Panasonic DMW-MCTZ30E Lumix Инструкция по применению

Operating Instructions

Manuel d’utilisation

Bedienungsanleitung

Instrucciones de funcionamiento

Istruzioni d’uso

使用說明書

使用说明书

Инструкция по эксплуатации

Marine Case

Boîtier marin

防水盒

DMW-MCTZ30

VQT4C30

F0112KD0

Before connecting, operating or adjusting this product, please read the

instructions completely.

Avant de raccorder, régler ou utiliser l’appareil, il est recommandé de lire

attentivement le manuel d’utilisation.

Bitte lesen Sie diese Bedienungsanleitung vor der Inbetriebnahme des

Gerätes vollständig durch.

Antes del uso, lea completamente estas instrucciones.

Leggere completamente queste istruzioni prima dell’uso.

使用前，請完整閱讀本說明書。

使用前，请完整阅读本说明书。

Перед пользованием прочтите, пожалуйста, эту инструкцию полностью.

E

PP

Model No.

N

o

de modèle

型号

until

2012/2/16

COVER.fm 1 ページ２０１２年１月１２日　木曜日　午前１１時３８分

2

VQT4C30

Contents

Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Handling and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

What is the O-ring?. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Preparation -Setting the O-ring- . . . . . . . . . . . . . . . . . 10

Preparation -Checking the Case is Waterproof- . . . . . 14

Preparation -Attaching the Digital Camera- . . . . . . . . 15

Taking Pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Tips for Taking Pictures in the Water . . . . . . . . . . . . . 19

After Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Cleaning and Storing . . . . . . . . . . . . . . . . . . . . . . . . . 21

Caution for Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Getting Started

Preparation

Operation

Others

DMW-MCTZ30-VQT4C30.book 2 ページ２０１２年１月１２日　木曜日　午前１０時５０分

3

VQT4C30

Before Use

≥ This Marine Case is designed for a Panasonic Digital Camera.

You can enjoy taking pictures underwater at depths up to 40 m/130 feet.

≥ In the case of water leakage due to insufficient care, Panasonic is in no

way liable for damage to any products (digital camera, batteries, card etc.)

inside this Case, photography costs or any other expenses.

≥ Panasonic also offers no compensation for accidents resulting in injury or

damage to property.

≥ Read the operating instructions for your digital camera.

≥ Before attaching the digital camera, submerge the case in water for

about 3 minutes or more to check that there is no water leakage.

∫ About handling this Case

≥ Use under the following conditions.

• Water depth: Up to 40 m/130 feet

• Ambient temperature: 0 °C

to

40 °C/32 °F

to

104 °F

≥ Do not use the Case in water over 40 °C/104 °F. The heat may damage the Case or

cause water leakage.

≥ The Case is made of impact resistant polycarbonate however be careful when you

are using it. It can be easily scratched when taking pictures in rocky places etc. and

can be damaged by the impact if dropped etc. When travelling, pack the Case

carefully to prevent any direct impact if it is dropped etc. and do not leave the digital

camera in the Case. Only attach the digital camera to the case if you are

transporting it a short distance such as from the airport to the diving spot. (You

cannot reuse the material the Case was packed in at the time of purchase to

transport it.)

≥ When boarding a plane, the change in atmospheric pressure may cause the inside

of the Case to expand causing damage to the Case. Remove the O-ring before

boarding a plane.

Insert the removed O-ring into the supplied exclusive polyester bag.

≥ Do not leave the digital camera in the Case for a long period of time in a car, a

ship, exposed to direct sunlight etc. The Case is an airtight device so the

temperature inside the Case will become very high and the digital camera may

stop operating properly. Do not let the temperature inside the Case become

too high.

ENGLISH

DMW-MCTZ30-VQT4C30.book 3 ページ２０１２年１月１２日　木曜日　午前１０時５０分

4

VQT4C30

Before Use (continued)

∫ Using the Case in high or low temperatures

≥ If you open or close the Case where it is humid or hot and then move to a place that

is cold or dive underwater, condensation may appear inside the Case, the glass

surface may become cloudy and the digital camera may be damaged.

≥ If you suddenly move the Case from a cold place or cold water to a warm place, the

glass surface may become cloudy. Wait until the Case becomes close to the air

temperature before taking pictures.

∫ About preparation

≥ Do not open or close the Case where it may be splashed by water or sand may

get in it. We recommend opening or closing the Case indoors.

≥ Replace the battery, card etc. and attach the digital camera indoors where there is

little moisture.

≥ If you must open or close the Case at the diving spot to replace the battery or

the card, be sure to follow the steps below.

• Select a place where the Case will not be splashed by water and sand will not get

in it.

• Blow off any drops of water in the gap between the rear case and the front case

and on the buckle. Thoroughly wipe off any remaining drops of water with a dry

cloth.

• Thoroughly wipe off any drops of water on your body or hair.

• Be particularly careful about any water coming from the sleeves of your thermal

suit.

• Do not touch the digital camera if your hands are wet from sea water. Wet a towel

with fresh water and place it in a polyester bag beforehand. Use this towel to wipe

off any drops of water or sand on your hands or body.

≥ This Case does not absorb shock. If you place a heavy object on the Case or cause

shock to it, the digital camera may be damaged. Be careful when you are using the

case.

DMW-MCTZ30-VQT4C30.book 4 ページ２０１２年１月１２日　木曜日　午前１０時５０分

5

VQT4C30

Accessories

When you first open the package, check that the Case and all the

accessories are included and that there has been no damage to the

Case or any of the accessories during distribution or

transportation. If you find something unusual, consult your dealer

before using the Case.

Do not use any accessories except those specified below.

Replacement O-ring

VMG1798

* In exclusive

polyester bag

* One has been

attached to the unit

in advance.

Silica Gel (Desiccant)

(1 g/5 pieces)

VZG0371

Grease (for O-ring)

VZG0372

Hand Strap

VFC4190

Weight (2), Weights attachment screw

VXA8847

Diffuser/String

VYK5S28

≥ You can remove this diffuser when not using it

.

Removing Attaching

Align with the mark on the back of the

case and attach.

DMW-MCTZ30-VQT4C30.book 5 ページ２０１２年１月１２日　木曜日　午前１０時５０分

6

VQT4C30

Handling and Care

≥

Do not place the Case where it may fall.

• If the Case falls on your head or foot, it will injure you and cause the Case to

malfunction.

≥

Never alter the Case.

• If water leaks into the digital camera because the Case was altered, the digital

camera may be damaged beyond repair.

• If you continue to use the digital camera after water has leaked into it, this may

cause a fire.

≥

Do not use the Case while scuba diving without proper training.

• You should only operate the Case while scuba diving if you have been properly

trained and certified for this sport.

≥

Never place the Case, grease, silica gel or O-ring within the reach of

infants.

• If any part of an infant’s body is caught in the Case, it may cause an injury.

• Infants may accidentally swallow the grease, silica gel or O-ring.

• Consult a doctor immediately if you think an infant may have swallowed the

grease, silica gel or O-ring.

≥

Do not hang the strap around your neck underwater.

• It may become wound around your neck causing suffocation or other serious

injuries.

≥

Thoroughly wash any grease on your hands.

• Do not allow the grease on your hands to come into contact with your mouth or

eyes.

≥

If water leaks into the case, stop using it immediately.

• This may cause an electric shock, burning or a fire.

• Consult your dealer.

≥

If anything abnormal occurs while using the Case underwater, please

follow all necessary procedures and guidelines for decompressing

when you ascend.

• If you ascend too quickly, you may get caisson disease.

≥

If smoke or abnormal heat, smells or sounds come from the Case,

stop using it immediately.

• These may cause an electric shock, burning or fire.

• Remove the digital camera from the Case and then immediately remove the

battery from the digital camera.

• Consult your dealer.

≥

Be careful when opening the Case after water leakage.

• The leaked water may blow out or the rear case may flip.

DMW-MCTZ30-VQT4C30.book 6 ページ２０１２年１月１２日　木曜日　午前１０時５０分

7

VQT4C30

≥ Do not leave the Case where the temperature is high.

• The temperature inside the Case becomes very high particularly when it is

exposed to direct sunlight on a beach, a ship etc. or when it is left in an airtight car

in the summer. The heat may damage the Case or its inner parts.

• If a digital camera is attached to the Case, it may also be damaged.

• If you use the attached digital camera when the temperature inside the Case is

very high, it may cause leakage, short-circuiting or insulation failure resulting in

fire or malfunction.

≥ Do not handle the digital camera or the battery with wet hands.

• This may cause an electric shock or malfunction.

∫ When taking pictures with the flash

≥ When taking pictures with the flash, the corners of the picture may be vignetted or

the picture may not be lit evenly.

≥ When taking pictures with the flash, the available flash range is less underwater

than on land.

DMW-MCTZ30-VQT4C30.book 7 ページ２０１２年１月１２日　木曜日　午前１０時５０分

8

VQT4C30

Components

1. Zoom Lever

2. Motion Picture Button

¢1

3. Shutter Button

4. Mode dial

5. Mounting shoe for INON

Inc., external strobe

¢2

6. Front Case

7. Diffuser (supplied)

8. Front Glass

9. Camera ON/OFF Switch

10. [Rec]/[Playback] selector

switch

11. Button operation section

(Read the operating

instructions of the digital

camera for details about

each button operation.)

12. Rear Case

13. Buckle

14. Lock Release Lever

15. Strap Eyelet

(for attaching the supplied hand

strap and diffuser)

42 3 516

14

15

8

9

7

10

11

12

13

¢1 Functions vary depending on the digital camera being used, so follow the

indication on the the digital camera.

¢2 This is a mounting shoe dedicated for an external strobe manufactured by

INON Inc.

Please refer to INON Inc. regarding compatible strobe.

http://www.inon.co.jp/INON_WORLD_body.html

DMW-MCTZ30-VQT4C30.book 8 ページ２０１２年１月１２日　木曜日　午前１０時５０分

9

VQT4C30

What is the O-ring?

≥ The O-ring is a waterproofing packing used for underwater cameras, watches and

diving equipment.

≥ The O-ring keeps the Case waterproof by sealing the gap between the rear case

and the front case.

∫ How the O-ring keeps the Case waterproof

The gum comes into contact with the sides of the Case making the

Case waterproof and stopping water from entering from the gap.

When water pressure acts on the O-ring, the surface of the O-ring

expands and the Case is sealed more tightly.

The O-ring prevents water leakage by coming into uniform

contact with the sides of the Case. Therefore, good care of the

O-ring is very important. Incorrect care of the O-ring may

cause water leakage.

O-ring

Digital Camera

Front Case

Rear Case

O-ring

DMW-MCTZ30-VQT4C30.book 9 ページ２０１２年１月１２日　木曜日　午前１０時５０分

10

VQT4C30

Preparation -Setting the O-ring-

Be sure to set the O-ring before attaching a digital camera.

Thoroughly wash and dry your hands before handling the O-ring. Place

the O-ring where there is no sand or dust.

1

Loosen the O-ring with your fingers to remove it.

≥ Loosen part of the O-ring with the tips of two fingers and then lift the loosened

part. Be careful not to scratch the O-ring with your fingernails.

∫

Note

≥ Do not use a pointed object to remove the O-ring. This may scratch or damage the

O-ring.

O-ring

DMW-MCTZ30-VQT4C30.book 10 ページ２０１２年１月１２日　木曜日　午前１０時５０分

11

VQT4C30

2

Check the O-ring.

≥ Check that there is no dirt, sand, hair, dust, salt crystals, lint or grease on the

O-ring. If you find any of these, remove them with a soft, dry cloth.

≥ There may be dirt on the O-ring that you cannot see. Check if there is any dirt by

rubbing your finger over the O-ring.

≥ Be careful not to leave any fibers from the dry cloth on the O-ring when wiping it.

≥ Check that the O-ring is not ripped, twisted, squashed, frayed or scratched and

that there is no sand sticking to it. Replace the O-ring in these cases.

3

Inspect the O-ring groove.

≥ Grains of sand or hardened salt crystals may get into the O-ring groove.

Remove them carefully with an air spray or a cotton swab. If you use a cotton

swab, be careful not to leave any fibers from it in the O-ring groove.

≥ Inspect the front case groove as well as the rear case (side where O-ring is set)

groove.

3Dirt

3Sand

3Hair

3Dust 3Salt

crystals

3Lint

3Ripped

3Twisted

3

Squashed

3Frayed 3

Scratched

3Sand

DMW-MCTZ30-VQT4C30.book 11 ページ２０１２年１月１２日　木曜日　午前１０時５０分

12

VQT4C30

Preparation -Setting the O-ring- (continued)

4

Apply the grease (supplied).

Apply O-ring grease to clean the surface of the O-ring and replenish the oil.

≥ Apply a rice-grain size of grease (supplied) evenly to the O-ring with the tip of

your finger. (Do not apply the grease with paper or a cloth. The fibers from the

paper or cloth may stick to the O-ring.)

≥ If there is too much grease on the O-ring, dirt and dust will stick to it causing

water to leak in. Therefore, hold the O-ring between the balls of your finger and

thumb and gently remove excess grease.

≥ By applying the O-ring grease thinly and evenly, the O-ring fits flexibly to the

groove of the marine case and keeps it airtight.

≥

The surface of the O-ring may stretch or rip, causing a water leak, when an

O-ring grease other than supplied is used, so always use the specified O-

ring grease.

5

Fit the O-ring evenly into the O-ring groove.

Check the following:

≥ There is no dirt sticking to the O-ring.

≥ The O-ring has not come out.

≥ The O-ring is not twisted.

≥ The O-ring is not stretched too much.

CORRECT

INCORRECT

DMW-MCTZ30-VQT4C30.book 12 ページ２０１２年１月１２日　木曜日　午前１０時５０分

13

VQT4C30

6

Inspect the O-ring one last time.

Check the following one more time:

≥ There is no dirt sticking to the O-ring.

≥ The O-ring has not come out.

≥ The O-ring is not twisted.

≥ There are no scratches or squashed parts on the O-ring.

Thoroughly wipe any grease off your hands with a dry cloth. Afterwards

wash thoroughly with fresh water.

7

Close the buckle.

≥ Check that no foreign materials are sticking to the outer surface of the O-ring or

the buckle on the front case and then close the Case.

∫

Notes

≥ To keep the Case completely airtight, do not scratch the surface of the O-ring that

comes into contact with the sides of the Case.

≥ Never use an O-ring that has been scratched or damaged by dirt etc. This will cause

water leakage.

≥ Each time you use the Case, remove the O-ring and check that there is no dirt,

sand, hair or other foreign materials in the O-ring groove and then apply a thin coat

of grease (supplied). If you apply too much grease, dirt and the dust may stick to the

O-ring causing water leakage.

≥ Be sure to bring a spare O-ring in case the O-ring that you are using becomes

damaged or scratched.





DMW-MCTZ30-VQT4C30.book 13 ページ２０１２年１月１２日　木曜日　午前１０時５０分

14

VQT4C30

Preparation -Checking the Case is Waterproof-

After setting the O-ring, check that no water leaks into the Case by

submerging it in a water tank, bath tub etc. for about 3 minutes before

attaching a digital camera.

≥ Do not use the Case in water over 40 °C/104 °F. The heat may damage the Case or

cause water leakage.

‘

Carry out the same test after attaching the digital camera to the Case. (P15)

∫

Notes

≥ If bubbles rise from the Case when it is submerged in water or there is water inside

the Case when you take it out of the water, there is water leakage. In these cases,

consult your dealer.

≥ If water leaks into the Case while you are using it and the digital camera is

submerged in water, remove the battery immediately. Hydrogen gas can cause

burning or explosion if there is a fire nearby.

≥ If you dive quickly while holding the Case or throw the Case from a ship into the sea,

some water leakage may occur because of high pressure. This is not a malfunction

of the Case. Always dive slowly into the water.

≥ The Case is designed to be used at a depth of up to 40 m/130 feet. If you dive

deeper than 40 m/130 feet, part of the Case may be damaged beyond repair.

≥ When closing the Case, be careful that no foreign materials get caught between the

O-ring and the O-ring groove. Even one strand of hair or one grain of sand can

cause water leakage.

DMW-MCTZ30-VQT4C30.book 14 ページ２０１２年１月１２日　木曜日　午前１０時５０分

15

VQT4C30

Preparation -Attaching the Digital Camera-

Read the notes on page 17 before attaching the digital camera.

Check that the ON/OFF Switch on the camera and the case is set to

[OFF], and [Rec]/[Playback] selector switch is set to [

!

].

≥ Remove the strap from the digital camera.

1

Push

2

up with your finger while sliding

1

to open the buckle.

2

Attach the digital camera to the Case.

≥ Be careful not to catch the shading hood 1.

3

Insert the silica gel (supplied).

≥ Always use new silica gel.

Silica gel

Digital Camera

DMW-MCTZ30-VQT4C30.book 15 ページ２０１２年１月１２日　木曜日　午前１０時５０分

16

VQT4C30

Preparation -Attaching the Digital Camera- (continued)

≥ When inserting the silica gel, bend it as shown in the illustration below

and then insert it as far as possible. If you close the Case with the silica

gel not fully inserted, the silica gel will get caught in the O-ring causing

water leakage.

≥ If the air temperature is high and the water temperature is low, condensation

may appear inside the Case. To prevent condensation, insert silica gel

(supplied) inside the Case in advance. To prevent the Case from becoming

fogged up, insert the silica gel about 1 to 2 hours before using the Case.

4 Close the buckle.

‘

Check that the buckle is closed firmly.

Do not insert the strap etc. in the buckle.

5 After you have attached the digital camera, check one more time that

no water leaks into the Case. (P14)

Silica gel





DMW-MCTZ30-VQT4C30.book 16 ページ２０１２年１月１２日　木曜日　午前１０時５０分

17

VQT4C30

∫ Notes

≥

Be careful not to get the shading hood dirty with fingerprints etc.

≥ Check one more time that the O-ring is fitted evenly into the O-ring groove.

≥ Avoid opening or closing the Case where there is a lot of sand or dust and in humid

or wet places.

≥ If there is a sudden change of humidity caused by moist air entering the Case,

condensation may appear inside the Case.

≥ To prevent condensation, set the digital camera in as dry a place as possible. Also,

check that the silica gel (supplied) is sufficiently dry before inserting.

≥ If sunscreen or suntan oil sticks to the Case, wash it off immediately with lukewarm

water to prevent reduced waterproofness or discoloration.

∫ Attaching the weights

About using the weights

Attach the weights to adjust to the preferred buoyancy when using the marine case.

Use them as necessary.

Refer to the following about buoyancy underwater.

1 If you use the digital camera and the marine case only:

They will float slowly in fresh water or seawater. (Plus buoyancy)

2 If you use the digital camera, the marine case and 1 weight:

They will float even more slowly in fresh water or seawater than

1.

(Plus buoyancy)

3 If you use the digital camera, the marine case and 2 weights:

They will sink slowly in fresh water or seawater. (Minus buoyancy)

How to attach the weights

If you use 1 weight, align the protruding part of

the weight with the tripod receptacle on the

marine case and then using a slotted screwdriver

or similar, use the supplied weights attachment

screw to attach to the tripod receptacle.

If you use 2 weights, align the projecting part of

the second weight with the indented part of the

first weight so that the weights do not overlap and

then attach them to the tripod receptacle.

If a digital camera with GPS function is attached to the marine case, failure of

positioning or other major errors may occur due to interference in the reception of

radio waves from the GPS satellite.

DMW-MCTZ30-VQT4C30.book 17 ページ２０１２年１月１２日　木曜日　午前１０時５０分

18

VQT4C30

Taking Pictures

∫

Be sure to check the following before entering the water

Check the following before diving.

≥ Is there sufficient remaining battery power?

≥ Is there sufficient memory in the card?

≥ Is the O-ring fitted evenly into the O-ring groove?

≥ Have you checked that no water leaks into the Case?

≥ Is the buckle closed firmly?

∫

Taking pictures

1

Turn the camera on.

2

Display the scene mode menu and then set [Underwater].

3

Aim the AF area on the LCD monitor at the subject you want to focus

on.

4

Fix the focus and take the picture.

∫

Notes

≥ Before attaching the camera to the Case, we recommend setting the clock again.

(Read the operating instructions of the digital camera for details.)

≥ If there are any particles floating in front of the camera, it may focus on them instead

of the subject.

≥ If there are drops of water or dirt sticking to the front glass, you may not be able to

focus properly. Be sure to wipe the front glass before taking pictures.

For details of [Underwater] setting or fixing the focus, refer to the operating

instructions of the digital camera.

ON

OFF





ON

OFF

Press 1 to release the lock

and then set to [ON].

Press 2 to lock.

DMW-MCTZ30-VQT4C30.book 18 ページ２０１２年１月１２日　木曜日　午前１０時５０分

19

VQT4C30

Tips for Taking Pictures in the Water

It is recommended to use the scene mode (underwater) appropriate for underwater

when recording underwater.

It may not be possible to record images with intended brightness or color depending on

the recording conditions (depth/weather/subject), so try using following functions

together.

It is recommended to use burst function to record subject that is moving fast, etc.

∫ Note

≥

For details of white balance fine adjustment (underwater mode) or other functions,

refer to the operating instructions of the digital camera.

Color is reddish, bluish

White balance fine adjustment

(Underwater Mode)

≥ This can adjust the red or blue tone.

Too bright/too dark

Exposure compensation

(For models with an Exposure

Compensation Function)

≥ This can adjust the brightness.

Auto bracket function

(For models with an Auto Bracket Function)

≥ This can record multiple images with

different exposure at once.

DMW-MCTZ30-VQT4C30.book 19 ページ２０１２年１月１２日　木曜日　午前１０時５０分

20

VQT4C30

After Use

After you have finished taking pictures, follow the steps below.

1

Submerge the Case in fresh water for about 30 minutes or more

without removing the digital camera to remove any salt crystals etc.

≥

Press all the operation buttons etc. on the Case to wash away any

seawater. If the salt crystals are not removed from the buttons etc., they

will harden and the buttons will become inoperable.

≥

Do not wash the Case with fast-running or pressurized water etc. as it may

cause water leakage.

2

Wipe the water with a dry cloth that has no salt crystals sticking to it

and then dry the Case completely.

≥ Do not dry the Case by exposing it to direct sunlight. This may

discolor

or

damage the Case or may hasten deterioration of the O-ring.

3

Open the rear of the case to remove the digital camera.

4

Remove the O-ring from the Case and check that there is no dirt etc.

in the O-ring groove.

5

Check that there are no scratches etc. on the O-ring while you are

applying the grease.

DMW-MCTZ30-VQT4C30.book 20 ページ２０１２年１月１２日　木曜日　午前１０時５０分

Страница загружается ...

Panasonic DMW-MCTZ30E Lumix Инструкция по применению

Panasonic DMW-MCTZ30E Lumix Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов