Hitachi RAC-10SH2 Руководство пользователя

OUTDOOR UNIT

INDOOR UNIT

– 1 –

Instruction manual

Page 1~48

To obtain the best performance and ensure years of trouble free use, please read this instruction manual completely.

SPLIT TYPE AIR CONDITIONER

INDOOR UNIT/OUTDOOR UNIT

MODEL

ENGLISH

DEUTSCHFRANÇAISITALIANOSPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

«®¬¬¥£¤

RAS-1 SH3

RAS-18SH3/RAC-18SH3

8

RAC-1 SH

8

Для достижения наивысшей производительности и обеспечения длительной безаварийной

внимательно изучите данную инструкцию .

Инструкция по эксплуатации

стр.

49 ~9 6

работы

3

• Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

• Pay special attention to signs of “

Warning” and “ Caution”. The “Warning” section contains matters which, if

not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may result

in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

• The signs indicate the following meanings. (The following are examples of signs.)

• Please keep this manual after reading.

PRECAUTIONS DURING OPERATION

WARNING

SAFETY PRECAUTION

• Do not reconstruct the unit.

Water leakage, fault, short circuit or fi re may occur if you reconstruct the unit by

yourself.

• Please ask your sales agent or qualified technician for the installation of your unit.

Water leakage, short circuit or fire may occur if you install the unit by yourself.

• Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the

earth line of telephone. Improper installation of earth line may cause electric

shock or fire.

• Be sure to use the specifi ed piping set for R410A. Otherwise, this may result in

broken copper pipes or faults.

• A circuit breaker should be installed depending on the mounting site of the unit.

Without a circuit breaker, the danger of electric shock exists.

• Do not install the unit near a location where there is fl ammable gas. The outdoor

unit may catch fi re if fl ammable gas leaks around it. Piping shall be suitable

supported with a maximum spacing of 1m between the supports.

• Please ensure smooth fl ow of water when installing the drain hose.

• Make sure that a single phase 220V power source is used.

The use of other power sources may cause electrical components to overheat

and lead to fi re.

PRECAUTIONS DURING INSTALLATION

PROHIBITION

CONNECT EARTH LINE

PROHIBITION

WARNING

CAUTION

•

• Should abnormal situation arise (like burning smell), please stop operating the

unit and remove plug from the socket. Contact your agent. Fault, short circuit or

fi re may occur if you continue to operate the unit under abnormal situation.

• Please contact your agent for maintenance. Improper self maintenance may cause electric

shock and fi re.

• Please contact your agent if you need to remove and reinstall the unit. Electric shock or fi re

may occur if you remove and reinstall the unit yourself improperly.

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

• Do not use any conductor as fuse wire, this could cause fatal accident.

• During thunder storm, disconnect the plug top and turn off the circuit

breaker.

• Do not put objects like thin rods into the panel of blower and suction side

because the high-speed fan inside may cause danger.

• Spray cans and other combustibles should not be located within a meter of the

air outlets of both indoor and outdoor units.

As a spray can’s internal pressure can be increased by hot air, a rupture may result.

PROHIBITION

“OFF”

This sign in the fi gure indicates prohibition. Indicates the instructions that must be followed.

PROHIBITION

– 2 –

Avoid an extended period of direct airflow for your health.

• Do not place plants directly under the airfl ow as it is bad for the plants.

• Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus such

as the electric kettle, oven etc.

• The product shall be operated under the manufacturer specifi cation and not

for any other intended use.

PRECAUTIONS DURING OPERATION

CAUTION

• Do not attempt to operate the unit with wet hands, this could cause fatal

accident.

• When operating the unit with burning equipments, regularly ventilate

the room to avoid oxygen insuffi ciency.

• Please ensure that outdoor mounting frame is always stable, fi rm and without

defect. If not, the outdoor unit may collapse and cause danger.

• Do not wash the unit with water or place a water container such as a vase on

the indoor unit.

Electrical leakage could be present and cause electric shock.

• Be sure to stop the operation by using the remote controller and turn off the

circuit breaker during cleaning, the high-speed fan inside the unit may cause

danger.

• Turn off the circuit breaker if the unit is not be operated for a long period.

• Do not climb on the outdoor unit or put objects on it.

• When operating the unit with the door and windows opened, (the room

humidity is always above 80%) and with the air defl ector facing down or moving

automatically for a long period of time, water will condense on the air deflector

and drips down occasionally. This will wet your furniture. Therefore, do not

operate under such condition for a long time.

• If the amount of heat in the room is above the cooling or heating capability of

the unit (for example: more people entering the room, using heating equipments

and etc.), the preset room temperature cannot be achieved.

• Indoor unit cleaning must be performed by authorized personnel only. Consult

This appliance is not intended for use by young children or infirm persons unless they have been

Young children should be supervised to ensure that they do not play with the appliance.

your sales agent.

adequately supervised by a responsible person to ensure that they can use this appliance safely.

Using a commercially available detergent or similar can damage the plastic parts

or clog the drain pipe, causing water to drip with potential electric shock hazard.

• Do not touch the air outlet, bottom surface and aluminium fi n of the outdoor

unit.

You may get hurt.

Do not touch the refrigerant pipe and connecting valve.

Burns may result.

PROHIBITION

DON’T WET

PROHIBITION

DON’T TOUCH

“OFF”

PROHIBITION

DON’T TOUCH

STRICTLY OBSERVE

PRECAUTIONS

“OFF”

DEUTSCHFRANÇAISITALIANOSPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

РУССКИЙ

– 3 –

ENGLISH

•

Drain Port (bottom)

Air Outlet

Discharges cool air when in heating

mode and warm air when in cooling

and dry cool modes, and warm or

cold air when in the dehumidifying

mode.

NAMES AND FUNCTIONS OF EACH PART

INDOOR UNIT

OUTDOOR UNIT

Signal Receiver

(internal)

Receive signal from the

remote control.

Indicator

Front Panel

(Page 8)

Horizontal/

Vertical Air Deflector

(internal)

Air Outlet

Remote Controller

Pipe/Wiring

Drain Hose

Drains dehumidified water generated from the indoor unit when in

the cooling, dehumidifying and dry cool modes.

Air Inlet (rear and left side)

噝 Even if the operation is stopped, the outdoor

unit fan continues to rotate for 10~60 seconds

to cool down the electrical parts.

噝 In heating operation, condensed water and

defrosted water is discharged from the outdoor

unit. Do not block the drain port as the water in

the drain may freeze in a cold area.

噝 Even during cooling operation, the water

condensed in the pipe, etc. may flow out from

the outdoor unit.

噝 When installing the outdoor unit under eaves,

etc. of the apartment, install a bush and drain

pipe on the drain port for drainage treatment.

ABOUT OUTDOOR UNIT

(Understanding The Operating Mechanism, page 39)

Earth Terminal

(side bottom)

噝 While the power is on, a very small amount of power is

consumed within the control circuit even when the unit

is not in operation.

Power can be saved if the circuit breaker is switched off.

CAUTION

Pull out the power plug if the unit is not in

use for a long period.

(Or turn off the circuit breaker.)

Infrared

Dynamic Air Deflection Sensor

Temporary Operation Switch

(Forced Cooling Switch)

When the remote

controller does not

work due to factors

like dead batteries,

you can press the

temporary operation

switch to start

temporary

operation. (Page 44)

– 4 –

Ion Mist Unit

Operation temperature of outdoor is -15ą to 43ą

Air Cleaning Mesh Box

DEUTSCHFRANÇAISITALIANOSPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

РУССКИЙ













Replace the air cleaning mesh box.

ǅ“Make sure that it clicks into place.”

ǅ“If it dose not click into place, abnormal sounds

may be heard or the box may fall off.”

Close the front panel.

Ą







INDOOR UNIT CONTROL PANEL / CLEANING UNIT

Open the front panel to operate. (How to open the front panel, page 8)

Dust Catcher

Collects the dust swept by

the cleaning unit. (At front

and top.) (Page 37)

Dust Box

Collects and keeps the dust

that has been cleaned.

(Page 34)

Stainless Mesh Filter

(inside)

Collects particulates and dusts in the air. (Page 35)

Air Cleaning Mesh Box

Preparation

Stop the air conditioner, and disconnect

the power supply (or turn off the circuit breaker).

Open the front panel.

Pull out the air cleaning mesh box as illustrated to

remove it.

Insert the air cleaning mesh into the slot as illustrated.

Connect the power cord (or turn on the circuit breaker).

Jaw

With the air cleaning mesh used, the air-conditioning capability will fall slightly.

Remove dust from the surface with a vacuum cleaner, and DO NOT clean it with water.

(We recommend you clean it once every 6 months and replace it once every 2 years.)

– 5 –

ENGLISH

Cleaning Unit

Cleans the dust

caught by the

stainless mesh

filter.

Wasabi-Nano Titanium Air Cleaning Mesh

How to Attach the Wasabi-Nano Titanium Air Cleaning Mesh

Transmission Indicator

The transmission indicator

ROOM TEMPERATURE

Button

Press this button to set the

room temperature. Keep

pressing and the value will

change more quickly.

STOP Button

HEAT Button

Press this button to start

heating operation.

(Page 14)

DEHUMIDIFY Button

Press this button to start

dehumidifying operation.

(Page 14)

COOL Button

Press this button to start

cooling operation.

(Page 15)

DRY COOL Button

Press this button to start dry

cool operation. (Page 16)

AUTO Button

Press this button to

start automatic operation.

(Page 13)

BUTTONS TO

START OPERATIONS

Remote controller can be used when it is fixed on a wall or pillar using the remote controller holder.

Before fixing it, make sure the indoor unit can be controlled from the remote controller fixing point.

SLEEP TIMER Operation Button

Press this button to start sleep timer

operation. (Page 29)

REMOTE CONTROLLER

Transmits the operation and timer settings to the indoor unit.

The LCD shown in the illustration below is the display immediately after the reset switch is pressed. Usually not

all the data are displayed. On the LCD shown below, the functions not available for this room air conditioner are

also displayed.

NAMES AND FUNCTIONS OF EACH PART (continued)

Transmission Part

HUMIDITY Button

Press this button to set the

humidity for dehumidify and

dry cool operations.

Screw

INFRARED HUMAN-PRESENCE

SENSING Button

Press this button to enter

the dynamic air deflection mode.

(Page 19, 20)

Press this button to start I on mist

operation.

– 6 –

Press this button to stop any

operation except the preset timer.

lit when a signal is sent.

ION MIST Button

(Page

18)

These are preset functions

except for

(SAVE).

Preset can be done if these

buttons are pressed while the

air conditioner is stopped,

however, the unit will not

function accordingly.

FUNCTION SELECTOR

Buttons

Each time when you press,

blinking changes in the

following sequence (page 12,

21, 22, 23):

ON/OFF Button

Use this button to set or cancel

the function selected by the

function selector.

FUNCTION SELECTOR

(When the door is open)

MANUAL CLEAN Button

Starts filter cleaning operation

while the air conditioner

operation is stopped. (Page 32)

FAN SPEED Button

VERTICAL AIRFLOW Button

Use this button to swing the

vertical air deflector or to adjust

the angle to your preference.

(Page 24)

HORIZONTAL AIRFLOW

Button

Use this button to swing the

horizontal air deflector or

to adjust the angle to your

preference. (Page 25)

SET TIME Button

Use this button to set and

check the current time.

(Page 11)

TIMER Buttons

RESET Button

Press this button after the

batteries are replaced and

when the air conditioner does

not function properly. (Page 11)

DEUTSCHFRANÇAISITALIANOSPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

РУССКИЙ

POWERFULL Button

Press this button to start

powerful operation. (Page 18)

MANUAL/AUTO Button

Press this button to switch

between auto/manual

dehumidifying and dry

cool operation. (Page 17)

DYNAMIC AIR DEFLECTION

Button

Press this button to start

dynamic air operation.

(Page 20)

– 7 –

ENGLISH

Press this button to

select fan speed.

Four options are available:

Auto, H i, M ed,L ow,and Silent.

















•

2



•

Take out the anti-mold wasabi

cassette from the aluminium bag.

Do not remove or tear

the aluminium sheet on

the surface nor make a

hole on it.

•

Remove the dust box housing

Dust Box Housing

Handle

INSTALLING ANTI-MOLD WASABI CASSETTE

Open the front panel.

•

Do not hold the movable panel

when opening and closing the

front panel.

Front panel

Gripping part

Panel support

•

Hold and lift up the front panel.

•

Push up the panel support until it

clicks to lock it.

Lower the front panel and fix in

position with the panel support.

Install the anti-mold wasabi cassette.

Aluminium bag

Slide the anti-mold

wasabi cassette that

has been taken out of

the wrapper directly

into the Dust Box

Housing.

CAUTION

• Do not put your face close to the package when

you open it.

Your eyes or nose may be irritated by wasabi aroma.

• Do NOT eat.

1

No daily maintenance is required. However,

the effectiveness of anti-mold wasabi cassette

will be lost after approximately 10 years have

elapsed. Replace the anti-mold wasabi cassette

in such event.

CAUTION

•

Do not open the front panel during operation

.

It may interrupt the movable panel to work properly.

Be sure to stop

the operation first before opening

the front panel.

Anti-mold wasabi

cassette

– 8 –

DEUTSCH



DEUTSCHFRANÇAISITALIANOSPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

РУССКИЙ

Close the front panel.

•

Hold and lift up the front panel.

CAUTION

• If the front panel is loose, it may come off and drop.

• When opening the front panel upwards, please do not use excessive force.

If the front panel comes off the device, this may cause it to malfunction.

• When the front panel remains open, be sure to push up the panel

support.

•

Push down the panel support until it clicks.

Push the both ends of the front panel first and

then its center until it clicks.

•

Pull it downward.

3

– 9 –

ENGLISH

FILTER CLEANING UNIT OPERATION CHECK

Make sure the power plug is firmly plugged into the power outlet.

WARNING

• Be sure to use the power outlet exclusively for

air conditioner

Use of other power outlet may cause heat, which

could result in fire.

• Make sure that dust is not deposited on the

power plug and be sure to plug in until the blades

of the plug are fully inserted to avoid unstable

plug-in

and dust from being accumulated

Use of air conditioner with dusty power plug or

improper power connection could result in electrical

shock or fire.

CAUTION

Do not operate with

wet hands

It may cause electric

shock.

Compulsory

Wet Hand

Prohibited

Performing operation check after the power is turned on.

Perform the filter cleaning unit operation check

• After the power is turned on (after the power plug is inserted into the power

outlet or after the circuit breaker is switched on after power failure), the

cleaning unit makes one cycle of back and forth movement.

• At this time, the

(CLEAN) indicator is lit.

• One cycle of operation check will take approximately 5 minutes.

• During the operation check, the unit performs “Fan” operation while the movable

panel and horizontal air deflector remain closed.

• If the

(CLEAN) indicator blinks (lit for 4 seconds/off 1 second) after the

operation check, refer to “Troubleshooting” on page 44.

Cleaning Unit

There is a filter cleaning wiper inside.

Dust catcher

CAUTION

Do not put your fingers or a stick etc into the top surface during

the filter cleaning operation

It may result in injury or malfunction.

• The illustration shows the unit without front

panel for your reference only.

1

2

Compulsory

7(0325$5<

6:,7&+

– 10 –

DEUTSCHFRANÇAISITALIANOSPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

РУССКИЙ

DEUTSCH

Address

PREPARE THE REMOTE CONTROLLER

Install the batteries.

• Use two AAA-size batteries.

Set the current time (Ex: set to 1:30 p.m.)

RESET

1

2

Press the (TIMER) button to adjust to the current time.

• You can fast forward the time by continuously pressing the

button.

Confirm the current time

• Press the

(SET TIME) button to check the current time

(The time display disappears 3 minutes later). If necessary,

readjust the time following the above procedure 1 and 2.

• Address selector switch is used to prevent

remote controller signal interference in such

circumstance where 2 indoor units are used in

the same room. This switch is not usually used.

(The factory setting is at “A” side.)

For this setting, please make an inquiry to your

sales agent.

Address selector

switch

Switch lever

Remote controller

backside

Do not operate by yourself.

Push mark

and pull.

ABOUT ADDRESS SELECTOR SWITCH

Time is incremented

Time is decremented

Press

(SET TIME) button to set the current time.

• “AM” or “PM” is lit instead of

blinking. It automatically goes

off in 10 seconds.

1

2

Open the cover and press the RESET

button with a sharp tip item.

3

• 18:88 lights up on the current

time display and “AM” and

“PM” start blinking.

CAUTION

1. Do not mix new and old batteries, or

different type of batteries together.

2. Remove the batteries when you do

not use the remote controller for 2 or 3

months.

DEUTSCH

– 11 –

ENGLISH

1

While (SAVE) is blinking, point the remote controller towards

the unit and press the (ON/OFF) button.

• A short beep sounds and

(SAVE) indicator turns on.

Press the (FUNCTION SELECTOR)

button until

(SAVE) blinks.

Press the (FUNCTION SELECTOR) button again until

(SAVE) blinks.

While

(SAVE) is blinking, point the remote controller towards

the unit and press the (ON/OFF) button.

• A short beep sounds and

(SAVE) indicator turns off, indicates

the setting is released.

Notes for “save” setting

• If ampere is set to “Save”, the maximum heating capacity slightly lowers

and starting up of heating operation will take a little longer. Besides,

the preset temperature may not be reached if outside temperature is

low.

• Point the remote controller to the signal receiver of the unit

Signal reception distance is approximately 7m in front of the unit.

However, this distance may be shorter or the signal may not be

receivable if there is an electronic lighting device in the same room.

• Handle the remote controller with care

Dropping it or getting it wet may compromise its signal transmission

capability. After new batteries are inserted into the remote controller,

the unit require approximately 10 seconds before it can respond to

commands and begin operation.

WHEN OPERATING THE REMOTE CONTROLLER

Approximately

7m from the front

PREPARE THE REMOTE CONTROLLER (continued)

Ampere setting (Standard/Save) can be selected.

If you experience frequent circuit breaker tripping, set ampere to “Save” to avoid this problem.

(Ampere is set to “Standard” at the time of purchase.)

4

2

RELEASE

– 12 –

SPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

РУССКИЙ

AUTOMATIC OPERATION

•

ǌ

1

2

1

7(0325$5<

6:,7&+

Based on the room temperature and outside temperature, the unit determines the most suitable operation

mode (heating, dehumidifying or cooling) and a comfortable temperature. (Set the current time on the remote

controller before starting operation.)

Press the (AUTOMATIC OPERATION) button

to set the operation mode to auto.

•

Every time you press it, the mode will change as

shown in the chart on the right.

Press the (STOP) button.

Press the (STOP) button again.

A short beep sounds and the automatic

operation stops.

Operation mode will be displayed on the

remote controller display.

Increase

Decrease

Adjust the room temperature

Press the (ROOM TEMPERATURE)

button.

• Every time you press it, a short beep sounds and the

temperature will change by 1°C.

•

is displayed if the temperature is set higher than

the automatically set room temperature by 1°C.

is displayed if the temperature is set lower than the

automatically set room temperature by 1°C.

• The adjustable temperature range is not higher or lower

than 3°C of the automatically set room temperature.

• Humidity setting cannot be adjusted.

Select the fan speed

Press the (FAN SPEED) button.

• “AUTO”, “LOW” and “SILENT”

can be selected.

• Every time you press it, the

mode will change as shown in

the chart on the right.

Beep

STOP

• Performs heating operation when the room temperature is below 23°C.

Set the temperature to be around 23°C.

• Performs dehumidifying operation when the room temperature is 23~26°C.

The preset temperature will be the room temperature at the time of start of air conditioner

operation.

• Performs cooling operation when the room temperature is above 27°C.

Set the temperature to be around 27°C.

Room temperature and fan speed can be adjusted to your preference.

AUTOMATIC OPERATION

Heating

Dehumidifying

Cooling

Even if dehumidifying operation is set, the air conditioner may not execute dehumidifying if the room humidity

is not very high. This is not a malfunction.

DEUTSCHFRANÇAISITALIANOSPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

РУССКИЙ

– 13 –

ENGLISH

•

HEATING OPERATION

Press the (HEAT) button to start heating operation.

Press the (HEAT) button.

• Adjust the room temperature and fan speed to your preference.

Temperature range between 16°C~32°C can be set.

Press the (STOP) button.

A short beep sounds and heating operation stops.

STOP

DEHUMIDIFYING OPERATION

3 types of dehumidifying operations can be performed by pressing the (DEHUMIDIFY) button.

Performs powerful dry operation without lower down the room temperature.

Press the (DEHUMIDIFY) button.

• Every time you press the (DEHUMIDIFY) button,

the mode will change as shown in the chart below.

Condensation

Control

Auto

Dehumidifying

Quick

Laundry

(“AUTO” flashes for 5 seconds)

•

In auto dehumidifying mode, fine adjustment of room temperature, humidity

adjustment and fan speed selection can be made to your preference.

Every time you press the ROOM TEMPERATURE button, the temperature will change

by 1°C. (Temperature setting range is not higher or lower than 3°C.) Every time

you press the HUMIDITY button, the humidity will change by 5%. (Humidity setting

range is 40%~70%.)

• In quick laundry mode, fine adjustment of room temperature and fan speed

Press the (STOP) button.

• A short beep sounds and dehumidifying operation stops.

STOP

• After the dehumidifying operation is stopped, the remote controller will display the

operation mode that had been set before the (DEHUMIDIFY) button was

pressed.

ENGLISH

DEUTSCHFRANÇAISITALIANOSPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

РУССКИЙ

– 14 –

selection can be made to your preference. (Fine adjustment of room

temperature and humidity adjustment cannot be made in condensation

control mode.)

DEHUMIDIFYING OPERATION (continued)

Auto

Dehumidifying

Operation modeIn this situation

Operating mechanism

• In damp

weather

• In most of the cases, the room temperature at the time the button is

pressed becomes the preset temperature.

(

When room temperature is below 12°C, set 13°C. When it is

13°C~22°C, set +2°C. When it is below 23°C~26°C, set room

temperature. When it is above 26°C, set 26°C)

•

Target humidity is around 50~60%. If the humidity becomes lower than

the target value, operation stops. If it becomes higher than the target

value, operation resume.

• The operation mode may automatically be switched to cooling or

heating for temperature control. (Refer to table below)

• To dry the

laundry

quickly

• Detects outdoor temperature, room temperature and humidity to

automatically select the most suitable combination of heating and

powerful dehumidifying operations.

• This operation is performed together with stainless plasma air purifying

operation.

• Priority is given to laundry drying.

Be sure use this mode when no one is in the room as the room

temperature and humidity will be high temporarily.

• 3-hour timer function is used for this operation mode.

• When

controlling

condensation

formed on

windows in

winter time

• To control the condensation, priority is given to the operation for

lowering humidity.

Therefore, the room temperature goes down in

this operation mode. The operation stops if the room temperature

becomes 1°C or below.

• 2-hour timer function is used for this operation mode.

Condensation

Control

Quick Laundry

• Be careful when condensation control operation is performed if the outside temperature is low as it will lower the

room temperature.

• (OFF TIMER) and (ON TIMER) (page 26), which are to be set using clock function, are not available during

dehumidifying (quick laundry and condensation control modes) operation. However, the timer (for 30 minutes

and 1-9 hours) can be set for quick laundry and condensation control modes with the (SLEEP) button.

• To set to your desired temperature and humidity while executing dehumidifying, it is recommended to use manual

dehumidifying function. (Page 17)

• If you do not wish room temperature to be too high when drying the laundry, use the preference (Powerful) mode

instead of quick laundry mode. (Page 18)

The operation mode may automatically be switched to cooling or heating for temperature control.

At this time, the room humidity may vary by approximately 10%.

Heating

operation

Dehumidifying operation

Operation

stop

Cooling

operation

About 3

°C

Approx. 3°C if outside temp. is

below approx. 32°C.

Approx. 1°C if outside temp. is

above approx. 32°C.

Room temperature set

Current room temperature

1ºC

COOLING OPERATION

Press the (COOL) button to start cooling operation.

Press the

(COOL) button.

• Adjust the room temperature and fan speed to your preference.

Temperature range between 16°C~32°C can be set.

Press the

(STOP) button.

• A short beep sounds and cooling operation stops.

STOP

– 15 –

ENGLISH

•



If you want to set the desired temperature and humidity during dry cool operation, we recommend

you use the manual cooling operation. (Page 17)

STOP

DRY COOL OPERATION

When you operates cooling operation with the dry function, press the (DRY COOL) button, the air conditioner

automatically sets temperature and humidity in dry cool mode.

Press the (DRY COOL) button.

•

Adjust the room temperature and fan speed to your preference.

• Every time you press the (ROOM TEMPERATURE) button, the

temperature will change by 1°C.

(Temperature setting range from the auto set temperature is not higher or

lower than 3°C.)

Press the (STOP) button.

• A short beep sounds and dry cool operation stops.

Humidity

to be set

Temperature

to be set

Based on the detected outside and room temperature,

the temperature is set on an hourly basis within the range

of 24~28°C.

• Even if the room temperature

reached the preset temperature,

the air conditioner may continue

to operate if the preset humidity

has not been reached.

50% when temperature above 27°C is set.

55% when temperature of 26°C is set.

60% when temperature below 25°C is set.

Dry

intermittent

operation

Dry cool operation

Operation

stops

Cooling

operation

About 3ºC

Approx. 3°C if outside temp. is

below approx. 32°C.

Approx. 1°C if outside temp. is

above approx. 32°C.

Room temperature set Current room temperature

About 1ºC

The operation mode may automatically be switched to cooling or heating for temperature control.

If the room temperature is lower than the preset temperature, intermittent operation (repeat of operation state

and stop state) is performed to avoid excessive lowering of temperature and to control the humidity.

DEUTSCHFRANÇAISITALIANOSPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

РУССКИЙ

– 16 –

ĄThe default setting is AUTO.

ǅAdjustment Range of Dehumidifying Operation

Room Temperature

Humidity

Automatically adjusted in the

range of

50% to 60%

Auto-controlled

temperature

±3°C

Auto-controlled

temperature

±3°C

Auto dry cool

operation

Manual dry cool

operation

ǅAdjustment Range of Dry Cool Operation

Setting Range of AUTO/MANUAL Operation

•

Press the AUTO/MANUAL button.

Example: Dehumidifying

Indicates

MANUAL

40 70

SWITCHING BETWEEN AUTO/MANUAL DEHUMIDIFYING/DRY COOL OPERATION

The AUTO/MANUAL button allows you to set the temperature and humidity manually during

dehumidifying/

dry cool operation.

operation

10°C~32°C

16°C~32°C

– 17 –

ENGLISH

Switches to the manual mode if the machine is working in the auto

dehu

midifying/dry cool operation.

Switches to the auto mode if the machine is working in the manual

dehu

midifying/dry cool operation.

Auto dehumidifying

Manual dehumidifying

噝Ion mist operation is the combined operation mode of the fan operation

and moisturizing operation.

噝If the Ion mist mode is set while the air conditiconer is in basic operation mode, the air purifying function by

the electric dust collector will operate together.

Press the (ION MIST) button.

噝Adjust the fan speed to your preference. “HI”, “MED”, “LOW”, “SILENT”

can be selected.

噝When only Ion mist operation is set,

and (ON TIMER) preset cannot be done.

(OFF TIMER)

Press the (STOP) button.

噝A short beep sounds and Ion mist

operation

stops.

STOP

Press the (ION MIST) button.

CANCEL

during

operation

POWERFUL OPERATION

噝

噝The airflow will be extended so that the air can reach even further during powerful operation.

(Extended Airflow)

Press the (POWERFUL PERATION) button during operation.

噝A short beep sounds and the preference (Powerful) operation starts.

( POWERFUL) indicator lit on the remote controller.)

CANCEL

Press the (POWERFUL PERATION) button again.

噝 POWERFUL) indicator turns off on the remote controller.

Operation modeIn this situation

Operating mechanism

Heating

噝 When you want the room to be

a little warmer

噝 Set approximately 2°C higher than the preset

temperature. Powerful heating operation is

performed.

Cooling

噝 When you want a little cooler

air

噝 When you want the room to be

a little cooler

Auto Dehumidifying

噝 When you want to remove

humidity a little faster

噝 Laundry drying efficiency is enhanced.

噝 Condensation-control efficiency is enhanced.

Dehumidifying

噝 Set approximately 3°C lower than the preset

temperature. Powerful cooling operation is

performed.

噝 High speed dehumidifying operation is performed

aiming to achieve humidity of approximately 40%.

Condensation

Control

Quick Laundry

By pressing the (POWERFUL PERATION) button during auto, heating, dehumidifying, cooling or stainless

plasma air purifying operation, the air conditioner performs the “Powerful” operation.

ION MIST OPERATION

– 18 –

, the electric dust collector operation

,,,

Example: Cooling

With the infrared sensor, the air conditioner can detect the activity level in a room and adjust the temperature

and humidity automatically, thus achieving the purpose of energy saving.

Press the INFRARED SENSOR button.

The infrared sensor automatically adjusts the

indoor temperature and humidity according to

the activity level in the room. However, the

temperature

and humidity specified by the

remote controller remain unchanged.

1

•

The energy saving effect can be achieved only after the energy-saving temperature control function keeps

working

for more than 2 hours.

In the energy-saving temperature-control mode, the energy consumption saved by the air conditioner varies with

the activity level.

•

INFRARED HUMAN PRESENCE SENSING FUNCTION

•

Sensor in operation

Operation mode

Reduces the preset temperature

in one of the following cases:

Operation Description

Heating

Cooling

Auto

Dehumidifying/Dry Cool

Operation mode Actions in case of no person

eDecreases the temperature by 2°C.

eIncreases the temperature by 2°C .

eIncreases the temperature by 5–10%.

eEnergy-saving operation in auto mode.

•

Auto

Cooling

Heating

•

Raises the preset temperature

in one of the following cases:

Low activity level

Low indoor temperature

•

Increases the preset temperature

in one of the following cases:

Energy-saving operation in auto

mode.

The infrared sensor detects changes to the infrared generated by human bodies. Therefore, the accuracy

of infrared

sensor may be affected negatively in the following cases:

e

e

The activity level is very low (reading, watching TV, etc.) or human bodies are blocked by a screen, cabinet, or glass board.

e

e

The indoor temperature is very high and exceeds or approaches the human body temperature (when the refrigeration

just begins).

e

e

The person wears thick clothes and turns his/her back to the air conditioner.

e

e

Curtains or plant leaves swing due to pet movement or airflow.

Low activity level

Low indoor temperature

•

The tracing function (Page 20) can further reduce the energy consumption.

After detecting that the person leaves the room for 30 minutes, the air conditioner turns to the energy-saving modes

according to the settings in the remote controller as shown in the right table, but the preset temperature and humidity

in the remote controller remain unchanged.

When the air conditioner works in powerful operation, setting the energy-saving mode will cancel the powerful operation.

High activity level

High indoor temperature

– 19 –

ENGLISH

DYNAMIC AIR DEFLECTION FUNCTION (TRACING/EVASION)

The infrared sensor can detect the position of people and automatically change the airflow direction.

Press the AUTO AIR DEFLECTION button to switch the air deflection

mode.

ƽHow to change the detection speed of the sensor of the dynamic air deflection (tracing/evasion) function:

e

There are 2 detection speeds: “Standard” (by intervals of 15"–3') and “Slow” (by intervals of 1'–10').

e

The remote controller is set to the standard speed by default.

e

When the detection speed of the sensor is too high, set the detection speed to “Slow”

(when people and pets in the room behave frequently, resulting in frequent changes to the airflow direction).

e

After the dynamic air deflection mode is set, the sensor usually works once every 15 seconds to 3 minutes to

detect the position of the person and adjusts the airflow direction accordingly.

(The airflow direction does not change with the movement of human body immediately.)

e

If the dynamic air deflection mode fails to achieve the desired effect, adjust the airflow direction manually.

e

When the machine works in cooling, dehumidifying, or dry cool operation after the dynamic air deflection is set,

if the indoor humidity/temperature is very high, the left/right/upper/lower air deflectors may change their angles

to prevent drop of condensed water. After the temperature falls, the air conditioner returns to the dynamic air

deflection status.

1

e(Tracing) Adjusts the airflow direction

automatically to send the air flow to

the location of the person.

e

(Tracing) Adjusts the airflow direction

automatically to keep the air flow away

from the location of the person.

e

Return to the setting prior to the dynamic

air deflection mode.

Pressing the

DYNAMIC

AIR DEFLECTION

button

Release the

Dynamic Air

Deflection button

Operation Description

Example: Heating









Hold down after the running stops

Select the desire setting.

(Finely tuned within +3 to -3. The indicator turns off 10 seconds later)

Press the (STOP) button eThe settings are saved.

Set the detection speed of the sensor to “Slow”.

After the running stops, hold down for more than 5 seconds while pressing and holding .

e

At this time, the air conditioner beeps for signal receiving.

e

Return to the “Standard” mode by repeating the above procedure (until the air conditioner beeps for

signal receiving).

In addition to “Standard” and “Slow” modes, you can also fine tune the detection speed of the sensor.

Fine tune the detection speed of the sensor

DEUTSCHFRANÇAISITALIANOSPANISHPORTUGUÊS

∂ÏÏËÓÈÎ¿

РУССКИЙ

– 20 –

Страница загружается ...

Hitachi RAC-10SH2 Руководство пользователя

Это руководство также подходит для

Hitachi RAC-10SH2 Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов