Zanussi ZGF648IX Руководство пользователя

ZGF 643 ITXC

ZGF 648 IR

ZGF 648 IX

User

Manual

Gas

Hob

RU

Pуководство

по

эксплуатации

Газовая

варочная

поверхность

2

3

Thank you for selecting our applianceThank you for selecting our appliance

Thank you for selecting our appliance

We wish you lots of enjoyment with your new appliance and we hope that

you will consider our brand again when purchasing household appliances.

Please read this user manual carefully and keep it throughout the product

life cycle as a reference document. The user manual should be passed on

to any future owner of the appliance.

4

Important safety information .............................................................................. 5

Operation .......................................................................................................... 7

Using the hob correctly ..................................................................................... 8

Cleaning and Maintenance ................................................................................ 9

Service and original spare parts ....................................................................... 20

European guarantee ........................................................................................ 20

For the User

For the Installer

Technical data ................................................................................................. 11

Installation ....................................................................................................... 13

Adaptation to different types of gas ................................................................. 15

Electrical connection ....................................................................................... 16

Building in ....................................................................................................... 17

Possibilities for insertion .................................................................................. 19

Contents

The following symbols will be found in the text to guide you throughout the

Instructions:

Safety Instructions

Step by step instructions for an operation

Hints and Tips

Environmental information

!

Guide to Use the instructions

This appliance complies with the following E.E.C. Directives:

• 2006/95 (Low Voltage Directive);

• 89/336 (Electromagnetical Compatibility Directive);

• 90/396 (Gas Appliances);

• 93/68 (General Directives)

and subsequent modifications.

MANUFACTURER:MANUFACTURER:

MANUFACTURER:

ELECTROLUX HOME PRODUCTS ITALY S.p.A.

Viale Bologna, 298

47100 FORLÌ (Italy)

5

Installation

" The work of installation must be

carried out by competent and qualified

installers according to the regulations

in force.

• Any modifications to the domestic

electrical mains which may be

necessary for the installation of the

appliance should be carried out only

by competent personnel.

During Operation

• This appliance has been designed for

non professional purpose in private

houses only. It is meant to cook edible

foodstuff only and must not be used

for any other purposes.

• It is dangerous to alter the specification

in any way.

• For hygiene and safety reasons, this

appliance should be kept clean at all

times. A build-up of fats or other

foodstuff could result in a fire.

• Under no circumstances should you

attempt to repair the appliance

yourself. Repairs carried out by

unexperienced persons may cause

injury or serious malfunctioning. Refer

to your local Service Centre. Always

insist on genuine spare parts.

• Ensure that all control knobs are in the

OFF position when not in use.

• Should you connect any electrical tool

to a plug near this cooking appliance,

ensure that electric cables are not in

English

This warnings has been given for the safety of you and others. We therefore

ask you to carefully read the procedures of installing and using this appliance.

Important safety information

contact with it and keep them far

enough from the heated parts of this

appliance.

• If the appliance is out of order,

disconnect it from the electric supply.

People Safety

• This appliance has been designed to

be operated by adults and children

under supervision. Young children

must not be allowed to tamper with the

controls or play near or with the oven.

• This appliance is not intended for use

by children or other persons whose

physical, sensory or mental capabilities

or lack of experience and knowledge

prevents them from using the

appliance safely without supervision or

instruction by a responsible person to

ensure that they can use the appliance

safely.

• Accessible parts of this appliance may

become hot when it is in use. Children

should be kept away until it has

cooled.

About Installation, Cleaning and

Manteinance

" It is mandatory that all operations

required for the installation are carried

out by a qualified or competent

person, in accordance with existing

rules and regulations.

• Disconnect the appliance from the

electrical supply, before carrying out

any cleaning or manteinance work.

• Ensure a good ventilation around the

6

appliance. A poor air supply could

cause lack of oxygen.

• Ensure that the gas supply complies

with the gas type stated on the

identification label, placed near the gas

supply pipe.

• This appliance is not connected to a

combustion products evacuation

device. It must be installed and

connected in accordance with current

installation regulations. Particular

attention shall be given to the relevant

requirements regarding ventilation.

• The use of a gas cooking

appliance results in the production

of heat and moisture in the room in

which it is installed. Ensure that

the kitchen is well ventilated: keep

natural ventilation holes open or

install a mechanical ventilation

device (mechanical extractor

hood).

• Prolonged intensive use of the

appliance may call for additional

ventilation, for example opening of

a window, or more effective

ventilation, for example increasing

the level of mechanical ventilation

where present.

• Once you removed all packaging from

the appliance, ensure that it is not

damaged and the electric cable is in

perfect conditions. Otherwise, contact

your dealer before proceeding with the

installation.

• The manufacturer disclaims any

responsability should all the safety

measures not be carried out.

Service

• Under no circumstances should you

attempt to repair the appliance

yourself. Repairs carried out by

unexperienced persons may cause

injury or serious malfunctioning. Refer

to your local Service Centre. Always

insist on genuine spare parts.

Environmental Information

" After installation, please dispose of

the packaging with due regard to

safety and the environment.

• When disposing of an old appliance,

make it unusable, by cutting off the

cable.

The symbol on the product or

on its packaging indicates that this

product may not be treated as household

waste. Instead it shall be handed over to

the applicable collection point for the

recycling of electrical and electronic

equipment. By ensuring this product is

disposed of correctly, you will help

prevent potential negative consequences

for the environment and human health,

which could otherwise be caused by

inappropriate waste handling of this

product. For more detailed information

about recycling of this product, please

contact your local city office, your

household waste disposal service or the

shop where you purchased the product.

It is very important that this

instruction book should be kept

safely for future consultation. If the

appliance should be sold or given to

another person, please ensure that

the booklet goes together with it, so

that the new owner can know of the

functions of the machine and also be

aware of the warnings.

These instructions are only for the

countries stated by the symbol printed

on the front cover of this instruction

book.

7

Operation

Hob burner control knobs

The symbols on the knobs mean:

" = no gas supply

= maximum gas supply

= minimum gas supply

For easier lighting, proceed before

putting a pan on the pan support.

Lighting the burners

Mod. ZGF 648 IX

Push the relevant knob down and

turn it anti-clockwise until it reaches

the "maximum" position.

Mod. ZGF 648 IR / ZGF 643 ITXC

After lighting the flame, keep the

knob pushed down for about 5

seconds. This will allow the

"thermocouple" (see figure - lett. D) to

be heated and the safety device to be

switched off, otherwise the gas supply

would be interrupted.

Then, check the flame is regular and

adjust it as required.

If you cannot light the flame even after

several attempts, check the "cap" and

“crown” (see figure - lett. A, B) are in the

correct position.

When switching on the mains, after

installation or a power cut, it is quite

normal for the spark generator to be

activated automatically.

In the absence of electricity, igni-

tion can occur without the

electrical device; in this case

approach the burner with a flame,

push the relevant knob down and

turn it anti-clockwise until it

reaches the "maximum" position.

!

A - Burner cap

B - Burner crown

C - Ignition candle

D - Thermocouple

8

Using the hob correctly

Practical hints

The burners

To ensure maximum burner

efficiency, you should only use pots and

pans with a flat bottom fitting the size of

the burner used.

Rapid Burner diameter 16-26 cm

Semi-rapid Burner diameter 12-22 cm

Auxiliary Burner diameter 8-16 cm

• For easier lighting, proceed before

putting a pan on the pan support.

• Use only pans or pots with flat bottom.

!

Do not keep the control knob

pressed for more than 15 se-

conds.

If the burner does not light

even after 15 seconds, release

the control knob, turn it the

"off" position and wait for at

least one minute before trying

to light the burner again.

To switch off burners

To put the flame out, turn the knob to

the symbol (").

The Hob Lid (available only for

model ZGF 648 IX)

In order to make the appliance match

with the kitchen design, a lid (not provided)

can be fitted on the hob.

• The lid is meant to avoid dust to

settle on the hob, when it is closed,

and to collect splashes of oil or

fat, when it is open. Do not use it

for any other purpose.

• Always wipe off any splash of

liquid before opening the lid.

• Always clean the lid from cooking

residues before opening it or

taking it off.

WARNING! The

crystal lid can

splinter when

overheated.

Always ensure all

the burners are off

before closing it.

9

Cleaning and Mainteinance

Disconnect the appliance from

the electrical supply, before

carrying out any cleaning or

manteinance work.

The hob is best cleaned whilst

it is still warm, as spillage can

be removed more easily than if

it is left to cool.

This appliance cannot be

cleaned with steam or with a

steam cleaning machine.

The burners

" The burner caps and crowns can be

removed for cleaning.

" Wash the burners taps and crowns

using hot soapy water, and remove

marks with a mild paste cleaner. A

well moistened soap impregnated

steel wool pad can be used with

caution, if the marks are particularly

difficult to remove.

• Take care when frying food in hot

oil or fat, as the overheated

splashes could easily ignite.

• If you use a saucepan which is smaller

than the recommended size, the flame

will spread beyond the bottom of the

vessel, causing the handle to overheat.

• Prolonged cooking with

potstones, earthenware pans or

cast-iron plates is inadvisable.

Also, do not use aluminium foil to

protect the top during use.

• Make sure pots do not protrude over

the edges of the cooktop and that they

are centrally positioned on the rings in

order to obtain lower gas

consumption.

• Do not place unstable or deformed

pots on the rings: they could tip over or

spill their contents, causing accidents.

" After cleaning, be sure to wipe dry

with a soft cloth.

" Frequently wash the "caps" and the

"crowns" with hot soapy water,

carefully taking away any built-up of

food.

The Hob Top

" Regularly wipe over the hob top

using a soft cloth well wrung out in

warm water to which a little wasing

up liquid has been added. Avoid the

use of the following:

- household detergent and bleaches;

- impregnated pads unsuitable for

non-stick saucepans;

- steel wool pads;

- bath/sink stain removers.

" Should the hob top become heavily

soiled, the following products are

recommended:

- For stainless steel hobs use a

• Pots must not enter the control zone.

• If the control knobs become difficult to

turn, please contact your local Service

Force Centre.

• As soon as a liquid starts boiling, turn

down the flame so that it will barely

keep the liquid simmering.

10

proprietary stainless steel cleaner.

- For other hobs use Hob Brite or Bar

Keepers Friend.

" Do not leave acid or alkaline

substances (e.g. vinegar, salt,

lemon juice, etc.) on the cooktop.

Pan supports

To keep the pan supports in the right

position, they are hooked to a couple of

special hinges in the back of the hob.

Thanks to these hooks, you can lift the pan

supports for easier cleaning, as shown in

the picture.

To take the pan supports completely off the

hob, proceed as shown in the picture.

The Ignition electrode

The electric ignition is obtained

through a ceramic electrode with a

metal electrode. Keep these

components very clean, to avoid difficult

lighting, and check that the burner

crown holes are not obstructed.

Cast iron pan supports

(ZGF

643 ITXC / ZGF 648 IR)

Caution!

When removing the cast iron pan

supports, lift them up. Never turn

the pan supports on the hinges

since this could damage them.

Periodic Maintenance

Periodically ask your local Service Centre

to check the conditions of the gas supply

pipe and the pressure adjuster, if fitted.

NO

YES

11

Technical data

Burner gas power (natural gas G20-20 mbar)

Rapid burner 3,0 kW

Semi-rapid burner 2,0 kW

Auxiliary burner 1,0 kW

Category II2H3B/P

Gas supply natural gas G20 (2H) / 20 mbar

Gas connection G 1/2"

Electric supply 230 V~ 50 Hz

Appliance class 3

Hob dimensions

Width 580 mm

Depth 510 mm

Cut out dimensions

Width 560 mm

Depth 480 mm

By-pass diameters

Burner Ø By-pass in 1/100 mm.

Auxiliary 28

Semi-rapid 32

Rapid 42

12

Gas burners

NORMAL REDUCED

NORMAL

POWER POWER

POWER

BURNER NATURAL GAS LPG

G20 (2H) - 20 mbar

(Butane/Propane) 30 mbar

kW kW g/h

inj. m

3

/h inj.

G30 G31

100/mm 100/mm

Auxiliary

burner 1,0 0,33 70 0,095 50 73 71

Semi-rapid

burner 2,0 0,45 96 0,190 71 145 143

Rapid 3,0

burner (natural gas) 0,75 119 0,285 86 204 200

2,8

(

LPG

)

Gas burners G20 13 mbar - only for Russia

NORMAL REDUCED

NORMAL

POWER POWER

POWER

BURNER

NATURAL GAS

G20 - 13 mbar

kW kW inj. m

3

/h

100/mm

Auxiliary

burner 0,9 0,33 80 0,095

Semi-rapid

burner 1,4 0,45 105 0,148

Rapid

burner 1,9 0,75 120 0,20

13

l The following instructions about

installation and maintenance must

be carried out by qualified

personnel in compliance with the

regulation in force.

l The appliance must be electrically

disconnected before all

interventions. If any electric supply

to the appliance is required to

carry out the work, ensure all the

necessary precautions are

followed.

l The side walls of the unit in which

the hob is going to be installed,

must not exceed the height of the

working top.

l Avoid installing the appliance in

the proximity of inflammable

materials (e.g. curtains, tea towels

etc.).

THE MANUFACTURER WILL NOT

ACCEPT LIABILITY, SHOULD ANY

OF THE OTHER SAFETY

INSTRUCTIONS INCORPORATED IN

THIS BOOKLET OR THE

REGULATION IN FORCE BE

IGNORED.

Installation

Choose fixed connections or use a

flexible pipe in stainless steel in

compliance with the regulation in force.

If using flexible metallic pipes, be careful

they do not come in contact with mobi-

le parts or they are not squeezed. Use

the same attention when the hob is

combinated with an oven.

Gas connection

14

IMPORTANT - To ensure a correct

operation, a savingof energy and the

long life of the appliance, the voltage

pressure of the appliance must

correspond to the recommended values.

The adjustable connection is fixed to the

comprehensive ramp by means of a

threaded nut G 1/2". Interpose the

sealing between the components as

shown in the picture. Screw the parts

without forcing, adjust the connection in

the required direction and tighten

everything.

IMPORTANT

Once installation is complete,

check the perfectseal of every

pipe fitting, using a soapy

solution, never a flame.

A) Ramp with ending nut

B) Seal

C) Adjustable connection

15

Adaptation to different types of gas

A. Injectors replacement

• Remove the pan supports.

• Remove the burner's caps and

crowns.

• With a socket spanner 7 unscrew

and remove the injectors (Fig. 1), and

replace them with the ones required

for the type of gas in use (see table

2).

• Reassemble the parts, following the

same procedure backwards.

• Replace the rating label (placed near

the gas supply pipe) with the relevant

one for the new type of gas supply.

You can find this label in the package

of the injectors supplied with the

appliance.

Should the feeding gas pressure be

different or variable compared with the

required pressure, an appropriate

pressure adjuster must be fitted on the

gas supply pipe, in compliance with the

rules in force.

B. Adjustment of minimum

level

To adjust the minimum level of the

burners, proceed as follows:

• Light the burner.

• Turn the knob on the minimum

position.

• Remove the knob.

• With a thin screwdriver, adjust the

by-pass screw positioned in the

centre of the gas tap control shaft

(see Fig. 2). If changing from natural

gas 20/13 mbar to liquid gas,

completely tighten the adjustment

screw in. If changing from liquid gas

to natural gas 20 mbar, undo the by-

pass screw about 1/4 of a turn. If

changing from natural gas 20 mbar

to natural gas 13 mbar undo the by-

pass screw about 1/4 of a turn. If

changing from liquid gas to natural

!!

!

!!

!

gas 13 mbar, undo the by-pass

screw about 3/4 of a turn.

• Finally check the flame does not go

out when quickly turning the knob

from the maximum position to the

minimum position.

This procedure can easily be carried

out, anyhow the hob has been

positioned or built in the working top.

Minimum adjustment screw

Fig. 1

Fig. 2

16

The appliance is designed to be

connected to 230 V monophase

electricity supply.

The connection must be carried out

in compliance with the laws and

regulations in force.

Before the appliance is connected:

1) check that the main fuse and the

domestic installation can support the

load (see the rating label);

2) check that the power supply is

properly earthed in compliance with the

current rules;

3) check the socket or the double

pole switch used for the electrical

connection can be easily reached with

the appliance built in the forniture unit.

The appliance is supplied with a

connection cable. This has to be

provided with a proper plug, able to

support the load marked on the

identification plate. To connect the plug

to the cable, follow the recommendation

given in Fig. 3-a. The plug has to be

fitted in a proper socket.

If connecting the appliance directly

to the electric system, it is necessary

that you install a double pole switch

between the appliance and the

electricity supply, with a minimum gap

of 3 mm. between the switch contacts

and of a type suitable for the required

load in compliance with the current

rules.

The connection cable has to be

placed in order that, in each part, it

cannot reach a temperature 50°C

higher than room temperature.

The brown coloured phase cable

(fitted in the terminal block contact

marked with "L") must always be

connected to the network phase.

Electrical connection

Remplacement of the voltage

cable

The connection of the voltage cable

to the appliance's terminal block is of

type "Y". This means that its

replacement requires the specific

equipment of a technician. In this case,

only cable type H05V2V2-F T90 must

be used. The cable section must be

suitable to the voltage and the working

temperature. The yellow/green earth

wire must be approximately 2 cm.

longer than the phase wires (Fig. 3-a).

To open the terminal block and

reach the terminals, proceed as follows:

• insert the point of a screwdriver

into the visible protrunding part of the

terminal block;

• exert a light pressure and lift (Fig.

3-b).

Earth

(yellow/green))

Neutral

Fig. 3-a

Fig. 3-b

17

Building in

This hob can be inserted in a built-in

kitchen unit whose depth is between

550 and 600 mm. The hobs dimensions

are shown in Fig. 4.

The edge of the cut out must have a

minimum distance from the rear wall of

55 mm.

If there are side walls, or sides of the

furniture unit near the hob, the cut out

edges must have a minimum distance of

100 mm.

Hanging forniture units or hoods

must be placed at 650 mm. minimum

from the hob.

A = Auxiliary burner

SR= Semi-rapid burner

R = Rapid burner

SR

R

A

510

580

Fig. 4

Fitting the lid

We recommend the lid hinge blockWe recommend the lid hinge block

We recommend the lid hinge block

are fitted before installing the hobare fitted before installing the hob

are fitted before installing the hob

into the worktop.into the worktop.

into the worktop.

To install the lid onto the hob, proceed

as follows:

a.a.

a. Remove the right and left hand grid

blocks fitted to the back of the hob, by

unscrewing the relevant screws (Fig.

5).

Fig. 5

SR

R

A

510

580

18

b.b.

b. Fit the lid hinge blocks onto the hob,

using the original screws, ensuring

that the relevant shims are fitted

between the hinge blocks and the

hob;

c.c.

c. Fit the left hand lid hinge (marked S)

into the hinge block (Fig. 6);

d.d.

d. Carry out the same operation with the

right hand lid hinge (marked D)

..

.

Adjusting the lid balance

To adjust the lid balance, turn clockwise

or anti-clockwise the central screw of

the right- and left-hand hinges (Fig. 7).

Fig. 6

Fig. 7

19

Fitting the hob to the worktop

The hob can be installed in a kitchen

unit with an opening for insertion whose

dimensions are shown in Fig. 8. To

install the hob, proceed as follows:

1. Remove the pan supports, the

burners caps and crowns and turn

the hob upside down, taking care

the ignition candles are not

damaged in this operation.

2. put the relevant sealings, supplied

with the hob, on the edges of the cut

out, as shown in Fig. 9, taking care

that the sealings meet without

overlapping;

3. place the hob in the cut out, taking

care of its centring;

4. fix the hob with the relevant screws

(Fig. 10). The traction of the screws is

able to trace the sealing, any excess

of which can then be easily removed.

The edge of the hob forms a double

labyrinth seal which provides a total

guarantee against infiltration of liquids.

Fig. 10

Fig. 9

sealing

gasket

Dimensions are given in millimeters

Fig. 8

20

Possibilities for insertion

Kitchen unit with door

Proper arrangements must be taken

in designing the forniture unit, in order to

avoid any contact with the bottom of the

hob which can be heated when it is

operated. The recommended solution is

shown in Fig. 11. The panel fitted under

the hob should be easily removable to

allow an easy access if a technical assis-

tance intervention is needed.

Kitchen unit with oven

The hob recess dimensions must

comply the indication given in Figs. 12

and 13 and must be provided with

brackets to allow a continuous supply of

air.

The hob's electric connection and

the oven's one must be carried out

separately, both for safety reasons and

to allow the oven to be easily taken off

the unit.

a) Removable panel

b) Space for connections

Fig. 12

Fig. 13

Fig. 11

Страница загружается ...

Zanussi ZGF648IX Руководство пользователя

Это руководство также подходит для

Zanussi ZGF648IX Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов