English
Refrigerator
user manual
imagine the possibilities
Thank you for purchasing a Samsung product.
Free Standing Appliance
This manual is made with 100% recycled paper.
DA99-03957C-06.indb 1 2015. 5. 7. �� 3:51
02_ safety information
SAFETY INFORMATION
• Before operating the appliance, please read this
manual thoroughly and retain it at a safe place
near the appliance for your future reference.
• Use this appliance only for its intended purpose
as described in this instruction manual. This
appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible
for their safety.
• This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Warnings and Important Safety Instructions in
this manual do not cover all possible conditions
and situations that may occur. It is your
responsibility to use common sense, caution,
and care when installing, maintaining, and
operating your appliance.
• Because these following operating instructions
cover various models, the characteristics of
your refrigerator may differ slightly from those
described in this manual and not all warning
signs may be applicable. If you have any
questions or concerns, contact your nearest
service center or find help and information
online at www.samsung.com
Important safety symbols and precautions :
WARNING
Hazards or unsafe practices that may result in
severe personal injury or death.
CAUTION
Hazards or unsafe practices that may result in
minor personal injury or property damage.
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions carefully.
Unplug the power plug from the wall socket.
Make sure the machine is grounded to prevent
electric shock.
Call the contact center for help.
Note.
These warning signs are here to prevent injury
to you and others.
Please follow them carefully.
After reading this section, keep it in a safe
place for future reference.
CE Notice
This product has been determined to be in
compliance with the Low Voltage Directive
(2006/95/EC), the Electromagnetic Compatibility
Directive (2004/108/EC), RoHS Directive
(2011/65/EU), Commission Delegated Regulation
(EU) No 1060/2010 and the Eco-Design
Directive(2009/125/EC) implemented by Regulation
(EC) No 643/2009 of the European Union. (For
products sold in European Countries only)
SEVERE WARNING SIGNS FOR
TRANSPORTATION AND SITE
• When transporting and installing the
appliance,care should be taken to ensure
that no parts of the refrigerating circuit
are damaged.
• R-600a or R-134a is used as a refrigerant.
Check the compressor label on the rear of
the appliance or the rating label inside the
refrigerator to see which refrigerant is used for
your refrigerator.
• When this product contains flammable gas
(Refrigerant R-600a),
- Refrigerant leaking from the pipe work could
ignite or cause an eye injury. If a leak is
detected, avoid any naked flames or potential
sources of ignition and air the room in which the
appliance is standing for several minutes.
- In order to avoid the creation of a flammable
gas-air mixture if a leak in the refrigerating
circuit occurs, the size of the room in which the
appliance may be sited depends on the amount
of refrigerant used.
WARNING
Safety information
DA99-03957C-06.indb 2 2015. 5. 7. �� 3:51
safety information _03
- Never start up an appliance showing any signs
of damage. If in doubt, consult your dealer.
The room where the refrigerator will be sited
must be 1m³ in size for every 8g of R-600a
refrigerant inside the appliance. The amount of
refrigerant in your particular appliance is shown
on the identification plate inside the appliance.
- If the appliance contains isobutane refrigerant
(R-600a), a natural gas with high environmental
compatibility that is, however, also combustible.
When transporting and installing the appliance,
care should be taken to ensure that no parts of
the refrigerating circuit are damaged.
SEVERE WARNING SIGNS FOR
INSTALLATION
• Do not install this appliance in a humid, oily
or dusty location, in a location exposed to
direct sunlight and water (rain drops).
- Deteriorated insulation of electrical parts may
cause an electric shock or fire.
• Do not place this refrigerator in direct sunlight or
expose to the heat from stoves, room heaters
or other appliances.
• Do not plug several appliances into the same
multiple power board.
The refrigerator should always be plugged into
its own individual electrical outlet which has a
voltage rating that matched the rating plate.
- This provides the best performance and
also prevents overloading house wiring
circuits, which could cause a fire hazard from
overheated wires. If the wall socket is loose, do
not insert the power plug.
- There is a risk of electric shock or fire.
• Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
• Do not bend the power cord excessively or
place heavy articles on it.
• Do not use aerosols near the refrigerator.
- Aerosols used near the refrigerator may cause
an explosion or fire.
• Do not install this appliance in a location where
gas may leak.
- This may result in an electric shock or fire.
• The installation or any service of this
appliance is recommended by a qualified
technician or service company.
- Failing to do so may result in an electric shock,
fire, explosion, problems with the product, or
injury.
• This refrigerator must be properly installed and
WARNING
located in accordance with the manual before it
is used.
• Connect the power plug in proper position with
the cord hanging down.
- If you connect the power plug upside down,
wire can get cut off and a cause fire or an
electric shock.
• Make sure that the power plug is not squashed
or damaged by the back of the refrigerator.
• When moving the refrigerator, be careful not to
roll over or damage the power cord.
- This constitutes a fire hazard.
• The appliance must be positioned so that the
plug is accessible after installation.
• The refrigerator must be grounded.
- You must ground the refrigerator to
prevent any power leakages or electric
shocks caused by current leakage from
the refrigerator.
• Never use gas pipes, telephone lines or other
potential lightening rods as ground.
- Improper use of the ground plug can result in
an electric shock.
• If the power cord is damaged,
have it replaced immediately by the
manufacturer or its service agent.
• The fuse on the refrigerator must be changed
by a qualified technician or service company.
- Failing to do so may result in an electric shock
or personal injury.
CAUTION SIGNS FOR
INSTALLATION
• Keep ventilation opening in the appliance
enclosure or mounting structure clear of
obstruction.
• Allow the appliance to stand for 2 hours after
installation.
SEVERE WARNING SIGNS FOR
USING
• Do not insert the power plug with wet
hands.
• Do not store articles on the top of the
appliance.
- When you open or close the door, the articles
may fall and cause a personal injury and/or
material damage.
• Do not put items filled with water on the
refrigerator.
CAUTION
WARNING
DA99-03957C-06.indb 3 2015. 5. 7. �� 3:51
04_ safety information
- If spilled, there is a risk of fire or electric shock.
• Do not let children hang on the door.
- Failure to do so may cause serious personal
injury.
• Do not leave the doors of the refrigerator open
while the refrigerator is unattended and do not
let children enter inside the refrigerator.
• Do not allow babies or children go inside the
drawer.
- It can cause death from suffocation by
entrapment or personal injury.
• Do not sit on the Freezer door.
- The door may be broken and cause a personal
injury.
• To prevent children entrapment, you must
reinstall the divider using provided screws after
cleaning or other actions if you removed the
divider from the drawer.
• Never put fingers or other objects into the
dispenser hole.
- Failure to do so may cause personal injury or
material damage.
• Do not store volatile or flammable substances
such as benzene, thinner, alcohol, ether or LP
gas in the refrigerator.
- The storage of any of such products may cause
an explosion.
• Do not store low temperature-sensitive
pharmaceutical products, scientific materials or
other low temperature-sensitive products in the
refrigerator.
- Products that require strict temperature controls
must not be stored in the refrigerator.
• Do not place or use electrical appliance inside
the refrigerator, unless they are of a type
recommended by the manufacturer.
• Do not use a hair dryer to dry the inside of the
refrigerator. Do not place a lighted candle in the
refrigerator for removing bad odors.
- This may result in an electric shock or fire.
• Do not touch the inside walls of the freezer or
products stored in the freezer with wet hands.
- This may cause frostbite.
• Do not use mechanical devices or any other
means to accelerate the defrosting process,
other than those recommended by the
manufacturer.
• Do not damage the refrigerant circuit.
• This product is intended only for
the storage of food in a domestic
environment.
• Bottles should be stored tightly together so that
they do not fall out.
• In the event of a gas leak (such as propane
gas, LP gas, etc.), ventilate immediately without
touching the power plug. Do not touch the
appliance or power cord.
- Do not use a ventilating fan.
- A spark may result in an explosion or fire.
• Use only the LED Lamps provided by
manufacturer or service agent.
• Children should be supervised to ensure that
they do not play with and/or climb into the
appliance.
• Do not disassemble or repair the
refrigerator by yourself.
- You run a risk of causing a fire, malfunction
and/ or personal injury. In case of malfunction,
please contact your service agent.
• If the appliance generates a strange
noise, a burning or smell or smoke,
unplug the power plug immediately and
contact your nearest service center.
- Failing to do so may result in an electric or fire
hazards.
• If you experience difficulty when changing the
light, contact service agent.
• If the products is equipped with the LED Lamp,
do not disassemble the Lamp Cover and LED
Lamp by yourself.
- Please contact your service agent.
• If any dust or water is in the refrigerator, pull
out power plug and contact your Samsung
Electronics service center.
- There is a risk of fire.
CAUTION SIGNS FOR USING
• To get best performance from the
product,
- Do not place foods too closely in front of the
vents at the rear of the appliance as it can
obstruct free air circulation in the refrigerator
compartment.
- Wrap the food up properly or place it in airtight
containers before putting it into the refrigerator.
- Do not put any newly introduced food for
freezing near to already existing food.
• Do not place carbonated or fizzy drinks in the
freezer compartment. Do not put bottles or
glass containers in the freezer.
- When the contents freeze, the glass may
CAUTION
DA99-03957C-06.indb 4 2015. 5. 7. �� 3:51
safety information _05
break and cause personal injury and property
damage.
• Do not change or modify the functionality of the
refrigerator.
- Changes or modifications may result in a
personal injury and/or property damage. Any
changes or modifications performed by a
3rd party on this completed appliance are
neither covered under Samsung warranty
service, nor is Samsung responsible for safety
issues and damages that result from 3rd party
modifications.
• Do not block air holes.
- If the air holes are blocked, especially with a
plastic bag, the refrigerator can be over cooled.
If this cooling period lasts too long, the water
filter may break and cause water leakage.
- Do not put any newly introduced food for
freezing near to already existing food.
• Please observe maximum storage times and
expiry dates of frozen goods.
• Fill the water tank, ice tray, water cubes only
with potable water.
• Use only the ice-maker provided with the
refrigerator.
• The water supply to this refrigerator must only
be installed/connected by a suitably qualified
person and connected to a potable water
supply only.
• In order to operate the ice-maker
properly, water pressure of 138~862kPa
(1.4~8.8kgf/cm³) is required.
• Do not spray volatile material such as
insecticide onto the surface of the appliance.
- As well as being harmful to humans, it may also
result in an electric shock, fire or problems with
the product.
• Do not apply strong shock or excessive force
onto the surface of glass.
- Broken glass may result in a personal injury
and/or property damage.
CAUTION SIGNS
FOR CLEANING AND
MAINTENANCE
• Do not directly spray water inside or
outside the refrigerator.
- There is a risk of fire or electric shock.
• Do not use or place any substances sensitive
to temperature such as inflammable sprays,
inflammable objects, dry ice, medicine, or
chemicals near the refrigerator. Do not keep
volatile or inflammable objects or substances
CAUTION
(benzene, thinner, propane gas, etc.) in the
refrigerator.
- This refrigerator is for storing food only.
- This may result in a fire or an explosion.
• Do not spray cleaning products directly on the
display.
- Printed letters on the display may come off.
• Remove any foreign matter or dust from the
power plug pins. But do not use a wet or damp
cloth when cleaning the plug, remove any
foreign material or dust from the power plug
pins.
- Otherwise there is a risk of fire or electric shock.
• Never put fingers or other objects into the
dispenser hole and ice chute.
- It may cause a personal injury or material
damage.
• Unplug the refrigerator before cleaning
and performing maintenance.
SEVERE WARNING SIGNS FOR
DISPOSAL
• Ensure that none of the pipes on the
back of the appliance are damaged prior
to disposal.
• R-600a or R-134a is used as a refrigerant.
Check the compressor label on the rear of
the appliance or the rating label inside the
refrigerator to see which refrigerant is used for
your refrigerator. When this product contains
flammable gas (Refrigerant R-600a), contact
your local authority in regard to safe disposal
of this product. Cyclopentane is used as an
insulation blowing gas. The gases in insulation
material require special disposal procedure.
Please contact your local authorities in regard
to the environmentally safe disposal of this
product. Ensure that none of the pipes on the
back of the appliances are damaged prior to
disposal. The pipes shall be broken in the open
space.
• When disposing of this product or other
refrigerators, remove the door/door seals, door
latch so that small children or animals cannot
become trapped inside. Leave the shelves in
place so that children may not easily climb
inside. Children should be supervised to ensure
that they do not play with the old appliance.
• Please dispose of the packaging material for
this product in an environmentally friendly
manner.
CAUTION
DA99-03957C-06.indb 5 2015. 5. 7. �� 3:51
06_ safety information
contents
SETTING UP YOUR REFRIGERATOR ……………………………………………… 07
OPERATING YOUR REFRIGERATOR ……………………………………………… 13
TROUBLESHOOTING ………………………………………………………………… 22
ADDITIONAL TIPS FOR
PROPER USAGE
• In the event of a power failure, call the local
office of your Electricity Company and ask how
long it is going to last.
- Most power failures that are corrected within
an hour or two will not affect your refrigerator
temperatures. However, you should minimize
the number of door openings while the power is
off.
- Should the power failure last more than 24
hours, remove all frozen food.
• If keys are provided with the refrigerator, the
keys should be kept out of the reach of children
and not be in the vicinity of the appliance.
• The appliance might not operate consistently
(possibility of temperature becoming too warm
in the refrigerator) when sited for an extended
period of time below the cold end of the range
of temperature for which the refrigerating
appliance is designed.
• Do not store food which spoils easily at low
temperature, such as bananas, melons.
• Your appliance is frost free, which means there
is no need to manually defrost your appliance,
as this will be carried out automatically.
• Temperature rise during defrosting can comply
with ISO requirements. But if you want to
prevent an undue rise in the temperature of
the frozen food while defrosting the appliance,
please wrap the frozen food up in several layers
of newspaper.
• Any increase in temperature of frozen food
during defrosting can shorten its storage life.
Saving Energy Tips
- Install the appliance in a cool, dry room with
adequate ventilation.
Ensure that it is not exposed to direct sunlight
and never put it near a direct source of heat
(radiator, for example).
- Never block any vents or grilles on the
appliance.
- Allow warm food to cool down before placing it
in the appliance.
- Put frozen food in the refrigerator to thaw. You
can then use the low temperatures of the frozen
products to cool food in the refrigerator.
- Do not keep the door of the appliance open for
too long when putting food in or taking food
out. The shorter time for which the door is
open, the less ice will form in the freezer.
- Clean the rear of the refrigerator regularly. Dust
increases energy consumption.
- Do not set temperature colder than necessary.
- Ensure sufficient air exhaust at the refrigerator
base and at the back wall of the refrigerator.
Do not cover air vent openings.
- Allow clearance to the right, left, back and top
when installing.
This will help reduce power consumption and
keep your energy bills lower.
- For the most efficient use of energy, please
keep the all inner fittings such as baskets,
drawers, shelves on the position supplied by
manufacturer.
This appliance is intended to be used in
household and similar applications such
as
- staff kitchen areas in shops, offices and other
working environments;
- farm houses and by clients in hotels, motels
and other residential type environments;
- bed and breakfast type environments;
- catering and similar non-retail applications.
DA99-03957C-06.indb 6 2015. 5. 7. �� 3:51
setting up _07
01 SETTING UP
GETTING READY TO INSTALL THE
REFRIGERATOR
Congratulations on your purchase of the Samsung
Refrigerator. We hope you enjoy the state-of-art
features and efficiencies that this new appliance
offers.
Selecting the best location for the
Refrigerator
• A location with easy access to the water supply.
• A location without direct exposure to sunlight.
• A location with level (or nearly level) flooring.
• A location with enough space for the
Refrigerator doors to open easily.
• Allow sufficient space to the right, left, back and
top for air circulation.
If the Refrigerator does not have enough space,
the internal cooling system may not work
properly.
• Please ensure that appliance can be moved
freely in the event of maintenance & service.
• Allow clearance to the right, left, back
and top when installing.
This will help reduce power consumption
and keep your energy bills lower.
• Do not install the Refrigerator where the
temperature will go below 50ºF (10ºC).
Setting up your Refrigerator
50mm
50mm
50mm
546mm 744mm
98mm
1388mm
908mm
335mm
125°
50mm
1578mm
125°
DA99-03957C-06.indb 7 2015. 5. 7. �� 3:51
08_ setting up
When moving your refrigerator
To prevent floor damage, be sure the front
adjusting legs are in the up position (above
the floor). Refer to ‘Adjusting the doors’ in
the manual (on page 10).
Flat-blade
screw driver(-)
Control Lever
FLOORING
For proper installation, you must place this
refrigerator on a level, hard surface that is the same
height as the rest of the floor.
This surface should be strong enough to support a
fully loaded refrigerator.
To protect the finish of the flooring, cut a large
section of the cardboard carton and place it under
the refrigerator where you are working.
When moving the refrigerator, you need to pull and
push it straight forwards or back.
Do not wiggle it from side to side.
CAUTION
REMOVING THE REFRIGERATOR
DOORS
For some installations you need to remove the
fridge and freezer drawers so you can move the
refrigerator to its final location.
Do not remove the doors/drawer if you don’t need
to. If you do not need to remove the refrigerator
doors, go to Adjusting the Level on page 8.
If you need to remove the doors. continue below.
Before removing the door/drawer, make sure you
read the following items:
Disconnect power to the refrigerator before
removing the door or drawer.
• Be careful not to drop, damage or
scratch the door/drawer while removing
them.
• Be careful not to get injured while removing the
door/drawer.
• Reattach the door/drawer properly to avoid:
- Moisture from air leakage.
- Uneven door alignment.
- Wasting energy due to improper door seal.
Disassemble the refrigerator doors
Be careful not to drop and scratch the
doors while removing the doors.
Required Tools (Not provided)
You need the following tools to complete the
installation of your refrigerator:
Philips
screwdriver (+)
Flat-blade screw
driver (-)
Socket wrench
(10mm)
Pliers
Allen wrench
(3/16”) (5mm)
WARNING
WARNING
DA99-03957C-06.indb 8 2015. 5. 7. �� 3:51
setting up _09
01 SETTING UP
Disassemble the refrigerator doors
1. With the door opened, remove the cap top
table ( 1 ) with a flat-blade screwdriver(-). and
close the door. Remove 2 screws holding down
the cover hinge ( 2 ) and turn it with several
wires connected.
2. Disconnect one connector ( 3 ) on the right side
door and one connector ( 4 ) on left side door.
To remove the water coupler from the hinge,
twist and pull it from the hinge. Remove the
water line ( 5 ) while pressing the marked part
( 6 ) of the water line coupler.
3. Pull and remove the hinge lever ( 7 ). Remove
the ground screw ( 8 ) attached to the upper left
and right door hinges with a philips screwdriver
(+). Remove the upper left and right door hinges
( 9 ).
4. Lift the door
straight up to
remove.
5. Remove the screw ( 10 ) attached to the
lower left and right door hinges with a philips
screwdriver(+). Remove the 2 hex head bolts
( 11 ) attached to the lower left and right door
hinges with an allen wrench (3/16”). Remove
the lower left and right door hinges ( 12 ).
REATTACHING THE
REFRIGERATOR DOORS
To reattach the fridge doors after you have moved
the fridge to its final location, assemble parts in
reverse order.
DISASSEMBLE THE FREEZER
DRAWER
1. Take out the upper
drawer by lifting it up.
2. Remove the tilting
pocket ( 1 ) by pulling
both support guards
( 2 ) upward at the
same time.
3. Take out the lower
basket ( 3 ) by lifting
the basket up from the
rail system.
4. Remove 4 hex head bolts
from both sides with a
socket wrench (10mm).
1
2
3
1
2
4
5
6
3
7
8
9
Allen wrench
12
10
11
DA99-03957C-06.indb 9 2015. 5. 7. �� 3:51
10_ setting up
5. Lift up the freezer door
from the rails.
ASSEMBLE THE FREEZER
DRAWER
To reattach the drawer after you have moved the
fridge to its final location, assemble parts in reverse
order.
ADJUSTING THE LEVEL
Make sure the refrigerator is level so that you can
make final adjustments. Use a level to test if the
refrigerator is level both side to side and back to
front. If the refrigerator is not level, it will not be
possible to get the doors perfectly even, which
may cause moisture condensation and increased
energy bills. Below is an example of how to level
the refrigerator if the left side of the refrigerator is
lower than the right side.
How to adjust the level
1. Open the freezer drawer and remove the lower
basket. (See to page 7)
2. Remove the two
screws ( 1 ) attached
to the cover leg front
( 2 ) with a Philips
screwdriver (+).
3. Remove the cover
leg front ( 2 ) by lifting
the bottom part of the
cover leg front up and
pulling it out.
4. Insert a flat-blade
screwdriver (-) into a
notch on the left control lever, and turn it count
clockwise to level the refrigerator. (You turn the
lever clockwise to lower the refrigerator and
counterclockwise to raise it.)
Both control levers must be touching the
floor to avoid possible personal injury or
property damage because of tipping.
If the right side is lower, perform the same
procedure, but with the right control lever.
It is difficult to remove the cover leg
front from the refrigerator, so we do not
recommend making small adjustments
with the control lever. Instead, refer to the
next page for the best way to make minor
adjustments to the doors.
MAKING MINOR ADJUSTMENTS
BETWEEN DOORS
Remember, a leveled refrigerator is necessary
for getting the doors perfectly even. If you need
help, review the previous section on leveling the
refrigerator.
The left door is fixed. To make minor
adjustments between doors, adjust only the
right door.
1. Pull out the freezer drawer ( 1 ), then you can
see the lower hinge ( 2 ).
2. Insert a philips screwdriver (+) ( 3 ) into the shaft
( 4 ) of the lower hinge.
3. Adjust the height by turning a philips screwdriver (+)
( 3 ) clockwise (
DOWN
) or counterclockwise (
UP
).
When you turn a philips screwdriver (+)
counterclockwise ( ), the door will move up.
CAUTION
Slot
Slot
2
1
flat-blade screwdriver(-)
Control Lever
Adjustment
part
Fixed part
(3)
(1)
(3)
(2)
(4)
DA99-03957C-06.indb 10 2015. 5. 7. �� 3:51
setting up _11
01 SETTING UP
ADJUSTING THE FREEZER
DRAWER LEVEL
1. Locate the height-adjuster (1) in the freezer
drawer.
Unscrew the four Phillips screws (2) slightly to
loosen the door.
2. Loosen the controller screw ( 3 ) with a Phillips
screwdriver (+).
3. Find the best level to align the door slope.
• After adjustment,
tighten the
controller screw
and then the philips
screws.
INSTALLING THE WATER
DISPENSER LINE
A water dispenser with a filter is one of the helpful
features on your new refrigerator. To help promote
better health, the water filter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need
to purchase a water purifying system to do that.
In order for the ice maker to operate properly, a
water pressure of 20~125 psi is required.
Under normal conditions, a 170 cc (5.75 oz.) cup
can be filled in about 10 seconds.
If the refrigerator is installed in an area with low
water pressure (below 20psi), you can install a
booster pump to compensate for the low pressure.
After you have connected the water line, make
sure the water storage tank inside the refrigerator is
properly filled. To do this, press the water dispenser
lever until the water runs from the water outlet.
Water line installation kits are include with
unit. You can find it in freezer drawer.
The new hose-sets supplied with the
appliance are to be used and that old hose-
sets should not be reused.
Parts for water line Installation
Water line fixer and screws Pipe connector
Water line
Freezer Drawer
Adjustment part
1
2
3
Example) The slope is about 0.08inch (2mm) as shown below.
- Rotate the height adjuster to -2.0 to reduce the door slope.
Slope
Reference
plane
DA99-03957C-06.indb 11 2015. 5. 7. �� 3:51
12_ setting up
Connecting to the water supply line
1. First, shut off the main water supply line.
2. Locate the nearest cold, drinking water line.
3. Follow the Water line Installation Instructions in
the installation kit.
4. After connecting the water supply to the water
filter, turn your main water supply back on and
dispense about 3L to clear and prime the water
filter.
Connecting the water line to the
refrigerator
1. Remove the cap from water line on the unit and
insert compression nut to the water line on the
unit after disassembling from provided water
line.
2. Connect both water line from the unit and water
line in the kit.
3. Tighten the compression nut onto the
compression fitting. There should be no gaps
between (A, B & C )
4. Turn water on and check for any leakage.
Only connect the water line to a drinkable
water source. If you have to repair or
disassemble the water line, cut off 6.5mm
of the plastic tubing to make sure you get a
snug, leak-free connection.
Before being used, the leakage in these
places should be examined.
• Samsung Warranty
does not cover
WATER LINE
INSTALLATION.
• It will be done at
customer’s charge
unless the retail price includes installation cost.
• Please contact Plumber or Authorized Installer
for the installation if needed.
• If Water leakage occurs due to improper
installation, Please contact installer.
COMPLETING THE SET UP
Now that you have your new refrigerator installed
in place, you are ready to set up and enjoy the
features and functions of the appliance. By
completing the following steps, your refrigerator
should be fully operational.
1. Make sure your refrigerator is in an appropriate
location with reasonable clearance between it
and the wall. Refer to installation instructions in
this manual.
2. Once the refrigerator is plugged in, make sure
the interior light comes on when you open the
doors.
3. Set the Temperature control to the coldest
temperature and wait for an hour. The freezer
will get slightly chilled and the motor will run
smoothly. Reset the refrigerator and freezer to
the temperatures you want.
4. After you plug the refrigerator in, it will take a
few hours to reach the appropriate temperature.
You can store food and drinks in the refrigerator
after the temperature is sufficiently cool.
CAUTION
CAUTION
The water line must be connected to
the cold water pipe. If it is connected
to the hot water pipe, it may cause the
purifier to malfunction.
Close Main
Water pipe
Close Main
Water pipe
No gap
Remove
cap
Water Line
from unit
Water Line
from Kit
No gap
Loosen a
DA99-03957C-06.indb 12 2015. 5. 7. �� 3:51
operating _13
02 OPERATING
USING THE CONTROL PANEL
( 1 ) Energy
Saver
Touching this button turns Energy Saver
mode on and off. When you turn Energy
Saver on, the Energy Saver icon lights.
Turn Energy Saver off and the icon
goes off. The Energy Saver function
automatically turns on. when power is
supplied to the refrigerator.
If condensation or water drops appear
on the doors, turn the Energy Saver
mode off.
( 2 ) Freezer
(Hold 3 sec
for Power
Freeze)
Touch this button to set the freezer to
your desired temperature.
You can set the temperature between
-8°F and 8°F (between -22°C and
-14°C). Touch and hold this button for 3
seconds to decrease the time needed
to freeze products in the Freezer. It can
be helpful if you need to quickly freeze
easily spoiled items or if the temperature
in the freezer has warmed dramatically
(For example, if the door was left open).
( 3 ) Alarm
/ hold 3sec
for Filter
Reset
This button serves two purposes:
1) To turn the door open alarm on and
off
If the door alarm is set to On, an alarm
beeps if any refrigerator door is left
open for more than three minutes. The
beeping stops when you close the door.
The door alarm function is pre-set to
On in the factory. You can turn it off by
touching and then releasing this button.
You can turn it back on in the same
fashion. The icon lights up when the
function is on.
2) To reset the water filter life indicator.
After you replace the water filter, touch
and hold this button for 3 seconds to
reset the water filter life indicator.
( 4 )
Lighting/
Hold 3 sec
for C↔F
Touching this button turns on the
Dispenser LED lamp (under the display)
in continuous mode so that it stays on
continuously. The button also lights
up. If you want the Dispenser lamp to
come on only when some one uses the
dispenser, touch this button to turn the
continuous mode off. Touch and hold
this button for 3 seconds to switch the
temperature units between °C and °F.
( 5 ) Fridge
(Hold 3sec
for Power
Cool)
Touch this button to set the fridge to
your desired temperature. You can set
the temperature between 34°F and 46°F
(between 7°C and 1°C). Touch and hold
this button for 3 seconds to decrease
the time needed to cool products in
the Refrigerator. It can be helpful if you
need to quickly cool easily spoiled items
or if the temperature in the fridge has
warmed dramatically (For example, if the
door was left open).
( 6 ) Ice Off
(Hold 3 sec
for child
lock)
If you don’t want to make more ice,
touch this button. Also, pressing this
button for 3 seconds turns on Child
Lock which locks the display panel
and dispenser buttons so the buttons
can not be used. The Child Lock icon
lights up to indicate you’ve activated the
Child Lock function. Press 3 seconds
to unlock.
( 7 ) Ice
Type
Touch this button to select your desired
ice type. Cubed and crushed ice modes
alternate when you press the button.
This mode can not be used with the
Water mode simultaneously.
(Cubed) (Crushed)
( 8 ) Water Touch this button to dispense water.
This mode can not be used with the
Ice Type mode simultaneously. Water
mode will be off if you touch the Ice Type
button.
Water
Operating your Refrigerator
8 910 7
1
2
3
5
6
4
DA99-03957C-06.indb 13 2015. 5. 7. �� 3:51
14_ operating
( 9 ) Ice Off If you don’t want to make more ice,
touch the Ice Off button.
The icon will light up and the Ice-Maker
stops making ice.
We recommend you stop ice
making if the following occur:
- There is enough ice in the ice
bucket.
- You want to save water and
energy.
- Water is not being supplied to
the refrigerator.
If the ice maker function is
ON, and the water Line is not
connected, there will be a water
valve noise from the back of the
unit, press the Ice Off (Hold 3sec
for child lock) button for less
than 3 seconds until the Ice Off
Indicator ( ) illuminates.
If you do not press any button(letters not ICON),
the display turns off in a few seconds.
If you press any button(letters not ICON), the
display lights up again.
The function key will operate after you remove
your finger from the letters except E.Saver, Ice
and Water key.
( 10 ) Filter Water filter usage
This icon will light up when you need to
change the filter. After you use about
300 gallons of water, the filter indicator
lights up. (about 6 months).
The icon will blink red for several
seconds when you open or close the
door.
After you install the new water filter, reset
the filter indicator by touching the Alarm/
hold 3 sec for Filter Reset button.
• If water is not dispensing or
dispensing slowly, you need to
replace the water filter because
the water filter is clogged.
• Some areas have large amounts
of lime in their water, which
causes the water filter to clog
more quickly.
CHANGING THE WATER FILTER
To reduce risk of water damage to your
property DO NOT use generic brands of
water filters in your SAMSUNG Refrigerator.
USE ONLY SAMSUNG BRAND WATER FILTER.
SAMSUNG will not be legally responsible for any
damage, including, but not limited to property
damage caused by water leakage from use of a
generic water filter. SAMSUNG Refrigerators are
designed to work ONLY WITH SAMSUNG Water
Filter. If you want to purchase any accessories,
please contact with Samsung service center.
The Filter light turns red to let you
know when it is time to change your
water filter cartridge.
To give you time to get a new filter,
the red light comes on just before the
capacity of the current filter runs out.
Changing the filter on time provides you with the
freshest, cleanest water from your refrigerator.
1. Shut off the water supply. Then, turn the water
filter ( 1 ) about 1/4 turn, counter-clockwise.
2. Pull the water filter ( 1 ) from the case filter ( 2 ).
• To change the water filter more easily,
shut off the water supply valve.
• Sometimes, it is hard to disassemble the water
filter because impurities in the water cause it to
stick. If you are having difficulties, grip the water
filter firmly and pull it hard.
• When you pull the
water filter, a little
water can leak from
the opening. This is
normal. To minimize
the water leaks, keep
the filter cartridge horizontal when you pull it.
• To prevent overflow, empty the water filter tray
( 3 ) and dry around the filter case ( 2 ).
3. Insert the new filter into the filter case ( 4 ).
4. Push the filter, and then turn it clockwise until it
locks.
• If you have trouble inserting the water
filter because of high water pressure,
shut off the water supply valve.
• The locked symbol should be lined up with the
indicator line.
WARNING
(Red)
2
1
3
2
DA99-03957C-06.indb 14 2015. 5. 7. �� 3:51
operating _15
02 OPERATING
1. Touch the “Alarm/
hold 3 sec for
Filter Reset” button
(
(Filter Reset)
) for about 3
seconds to reset the water
filter. The color of indicator ( ) changes from
red to light off.
2. If you turned off the water supply, turn it back
on.
For a replacement water filter, you can visit
your local home Improvement center or
contact the Samsung Parts distributor. Be
sure the replacement water filter has the
SAMSUNG logo on the box and on the
water filter. Link : http://www.samsungparts.
com
Removing any residual matter inside the
water supply line after installing the water
filter.
1. Turn ON the main water supply and supply
water from water supply line.
2. Run water through the dispenser until the water
runs clear (approx. 6 to 7 minutes). This will
clean the water supply system and remove air
from the lines.
3. Additional flushing may
be required in some
households.
4. Open the Refrigerator
door and make sure
there are no water leaks
coming from the water
filter.
Be sure to flush the dispenser thoroughly,
otherwise water may drip from the
dispenser.
This means that there is still air in the line.
Reverse Osmosis Water Supply
IMPORTANT:
The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet
valve of the refrigerator needs to be between 35
and 120 psi (241 and 827 kPa).
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to
be a minimum of 40 to 60 psi (276 to 414 kPa.) If
the water pressure to the reverse osmosis system
is less than 40 to 60 psi (276 to 414 kPa):
• Check to see whether the sediment filter in the
reverse osmosis system is blocked. Replace
the filter if necessary.
• Allow the storage tank on the reverse osmosis
system to refill after heavy usage.
• If your refrigerator has a water filter, it may
further reduce the water pressure when used
in conjunction with a reverse osmosis system.
Remove the water filter.
If you have questions about your water pressure,
call a licensed, qualified plumber.
CONTROLLING THE
TEMPERATURE
Basic temperature of Freezer and
Refrigerator Compartments
The basic temperature and recommended
temperatures of the Freezer and Refrigerator
Compartments are -2°F and 38°F (or -19°C and
3°C)respectively. If the temperature of the Freezer
and Refrigerator Compartments are too high or
low, adjust the temperature manually.
Controlling the Freezer temperature
The Freezer temperature can be set between -8°F
and 8°F (or between -22°C and -14°C) to suit
your particular needs. Press the Freezer button
repeatedly until the desired temperature is shown
in the temperature display. The temperature will
change by 2°F (or 1°C) with each press. See
below.
Fahrenheit : -2°F
➞
-4°F
➞
-6°F
➞
-8°F
➞
8°F
➞
6°F
➞
4°F
➞
2°F
➞
0°F
➞
-2°F.
Centigrade : -19°C
➞
-20°C
➞
-21°C
➞
-22°C
4
Recommend Temp (Freezer) : -2°F (or -19°C )
DA99-03957C-06.indb 15 2015. 5. 7. �� 3:51
16_ operating
➞
-14°C
➞
-15°C
➞
-16°C
➞
-17°C
➞
-18°C
➞
-19°C.
Keep in mind that foods like ice cream may melt at
4°F (or 0°C). The temperature display will move
sequentially from -8°F to 8°F (or from -22°C to
-14°C).
Controlling the fridge temperature
The fridge temperature can be set between
between 34°F and 46°F (or between 7°C and
1°C) to suit your particular needs. Press the Fridge
button repeatedly until the desired temperature is
shown in the temperature display. The temperature
will change by 2°F (or 1°C) with each press. See
below.
Fahrenheit : 38°F
➞
36°F
➞
34°F
➞
46°F
➞
44°F
➞
42°F
➞
40°F
➞
38°F.
Centigrade : 3°C
➞
2°C
➞
1°C
➞
7°C
➞
6°C
➞
5°C
➞
4°C
➞
3°C.
The temperature control process for the Fridge
works just like the Freezer process. Press the
Fridge button to set your desired temperature.
After a few seconds, the Fridge will begin adjusting
towards the newly set temperature. This will be
reflected in the digital display.
- The temperature of the Freezer, Fridge or
Flex Zone may rise when you open the
doors too frequently, or if a large amount
of warm or hot food is placed inside.
- This may cause the digital display to blink. Once
the Freezer and Fridge temperature return to
their normal set temperatures, the blinking will
stop.
- If the blinking continues, you may need to “reset”
the Refrigerator. Try unplugging the appliance,
wait for around 10 minutes and then plug the
power cord back in.
- If there is a communication error between the
Display and Main Controller, the Convertible
Display light may blink. If the blinking continues
for a long period of time, please contact a
Samsung Electronics Service Center.
USING THE COLD WATER
DISPENSER
Push the appropriate ice type button
to select what you want dispensed.
Using the ice Dispenser
Place a glass underneath the ice
dispenser and push gently against the
dispenser lever with your glass.
Make sure the glass is in line with
the dispenser to prevent the ice from
bouncing out.
Please wait 2 seconds before
removing the glass under the
dispenser to prevent spills.
If the Refrigerator door opens, the
Dispenser does not work.
When Cubed Ice is selected after using
the Crushed Ice mode, a small amount of
residual crushed ice might be produced.
Do not pull the lever out. You could damage
or break the lever’s spring.
• To clean the ice bin/bucket, wash with a mild
detergent, rinse well, and dry thoroughly it. Do
not use harsh or abrasive cleaners or solvents.
• When you select Cubed Ice after using the
Crushed Ice mode, a small amount of residual
crushed ice might be produced.
CAUTION
CAUTION
CAUTION
Recommend Temp (Fridge) : 38°F (or 3°C )
NO ICE
Select this if you want to
turn ice maker off
check the
water level
Test button
DA99-03957C-06.indb 16 2015. 5. 7. �� 3:51
operating _17
02 OPERATING
• If ice doesn’t come out, pull out the ice bucket
and press the test button located on the right
side of ice maker.
• Do not press the test button continuously when
the tray is filled with ice or water. Water may
overflow or ice may jam the bucket.
• Normal Use
To fill the ice bucket to maximum capacity after
installation, follow these steps:
Water may overflow or ice may jam the bucket.
1. Allow your refrigerator to operate and cool
down for 24 hours (or 1 full day).
- Waiting 24 hours will allow your ice maker to
cool properly.
2. Dispense 4 to 6 ice cubes into the glass.
3. After 8, and then 16 hours, dispense a full glass
of ice.
• When you press the Test button, you will hear
the refrigerator chime (ding-dong). When the
chime sounds, release the Test button.
• The chime sounds automatically again to let
you know the ice maker is working well.
If a power failure occurs, ice cubes may
melt then freeze together when the power
comes back on, causing the dispenser to
be out of order.
To prevent this problem, after a power failure, pull
out the ice bucket and discard the residual ice or
water.
After you dump the ice from the ice bucket,
you should press the dispenser lever once
with the ‘ICE CUBED’ or ‘CRUSHED’
function ON.
The ice maker will make new ice faster after you
return the ice bucket to the freezer.
If you use all the ice at once, you must
repeat Steps 2 and 3 on the previous page.
However, only wait 8 hours before dispensing the
first 4 to 6 ice cubes. This will replenish the ice
cubes and ensure maximum ice production.
CAUTION
CAUTION
Using the ice off Function
When you select the Ice Off mode, remove all ice
cubes from the bucket. If you are not using the ice
dispenser, the ice cubes may clump together. Pull
the lock lever forward to remove the bucket. Throw
away the ice cubes or clumped ice. Push the
bucket back until you hear a click.
Use only the ice maker provided with
the refrigerator. The water supply to
this refrigerator must only be installed/
connected by a suitably qualified person.
Connect to a potable water supply only.
To operate the ice maker properly, water pressure
of 138 ~ 862kPa is required.
If you have a long vacation or business trip and
won’t use the water or ice dispensers for a long
time:
- Close the water valve. Otherwise, water leakage
may occur.
- Remove all food.
- Unplug the refrigerator.
- Wipe excess moisture from inside and leave
the doors open. Otherwise, odor and mold may
develop. Do not put your fingers, hands or any
other unsuitable objects in the chute or ice-
maker bucket.
- It may result in personal injury or material
damage. Never put your finger or any other
objects in the dispenser opening.
- It may cause injury.
Do not try to disassemble the ice maker.
Do not wash or spray the ice bucket with water
while it is in the refrigerator. Remove it to clean
it.
When you insert the Ice maker tray, be
sure that the tray is well centered at the
entrance.
Otherwise, the tray may be stuck.
CAUTION
CAUTION
PULL PUSH
DA99-03957C-06.indb 17 2015. 5. 7. �� 3:51
18_ operating
Water clouding phenomenon
All water provided to the refrigerator flows
through the core filter which is an alkaline
water filter. In the filtering process, the
pressure of the water that has flowed out
of the filter is increased, and the water
becomes saturated with oxygen and
nitrogen. When this water flows out into
the air, the pressure plummets and the
oxygen and nitrogen get supersaturated,
which results in gas bubbles. The water
may temporarily look misty or cloudy due to
these oxygen bubbles. After a few seconds,
the water will look clear.
Please wait 1 second before removing
the cup after dispensing water to prevent
spills. Do not pull out the lever dispenser
after dispensing ice or water. It comes back
automatically. Ice is made in cubes. When
you select “Crushed”, the ice maker grinds
the ice cubes into crushed ice.
PARTS AND FEATURES
Use this page to become more familiar with the
parts and features of the refrigerator.
USING THE COOL SELECT
PANTRY PLUS (ON SOME
MODELS)
The Cool Select Pantry PLUS is a full-width drawer
with an adjustable temperature control. This pantry
can be used for large party trays, deli items,
pizzas, beverages or miscellaneous items. There
is a temperature sensor which adjusts the amount
of cold air allowed into the pantry. The Pantry’s
control buttons are located on the right side of the
pantry.
• The Pantry has three modes: The Fresh mode,
Chilled mode, and Deli mode. Fresh mode is
the default. Press the Temp button repeatedly
until the mode you want is lit. Once you select
a mode, the temperature will change to match
the mode you selected.
• The Pantry temperature may change depending
on the number of items inside and where they
are located, the ambient temperature, and how
often the door is opened.
The Pantry Selection Button
1. When you select “Deli”, the temperature of the
pantry will be kept around 41°F (or 5°C). This
feature helps keep food fresh for a long time.
2. When you select
“Fresh”, the
temperature of the
pantry will be kept
around 38°F (or 3°C).
This feature helps keep
food fresh for a longer
time.
3. When you select
“Chilled”, the
temperature of the
pantry will be kept
around 34°F (or 1°C). This feature also helps
keep meat or fish fresh for a longer time. The
table below lists the Pantry modes and the
kinds of foods that can be stored safely for
each mode.
DA99-03957C-06.indb 18 2015. 5. 7. �� 3:51
operating _19
02 OPERATING
Deli Fresh Chilled
• Pineapple • cucumbers • steaks
• lemon • apples • hard cheeses
• avocado • oranges • cold cuts
• potato • grapes • bacon
• zucchinis • hot dogs
• corn
Fruits and vegetables may be damaged
when the “chilled” mode is set.
Do not store lettuce or other leafy produce in this
pantry.
Do not store glass bottles in this pantry. If
they are frozen, they can break and cause
personal injury.
REMOVING THE REFRIGERATOR
ACCESSORIES
1. Door Bins & Dairy Compartment
• Door Bins (1)
To remove - Simply lift the bin up and pull straight
out.
To relocate - Slide it in above the desires location
and push down until it stops.
• Door Bins (2)
To remove - Take the right side of the bin out by
lifting it obliquely along the guide and then, take the
left side out by pulling it from the door.
To relocate - Slide it into the original location and
push down until it sticks.
Injury may occur if the door bins are not
firmly assembled.
Do not allow children to play with bins. Sharp
corners of the bins may cause injury.
CAUTION
1
2
Do not adjust a bin full of food. Remove the
food first.
Dust removal method - Remove the guard and
wash in water.
2. Tempered Glass shelves
To remove - Tilt up the front of the shelf in the
direction shown ( 1 ) and lift it up vertically ( 2 ). Pull
the shelf out.
To relocate - Tilt the front of the shelf up and
guide the shelf hooks into the slots at a desired
height. Then lower the front of the shelf so that the
hooks can drop into the slots.
The Tempered Glass shelves are heavy.
Use special care when removing them.
3. Vegetable & Fruit Drawers
To remove - Pull the drawer out to full extension.
Tilt up the front of the drawer and pull straight out.
To relocate - Insert the drawer into the frame rails
and push back into place.
The drawers need to be removed before
the glass shelf above them can be lifted
out.
4. Cool Select PantryPLUS
To remove the Flex
Zone – Pull the pantry
out to full extension.
Tilt up the front side
of the pantry and pull
straight out.
To relocate the Flex Zone – Push the rails to the
back of the refrigerator. Place the drawer onto the
rails and slide the pantry back until it is in place.
CAUTION
CAUTION
CAUTION
1
2
DA99-03957C-06.indb 19 2015. 5. 7. �� 3:51
20_ operating
To remove the divider – Pull the pantry
completely out to full extension and raise the front
side of the divider to unhook it from the rear wall of
the pantry, then lift the divider out.
To relocate the divider - Hook the back of the
divider over the rear wall of the pantry and push
the divider down.
Using the doors
Ensure that the doors close all the way and are
securely sealed.
When the refrigerator door is only partially open, it
will automatically close. But, the door will stay open
when opened more than the auto close range and
you must close it manually.
Using the tilting pocket
You can use the Tilting Pocket to store frozen pizza
and similar items up to 16” in diameter.
REMOVING THE REFRIGERATOR
ACCESSORIES
1. Tilting Pocket
To remove - Pull both brackets ( 1 ) upward until
you hear a clicking sound and remove the pocket.
To relocate - Hook the ends of the pocket into
both brackets ( 2 ) and push down until it locks into
place.
2. ICE BUCKET
To remove - Lift the ice bucket ( 1 ).
To relocate - Place the ice bucket into the Super
extended drawer ( 2 ).
3. Super Extended Drawer
To remove - Pull the drawer out to full extension.
Tilt up the rear of the drawer and lift straight out.
To relocate - Place the drawer onto the rails ( 4 )
by tilting it up. Lower the drawer into place until it is
horizontal and slide the Drawer ( 3 ) in.
4. Freezer Drawer
To remove the freezer drawer - Pull the freezer drawer
out fully. Tilt up the rear of the bin and lift it out to remove.
To relocate the freezer drawer - Place the bin
into the rail assembly.
You can scratch the side of the bin if you twist it left
or right when disassembling or re-assembling it.
Do not allow babies or children go inside the
freezer drawer. They could damage the refrigerator
and seriously injure themselves. Do not sit on the
freezer door. The door may break. Do not allow
children to climb into the freezer drawer.
Do not remove the divider.
If trapped inside, children may be injured or
suffocate to death.
CAUTION
CAUTION
CAUTION
WARNING
1
2
3
4
1
DA99-03957C-06.indb 20 2015. 5. 7. �� 3:51
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/