Simplicity 040495-00 Руководство пользователя

Operator’s Manual

Generating Set

EAC

80010733

Revision ( B )

2

Thank you for purchasing this quality-built Briggs & Stratton® generating set. We’re pleased that you’ve placed

your confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this

manual, your generating set will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with generating

sets and how to avoid them. Because we do not necessarily know all the applications this equipment could be

used for, it is important that you read and understand these instructions thoroughly before attempting to start or

operate this equipment. Save these original instructions for future reference.

This generating set requires professional installation before use. Refer to the separate installation manual

for full information. Your installer should follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generating set. There are many

Briggs & Stratton authorized service providers worldwide who provide quality service. You can also contact Briggs

& Stratton Customer Service by phone at 800-732-2989 between 8:00 AM and 5:00 PM CT., or by e-mail at

[email protected], or click on Find a Dealer at BRIGGSandSTRATTON.COM, which provides a list

of authorized dealers.

Generating set and engine model and serial numbers should be recorded in the installation manual.

Original Instructions (English)

3

Table of Contents

Important Safety Instructions .....................4

Installation .....................................7

For the Owner:........................................... 7

For the Installing Dealer/Contractor: ......................... 7

Owner Orientation ........................................ 7

Fuel Factors ............................................. 8

Generating Set Location ................................... 9

Delivery Inspection ...................................... 10

Controls.......................................11

Access Ports ........................................... 13

System Control Panel .................................... 15

Operation .....................................19

Engine Oil.............................................. 19

Battery ................................................ 19

15 Amp Fuse ........................................... 19

Overload Protection Fuse ................................. 19

Automatic Operation Sequence ............................ 19

Setting Exercise Timer ................................... 20

Maintenance ...................................21

Servicing the System..................................... 21

Service Code Detection System ........................... 21

Maintenance Schedule ..........................23

Generating Set Maintenance .....................23

Battery ................................................ 24

Engine Maintenance ..................................... 24

Engine Oil.............................................. 25

Service Air Cleaner ...................................... 26

Fuel System Inspection and Maintenance ................... 27

Exhaust System Maintenance and Inspection ................ 27

Engine Exterior ......................................... 27

Service Spark Plugs ..................................... 27

When Calling for Assistance............................... 27

Storage................................................ 27

Troubleshooting................................28

Generating Set Specifications ....................30

Engine Specifications ...........................30

4

Save These Instructions

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual

contains important instructions that should be followed

during installation and maintenance of the generating

set and batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential

personal injury hazard. A signal word (DANGER,

WARNING, or CAUTION) is used with the alert symbol

to designate a degree or level of hazard seriousness.

A safety symbol may be used to represent the type of

hazard. The signal word NOTICE is used to address

practices not related to personal injury.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE addresses practices not related to personal

injury.

The manufacturer cannot possibly anticipate every

possible circumstance that might involve a hazard.

The warnings in this manual, and the tags and decals

affixed to the unit are, therefore, not all-inclusive.

If you use a procedure, work method or operating

technique that the manufacturer does not specifically

recommend, you must satisfy yourself that it is safe

for you and others. You must also make sure that the

procedure, work method or operating technique that

you choose does not render the generating set system

unsafe.

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide could result in

death, serious injury, headache, fatigue,

dizziness, vomiting, confusion, seizures,

nausea or fainting.

• Operate this product ONLY outdoors in an area that

will not accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open

garage doors or other openings that can allow

exhaust gas to enter inside or be drawn into a

potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed

and maintained indoors according to the

manufacturer’s instructions/recommendations.

Smoke alarms cannot detect carbon monoxide gas.

WARNING Storage batteries give off explosive

hydrogen gas during recharging.

Slightest spark will ignite

hydrogen and cause explosion,

resulting in death and/or serious

injury.

Battery electrolyte fluid contains

acid and is extremely caustic.

Contact with battery

contents could cause severe

chemical burns.

A battery presents a risk of

electrical shock and high short

circuit current.

• DO NOT dispose of battery in a fire. Recycle

battery.

• DO NOT allow any open flame, spark, heat, or

lit cigarette during and for several minutes after

charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, rubber

boots and rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

NOTICE Only qualified, licensed electricians should

attempt installation of this equipment, which must

strictly comply with applicable codes, standards and

regulations.

Fire

Toxic Fumes

Explosive Pressure

Lift Hazard Read Manual

Chemical BurnAuto Start

Hot SurfaceRotating Parts

Electrical ShockExplosion

5

WARNING Generating set produces hazardous

voltage.

Failure to properly ground generating set

could result in electrocution.

Failure to isolate generating set from utility

power could result in death or serious injury

to electric utility workers due to backfeed of

electrical energy.

• Electrical system must meet current requirements

when generating set is installed. This includes the

RCD in distribution panel.

• DO NOT touch bare wires or bare receptacles.

• DO NOT use generating set with electrical cords

which are worn, frayed, bare or otherwise damaged.

• DO NOT handle generating set or electrical cords

while standing in water, while barefoot, or while

hands or feet are wet.

• If you must work around a unit while it is operating,

stand on an insulated dry surface to reduce the risk

of a shock hazard.

• DO NOT allow unqualified persons or children to

operate or service generating set.

• In case of an accident caused by electrical shock,

immediately shut down the source of electrical

power and contact the local authorities. Avoid

direct contact with the victim.

• Despite the safe design of the generating set,

operating this equipment imprudently, neglecting its

maintenance or being careless could cause possible

injury or death.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you

are physically or mentally fatigued.

• Before performing any maintenance on the

generating set, disconnect the battery cable

indicated by a NEGATIVE, NEG or (-) first. When

finished, reconnect that cable last.

• After your system is installed, the generating set

may crank and start without warning any time there

is a power failure. To prevent possible injury, always

set the generating set’s system switch to OFF,

remove the service disconnect from the disconnect

box AND remove the 15 Amp fuse BEFORE

working on the equipment.

WARNING Hazardous Voltage - Contact with

power lines could cause electric shock

or burns, resulting in death or serious

injury.

Lifting Hazard / Heavy Object - Could

result in serious injury.

• If lifting or hoisting equipment is used, DO NOT

contact any power lines.

• DO NOT lift or move generating set without

assistance.

• Use lifting pipes as described in Lifting the

Generating Set.

• DO NOT lift unit by roof as damage to generating

set will occur.

WARNING Propane and Natural Gas are

extremely flammable and explosive,

which could cause burns, fire or

explosion resulting in death and/or

serious injury.

• Install the fuel supply system according applicable

fuel-gas codes.

• Before placing the generating set into service, the

fuel system lines must be properly purged and leak

tested.

• After the generating set is installed, you should

inspect the fuel system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or

other explosive conditions exist.

• DO NOT smoke around the generating set. Wipe

up any oil spills immediately. Ensure that no

combustible materials are left in the generating set

compartment. Keep the area near the generating set

clean and free of debris.

6

NOTICE Improper treatment of generating set could

damage it and shorten its life.

• Use generating set only for intended uses.

• If you have questions about intended use, contact

your authorized dealer.

• Operate generating set only on level surfaces.

• Adequate, unobstructed flow of cooling and

ventilating air is critical to correct generating set

operation.

• The access panels/doors must be installed

whenever the unit is running.

• DO NOT expose generating set to excessive

moisture, dust, dirt, or corrosive vapors.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you

are physically or mentally fatigued.

• DO NOT start engine with air cleaner or air cleaner

cover removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generating set or any of its parts as

a step. Stepping on the unit could cause stress and

break parts. This may result in dangerous operating

conditions from leaking exhaust gases, fuel leakage,

oil leakage, etc.

• If connected devices overheat, turn them off and

disconnect them from generating set.

Shut off generating set

and contact an authorized dealer

if

- electrical output is lost;

- equipment sparks, smokes, or emits flames;

- unit vibrates excessively;

- unit makes unusual noises.

WARNING Starter and other rotating parts could

entangle hands, hair, clothing, or accessories

resulting in serious injury.

• NEVER operate generating set without protective

housings, covers, or guards in place.

• DO NOT wear loose clothing, jewelry or anything

that could be caught in the starter or other rotating

parts.

• Tie up long hair and remove jewelry.

• Before servicing, remove 15 Amp fuse from control

panel and disconnect Negative (NEG or -) battery

cable.

WARNING

Exhaust heat/gases could ignite

combustibles or structures resulting in

death and/or serious injury. Contact with

muffler area could cause burns resulting

in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust

gases.

• Allow equipment to cool before touching.

• Exhaust outlet side of weatherproof enclosure must

have at least 1.5 m minimum clearance from any

structure, shrubs, trees or any kind of vegetation.

• Weatherproof enclosure must be at least 1.5 m

from windows, doors, any wall opening, shrubs or

vegetation over 30.5 cm in height.

• Weatherproof enclosure must have a minimum

of 1.5 m overhead clearance from any structure,

overhang or trees.

• DO NOT place weatherproof enclosure under a

deck or other type of structure that may confine

airflow.

• Use only flexible fuel line provided. Connect

provided fuel line to generating set, DO NOT use

with or substitute any other flexible fuel line.

• Smoke detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Carbon monoxide

alarms cannot detect smoke.

• Keep at least minimum distances shown in General

Location Guidelines to insure for proper generating

set cooling and maintenance clearances.

• To use or operate the engine on any forest-covered,

brush-covered, or grass-covered land, contact the

original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust

system installed on this engine.

• Replacement parts must be the same and installed

in the same position as the original parts.

CAUTION Installing the 15 Amp fuse could cause

the engine to start at any time without warning

resulting in minor or moderate injury.

• Observe that the 15 Amp fuse has been removed

from the control panel for shipping.

• DO NOT install this fuse until all plumbing and wiring

has been completed and inspected.

CAUTION Excessively high operating speeds

could result in minor injury.

Excessively low speeds impose a heavy load on

generating set.

• DO NOT tamper with governed speed. Generating

set supplies correct rated frequency and voltage

when running at governed speed.

• DO NOT modify generating set in any way.

7

Installation

We sincerely appreciate your patronage. For this

reason, we have made every effort to provide for

a safe, streamlined and cost-effective installation.

Because each installation is unique, it is impossible

to know of and advise the trade of all conceivable

procedures and methods by which installation might be

achieved. Neither could we know of possible hazards

and/or the results of each method or procedure.

For these reasons, only current licensed electrical

and plumbing professionals should attempt

generating set system installations. Installations

must strictly comply with all applicable codes,

industry standards and regulations.

Your generating set is supplied with this “Operator’s

Manual” and a separate “Installation Manual.” These

are important documents and should be retained by

the owner after the installation has been completed.

For the Owner:

To help you make informed choices and communicate

effectively with your installation contractor(s), read

and understand Owner Orientation in this manual

before contracting or starting your generating

set installation.

To arrange for proper installation, contact the store at

which you purchased your generating set, your dealer,

a licensed electrician or your utility power provider.

The generating set warranty is VOID unless the

system is installed by licensed electrical and

plumbing professionals.

Every effort has been made to ensure that information

in this manual is accurate and current. However, we

reserve the right to change, alter, or otherwise improve

the product and this document at any time without prior

notice.

For the Installing Dealer/Contractor:

For most applications, the installation manual contains

all the information required to properly install and start

the generating set. This operator’s manual describes

routine operation and owner maintenance procedures.

Owner Orientation

This section provides generating set owners with the

information necessary to achieve the most satisfactory

and cost effective installation possible.

The illustrations are for typical circumstances and

are meant to familiarize you with the installation

options available with your generating set. A

thorough understanding of these options will provide

fundamental control over the cost of your installation,

as well as ensure your final satisfaction and security.

Federal and local codes, appearance, noise levels,

fuel types, and distances are the factors that must

be considered when negotiating with an installation

professional. Remember that as the distance from the

existing electrical service and gaseous fuel supply

increases, and the number of 90 degree bends in the

fuel supply increases, compensations in piping and

wiring materials must be made. This is necessary

to comply with local codes and overcome electrical

voltage drops and gaseous fuel pressure drops.

The factors mentioned above will have a direct

affect on the overall price of your generating set

installation.

In some areas you may need to acquire electrical

permits for installing the generating set, building

permits for installing gas lines, and permits for noise

allowances. Your installer should check your local

codes AND obtain the permits before installing the

system.

8

Fuel Factors

An important consideration affecting the entire

installation is the type of fuel used by your generating

set. The system was factory tested and adjusted

using either natural gas or liquid propane (LP

vapor). For proper engine function, factors that are

inherent to each of these fuels, your location and the

duration of possible utility interruptions are important

considerations in the following fuel guidelines:

• Use clean, dry fuel, free of moisture or any

particulate material. Using fuels outside the

following recommended values may cause

performance problems.

• In engines set up to run on propane (LP),

commercial grade HD5 propane with a minimum

fuel energy of 93 MJ/m

3

at standard temperature

and pressure, with maximum propylene content of

5% and butane and heavier gas content of 2.5%

and minimum propane content of 90%.

Natural gas rating will depend on specific fuel but

typical derates are between 10 to 20% off the LP gas

rating.

Natural gas or LP engines are certified to operate on

natural or liquid propane gas. The emissions control

system for this engine is EM (Engine Modifications).

Power Decrease at High Altitude or High

Temperature

Air density is less at high altitudes, resulting in less

available engine power. Specifically, engine power

will decrease 3.5% for each 300 meters above sea

level and 1% for each 5.6°C above 25°C. Make sure

you and your installer consider these factors when

determining total generating set load.

WARNING Propane and Natural Gas are

extremely flammable and explosive,

which could cause burns, fire or

explosion resulting in death or serious

injury.

• DO NOT operate the equipment if the emergency

“fuel shut-off” valve is missing or inoperative.

• After the generating set is installed, you should

inspect the fuel system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or

other explosive conditions exist.

• DO NOT smoke around the generating set. Wipe

up any oil spills immediately. Ensure that no

combustible materials are left in the generating set

compartment. Keep the area near the generating

set clean and free of debris.

9

Generating Set Location

The actual physical location of your generating set has

a direct affect on:

1. The amount of plumbing required to fuel

your generating set.

2. The amount of wiring required to control and

connect your generating set.

Specific location guidelines are discussed in the

installation manual. Acquaint yourself with that

information and confer with your installer. Be sure to

ask how your site might affect installation costs and

compliance with local codes and standards.

• Install generating set outdoors in an area that will

not accumulate deadly exhaust gas.

• DO NOT install generating set where exhaust gas

could accumulate and enter inside or be drawn

into a potentially occupied building or structure.

• It may be required to have a Carbon Monoxide

(CO) detector in operating condition in your

home. Carbon monoxide detector(s) (A) MUST

be installed and maintained indoors according to

the manufacturer’s instructions/recommendations.

A CO monitor is an electronic device that detects

hazardous levels of CO. When there is a buildup

of CO, the monitor will alert the occupants by

flashing visual indicator light and alarm. Smoke

alarms cannot detect CO gas.

• Ensure exhaust gas is kept away from any

windows, doors, ventilation intakes, soffit vents,

crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter

inside or be drawn into a potentially occupied

building or structure. Your neighbor’s may

be exposed to the engine exhaust from your

generating set and must be considered when

installing the unit.

• Wind and air currents should be taken into

consideration when positioning the unit.

See the installation manual for full details on safe

generating set location.

A

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide could result in

death, serious injury, headache, fatigue,

dizziness, vomiting, confusion, seizures,

nausea or fainting.

• Operate this product ONLY outdoors in an area that

will not accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open

garage doors or other openings that can allow

exhaust gas to enter inside or be drawn into a

potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed

and maintained indoors according to the

manufacturer’s instructions/recommendations.

Smoke alarms cannot detect carbon monoxide gas.

WARNING Exhaust heat/gases could ignite

combustibles or structures resulting in death

or serious injury.

• Exhaust outlet side of weatherproof enclosure must

have at least 1.5 m minimum clearance from any

structure, shrubs, trees, or any kind of vegetation.

• Weatherproof enclosure must be at least 1.5 m

from windows, doors, any wall opening, shrubs or

vegetation over 30.5 cm in height.

• Weatherproof enclosure must have a minimum

of 1.5 m overhead clearance from any structure,

overhang or trees.

• DO NOT place weatherproof enclosure under a

deck or other type of structure that may confine

airflow.

• USE ONLY flexible fuel line provided. Connect

provided fuel line to generating set. DO NOT use

with or substitute any other flexible fuel line.

• Smoke detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Carbon monoxide

alarms cannot detect smoke.

• DO NOT place weatherproof enclosure in manner

other than shown in illustrations.

10

Delivery Inspection

Carefully inspect the generating set for any damage

that may have occurred during shipment.

If loss or damage is noted at time of delivery, have

the person(s) making delivery note all damage

on the freight bill and affix his signature under the

consignor’s memo of loss or damage. If loss or

damage is noted after delivery, separate the damaged

materials and contact the carrier and your installer for

claim procedures. Missing or damaged parts are not

warranted.

The home generating set system is supplied with:

• Oil (5W30 Synthetic)

• Flexible steel fuel line

• Installation and start-up manual

• Operator’s manual

• Spare access keys

• Spare 15 Amp ATO-type fuse

Not included:

• Carbon monoxide detector(s)

• Smoke detector(s)

• Starting battery

• Connecting wire and conduit

• Fuel supply valves/plumbing

• Crane, lifting straps, chains or cables

• Two 1.2 meter lengths of 25 mm pipe, 3.3 mm

minimum thickness (NOT conduit)

• Hole punches for 1.6 mm steel

• Torque screwdriver, 0.5 to 5 Nm range

• Voltage / frequency meter

• Various special tools and equipment

• Remote wireless monitor (OPTIONAL)

• Antenna (OPTIONAL)

11

Controls

6kVA Generating Set

Read this Operator’s Manual and Important Safety Instructions before operating your generating set.

Compare the illustrations with your generating set to familiarize yourself with the locations of various

controls and adjustments. Save this manual for future reference.

Generating set is shown with roof and access covers

removed for clarity.

(A) - Lifting Holes — Provided at each corner for

lifting generating set.

(B) - Exhaust Port — High-performance muffler lowers

engine noise to comply with most residential

codes.

(C) - Alternator — An electrical machine that

generates an alternating current.

(D) - Spark Plug — A device in the cylinder head of

the engine that ignites the fuel mixture by means

of an electric spark.

(E) - Air Cleaner — Uses a dry type filter element and

foam precleaner to protect engine by filtering dust

and debris out of intake air.

(F) - Control Panel — Used for various test, operation

and maintenance functions. See System Control

Panel.

(G) - Circuit Breaker — Protects the system from

shorts and other over-current conditions.

(H) - Battery (installer supplied) — 12 Volt DC, top-

post automotive style battery provides power to

start the engine.

(J) - Fuel Inlet Port — Attach appropriate fuel supply

to generating set here.

A

B

C

D

F

H

J

E

G

12

8kVA Generating Set

Read this Operator’s Manual and Important Safety Instructions before operating your generating set.

Compare the illustrations with your generating set to familiarize yourself with the locations of various

controls and adjustments. Save this manual for future reference.

Generating set is shown with roof and access covers

removed for clarity.

(A) - Lifting Holes — Provided at each corner for

lifting generating set.

(B) - Exhaust Port — High-performance muffler lowers

engine noise to comply with most residential

codes.

(C) - Alternator — An electrical machine that

generates an alternating current.

(D) - Spark Plug — A device in the cylinder head of

the engine that ignites the fuel mixture by means

of an electric spark.

(E) - Air Cleaner — Uses a dry type filter element and

foam precleaner to protect engine by filtering dust

and debris out of intake air.

(F) - Control Panel — Used for various test, operation

and maintenance functions. See System Control

Panel.

(G) - Circuit Breaker — Protects the system from

shorts and other over-current conditions.

(H) - Battery (installer supplied) — 12 Volt DC, top-

post automotive style battery provides power to

start the engine.

(J) - Fuel Inlet Port — Attach appropriate fuel supply

to generating set here.

A

B

C

D

F

H

J

E

G

13

Access Ports

The generating set is equipped with an enclosure that

has several access panels, as shown.

NOTICE The generating set roof must be removed to

gain access to the front panel.

(A) Front Panel that is used to access:

• Battery Compartment

• Engine Oil Drain Hose

• Engine Oil Filter

• Engine Valve Cover

• Spark Plugs

Each generating set is shipped with a set of identical

keys.

A

14

To remove roof:

1. Remove the five screws (A) that secure the roof

to the unit.

2. Carefully lift and remove roof from unit.

To remove front panel:

1. Remove the two screws (B) that secure the panel to

the unit.

2. Lift and flex panel outward and off base. Use

caution not to damage the battery box (C).

To secure front panel:

1. Place panel in unit.

2. Secure the panel with two screws.

C

B

15

System Control Panel

The generating set control panel, located inside the

generating set housing, is shown below.

Brief descriptions of the controls used during

installation are:

The generating set control board, located inside the

generating set, under the roof, is shown below. Brief

descriptions of the controls used during installation are:

A - Menu/Programming Navigation Buttons — See

Menu section for details

B - USB Port — Authorized Dealer Service Use Only

C - Generating set Operation Control Buttons —

•“AUTO” Normal operating position. Press and

hold button to put unit into Automatic mode. If

an utility power outage is sensed, the system

will start the generating set. When utility power

is restored, auto lets the engine stabilize internal



waits for the next utility outage.

•“OFF” 

unit from starting, and resets any detected faults.

OFF must be pressed and held for more than 5

seconds in order to reset service codes.

•“MANUAL” Used to manually start the generating

set.

“AUTO” LED — LED will light when unit is placed

into Auto mode. LED will blink if exercise cycle is

not set or set to OFF.

D - 15 Amp Fuse — Protects the generating set DC

control circuits. If the fuse has ‘blown’ (melted

open) or was removed, the engine cannot crank

or start. Replace the fuse using only an identical

ATO 15A fuse. One spare fuse is supplied with

the unit.

E - Cover — This protective cover must be opened to

access the fuse and the USB port.

F - Digital Display — Displays generating set mode,

menu options, service codes, and service engine

indicators

More information may be found in Controls in the

operator’s manual.

A

B

C

F

E

D

16

Menu

MENU

ENTER THE MENU (VIEW SETTINGS)

PRESS TO CONFIRM SELECTION WHEN PROGRAMMING.

ESCAPE (EXIT) RETURN TO LAST MENU ITEM

RIGHT ARROW

TOGGLE THROUGH MENU OPTIONS

SETTING SYSTEM PARAMETERS

LEFT ARROW

TOGGLE THROUGH MENU OPTIONS

SETTING SYSTEM PARAMETERS

MANUAL MODE

USED TO MANUALLY START THE GENERATING SET. PRESS AND

HOLD BUTTON TO START THE GENERATING SET.

OFF

TURNS OFF RUNNING GENERATING SET, PREVENTS UNIT FROM

STARTING, AND RESETS ANY DETECTED FAULTS.

AUTOMATIC MODE

NORMAL OPERATING POSITION. PRESS AND HOLD BUTTON TO

PUT UNIT INTO AUTOMATIC MODE. IF A UTILITY POWER OUTAGE

IS SENSED, THE

SYSTEM WILL START THE Generating set. WHEN UTILITY POWER

IS RESTORED, AUTO LETS THE ENGINE STABILIZE INTERNAL

TEMPERATURES, SHUTS OFF THE Generating set, AND WAITS

FOR THE NEXT UTILITY POWER OUTAGE.

GENERAL

SET-UP

PRESS AND HOLD [ARROW LEFT AND ARROW RIGHT]

FOR THREE SECONDS TO ENTER THE PROGRAM

MODE.

ADVANCED

SETTINGS

PRESS AND HOLD [ARROW LEFT, ARROW RIGHT AND

ESC] FOR THREE SECONDS TO ENTER THE ADVANCED

SETTINGS MODE.

WIRELESS

LINK MODE

PRESS AND HOLD [MENU AND ESC] FOR THREE

SECONDS TO ENTER THE WIRELESS LINKING MODE.

The following chart shows the icons for the buttons that control the system control panel.

The following chart describes key sequences for accessing different programming modes;

17

General Set Up Screen

For general set up, press and hold the left arrow and right arrow for 3 seconds. Follow the prompts as

outlined below.

NOTE: Date and Time were set at the factory and stored in the control panel memory. The Exercise Cycle was

also set at the factory. The default exercise cycle occurs on Tuesdays, at 2:00 P.M. Central Standard Time. To

update or change these settings, follow the steps below.

IF DURING PROGRAMMING NO BUTTONS ARE PRESSED FOR 30 SECONDS,

THE CONTROL PANEL WILL AUTOMATICALLY EXIT THE PROGRAM MODE.

SET DATE

If set to OFF, display will read:

EXERCISE CYCLE OFF

or

YEAR

FLASHING

MONTH

FLASHING

DAY##

FLASHING

SET TIME

HOURS

FLASHING

MINUTES

FLASHING

AM/PM

FLASHING

or or or

or

or or or

or

or or or or

DAY OF

WEEK

FLASHING

HOURS

FLASHING

MINUTES

FLASHING

AM/PM

FLASHING

SET EXERCISE

CYCLE

EVENT LOG

Display will scroll last service code event, date, time,

and ambient temperature of when the event occurred.

or

OFF

18

Control Panel Prompts

Automatic Mode

In Automatic Mode, the display screen will display via

scrolling text:

• Generating set READY - if the unit is in standby and

utility power is present.

• Generating set ON - if the unit is running and utility

power is not present.

• SERVICE CODE - if a system fault has been detected.

General System Parameters

To view general system parameters, press the MENU

button.

The following will scroll across the digital display and then

move to the next item:

• Run time

• Date

• Time

• Exercise Cycle date and start time

The user can press the LEFT ARROW or RIGHT ARROW at

any time to move to the next item.

The user can press ESCAPE to go back to Generating set

READY.

If no user inputs are made for 10 seconds after all the items

have been displayed, the control board will reset to

Generating set READY.

AUTOMATIC MODE

GENERATOR READY OR SERVICE CODE

DESCRIPTION

(When Generator NOT Running - Auto Mode)

GENERATOR ON

(When Generator Running - Auto Mode)

(MENU)

RUN TIME

or

TIME

DATE

EXERCISE CYCLE

19

Operation

Important Owner’s Considerations

Engine Oil

The engine is shipped from the factory pre-run and

filled with synthetic oil (API SJ/CF 5W-30). This allows

for system operation in a wide range of temperature

and climate conditions. Before starting the engine,

check oil level and ensure that engine is serviced as

described in Maintenance.

Battery

The installer must supply a rechargeable 12 volt

DC starting battery. See Battery in Final Installation

Considerations in the installation manual.

With the battery installed, all wiring to transfer switch

and generating set completed, utility power supplied

to the automatic transfer switch, and the unit in

AUTO mode, the battery receives a trickle charge

while the engine is not running. The trickle charge

cannot be used to recharge a battery that is

completely

discharged.

15 Amp Fuse

The generating set’s 15 Amp fuse is critical to correct

system operation. The 15 Amp fuse was removed

at the factory to prevent the unit from starting during

shipping. Your installer will ensure the fuse is properly

installed upon completion of the installation.

Overload Protection Fuse

The generating set is protected by a fuse in series with

it’s excitation coil.

Automatic Operation Sequence

The generating set’s control board constantly monitors

utility voltage. Should utility voltage drop below a

preset level, the control board will signal the engine to

crank and start.

When utility voltage is restored above a preset voltage

level, the engine is signaled to shut down.

The actual system operation is not adjustable and

is sequenced by sensors and timers on the control

board, as follows:

Utility Voltage Dropout Sensor

• This sensor monitors utility source voltage.

• If utility source voltage drops below about

70 percent of the nominal supply voltage, the

sensor energizes a 3 second timer. The timer is

used to ‘sense’ brown-outs.

• Once the timer has expired, the engine will crank

and start.

Utility Voltage Pickup Sensor

This sensor monitors utility power voltage. When utility

voltage is restored above 80 percent of the nominal

source voltage, a time delay starts timing and the

engine will go to engine cool-down.

Engine Cool-down Timer

When utility power is sensed and the load transfers to

the utility source, the engine will go into a cool down

period as described below:

• If the generating set has run for MORE than

5 minutes, once the utility transfer occurs, the

engine will continue to run for about 1 minute

before shutting down.

• If the generating set has run for LESS than 5

minutes, once the utility transfer occurs, the

engine will continue to run until 5 minutes has

elapsed before shutting down.

NOTICE Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil will result in equipment failure.

• DO NOT attempt to crank or start the engine before

it has been properly serviced with the recommended

oil. This may result in an engine failure.

• Damage to equipment resulting from failure to follow

this instruction will void generating set warranty.

CAUTION With the system switch set to AUTO,

the engine could crank and start at any

time without warning, resulting in minor or

moderate injury.

• To prevent possible injury that may be caused by

such sudden starts, always set the system switch to

OFF if performing maintenance on the system.

• Remove the 15 Amp fuse before working on or

around the generating set or transfer switch.

20

Setting Exercise Timer

The generating set is equipped with an exercise

timer. During the exercise period, the unit runs for

approximately 20 minutes and then shuts down.

Electrical load transfer DOES NOT occur during the

exercise cycle (unless an utility power outage occurs).

The generating set will only enter the exercise cycle if

the unit is in the AUTO mode and this exact procedure

is followed.

To set the exercise timer:

NOTICE The generating set is preset with an exercise

cycle of Tuesday at 2:00 PM, Central Time. To change

the cycle setting, proceed to the following steps:

1. Choose the day and time you want your

generating set to exercise.

2. Press and hold the left arrow and right arrow

simultaneously for 3 seconds to enter the General

Set-Up program mode. See General Set-Up flow

chart in Menu Section.

3. Verify and/or set the time and date on the unit.

4. Go to the SET EXERCISE prompt and hit the “OK”

button.

NOTICE Items will flash until they are selected.

SELECT DAY: Use the left or right arrow to toggle

through the days of the week, Once the day is

selected, hit the “OK” button.

SELECT HOUR: Use the left or right arrow

to toggle through between 1 and 12. Choose

the hour of day you want the generating set to

exercise then hit the “OK” button.

SELECT MINUTE: Use the left of right arrow to

toggle between :00 and :59. Choose the minute

of the day you want the generating set to exercise

then hit the “OK” button.

SELECT AM/PM: Use the left of right arrow to

toggle between AM and PM. Once chosen, hit the

“OK” button.

NOTICE During the weekly exercise cycle, the

generating set will run for 20 minutes, but it will not

supply power to the home.

If you want to change the day and time the unit

exercises, simply perform the procedure again.

To turn off the generating set exercise cycle, go to

the OFF selection within the day of the week menu

and press OK. The display will then scroll: EXERCISE

CYCLE OFF.

Страница загружается ...

Simplicity 040495-00 Руководство пользователя

Это руководство также подходит для

Simplicity 040495-00 Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов