Thrustmaster FERRARI WIRELESS F430 COCKPIT Инструкция по применению

1/20

Compatible with: PlayStation® 3 & PC

User Manual

TECHNICAL FEATURES

1 2 rear clamp screws

(to set the steering column angle)

2 Transport handle

3 Adjustable column of the base

4 Removable wheel

5 Power cord

6 1 front clamp screw

(for setting the length)

7 Brake and accelerator pedals

8 Battery and receiver

storage compartment

9 Up & Down gearshift paddles

10 Manettino with 5-position rotary switch

(for programming)

11 “Select” and “Start” buttons

12 Multidirectional D-Pad

13 Action buttons

14 Wireless receiver

15 USB connector of the receiver

16 Receiver LED

17 PC/PS3 switch of the receiver

2/20

INSTALLING THE WHEEL

ADJUSTING THE TILT AND LENGTH

OF THE DRIVING POSITION

- Slightly unscrew (anticlockwise) the 2 clamp screws (1) at the back of the base.

- Adjust the angle of the base’s column (3) so that is suitable to you.

- Then tighten (clockwise) the 2 clamp screws (1).

3/20

- Slightly unscrew (anticlockwise) the clamp screw (6) located at the front of the base’s column. Then draw

out the column to the length you require.

- Then tighten (clockwise) the clamp screw (6), taking care that it is correctly inserted into one of the holes

provided for this purpose. You can do this simply by positioning the upper hole by the locating mark

provided for this purpose.

4/20

FITTING THE WHEEL TO THE BASE

Lugs (front of the base) Lug notches (back of the wheel)

+

Locking tab (back of the wheel)

- Position the removable wheel (4) horizontally, and then insert the 2 lugs (on the front of the base) into

the 2 lug notches (on the back of the wheel).

- Let the wheel down vertically, and then lock the wheel into position by pressing the locking tab (on the

back of the wheel) then releasing it until you hear a gentle “click”.

- Check that the steering wheel is correctly secured to the base.

5/20

- Electronically connect the steering wheel to its base by connecting the elbow-shaped male connector (on

the end of the power cord (5)) to the female connector (to the left of the wheel).

- Rotate the nut (on the end of the connector) clockwise to secure the connection.

PERFORM THE OPERATION IN REVERSE TO

TAKE OFF THE REMOVABLE WHEEL FROM THE BASE

6/20

FITTING BATTERIES AND RECOVERING THE RECEIVER

- Remove cover from the battery compartment (8) (located between the 2 pedals) and fit 4 LR6 / AA

batteries, ensuring that the polarities are in the right position.

- Recover the wireless receiver (14) found in the lower section of the battery compartment.

- Fit back the battery compartment’s cover.

7/20

SWITCHING THE WHEEL ON OR OFF

- Position the switch (located on the right-hand side of the wheel):

- To ON for switching on the wheel.

- To OFF for switching off the wheel.

Important note:

When you switch on your wheel, it must always be perfectly centred physically (to prevent any

misalignment).

8/20

PLAYSTATION® 3

INSTALLATION ON PLAYSTATION® 3

1. Set the PC/PS3 switch (17) of the receiver (14) to the “PS3” position.

2. Connect the USB connector (15) of the receiver to the USB port 1 of the console.

3. Turn on your console.

4. Turn on your wheel by using the ON/OFF switch.

5. When the connection is set up, launch the game.

You are now ready to play!

USING THE “PS” BUTTON

The “PS” button of your wheel allows you to exit your games, access the menus and directly switch off your

PlayStation® 3 system.

Procedure:

Set the Manettino (10) switch to the relevant icon, and then press the push button.

Important notes on PlayStation® 3:

- The PC/PS3 switch (17) of the receiver must always be set to “PS3” before connecting it.

- In “1-player” mode: If your official gamepad is turned on, you will have to switch it to “controller port 2”

in order for your wheel to be functional.

- On PlayStation® 3, the wheel simulates the official gamepad (which makes it compatible with all

racing games).

- In most games, the “Normal Sensitivity” mode (just as on the gamepad) has a slight dead zone

that can be felt in the middle of the wheel axis (and therefore the centre of the wheel).

The wheel’s “High Sensitivity” mode is set to remove this dead zone.

However, some games allow you to remove or reduce this dead zone by changing the settings

of the steering wheel axis in the game’s “Options/Commands”.

“High Sensitivity” mode is recommended for most PS3 games (where it is not possible to

change the central dead zone of the steering wheel axis).

“Normal Sensitivity” mode is recommended only for PS3 games where the central dead zone of

the steering wheel axis can be changed.

9/20

CONFIGURING THE “AUTOMATIC PRESET” - PLAYSTATION® 3

(in “Separate pedal set” mode)

10/20

PC

INSTALLATION ON PC

Required configuration: PC (Windows® Xp, Windows® Vista, Windows® 7) equipped with a USB port

The CD-ROM included with this product allows you to install the drivers.

1. Insert the installation CD-ROM into your CD-ROM drive. The install wizard is displayed automatically (if the

installation menu does not run automatically, double-click “Workstation”, then the icon of the CD-ROM and,

“Setup.exe” if necessary).

2. Click on the “DRIVERS” to start installing the drivers.

3. Once the installation is complete, click Finish and restart your computer.

4. Set the PC/PS3 switch (17) of the receiver (14) to the “PC” position.

5. Once your computer has restarted, connect the USB connector (15) of the receiver to one of the USB ports

of your central unit. Windows® will automatically detect the new device.

6. Drivers are installed automatically.

Follow the on-screen instructions to complete the installation.

7. Select Start/Programs/Thrustmaster/Control Panel to access the Control Panel.

The Game controllers dialogue box will display the name of the wheel with the OK status.

8. In the Control Panel, click Properties to test and view the buttons, D-pad and axes of the wheel and

the pedal set.

You are now ready to play!

Important notes on PC:

- The PC/PS3 (17) switch of the receiver must always be set to “PC” before connecting the wheel.

- The wheel name declared on PC (in the Control Panel and in the games) is “F430 Cockpit Wireless”.

11/20

CONFIGURING THE “AUTOMATIC PRESET” - PC

(in “Separate pedal set” mode)

12/20

USING THE 5-POSITION MANETTINO

The Manettino (10) system comprises:

- a rotary switch that you can turn to go from one function to another

- a push button located under the switch (to confirm your choices)

The required function will start as soon as you press the push button (not when you turn the switch) with the

switch positioned opposite the relevant icon.

Manettino Button functions and correspondence with the LEDs

“PS” on PS3 button and “13” on PC

- On = connection set up between the wheel and the receiver.

- Flashes quickly = no connection between the wheel and the receiver.

- Flashes slowly and continuously = you must change the batteries.

- Off = the wheel is in standby mode or off.

“Normal Sensitivity” mode

- On = “Normal Sensitivity” with “Separate pedal set” modes enabled

- Flashes quickly = mode “Combined pedal set” enabled

“High Sensitivity” mode

- On = “High Sensitivity” with “Separate pedal set” modes enabled

- Flashes quickly = “Combined pedal set” mode enabled

“Mapping”

- On = “Mapping” mode enabled (pending programming)

“Manual Preset”

- On = “Manual Preset” mode enabled

- Set the Manettino switch to the relevant icon.

- Press the push button to confirm the function.

13/20

GENERAL

WHEEL POWER BUTTON

- OFF position = the wheel is off (and does not use the batteries).

- ON position = the wheel is on.

The wheel and receiver are automatically connected.

If the connection fails, you can force the connection by pressing the LED button of the receiver (16), then

the SELECT + START +

buttons simultaneously on the wheel.

STANDBY MODE

The wheel automatically switches off:

- After 5 minutes of inactivity.

- After 5 seconds if the connection fails or is lost.

The wheel can be activated by pressing one of its action buttons (13)

or operating the wheel’s ON/OFF switch.

“PC / PS3” SWITCH (17) OF THE RECEIVER

This switch must always be set to the correct position before you connect your receiver to the USB port of

your PlayStation® 3 or PC.

LED AND RECEIVER LED (16)

- Both LEDs are on = connection set up between the wheel and the receiver.

- Both LEDs flash quickly = no connection between the wheel and the receiver.

-All the LEDs on the Manettino are off = the wheel is in standby mode or off.

- The

LED flashes slowly and continuously = you must change the batteries.

AUTOMATIC CALIBRATION OF THE WHEEL AND PEDALS

- The centre of the wheel is preset as soon as you turn it on: it is therefore vital for the wheel to be perfectly

aligned on its axis when you switch it on.

- Nevertheless, you can manually adjust the centre of the wheel. To do this, position the wheel in perfect

alignment with the centre, and then simultaneously press “SELECT + START + ENGINE START” (this

operation must be carried out each time the wheel is switched on).

- The steering of the wheel and the pedals automatically self-calibrate.

14/20

ADVANCED FUNCTIONS

ADJUSTING THE WHEEL’S SENSITIVITY

Your wheel’s steering has 2 sensitivity modes:

- “Normal Sensitivity” (default mode and recommended on PC - requires setting on PS3)

- “High Sensitivity” (default mode and recommended on PS3 - requires setting on PC)

Setting “Normal Sensitivity” mode (default mode and recommended on PC)

Action

- Set the Manettino switch to the relevant icon.

- Press the push button to confirm the function.

ON

Your wheel’s steering is now at Normal Sensitivity

Setting “High Sensitivity” mode (default mode and recommended on PS3)

Action

- Set the Manettino switch to the relevant icon.

- Press the push button to confirm the function.

ON

Your wheel’s steering is now more sensitive, especially at the centre

CONFIGURING THE PEDALS

Your wheel’s accelerator and brake controls are in “separate” mode by default, meaning that the pedals

function on independent axes.

This mode lets you considerably improve the precision of your steering.

If you game does not support the “separate” mode, the pedal set of the wheel will not work correctly. You

must therefore activate the “Combined” mode.

SETTING

Simultaneously press and release both pedals (accelerator and brake) + the

button.

PEDAL SET MODE

or

SEPARATE

(recommended mode for most games)

DOES NOT FLASH

COMBINED FLASHES

15/20

CONFIGURING THE PEDALS ON PLAYSTATION® 3

CONFIGURING THE PEDALS ON PC

Separate pedal set (default mode) Combined pedal set (must be set)

- Accelerator = RZ axis

- Brake = Y axis

- Accelerator = Up direction of the Y axis

- Brake = Down direction of the Y axis

Separate pedal set (default mode) Combined pedal set (must be set)

- Accelerator = R2 trigger

of the PS3 gamepad

- Brake = L2 trigger

of the PS3 gamepad

- Accelerator = Up direction

of the “right mini-stick” of the PS3 gamepad

- Brake = Down direction

of the “right mini-stick” of the PS3 gamepad

16/20

PROGRAMMING THE WHEEL AND PEDALS

Your wheel is fully programmable:

- All the action buttons can be switched between themselves.

- All the action buttons can be programmed onto the pedals or gearshift paddles.

TWO PROGRAMMING MODES

The button and the PRESET LED allow you to view the programming type chosen:

AUTOMATIC (pre-programmed) or MANUAL (programmed by yourself). Simply pressing this button allows you

to switch from one programming mode to another (even during a game).

“AUTOMATIC PRESET” (PRESET

BUTTON OFF)

This is the default programming.

For more information, refer to the diagrams in CONFIGURING “AUTOMATIC PRESET”

- PLAYSTATION® 3 / PC.

“MANUAL PRESET” (PRESET

BUTTON ON)

This is your personal programming. The buttons can either be:

- programmed onto the pedals or gearshift paddles

- or switched between each other.

- You can change your programming whenever you want.

- The programming is automatically saved in the wheel (even when it is disconnected or switched off).

- When your “MANUAL PRESET” is blank, it is identical to “AUTOMATIC PRESET”.

PROGRAMMING PROCEDURE

Steps Action LED status

1

Activate “MANUAL PRESET”

by pressing the button.

On

2

Press and release the MAPPING button

On

3 Press and release the button to programme.

Flashing

4

Press and release the button, the gearshift paddle or pedal you

want to assign to this function.

Off

On

Your “MANUAL PRESET” programming is now enabled and updated (with your programming applied).

17/20

EXAMPLES OF POSSIBLE USES:

- On PS3, programme L2/R2 or L3/R3 onto the Up and Down gearshift paddles (L1/R1 by default).

- On PS3, programme the Cross/Square buttons onto the pedals (L2/R2 by default).

- Switch different buttons for better access.

Note: The button cannot be programmed or moved.

EEPROM MEMORY

Your wheel has an internal chip that stores all your “MANUAL PRESET” programmes in memory (even

when the wheel is off or disconnected for a long period of time).

You can save a different “MANUAL PRESET” on each support used (PC and PS3).

DELETING A “MANUAL PRESET”

Steps Action LED status

1

Activate your “MANUAL PRESET”

On

2

Press and hold the MAPPING

button for 2 seconds.

Flashes for 2 seconds

Your “MANUAL PRESET” is now blank (and becomes identical to the “AUTOMATIC PRESET”).

RETURN TO “FACTORY SETTINGS”

The aim here is to remove all of your programming or settings in one go.

Steps Action LED status

1

Simultaneously press the following buttons

MAPPING

+ SELECT + START

Flashes for 5 seconds

All your “MANUAL PRESETS” (PC + PS3) or settings are now blank.

Note: The result of this action is to fully restart your wheel. On a PC, you should

therefore carry out this operation only when no game is currently playing.

18/20

TROUBLESHOOTING

The wheel is not perfectly centred in the games:

- Switch off the wheel (by setting the switch to OFF). Physically centre the wheel. Next, switch the wheel

back on (by setting the switch to ON).

- If the problem persists, you can manually centre the wheel. To do this, position the wheel in perfect

alignment with the centre, and then simultaneously press “SELECT + START + ENGINE START” (this

operation must be carried out each time the wheel is switched on).

- On the PC, if the wheel or pedals are not properly calibrated, download the “Thrustmaster Calibration

Tool v 1.03” manual calibration software available at the following address: http://ts.thrustmaster.com

.

My wheel or pedals do not work correctly:

- Switch the wheel off and back on again (making sure the wheel is centred on start-up).

- Check the condition of the 4 LR6 / AA batteries and that their polarities are correctly positioned.

- If the problem persists, switch off your computer or your console, disconnect the USB receiver as well as

the power cord, reconnect all of them again, then restart and launch your game again.

On PC, my wheel is detected but does not work with my game:

Open the interface for managing your game’s “Options” to configure your wheel. Refer to your game’s

user manual or online help for more information.

On PS3, my wheel is not detected:

- In “1 player” mode: If your official gamepad is turned on, you will have to switch it to “controller port 2” (using

the “PS” button) for your wheel to be functional.

- If the problem persists, switch off your gamepad while leaving only the wheel connected.

My pedals do not work correctly in “Separate Mode”:

(E.g. when the game is running, the selection cursor moves all by itself)

Exit the game and switch the pedals to “combined” mode. Then return to your game to reconfigure the

wheel in your game’s option management interface.

My wheel cannot connect itself to the receiver:

The connection between the wheel and the receiver is made automatically.

In the event of a connection failure, you can force the connection by pressing the LED button of the

receiver (16), then simultaneously on your wheel’s SELECT + START +

buttons.

The

LED flashes continuously:

You must change the batteries.

SAFETY RECOMMENDATIONS AND INFORMATION

During extended periods of non-use, switch off the wheel (by setting the switch to OFF),

remove the wheel from its base and remove the 4 batteries from the battery compartment.

19/20

TECHNICAL SUPPORT

If you encounter a problem with your product, please go to http://ts.thrustmaster.com and click Technical

Support. From there you will be able to access various utilities (Frequently Asked Questions (FAQ), the

latest versions of drivers and software) that may help to resolve your problem. If the problem persists, you

can contact the Thrustmaster products technical support service (“Technical Support”):

By email

:

In order to take advantage of technical support by email, you must first register online. The information you

provide will help the agents to resolve your problem more quickly. Click Registration on the left-hand side

of the Technical Support page and follow the on-screen instructions. If you have already registered, fill in

the Username and Password fields and then click Login.

By telephone

:

United Kingdom

08450800942

Charges

at local rate

Monday to Friday from Noon to 4pm and 5pm to 10pm

Saturday from 9am to Noon and 1pm to 7pm

Sunday from 9am to Noon and 1pm to 4pm

United States

1-866-889-5036

Free

Monday to Friday from 7am to 11am and from Noon to

5pm

Saturday and Sunday from 7am to Noon

(Eastern Standard Time)

Canada

1-866-889-2181

Gratuit / Free

Monday to Friday from 7am to 11am and from Noon to

5pm

Saturday and Sunday from 7am to Noon

(Eastern Standard Time)

Denmark

80887690

Free

Monday to Friday from 1pm to 5pm and 6pm to 11pm

(English)

Saturday from 9am to 1pm and 2pm to 8pm

Sunday from 10am to 1pm and 2pm to 5pm

Sweden

0200884567

Free

Monday to Friday from 1pm to 5pm and 6pm to 11pm

(English)

Saturday from 9am to 1pm and 2pm to 8pm

Sunday from 10am to 1pm and 2pm to 5pm

Finland

0800 913060

Free

Monday to Friday from 2pm to 6pm and 7pm to Midnight

(English)

Saturday from 10am to 2pm and 3pm to 9pm

Sunday from 11am to 2pm and 3pm to 6pm

WARRANTY INFORMATION

Worldwide, Guillemot Corporation S.A. (“Guillemot”) warrants to the consumer that this Thrustmaster product will

be free from material defects and manufacturing flaws for a period of two (2) years from the original date of

purchase. Should the product appear to be defective during the warranty period, immediately contact Technical

Support, who will indicate the procedure to follow. If the defect is confirmed, the product must be returned to its

place of purchase (or any other location indicated by Technical Support).

Within the context of this warranty, the consumer’s defective product will, at Technical Support’s option, be either

repaired or replaced. Where authorized by applicable law, the full liability of Guillemot and its subsidiaries

(including for indirect damages) is limited to the repair or replacement of the Thrustmaster product. The consumer’s

legal rights with respect to legislation applicable to the sale of consumer goods are not affected by this warranty.

Страница загружается...

Thrustmaster FERRARI WIRELESS F430 COCKPIT Инструкция по применению

Похожие модели бренда

Модели других брендов