίδιο χρήσης

Kullanım Kılavuzu

Click on your language below

1/20

For: PlayStation®3

User Manual

2/20

TECHNICAL FEATURES

1 Steering wheel base

2 Steering wheel

3 D-pad

4 2 digital gearshift levers (Up & Down)

5 Action buttons

6 LED

7 MODE button

8 Large screw thread (for the clamping

system and the clamp screw)

9 Clamping system

10 Metal clamp screw

11 Pedal set cable and connector

12 Steering wheel cable and USB connector

13 Mains adaptor

14 Mains adaptor power cable

3/20

11 Pedal set cable and connector

15 Removable foot rest

16 Arch

17 Removable pedal set

18 Removable “Realistic Brake” MOD

(not installed by default)

19 2mm Allen key, supplied

20 2.5mm Allen key, supplied

17 Metal head

21 Plastic Head Support

22 Pedal arm

23 Removable metal stop

(not installed by default)

4/20

WARNING

Before you use this product, please read this documentation carefully and keep it safe should you need to

consult it later.

* Store the product in a dry location and do not expose it to dust or sunlight.

Warning – Electric shock

* Respect the connection direction.

* Do not twist or pull the connectors and cables.

* Do not spill any liquid on the product or its connectors.

* Do not short-circuit the product.

* Never dismantle the product (except to adjust the pedal set if necessary); do not throw it onto a fire and

do not expose it to high temperatures.

* Do not use any adaptors other than the mains adaptor provided with the “T500 RS”.

* Do not use the mains adaptor if its connectors or cables are damaged, split or broken.

* Make sure that the mains adaptor’s power cable is perfectly inserted into the wall socket.

* If the steering wheel is operating unusually (if it is emitting any abnormal sounds, heat or odours), stop

using it immediately, disconnect the power cable from the socket and disconnect the other cables.

* If you are not going to be using the steering wheel for an extended period, disconnect the mains adaptor

from the wall socket.

Make sure that you do not block any of the air vents on the steering wheel base. For optimum ventilation,

respect the points below:

Air vents

* Position the base at least 10 cm away from any wall surfaces.

* Do not place the base in any tight spaces.

* Do not cover the base.

* Do not let any dust build up on the air vents.

5/20

Playing with a force-feedback steering wheel may cause muscle or joint pain. To avoid any problems:

Warning – Injuries due to force feedback and repeated movements

* Avoid lengthy gaming periods.

* Take 10 to 15 minute breaks after each hour of play.

* If you feel any fatigue or pain in your hands, wrists, arms, feet or legs, stop playing and rest for a few

hours before you start playing again.

* If the symptoms or pain indicated above persist when you start playing again, stop playing and

consult your doctor.

* Keep out of children’s reach.

* During games, always leave both hands correctly positioned on the steering wheel without letting it go

completely.

* During game calibration, never place your hand or arm inside the steering wheel.

* Check the steering wheel base is carefully clamped as per manual’s instructions.

* After each use, put the warning notice back in its original place on the wheel’s shaft, to warn any

potential new users.

To be handled only by users

16 years of age or older

HEAVY PRODUCT

Be careful not to drop the product on yourself

or on anyone else!

ALWAYS

NEVER

6/20

Warning – Pedal set pinch hazard when playing

* Keep the pedal set out of children’s reach.

* Do not remove the protections placed on the pedal arms.

* During games, never place your fingers near the

sides

* During games, never place your fingers near the

of the pedals.

rear base

* During games, never place your fingers near the

of the pedals.

front base

of the pedals.

NEVER

Warning – Pedal set pinch hazard when not playing

* Store the pedal set in a safe place, and keep it out of children’s reach.

* Do not remove the protections placed on the pedal arms.

7/20

INSTALLING THE WHEEL

Fixing the wheel to a Table or Desk

1. Place the wheel on a table or another flat surface.

2. Place the clamp screw (10) in the table clamp (9) then screw the clamping unit (anti-clockwise)

into the large screw thread (8) located under the wheel until it is perfectly stable.

ALWAYS NEVER

CAUTION: Never screw the clamp screw into the clamping system on its own!

(this may damage the steering wheel).

8/20

ASSEMBLY /

DISASSEMBLY

To tighten:

Screw

anti-

clockwise

To loosen:

Unscrew

clockwise

Attaching the steering wheel and pedal set to a cockpit

1. Place the steering wheel on the Cockpit’s tablet.

2. Tighten 2 “M6” screws (not supplied) into the Cockpit table and into the 2 small screw threads

under the wheel.

Important note for the Wheel

3. If necessary, screw in the standard clamping system (into the large screw thread).

: These screws must not be longer than 12mm to avoid damaging

the components inside the base.

4. In the same way, attach the Pedal set using the small screw threads underneath it.

Note for the Pedal set

Do not hesitate to test the different possible settings for more comfort.

: In certain cockpits the “Floor position” (F1 type) will be more user-friendly.

On others the “Suspended position (GT/Rally type)" will be more comfortable.

9/20

INSTALLATION ON PLAYSTATION®3

1. Connect the pedal set to the steering wheel by plugging in its connector (11) at the back of the

wheel.

2. Connect the mains adaptor to the wheel (13) by plugging in its connector to the back of the wheel.

3. Connect the mains adaptor to its power cable (14).

Note: To be sure that the 2 elements are perfectly connected, push the power cable’s connector into

the mains adaptor socket firmly.

4. Connect the mains cable (14) to a socket.

5. Connect the wheel’s USB connector (12) to the console’s No. 1 port.

You are now ready to play!

AUTOMATIC CALIBRATION FOR THE WHEEL AND PEDALS

The wheel calibrates itself automatically once the mains adaptor and the USB connector are connected.

This operation will cause the steering wheel to move quickly 1080° to the left and right before coming

to its final position in the center.

When calibrating the steering wheel

CAUTION:

never touch the wheel

(this may mislead the calibration or cause injury).

The pedals are also calibrated automatically once they have been pressed a few times.

TROUBLESHOOTING & TIPS

- My wheel and my pedals don’t work correctly or appear to be improperly calibrated:

Switch off your console, completely disconnect your wheel including all cables (with the mains

adaptor and the pedal set) and restart your game.

- There are various tips and help features (not included in this manual) available on the

website

http://ts.thrustmaster.com in the Technical Support category.

10/20

CONFIGURING THE PEDALS

Each of the 3 pedals features

- A “Metal Head (17)” with several perforations

:

(9 for the Accelerator – 6 for the Brake – 6 for the Clutch)

- A “Plastic Head Support (21)” (between the head and the arm) with 4 perforations

- A “Metal Arm (22)” with 4 perforations

CAUTION: To avoid any calibration problems, always disconnect the USB cable

from your steering wheel before adjusting the settings on your pedal set.

Adjusting the Pedal HEIGHT

- Using the 2.5mm Allen key supplied (20) loosen the 2 screws holding the “Metal Head (17) and its

support (21)”

- Once this is done, select the height you want and tighten the screws again.

Examples with the accelerator pedal:

Low position

Medium position (default)

High position

Very high position

- 4 for the Accelerator pedal

Number of height positions possible per pedal:

- 2 for the Brake pedal

- 2 for the Clutch pedal

11/20

Adjusting the Pedal SPACING

- Using the 2.5mm Allen key supplied (20) loosen the 2 screws holding the “Metal Head (17) and its

support (21)”

- Once you have done so, select your position (to the left, in the center or to the right) then tighten

the screws.

Examples with the brake pedal:

Left position Center position (default) Right position

- 3 for the Accelerator pedal

Number of spacing positions possible per pedal:

- 3 for the Brake pedal

- 3 for the Clutch pedal

Adjusting the Pedal TILT

- Using the 2.5mm Allen key supplied (20) loosen the 2 screws holding the “Metal Head (17) and its

support (21)”

- Once you have done so, turn the “Plastic Head Support (21)” over by 180° then tighten the screws.

Examples with the accelerator pedal:

Less tilted position More tilted position (default)

- 2 for the Accelerator pedal

Number of tilt positions possible per pedal:

- 2 for the Brake pedal

- 2 for the Clutch pedal

12/20

Adjusting the TRAVEL & resistance FORCE for the Brake pedal

To adjust the TRAVEL and resistance FORCE for the Brake pedal, you must remove the

transparent plastic pinch-hazard protector (protecting the brake pedal), and install the

included metal stop. By doing so, you will no longer benefit from the intended protection

against pinch hazards.

CAUTION:

To restore your protection against pinch hazards, you must remove the metal stop and

reinstall the transparent plastic pinch-hazard protector in its former location.

THRUSTMASTER® DISCLAIMS ALL RESPONSIBILITY FOR ANY INJURIES CAUSED BY

REMOVAL OF THE PINCH-HAZARD PROTECTOR OR INSTALLATION OF THE METAL STOP

- Unscrew the 2 screws holding the pinch-hazard protector on the brake pedal arm.

- Install the metal stop (23) at the rear of the brake pedal arm.

13/20

- Select your position (up, in the center or down) then tighten the screws using the 2.5mm Allen key

supplied (20).

Long run position Short run position

& High resistance (default) & Low resistance

Number of possible travel or resistance positions

- Long travel with resistance of around 10Kg (22lbs)

:

- Medium travel with resistance of around 8.5Kg (18.7lbs)

- Short travel with resistance of around 7Kg (15.4lbs)

Note

(and vice versa)

: the longer the travel the higher the pedal resistance

14/20

Installing the “Realistic Brake” MOD

To install the “Realistic Brake” MOD, you must remove the transparent plastic pinch-hazard

protector (protecting the brake pedal), and install the included metal stop. By doing so, you

will no longer benefit from the intended protection against pinch hazards.

CAUTION:

To restore your protection against pinch hazards, you must remove the metal stop and

reinstall the transparent plastic pinch-hazard protector in its former location.

THRUSTMASTER® DISCLAIMS ALL RESPONSIBILITY FOR ANY INJURIES CAUSED BY

REMOVAL OF THE PINCH-HAZARD PROTECTOR OR INSTALLATION OF THE METAL STOP

This MOD enables different sensations and resistance when braking.

Each user must decide whether or not to install it according to their preferences.

- Unscrew the 2 screws holding the pinch-hazard protector on the brake pedal arm.

15/20

- Install the MOD fully and tightly into the bottom of the “Metal Stop” cavity.

- For strong resistance: position the MOD against the Upper wall.

- For even stronger resistance: position the MOD against the Lower wall.

Position against the Upper wall

(Resistance of around 14Kg/30.8lbs)

Position against the Lower wall

(Resistance of around 16Kg/35.2lbs)

- Once you have done so, tighten the “Metal Stop” (23) at the rear of the pedal arm

Position against the Upper wall Position against the Lower wall

(Resistance of around 14Kg/30.8lbs) (Resistance of around 16Kg/35.2lbs)

To avoid any calibration problems, the “Realistic Brake” MOD must only be

installed in “Long Run” position

Important note:

(do not install it in “Medium Run” or “Short Run” position)

16/20

TURNING THE PEDAL SET POSITION OVER

The “T500 RS” pedal set has a unique design (patent pending) that allows for a choice of 2

positions:

- Floor position (F1 type)

- Suspended position (GT/Rally type)

By default, the pedal set is delivered in “Floor” position (F1 type)

Floor position (F1 type) Suspended position (GT/Rally type)

17/20

REVERSING THE PEDAL SET PHYSICALLY

- Using the 2mm Allen key (19) loosen the 4 screws holding the “Removable Foot Rest (15)”

- Turn the pedal set over 90° then tighten the "Foot Rest" again on the 4 screw threads located on

the "Arch (16)”

18/20

- Using the 2.5mm Allen key (20) loosen the 3 "Metal Heads (17)” to turn them over 180° and

reverse the Accelerator head and the Clutch head.

You are now ready to play!

ELECTRONIC REVERSAL for the accelerator & clutch pedals

When you turn over the pedal set position: simply press the MODE button (7) to reverse the

accelerator and clutch pedals electronically

(the LED colour tells you the position you have chosen)

PEDAL SET POSITION

LED (6)

colour

ON THE FLOOR (F1 type)

(installed by default)

RED

SUSPENDED (GT/Rally type) GREEN

Once you have done this the selected position is stored immediately

in the wheel’s internal memory

19/20

TECHNICAL SUPPORT

If you encounter a problem with your product, please go to http://ts.thrustmaster.com and click Technical Support.

From there you will be able to access various utilities (Frequently Asked Questions (FAQ), the latest versions of drivers

and software) that may help to resolve your problem. If the problem persists, you can contact the Thrustmaster

products technical support service (“Technical Support”):

By email:

In order to take advantage of technical support by email, you must first register online. The information you provide will

help the agents to resolve your problem more quickly. Click Registration on the left-hand side of the Technical Support

page and follow the on-screen instructions. If you have already registered, fill in the Username and Password fields

and then click Login.

By telephone:

United

Kingdom

08450800942

Charged

at local rate

Monday to Saturday from 8 a.m. to 7 p.m.

Denmark

80887690

Free

Monday to Saturday from 9 a.m. to 8 p.m.

(English)

Sweden

0200884567

Free

Monday to Saturday from 9 a.m. to 8 p.m.

(English)

Finland

0800 913060

Free

Monday to Saturday from 10 a.m. to 9 p.m.

(English)

Hours of operation and telephone numbers are subject to change. Please visit http://ts.thrustmaster.com for the most

up-to-date Technical Support contact information.

WARRANTY INFORMATION

Worldwide, Guillemot Corporation S.A. (“Guillemot”) warrants to the consumer that this Thrustmaster product will be

free from material defects and manufacturing flaws for a period of two (2) years from the original date of purchase.

Should the product appear to be defective during the warranty period, immediately contact Technical Support, who will

indicate the procedure to follow. If the defect is confirmed, the product must be returned to its place of purchase (or any

other location indicated by Technical Support).

Within the context of this warranty, the consumer’s defective product will, at Technical Support’s option, be either

repaired or replaced. Where authorized by applicable law, the full liability of Guillemot and its subsidiaries (including for

indirect damages) is limited to the repair or replacement of the Thrustmaster product. The consumer’s legal rights with

respect to legislation applicable to the sale of consumer goods are not affected by this warranty.

This warranty shall not apply: (1) if the product has been modified, opened, altered, or has suffered damage as a result

of inappropriate or abusive use, negligence, an accident, normal wear, or any other cause not related to a material

defect or manufacturing flaw; (2) in the event of failure to comply with the instructions provided by Technical Support;

(3) to software not published by Guillemot, said software being subject to a specific warranty provided by its publisher.

Страница загружается ...

TRUSTMASTER T500 RS Инструкция по применению

TRUSTMASTER T500 RS Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов