Slinex Sonik-7 Cloud Руководство пользователя

Бренд: Slinex

Модель: Sonik-7 Cloud

Тип: Руководство пользователя

SONIK 7 Cloud

Design. Uniqueness. InnovationsDesign. Uniqueness. Innovations

Техническая

поддержка

User manual

1-34

Инструкция по эксплуатации

35-68

Technical support

SONIK 7 Cloud

1REV. 1.0 2

Attention!

As a result of continuous upgrades and functionality improvements, technical

characteristics of the device can be changed without any preliminary declaration.

This manual can contain some inaccuracy or misprint. The owner reserves the right to

make corrections to the information described in the user manual and device package.

The last revision of this manual is available on www.slinex.com

Safety instructions

Read and keep that manual.

The device installation process should be carried out by the qulied specialists.

Use the device from –10 ˚C to +55 ˚C, always keep it within that temperature range.

Installation surface should be free from vibration and impact inuence.

Keep this device far from open sources of heat, such as radiators, heaters, and ovens.

The device can be installed near other electronic equipment in case if the temperature of the environment

does not exceed previously mentioned range.

The device should be protected from the direct inuence of the natural phenomena, such as direct

sunlight, rain or snow.

Don’t use aggressive or abradant detergent for the device surface cleaning.

Use soft wet cloth or tissue to remove strong dirt.

Don’t overpower outlets. It can cause re or electric shock.

Nature protection

Don’t throw away the device with other industrial or nutritive trash if you see that

symbol. Some regions have separation and recycling systems for the electronic

equipment. Connect with local authorities to receive information about recycling of

electronic equipment for your region.

Rights and limitation of liability

languages or reproduced in any way including electronic or mechanical.

Document recording and copying is strictly denied without owner permission.

Table of contents

1. Package ................................................................................................................................................................................... 3

2. Specication.......................................................................................................................................................................... 3

3. Description............................................................................................................................................................................. 4

4. Installation.............................................................................................................................................................................. 5

4.1. Cable requirements............................................................................................................................................. 5

4.2. Schematic diagrams............................................................................................................................................ 6

4.3. Unit mount ............................................................................................................................................................. 8

5. Operation................................................................................................................................................................................ 9

5.1. Incoming call ......................................................................................................................................................... 9

5.2. Outdoor panel and camera monitoring ...................................................................................................... 10

5.3. Incoming call redirection .................................................................................................................................. 11

5.4. Intercom .................................................................................................................................................................. 12

6. Main menu............................................................................................................................................................................. 12

7. Records playback................................................................................................................................................................. 14

8. Settings.................................................................................................................................................................................... 16

8.1. System settings..................................................................................................................................................... 16

8.2. Door settings ......................................................................................................................................................... 17

8.3. Custom MP3 ringtone ........................................................................................................................................ 18

8.4. Camera settings.................................................................................................................................................... 19

8.5. Network settings .................................................................................................................................................. 20

8.6. Service settings..................................................................................................................................................... 21

8.7. Information............................................................................................................................................................. 21

9. Notication modes.............................................................................................................................................................. 22

10. Photo frame......................................................................................................................................................................... 22

11. Standby clock ..................................................................................................................................................................... 23

12. Network connection diagrams..................................................................................................................................... 24

13. Software................................................................................................................................................................................ 25

13.1. Creating new account...................................................................................................................................... 25

13.2. Wired network connection steps................................................................................................................. 25

13.3. Wireless Wi-Fi network connection steps in «AP mode» ..................................................................... 27

13.4. Wireless Wi-Fi network connection steps in «EZ mode»...................................................................... 28

13.5. Operation.............................................................................................................................................................. 29

13.6. Sharing with the other devices..................................................................................................................... 31

13.7. Notication messages...................................................................................................................................... 32

12. Limited Warranty............................................................................................................................................................... 33

Status LED

Touch display

Power switch

Speakers

MicroSD card slot

Microphone

3. Description

133 mm (5.24")

176 mm (6.93") 20 mm (0.78")

1. Package

Sonik 7 Cloud indoor monitor − 1 pc.

Color panel − 1 pc.

Wall mounting bracket − 1 pc.

Connection wires set − 1 pc.

Mounting screws and anchors − 1 pkg.

User manual − 1 pc.

2. Specication

SONIK 7 Cloud

3 4

3 5

SCREEN

7”, color IPS with touch screen

RESOLUTION

1024×600 px.

VIDEO SYSTEM

PAL / NTSC / AHD, TVI, CVI (720p,1080p)

AUDIO TYPE

Half duplex

CALL DURATION

70 seconds

MEMORY

MicroSD card, up to 256 Gb

STANDBY MODE POWER CONSUMPTION

7 W

WORKING MODE POWER CONSUMPTION

11 W

POWER SUPPLY

Built-in power supply, ~100–240 V

MOUNTING TYPE

Surface mount

DIMENSIONS

176×133×20 mm (6.93×5.24×0.78")

WORKING TEMPERATURE

10 ... +55 ˚C (+14...+131 ˚F)

Door 1

Door 2

Camera 1

Camera 2 Output

Ext. power

Network

4.2. Schematic diagrams

Diagram 1. Sonik 7 Cloud outdoor panels, cameras and locks connection.

SONIK 7 Cloud

5 6

Sonik 7 Сloud

GND

+13,5 V

4. Installation

4.1. Cable requirements

Disconnect all power cables before device installation.

able type that is used for device connection depends on the distance between the last indoor monitor in

the system and outdoor panel:

) Use 4-wire cable with such parameters:

• distance up to 25 meters (82 ft.) use a cable with 0,22 mm square of one wire (AWG 24);

• distance 25 to 50 (82-164 ft.) meters use a cable with 0,41 mm square of one wire (AWG 21);

• distance 50 to 100 meters (164-328 ft.) use a cable with 0,75 mm square of one wire (AWG 18).

b) If the distance between door monitor and door panel is between 80 and 100 meters (262-328 ft.) then

use a 3-wire cable with 0,75 mm (AWG 18) square of one wire and RG-59 or RG-6 coaxial cable for the

video signal.

c) Shielded or non-shielded twisted pair (not recommended):

• distance up to 25 meters (82 ft.) non-shielded twisted pair can be used;

Power

Audio

Ground

Video

Power

Audio

Ground

Video

Power

Audio

Ground

Video

Power

Audio

Ground

Video

Power

Audio

Ground

Video

Power

Audio

Ground

Video

0 - 50 m

Shield

50 - 80 m

80 - 100 m

RG-59 or RG-6

0 - 25 m

25 - 50 m

Power

Audio

Ground

Video

Power

Audio

Ground

Video

Power

Audio

Ground

Video

Power

Audio

Ground

Video

Shield Shield

164 - 262 ft.

0 - 164 ft.

262 - 328 ft.

0 - 82 ft.

82 - 164 ft.

Outdoor

panel 1

Outdoor

panel 2

Lock Lock power

supply

Lock Lock power

supply

Power

Audio

GND

Video

Power

Audio

GND

Video

Not used

Alarm

GND

Video

Not used

Alarm

GND

Video

GND

+12 V

Video

GND

+12 V

CCTV 2

CCTV 1

Camera

power

suppply

Camera

power

suppply

Motion

sensor

Motion

sensor

RJ-45 connector

Door 1

Door 2

Camera 1

Camera 2 Output

Ext. powerNetwork

Sonik 7 Сloud (Master)

Door 1

Door 2

CCTV 1

CCTV 2

Input

Output

Ext. power

Door 1

Door 2

CCTV 1

CCTV 2

Input

Output

Ext. power

Diagram 2. Sonik 7 Cloud and Sonik 7 monitors connection into one system.

SONIK 7 Cloud

7 8

Sonik 7 (Slave)

4.3. Unit mount

1) Take the surface mount bracket from the kit and place it on 150-160 cm height.

2) Mark and drill four halls in the wall.

3) Take four anchors from the kit and hammer them into the drilled halls.

4) Fix surface mount bracket on the wall with four screws from the kit.

5) Connect all communication wires and x the monitor on the surface mount bracket.

Notes:

* Use «Power» plug to connect external power supply +13,5 V. While use external power supply please

keep main power cord ~100-240 V disconnected from the outlet, otherwise it can damage monitor

circuits.

** Outdoor panels, cameras, power supplies, locks and motion sensors illustrated on the diagrams are

optional devices and aren’t included into monitor kit.

Audio

GND

Data

Video

Audio

GND

Data

Video

Audio

GND

Data

Video

5.2. Outdoor panels and cameras image view

Monitor displays

image from the

second outdoor panel

(monitoring time – 60 seconds)

Monitor displays

image from the

second CCTV camera

(monitoring time – 60 seconds)

Monitor displays

image from the

rst outdoor panel

(monitoring time – 60 seconds)

5. Operation

5.1. Incoming call

SONIK 7 Cloud

9 10

Press any place

of the screen to

enter main menu

then press

«Monitoring» icon

Press «Camera 1»

icon in the monitor

main menu

Press «Door 1»

icon in the monitor

main menu

Press «Door 2»

icon in the monitor

main menu

Press «Camera 2»

icon in the monitor

main menu

Standby mode

Visitor presses call button

on the rst outdoor panel

Visitor presses call button

on the second outdoor panel

Melody is ringing on the

monitor and outdoor panel,

image from the outdoor panel

appears on the monitor screen

Press «Answer» button to start

conversation with the visitor

Press «Answer» button to start

conversation with the visitor

Melody stops ringing and

conversation starts,

talking time is 120 seconds

Press «Hang up» button to

stop conversation or

incoming call

Press «Hang up» button to

stop conversation or

incoming call

Press «Unlock» button to open

lock connected to the current

outdoor panel. Built-in relay

will open the lock

Standby mode

Notes:

1) Monitor will be automatically switched into standby mode if the user doesn’t answer the incoming call

within 30 seconds.

Monitor displays

image from the

rst CCTV camera

(monitoring time – 60 seconds)

Note:

If somebody presses call button on the outdoor panel while intercom is active then the image from this

outdoor panel appears on the monitors screens and call melody starts ringing. Press «Answer»

button to start conversation with the door panel.

6. Main menu.

In standby mode press any place of the screen to enter main menu. In main menu press any icon to enter

corresponding sub menu. Press button on the upper left corner of the screen to exit from current

sub menu or to exit into standby mode.

All settings are saved automatically after changing its value.

5.4. Intercom

Two monitors connected into one system are used.

Melody starts ringing

on the other monitor

5.3. Incoming call redirection

Two monitors connected into one system are used.

Press «Answer» button on the

other monitor to start

conversation with the visitor

SONIK 7 Cloud

11 12

Press any place of the

screen to enter

main menu

Press «Intercom»

icon in the

main menu

Notes:

1) If several monitors are connected into one system, the user can view the image from outdoor panels

and cameras on any monitor inside this system. The image will be transferred from the «Master» monitor

outdoor panels and cameras to the «Slave» monitors.

2) If somebody presses call button on the outdoor panel while monitoring is active then the image from

this outdoor panel appears on the monitor screen and call melody starts ringing. Press «Answer»

button to start conversation.

Note:

If incoming call is successfully redirected to the other monitor and other user answers the call then current

monitor enters standby mode.

Incoming call from the

outdoor panel starts and

user begins conversation

Press «Redirect»

button to start

call redirection

Melody starts ringing on

the other monitor inside

the system and visitor image

appears on the monitor screen

Conversation with

the other

monitor begins

Press «Unlock» button to open

lock connected to the current

outdoor panel, built-in relay

will open the lock

Press «Hang up» button to

stop conversation or

incoming call

Standby mode

Press «Answer» button

on the other monitor

to start conversation

Conversation with the

other monitor starts

Press «Hang up» button

to stop current

conversation

Standby mode

13 14

SONIK 7 Cloud

7. Records playback

Press «Records» icon in the main menu to enter records playback menu:

Following folders are available in the «Records» menu:

Call records − incoming call video records viewing;

Message records − voice records from outdoor panel if nobody is at home;

Motion records − software motion detection video records;

Alarm records − hardware motion detection video records using external sensors .

Door 1

Current video channel

Answer

Hang up

Unlock

Image and volume

settings bar

Decrease current

parameter value Increase current

parameter value

Call

redirection

Enable/

disable image

and volume

settings bar

Start/stop

video recording

Video input

switch

Image monitoring screen has following elements:

Records

Settings

Intercom

Photo frame

Monitoring

At home

06-10-2021 12 : 01

Motion records

Message records

Call records

Alarm records

Camera1

Door2

Door1

Camera2

06-10-2021 12 : 01

REC

− +

Main menu

Monitoring

REC

Main menu

Outdoor panels and cameras monitoring is available directly from the main menu of the monitor by

touching corresponding icons:

Door1 − door 1 image monitoring;

Door1 − door 2 image monitoring;

Camera1 − camera 1 image monitoring;

Camera1 − camera 2 image monitoring.

Main menu

Take a

snapshot

SONIK 7 Cloud

15 16

Main menu

Records

Call records

Message records

Motion records

Alarm records

Next pagePrevious page

Current record

playback

2019/09/18 15:40:42

Press icon on the right side of the file name to start current file playback. Also you can stop playback,

delete current le, set up volume or get back to the list of video les using the buttons on the bottom of

the screen:

− start/stop playback;

− previous/next le playback;

− delete current le;

− decrease/increase playback volume;

− get back to the les list.

Call records (11-1/2)

20210105061950_0010_DOOR2.mov Read

20210105061842_0002_DOOR1.mov Not read

20210105061840_0000_DOOR1.mov Not read

20210105061727_0001_DOOR1.mov Not read

20210105061725_0001_DOOR1.jpg Read

20210105061724_0001_DOOR1.mov Not read

20210105061549_0001_DOOR1.jpg Not read

20210105061548_0001_DOOR1.jpg Not read

20210105061546_0001_DOOR2.jpg Read

20210105061544_0001_DOOR2.jpg Read

− +

20210105061950_0010_DOOR2.mov

00:00 00:03 7

DOOR2 05/01/2021 06:19:50

−+

8. Settings

8.1. System settings

Press «Settings» icon in the main menu then press «System» icon to enter system settings menu:

Following folders are available in the «Settings» menu::

System − monitor system settings, language setting, time setting, etc.;

Door − outdoor panels video standard setting, melody and motion detection settings;

Camera − cameras video standard and motion detection settings;

Network − device network settings;

Service − microSD card format, factory default settings and software update;

Information − program software version and UUID identication number.

Main menu

Settings

Camera

Network

Door

Information

System

Service

Main menu

Settings

System

Device id 1

Time 08-11-2021 14:55

Date format DD-MM-YY

Standby clock 60 Sec

Language English

Keytone

Door panel backlight

SONIK 7 Cloud

17 18

Main menu

Settings

Door

Main menu → Settings → System

Device ID − this monitor model can only be «Master» in the system;

Time − current date and time settings;

Date format − date format setting;

Standby clock − clock display in standby mode time, from 10 to 180 sec. or Off;

Language − menu language setting;

Keytone − enable/disable screen touching sound;

Door panel backlight − enable/disable call button backlight on the outdoor panel.

8.2. Door settings

Press «Settings» icon in the main menu then press «Door» icon to enter outdoor panels settings menu:

Main menu → Settings → Door

Channel activation − include or exclude current video channel from viewing list;

Signal mode − PAL, NTSC or Automatic;

Signal type − AHD 720P / AHD 1080P / TVI 720P / TVI 1080P /CVI 720P / CVI 1080P / CVBS;

Unlock time − relay unlocking time, from 1 to 10 sec.;

Record mode − record type when incoming call or motion event occurs, «Snapshot» or «Video»;

Motion detection − enable and set the sensitivity of program motion detection;

Motion detection duration − program motion detection recording time;

Motion display − enable/disable screen activation if program motion detection occurs;

Motion ringtone − enable and set the melody if program motion detection occurs;;

Message − delay time before message recording if nobody answers incoming call;

Ring setting − outdoor panels melody settings;

Door 1

Channel activation

Signal mode PAL

Signal type AHD1080

Unlock time 2 Sec

Record mode Video

Motion detection Medium

Motion detection duration 10 Sec

Motion display

Motion ringtone 3

Message 30 Sec

Ring setting

Door 1

Door 2

Main menu

Settings

Door

Ring setting

Door 1 / Ring 1

Schedule 06 : 00 - 12 : 00

Time 10 Sec

Ring mode Standard

Ring select 4

Ring volume 5

Outdoor panel volume O

Ring 1

Ring 2

Ring 3

Main menu → Settings → Door → Ring setting

Schedule − time of the day to apply following settings;

Time − incoming call melody ringing time from 5 to 45 sec.;

Ring mode − «Standard» - default melodies from internal memory or «Customize» - choose mp3

melody from the «Ring» folder on microSD card;

Ring select − choose the melody for the current outdoor panel;

Ring volume − set incoming call melody volume level on the monitor, from 0 to 10;

Outdoor panel volume − set call melody volume level on the outdoor panel, from 1 to 10 or O.

8.3. Custom MP3 ringtone

Create «USER» folder in the root of microSD card then create «Ring» folder inside of the «USER» folder if it

wasn’t already created by the monitor. Paste MP3 files you would like to use as a ringtone inside of the

«Ring» folder. File names must have only English letters and figures in its names and its quantity must not

exceed 8 symbols to be visible on the monitor.

Insert microSD card into the monitor and go to the «Settings» → «Door» → «Ring setting» menu. Then

choose «Ring mode» → «Custom» and choose the melody to use as a ringtone in the «Ring select» menu.

Pay attention that melody is active only for the time period specified in the «Schedule» menu. There are 3

time periods for every outdoor panel specified as «Ring 1», «Ring 2» and «Ring 3» bookmarks on the left

bar. Every time period has its own melody, volume and ringing time.

SONIK 7 Cloud

19 20

Network

Net pairing mode AP mode

Cloud services Unconnected

Wi-Fi hotspot SmartLife-b1e24f

Password 12345678

Main menu → Settings → Camera

Channel activation − include or exclude current video channel from viewing list;

Sensor type − type of the sensor connected to the corresponding camera:

«NO», motion sensor with normally disconnected (opened) contacts is used;

«NC», motion sensor with normally connected contacts is used;

«O», motion sensor is not used;

Signal mode − PAL, NTSC or Automatic;

Signal type − AHD 720P / AHD 1080P / TVI 720P / TVI 1080P /CVI 720P / CVI 1080P / CVBS;

Alarm time − alarm time in case of hardware motion detection event, from 1 to 20 sec.;

Alarm record mode − record type when motion event occurs, «Snapshot» or «Video»;

Motion detection − enable and set the sensitivity of program motion detection;

Motion detection duration − program motion detection recording time;

Motion display − enable/disable screen activation if program motion detection occurs;

Motion ringtone − enable and set the melody if program motion detection occurs.

Hardware motion detection can detect motion by means of external device (hardware motion sensor).

There are two types of sensors that can be connected to the monitor: sensor with normally opened

contacts (NO) and sensor with normally closed contacts (NC).

Depending on the type of sensors that are used appropriate settings must be made in the hardware

motion detection settings menu. External sensors connection diagram you can nd on the page 6.

Main menu → Settings → Network

Net pairing mode − monitor network connection mode,

«AP mode» – manual Wi-Fi connection mode;

«Cable» – wiring conection to the local network;

«EZ mode» – automatic Wi-Fi connection mode;

Cloud services − cloud server connection status;

Wi-Fi hotspot − hotspot name;

Password − hotspot password;

IP address − device network IP address (available only in «Cable» and «EZ mode»);

MAC − device MAC address (available only in «Cable» and «EZ mode»).

Main menu

Settings

Camera

8.4. Camera settings

Press «Settings» icon in the main menu then press «Camera» icon to enter camera settings menu:

Camera 1

Channel activation

Sensor type NO

Signal mode PAL

Signal type AHD1080

Alarm time 4 Sec

Alarm record mode Video

Motion detection O

Motion detection duration 20 Sec

Motion display

Motion ringtone O

Camera 1

Camera 2

Main menu

Settings

Network

8.5. Network settings

Press «Settings» icon in the main menu then press «Network» icon to enter network settings menu:

SONIK 7 Cloud

21 22

8.7. Information

Press «Settings» icon in the main menu then press «Information» icon to enter information menu.

Main menu → Settings → Information

Software version − current software version of the monitor;

Release date − software release date;

SD remain space − microSD card installed into monitor slot information;

UUID − unique cloud identification number.

Main menu → Settings → Service

Formatting SD disk − microSD card format;

Factory settings − restore factory default settings of the monitor;

Software update − software update of the monitor. Place update file «update.ius» in microSD root

folder, then choose this menu to start update process;

Restart system − monitor reboot.

Service

Formatting SD disk Ok

Factory settings Ok

Software update Ok

Restart system Ok

Information

Software version 3.0.0.1

Release date 2021-10-21

SD remain space 7.1G/7.2G

UUID *04be4d97

9. Notication modes

Monitor has 3 modes. Depending on the current active mode, sound notications type changes. User can

change current mode by touching corresponding icon in the main menu:

Sound notifications are enabled, both on the monitor and on the outdoor panel;

Sound notifications are disabled on the monitor, but enabled on the outdoor panel;

Visitor can leave voice messages for the user in this mode if corresponding «Message»

function is enabled in the «Settings» → «Door» menu;

Sound notifications are disabled, both on the monitor and on the outdoor panel.

Dormant

At home

Not at home

8.6. Service settings

Press «Settings» icon in the main menu then press «Service» icon to enter service settings menu:

Main menu

Settings

Service

Main menu

Settings

Service

10. Photo frame

Create «USER» folder in the root of microSD card then create «Digital Frame» folder inside of the «USER»

folder if it wasn’t already created by the monitor. Paste JPG images you would like to view inside of the

«Digital Frame» folder. File name must have only English letters and figures in its name and its length must

not exceed 30 symbols to be visible on the monitor .

Note that JPG images resolution must not exceed 1024×600 pixels. Other image formats and resolutions

are not supprted.

SONIK 7 Cloud

23 24

Insert microSD card into the monitor slot and press «Photo frame» icon in the main menu to enter photo

frame settings:

Photo frame

Main menu

Photo frame

Switching ime 3 Sec

Background music

Background volume 5

Main menu → Photo frame

Photo frame − enable/disable photo frame function in standby mode;

Switching time − photo switching interval, from 3 to 30 sec.;

Background music − enable/disable background music playback in photo frame mode;

Background volume − set background music volume in photo frame mode.

11. Standby clock

If «Standby clock» function is enabled in «Settings» → «System» menu then user can see the folowing

screen after exiting from the main menu or conversation ending:

11 : 28

26-10-2021 Tuesday

0 22 1

Call records

Message records

Motion records

Alarm records

WAN 1 2 3 4

Android / iOS

Sonik 7 Cloud

Android / iOS

Smart call

Internet

3G / Wi-Fi

Router

12. Network connection diagrams

Diagram 1. Sonik 7 Cloud wired network connection.

Diagram 2. Sonik 7 Cloud wireless Wi-Fi network connection.

Android / iOS

Internet

3G / Wi-Fi

Wi-Fi (LAN)

«AP or EZ mode»

Router

SONIK 7 Cloud

25 26

13. Software

Enter «Google Play» (for Android) or «Apple App Store» (for iOS) and search for «Smart Call» application,

then install this applicationи on your mobile device.

13.1. Creating new account

1) Start «Smart Call» application on your mobile device and press «SIgn up» button to create an account;

2) Choose destination country and enter your Email, then press «Get verication code» button to receive

an Email with verification code;

3) Check the Email, specied on the previous step;

4) Enter 6-digit code from the letter to activate your account. Set your password and press «Finish» to

nalize account creation process. Use your Email as a login for

13.2. Wired network connection steps

1) Use twisted pair CAT5 or CAT6 cable to connect device to the router;

2) Connect mobile device into the same local network;

3) Press «Add device» button and choose device model for connection. Then choose «Cable» connection

type in the upper right corner;

4) Turn on the monitor power and press «Next» button in the application;

5) In the monitor main menu press «Settings» → «Network» → «Net pairing mode» set «Cable» type of

connection. Monitor will reboot after exiting «Network» menu. After monitor reboot press «Next»

button in the «Smart Call» application;

6) Enable «Next step» switch then press «Next» button. Network devices search will be started;

7) Choose Sonik7 Cloud device in the list and it will be paired to the current account of the «Smart Call»

application.

SONIK 7 Cloud

27 28

13.3. Wireless Wi-Fi network connection steps in «AP mode»

1) Connect mobile device into the same Wi-Fi network you want to connect the monitor;

2) Disable 3G/4G internet connection on your mobile device;

3) Press «Add device» button and choose device model for connection;

4) Turn on the monitor power and press «Next» button in the application;

5) In the monitor main menu press «Settings» → «Network» → «Net pairing mode» set «AP mode» type of

connection. Monitor will reboot after exiting «Network» menu. After monitor reboot press «Next»

button in the «Smart Call» application;

6) Enable «Next step» switch then press «Next» button;

7) Enter Wi-Fi network name, the monitor will be conected to, and network password. Then press «Next»

button to go to the next step;

8) Press «Go to connect» button and manually conect mobile phone to the Wi-Fi hotspot of the monitor.

Wi-Fi hotspot name is «SmartLife-xxxxxx». Password: 12345678;

9) When mobile phone is connected to the Wi-Fi hotspot, come back to the mobile application. The

monitor will be connected to the Wi-Fi network, specied on the 7-th step and paired to the current

account of the «Smart Call» application.

If current device is already paired to some account in

the «Smart Call» application

, then it

is impossible to add this device to any other account. To add this device to some other

account delete this device in the account, it is currently connected to!

13.4. Wireless Wi-Fi network connection steps in EZ mode

1) Connect mobile device into the same Wi-Fi network you want to connect the monitor;

2) Disable 3G/4G internet connection on your mobile device;

3) Press «Add device» button and choose device model for connection. Then choose «EZ mode»

connection type in the upper right corner of the screen;

4) Turn on the monitor power and press «Next» button in the application;

5) In the monitor main menu press «Settings» → «Network» → «Net pairing mode» set «EZ mode» type of

connection. Monitor will reboot after exiting «Network» menu. After monitor reboot press «Next»

SONIK 7 Cloud

29 30

button in the application;

6) Enable «Next step» switch then press «Next» button;

7) Enter Wi-Fi network name, the monitor will be conected to, and network password. Then press «Next»

button to go to the next step;

8) The monitor will be connected to the Wi-Fi network, specied on the 7-th step and paired to the

current account of the «Smart Call» application.

13.5. Operation

Press device icon

to start monitoring

Go to the

main menu

Enable conversation

mode

Outdoor panel 1

Outdoor panel 2

Camera 1

Camera 2

Take a snapshot

Record video

Video channels

switching

Records playback

from the

monitor archive

Mobile phone records

local archive playback

Open lock

(Default password:

888888)

Advanced settings

Enable sound

from the

outdoor panel

Main

settings

Full screen

mode

Main menu Monitoring menu

SONIK 7 Cloud

31 32

13.6. Sharing with the other devices

The account, device is added for the first time, is master account. This account has master permissions and

can change all the settings. If several mobile phones are going to be used with the same device then

personal account must be created on every mobile phone. Here are the steps to add the same device on

several mobile phones:

1) Create an account on the rst mobile phone application and add your device. Account on this mobile

phone will be the master account for this device;

2) Install «Smart Call» application on every mobile phone that is going to be used and create its own

account in every application. Every mobile phone must use it’s own account in the application;

3) Using master account enter device monitoring screen, press icon on the right upper corner of

the screen and enter «Add sharing» menu. Enter account name, used on the shared device and press

«Done» button on the right upper corner of the screen. Shared account must be added to the sharing

list. It means that the user on the shared mobile phone now have an access to this device;

4) In the same manner add all other mobile devices into sharing list.

Press «Accept» button to start

conversation with the visitor or

«Decline» to hang up incoming

call.

13.7. Notication messages

Press «Me» bookmark on the bottom of the main screen, then press icon on the right upper corner of

the screen and enter «App Notication» menu. Here you can enable or disable notification messages from

the application.

SONIK 7 Cloud

33 34

14. Limited warranty

Manufacturer guarantees product normal functioning during the warranty period if the user keeps all

safety instructions described in that manual.

Warranty period is 12 months from the moment of the product purchasing (warranty period could be

extended up to 24 months or more, depending on the local regulations).

Warranty period allows user to make guarantee repair in cases when normal functioning of the product

was violated by the fault of manufacturer and the user has not oend transporting, installation and

working conditions.

This limited warranty does not cover any damage to the product that results from improper installation,

accident, abuse, misuse, natural disaster, insucient or excessive electrical supply, abnormal mechanical

or environmental conditions, or any unauthorized disassembly, repair or modication.

Warranty void in such cases:

• the product was damaged by the fault of the customer;

• the product wasn’t properly installed according reccomendations from the manual;

• the sticker on the backside of the product was broken;

• the product was not used for its intended function.

This limited warranty covers only repair, replacement, refund or credit for defective products, as provided

above. Manufacturer is not liable for, and does not cover under warranty, any damages or losses of any

kind whatsoever resulting from loss of, damage to, or corruption of, content or data or any costs

associated with determining the source of system problems or removing, servicing or installing products.

This warranty excludes third party software, connected equipment or stored data. Manufacturer is

therefore not liable for any losses or damage attributable to third party software, connected equipment or

stored data.

In the event a product has been discontinued, manufacturer shall either repair the product, oer to

replace it with a comparable product or provide a refund at the lesser of the purchase price or the

product’s current value.

Repaired or replacement products will continue to be covered by this limited warranty for the remainder

of the original warranty term.

Содержание

1. Комплект поставки............................................................................................................................................................ 37

2. Характеристики.................................................................................................................................................................. 37

3. Описание ............................................................................................................................................................................... 38

4. Установка............................................................................................................................................................................... 39

4.1 Выбор кабеля ........................................................................................................................................................ 39

4.2 Схемы подключения.......................................................................................................................................... 40

4.3 Монтаж..................................................................................................................................................................... 42

5. Эксплуатация ....................................................................................................................................................................... 43

5.1. Вызов с вызывной панели.............................................................................................................................. 43

5.2. Просмотр панелей и камер........................................................................................................................... 44

5.3. Переадресация вызова ................................................................................................................................... 45

5.4. Внутренняя связь ............................................................................................................................................... 46

6. Главное меню....................................................................................................................................................................... 46

7. Просмотр записей............................................................................................................................................................. 48

8. Настройки ............................................................................................................................................................................. 50

8.1. Системные настройки...................................................................................................................................... 50

8.2. Настройки вызывных панелей..................................................................................................................... 51

8.3. Установка пользовательских MP3 мелодий........................................................................................... 52

8.4. Настройки дополнительных камер ........................................................................................................... 53

8.5. Cетевые настройки............................................................................................................................................ 54

8.6. Cервисные настройки...................................................................................................................................... 55

8.7. Информация о системе ................................................................................................................................... 55

9. Режим работы...................................................................................................................................................................... 56

10. Фоторамка.......................................................................................................................................................................... 56

11. Часы в режиме ожидания............................................................................................................................................ 57

12. Схемы подключения домофона к локальной сети .......................................................................................... 58

13. Программное обеспечение........................................................................................................................................ 59

13.1. Создание учетной записи............................................................................................................................ 59

13.2. Подключение к проводной сети............................................................................................................... 59

13.3. Подключение к беспроводной Wi-Fi сети в режиме AP................................................................. 61

13.4. Подключение к беспроводной Wi-Fi сети в режиме EZ.................................................................. 62

13.5. Управление........................................................................................................................................................ 63

13.6. Общий доступ к устройству........................................................................................................................ 65

13.7. Оповещения о входящих вызовах........................................................................................................... 66

14. Условия гарантии............................................................................................................................................................ 67

Указания по безопасности

Прочтите и сохраните эту инструкцию.

Все работы, связанные с установкой данного продукта, должен выполнять квалифицированный

специалист.

Соблюдайте температурный режим, используйте прибор при температуре от -10 ˚C до +55 ˚C.

Устанавливать устройство следует на поверхностях, не склонных к вибрациям или ударным

нагрузкам.

Устанавливайте устройство вдали от открытых источников тепла, таких как радиаторы,

обогреватели и печи.

Допускается установка устройства вблизи других устройств бытовой электроники, если

температура окружающей среды не выходит за границы вышеупомянутых температур.

Устройство должно быть защищено от погодных воздействий, таких как прямой солнечный свет,

вода (дождь) или снег.

Не используйте агрессивные или абразивные моющие средства для чистки корпуса прибора.

Используйте мягкую увлажненную ткань или салфетку для удаления трудных загрязнений.

Защита окружающей среды

Если вы видите этот символ на продукте, не выбрасывайте его с промышленными

или пищевыми отходами. В некоторых регионах созданы системы для сбора и

утилизации электронного оборудования. Свяжитесь с местными органами власти

для получения информации об утилизации для вашего региона.

Авторские права и ограничение ответственности

форме и любыми средствами, переведена на другой язык, переписана, переделана в любой другой

форме, храниться в поисковой системе или передаваться любыми средствами, включая

электронные или механические.

Запрещена запись или ксерокопирование без предварительного письменного разрешения

владельца.

Внимание!

В связи с постоянным проведением модернизаций и улучшения функциональности

оборудования, внешний вид, технические характеристики и функциональность

могут быть изменены без предварительного уведомления.

Данное руководство пользователя может содержать неточности или опечатки.

Производитель оставляет за собой право вносить изменения к информации,

содержащейся в данном руководстве, а также к комплектации и/или общему

описанию изделия.

SONIK 7 Cloud

35 REV. 1.0 36

ЭКРАН

7”, сенсорный цветной IPS

РАЗРЕШЕНИЕ

1024×600 пикселей

ВИДЕОСИСТЕМА

PAL/NTSC/AHD, TVI, CVI (720p,1080p)

ТИП АУДИОСВЯЗИ

Полудуплексная

ДЛИТЕЛЬНОСТЬ ВЫЗОВА

70 секунд

СЛОТ КАРТЫ ПАМЯТИ

MicroSD, до 256 ГБ

ПОТРЕБЛЕНИЕ В РЕЖИМЕ ОЖИДАНИЯ

7 Вт

ПОТРЕБЛЕНИЕ В РЕЖИМЕ РАБОТЫ

11 Вт

БЛОК ПИТАНИЯ

Встроенный источник питания, ~100-240 В

ТИП УСТАНОВКИ

Накладной монтаж

РАЗМЕРЫ

176×133×20 мм

РАБОЧАЯ ТЕМПЕРАТУРА

–10 ... +55 ˚C

Индикатор состояния домофона

Дисплей

Выключатель питания

Динамики

Слот для microSD карты памяти

Микрофон

3. Описание

133 мм

176 мм 20

мм

1. Комплект поставки

Домофон Sonik 7 Cloud − 1 шт.

Cменная цветная панель − 1 шт.

Кронштейн для крепления на стену − 1 шт.

Провода для подключения − 7 шт.

Комплект саморезов и дюбелей для монтажа − 1 компл.

Инструкция по эксплуатации − 1 шт.

2. Характеристики

SONIK 7 Cloud

37 38

3 5

Страница загружается ...

Slinex Sonik-7 Cloud Руководство пользователя

Бренд: Slinex

Модель: Sonik-7 Cloud

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

на других языках

English: Slinex Sonik-7 Cloud User manual

Slinex Sonik-7 Cloud Руководство пользователя

Slinex Sonik-7 Cloud Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов