Yamaha DVX-S100 Руководство пользователя

DVD HOME THEATER SOUND SYSTEM

DVX-S100

DVX-S100: DVR-S100 + NX-S100S + NX-S100C + SW-S100

OWNER’S MANUAL

U

CAUTION

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within

an equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle

is intended to alert you to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

IMPORTANT SAFETY INSTRUCTIONS

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

product and cart combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into

the product,

c) If the product has been exposed to rain or water,

CAUTION

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in

performance - this indicates a need for service.

20 Replacement Parts – When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or other

hazards.

21 Safety Check – Upon completion of any service or repairs

to this product, ask the service technician to perform safety

checks to determine that the product is in proper operating

condition.

22 Wall or Ceiling Mounting – The unit should be mounted to

a wall or ceiling only as recommended by the manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

70, provides information with regard to proper grounding of

the mast and supporting structure, grounding of the lead-in

wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection

to grounding electrodes, and requirements for the

grounding electrode.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one

of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

FCC INFORMATION (for US customers only)

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies

that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as

practical.

CAUTION

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place with at least 10 cm on the top, 10 cm on the left and

right, and 10 cm at the back of DVR-S100, and 20 cm on the

top, 10 cm on the left and right, and 10 cm at the back of

SW-S100 — away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds. To

prevent fire or electrical shock, do not place this unit where

it may get exposed to dripping or splashing, and never put

any objects filled with liquids, such as vases, on the top of

the unit.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in a environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit in a place where foreign objects

and liquid might fall. It might cause a fire, damage to this

unit and/or personal injury. Do not place the following

objects on this unit:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may cause

electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall outlet,

grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and

may cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

13 To prevent damage by lightning, disconnect the power cord

from the wall outlet during an electrical storm.

14 Take care of this unit so that no foreign objects and/or liquid

drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed.

The cabinet should never be opened for any reasons.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

16 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

17 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

18 Before moving this unit, press STANDBY/ON to set this

unit in the standby mode, and disconnect the AC power plug

from the wall outlet.

19 VOLTAGE SELECTOR (General model only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC main supply.

Voltages are 220/240 V AC, 50 Hz.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off. This state is called the standby mode. In

this state, this unit is designed to consume a very small

quantity of power.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the bottom of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide

slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-

003.

DANGER

Visible laser radiation when open. Avoid direct exposure to

beam.

When this unit is plugged to the wall outlet, do not place your

eyes close to the opening of the disc tray and other openings to

look into inside.

The laser component in this product is capable of emitting

radiation exceeding the limit for Class 1.

The name plate is located on the bottom of the unit.

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound

come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

We Want You Listening For A Lifetime

1

English

CONTENTS

INTRODUCTION

FEATURES .......................................................................... 2

CHECKING THE ACCESSORIES ................................... 3

INSTALLING BATTERIES IN THE REMOTE

CONTROL ........................................................................... 3

CONTROLS AND FUNCTIONS ....................................... 4

Front panel ......................................................................... 4

Remote control (AMP mode) ............................................ 6

Front panel display (left) ................................................... 8

Front panel display (right) ................................................. 9

PREPARATION

PREPARATION STEPS ................................................... 10

SPEAKER SETUP ............................................................. 11

Speaker placement ........................................................... 11

Installing the speakers ..................................................... 12

CONNECTIONS ................................................................ 14

Connecting TV and audio/video components ................. 14

Connecting the antennas .................................................. 16

Connecting the speakers .................................................. 17

Connecting to an external amplifier ................................ 19

Connecting the AC power cord ........................................ 19

Turning on the power ....................................................... 19

ADJUSTING SPEAKER OUTPUT LEVELS ................ 20

Using the test tone ........................................................... 20

USING BASIC FUNCTIONS

BASIC PLAYBACK .......................................................... 21

Basic operations ............................................................... 21

Selecting a sound field program ...................................... 23

RECORDING .................................................................... 28

PLAYING A DISC

DISC INFORMATION ..................................................... 29

Types of disc that this unit can play ................................ 29

Region management information .................................... 29

Notes about handling discs .............................................. 29

MP3 playback .................................................................. 30

REMOTE CONTROL (DVD MODE) ............................. 31

PLAYING A DISC ............................................................. 32

Basic operation ................................................................ 32

ON-SCREEN MENU ......................................................... 34

Operating menu bar ......................................................... 34

Icons for disc menu ......................................................... 35

Icons for player menu ...................................................... 36

USING MULTIPLE FUNCTIONS .................................. 38

Using a disc’s menu ......................................................... 38

Enhancing video quality

[U.S.A. and Canada models only] ................................... 38

DVD-Audio features ........................................................ 39

Enhancing audio quality (DISC DIRECT) ...................... 40

Switching audio tracks, subtitles and angles ................... 41

All group play .................................................................. 42

Programmed play ............................................................. 42

Random play .................................................................... 43

Bookmarks ....................................................................... 44

Repeat play ...................................................................... 45

Repeat A-B ...................................................................... 46

SETUP MENU ................................................................... 47

Operating the setup menu ................................................ 47

Summary of settings ........................................................ 48

Ratings ............................................................................. 51

PCM down conversion ..................................................... 51

Speaker settings ............................................................... 52

TUNING

TUNING ............................................................................. 54

Automatic and manual tuning ......................................... 54

Presetting stations ............................................................ 55

Tuning in to a preset station ............................................. 56

Exchanging preset stations .............................................. 56

REMOTE CONTROL FEATURES

OPERATING OTHER COMPONENTS USING THE

REMOTE CONTROL ....................................................... 57

Setting the manufacturer code ......................................... 57

ADJUSTMENTS

SET MENU ......................................................................... 59

List of SET MENU items ................................................ 59

Adjusting the items on the SET MENU .......................... 59

1 SPEAKER SET (speaker mode settings) .................... 60

2 LFE LEVEL ................................................................ 61

3 SP DLY TIME (speaker delay time) ........................... 62

4 D. RANGE (dynamic range) ....................................... 62

5 L/R BALANCE (balance of the front left and right

speakers) ...................................................................... 62

6 HP TONE CTRL (headphone tone control) ................ 62

7 I/O ASSIGN (input assignment) ................................. 63

8 INPUT MODE (initial input mode) ............................ 63

9 SP/PRE OUT (output source settings) ......................... 63

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS ........................................................................ 64

CHANGING THE PARAMETER SETTINGS FOR DSP

PROGRAMS ...................................................................... 65

Adjusting the delay time .................................................. 65

Adjusting the parameter settings for PRO LOGIC II

Music ............................................................................... 66

APPENDIX

TROUBLESHOOTING .................................................... 67

GLOSSARY ....................................................................... 72

SPECIFICATIONS ............................................................ 75

2

FEATURES

The DVX-S100 is the Home Theater Sound System that delivers a powerful and realistic sound experience like that

found in a movie theater just by combining the unit with the TV.

The newest DSP programs will enhance the power and realism of various sources, from movies to concerts, and

sporting events. Also, the Silent Cinema program allows you to enjoy the sound field even through the headphones.

Since the DVX-S100 consists of a DVD Audio/Video receiver, a center speaker, front speakers, rear speakers and a

subwoofer, you can enjoy stronger bass and surround effects as well as a good balance throughout the speakers.

Moreover, the One-touch connection of the speaker connectors designed exclusively for this unit allows you to easily

connect the speakers.

◆ Built-in 5-channel power amplifier

◆ DVD-AUDIO/VIDEO, CD, VCD, MP3, CD-R/

RW playback

◆ Dolby Pro Logic/Dolby Pro Logic II decoder

◆ Dolby Digital/Dolby Digital + Matrix 6.1

decoder

◆ DTS/DTS + Matrix 6.1 decoder

◆ Sophisticated FM/AM tuner

◆ CINEMA DSP: Combination of YAMAHA DSP

technology and Dolby Pro Logic, Dolby Digital

or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

◆ Easy connection of the center speaker, front

speakers and rear speakers using special speaker

connectors designed exclusively for this unit

◆ Multi-function remote control which can also be

used for other audio/video components of certain

manufacturers

■ About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using the buttons

on either the main unit or the remote control. In this

case, the operations performed by using the remote

control are described in this manual.

• This manual is printed prior to production. Design and

specifications are subject to change in part for the

reason of the improvement in operativity ability, and

others. In this case, the product has priority.

• Some of the illustrations and names of the package

contents etc written in this manual may differ from the

actual products and the names written on the package

etc.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are

trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Surround” are registered

trademarks of Digital Theater Systems, Inc.

(U.S.A. and Canada models)

“DCDi” is a trademark of Faroudja, a division of Sage

Inc.

This product incorporates copyright protection

technology that is protected by method claims of certain

U.S. patents and other intellectual property rights owned

by Macrovision Corporation and other rights owners. Use

of this copyright protection technology must be

authorized by Macrovision Corporation, and is intended

for home and other limited viewing uses only unless

otherwise authorized by Macrovision Corporation.

Reverse engineering or disassembly is prohibited.

3

INTRODUCTION

English

CHECKING THE ACCESSORIES

Check your package to make sure it contains the following items.

DVR-S100

Remote control

TV

CH

INPUT

TUNER

MUTE CD–R

VCR

VIDEO 2

VIDEO 1

MD

AV

SLEEP

POWER

TV MODE

POWER

VOL

REC

AUDIO

SUBTITLE

SHIFT

CODE SET

1

HALL

2

JAZZ

SETUP

3

ROCK

ANGLE

4

ENTERTAINMENT

MARKER

5

SPORTS

6

MONO MOVIE

PLAY MODE

7

MOVIE 1

REPEAT

8

MOVIE 2

A–B

DVD

CD

AMP

9

/DTS

TOP MENU

LEVEL

MENU

SET MENU

TEST

ON SCREEN

B. BOOST

RETURN

0

SELECT

>

–

10

MATRIX 6.1

GROUP

CANCEL

STEREO

PAGE

MUTE

VOL

ABCDE

ENTER

PRESET

CH

PRESET

CH

Batteries (x2)

(AA, R06, UM-3)

AM loop antenna

Indoor FM antenna

(U.S.A., Canada and

General models)

(Europe, U.K. and

Australia models)

NX-SW100 (NX-S100S x4, NX-S100C, SW-S100)

Fasteners (4 sets)

for the center

speaker

Pads

(2 sets: 16 pieces)

Speaker cables

(for the rear speakers: 15m (x2),

for the front/center speaker:

5m (x3))

System connector

cable (5m x 1)

INSTALLING BATTERIES IN THE REMOTE CONTROL

Insert the batteries in the correct direction by aligning the

+ and – marks on the batteries with the polarity markings

(+ and –) inside the battery compartment.

1 Press the part and slide off the battery

compartment cover.

2 Insert the two batteries (AA, R06, UM-3 type)

with + and – oriented properly.

3 Slide the cover back on so that it snaps into

place.

1

3

2

■ Notes on batteries

• Change all of the batteries if you notice a decrease in

the operating range of the remote control.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean the

battery compartment thoroughly before installing new

batteries.

Preserving the manufacturer code

Replace batteries early before they become unusable.

The manufacturer code set by the user will be

preserved for about two minutes when batteries run

out or when they are removed. Note that the

manufacturer code setting may be lost if more than

two minutes elapses. Also, if you press any button on

the remote control accidentally while replacing

batteries, the manufacturer code will be lost.

Non-skid pads

(2 sets: 16 pieces)

Video pin cable

103_S100_01-09_EN 02.5.13, 1:26 PM3

4

CONTROLS AND FUNCTIONS

Front panel

STANDBY/ON

A/B/C/D/E

PRESET/BAND PRESET/TUNING MEMORY

PROGRESSIVE

AUTO/MAN’L

DISC DIRECT

SILENT

12 3456890qwer

y

t

7

u

MEMORY

1 STANDBY/ON

Turns this unit on, or set it to the standby mode. When

you turn this unit on, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit will consume a small amount of

power in order to receive infrared-signals from the

remote control.

2 Disc tray

The disc you play is loaded on this tray.

3 v

Press to open and close the disc tray.

4 w

Press to start playback.

5 a (A/B/C/D/E)

(DVD mode)

Press to stop playback.

(Tuner mode)

Selects preset station groups A to E.

6 d (PRESET/BAND)

(DVD mode)

Press to pause.

(Tuner mode)

Switches the reception band between FM and AM and

also the mode between the tuning mode and the preset

mode.

7 t/e, r/y (d PRESET/TUNING /

PRESET/TUNING u)

(DVD mode)

Each time these buttons are pressed, the disc begins

playing from the beginning of the track you select. When

you keep pressing the buttons, the disc searches forward

or backward.

(Tuner mode)

Selects preset station numbers 1 to 8 when the colon (:)

appears in the front panel display.

Selects the tuning frequency when the colon (:) does not

appear.

8 PROGRESSIVE (MEMORY) (U.S.A. and

Canada models)

(DVD mode)

Switches between progressive video output and interlace

video output.

(Tuner mode)

Stores the current station in the memory.

MEMORY (U.K., Europe, Australia and

General models)

(Tuner mode)

Stores the current station in the memory.

9 DISC DIRECT (AUTO/MAN’L)

(DVD mode)

Changes the modes of DISC DIRECT function.

(Tuner mode)

Switches the tuning mode between automatic and manual.

(U.K., Europe, Australia and General models)

5

CONTROLS AND FUNCTIONS

INTRODUCTION

English

0 INPUT H/G

Selects the input source you want to listen to or watch.

q INPUT MODE

Sets the priority for the types of input signals (AUTO,

DTS, ANALOG) to receive when one component is

connected to two or more input jacks.

w DSP H/G

Selects the DSP program.

e STEREO

Switches between normal stereo and DSP effect

reproduction. When STEREO is selected, 2-channel

signals are directed to the front left and right speakers

without effect sounds.

r VOLUME +/–

Controls the output level of all audio channels.

This does not affect the recording (Rec) level.

t Remote control sensor

Receives signals from the remote control.

y Front panel display

Shows information about the operational status of this

unit.

u

SILENT

Allows you enjoy DSP effect for private listening with

headphones. When you connect headphones, no signals

are output to the speakers.

6

CONTROLS AND FUNCTIONS

Remote control (AMP mode)

This section explains the function of each button on the

remote control when you operate this unit as an amplifier,

not as a tuner or a DVD player. Make sure that the AMP

mode is selected before starting operation.

Refer to “REMOTE CONTROL (DVD MODE)” on page

31 for the details about the functions of the remote

control when you control this unit in the DVD mode.

Also, refer to “OPERATING OTHER COMPONENTS

USING THE REMOTE CONTROL” on pages 57 and 58

for the details about its functions when controlling other

components connected to this unit.

y

• The buttons on the remote control whose names are written in

purple are operation buttons when you operate this unit in the

AMP mode.

TV

CH

INPUT

TUNER

MUTE CD–R

VCR

VIDEO 2

VIDEO 1

MD

AV

SLEEP

POWER

TV MODE

POWER

VOL

REC

AUDIO

SUBTITLE

SHIFT

CODE SET

1

HALL

2

JAZZ

SETUP

3

ROCK

ANGLE

4

ENTERTAINMENT

MARKER

5

SPORTS

6

MONO MOVIE

PLAY MODE

7

MOVIE 1

REPEAT

8

MOVIE 2

A–B

DVD

CD

AMP

9

/DTS

TOP MENU

LEVEL

MENU

SET MENU

TEST

ON SCREEN

B. BOOST

RETURN

0

SELECT

>

–

10

MATRIX 6.1

GROUP

CANCEL

STEREO

PAGE

MUTE

VOL

ABCDE

ENTER

PRESET

CH

PRESET

CH

1

3

4

5

6

7

t

r

e

w

q

0

9

8

2

AMP

(U.S.A. model)

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 Basic operation buttons

Used to operate the components selected with input

selector buttons.

3 CODE SET

Used when setting up the manufacturer code.

4 DSP program buttons

Select DSP programs for the AMP position. Press a

button repeatedly to select a DSP program within that

group.

5 LEVEL

Selects the effect speaker channel to be adjusted.

6 Cursor buttons (j, i, u, d)/ENTER

Select SET MENU items and change the settings on the

SETUP menu etc.

7 TEST

Outputs the test tone to adjust the speaker levels.

8 SLEEP

Sets the sleep timer.

9 POWER (

)

Turns this unit on, or set it to the standby mode.

0 Input selector buttons/AMP

Select the input source and set the remote control to

operate the selected source component. Sets the remote

control to the AMP mode for controlling this unit.

q STEREO

Switches between normal stereo and DSP effect

reproduction. When STEREO is selected, 2-channel

signals are directed to the front left and right speakers

without effect sounds and all Dolby Digital and DTS

signals (except the LFE channel) are mixed down to the

front left and right speakers.

w MUTE

Mutes the sound. Press again to restore the audio output

to the previous volume level.

e SET MENU

Selects the SET MENU mode.

r VOL +/–

Increases or decreases the volume level.

t B. BOOST

Turns BASS BOOST function on or off.

7

CONTROLS AND FUNCTIONS

INTRODUCTION

English

■ Using the remote control

30° 30°

Approximately 6 m (20 feet)

Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

8

CONTROLS AND FUNCTIONS

Front panel display (left)

This front panel display mainly displays the information related to the playback of discs.

PGM RND

GROUP TITLE TRACK CHAP D.MIX P.PCM MLT.CH

AB

–

DVD V CD

VIDEO

AUDIO

888888888888

1

2345

7

68 9

1 Play mode indicators

PGM: Programmed play / RND: Random play /

: Repeat play / A-B : Repeat A-B

2 Mode type indicators

GROUP: Group mode / TITLE: Title mode /

TRACK: Track mode / CHAP: Chapter mode

3 D.MIX (Down Mix)

Lights up when the currently playing multi-channel audio

track is mixed down into 2-channel.

4 P.PCM (Packed PCM)

Lights up while a P.PCM signal is input.

5 MLT.CH (Multi Channel)

Lights up while a multi-channel signal is output.

6 Disc type indicators

Indicates the type of disc. For example, DVD and AUDIO

lights up when playing a DVD-Audio disc.

7 w

Lights up during playback. Blinks while resume function

is working.

8 d

Lights up while playback is paused.

9 Multi-information display (left)

Shows various information such as title, chapter or track

number, elapsed playing time etc.

9

CONTROLS AND FUNCTIONS

INTRODUCTION

English

Front panel display (right)

88888888888888

MATRIX

VIRTUAL

SILENT

MOVIE THTR DTS

DOLBY DIGITAL PRO LOGIC

12

ENTERTAINMENT

DVD/CD VIDEO 1VIDEO 2 VCR

MD/CD–R TUNER

STEREO

AUTO

TUNED

PS PTY RT CT

PTY HOLD

MEMORY

SLEEP

MUTE

dB

ms

SP

PRE

B. BOOST

DIGITAL

PRO LOGIC

/

DSP

PCM

L

LFE

C R

RL RC RR

12345

6

7890

o

iuytewq

r

(U.K. and Europe models only)

1 Decoder indicators

Lights up when the t, g,

PRO LOGIC

/

or

MATRIX are activated.

2 VIRTUAL indicator

Lights up in the virtual cinema DSP mode.

3 Headphones indicator

Lights up when headphones are connected.

4 SP/PRE indicator

The indicator of the item selected in “9 SP/PRE OUT” on

the SET MENU lights up. (But it does not light up when

headphones are connected.)

5 SILENT indicator

Lights up when headphones are connected while the

digital sound field processor is on.

6 Input source indicator

Shows the current input source with a cursor.

7 STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

8 AUTO indicator

Shows that this unit is in the automatic tuning mode.

9 TUNED indicator

Lights up when this unit is tuned to a station.

0 MEMORY indicator

Flashes to show a station can be stored.

q DSP indicator

Lights up when you select DSP programs.

w v indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

e B. BOOST indicator

Lights up when BASS BOOST is ON. (But it does not

light up when headphones are connected.)

r DSP program indicators

The name of the selected DSP program lights up when

the ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2 or V/DTS SURROUND DSP program is

selected.

t Multi-information display (right)

Shows the current DSP program name and other

information when adjusting or changing settings.

y SLEEP indicator

Lights up while the sleep timer is on.

u MUTE indicator

Flashes while the MUTE function is on.

i Input channel indicator

Indicates the channel components of input signals being

received.

o RDS indicator (U.K. and Europe models)

The name(s) of the RDS data offered by the currently

received RDS station light(s) up.

PTY HOLD indicator lights up while searching for

stations in the PTY SEEK mode.

10

PREPARATION STEPS

In order to enjoy sound and video images with this sound

system, follow the procedures as described below. See

each page for details.

Installing batteries in the remote control (P.3)

Speaker setup (P.11)

• Speaker placement (P.11)

• Installing the speakers (P.12)

Connections (P.14 – 19)

• Connecting TV and audio/video components (P.14)

• Connecting the antennas (P.16)

• Connecting the speakers (P.17)

• Connecting the AC power cord (P.19)

• Turning on the power (P.19)

Adjusting speaker output levels (P.20)

Before connecting components

• Do not connect this unit or other components to the

mains power until all connections between the

components have been completed.

• Be sure all connections are made correctly, that is to

say, L (left) to L, R (right) to R, “+” to “+” and “–” to

“–”. Some components require different connection

methods and have different jack names. Refer to the

operation instructions for each component to be

connected to this unit.

• Insert the plugs properly. The speakers may not output

any sound or may output noise if they are not inserted

properly.

• The name of jack corresponds to input selector.

• The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage BEFORE

plugging into the AC main supply. Voltages are

220/240 V AC, 50 Hz. (General model)

After connecting components

• Check them again to make sure they are correct.

VOLTAGE SELECTOR

240V 220V

VOLTAGE SELECTOR

(General model)

11

PREPARATION

English

SPEAKER SETUP

This unit has been designed to provide the best sound-

field quality with a 5-speaker system, using front left and

right speakers, rear left and right speakers and a center

speaker.

The front speakers are used for the main source sound

plus effect sounds. The rear speakers are used for effect

and surround sounds. The center speaker is for the center

sounds (dialog, vocals, etc.).

Notes

• If you do not use any of effect speakers (rear and/or center),

change the settings of SPEAKER SET items at the SET MENU

(p.60) to designate the signals to other terminals you connect

speakers to.

• If you use speakers (with different tonal qualities) instead of

the included speakers, the tone of a moving human voice and

other types of sound may not shift smoothly. We recommend

that you use speakers from the same manufacturer or speakers

with the same tonal quality.

Speaker placement

Refer to the following diagram when you place the

speakers.

Front speakers

Place the front left and right speakers an equal distance

from the ideal listening position. The distance between

each speaker and each side of the video monitor should

also be the same.

Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible (such as directly over or under the

monitor) and centrally between the front speakers.

Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (6 feet) above the

floor.

Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the front speakers. Turn it

slightly toward the center of the room to reduce wall

reflections.

Note

• Although the speaker system in this unit is magnetically

shielded, it may still affect the color on the television monitor

when using this unit near the television. Adjust the relative

positions of this unit and the television if this happens.

Center speaker Front speaker (R)

Rear speaker (R)

Front speaker (L)

1.8 m (6 feet)

Subwoofer

Rear speaker (L)

12

SPEAKER SETUP

Installing the speakers

■ Placing the center speaker

Place the speaker on TV whose top is flat or on the floor

under the TV or inside the TV rack so that it is stabilized.

When placing the speaker on top of the TV, to prevent the

speaker from falling down, put the provided fasteners at

four points on the bottom of the speaker and the top of the

TV.

Cautions

• Do not place the speaker on top of the TV whose area is

smaller than the bottom area of the speaker. If placed, the

speaker may drop out causing an injury to you.

• Do not place the speaker on top of the TV with an inclination.

• Do not touch the adhesive surface after peeling off the seal as

this will weaken its adhesive strength.

• Thoroughly wipe clean the surface where the fastener is to be

applied. Note that adhesive strength is weakened if the surface

is dirty, oily or wet and that this may cause the center speaker

to drop.

■ Placing the front and rear

speakers

When placing the front and rear speakers on a flat

surface, attach the included non-skid pads to the corners

on the bottom of the speakers as shown below. This

prevents the speakers from sliding around.

Peel off the

seal

Fastener

■ Mounting the front and rear

speakers

When mounting the front and rear speakers on a wall, use

the holes on the speakers’ back panels.

1 Put the provided pads at the four corners on

the rear of the front and rear speakers to

prevent the front and rear speakers from

moving by vibrations.

2 Fasten screws into a firm wall or wall

support as shown below.

Diam. 3.5 to 4 mm

Min.

20 mm

6 mm

Tapping screw

(Available at the

hardware store)

Non-skid pads

13

SPEAKER SETUP

PREPARATION

English

3 Hang the holes on the protruding screws.

• Make sure that the screws are securely caught by

the narrow parts of the holes.

• You can use the lower holes on the rear of the

front/rear speakers.

Cautions

• Each speaker weighs 1.1 kg (2 lbs. 6 oz.). Do not mount them

on thin plywood or a wall with soft surface material. If

mounted, the screws may come out of the flimsy surface and

the speakers may fall. This damages the speakers or causes

personal injury.

• Do not install the speakers to a wall with nails, adhesives, or

any other unstable hardware. Long-term use and vibrations

may cause them to fall.

• To avoid accidents resulting from tripping over loose speaker

cables, fix them to the wall.

• Select a proper position on the wall to mount the speaker so

that no one will injure his/her head or face.

60 mm

■ If you want to mount a speaker

on a commercially available

speaker stand (for the front/rear

speakers)

The screw holes (at an interval of 60 mm) on the bottom

and the rear of the speaker can be used to mount the

speaker on a speaker stand.

* Those screw holes can be used with M4 screws only.

60 mm

Front/rear speaker

(bottom)

60 mm

Front/rear speaker

(rear)

14

CONNECTIONS

Connecting TV and audio/video

components

■ Types of video jacks

1 COMPONENT VIDEO jacks (U.S.A., Canada,

Australia and General models)

Transmit color difference (PB/CB, PR/CR) and luminance

separately and provide the best quality picture.

2 VIDEO jack

Conventional composite video signal.

3 S VIDEO jack

Transmits color and luminance separately and achieves

high-quality color reproduction.

Notes

• Each type of video jack works independently. Signals input

through the composite video and S video jacks are only output

through the corresponding composite video and S video jacks.

• When you connect this unit to a video monitor, a video

component and a recording component, connect the same types

of jack, for example, the video jack on this unit to the video

jack on the video component.

• The description of the component video jacks may differ

depending on the component (e.g. Y, CB, CR/Y, PB, PR/Y, B-Y,

R-Y etc.). When using these jacks, refer also to the operation

instructions for the component being connected.

• Do not connect this unit to a video monitor through a video

cassette recorder. If you do so, the picture may not be played

back properly due to the copyright protection technology

incorporated in this unit.

• When progressive output (p.38) is selected in the DVD mode,

video signals are only output from the component video jacks.

321

PR PB Y

■ Types of audio jacks

1 COAXIAL jack

Connects a coaxial pin cable and provides the better

quality sound than analog audio jacks.

2 OPTICAL jack

Connects an optical fiber cable and provides the better

quality sound than analog audio jacks.

3 Analog audio jacks

Connect an audio pin cable.

y

• 1 and 2 are digital jacks.

• You can use the digital jacks to input PCM, Dolby Digital and

DTS bitstreams.

• All digital input jacks are acceptable for 96-kHz sampling

digital signals.

Notes

• Digital output jack and analog OUT (Rec) jacks are

independent. Only digital signals are output from digital output

jack and analog signals from OUT (Rec) jacks.

• The OPTICAL jacks on this unit conform to the EIA standard.

If you use an optical cable that does not conform to this

standard, this unit may not function properly.

• Once you have connected a recording component to this unit,

keep its power turned on while using this unit. If the power is

off, this unit may distort the sound from other components.

Anti-dust cap

Remove the cap covering the OPTICAL jacks when

connecting an optical cable. Safely store the cap and

always re-insert it in the terminal when the terminal is not

in use. (This cap prevents the entrance of dust.)

1 23

L

R

Anti-dust cap

104_S100_10-20_EN 02.5.13, 1:27 PM14

15

CONNECTIONS

PREPARATION

English

■ The connection example

Use a cable specified for connecting each type of jacks.

(The included video pin cable is used for connecting this unit to a video monitor.)

The connection example shown below is just an example. Connect in accordance with the components you have.

y

• The solid lines indicate the output from this unit and the dotted lines indicate the input to this unit.

For Audio component

Audio pin cable

Coaxial cable

Optical cable

For A/V component

Audio/Video cable

For Video Component

Video pin cable (included)

S Video cable

Component video cable

(U.S.A., Canada, Australia and General

models)

FM ANT

75ΩUNBAL.

GND – AM ANT

P

R

P

B

Y

L

IN

VIDEO 1 VIDEO 2

VIDEO

VCR

IN IN

IN IN IN

OUT OUT

IN IN IN INOUT OUT

OUT OUT

S VIDEO

MONITOR

MD/CD-R FRONT CENTER

SYSTEM

MONITOR

6CH PREOUT

VIDEO 1 VIDEO 2 VCR

REAR

SUBWOOFER

R

MD/CD-R

COMPONENT VIDEO OUT

OPTICAL

OUT

CONNECTOR

MARK

TO SW-S100

[

B

]

[

A

]

COAXIAL

IN

OPTICAL

IN

MD/CD-R VIDEO 1

DIGITAL

ANALOG

S VIDEO

INPUT

VIDEO

AUDIO

L

R

S VIDEO

OUTPUT

VIDEO

AUDIO

L

R

S VIDEO

INPUT

VIDEO

COMPONENT

VIDEO

S VIDEO

OUTPUT

OPTICAL

AUDIO

L

VIDEO

R

INPUT

OPTICAL

AUDIO

L

R

OUTPUT

COAXIAL

AUDIO

L

R

P

B

/C

B

P

R

/C

R

Y

S Video cable

Video pin cable (included)

Component video cable

(U.S.A., Canada, Australia and General

models)

Video monitor

S Video cable

Audio/Video

cable

VCR

S Video cable

Audio/Video cable

(U.S.A. model)

Coaxial cable

Audio pin cable

Optical cable

CD recorder or MD recorder

Audio pin cable

S Video cable

Optical cable

Audio/Video cable

TV/digital TV/cable TV

104_S100_10-20_EN 02.5.13, 1:28 PM15

16

CONNECTIONS

Connecting the antennas

Both AM and FM indoor antennas are included with this

unit. In general, these antennas should provide sufficient

signal strength.

Connect each antenna correctly to the designated

terminals.

■ Connecting indoor FM antenna

Connect the included indoor FM antenna to the FM ANT

terminal.

75ΩUNBAL.

FM ANT GND – AM ANT

Ground (GND terminal)

For maximum safety and

minimum interference, connect

the antenna GND terminal to a

good earth ground. A good earth

ground is a metal stake driven into

moist earth.

Indoor FM antenna

(included)

AM loop antenna

(included)

■ Connecting the AM loop antenna

1 Set up the AM loop antenna, then connect it.

2 Press and hold the tab to insert the AM loop

antenna lead wires into the AM ANT and

GND terminals.

3 Release the tab. (The tab will return to its

original position when you release your

finger.)

Once connected, pull the wires gently to check that

they are connected securely.

4 Orient the AM loop antenna for the best

reception.

y

• A properly installed outdoor antenna provides clearer reception

than an indoor one. If you experience poor reception quality, an

outdoor antenna may improve the quality. Consult the nearest

authorized YAMAHA dealer or service center about the

outdoor antennas.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

Bare wire

Tab

Страница загружается...

Yamaha DVX-S100, AVXS100, NX-S100S Руководство пользователя

Похожие модели бренда

Модели других брендов