Tripp Lite Switched/Metered Rack PDU Инструкция по применению

PROTECT YOUR INVESTMENT!

Register your product for quicker service

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Owner’s Manual

Switched/Metered Rack PDU

with Automatic Transfer Switch

Models: PDUMH15AT, PDUMH15ATNET, PDUMH15HVAT,

PDUMH15HVATNET, PDUMH20AT, PDUMH20ATNET,

PDUMH20HVAT, PDUMH20HVATNET

Series Number: AGAC7625

1. Important Safety Instructions 2

2. Installation 3

2.1 Mounting the PDU 3

2.2 Connecting the PDU 3

2.3 Networking the PDU 6

3. Features 7

4. Conﬁguration and Operation 10

4.1 Automatic Transfer Switch 10

5. Technical Support 12

6. Warranty and Product Registration 12

Español 13

Français 25

Русский 37

18-09-500-933721.indb 1 10/4/2018 3:59:55 PM

2

SAVE THESE INSTRUCTIONS

• This manual contains instructions and warnings that should be followed

during the installation, operation, and storage of this product. Failure to

heed these instructions and warnings may affect the product warranty.

• Warning: This equipment is compliant with Class A of CISPR 32. In a

residential environment, this equipment may cause radio interference.

• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge or line noise

protection for connected equipment.

• The PDU is designed for indoor use only, in a controlled environment, away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• Keep indoor ambient temperature between 32°F and 122°F (0°C and 50°C).

• The PDU must be installed by a qualified technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Code standards. Be sure to use the proper

overcurrent protection for the installation, in accordance with the plug/equipment rating.

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• The electrical outlets supplying power to the equipment should be installed near the equipment

and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the PDU should not draw more current than the individual

PDU’s outlet’s rating.

• The total load connected to the PDU must not exceed the maximum load rating for the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to significantly affect its safety

or effectiveness is not recommended.

1. Important Safety Instructions

18-09-500-933721.indb 2 10/4/2018 3:59:55 PM

PDUMH15AT, PDUMH15ATNET,

PDUMH20AT, PDUMH20ATNET

PDUMH15HVAT, PDUMH15HVATNET

PDUMH20HVAT, PDUMH20HVATNET

PDUMH15HVATNET

3

Primary InputSecondary Input

9

Primary Input

Secondary Input

Unswitched

Outlets

2.2.1

PDUMH20AT

PDUMH20ATNET

PDUMH15AT

PDUMH15ATNET

PDUMH20HVAT

PDUMH20HVATNET

Primary Input (120V Models) Primary Input (208-240V Models)

2.1 Mounting the PDU

The PDU supports 1U Rack configurations.

Note: The user must determine the fitness of

hardware and procedures before mounting. The PDU

and included hardware are designed for common

rack and rack enclosure types and may not be

appropriate for all applications. Exact mounting

configurations may vary.

1U Rack Mounting: Attach the PDU to the

rack by inserting four user-supplied screws

A

through the PDU mounting brackets

B

and

into the mounting holes of the rack rail as

shown.

2. Installation

B

A

2.2 Connecting the PDU

All PDU models include a primary and secondary AC power input (see diagram). The reference

table below lists each model’s primary and secondary inputs:

Model Primary Input Secondary Input*

PDUMH15AT NEMA 5-15P (permanent cord) IEC C14 inlet

PDUMH15ATNET NEMA 5-15P (permanent cord) IEC C14 inlet

PDUMH15HVAT IEC C14 inlet (detachable cord) IEC C14 inlet

PDUMH15HVATNET IEC C14 inlet (detachable cord) IEC C14 inlet

PDUMH20AT NEMA 5-15P (permanent cord) IEC C20 inlet

PDUMH20ATNET NEMA 5-15P (permanent cord) IEC C20 inlet

PDUMH20HVAT IEC C20 inlet (detachable cord) IEC C20 inlet

PDUMH20HVATNET IEC C20 inlet (detachable cord) IEC C20 inlet

Note: The PDUMH15HVATNET model uses plug lock inserts over C13 plugs to securely connect to the C14

primary and secondary inputs.

18-09-500-933721.indb 3 10/4/2018 3:59:57 PM

4

2.2.2 To connect the Secondary

input cord:

Form a loop in the Secondary cord

A

and

secure the juncture of that loop to the Primary

cord

B

with a zip tie. Be sure the zip tie is

secured around the Secondary and Primary

cords, as well as through the loop created in

the Secondary cord

C

. (See diagram).

Note: Allow the cord as much slack as possible

between the loop and the cord’s outlet.

On Models PDUMH20HVAT and

PDUMH20HVATNET, both cords should be tied

to the Cable Retention Tray. (See diagram).

Once two cords are secured and the

Secondary cord has an acceptable amount of

slack, insert the Secondary cord outlet into the

IEC power inlet.

Note: The PDUMH15HVATNET model uses plug lock

inserts over C13 plugs to securely connect to the

C14 primary and secondary inputs.

2.2.3 Connect Input Plug

Adapters (Optional - Models

PDUMH20AT, PDUMH20ATNET

Only):

The PDU includes two adapters that convert

one or both of the L5-20P input plugs to

5-20P input plugs. Connecting the adapters is

optional. The PDU will function normally

without connecting the adapters.

2.2.4 Connect Secondary Input

Cord to PDU:

Although the PDU will operate without

connecting the Secondary input cord, the

Secondary input is required for the PDU's

Automatic Transfer Switch function.

2. Installation

Primary InputSecondary Input

9

2.2.2

2.2.3

2.2.4

PDUMH20AT,

PDUMH20ATNET

PDUMH20AT,

PDUMH20ATNET

PDUMH15HVAT, PDUMH15HVATNET

PDUMH15AT,

PDUMH15ATNET

A

B

C

18-09-500-933721.indb 4 10/4/2018 3:59:58 PM

Primary Input

Secondary Input

Unswitched

Outlets

PDUMH20AT,

PDUMH20ATNET

PDUMH20HVAT,

PDUMH20HVATNET

PDUMH15HVAT,

PDUMH15HVATNET

PDUMH15AT,

PDUMH15ATNET

2.2.6

A

5

2. Installation

2.2.5 C13-C14 (Models:

PDUMH15HVAT and

PDUMH15HVATNET) or C19-C20

Cables (Models PDUMH20HVAT

and PDUMH20HVATNET only):

The PDU includes one C13 to C14

(PDUMH15HVAT/NET) or two C19 to C20

(PDUMH20HVAT/NET) interconnection cables

for the two primary and secondary inlets,

which may be used to connect to upstream

UPS sources. Alternately, the user can supply

IEC cables fitted with country-specific plugs.

Primary Input

Secondary Input

Unswitched

Outlets

Primary InputSecondary Input

9

2.2.5

PDUMH20HVAT, PDUMH20HVATNET

PDUMH15HVAT, PDUMH15HVATNET

2.2.6 Connect PDU Input Plugs:

(See the Configuration and Operation section for more information.) Connect the Primary input

plug

A

to a preferred source of grounded 120V/230V AC power, such as a SmartOnline

®

UPS

System. The UPS system must not share a circuit with a heavy electrical load (such as an air

conditioner or refrigerator). Under normal operating conditions, the PDU will distribute AC power

from the Primary input source. Connect the Secondary input plug

B

to an alternative source of

grounded 120V/230V AC power, such as a redundant SmartOnline UPS System. Do not plug the

Secondary input into the same power source as the Primary input. The PDU will distribute AC power

from the Secondary input only if the Primary input becomes unavailable.

Note: Immediately after the PDU is connected to live AC power, you may notice a series of soft clicking sounds

emitted by electrical relays within the PDU. The relays may also click occasionally during the operation of the

PDU. This is normal.

B

A

18-09-500-933721.indb 5 10/4/2018 4:00:00 PM

RESET

STATUS

CONFIG

Primary Input

Secondary Input

Unswitched

Outlets

Primary InputSecondary Input

9

RESET

STATUS

CONFIG

2.2.8

PDUMH20ATNET

PDUMH20AT

PDUMH20HVAT, PDUMH20HVATNET

PDUMH15HVAT, PDUMH15HVATNET

PDUMH15ATNET

PDUMH15AT

6

2. Installation

2.2.7 Selecting Input Voltage Range (optional: Models PDUMH15HVAT,

PDUMH15HVATNET, PDUMH20HVAT and PDUMNH20HVATNET only):

These models have two selectable nominal input voltage ranges: 200V-208V (“LO”) and

220V-240V (“HI”). Press the button next to the display to toggle the nominal voltage setting to the

desired “HI” or “LO” range. This setting adjusts the voltage ranges for the primary and secondary

inputs. The display will indicate “HI” or “LO” for five seconds.

2.2.8 Connect Equipment to PDU:

Do not exceed the load rating of the PDU. The total electrical current used by the PDU will be

displayed on the digital meter in amperes. Each outlet includes a green LED that illuminates when

the outlet is receiving AC power.

2.3 Networking the PDU

For network configuration instructions, please refer to the WEBCARDLX Owner’s Manual

included with this product.

18-09-500-933721.indb 6 10/4/2018 4:00:01 PM

3

5

3 4 2 1

6

6 8

1 2 3

6

*NET models only.

7

PDUMH20AT, PDUMH20ATNET

PDUMH15AT, PDUMH15ATNET

PDUMH15HVAT, PDUMH15HVATNET

PDUMH20HVAT, PDUMH20HVATNET

3. Features

3

5

1 2

6

7

2

6

14

18-09-500-933721.indb 7 10/4/2018 4:00:03 PM

8

3. Features

1

Primary Input

Models PDUMH15AT/NET: The cord is permanently attached to the PDU and has a NEMA

5-15P plug.

Models PDUMH15HVAT/NET: The C13-C14 cord is detachable.

Models PDUMH20AT/NET: The cord is permanently attached to the PDU and has a

NEMA L5-20P plug.

Models PDUMH20HVAT/NET: The C19-C20 cord is detachable.

2

Secondary Input Inlet (detachable on all models)

Models PDUMH15AT/NET, PDUMH15HVATNET: The IEC-320-C14 inlet connects to the

detachable Secondary AC Input Power Cord.

Models PDUMH20AT/NET, PDUMH20HVAT/NET: The IEC-320-C20 inlet connects to the

detachable Secondary AC Input Power Cord.

3

Switched Outlets: During normal operation, the outlets distribute AC power to connected

equipment. On Models PDUMH15ATNET, PDUMH15HVATNET, PDUMH20ATNET and

PDUMH20HVATNET, the NEMA 5-15R, NEMA 5-15/20R and IEC-320-C13 outlets may be

switched On and Off via software control. When an outlet is live, the associated LED

illuminates.

4

Unswitched Outlets (Models PDUMH15HVAT/NET, PDUMH20HVAT/NET): These outlets

receive power from either input source, but are not individually switchable.

5

Factory Configuration Port: The port is reserved for configuration by factory authorized

personnel only. No user information is available. Connecting to this port may render the unit

inoperable and void its warranty.

6

Digital Load Meter (Ammeter): The total electrical current used by the connected equipment

is displayed on the digital meter in amperes.

Input Voltage Range Select Switch (Models PDUMH15HVATNET, PDUMH20HVATNET): The

button to the lower left of the display may be used to toggle between “HI” or “LO” voltage

ranges. The display will indicate “HI” or “LO” for five seconds. Press the switch once to display

ranges, press again within five seconds to change setting. Setting can also be changed via

PowerAlert (PDUMH15HVATNET and PDUMH20HVATNET only).

IP Address Display (Models PDUMH15HVATNET, PDUMH20HVAT/NET): Press and hold the

switch to display the IP address of the SNMP card in the PDU.

7

Network Interface (Models PDUMH15ATNET, PDUMH15HVATNET, PDUMH20ATNET,

PDUMH20HVATNET): Allows you to operate the PDU as a managed network device, accessible

via SNMP network management platform, web browser, SSH or Telnet.

8

Input Source Indicator: When the PDU is connected to a live AC power source, the Primary or

Secondary input LED illuminates to indicate which source is supplying power to the outlets.

18-09-500-933721.indb 8 10/4/2018 4:00:03 PM

9

Primary and Secondary AC Input Power Cord

(Models PDUMH20HVAT, PDUMH20HVATNET): Two C19-C20

cables are included: one for Primary Input, and one for Secondary

Input.

Primary AC Input Power Cord

(Models PDUMH15HVAT, PDUMH15HVATNET): A C13-C14 cable

is included.

Secondary AC Input Power Cord

(Models PDUMH15AT, PDUMH15ATNET): The detachable cord

has an IEC-320-C13 connector and a NEMA 5-15P plug.

Secondary AC Input Power Cord

(Models PDUMH20AT, PDUMH20ATNET): The detachable cord

has an IEC-320-C19 connector and a NEMA L5-20P plug.

Input Plug Adapters

(Models PDUMH20AT, PDUMH20ATNET): The adapters convert

NEMA L5-20P input plugs to NEMA 5-20P input plugs.

Plug Lock Inserts

(Models PDUMH15HVAT, PDUMH15HVATNET): Prevent

accidental disconnection of C13-C14 or C19-C20 power cords.

Cable Retention Tray

(Models PDUMH20HVAT, PDUMH20HVATNET): Tie the Primary

and Secondary Input cords to the Cable Retention Tray. Once

you’ve secured the two cords together and ensured that the

Secondary cord has a comfortable amount of slack, insert the

Secondary cord outlet into the IEC power inlet.

3. Features

18-09-500-933721.indb 9 10/4/2018 4:00:04 PM

Facility Circuit

PDUMH15ATNET

model shown.

Outlets may vary

by model.

Critical Equipment

Loads

Secondary UPS

Primary UPS

Primary Input Cord

Secondary Input Cord

Utility B

Utility A

10

4. Configuration and Operation

4.1 Automatic Transfer Switch

When the Primary and Secondary inputs are both connected to Tripp Lite UPS Systems, the PDU

operates as an Automatic Transfer Switch, providing redundant input power for high availability

applications. Under normal operating conditions, the PDU will distribute power from the Primary

input source, switching to the Secondary input source under certain conditions. The PDU will switch

to the Primary source whenever it is “Good” according to the PDU input voltage definitions (see

section 4.1.2 for more information).

4.1.1 Preferred Configuration

The Automatic Transfer Switch function provides increased availability when the Primary and

Secondary inputs of the PDU are connected to separate Tripp Lite UPS Systems that are connected

to separate utility power sources. For maximum availability, Tripp Lite recommends using matching

SmartOnline UPS Systems with pure sine wave output for the Primary and Secondary input power

sources. The automatic transfer switch function will be compromised if the primary and secondary

inputs are connected to the same utility power source.

Warning: DO NOT connect the primary input to a line-interactive UPS, due to transfer time

issues, or to any source that does not supply a pure sine wave. Such sources may be used

to power the secondary input.

18-09-500-933721.indb 10 10/4/2018 4:00:05 PM

11

4. Configuration and Operation

4.1.2 Automatic Transfer Switch Source Selection

The PDU will power up if one of the input sources is greater than the minimum startup voltage. In

normal operation (after power-up), if the presently selected source (primary or secondary) degrades

to a lesser condition, the unit should switch to the alternate source, if that source is of better

quality. The unit prefers the primary source, and will always switch to it in the event that both

sources are of the same (fair or good) quality. If the present source is becoming bad and the

alternate source is at least fair, the unit will switch to the alternate source.

Nominal Voltage of PDU

Low-Voltage Models High-Voltage Models

120V 200-208V 220-240V

Minimum Startup Voltage

85V 163V 163V

Good Voltage Range

99-139V 172-241V 190-266V

Fair Voltage Range

75-98V 144-171V 144-189V

Bad Voltage Range

0-74V 0-143V 0-143V

4.1.3 Quick Test

Primary Input Active

Secondary Input Active

After installing the PDU and connecting

equipment, you may test the Automatic

Transfer Switch function by temporarily shutting

down the UPS system connected to the

Primary AC input. When the Primary input UPS

is no longer supplying AC power, the PDU will

switch from the Primary input to the Secondary

input, and the Secondary input LED will

illuminate. When the Primary input UPS has

been restarted and resumes supplying AC

power, the PDU will switch back to the Primary

input.

Note: The primary and secondary inputs must be connected to separate sources of utility power. The automatic

transfer switch function will be compromised if the primary and secondary inputs are connected to the same

utility power source. Do not perform a test with equipment that must remain in productive operation. Any test

procedure must prepare for the contingency that the equipment may lose power. Do not test the PDU by

detaching power cords which are connected to live power sources, as this eliminates the connection to ground

and places your equipment at risk.

18-09-500-933721.indb 11 10/4/2018 4:00:05 PM

12

LIMITED WARRANTY

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in

material and workmanship for a period of 2 years (except internal UPS system batteries outside USA and Canada, 1 year)

from the date of initial purchase. If the product should prove defective in material or workmanship within that period,

Seller will repair or replace the product, in its sole discretion. Service under this Warranty can only be obtained by your

delivering or shipping the product (with all shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th Street,

Chicago, IL 60609 USA. Seller will pay return shipping charges. Visit www.tripplite.com/support before sending any

equipment back for repair.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR

NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN.

EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF

MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS

WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow

limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal

rights, and you may have other rights which vary from jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe

for the use intended. Since individual applications are subject to great variation, the manufacturer makes no

representation or warranty as to the suitability or fitness of these devices for any specific application.

PRODUCT REGISTRATION

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You'll be automatically entered into a drawing

for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

FCC Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense. The user must use shielded cables and

connectors with this product. Any changes or modifications to this product not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a

unique series number. The series number can be found on the product nameplate label, along with all required approval

markings and information. When requesting compliance information for this product, always refer to the series number.

The series number should not be confused with the marking name or model number of the product.

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

www.tripplite.com/support

E-mail: [email protected]

5. Technical Support

6. Warranty and Product Registration

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

18-09-500-933721.indb 12 10/4/2018 4:00:05 PM

1111 W. 35th Street, Chicago, IL 60609 EE. UU. • www.tripplite.com/support

13

Manual del Propietario

PDU para Rack Controlable,

con Medidor Digital con Switch

de Transferencia Automática

Modelos: PDUMH15AT, PDUMH15ATNET, PDUMH15HVAT,

PDUMH15HVATNET, PDUMH20AT, PDUMH20ATNET,

PDUMH20HVAT, PDUMH20HVATNET

Número de serie: AGAC7625

1. Instrucciones Importantes de Seguridad 14

2. Instalación 15

2.1 Instalación del PDU 15

2.2 Conexión del PDU 15

2.3 Conexión a Red del PDU 18

3. Características 19

4. Conﬁguración y Operación 22

4.1 Switch de Transferencia Automática 22

5. Soporte Técnico 24

6. Garantía 24

English 1

Français 25

Русский 37

18-09-500-933721.indb 13 10/4/2018 4:00:05 PM

14

CONSERVE ESTAS INSTRUCCIONES

• Este manual contiene instrucciones y advertencias que deben seguirse

durante la instalación, la operación y el almacenamiento de este

producto. El incumplimiento de estas instrucciones y advertencias

puede afectar la garantía del producto.

• Advertencia: Este equipo cumple con lo exigido para la Clase A del

CISPR 32. En un entorno residencial, este equipo puede ocasionar

una interferencia de radio.

• El PDU proporciona la conveniencia de múltiples tomacorrientes, pero NO ofrece protección

contra sobretensión o ruido en la línea para los equipos conectados.

• El PDU está diseñada solo para uso en interiores en un entorno controlado lejos de humedad

excesiva, temperaturas extremas, contaminantes conductivos, polvo o luz del sol directa.

• Mantiene la temperatura ambiente interior entre 0°C y 50°C (32°F y 122°F).

• El PDU debe ser instalado solamente por un técnico calificado.

• No intente instalar el PDU en una superficie inestable o no segura.

• Instale de acuerdo con los reglamentos eléctricos locales. Asegúrese de usar para la instalación

la protección adecuada contra sobrecorriente, de acuerdo con la especificación de la clavija o

del equipo.

• Conecte el PDU a un tomacorriente que esté de acuerdo a los códigos locales de construcción y

que esté correctamente protegido contra corrientes excesivas, cortocircuitos y fallas de conexión

a tierra.

• Los tomacorrientes eléctricos que suministran energía al equipo deben instalarse próximos al

equipo y ser fácilmente accesibles.

• No conecte El PDU a un toma corriente que no esté a tierra o cables de extensión o

adaptadores que eliminen la conexión a tierra.

• Asegúrese de proporcionar un dispositivo local de desconexión, que sea fácilmente accesible, en

cualquier modelo que esté instalado permanentemente sin una clavija.

• Nunca intente instalar equipos eléctricos durante una tormenta eléctrica.

• El equipo individual conectado al PDU no debe consumir más corriente que la de la

especificación de cada tomacorriente individual del PDU.

• La carga total conectada al PDU no debe exceder la capacidad de carga máxima del PDU.

• No intente modificar el PDU, las clavijas de entrada o los cables de alimentación.

• No perfore ni intente abrir ninguna parte del gabinete del PDU. No tiene partes a las que el

usuario pueda dar servicio.

• No intente usar el PDU si se daña cualquier parte.

• No se recomienda el uso de este equipo en aplicaciones de soporte de vida en donde la falla de

este equipo pueda consecuentemente causar la falla del equipo de soporte de vida o afectar

significativamente su seguridad o efectividad.

1. Instrucciones de Seguridad Importantes

18-09-500-933721.indb 14 10/4/2018 4:00:05 PM

PDUMH15HVAT, PDUMH15HVATNET

PDUMH20HVAT, PDUMH20HVATNET

PDUMH15HVATNET

15

Primary InputSecondary Input

9

Primary Input

Secondary Input

Unswitched

Outlets

2.2.1

PDUMH20AT

PDUMH20ATNET

PDUMH15AT

PDUMH15ATNET

PDUMH20HVAT

PDUMH20HVATNET

Entrada Primaria (Modelos de 120V) Entrada Primaria (Modelos de 208-240V)

2.1 Instalación del PDU

El PDU es compatible con configuraciones de

1U de rack .

Nota: Antes de la instalación, el usuario debe

determinar la conveniencia de los accesorios y los

procedimientos. El PDU y los accesorios incluidos

están diseñados para tipos comunes de racks y

gabinetes y pueden no ser apropiados para todas las

aplicaciones. Las configuraciones de instalación

exactas pueden variar.

Instalación en rack de 1U: Fije el PDU al

rack insertando los tornillos suministrados por

el usuario

A

a través de los soportes de

instalación

B

y dentro de los orificios del riel

del rack, tal como se muestra.

2. Instalación

B

A

2.2 Conexión del PDU

Todos los modelos de PDU incluyen una entrada de CA primaria y una secundaria (consulte el

diagrama). La tabla de referencia que aparece a continuación describe cada entrada primaria y

secundaria del modelo:

Modelo Entrada Primaria Entrada Secundaria*

PDUMH15AT NEMA 5-15P (cable ﬁjo) Entrada C14 IEC

PDUMH15ATNET NEMA 5-15P (cable ﬁjo) Entrada C14 IEC

PDUMH15HVAT Entrada C14 IEC (cable desprendible) Entrada C14 IEC

PDUMH15HVATNET Entrada C14 IEC (cable desprendible) Entrada C14 IEC

PDUMH20AT NEMA 5-15P (cable ﬁjo) Entrada C20 IEC

PDUMH20ATNET NEMA 5-15P (cable ﬁjo) Entrada C20 IEC

PDUMH20HVAT Entrada C20 IEC (cable desprendible) Entrada C20 IEC

PDUMH20HVATNET Entrada C20 IEC (cable desprendible) Entrada C20 IEC

Nota: El modelo PDUMH15HVATNET usa insertos de seguridad en las clavijas C13, para una conexión firme con

las entradas C14 primaria y secundaria.

PDUMH15AT, PDUMH15ATNET,

PDUMH20AT, PDUMH20ATNET

B

A

18-09-500-933721.indb 15 10/4/2018 4:00:07 PM

16

2.2.2 Para conectar el cable de

la entrada secundaria:

Forme un ojal con el cable Secundario

A

y

asegure la unión de ese ojal al cable Primario

B

con una banda de sujeción de plástico.

Asegúrese que la abrazadera de plástico esté

alrededor de los cables secundario y Primario,

así como a través del ojal creado en el cable

secundario

C

. (Vea el diagrama).

Nota: Deje espacio entre el ojal y el tomacorrientes

para que el cable quede lo más holgado posible.

En los modelos PDUMH20HVAT y

PDUMH20HVATNET, ambos cables deben estar

atados en la Bandeja de Retención de Cables.

(Vea el diagrama).

Una vez que ambos cables estén asegurados y

que el cable secundario quede lo

suficientemente holgado, inserte el

tomacorriente de este cable en la entrada de

energía IEC.

Nota: El modelo PDUMH15HVATNET usa insertos de

seguridad plug locks en las clavijas C13, para una

conexión firme con las entradas C14 primaria y

secundaria.

2.2.3 Conecte los Adaptadores

para Clavija de Entrada (Opcional -

Solo los modelos PDUMH20AT,

PDUMH20ATNET):

El PDU incluye dos adaptadores que convierten

una u otra de las clavijas de entrada L5-20P a

clavijas de entrada 5-20P. La conexión de los

adaptadores es opcional. El PDU funcionará

normalmente sin conectar los adaptadores.

2.2.4 Conecte el Cable de

Entrada Secundaria al PDU:

Aunque el PDU funcione sin conectar el cable

de entrada secundaria, dicha entrada es

necesaria para la función del Switch de

Transferencia Automática del PDU.

2. Instalación

Entrada primariaEntrada secundaria

9

2.2.2

2.2.3

2.2.4

PDUMH20AT,

PDUMH20ATNET

PDUMH20AT,

PDUMH20ATNET

PDUMH15HVAT, PDUMH15HVATNET

PDUMH15AT,

PDUMH15ATNET

A

B

C

18-09-500-933721.indb 16 10/4/2018 4:00:08 PM

Primary Input

Secondary Input

Unswitched

Outlets

PDUMH20AT,

PDUMH20ATNET

PDUMH20HVAT,

PDUMH20HVATNET

PDUMH15HVAT,

PDUMH15HVATNET

PDUMH15AT,

PDUMH15ATNET

2.2.6

A

17

2. Instalación

2.2.5

C13-C14 (Modelos:

PDUMH15HVAT y PDUMH15HVATNET)

o Cables C19-C20 (solo los modelos

PDUMH20HVAT y PDUMH20HVATNET):

El PDU incluye un cable de interconexión C13

a C14 (PDUMH15HVAT/NET) o dos cables de

interconexión C19 a C20 (PDUMH20HVAT/

NET) para las dos entradas primaria y

secundaria, que pueden usarse para conectar a

las fuentes de UPS contra-corriente. De forma

alternativa, el usuario puede suministrar cables

IEC con clavijas específicas según el país.

Primary Input

Secondary Input

Unswitched

Outlets

Entrada primariaEntrada secundaria

9

2.2.5

PDUMH20HVAT, PDUMH20HVATNET

PDUMH15HVAT, PDUMH15HVATNET

2.2.6 Conecte las Clavijas de Entrada del PDU:

(Consulte la sección de Configuración y Operación para obtener más datos). Conecte la clavija

de entrada Primaria

A

a una fuente preferida de alimentación de CA de 120V/230V conectada a

tierra, como un Sistema UPS SmartOnline

®

. El sistema UPS no debe compartir un circuito con una

carga eléctrica pesada (como un aire acondicionado o refrigerador). Bajo condiciones de operación

normales, el PDU distribuirá la alimentación de CA desde la fuente de entrada primaria. Conecte la

clavija de entrada secundario

B

a una fuente alternativa de alimentación de CA 120V/230V

puesta a tierra, como un sistema UPS redundante SmartOnline.

No enchufe la entrada secundaria

en la misma fuente de alimentación que la entrada primaria. El PDU distribuirá la alimentación de CA

desde la entrada secundaria solo si la entrada primaria no está disponible.

Nota: Inmediatamente después de conectar el PDU a una alimentación de CA, notará una serie de chasquidos

suaves emitidos por relés eléctricos dentro del PDU. Los relés pueden emitir sonidos ocasionalmente durante la

operación del PDU. Esto es normal.

B

A

18-09-500-933721.indb 17 10/4/2018 4:00:09 PM

RESET

STATUS

CONFIG

RESET

STATUS

CONFIG

Primary Input

Secondary Input

Unswitched

Outlets

Primary InputSecondary Input

9

2.2.8

PDUMH20AT

PDUMH20HVAT, PDUMH20HVATNET

PDUMH15HVAT, PDUMH15HVATNET

PDUMH15AT

PDUMH20ATNET

PDUMH15ATNET

18

2. Instalación

2.2.7

Selección del Rango de Voltaje de Entrada (opcional: solo los

modelos PDUMH15HVAT, PDUMH15HVATNET, PDUMH20HVAT y

PDUMNH20HVATNET):

Estos modelos tienen dos rangos de voltaje de entrada nominales: 200V-208V (“LO”) y

220V-240V (“HI”). Presione el switch junto a la pantalla para cambiar la configuración de voltaje

nominal al rango deseado “HI” o “LO”. Esta configuración ajusta los rangos de voltaje para las

entradas primaria y secundaria. La pantalla indicará “HI” o “LO” durante cinco segundos.

2.2.8 Conecte el Equipo al PDU:

No exceda el valor nominal de carga del PDU. La corriente eléctrica total utilizada por el PDU

aparecerá en el medidor digital en amperes. Cada tomacorriente incluye un LED verde que se

ilumina cuando el tomacorriente recibe alimentación de CA.

2.3 Conexión a red del PDU

Para obtener instrucciones de configuración de red, consulte el Manual del Propietario de

la tarjeta WEBCARDLX incluido con este producto.

18-09-500-933721.indb 18 10/4/2018 4:00:10 PM

*Solo modelos NET.

19

3. Características

3

5

3 4 2 1

6

6 8

1 2 3

6

PDUMH20AT, PDUMH20ATNET

PDUMH15AT, PDUMH15ATNET

PDUMH15HVAT, PDUMH15HVATNET

PDUMH20HVAT, PDUMH20HVATNET

3

5

1 2

6

7

2

6

14

18-09-500-933721.indb 19 10/4/2018 4:00:11 PM

20

3. Características

1

Entrada Primaria

Modelos PDUMH15AT/NET: El cable está sujeto de forma fija al PDU y tiene una clavija NEMA

5-15P.

Modelos PDUMH15HVAT/NET: El cable C13-C14 se puede desprender.

Modelos PDUMH20AT/NET: El cable está sujeto de forma fija al PDU y tiene una clavija

NEMA L5-20P.

Modelos PDUMH20HVAT/NET:El cable C19-C20 se puede desprender.

2

Entrada Secundaria (desprendible en todos los modelos)

Modelos PDUMH15AT/NET, PDUMH15HVATNET: La entrada IEC-320-C14 se conecta con el

cable de entrada de alimentación de CA Secundario desprendible.

Modelos PDUMH20AT/NET, PDUMH20HVAT/NET: La entrada IEC-320-C20 se conecta con el

cable de entrada de alimentación de CA Secundario desprendible.

3

Tomacorrientes Controlables: Durante la operación normal, los tomacorrientes distribuyen

energía CA a los equipos conectados. En los modelos PDUMH15ATNET, PDUMH15HVATNET,

PDUMH20ATNET y PDUMH20HVATNET, los tomacorrientes NEMA 5-15R, NEMA 5-15/20R e

IEC-320-C13 pueden encenderse y apagarse mediante un control por software. Cuando un

tomacorriente está encendido, el LED asociado se ilumina.

4

Tomacorrientes siempre encendidos [Unswitched] (Modelos PDUMH15HVAT/NET,

PDUMH20HVAT/NET): Estos tomacorrientes reciben energía de cualquier fuente de entrada,

pero no se controlan individualmente.

5

Puerto de Configuración de Fábrica: El puerto está reservado para configuración solo por

parte del personal autorizado de fábrica. No hay disponible información para el usuario. La

conexión a este puerto puede hacer que la unidad se vuelva inoperable y anular su garantía.

6

Medidor de Carga Digital (Amperímetro): La corriente eléctrica total usada por los equipos

conectados se muestra en el medidor digital en amperes.

Switch de Selección de Rango de Voltaje de Entrada (Modelos PDUMH15HVATNET,

PDUMH20HVATNET): El switch en la parte inferior izquierdo de la pantalla se puede usar para

cambiar entre los rangos de voltaje “HI” o “LO”. La pantalla indicará “HI” o “LO” durante cinco

segundos. Oprima el switch una vez para mostrar los rangos, oprima nuevamente dentro de los

cinco segundos posteriores para cambiar los parámetros. Las configuraciones también pueden

cambiarse mediante PowerAlert (solo PDUMH15HVATNET y PDUMH20HVATNET).

Pantalla de Dirección IP (Modelos PDUMH15HVATNET, PDUMH20HVAT/NET): Oprima y

mantenga oprimido el switch para mostrar la dirección IP de la tarjeta SNMP en el PDU.

7

Interfaz de Red (Modelos PDUMH15ATNET, PDUMH15HVATNET, PDUMH20ATNET y

PDUMH20HVATNET): Le permite operar el PDU como un dispositivo de red, accesible a través

de la plataforma de administración de red SNMP, explorador de red, SSH o Telnet.

8

Indicador de Fuente de Entrada: Cuando el PDU está conectado a una fuente de

alimentación de CA viva, el LED de entrada Primaria o Secundaria se ilumina para indicar qué

fuente está suministrando energía a los tomacorrientes.

18-09-500-933721.indb 20 10/4/2018 4:00:11 PM

Страница загружается...

Tripp Lite Switched/Metered Rack PDU Инструкция по применению

Похожие модели бренда