Pioneer AVD-W7900 Руководство пользователя

Owner’s Manual

Mode d’emploi

7-INCH REAR SEAT ENTERTAINMENT DISPLAY

AFFICHAGE DIVERTISSANT 7 POUCES POUR

SIEGES ARRIERE

AVD-W7900

This product conforms to new cord colors.

Los cables de este producto son conformes a un nuevo

código de colores.

Dieses Produkt entspricht den neuen Kabelfarben.

Ce produit respecte un nouveau code de couleur des

câbles.

Questo prodotto è conforme ai nuovi codici colori.

De kleuren van de snoeren van dit toestel zijn gewijzigd.

Данное устройство соответствует новым

требованиям к цвету проводов.

English NederlandsItalianoFrançaisDeutschEspañol Русский

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate

your model properly. After you have finished reading the instructions, k eep this man-

ual in a safe place for future reference.

Precautions

IMPORTANT SAFEGUARDS 3

To ensure safe driving 3

– When using a display connected to

VIDEO OUTPUT 3

To avoid battery exhaustion 4

Before You Start

About this unit 5

Visit our website 5

In case of trouble 5

To protect the LCD screen 5

For viewing LCD comfortably 6

– Changing the wide screen size 6

– Changing the picture adjustment 6

Installing and removing the display unit 6

– Installing the display unit 6

– Removing the display unit 7

Resetting the microprocessor 7

Operating this unit

What’s What 8

– Display unit 8

Basic Operations 8

– Power ON/OFF 8

– Selecting a source 8

– Changing the wide screen mode 8

– Switching the dimmer setting 9

Setup 9

– Changing the picture adjustment 9

– Selecting the video format 10

Connection and installation

Connections 11

– Connection Diagram 12

Installation 13

– Mounting with flush mounting

bracket 13

– Removing the display unit 13

Additional Information

Using the display correctly 14

– Handling the display 14

– Liquid crystal display (LCD) screen 14

– Keeping the display in good

condition 14

– Small fluorescent tube 15

Specifications 16

Contents

En

2

IMPORTANT SAFEGUARDS

Please read all of these instructions regarding

your display and retain them for future refer-

ence.

1 Read this manual fully and carefully be-

fore operating your display.

2 Keep this manual handy as a reference for

operating procedures and safety informa-

tion.

3 Pay close attention to all warnings in this

manual and follow the instructions care-

fully.

4 Do not allow other persons to use this sys-

tem until they have read and understood

the operating instructions.

5 Do not install the display where it may (i)

obstruct the driver’s vision, (ii) impair the

performance of any of the vehicle’s oper-

ating systems or safety features, includ-

ing air bags, hazard lamp buttons or (iii)

impair the driver’s ability to safely oper-

ate the vehicle.

6 As with any accessory in your vehicle’s in-

terior, the display should not divert your

attention from the safe operation of your

vehicle. If you experience difficulty in op-

erating the system or reading the display,

please park safely before making adjust-

ments.

7 Please remember to wear your seat belt at

all times while operating your vehicle. If

you are ever in an accident, your injuries

can be considerably more severe if your

seat belt is not properly buckled.

WARNING

! Do not attempt to install or service your

display by yourself. Installation or servi-

cing of the display by persons without

training and experience in electronic

equipment and automotive accessories

may be dangerous and could expose you

to the risk of electric shock or other ha-

zards.

WARNING

! NEVER install this display in a location

where it is visible by the driver. Doing so

can cause the driver to be distract by

images while the vehicle is in motion.

! Use of this display is subject to all govern-

ment laws regarding placement or use.

! PIONEER does not accept any liability for

any problems, damage or loss incurred as

a result of the display being used with an

incorrect setting or in violation of any gov-

ernment laws.

To ensure safe driving

WARNING

! To avoid the risk of accident and the potential

violation of applicable laws, rear display units

should not be in a location where it is a visible

distraction to the driver.

! This display is designed solely for use from

the rear seats. NEVER install the display in a

location that enables the driver to watch

images while driving.

! In some countries or states the viewing of

images on a display inside a vehicle even by

persons other than the driver may be illegal.

Where such regulations apply, they must be

obeyed and display units should not be used.

When using a display

connected to VIDEO OUTPUT

This unit’s VIDEO OUTPUT is for connection

of a display to enable passengers in the rear

seats to watch the DVD or TV.

Precautions

En

3

English

Section

01

WARNING

NEVER install the rear display in a location that

enables the driver to watch the DVD or TV while

driving.

To avoid battery exhaustion

Be sure to run the vehicle engine while using

this unit. Using this unit without running the

engine can result in battery drainage.

Precautions

En

4

Section

01

If you want to dispose this product, do not mix

it with general household waste. There is a se-

parate collection system for used electronic

products in accordance with legislation that re-

quires proper treatment, recovery and recy-

cling.

Private households in the member states of

the EU, in Switzerland and Norway may return

their used electronic products free of charge

to designated collection facilities or to a retai-

ler (if you purchase a similar new one).

For countries not mentioned above, please

contact your local authorities for the correct

method of disposal.

By doing so you will ensure that your disposed

product undergoes the necessary treatment,

recovery and recycling and thus prevent po-

tential negative effects on the environment

and human health.

About this unit

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with liquids.

! Keep this manual handy as a reference for op-

erating procedures and precautions.

! Always keep the volume low enough so that

you can hear sounds from outside the vehicle.

! Protect this unit from moisture.

Visit our website

Visit us at the following site:

! Register your product. We will keep the de-

tails of your purchase on file to help you

refer to this information in the event of an

insurance claim such as loss or theft.

! We offer the latest information about

Pioneer Corporation on our website.

In case of trouble

Should this product fail to operate properly,

contact your dealer or nearest authorized

Pioneer Service Station.

To protect the LCD screen

! Do not allow direct sunlight to fall on the

display when this unit is not being used.

Extended exposure to direct sunlight can

result in LCD screen malfunction due to

the resulting high temperatures.

! When using a cellular phone, keep the an-

tenna of the cellular phone away from the

display to prevent disruption of the video by

the appearance of spots, colored stripes,

etc.

! Never touch the screen with anything be-

sides your finger when operating the touch

panel function. The screen can scratch

easily.

Before You Start

En

5

English

Section

02

For viewing LCD comfortably

Due to its construction, the viewing angle of

the LCD screen is limited. You can adjust it by

changing either screen size or picture adjust-

ment.

Changing the wide screen size

By changing the screen size from 4:3 to 16:9,

you can adjust the screen so that the screen

can fit to the video image you are playing.

For details concerning operation, refer to

Changing the wide screen mode on page 8.

Changing the picture adjustment

You can make the best adjustment to the pic-

ture display by changing BRIGHTNESS,

CONTRAST, COLOR and HUE. You can also

dim or enlight the overall picture image using

DIMMER.

For details concerning operation, refer to

Changing the picture adjustment on page 9.

Installing and removing

the display unit

The mounting arm described below is sold se-

parately. For more information on the installa-

tion, refer to the mounting kit owner’s manual

or consult your nearest dealer.

Important

! To prevent failure, be sure to turn the ignition

switch or system power OFF before installing

or removing the display unit. Also take care

not to grip the screen or buttons too firmly

and not to drop the display unit.

! Do not let any water get on the terminals on

the display unit or on the cable and do not

allow the terminals to be shorted by a metal

object or the like. This can cause system

breakdown.

! Be careful not to touch terminals on the dis-

play unit or on the cable. Doing so may cause

connection failures. If any terminals are dirty,

wipe them with a clean dry cloth.

Installing the display unit

1 Align the bracket into the grooves of

the base.

Mounting arm

(sold separately)

Bracket

Base

2 Slide the display unit until it clicks into

place.

Before You Start

En

6

Section

02

3 Connect the cable to the display unit.

Removing the display unit

To deter theft of the display unit, remove the

display unit when leaving the vehicle.

1 Hold down the release section and un-

plug the connector.

2 Unlock the lock release lever, then slide

the display unit and detach it from the

base.

Mounting arm

(sold separately)

Base

Lock release lever

Resetting the microprocessor

You can reset the microprocessor to its initial

settings.

The microprocessor must be reset under the

following conditions:

! Prior to using this unit for the first time

after installation

! If the unit fails to operate properly

! When strange or incorrect messages ap-

pear on the display

1 Press SOURCE/POWER and hold until

the unit turns off.

2 Hold down SOURCE/POWER and d

simultaneously.

Before You Start

En

7

English

Section

02

What’s What

Display unit

1 SOURCE/POWER button

This unit is turned on by selecting a source.

Press to cycle through all the available

sources.

Press and hold to turn the unit off.

2 c/d buttons

Press to change the settings when the

setup menu is displayed.

3 WIDE/MENU button

Press to select a desired mode for enlarging

a 4:3 picture to a 16:9 one.

Press and hold to display the setup menu.

4 DIMMER button

Press to switch between the dimmer levels.

5 IR transmitter

You can listen to stereo audio with sepa-

rately sold cordless headphones (e.g., SE-

IRM290).

Basic Operations

Power ON/OFF

Turning the unit on

% Press SOURCE/POWER to turn the unit

on.

When you select a source, the unit is turned

on.

Turning the unit off

% Press SOURCE/POWER and hold until

the unit turns off.

Note

Take off your headphones when turning the dis-

play unit on or off. If you leave your headphones

on, a noise may be heard when the volume is

high.

Selecting a source

You can select a source you want to listen to.

! This unit is equipped with two video inputs,

VIDEO 1 INPUT and VIDEO 2 INPUT.

% Press SOURCE/POWER to select a

source.

Press SOURCE/POWER repeatedly to switch

between the following sources:

VCR1 (VCR1)—VCR2 (VCR2)

Changing the wide screen mode

You can select a desired mode for enlarging a

4:3 picture to a 16:9 one.

% Press WIDE/MENU to select the desired

setting.

Press WIDE/MENU repeatedly to switch be-

tween the following settings:

FULL (full)—JUST (just)—CINEMA (cinema)—

ZOOM (zoom)—NORMAL (normal)

1

3

4

2

5

Operating this unit

En

8

Section

03

FULL (full)

A 4:3 picture is enlarged in the horizontal direc-

tion only, giving you a 4:3 TV picture (normal pic-

ture) without any omissions.

JUST (just)

The picture is enlarged slightly at the center and

the amount of enlargement increases horizontally

to the ends, enabling you to enjoy a 4:3 picture

without sensing any disparity even on a wide

screen.

CINEMA (cinema)

The picture is enlarged by the same proportion as

FULL or ZOOM in the horizontal direction and by

an intermediate proportion between FULL and

ZOOM in the vertical direction; ideal for a cine-

ma-sized picture (wide screen picture) where cap-

tions lie outside.

ZOOM (zoom)

A 4:3 picture is enlarged in the same proportion

both vertically and horizontally; ideal for a cine-

ma-sized picture (wide screen picture).

NORMAL (normal)

A 4:3 picture is displayed as it is, giving you no

sense of disparity since its proportions are the

same as that of the normal picture.

Notes

! When video is viewed in a wide screen mode

that does not match its original aspect ratio, it

may appear different.

! Remember that using the wide mode feature

of this system for commercial or public view-

ing purposes may constitute an infringement

on the author’s rights protected by the Copy-

right Law.

! The video image will appear coarser when

viewed in CINEMA or ZOOM mode.

Switching the dimmer setting

To prevent the display from being too bright at

night or when the ambient brightness be-

comes dark, you can dim the display.

% Press DIMMER to select the desired

level.

Press DIMMER repeatedly to switch between

the following levels:

DIMMER HIGH (high)—DIMMER MID (mid)

—DIMMER LOW (low)

Setup

Changing the picture adjustment

You can adjust BRIGHTNESS (brightness),

CONTRAST (contrast), COLOR (color) and

HUE (hue) for each source.

1 Press WIDE/MENU and hold to display

the setup menu.

BRIGHTNESS appears on the display.

2 Press WIDE/MENU to display the ad-

justment function names.

Press WIDE/MENU repeatedly to switch be-

tween the following adjustment functions:

BRIGHTNESS (brightness)—CONTRAST (con-

trast)—COLOR (color)—HUE (hue)—

COLOR SYSTEM (color system)—Exit from

the setup menu

3 Press c or d to adjust the selected

item.

Each press of c or d increases or decreases

the level of selected item. +24 to –24 is dis-

played as the level is increased or decreased.

! BRIGHTNESS – Adjust the black intensity

! CONTRAST – Adjust the contrast

! COLOR – Adjust the color saturation

! HUE – Adjust the tone of color (red is em-

phasized or green is emphasized)

Operating this unit

En

9

English

Section

03

# If you do not operate the function within about

eight seconds, the display is automatically re-

turned.

Selecting the video format

When this unit is connected to an AV equip-

ment, you need to adjust the video format sui-

table to that AV equipment.

1 Press WIDE/MENU and hold to display

the setup menu.

BRIGHTNESS appears on the display.

2 Press WIDE/MENU to display

COLOR SYSTEM.

Press WIDE/MENU repeatedly to switch be-

tween the following adjustment functions:

BRIGHTNESS (brightness)—CONTRAST (con-

trast)—COLOR (color)—HUE (hue)—

COLOR SYSTEM (color system)—Exit from

the setup menu

3 Press c or d to select the desired video

format.

Each press of c or d selects the video format

in the following order:

AUTO—PAL—PAL-M—SECAM—NTSC

# If AUTO is selected, NTSC, PAL, PAL-M and

SECAM are automatically identified and dis-

played.

# Broadcast reception may be inferior when

AUTO is selected.

# If you do not operate the function within about

eight seconds, the display is automatically re-

turned.

Operating this unit

En

10

Section

03

CAUTION

! PIONEER does not recommend that you in-

stall or service your display unit yourself. In-

stalling or servicing the product may expose

you to risk of electric shock or other hazards.

Refer all installation and servicing of your dis-

play unit to authorized Pioneer service person-

nel.

! Secure all wiring with cable clamps or electri-

cal tape. Do not allow any bare wiring to re-

main exposed.

! Do not drill a hole into the engine compart-

ment to connect the yellow cable of the dis-

play unit to the vehicle battery. Engine

vibration may eventually cause the insulation

to fail at the point where the wire passes from

the passenger compartment into the engine

compartment. Take extra care in securing the

wire at this point.

! Make sure that cables will not interfere with

moving parts of the vehicle, such as the gear-

shift, parking brake or seat sliding mechan-

ism.

! Do not shorten any cables. If you do, the pro-

tection circuit may fail to work properly.

Connections

Important

! When this unit is installed in a vehicle without

ACC (accessory) position on the ignition

switch, red cable must be wired to the term-

inal that can detect the operation of the igni-

tion key. Otherwise, battery drain may result.

A

C

O

N

S

T

A

R

T

O

F

O

N

S

T

A

R

T

O

F

ACC posi-

tion

No ACC po-

sition

! Use of this unit in conditions other than the

following could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or ad-

hesive tape. To protect the wiring, wrap ad-

hesive tape around them where they lie

against metal parts.

— Place all cables away from moving parts,

such as gear shift and seat rails.

— Place all cables away from hot places,

such as near the heater outlet.

— Do not pass the yellow cable through a

hole into the engine compartment to con-

nect to a battery.

— Cover any disconnected cable connectors

with insulating tape.

— Do not remove RCA caps if RCA cables are

not used.

— Do not shorten any cables.

— Never cut the insulation of the power cable

of this unit in order to share the power

with other devices. Current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

Cord function may differ according to the pro-

duct, even if cord color is the same. When con-

necting this system, be sure to check all

manuals and connect cords correctly.

Connection and

installation

En

11

English

Section

04

Connection Diagram

Black (chassis ground)

Connect to a clean, paint-free metal location.

Fuse resistor

Red

Connect to terminal controlled by ignition switch (12 V DC).

Fuse (4 A)

Yellow

Connect to the constant 12 V supply terminal.

Power cable

Black

Display unit

4 m

External video

component

(sold separately)

Video 1 input (VIDEO 1 INPUT)

Audio 1 input (AUDIO 1 INPUT)

Connect to video output

Connect to audio outputs

Video 2 input (VIDEO 2 INPUT)

Audio 2 input (AUDIO 2 INPUT)

Video output (VIDEO OUTPUT)

Audio output (AUDIO OUTPUT)

Connect to video 1 input

Connect to audio 1 input

Remote control signal output (REMOTE CONTROLLER

SIGNAL OUTPUT): Not used.

3 m

AVD-W7900

(sold separately)

Connect to the terminal which is not interlocked to

the volume adjustment.

Connection and

installation

En

12

Section

04

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts. Use of un-

authorized parts may cause malfunctions.

! Consult your dealer if installation requires dril-

ling of holes or other modifications to the vehi-

cle.

! Do not install this unit where :

— it may interfere with operation of the vehi-

cle.

— it may cause injury to a passenger as a re-

sult of a sudden stop.

Mounting with flush mounting

bracket

1 Install securely the mounting bracket in

a safety location by using the supplied tap-

ping screws (M4 × 12).

2 Place the display unit into the mount-

ing bracket until it clicks.

Removing the display unit

% Insert the release plates to gaps be-

tween the display unit and the mounting

bracket.

The display unit will be released.

# Never apply with much force to the display

unit, the mounting bracket or the release plates

as this may damage it.

Connection and

installation

En

13

English

Section

04

Using the display correctly

CAUTION

! If liquid or foreign matter should get inside

this unit, turn off the power immediately and

consult your dealer or the nearest authorized

PIONEER Service Station. Do not use the unit

in this condition because doing so may result

in a fire, electric shock, or other failure.

! If you notice smoke, a strange noise or smell,

or any other abnormal signs from the display,

turn off the power immediately and consult

your dealer or the nearest authorized

PIONEER Service Station. Using this unit in

this condition may result in permanent da-

mage to the system.

! Do not disassemble or modify this unit, as

there are high-voltage components inside

which may cause an electric shock. Be sure

to consult your dealer or the nearest author-

ized PIONEER Service Station for internal in-

spection, adjustments or repairs.

Handling the display

! When the display is subjected to direct sun-

light for a long period of time, it will be-

come very hot resulting in possible

damage to the LCD screen. When not

using this unit, avoid exposing it to direct

sunlight.

! The display should be used within the tem-

perature ranges shown below.

Operating temperature range: -20 °C to +60

°C

Storage temperature range: -40 °C to +95

°C

At temperatures higher or lower than the

operating temperature range the display

may not operate normally.

! The LCD screen of this unit is exposed in

order to increase its visibility within the ve-

hicle. Please do not press strongly on it as

this may damage it.

! Do not push the LCD screen with much

force as this may scratch it.

Liquid crystal display (LCD) screen

! If the display is installed near the vent of an

air conditioner, make sure that air from the

air conditioner is not blowing on it. Heat

from the heater may damage the LCD

screen, and cool air from the cooler may

cause moisture to form inside the display

resulting in possible damage. Also, if the

display is cooled down by the cooler, the

screen may become dark, or the life span

of the small fluorescent tube used inside

the display may be shortened.

! Small black dots or white dots (bright dots)

may appear on the LCD screen. These are

due to the characteristics of the LCD

screen and do not indicate a problem with

the display.

! At low temperatures, the LCD screen may

be dark for a while after the power is turned

on.

! The LCD screen will be difficult to see if it is

exposed to direct sunlight.

! When using a portable phone, keep the an-

tenna of the portable phone away from the

display to prevent disruption of the video by

the appearance of spots, colored stripes,

etc.

Keeping the display in good

condition

! When removing dust from the screen or

cleaning the display, first turn the system

power off, then wipe with a soft dry cloth.

! When wiping the screen, take care not to

scratch the surface. Do not use harsh or

abrasive chemical cleaners.

Additional Information

En

14

Appendix

Small fluorescent tube

! A small fluorescent tube is used inside the

display to illuminate the LCD screen.

— The fluorescent tube should last for ap-

proximately 10 000 hours, depending on

operating conditions. (Using the display

at low temperatures reduces the service

life of the fluorescent tube.)

— When the fluorescent tube reaches the

end of its useful life, the screen will be

dark and the image will no longer be

projected. If this happens, consult your

dealer or the nearest authorized

PIONEER Service Station.

Additional Information

En

15

English

Appendix

Specifications

General

Power source ............................. 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system ................... Negative type

Max. current consumption

..................................................... 0.7 A

Storage temperature range

..................................................... -40 °C to +95 °C

Display unit

Dimensions (W × H × D) ...178 × 118 × 32 mm

Weight .......................................... 480 g

Screen size/aspect ratio ....... 7.0 inch wide/16:9

(effective display area: 154

× 87 mm)

Pixels ............................................. 336 960 (1 440 × 234)

T ype ................................................ TFT active matrix, transmis-

sive type

Color system .............................. NTSC/PAL/PAL-M/SECAM

compatible

Video input level ....................... 1.0 Vp-p/75 W

Max. audio input level ........... 1.5 Vrms/22 kW

Video output level .................... 1.0 Vp-p/75 W

Max. audio output level ........ 1.5 Vrms/1 kW

Operating temperature range

..................................................... -20 °C to +60 °C

Installation bezel

Dimensions (W × H × D) ...201 × 141 × 35 mm

Weight .......................................... 100 g

Note

Specifications and the design are subject to mod-

ifications without notice due to improvements.

Additional Information

En

16

Appendix

Gracias por haber comprado este producto Pioneer.

Lea con detenimiento esta s instrucciones sobre el funcionamiento del aparato,

para que pueda darle el mejor uso posible. Una vez que las haya leído, conserve

este manual en un lugar seguro para consultarlo en el futuro.

Precauciones

INSTRUCCIONES DE SEGURIDAD

IMPORTANTES 18

Para garantizar la conducción segura del

vehículo 18

– Al utilizar un display conectado con la

salida VIDEO OUTPUT 19

Para evitar la descarga de la batería 19

Antes de comenzar

Acerca de esta unidad 20

Visite nuestro sitio Web 20

En caso de problemas 20

Para proteger la pantalla LCD 20

Para visualizar la pantalla LCD con

comodidad 21

– Cambio del modo panorámico 21

– Cambio del ajuste de la imagen 21

Instalación y retirada de la unidad de

display 21

– Instalación de la unidad de display 22

– Retirada de la unidad de display 22

Reinicialización del microprocesador 22

Utilización de esta unidad

Qué es cada cosa 24

– Display 24

Funciones básicas 24

– Encendido y apagado 24

– Selección de una fuente 24

– Cambio del modo panorámico 24

– Cambio del ajuste del atenuador de

luz 25

Configuración 25

– Cambio del ajuste de la imagen 25

– Selección del formato de vídeo 26

Conexión e instalación

Conexiones 27

– Diagrama de conexión 29

Instalación 30

– Montaje con carcasa 30

– Retirada de la unidad de display 30

Información adicional

Uso correcto del display 31

– Manejo del display 31

– Pantalla de visualización de cristal

líquido (LCD) 31

– Mantenimiento del display en buen

estado 32

– Tubo fluorescente pequeño 32

Especificaciones 33

Es

17

Español

Contenido

INSTRUCCIONES DE

SEGURIDAD IMPORTANTES

Lea todas estas instrucciones sobre el display

y consérvelas para consultarlas en el futuro.

1 Lea todo este manual con suma atención

antes de utilizar el display.

2 Conserve este manual a mano para que

pueda consultar los procedimientos de

operación y la información sobre seguri-

dad cuando sea necesario.

3 Preste mucha atención a todas las adver-

tencias que se indican en este manual y

siga las instrucciones con cuidado.

4 No permita que otras personas utilicen

este sistema hasta que hayan leído y com-

prendido las instrucciones sobre el funcio-

namiento del aparato.

5 No instale el display en un lugar que (i)

pueda obstaculizar la visión del conduc-

tor, (ii) pueda alterar el funcionamiento de

los sistemas operativos o los dispositivos

de seguridad del vehículo, en particular

las airbags y los botones de luces de se-

guridad o (iii) pueda afectar la capacidad

del conductor para manejar el vehículo de

manera segura.

6 Al igual que cualquier accesorio ubicado

en el interior del vehículo, el display no

debe desviar su atención de la conducción

segura del vehículo. Si tiene dificultades

para utilizar el sistema o leer el display,

aparque en un lugar seguro antes de

hacer algún ajuste.

7 Recuerde usar siempre el cinturón de se-

guridad cuando conduzca el vehículo. En

caso de accidente, las lesiones pueden ser

mucho más graves si el cinturón de segu-

ridad no está debidamente abrochado.

ADVERTENCIA

! No trate de instalar o reparar el display

usted mismo. L a instalación o la repara-

ción del display por parte de personas sin

cualificación y experiencia en equipos

electrónicos y accesorios para automóvi-

les puede ser peligrosa y puede exponerle

al riesgo de sufrir una descarga eléctrica u

otros peligros.

ADVERTENCIA

! NUNCA instale este display en un lugar en

el que sea visible para el conductor. De lo

contrario, el conductor podría distraerse

con las imágenes mientras el vehículo está

en movimiento.

! La utilización de este display está sujeta a

todas las leyes gubernamentales al respec-

to de la ubicación o el uso.

! PIONEER no acepta ninguna responsabili-

dad por cualquier tipo de problemas, daños

o pérdidas incurridas como resultado de un

uso inadecuado del display o la violación

de cualquier ley gubernamental.

Para garantizar la conducción

segura del vehículo

ADVERTENCIA

! Para evitar el riesgo de accidente y la posible

violación de las leyes pertinentes, las unida-

des de display trasero no deben ubicarse en

un lugar que distraiga la atención visual del

conductor.

! El display está diseñado únicamente para su

uso en los asientos traseros. NUNCA instale

el display en un lugar que permita al conduc-

tor ver imágenes mientras conduce.

Precauciones

Es

18

Sección

01

! En algunos países o estados, puede ser ilícita

la visualización de imágenes en un display

dentro de un vehículo, incluso por otras perso-

nas que no sean el conductor. En los casos en

que resulten aplicables, estas normas deben

respetarse y no deben usarse las unidades de

display.

Al utilizar un display conectado

con la salida VIDEO OUTPUT

La salida VIDEO OUTPUT de esta unidad sirve

para conectar un display que permita a los pa-

sajeros de los asientos traseros ver un DVD o

un programa de TV.

ADVERTENCIA

NUNCA instale el display trasero en un lugar

que permita al conductor ver un DVD o un pro-

grama de TV mientras conduce.

Para evitar la descarga de

la batería

Asegúrese de que el motor del vehículo esté

en marcha cuando utilice esta unidad. En

caso contrario, se podría agotar la batería.

Precauciones

Es

19

Sección

Español

01

Si desea deshacerse de este producto, no lo

mezcle con los residuos generales de su

hogar. De conformidad con la legislación vi-

gente, existe un sistema de recogida distinto

para los productos electrónicos que requieren

un procedimiento adecuado de tratamiento,

recuperación y reciclado.

Las viviendas privadas en los estados miem-

bros de la UE, en Suiza y Noruega pueden de-

volver gratuitamente sus productos

electrónicos usados en los centros de recolec-

ción previstos o bien en una tienda minorista

(si adquieren un producto similar nuevo).

En el caso de los países que no se han men-

cionado en el párrafo anterior, póngase en

contacto con las autoridades locales a fin de

conocer el método de eliminación correcto.

Al actuar siguiendo estas instrucciones, se

asegurará de que el producto eliminado se so-

meta a los procesos de tratamiento, recupera-

ción y reciclaje necesarios, evitando de este

modo efectos potencialmente negativos en el

entorno y la salud humana.

Acerca de esta unidad

PRECAUCIÓN

! No permita que esta unidad entre en contacto

con líquidos. Eso podría producir una descar-

ga eléctrica. Además, el contacto con líquidos

puede causar daños en esta unidad, humo y

recalentamiento.

! Conserve este manual a mano para que

pueda consultar los procedimientos de opera-

ción y las precauciones cuando sea necesa-

rio.

! Mantenga siempre el volumen lo suficiente-

mente bajo como para que pueda escuchar

los sonidos que provienen del exterior del ve-

hículo.

! Proteja esta unidad de la humedad.

Visite nuestro sitio Web

Visítenos en el siguiente sitio:

! Registre su producto. Conservaremos los

datos de su compra archivados para que

pueda consultar esta información en caso

de que deba efectuar un reclamo a la com-

pañía de seguros por pérdida o robo.

! En nuestro sitio Web ofrecemos la informa-

ción más reciente acerca de Pioneer

Corporation.

En caso de problemas

En caso de que este producto no funcione co-

rrectamente, comuníquese con su concesio-

nario o el Servicio técnico oficial Pioneer más

próximo a su domicilio.

Para proteger la pantalla LCD

! Mantenga el display fuera del alcance de la

luz solar directa cuando no se utilice esta

unidad. La exposición prolongada a la luz

solar puede causar un fallo de funciona-

miento de la pantalla LCD como conse-

cuencia de las altas temperaturas

generadas.

Antes de comenzar

Es

20

Sección

02

Страница загружается...

Pioneer AVD-W7900 Руководство пользователя

Похожие модели бренда

Модели других брендов