YAMAHA ELECTRONICS CORPORATION, USA
6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.
135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.
SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.
RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.
YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY. LTD.
LEVEL 1, 99 QUEENSBRIDGE STREET, SOUTHBANK, VIC 3006, AUSTRALIA
©
2008 All rights reserved.
F
OWNER’S MANUAL
DVX-1000
(DVR-1000 + NX-SW1000 + NX-P1000)
Printed in China 3139 245 28722
DVX-1000
En
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place with at least 10 cm on the top, 10 cm on the left and
right, and 10 cm at the back of DVR-1000 and at least 1 m
above, 30 cm behind and on both sides of NX-SW1000 for
adequate ventilation. — away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, nor locate this unit in an environment with high
humidity (i.e., a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit in a location where foreign objects
may fall onto this unit or where this unit may be exposed to
liquid dripping or splashing. On the top of this unit, do not
place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e., candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall, spilling
the liquid and causing an electrical shock to the user and/
or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use excessive force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall outlet,
grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using this unit
with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any damage resulting
from use of this unit with a voltage other than as specified.
13 To prevent damage by lightning, keep the power cord out and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reason.
15
When not planning to use this unit for long periods of time (i.e.,
vacation), disconnect the AC power plug from the wall outlet.
16 Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set the unit
in standby mode, then disconnect the AC power plug from the
wall outlet.
18 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the
outlet, then leave the unit alone.
19 When using the unit for a long time, the unit may become
warm. Turn the power off, then leave the unit alone for
cooling.
20 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such as
sunshine, fire or like.
22 Excessive sound pressure from earphones and headphones
can cause hearing loss.
Caution: read this before operating your unit.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
Laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
This symbol mark is according to the
EU directive 2002/96/EC.
This symbol mark means that electrical
and electronic equipment, at their end-
of-life, should be disposed of separately
from your household waste.
Please act according to your local rules
and do not dispose of your old products
with your normal household waste.
This product complies with the radio interference
requirements of the European Community.
This product complies with the
requirements of the following directives
and guidelines: 2006/95/EC + 2004/
108/EC
1 En
1
2
3
4
5
6
7
English
Introduction................................................ 2
Main unit......................................................... 4
Supplied accessories........................................ 4
Functional overview .................................. 5
Top and front panels (DVR-1000) .................. 5
Rear panel (DVR-1000).................................. 6
Rear panel (NX-SW1000)............................... 7
Remote control
(For DVR-1000).......................................... 8
Connections ............................................. 10
Roles and layout of the speakers................... 10
System connections................................ 11
Connecting the speakers................................ 11
Other connections ................................... 14
Connecting a TV ........................................... 14
Connecting an HDMI component................. 15
Connecting the FM/AM antennas................. 17
Connecting external AV components ........... 18
Connecting a digital audio component.......... 19
Connecting a USB device ............................. 19
Getting started ......................................... 20
Inserting batteries into the remote control .... 20
Using the remote control............................... 20
Setting a TV .................................................. 21
Setting language preferences......................... 23
Setting speaker channels ............................... 24
Disc operation .......................................... 25
Playing discs.................................................. 25
Basic playback controls................................. 25
Selecting various repeat shuffle functions .... 26
Other operations for video playback
(DVD/VCD/SVCD) .................................. 27
Playing MP3/WMA/JPEG/DivX® discs ...... 29
Special features for picture disc playback..... 30
Using a USB device ...................................... 31
DVD setup menu options........................ 33
Menu overview.............................................. 33
General setup menu ....................................... 34
Audio setup menu.......................................... 36
Video setup menu.......................................... 37
Preference setup menu................................... 41
Tuner operations..................................... 44
Tuning radio stations ..................................... 44
Presetting radio stations................................. 44
Receiving Radio Data System stations (Europe
and Russia models only)............................ 45
Sound controls........................................ 47
Using the Virtual Surround function ............. 47
Setting music enhancer.................................. 47
Night listening mode ..................................... 48
Adjusting the treble/bass level....................... 48
Adjusting the volume level............................ 48
Other functions........................................ 49
Switching to standby mode ........................... 49
Dimming the display screen .......................... 49
Setting the sleep timer ................................... 49
Recording on an external AV component ..... 49
Troubleshooting...................................... 50
Glossary................................................... 53
Specifications.......................................... 55
Index......................................................... 56
(at the end of this manual)
LIST OF LANGUAGE CODES ...................... i
LASER INFORMATION ............................... ii
Contents
1. INTRODUCTION
2. PREPARATION
3. BASIC OPERATION
4. OPERATIONS
5. ON-SCREEN MENU
6. OTHER FEATURES
7. ADDITIONAL INFORMATION
APPENDIX
2 En
INTRODUCTION
Thank you for purchasing this unit. This Owner’s Manual
explains the basic operation of this unit.
Notes about discs
– This receiver is designed for use with the following
discs: DVD-Video, Video CD, Super Video CD,
Audio CD, CD-R, CD-RW, DVD+RW, DVD+R,
DVD-R, DVD-RW and DVD-RW (VR format).
This receiver can play:
– MP3 and picture (Kodak, JPEG) files recorded on
CD-R/RW, DVD-R/RW and DVD+R/RW.
– JPEG/ISO 9660 format
– Maximum 30 character display
–DivX
®
disc on CD-R[W]/DVD+R[W]/
DVD-R[W](3.11, 4.x and 5.x)
– CD-R, CD-RW and DVD-RW (VR format) cannot
be played unless finalized.
– Some discs cannot be played depending on the
recording conditions, such as the PC environment
and application software. The characteristics and
condition of some discs; materials, scratches,
curvature, etc. may result in playback failure.
– Be sure to use only CD-R/RW, DVD-R/RW and
DVD+R/RW discs made by reliable manufacturers.
– Do not use any non-standard shaped discs (heart-
shaped, etc.).
– Do not use discs with tape, seals, or paste on their
surface. Doing so may damage this receiver.
– Do not use discs affixed with labels printed by a
commercially available label printer.
Cleaning discs
– When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not
wipe in a circular motion.
– Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic spray
intended for analog records.
Avoid high temperatures, moisture, water
and dust
– Do not expose the system, batteries or discs to
humidity, rain, sand or excessive heat (caused by
heating equipment or direct sunlight).
Avoid condensation problem
– The lens may cloud over when the receiver is
suddenly moved from cold to warm surroundings,
making it impossible to play a disc. Leave the
receiver in the warm environment until the moisture
evaporates.
Disc care
– Write only on the printed side of a CD-R[W]/
DVD+R[W]/DVD-R[W] and only with a soft felt-
tipped pen.
– Handle the disc by its edge; do not touch the
surface.
Cabinet care
– Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution containing
alcohol, spirits, ammonia, or abrasives.
Choosing a suitable location
– Place the receiver on a flat, hard, and stable surface.
Introduction
Notes
3 En
Introduction
English
INTRODUCTION
1
Region codes
The unit is designed to support the Region Management
System. Check the region code number on the disc
package. If the number does not match the unit’s region
number (see the table below or the back of the unit), the
unit may be unable to play the disc.
Sound field features
Destination
Region
code of
DVR-1000
Playable
discs
Europe
model
Australia
model
Korea, Asia and
Taiwan models
Russia
model
2 2
ALL
4 4
ALL
3 3
ALL
5 5
ALL
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic”, “MLP
Lossless” and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Surround” are
registered trademarks of DTS, Inc.
DivX, DivX Ultra Certified, and associated
logos are trademarks of DivX, Inc. and are used
under license.
“DCDi” is a trademark of Faroudja, a division
of Genesis Microchip, Inc.
HDMI, the HDMI logo and High Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Active Servo Processing Subwoofer System with built-in
power amplifier.
This subwoofer system (NX-SW1000) employes Advanced
Yamaha Active Servo Technology which Yamaha has
developed for reproducing higher quality super-bass sound.
This super-bass sound adds a more realistic, theater-in-the-
home effect to your stereo system.
4 En
Introduction
■ Main unit ■ Supplied accessories
DVD receiver
(DVR-1000)
Subwoofer
(NX-SW1000)
Be sure to connect the power cable of the
subwoofer (NX-SW1000) to the AC outlet
before you turn on the DVD receiver (DVR-
1000). Otherwise, the subwoofer (NX-SW1000)
will not be powered correctly.
Note
Front speakers (x2)
(NX-P1000)
STANDBY/ON
EJECT
DIMMER
BASS TREBLE
ENTER
DIRECT
DVD/CD
TUNER
SURROUND
AUX
SUBTITLE
ANGLE ZOOM AUDIO
MUTE
AREA
MODE
USB
ENHANCER
NIGHT
REPEAT
ON SCREEN
MENU
SET UP
TOP MENU
/RETURN
FREQ/TEXT
MODE START
PRESET PRESET
PROG
A-B
SHUFFLE
SLEEP
PTY SEEK
Power cable
(For NX-SW1000: except
Europe and Russia models)
Power cable
(For DVR-1000)
Remote control
Batteries (x 2)
System control cable (4 m)
(For NX-SW1000)
Speaker cables (4 m x 2)
(For NX-P1000)
Video pin cable (1.4 m)
Indoor FM antenna
AM loop antenna
(Asia, Australia, Korea,
and Taiwan models only)
5 En
English
INTRODUCTION
1
■ Top and front panels (DVR-1000)
1 System display panel
Shows information about the operational status of the
unit.
2 PCM/ Digital/DTS indicator
Indicates the format of the audio being played back.
3 d VOLUME u
Adjusts the volume level.
4 INPUT
Selects input source or sets the priority level for the
audio input signals.
5 b/w, f/a
DVD/CD mode: selects the previous/next track or
chapter. Press and hold to fast forward or fast reverse.
TUNER mode: tunes the radio preset up/down.
USB mode: selects the previous/next track. Press and
hold to fast forward or fast reverse.
6 s
Exits an operation.
DVD/CD mode: stops disc playback.
TUNER mode: erases a preset radio station in Preset
mode if held more than two seconds, or stops preset
radio station installation in Auto Preset mode.
USB mode: stops playback.
7 e
DVD/CD mode: pauses disc playback.
USB mode: pauses playback.
8 h
DVD/CD mode: starts disc playback.
USB mode: starts playback.
9
Ejects a disc in the DVD receiver.
Do not push the ejected disc when reloading it. To
reload the ejected disc, press or h, or remove the
disc from the disc loading slot fully, then insert it to
the disc loading slot once again.
0 USB terminal
Connect to the USB connector of your USB device
(see page 19).
A STANDBY/ON
Turns on the DVD receiver, or sets it to the standby
mode (see “Turning the auto standby function on/off”
on page 35).
B Disc loading slot
Insert a disc to be played.
C Remote control sensor
Point the remote control towards this sensor.
D PHONES jack
Connects headphones.
E PORTABLE jack
Connects a portable audio player.
When this input source is selected, “FRONT IN”
appears on the system display panel.
Functional overview
7 8 965432
E
C
D
B
A
0
1
Note
6 En
Functional overview
■ Rear panel (DVR-1000)
(Europe model)
1 AC inlet
Connect the supplied power cable.
2 COMPONENT VIDEO OUT jacks
Connect to the Y P
B/CB PR/CR jacks on your TV (see
page 14).
3 VIDEO output jack
Connect to the video (composite) jack on your TV
(see page 14).
4 FM ANT terminal
Connect the FM antenna.
5 GND and AM ANT terminals
Connect the AM loop antenna.
6 SYSTEM CONNECTOR terminal
Connect the subwoofer.
7 OPTICAL DIGITAL IN jack
Connect to the DIGITAL OUT jack on your digital
audio component.
8 AUX IN jacks
Connect to the AUDIO OUT jacks on your VCR or
cassette deck.
9 LINE OUT jacks
Connect to the AUDIO IN jacks on your VCR.
0 S VIDEO output jack
Connect to the S-video jack on your TV or VCR.
A AV MONITOR OUT terminal
(Europe and Russia models only)
Connect to your TV (see page 14).
B HDMI terminal
Connect to the HDMI input terminal of your HDMI
component (see page 15).
SYSTEM
CONNECTOR
MAINS
TO SUBWOOFER
AUX I N
AUDI O
LINE OUT
AV MONITOR OUT
(
DVD ON LY
)
S VIDEO
VIDEO
COMPONENT
Y
P
R
PB
PCM/DTS
q
DIGITAL
OPTICAL
DIGITAL IN
VIDEO OUT
(DVD ONLY)
AM
ANT
GND
TUNER
HDMI
FM
ANT
75Ω UNBAL
L
R
L
R
98
21 4 5
67
3
B
0 A
7 En
Functional overview
English
INTRODUCTION
1
■ Rear panel (NX-SW1000)
1 SYSTEM CONNECTOR terminal
Connect to the DVD receiver.
2 SPEAKER terminals
Connect to the speakers.
3 AC power cord
Connect to a standard AC outlet.
1 SYSTEM CONNECTOR terminal
Connect to the DVD receiver.
2 SPEAKER terminals
Connect to the speakers.
3 VOLTAGE SELECTOR
Select the voltage according to your region.
4 AC inlet
Connect the supplied power cable.
SYSTEM
CONNECTOR
6
Ω
MIN. /SPEAKER
SPEAKERS
MAINS
L
R
1
3
2
SYSTEM
CONNECTOR
6
Ω
MIN. /SPEAKER
SPEAKERS
AC IN
VOLTAGE
SELECTOR
L
R
110V-120V
220V-240V
1
3
4
2
(except Europe and Russia models)(Europe and Russia models)
8 En
Functional overview
■ Remote control
(For DVR-1000)
For details on how to use the remote control, see page 20.
1 STANDBY/ON ( )
Turns on the DVD receiver, or sets it to the standby
mode.
2 Numeric keypad (0 – 9)
Enters a track/title number of the disc.
Enters a number of a preset radio station.
3 TREBLE/BASS
Selects the TREBLE (high tone) or BASS (low tone)
sound mode.
Use the VOLUME control to change the tone level.
4 REPEAT
Selects various repeat modes.
FREQ/TEXT
TUNER mode: switches the information display when
receiving Radio Data System.
5 REPEAT A-B
Repeats a specific section on a disc.
6 h
DVD/CD mode: starts disc playback.
USB mode: starts playback.
7 ON SCREEN
Displays the current status or disc information.
8 ENTER
Confirms a selection.
9 SET UP
Enters or exits the system setup menu.
0 AREA
Select either the WIDE or NARROW listening area
(see page 47).
A MODE
Select the Virtual Surround mode (see page 47).
B ENHANCER
Switches the Enhancer mode on or off (see page 47).
C SURROUND
Turns the surround effect on or off (see page 47).
D Input selection buttons
Selects the appropriate active source mode.
DVD/CD: switches to DVD/CD mode.
AUX: switches to ANALOG/FRONT IN/DIGITAL
input.
TUNER: switches to tuner (FM/AM) input.
USB: switches to USB mode. Accesses the contents of
the connected USB device or exits from the USB
mode (see page 31).
E SUBTITLE
Selects a subtitle language.
F ANGLE
Selects a DVD disc camera angle (if available).
Note
STANDBY/ON
EJECT
DIMMER
BASS TREBLE
ENTER
DIRECT
DVD/CD
TUNER
SURROUND
AUX
SUBTITLE
ANGLE ZOOM AUDIO
MUTE
AREA
MODE
USB
ENHANCER
NIGHT
REPEAT
ON SCREEN
MENU
SET UP
TOP MENU
/RETURN
FREQ/TEXT
MODE START
PRESET PRESET
PROG
A-B
SHUFFLE
SLEEP
PTY SEEK
P
Q
R
S
t
U
V
W
7
8
9
0
A
B
C
D
E
F
G
H
1
2
3
4
5
6
I
J
K
L
N
O
M
9 En
Functional overview
English
INTRODUCTION
1
G EJECT ( )
Ejects a disc in the DVD receiver.
H SLEEP
Sets the sleep timer (see page 49).
I DIMMER
Selects different levels of brightness for the display
panel (see page 49).
J NIGHT
Turns the Night listening mode on or off
(see page 48).
K s
Exits an operation.
DVD/CD mode: stops disc playback.
DVD/CD mode: holding down the button will eject
the disc.
TUNER mode: erases a preset radio station if held for
more than two seconds.
USB mode: stops playback.
L PROG
DVD/CD mode: starts programming.
TUNER mode: starts automatic/manual preset
programming if held for more than two seconds.
M SHUFFLE
Plays tracks in random order.
PTY SEEK START
TUNER mode: starts searching for a Radio Data
System station.
N e
DVD/CD mode: pauses disc playback.
USB mode: pauses playback.
PTY SEEK MODE
TUNER mode: sets the DVD receiver to the PTY
SEEK mode.
O b / a
DVD/CD mode: selects the previous/next track or
chapter. Press and hold to fast forward or fast reverse.
USB mode: selects the previous/next track. Press and
hold to fast forward or fast reverse.
d PRESET u
TUNER mode: press to select a preset radio station.
P MENU
Enters or exits the disc contents menu.
For VCD version 2.0 only:
In stop mode, turns on/off playback control (PBC)
mode.
During playback, returns to the main menu.
Q Cursors ( / / / )
Selects movement direction in the menu.
TUNER mode: press left or right to tune the radio
frequency.
TUNER mode: press up or down to select auto tuning.
R TOP MENU/RETURN
Returns to the previous menu.
Displays the top-level disc menu
(if available).
S DIRECT
Switches the video output on or off during audio disc
playback.
This function (Audio Direct) is not available for
HDMI output.
In the DIRECT mode, the display panel dims to “DIM
2 (40% brightness)”.
T VOLUME (+/–)
Adjusts the volume level.
U MUTE
Mutes or restores the volume.
V AUDIO
Selects an audio language (DVD) or an audio channel
(VCD).
W ZOOM
Enlarges or reduces the TV screen picture.
10 En
PREPARATION
■ Roles and layout of the speakers
To enjoy quality sounds you need to place the speakers in their appropriate positions and install them correctly.
The following show the recommended layout of the speakers.
For the best possible surround sound, all of the speakers (except the subwoofer) should be placed at the same distance
from the listening position.
1 Front Speakers (L, R)
Place the front left/right speakers on both sides of your TV at equal distances.
Main roles: Produces front channel (stereo) sounds and effect sounds.
2 Subwoofer
Place the subwoofer near a front speaker and turn it slightly toward the center of the room to reduce wall reflections.
Main roles: Produces bass sounds and low frequency (LFE) sounds contained in Dolby Digital or DTS.
To avoid magnetic interference, do not position the front speakers too close to your TV.
Allow adequate ventilation around the DVD receiver and subwoofer.
Bass sounds produced by the subwoofer may be heard differently depending on the listening position and subwoofer location.
To enjoy desired sounds, try to change the location of the subwoofer according to the listening position.
Connections
1
2
1
DVD receiver
Front
speaker (R)
Subwoofer
Front
speaker (L)
Note
11 En
English
PREPARATION
2
■ Connecting the speakers
– Do not connect the power cord of the subwoofer and DVD receiver into an AC outlet until all cable connections
are completed.
– Be sure to connect the end of the supplied speaker cable (where the red and black cable lengths differ) to the front
speaker, and leave some slack.
– Be sure to connect the red cable to the red terminal (subwoofer and front speakers) and the black cable to the
black terminal.
System connections
Notes
SYSTEM
CONNECTOR
6
ΩMIN. /SPEAKER
SPEAKERS
MAINS
L
R
SYSTEM
CONNECTOR
MAINS
TO SUBWOOFER
AUX IN
AUDIO
LINE OUT
AV MONITOR OUT
(
DVD ONLY
)
S VIDEO
VIDEO
COMPONENT
Y
P
R
PB
PCM/DTS
q
DIGITAL
OPTICAL
DIGITAL IN
VIDEO OUT
(DVD ONLY)
AM
ANT
GND
TUNER
HDMI
FM
ANT
75Ω UNBAL
L
R
L
R
R L
Front speaker (R)
Subwoofer
DVD receiver
Front speaker (L)
System connections
12 En
Connecting the speaker cables
– Be sure to connect the end of the supplied speaker
cable (where the red and black cable lengths differ)
to the front speaker, and leave some slack.
– Be sure to connect the red cable to the red terminal
(subwoofer and front speakers) and the black cable
to the black terminal.
1 Remove approximately 10 mm (0.4 in) of insulation
from the end of each speaker cable and then twist the
exposed wires of the cable together to prevent short
circuits.
2 Loosen the knob.
3 Insert one bare wire into the hole in the center of each
terminal.
4 Tighten the knob to secure the wire.
Connecting the subwoofer
Be sure to connect the red cable to the red terminal
(subwoofer and front speakers) and the black cable to the
black terminal.
1 Remove approximately 10 mm (0.4 in) of insulation
from the end of each speaker cable and then twist the
exposed wires of the cable together to prevent short
circuits.
2 Loosen the knob.
3 Insert one bare wire into the hole on the side of each
terminal.
4 Tighten the knob to secure the wire.
Notes
10 mm (0.4 in)
Red: positive (+)
Black: negative (–)
Note
10 mm (0.4 in)
R
L
Red: positive (+)
Black: negative (–)
R
L
R
L
System connections
13 En
English
PREPARATION
2
Connecting the DVD receiver and the
subwoofer
Connect the subwoofer to the DVD receiver using the
system control cable. Attach one end to the subwoofer and
the other to the SYSTEM CONNECTOR terminal at the
rear of the DVD receiver.
– When connecting the system control cable, be sure
to insert the plug until it clicks. When
disconnecting the system control cable, slide the
collar of the plug back to unlock.
– Ensure that the speaker cables are correctly
connected. Improper connections may damage the
system due to a short-circuit.
– When connecting the speakers, fix the speaker
cables in place so that cables do not loosen. If your
foot or hand accidentally gets caught on a loose
speaker cable, the speaker may fall.
– To prevent unwanted noise, do not place the
subwoofer too close to the DVD receiver, AC
power adaptor, TV or other sources of radiation.
– Be sure to connect the power cable of the
subwoofer (NX-SW1000) to the AC outlet before
you turn on the DVD receiver (DVR-1000).
Otherwise, the subwoofer (NX-SW1000) will not
be powered correctly.
Notes
SYSTEM
CONNECTOR
MAINS
L
R
6
ΩMIN. /SPEAKER
SPEAKERS
L
R
SYSTEM
CONNECTOR
MAINS
TO SUBWOOFER
AUX IN
AUDIO
LINE OUT
AV MONITOR OUT
(
DVD ONLY
)
S VIDEO
VIDEO
COMPONENT
Y
P
R
PB
PCM/DTS
q
DIGITAL
OPTICAL
DIGITAL IN
VIDEO OUT
(DVD ONLY)
AM
ANT
GND
TUNER
HDMI
FM
ANT
75Ω UNBAL
L
R
L
R
SYSTEM
CONNECTOR
SYSTEM
CONNECTOR
NX-SW1000
14 En
■ Connecting a TV
– You only need to make one video connection from the following options (A, B, C, or D), depending on the
capabilities of your TV.
– Do not connect the power cords until all cable connections are completed.
COMPONENT VIDEO OUT jacks <A>
Use the component video cables (red/blue/green, not
supplied) to connect the DVD receiver’s Y P
B PR jacks to
the corresponding component video input jacks (or the Y
Pb/Cb Pr/Cr/ YUV jacks) on your TV.
Progressive scan video quality is only available when
using Y PB PR in conjunction with a progressive scan TV.
To activate the progressive scan function see “Progressive
function” on page 40.
VIDEO output jack <B>
Use a composite video cable (yellow -supplied) to connect
the DVD receiver’s VIDEO output jack to the video input
jack (or A/V In/Video In/Composite/Baseband jack) on
your TV.
S VIDEO output jack <C>
S (separate)-video connections achieve a clearer picture
than composite video connections. Use an S-video cable
(not supplied) to connect the DVD receiver’s
S VIDEO output jack to the S-video input jack (or Y/C or
S-VHS jack) on your TV.
AV MONITOR OUT terminal <D>
(Europe and Russia models only)
The SCART cable, or “Euro AV cable”, supports AV
MONITOR OUT signal transmission, providing you with
the best possible picture and sound. If your TV has only
one terminal for video input, and you want to connect it
directly to the DVD receiver, you can use the AV
MONITOR OUT connector. Connect one end of the
SCART cable to the AV MONITOR OUT connector and
the other end to the SCART connector on your TV.
– TV channels, if you use AV MONITOR OUT
terminal to connect the TV. To use AV MONITOR
OUT terminal, make sure to set the DVD
receiver’s component setting to “RGB” (see
page 22).
– When using AV MONITOR OUT terminal to
listen to the TV channels, set the DVD receiver’s
component setting to “RGB” (see page 22).
– S-video signal is not output at AV MONITOR
OUT terminal.
Other connections
Notes
M
O
R
AUX IN
AUDIO
LINE OUT
AV MONITOR OUT
(
DVD ONLY
)
S VIDEO
VIDEO
COMPONENT
Y
P
R
PB
PCM/DTS
q
DIGITAL
OPTICAL
DIGITAL IN
VIDEO OUT
(DVD ONLY)
L
R
L
R
TV
<A>
<C>
<D>
<B>
Notes
Other connections
15 En
English
PREPARATION
2
■ Connecting an HDMI component
HDMI (High-Definition Multimedia Interface) is the first
industry-supported, uncompressed, all-digital A/V (audio/
video) interface.
By connecting to an HDMI component (such as a TV),
you can enjoy standard, enhanced or high-definition video
as well as multi-channel digital audio using a single cable.
When used in combination with HDCP (High-bandwidth
Digital Content Protection), HDMI provides a secure
audio/video interface that meets the security requirements
of content providers and system operators.
For further information on HDMI, visit the HDMI website
at “http://www.hdmi.org/”.
Viewing and Listening to playback
from an HDMI component
1 Connect HDMI terminal of the DVD receiver to the
HDMI input terminal of your HDMI compatible
component using a commercially available HDMI
cable.
2 Select the appropriate audio output from [HDMI
AUDIO OUT] in [AUDIO SETUP PAGE] (see
page 36).
3 Select the appropriate video output from [HDMI
VIDEO] in [VIDEO SETUP PAGE] (see page 39).
– The DVD receiver is not compatible with HDCP-
incompatible HDMI or DVI components.
– You need a commercially available HDMI/DVI
conversion cable when you connect the DVD
receiver to other DVI components.
– When connecting an HDMI component, refer to
the instruction manual for the component.
– Do not disconnect or connect the HDMI cable from
the DVD receiver or turn off the power of the
HDMI/DVI component connected to the HDMI
terminal of the DVD receiver while data is being
transferred. Doing so may disrupt playback or
cause noise.
Notes
L
R
AV MONITOR OUT
(
DVD ONLY
)
AM
ANT
GND
TUNER
HDMI
FM
ANT
75Ω UNBAL
HDMI
IN
TV
DVD receiver
Other connections
16 En
HDMI audio output
*1
The audio output is automatically changed from multi-channel audio signals to downmixed stereo signals.
*2
If the connected HDMI component does not support bitstream signals (Dolby Digital, DTS, and MPEG), the audio output is
automatically changed from bitstream signals to PCM signals.
*3
If the connected HDMI component does not support multi-channel audio signals, the audio output is automatically changed from
PCM multi-channel signals to PCM stereo signals and 48 kHz/16 bits signals or less.
*4
If the connected HDMI component does not support more than 48 kHz, the audio output is automatically changed to 48 kHz/16 bits
signals or less.
You need to set [HDMI AUDIO OUT] (see page 36).
Audio format Analog output
HDMI AUDIO OUT
AUTO PCM OFF
DVD-Video
Dolby Digital Multi-
channel
Multi
*1
Dolby Digital
*2,3
PCM 2-channel Off
Stereo
Dolby Digital
2-channel
Multi
*1
/Stereo Dolby Digital
*2
DTS
Multi-channel
Multi
*1
DTS
*2,3
Stereo
DTS 2-channel Multi
*1
/Stereo DTS
*2
MPEG
Multi-channel
Multi
*1
MPEG
*2,3
Stereo
MPEG 2-channel Multi
*1
/Stereo MPEG
*2
PCM 2-channel
*4
Multi
*1
/Stereo PCM 2-channel
CD/MP3/WMA/
DivX
®
2-channel Multi
*1
/Stereo PCM 2-channel
DTS-CD
Multi-channel
Multi
*1
DTS
*2,3
Stereo
2-channel Multi
*1
/Stereo DTS
*2
VCD 2-channel Multi
*1
/Stereo PCM 2-channel
SVCD
Multi-channel
Multi
*1
MPEG
*2,3
Stereo
2-channel Multi
*1
/Stereo MPEG
*2
Note
Other connections
17 En
English
PREPARATION
2
■ Connecting the FM/AM antennas
1 Connect an AM loop antenna to the AM ANT
terminal. Place the AM loop antenna on a shelf or
attach it to a stand or wall.
2 Connect an indoor FM antenna to the FM ANT
terminal. Extend the FM antenna and fix its ends to
the wall.
For better FM stereo reception, connect an external
FM antenna.
– Adjust the position of the antennas for optimal
reception.
– Position the antennas as far as possible from your
TV, VCR or other sources of radiation to prevent
unwanted interference.
Notes
AM
ANT
GND
TUNER
HDMI
FM
ANT
75Ω UNBAL
1
2
Ground (GND terminal)
For minimum interference, connect
the antenna GND terminal to a
good earth ground. A good earth
ground is a metal stake driven into
moist earth.
FM antenna
AM loop
antenna
Other connections
18 En
■ Connecting external AV components
If you connect external AV equipment such as a VCR, cassette deck or digital audio component to the following audio
terminals on the DVD receiver, you can enjoy those audio sources with the DVD receiver. Also, you can record AV
sources played on the DVD receiver using the recording equipment. This section provides some examples of other AV
equipment connections. For information on your AV equipment, refer to the manual provided.
Viewing and listening to playback
1 Connect the DVD receiver’s VIDEO output jack to
the VIDEO IN jack on your VCR. Or, connect the
VCR to the TV as shown.
2 Connect the DVD receiver’s AUX IN jacks to the
AUDIO OUT jacks on your VCR.
Before starting operation, press AUX to select
“ANALOG” in order to activate the input source.
Using the VCR for recording DVD
playback
Some DVDs are copy-protected. You cannot record or
dub protected discs using a VCR.
1 Connect the DVD receiver’s VIDEO output jack to
the VIDEO IN jack on your VCR. Or, connect the
DVD receiver’s S VIDEO output jack to the S-
VIDEO IN jack on your VCR.
2 Connect the DVD receiver’s LINE OUT jacks to the
AUDIO IN jacks on your VCR.
This will allow you to make analog stereo (two
channels, right and left) recordings.
AUX IN
AUDIO
LINE OUT
S VIDEO
VIDEO
COMPONENT
Y
P
R
PB
/
DTS
G
ITAL
C
AL
A
L IN
VIDEO OUT
(DVD ONLY)
L
R
L
R
1
2
12
VCR (for example)
DVD receiver
TV
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/