LED TV/
Телевизор цветного
изображения c
жидкокристаллическим
экраном
TF-LED28S16T2
Instruction manual
Руководство по
эксплуатации
Table of contents
2
Table of contents
Table of contents
Before you start
Utilization of the product
Important safeguards
Installation
Wall mounting
Stand installation
Connection
Connection
Outdoor antenna connection
Other connections
Operation
Control elements
Remote controller
Changing the battery
General operations
Teletext operations
OSD operation
Channel installation
Picture setting
Sound setting
Lock settings
Timer settings
Option settings
USB operation
General information
File playback
CI information
General information
Troubleshooting
Causes of interference
Accessories
Specifications
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read
this manual carefully before connecting, operating and/or adjusting the product and keep
the manual for reference in the future.
2
3
3
3
4
4
4
5
5
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
13
13
13
13
15
15
15
16
16
Before you start
3
Before you start
If you want to dispose of this product, do not mix it with general household waste. There
is a separate collection system for used electronic products in accordance with legislation
that requires proper treatment, recovery and recycling.
Please contact your local authorities for the correct method of disposal. By doing so,
you will ensure that your disposed product undergoes the necessary treatment, recovery
and recycling and thus prevent potential negative effects on the environment and human
health.
Utilization of the product
Important safeguards
• Before plugging the power cord make sure
that the voltage designation of the LED TV
corresponds to the local electrical supply.
• Please unplug the power cord from the AC
outlet and contact a service center for repair if
the following occurs: any obvious abnormality
appears in the unit, such as smoke, peculiar
smell or strange sound; liquid has been spilled or
other objects have fallen into the unit; no picture
or sound; cover or panel is broken; although you
have operated the unit following the operating
instructions, it still cannot work normally.
• This unit can be connected to a power
supply outlet without the third ground contact
as well as with a ground contact.
• Always disconnect the power cord and
antenna during a storm.
• Do not fix the power cord with a metal nail.
• When connecting or disconnecting cables
to or from TV terminals, make sure the power
is switched off.
• Unplug the power cord from the AC outlet;
also unplug the signal cables from the input
ports when the unit is unused for long periods
of time.
• When pulling the plug, always hold the
wide slot, do not touch the metal part, and do
not destroy, refit, twist, pull or burn the power
cord.
• Please contact the service center
immediately if you found that the cable core is
bare or has been broken.
• Please replace the AC outlet if the metal
bolt cannot be inserted into the power socket
completely or it cannot be fastened even when
it was pushed in, otherwise, any accidents of
shocks and fires would happen.
• Never touch the antenna lie or power plug
if it stars to thunder.
• Do not touch the power plug with wet
hands.
• Do not use any non-rated power socket
with numerous devices jointed on one power
socket or cable device. The wire of non-
designated capacity may cause the fire due to
the generation of heat.
• All instructions must be read and
understood well before you operate the unit.
Heed all warnings and follow all instructions.
• Please use the accessories provided
by the manufacturer. Using inadequate
accessories may result in accidents.
• Please adjust the product through the
panel buttons or the remote controller, do
not remove the cover or attempt to service
the product by yourself. Do not disassemble
back cover and do not make maintenance by
yourself to avoid the electric shock.
• Over-pressing the panel may destroy the
product.
• Do not place the product on an unstable
cart, stand surface, tripod, bracket, or table.
The product may fall, causing serious accidents
as well as the damage to the product.
• Please place the product on a flat surface
in a well-ventilated location. Keep it away from
Before you start
4
4
Before you start
the burning-light, direct sunlight, vibration,
high-temperature and humidity.
• Do not place any vase, potted plant, cup,
medicine and any container with water on this
product. If the liquid is spilt, it may cause the
fire, electric shock or breakdown.
• Do not install it at the place on the strong
magnetic field or current field. It may cause
break down. This equipment may be observed
deterioration of the picture by electromagnetic
radiation in electromagnetic environment.
• Fasten the wheel of the product or shelf
with wheels when installing this product. If it
moves or is tipped over, it may be damaged.
• Do not place any fire source such as
candlelight close to this product or place it on
this product. If it is tipped over or fallen down, it
may cause damage or fire.
• Do not place the unit into closed space
of TV for better ventilation; it can reduce the
product lifetime. Keep a space at least 10 cm
at above, left and right of the TV.
• Please place all the signal cords behind of
rear panel.
• Do not overexert or touch the panel when
you convey the product. Do not transfer the
LED TV up or down display direction.
• Do not transport it with the power cord
connected. If you move this product with the
power cord or the connection cable connected,
the damaged power cord, connection cable
or connection terminal may cause the fire, the
electric shock or breakdown.
• 2 persons or more shall transport the
device, which is heavier than 18 kg. If you drop
or tip over the device, it may damage it.
• The temperature of the product’s body
becomes a little higher after a long period use.
This phenomenon indicates that heat exchange
in normal working mode, thus please do not
let children or anyone who is sensitive of
temperature to touch.
• Please allow at least a 5 hour wait at room
temperature before switching on the power
after transpoting or storing the TV at below
zero temperatures.
All images provided herein are schematic
drawings and may differ from of real objects.
Installation
Wall mounting
For wall mounting the back panel of this unit
is equipped with a VESA slot. Please use the
standard fixed 100x100 VESA wall mounting
bracket and follow its installation instructions
accordingly. The wall-mounting bracket is not
included and should be acquired separately. Do
not use tilting wall mounting brackets or try to
tilt this TV on the bracket. Manufacturer is not
responsible for improper mounting resulting in a
damage to the unit.
Stand installation
Cover a flat stable surface with a soft cloth.
Place the TV unit facedown on the cloth. Insert
double support legs and fix them with 4 screws
as shown below.
WARNING
In order to avoid damage, make sure
to secure the unit on the wall
according to the wall mounting
instruction.
Before you start
5
5
Before you start
Connection
Outdoor antenna connection
Use 75Ω cable plug or 300-75Ω impedance
converter to plug in antenna input terminal on
the rear of the cabinet.
Other connections
• Connect the audio sources (Including
DVD, VCDR, CAMCORDER and PC) to the
‘Audio in’ socket.
• Connect the video source to the AV
IN jack by RCA cable (it is shared with the
component jack).
• Component input is intended to receive
component video signal from the external
device. Connection is made with the help of a
special component cable. To receive audio sigl-
nal for component video, please use the audio
input of this unit.
• Plug the power cable in the electric outlet,
making sure the current voltage is supported.
• When using the LED as a computer
screen, connect the PC to the VGA jack from
the monitor by the relevant cable (not included).
• If the video source has a HDMI output
jack, you can connect the signal to the
monitor by the HDMI cable (not included).
Use the HDMI-2(MHL) input to connect your
smartphone via a special cable (not included)
to see the digital content on the TV screen.
• Coaxial SPDIF output is intended for
transmitting multi-channel sound to an external
decoder (e.g. in 5.1-CH format). Coaxial cable
should be used for connection.
• PCMCIA slot is used for CI modules that
are obtained from your digital TV provider.
Please note that AV and component
input (YPbPr) share the same socket so make
sure that if the one or the other input is used,
you choose the corresponding source signal
(press the SOURCE button).
75 Ohm co-axis cable
TVRF antenna jack
Antenna cable connector
Operation
6
6
Operation
Control elements
1. IR sensor/power indicator
2. Button panel:
PRO + button
POWER/PRO - button
VOL + button
VOL - button
MENU button
3. AC IN power input
4. HDMI1 input
5. Audio input
6. Component/AV input
7. VGA input
8. TVRF antenna socket
9. SPDIF coaxial output
10. USB port
11. CI (PCMCIA) slot
12. HDMI2 (MHL) input
2
3 4 5 6 7 8
9
10
11
12
1
Operation
7
7
Operation
Remote controller (RC)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1. SOURCE button
2. Number buttons
3. ECO button
4. MENU button
5. Cursor (UP/DOWN/LEFT/RIGHT) buttons/
OK button/ZOOM-/ZOOM+ buttons
6. OPTION button
7. VOL+/VOL- buttons
8. MUTE button
9. TEXT button
10. SUBTITLE button
11. Red button
12. Green button
13. POWER/STANDBY button
14. GUIDE button
15. EXIT button
16. RETURN button
17. INFO button
18. CH+/CH- buttons
19. TV button
20. LIST button
21. LANG/Blue button
22. Yellow button
Changing the battery
1. Remove the battery compartment cover
on the back of the RC.
2. Insert the batteries into the battery
compartment making sure that the correct
polarity is observed.
3. Install the cover back.
• Use two AAA batteries for the RC. The RC
should be pointed at remote sensor within 8
meters and within 30 degrees at the left or the
right side.
• Take the battery out of the RC if it is not
used for a long time.
• Do not mix new and used batteries or
different types of batteries. Weak batteries can
leak and severely damage the RC.
• Do not expose the RC to shock, liquids,
and do not place it in an area with high
humidity.
CAUTION!
Incorrect installation of the batteries may
lead to an explosion.
Please replace used batteries with the
batteries of the same or comparable type.
1 2 3
Operation
8
8
Operation
General operations
• Connect the terminal of the power cord
to the power cord input of the TV (the position
of the input is given in paragraph Connection
above). Connect the plug of the power cord to
the power supply outlet, the power indicator will
light showing that the unit is in standby mode.
To switch on the unit, press POWER button on
the panel or on the RC; when the TV is on, the
power indicator is off. Press POWER button
again to switch the unit to the standby mode,
the power indicator will light up. To switch off
the unit completely, disconnect the power cord
plug from the power supply outlet.
• Press VOL- button on the unit or on
the RC repeatedly to decrease the volume;
press VOL+ button on the unit or on the RC
repeatedly to increase the volume.
• Press RETURN button on the RC to select
from the present channel and the previously
displayed channel.
• Press MUTE button to mute sound, press
this button again or adjust volume to resume
sound.
• In TV mode press CH+/CH- buttons on the
RC or PRO+/PRO- on the unit to select previous
or next channel; or press number buttons to
enter a channel number directly.
• Press INFO button to display the preset
TV channel information.
• Press ZOOM+/- buttons repeatedly to
select a screen format. Available aspects may
differ for different signal sources.
• Press SOURCE button, then press cursor
buttons on the RC to select a source from
available source list: TV => AV => DTV =>
YPbPr => PC => HDMI1 => HDMI2 => USB;
You can press TV button to access TV source
mode directly.
• Press ECO button on the RC to enter the
energy saving mode.
• Press GUIDE button to access the
electronic program guide in DTV mode.
• Press LIST button to enter the channel list.
• Press SUBTITLE button to enter the subtitle
language menu in DTV mode.
• Press LANG button to enter the audio
language menu in DTV mode.
TELETEXT operations (option)
• Select the TV source mode. Then press
CH-/CH+ buttons to select TV channel in order
to pick up the picture signal of Teletext.
• Teletext button functions are as follows:
TEXT: Press this button to enter into Teletext
mode. Follow the guides on screen and use
the color buttons to navigate the Teletext.
Red/Green/Yellow/Blue buttons: Press
these 4 color buttons to access directly to
corresponding color page displayed at the
lower parts of teletext screen.
Operation
9
9
Operation
OSD operation
1. Press MENU button to enter the setting
menu displayed on the screen.
2. Press LEFT/RIGHT cursor buttons on the
RC to select setting page.
3. Press OK button on the RC to go to the
parameter list.
4. Press UP/DOWN cursor buttons on the
RC to select a parameter to adjust.
5. Press LEFT/RIGHT cursor buttons on the
RC to adjust the selected parameter.
6. Press MENU button to return to the
previous menu page. Press EXIT button on the
RC to quit the menu.
Some menu items may be in grey color,
in this case they are not adjustable. Pictures
of OSD menu are for reference only; they may
differ from the real screens.
Channel installation
Channel install
Automatic search
Automatic update
Antenna manual installation
Clean channel list
• Automatic Search: this option allows the
TV to search for, find and store all the available
analog and digital channels. Follow all the
steps in turn specified hereafter:
1. Press the Menu button to display the main
menu, and select Setup>Channel install, then
press the OK or right direction button to display
its options.
2.Select Automatic search, then press the
OK or right direction button to enter.
3. Select Digital & Analogue (or Digital or
Analogue), then press the OK or right direction
button to start the automatic search process.
The search may take a few minutes. During the
process, you can press Menu or Exit to abort
halfway.
4. Once the automatic search ends, press
the Menu button to return to the last step or
press OK to restart your channel search.
5. After the automatic search, channels
are arranged in a preset order. You can skip
channels, modify the preset order or rename
channels, select Setup >Organiser and press
the OK or right direction button to enter.
Skipping channels: if a channel was stored
twice or its reception is poor, you can simply
skip it. The skipped channels can not be
selected by pressing the CH+ /CH- buttons.
Select the Channel skip option and press the
OK or right direction button to display Channel
skip menu. Press the up or down direction
button to select a channel and press the OK
button to check the box.
Sorting channels: swaps two channels
position.
1. Select the Channel sort option and press
the OK or right direction button to display
Channel sort menu.
2. Press the up or down direction button to
select a channel, and press OK to confirm.
3. Press the up or down direction button to
select your swapped channel, and press OK to
swap the two channels.
Edit channels: select the Channel edit option
and press the OK or right direction button to
display Channel edit menu. Press the up or
down direction button to select a channel you
want to edit, then press the OK button to enter.
Press the up or down direction button to select
Channel number or Channel name, using
the digit keys to edit the channel number or
channel name, finally press OK to confirm.
When you have finished press Menu to return,
or press Exit to close the menu.
• Automatic Update: This allows you to
update all available channels, without altering
the sorting of existing channels.
1. Display the Channel install menu, press
the up or down direction button to highlight
Automatic update option.
2. Press the OK or right direction button
to start to update the channels. To stop the
update process, press the Menu button.
3. When the search is completed, press
Menu to return, or press OK to restart.
Operation
10
10
Operation
• Analogue Manual scan:
1. Display the Channel install menu, press
the up or down direction button to highlight
Analogue manual scan, press the OK or right
direction button to enter.
2. Press the up/down/left/right direction and
number or OK button to search, fine tune or
store the channel.
3. Press Menu to return to the previous
menu or press Exit to close the menu.
• Antenna Manual Installation: Allows
you to start manual searching the available
channels from the current frequency or any
frequency you input.(Only for digital channels)
1. Display the Channel install menu, press
the up or down direction button to highlight
Antenna manual installation, press the OK or
right direction button to enter.
2. Press OK to start search from the
current frequency, or use digit keys to input a
frequency, then press OK to start search.
3. When the search is completed, press
Menu to return, or press OK to restart.
• Clean Channel List: Allows you to remove
all the searched channel from the channel list.
1. Display the Channel install menu, press
the up or down direction button to highlight
Clean channel list, press the OK or right
direction button to enter.
2. Press the left or right direction button to
select OK, then press OK to confirm to clean
the channel list.
Picture setting page
Picture
Picture preset
Brightness
Contrast
Saturation
Sharpness
Color Temperature
Screen Mode
Auto Format
ECO Settings
Advanced Settings
Reset
• Picture preset: Standard/Dynamic/Studio/
Personal/Movie.
• Brightness, Contrast, Saturation,
Sharpness: adjust the picture parameters.
• Color temperature: Select color
temperature mode of the picture - Normal/
Warm/Cool/Customer.
• Screen Mode: Select the screen aspect
ratio.
• Auto format: toggle on and off the
automatic format of the picture in TV and AV
modes.
• ECO Settings: select one of the energy
saving modes.
• Advanced Settings: select and edit
more advanced picture settings such as noise
reduction, dynamic contrast and others.
• Reset: revert all picture settings to factory
default values.
Sound setting page
Sound
Sound preset
Balance
Audio Description
Wide Stereo
Sound Type
Auto Volume Control
• Sound preset: Off/Rock/Pop/Live/Dance/
Techno/Classic/Soft/Personal. You can also
adjust frequency ranges yourself to achieve
more personalized sound.
• Balance: adjust balance between left and
right speaker.
• Audio Description: this is an auxiliary
audio function that provides an additional audio
track for visually challenged persons. Users
can turn the Audio Description On or Off and
control the volume.
• Wide Stereo: toggle the wide stereo effect
on or off.
• Sound Type: select a sound type from
the list.
• Auto Volume Control: toggle auto-volume
Operation
11
11
Operation
control on/off. Volume automatically remains
on the same level of volume if you change
programmes. Because each broadcasting
station has its own signal conditions, volume
adjustment may be needed every time when
the channel is changed. This feature allows
users to enjoy stable volume levels by making
automatic adjustments for each program.
Lock settings
Lock
Channel lock
Parental rating
Input lock
Front panel lock
Installation lock
Max volume
Change password
Clean all
• Channel lock: this option allows you to
lock a certain TV channel. Use the up or down
direction button to select a certain
TV channel you want to lock, then press the
OK button to lock. To unlock, use the same
operation.
• Parental rating: this feature can pre-
vent children watching adult’s TV programs,
according to the rating limit set. This function
appearance according the information from
broadcasting station. Therefore if the signal
has incorrect information, this function does
not operate.
• Input lock: lock/unlock input from external
sources.
• Front panel lock: lock/unlock buttons on
the TV set.
• Installation lock: lock/unlock access to
the channel installation menu.
• Max volume: set the maximum volume
level for programs.
• Change password: this option allows
you to change the password. Press the OK or
right direction button to enter, then press the
number buttons to enter the new password
twice.
• Clean all: unlock all locked channels and
restrictions.
Timer settings
Timer
Time zone
Clock
Sleep timer
Auto standby
• Time zone: select the local time zone.
• Clock: press OK or right direction button
to enter the clock submenu:
Auto synchronization: use the left or right
direction to select On or Off. If On selected,
the TV will get the time automatically from DTV
signals, and the Time item cannot be adjusted.
If you select Off, you should set date and time
at Date and Time item. Highlight Date or Time,
use the left or right direction button to select
input space, enter the current date or time by
using the digit keys.
If Off is selected, the time set in Time
option will not be memorized when turning on
the TV next time, and the TV ‘s time will start
from the default.
Power on timer: use the left or right direction
button to select Once, Daily or Off. If you select
Once or Daily, you should set a time period
after which the TV automatically switches on
at Timer below this item. Highlight Timer, use
the left or right direction to select input space,
enter the on time using the digit keys.
Power on channel: press the OK or the
right direction button to display its submenu.
Highlight Select, use the left or right direction
button to select Last status, the power on
channel will be the last channel you watched
before powering off.
Or you can choose User select, then press
the up or down direction button to select the
channel you want to watch when the TV is
turned on automatically next time, and press
OK to confirm.
Power off timer: use the left or right direction
Operation
12
12
Operation
button to select Once, Daily or Off. If you select
Once or Daily, you should set a time period
after which the TV automatically switches to off
at Timer below this item. Highlight Timer, use
the left or right direction to select input space,
enter the off time using the digit keys.
• Sleep timer: sets a period of time after
which the TV set goes into standby mode.
Use the left or right direction button to set the
period (120 minutes maximum). To disable this
function, select Off.
• Auto standby: use left and right direction
buttons to set up the auto standby time.
Options settings
Options
Subtitle
SPDIF type
T-link
Common interface
Location
Decoding page language
Digital teletext language
Software update
• Subtitle: this enables subtitle for digital
TV channels. Select Subtitle option, press
the OK or right direction button to display its
submenus:
Subtitle: press the left or right direction
button to turn the subtitles on or off.
Subtitle type: press the left or right direction
button to select a subtitle type. You can
select Hearing impaired to display the hearing
impaired subtitle with your selected language.
• SPDIF type: connect to an audio device
through the SPDIF output. Select Options >
SPDIF type. Select a proper sound type from
the list for digital programs.
- If the current program outputs sound in
Dolby D format, then either PCM or Dolby D
can be selected.
- If the current program does not output
sound in Dolby D format, only PCM can be
selected. Otherwise no sound will be output.
- Select Off to turn off the audio output from
the Audio Device connected to the SPDIF
output.
The options you may choose depend
on the programme you are watching. If you
select PCM and the sound output is prior to the
picture, you can select SPDIF delay from the
Options menu and press the left or right
direction button to adjust the delay time to
synchronize the sound with the picture.
• T-link: to search for CEC devices
connected to the HDMI inputs in your TV and
enable one-touch play and one-touch standby
between CEC devices.
Enable or disable T-Link
1. Press Menu on the remote control, then
select Options > T-Link.
2. Press the left or right direction button to
select On or Off.
Use one-touch play: one-touch play enables
you to press the play button on, for example,
your DVD remote control. This starts playback
on your DVD device and automatically
switches your TV to the correct source,
displaying DVD content.
Use System standby: system standby
enables you to press the standby button on,
for example, your TV remote control. This
switches your TV and all connected HDMI
devices to standby mode.
• Common interface: select this option
to enter the common interface submenu.
Only available when a CI card inserted in the
PCMCIA slot in DTV mode.
• Location: use the left or right direction
button to select Home or Shop mode. Home
mode is the default. If Shop mode selected,
the picture will be displayed in Dynamic mode.
In Shop mode, you can adjust the picture
mode, but when turning on the TV next time,
the Picture preset will restore to Dynamic
mode, and a prompt about Shop mode will
appear.
• Digital page language: Select the
preferred language for digital TV pages.
• Digital teletext language: Select the
preferred Teletext language.
• Software update: Select this option for a
software update and follow the instructions on
screen.
Operation
13
13
Operation
USB operation
General information
USB file systems supported: FAT32. 2.0
USB version is supported. Maximum capacity
1 TB. For correct and satisfactory operation,
licensed USB devices of well-known brands
should be used with this unit. Avoid using
USB devices of unknown brands. Playback
of images and music of only JPEG and MP3
format is supported. The output capability of
the USB port is 1 A.
• This unit supports playback of video files
with AVI, TS, MP4, MKV, MOV extension,
with video codecs H264/AVC, H263, Divx,
MPEG1/2/4 and audio codecs PCM, DD(AC3),
MP3, AAC.
The above list of extensions and codecs
is for information only and is not a guarantee
that all files having the above extensions and
codecs should be read by this unit.
• Some AVI files cannot be played due to
their parameters and recording conditions.
Video files with AVI extension exceeding 2 GB
in size may be played partially.
According to the USB 1.1/2.0 Standard,
usage of a USB device with power current
consumption exceeding 500 mA is not
recommended without supplementary power
supply. Failure to use supplementary power for
connected USB drives with power consumption
exceeding this value as well as defective
USB drives may cause mechanical or thermal
changes of elements of this unit as well as
failure of internal elements of the USB port.
Such damages are not warrantee cases.
Warning: usage of external USB drives
containing BIN files in the root directory may
cause malfunction of the unit or damage to the
software.
File playback
Insert a USB into the USB jack. Press MENU
button, select Media option and press OK
button. The screen will show USB playback
menu:
Media center
Photo
Music
Video
• Video file playback: Select Video item
and press OK button. Press cursor buttons
to select a file and press OK button to start
playback. During playback press MENU but-
ton to show playback menu in which you can
select an operation by LEFT/RIGHT cursor
buttons and perform this operation by press-
ing OK button. The operations include Play/
Pause, Backward, Forward, Prev., Next, Stop,
Repeat Mode, AB Repeat setting, Playlist,
Info., Slow Forward, Step Forward, Goto
Time, Brightness, Contrast, Zoom out, Zoom
in, Scale, Move View. To exit video playback
press EXIT button.
• Image file playback: Select Photo item
and press OK button. Press cursor buttons
to select a file and press OK button to start
playback. During playback press MENU but-
ton to show playback menu in which you can
select an operation by LEFT/RIGHT cursor
buttons and perform this operation by pressing
OK button. The operations include Play/Pause,
Prev., Next, Stop, Rotate Right, Rotate Left,
Music(on/off), Musiclist, Zoom in, Zoom out,
Repeat Mode, Capture and Info. To exit photo
playback press EXIT button.
• Audio file playback: Select Music item and
press OK button. Press cursor buttons to select
a file and press OK button to start playback.
During playback press MENU button to show
playback menu in which you can select an
operation by LEFT/RIGHT cursor buttons and
perform this operation by pressing OK button.
The operations include Play/Pause,Backward,
Forward, Prev., Next, Stop, Repeat Mode, Mute,
Playlist, Info. and Goto Time. To exit music
playback press EXIT button.
CI Information
(only in DTV mode): This function enables
you to watch some encrypted services (pay
services). Please insert a CI card into the
Operation
14
PCMCIA slot according to the arrow on the CI
card.
The function can only be available when
CI card is present.
• It is possible for you to change CI
(Common Interface) menu screen and service
by consulting your dealer.
• Please do not insert or pull out the CI card
when power on. During initialization of the CI
card, please don’t operate the TV.
• Do not insert or pull out the CI card
frequently so as to avoid any damages of the
TV and the CI card.
• If there is no picture and/or sound with the
CI+ CAM module inserted, please contact the
customer support of the service provider.
Operation
General information
15
Troubleshooting
Below is a table describing simple measures that can help you eliminate most problems likely
to emerge when this unit is in use. If below measures do not help, turn to a service center or to the
nearest dealer.
Symptom Cause Solution
No picture, no
sound, and no
indicator light
The power cord is not plugged in.
Contrast, brightness, color and
volume are all in the minimum value
or TV is in mute mode.
Plug the power cord in.
Alter the value of contrast,
brightness, color and volume.
Picture and
sound with
abnormity
Contrast and color are set improperly.
Color system is set improperly.
Sound system is set improperly.
Set the value of Contrast and color
properly.
Set the sound system properly.
Picture is spotted
or with snow
Signal source is low-grade or the
signal is in a lower quality.
Use the qualified signal cord.
The picture in
VGA mode is
abnormal
The PC settings may be improper. Check and set the resolution
parameters of your PC.
Picture is split in
two parts
Either AV or component input is
chosen as a source.
Choose the correct source mode
depending on the cable you use (AV
or component)
Blue background No video signal or the signal cord is
improperly/not connected.
Connect the signal cord properly.
No sound No audio signal or the signal cord is
improperly/not connected.
Connect the audio signal cord
properly.
Set the sound system properly.
The RC does not
work
Batteries are improperly installed or
exhausted.
Make sure the positive and the
negative polarities are correct.
Reattach the battery lid.
Replace the batteries.
Causes of interference
Incorporated in your TV receiver are the most up-to-date devices to eliminate interference.
Local radiation however, can create disturbances, which visibly affect your picture. Proper
installations, a good aerial are your best safeguards against these disturbances.
• RF INTERFERENCE: Moving ripples across the screen are caused by nearby transmitting or
receiving short-wave radio equipment.
• DIATHERMY: Herringbone pattern and partial picture loss can result from the operation of
diathermy equipment from a nearby doctor’s surgery or hospital.
• SNOW: Weak TV signals from long distant stations result in an instead picture and give the
effect of falling snow. An antenna adjustment or antenna amplifier may be needed.
• GHOST: Multiple image, caused by TV signals reflected back from surrounding buildings,
hills, aircraft, etc. is minimized by correct aerial positioning.
• CAR IGNITION: Nearby cars and electrical motors can cause small streaks across the picture
or make the picture roll.
General information
General information
16
14
General information
Accessories
Specifications
Size (diagonal)
28” (70 cm)
Response time 6.5 ms
Resolution
1366 x 768
Aspect ratio 16:9
View angle (Horizontal/Vertical) 178
o
/178
o
Color system PAL, SECAM
Sound system B/G, DK
NICAM Stereo 2 x 5 W
Digital coaxial audio output (SPDIF) +
Component video in +
AV in (paired with Component) +
USB port +
VGA +
HDMI x2
MHL function +
DVB-T/DVB-T2/DVB-C signal reception +
PCMCIA slot (CI, CI+ support) +
Russian and English OSD +
Progressive scan +
Digital comb filter +
Sleep timer +
Number of channels 1500
Electric shock protection class
Nominal voltage range:
Unit dimensions: with stand
without stand
Net weight
II
~110–240 V; 50/60 Hz;
645 x 431 x 197.5 mm
645 x 389 x 84 mm
3.6 kg
The LCD panel is a high technology product with many thin film transistors that can
give you a fine picture details. Occasionally, a few non-active pixels may appear on the screen
as a fixed point of blue, green, red, black or white, please note that this does not affect the
performance of your LCD TV.
Warning: For the sake of improvement, unit specifications may be subject to change without
prior notice.
1. LED TV 1 pc
2. Remote controller 1 pc
3. Battery 2 pcs
4. Stand legs 2 pcs
5. Screw 4 pcs
6. Power cable 1 pc
7. AV-cable 1 pc
8. Consumer information 1 pc
9. Warranty card 1 pc
10. Instruction manual 1 pc
Operating conditions
Ambient temperature
Relative humidity
Atmospheric pressure
from 5 to 35
o
C
from 45 to 75%
from 86 to 106 kPa
(650-800 mm Hg)
Содержание
17
15
Содержание
Уважаемый покупатель!
Благодарим Вас за покупку нашего изделия. Чтобы понять, как правильно и безо-
пасно пользоваться приобретенным устройством, рекомендуется тщательно изучить
настоящее руководство перед подключением и эксплуатацией изделия. Сохраняйте
руководство для использования в будущем.
Содержание
Перед началом эксплуатации
Утилизация изделия
Меры предосторожности
Установка
Крепление на стену
Установка на подставку
Подключение
Подключение
Подключение внешней антенны
Прочие подключения
Управление устройством
Элементы управления
Пульт дистанционного управления
Установка батареек
Общие операции
Операции с телетекстом
Экранное меню
Установка каналов
Настройка изображения
Настройка звука
Настройка блокировки
Настройка таймера
Настройка опций
Операции с USB
Общая информация
Воспроизведение файлов
Интерфейс CI
Общая информация
Руководство по устранению
неисправностей
Источники помех
Комплект поставки
Технические характеристики
17
18
18
18
20
20
20
21
21
21
21
22
22
23
23
24
24
25
25
26
27
27
28
28
29
29
30
31
32
32
33
33
34
Перед началом эксплуатации
18
16
Перед началом эксплуатации
Если вы желаете утилизировать данное изделие, не выбрасывайте его вместе с
обычным бытовым мусором. Существует отдельная система сбора использованных
электронных изделий в соответствии с законодательством, которая предполагает
соответствующее обращение, возврат и переработку.
Обращайтесь в органы местного управления за инструкциями по правильной
утилизации продукта. Тем самым Вы обеспечите утилизацию Вашего изделия с
соблюдением обязательных процедур по обработке, утилизации и вторичной пере-
работке и, таким образом, предотвратите потенциальное негативное воздействие на
окружающую среду и здоровье людей.
Утилизация изделия
Меры предосторожности
• Перед подсоединением кабеля питания
к телевизору убедитесь, что напряжение
устройства соответствует напряжению
электрической сети.
• Пожалуйста, извлеките шнур пита-
ния из розетки и свяжитесь с сервисной
службой в следующих случаях: если в
устройстве имеются явные неисправности,
например, из него идет дым, чувствуется
специфический запах или слышен неха-
рактерный звук; если внутрь устройства
попала жидкость или посторонние предме-
ты; если нет изображения или звука; если
поврежден корпус или панель; если Вы
пользуетесь устройством согласно инструк-
ции, но оно не работает должным образом.
• Данное изделие может подключаться
к розетке питания как без заземляющего
третьего контакта, так и с заземляющим
третьим контактом.
• Во избежание поражения электриче-
ским током защищайте шнур питания от
возможного нажатия на него или защемле-
ния, особенно рядом с разъемами.
• Не закрепляйте шнур питания метизами.
• Если Вы не пользуетесь устройством
длительное время или в случае грозы,
обязательно отключайте шнур питания из
розетки, а также отключайте все сигналь-
ные кабели от входных разъемов.
• При подключении или отключении
кабелей обязательно удостоверьтесь в том,
что питание устройства выключено.
• При отключении вилки из розетки всег-
да держитесь за утолщение на вилке, не
касайтесь металлических частей, не тяните
за шнур, не ломайте и не перегибайте его,
не ремонтируйте, не перекручивайте и не
нагревайте.
• Немедленно свяжитесь с сервисным
центром, в случае если имеются какие-либо
неисправности шнура питания, в нем оголи-
лись жилы или он поврежден.
• Замените сетевую розетку, если в
нее невозможно вставить вилку или вилка
плохо закрепляется в розетке. Иначе могут
возникнуть неисправности, или произойти
несчастные случаи или возгорания.
• Не прикасайтесь к проводам мокрыми
руками.
• Запрещается использование розетки, в
которую подключено несколько устройств.
Перегрузка такой розетки может привести
к пожару.
• Место подключения вилки шнура
питания к сети 220 В должно оставаться
легкодоступным.
• Перед работой с устройством необ-
Перед началом эксплуатации
19
17
Перед началом эксплуатации
ходимо полностью прочитать и понять все
инструкции. Необходимо соблюдать все пред-
упреждения и следовать всем инструкциям,
приведенным в настоящем руководстве.
• Пожалуйста, используйте только реко-
мендованные производителем аксессуары.
Использование других аксессуаров может
привести к неисправностям.
• Пожалуйста, проводите все настройки
и регулировки только с помощью кнопок
на боковой панели или на пульте дистан-
ционного управления. Ни в коем случае не
снимайте заднюю панель и не пытайтесь
самостоятельно проводить техническое об-
служивание устройства, так как существует
опасность поражения электрическим током,
а также возможно возникновение неисправ-
ностей.
• Не устанавливайте устройство на
непрочные или неровные поверхности,
тележки, стойки, треноги, кронштейны
или столы. Устройство может упасть, в
результате чего могут возникнуть неисправ-
ности или произойти несчастные случаи.
Используйте только те приспособления,
которые рекомендованы производителем
или продавцом.
• Пожалуйста, устанавливайте устрой-
ство на горизонтальной поверхности в ме-
стах с хорошей вентиляцией. Не допускайте
воздействия на устройство вибрации, пря-
мого солнечного света, высокой температу-
ры, а также попадания пыли и влаги.
• Не ставьте на устройство вазы, сосуды
с жидкостью. Попадание жидкости внутрь
аппарата может привести к пожару или по-
ломке устройства.
• Не устанавливайте устройство в зоне
магнитных волн. Это может привести к по-
ломке устройства. В зоне электромагнитно-
го излучения может наблюдаться искаже-
ние изображения.
• Не устанавливайте вблизи устройства
источники открытого огня, например, свечи.
В случае их падения устройство может быть
повреждено или может произойти возгора-
ние.
• Установка телевизора в замкнутое
пространство при эксплуатации может со-
кратить срок службы устройства; поэтому
необходимо обеспечить минимальную
дистанцию между LCD-телевизором и
внутренними границами приспособления
под аппарат для нормальной вентиляции
(минимум по 10 см свободного простран-
ства со всех сторон).
• Располагайте кабели позади устрой-
ства. Не закрепляйте их метизами, не пере-
гибайте, не ремонтируйте и не нагревайте.
• При перемещении телевизора не
нажимайте и не касайтесь панели. Не пере-
носите телевизор в положении, при котором
экран направлен вверх или вниз.
• Не перемещайте устройство при под-
ключенном проводе питания или других
подключенных проводах. Повреждение про-
вода питания, подключенный провод или
подключенные устройства могут стать при-
чиной пожара, электрошока или поломки.
• Если устройство тяжелее 18 кг, его
должны перемещать не менее 2 человек.
При падении устройство может повредиться.
• Слишком сильное нажатие на панель
может повредить устройство.
• При длительном использовании может
немного повыситься температура корпуса
устройства. Это явление свидетельствует о
теплоотдаче в нормальном рабочем режи-
ме. Однако не позволяйте детям и людям с
повышенной температурной чувствительно-
стью касаться устройства.
• Время выдержки телевизора при ком-
натной температуре до включения питания
после транспортирования или хранения
при пониженной температуре окружающей
среды должно быть не менее 5 часов.
Все иллюстрации, приведенные в на-
стоящем руководстве, являются схе-
матическими изображениями, которые
могут отличаться от реальных объектов.
Перед началом эксплуатации
20
18
Установка/Подключение
Установка
Крепление на стену
Для крепления на стену на задней стенке
корпуса телевизора имеется два отверстия.
Для установки используйте стандартный
фиксированный настенный кронштейн VESA
100x100 и следуйте инструкциям по его
монтажу и креплению. Кронштейн в
комплект поставки не входит и
приобретается отдельно. Для данной
модели не рекомендуется наклонять
телевизор на кронштейне и ис-
пользовать наклонные модели
кронштейнов. Производитель не несет
ответственно-сти за неправильно
выполненный монтаж, повлекший
повреждение телевизора.
ПРЕДУПРЕЖДЕНИЕ
Во избежание повреждений надежно
закрепите аппарат на стене в
соответствии с требованиями
инструкции по установке.
Установка на подставку
Выберите ровную плоскую горизонталь-
ную поверхность, накройте ее мягкой тка-
нью и разместите на ней корпус телевизора
экраном вниз. Присоедините ножки-под-
ставки таким образом, чтобы отверстия в
подставках и в корпусе телевизора совпа-
дали. Зафиксируйте с помощью 4 винтов.
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/
