Makita EM4350LH Original Instruction Manual

Original Instruction Manual

Originalbruksanvisning

Original bruksanvisning

Alkuperäinen käyttöohje

Oriģinālā instrukciju rokasgrāmata

Originali naudojimo instrukcija

Algne kasutusjuhend

Оригинальное руководство по эксплуатации

Important:

Read this instruction manual carefully before putting the Petrol Brushcutter into operation and strictly observe the safety regulations!

Preserve instruction manual carefully!

Viktigt:

Läs igenom bruksanvisningen noga innan du använder den bensindrivna röjsågen och följ säkerhetsanvisningarna noggrant!

Förvara bruksanvisningen för framtida bruk!

Viktig:

Les denne bruksanvisningen nøye før du tar den bensindrevne skogsrydderen i bruk. Følg sikkerhetsanvisningene nøye!

Ta godt vare på bruksanvisningen!

Tärkeää:

Lue tämä käyttöohje huolellisesti, ennen kuin otat bensiinikäyttöisen pensasleikkurin käyttöön, ja noudata tarkoin turvamääräyksiä.

Säilytä käyttöohje huolellisesti.

Svarīgi:

Pirms benzīna krūmgrieža ekspluatācijas rūpīgi izlasiet šo lietošanas rokasgrāmatu un pilnībā ievērojiet drošības noteikumus!

Lietošanas rokasgrāmatu rūpīgi glabājiet!

Svarbu:

Prieš pradėdami naudoti benzininę krūmapjovę, atidžiai perskaitykite visą naudojimo instrukciją ir griežtai laikykitės saugos taisyklių!

Išsaugokite naudojimo instrukciją, kad galėtumėte ja pasinaudoti ateityje!

Tähtis:

Enne bensiinimootoriga võsalõikuri kasutamist lugege hoolikalt käesolevat kasutusjuhendit ja järgige täpselt kõiki ohutuseeskirju!

Hoidke kasutusjuhend alles!

Важно:

Внимательно ознакомьтесь с данным руководством, прежде чем приступать к эксплуатации бензокосы, и строго соблюдайте

правила техники безопасности!

Бережно храните данное руководство!

EM4351UH EM4350UH EM4350LH

2

Thank you very much for purchasing the MAKITA Outdoor Power Equipment.

We are pleased to recommend to you the MAKITA product which is the result of

a long development program and many years of knowledge and experience.

Please read this booklet which refers in detail to the various points that will

demonstrate its outstanding performance. This will assist you to obtain the best

possible result from your MAKITA product.

Table of Contents Page

You will note the following symbols when reading the instructions manual.

SYMBOLS

English

(Original instructions)

Symbols .........................................................................2

Safety instructions .........................................................3

Technical data................................................................7

Designation of parts.......................................................8

Mounting of handle ........................................................9

Mounting of protector...................................................10

Mounting of metal blade or nylon cutting head ............12

Before start of operation ..............................................13

Correct handling of machine........................................15

Points in operation and how to stop ............................16

Resharpening the cutting tool ......................................19

Servicing instructions...................................................22

Storage ........................................................................25

Read instruction manual and follow the

warnings and safety precautions!

Take Particular care and attention!

Forbidden!

Keep distance!

Flying object hazard!

Kickback!

No smoking!

No open ame!

Protective gloves must be worn!

Wear sturdy boots with nonslip soles.

Steeltoed safety boots are recommended!

Keep the area of operation clear of all

persons and pets!

Wear protective helmet, eye and ear

protection!

Top permissible tool speed

Fuel (Gasoline)

Engine-manual start

Emergency stop

First Aid

ON/START

OFF/STOP

THROTTLE LOCK POSITION

3

15 Meters

Diagrammatic gure

SAFETY INSTRUCTIONS

General Instructions

Read this instruction manual to become familiar with handling of the –

equipment. Users insufciently informed will risk danger to themselves as

well as others due to improper handling.

It is recommended only to lend the equipment to people who have proven to –

be experienced.

Always hand over the instruction manual.

First users should ask the dealer for basic instructions to familiarize oneself –

with the handling of brushcutters.

Children and young persons aged under 18 years must not be allowed to –

operate this equipment. Persons over the age of 16 years may however

use the device for the purpose of being trained while under supervision of a

qualied trainer.

Use with the utmost care and attention. –

Operate only if you are in good physical condition. Perform all work calmly –

and carefully. The user has to accept liability for others.

Never use this equipment after consumption of alcohol or drugs, or if feeling –

tired or ill.

National regulation can restrict the use of the machine. –

Intended use of the machine

This equipment is only intended for cutting grass, weeds, bushes, –

undergrowth. It should not be used for any other purpose such as edging or

hedge cutting as this may cause injury.

Personal protective equipment

The clothing worn should be functional and appropriate, i.e. it should be tight- –

tting but not cause hindrance. Do not wear either jewelry or clothing which

could become entangled with bushes or shrubs.

In order to avoid either head-, eye-, hand-or foot injuries as well as to protect –

your hearing the following protective equipment and protective clothing must

be used during operation.

Always wear a helmet where there is a risk of falling objects. The protective –

helmet (1) is to be checked at regular intervals for damage and is to be

replaced at the latest after 5 years. Use only approved protective helmets.

The visor (2) of the helmet (or alternatively goggles) protects the face from –

ying debris and stones. During operation always wear goggles, or a visor to

prevent eye injuries.

Wear adequate noise protection equipment to avoid hearing impairment (ear –

muffs (3), ear plugs etc.).

The work overalls (4) protect against ying stones and debris. –

We strongly recommend that the user wears work overalls.

Gloves (5) are part of the prescribed equipment and must always be worn –

during operation.

When using the equipment, always wear sturdy shoes (6) with a non-slip –

sole. This protects against injuries and ensures a good footing.

Starting up the brushcutter

Please make sure that there are no children or other people within a working –

range of 15 meters (50 ft), also pay attention to any animals in the working

vicinity.

Before use always check the equipment is safe for operation: –

Check the security of the cutting tool, the throttle lever for easy action and

check for proper functioning of the throttle lever lock.

Rotation of the cutting tool during idling speed is not allowed. Check with your –

dealer for adjustment if in doubt. Check for clean and dry handles and test

the function of the start/stop switch.

4

Resting•

Transport•

Refueling•

Maintenance•

Tool replacement•

3 meters

Start the brushcutter only in accordance with the instructions.

Do not use any other methods for starting the engine! –

Use the brushcutter and the tools only for such applications as specied. –

Only start the engine, after the entire assembly is done. Operation of the –

device is only permitted after all the appropriate accessories are attached!

Before starting make sure that the cutting tool has no contact with hard –

objects such as branches, stones etc. as the cutting tool will revolve when

starting.

The engine is to be switched off immediately in case of any engine problems. –

Should the cutting tool hit stones or other hard objects, immediately switch off –

the engine and inspect the cutting tool.

Inspect the cutting tool at short regular intervals for damage (detection of –

hairline cracks by means of tapping-noise test).

If the equipment gets heavy impact or fall, check the condition before –

continuing work. Check the fuel system for fuel leakage and the controls

and safety devices for malfunction. If there is any damage or doubt, ask our

authorized service center for the inspection and repair.

Operate the equipment only with the shoulder harness attached which is –

to be suitably adjusted before putting the brushcutter into operation. It is

essential to adjust the shoulder harness according to the user size to prevent

fatigue occurring during use. Never hold the cutter with one hand during use.

During operation always hold the brushcutter with both hands. –

Always ensure a safe footing.

Operate the equipment in such a manner as to avoid inhalation of the exhaust –

gases. Never run the engine in enclosed rooms (risk of gas poisoning).

Carbon monoxide is an odorless gas.

Switch off the engine when resting and when leaving the equipment –

unattended, and place it in a safe location to prevent danger to others or

damage to the machine.

Never put the hot brushcutter onto dry grass or onto any combustible –

materials.

Always install the approved cutting tool guard onto the equipment before –

starting the engine.

Otherwise contact with the cutting tool may cause serious injury.

All protective installations and guards supplied with the machine must be –

used during operation.

Never operate the engine with faulty exhaust mufer. –

Shut off the engine during transport. –

When transporting the equipment, always attach the cover to the metal blade. –

Ensure safe position of the equipment during car transportation to avoid fuel –

leakage.

When transporting, ensure that the fuel tank is completely empty. –

When unloading the equipment from the truck, never drop the Engine to the –

ground or this may severely damage the fuel tank.

Except in case of emergency, never drop or cast the equipment to the ground –

or this may severely damage the equipment.

Remember to lift the entire equipment from the ground when moving the –

equipment. Dragging the fuel tank is highly dangerous and will cause damage

and leakage of fuel, possibly causing re.

Refueling

Shut off the engine during refueling, keep away from open ames and do not –

smoke.

Avoid skin contact with mineral oil products. Do not inhale fuel vapor. Always –

wear protective gloves during refueling. Change and clean protective clothing

at regular intervals.

Take care not to spill either fuel or oil in order to prevent soil contamination –

(environmental protection). Clean the brushcutter immediately after fuel has

been spilt.

Avoid any fuel contact with your clothing. Change your clothing instantly if –

fuel has been spilt on it (to prevent clothing catching re).

Inspect the fuel cap at regular intervals making sure that it can be securely –

fastened and does not leak.

Carefully tighten the fuel tank cap. Change location to start the engine (at –

least 3 meters away from the place of refueling).

Never refuel in closed rooms. Fuel vapors accumulate at ground lever (risk of –

explosions).

Only transport and store fuel in approved containers. Make sure the fuel –

stored is not accessible to children.

5

Caution:

Kickback

Diagrammatic

gure

Diagrammatic

gure

Method of operation

Only use in good light and visibility. During the winter season beware of –

slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe

footing.

Never cut above waist height. –

Never stand on a ladder. –

Never climb up into trees to perform cutting operation. –

Never work on unstable surfaces. –

Remove sand, stones, nails etc. found within the working range. –

Foreign particles may damage the cutting tool and can cause dangerous

kick-backs.

Before commencing cutting, the cutting tool must have reached full working –

speed.

When using metal blades, swing the tool evenly in half-circle from right to left, –

like using a scythe.

If grass or branches get caught between the cutting tool and guard, always

stop the engine before cleaning. Otherwise unintentional blade rotation may

cause serious injury.

Take a rest to prevent loss of control caused by fatigue. We recommend to –

take a 10 to 20-minute rest every hour.

Cutting Tools

Use an applicable cutting tool for the job in hand. –

Nylon cutting heads (string trimmer heads) are suitable for trimming lawn

grass.

Metal blades are suitable for cutting weeds, high grasses, bushes, shrubs,

underwood, thicket, and the like.

Never use other blades including metal multi-piece pivoting chains and ail

blades. Otherwise serious injury may result.

When using metal blades, avoid “kickback” and always prepare for an –

accidental kickback. See the section “Kickback” and “Kickback prevention.”

Kickback (blade thrust)

Kickback (blade thrust) is a sudden reaction to a caught or bound metal –

blade. Once it occurs, the equipment is thrown sideway or toward the

operator at great force and it may cause serious injury.

Kickback occurs particularly when applying the blade segment between 12 –

and 2 o’clock to solids, bushes and trees with 3 cm or larger diameter.

To avoid kickback: –

Apply the segment between 8 and 11 o’clock;•

Never apply the segment between 12 and 2 o’clock;•

Never apply the segment between 11 and 12 o’clock and between 2 and •

5 o’clock, unless the operator is well trained and experienced and does it at

his/her own risk;

Never use metal blades close to solids, such as fences, walls, tree trunks •

and stones;

Never use metal blades vertically, for such operations as edging and •

trimming hedges.

Vibration

People with poor circulation who are exposed to excessive vibration may –

experience injury to blood vessels or the nervous system. Vibration may

cause the following symptoms to occur in the ngers, hands or wrists: “Falling

asleep” (numbness), tingling, pain, stabbing sensation, alteration of skin color

or of the skin. If any of these symptoms occur, see a physician!

To reduce the risk of “white nger disease”, keep your hands warm during –

operation and well maintain the equipment and accessories.

Maintenance instructions

Have your equipment serviced by our authorized service center, always using –

only genuine replacement parts. Incorrect repair and poor maintenance can

shorten the life of the equipment and increase the risk of accidents.

The condition of the cutter, in particular of the cutting tool of the protective –

devices and also of the shoulder harness must be checked before

commencing work. Particular attention is to be paid to the metal blades which

must be correctly sharpened.

Turn off the engine and remove spark plug connector when replacing or –

sharpening cutting tools, and also when cleaning the cutter or cutting tool.

6

For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s):

Designation of Machine: Petrol Brushcutter

Model No./ Type: EM4351UH, EM4350UH, EM4350LH

Specications: see “TECHNICAL DATA” table

are of series production and

Conforms to the following European Directives:

2000/14/EC, 2006/42/EC

And are manufactured in accordance with the following standards or standardized documents:

EN ISO 11806-1

The technical documentation is kept by our authorized representative in Europe who is:

Makita International Europe Ltd.,

Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, England

The conformity assessment procedure required by Directive 2000/14/EC was in Accordance with annex V.

EM4351UH:

Measured Sound Power Level: 111.9 dB

Guaranteed Sound Power Level: 113 dB

EM4350UH:

Measured Sound Power Level: 112.1 dB

Guaranteed Sound Power Level: 113 dB

EM4350LH:

Measured Sound Power Level: 110.7 dB

Guaranteed Sound Power Level: 112 dB

8. 9. 2011

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

Never straighten or weld damaged cutting tools.

Pay attention to the environment. Avoid unnecessary throttle operation for –

less pollution and noise emissions. Adjust the carburetor correctly.

Clean the equipment at regular intervals and check that all screws and nuts –

are well tightened.

Never service or store the equipment in the vicinity of naked ames. –

Always store the equipment in locked rooms and with an emptied fuel tank. –

When cleaning, servicing and storing the equipment, always attach the cover –

to the metal blade.

Observe the relevant accident prevention instructions issued by the relevant trade associations and by the insurance companies.

Do not perform any modications to the equipment as this will endanger your safety.

The performance of maintenance or repair work by the user is limited to those activities as described in the instruction manual. All other work is

to be done by an Authorized Service Agent. Use only genuine spare parts and accessories released and supplied by MAKITA.

Use of non-approved accessories and tools means increased risk of accidents.

MAKITA will not accept any liability for accidents or damage caused by the use of non-approved cutting tools and xing devices of cutting tools,

or accessories.

First Aid

In case of accident make sure that a rst-aid box is available in the vicinity of

the cutting operations. Immediately replace any item taken from the rst aid box.

When asking for help, please give the following

information:

Place of accident –

What happened –

Number of injured persons –

Kind of injuries –

Your name –

7

TECHNICAL DATA EM4351UH, EM4350UH, EM4350LH

Model EM4351UH EM4350UH EM4350LH

Handle type Bike handle Bike handle Loop handle

Dimensions: length x width x height (without cutting tool) mm 1,812 x 618 x 528 1,812 x 635 x 460 1,812 x 339 x 250

Mass (without plastic guard and cutting tool) kg 8.6 8.3 7.9

Volume (fuel tank) L 0.6

Volume (oil tank) L 0.1

Engine displacement cm

3

43.0

Maximum engine performance kW 1.5 at 7,500 min

-1

Engine speed at recommended max. spindle speed min

-1

10,500

Maximum spindle speed (corresponding) min

-1

7,200

Idling speed min

-1

3,000

Clutch engagement speed min

-1

4,000

Carburetor Diaphragm type

Ignition system Non-contact, magnet type

Spark plug type NGK CMR6A

Electrode gap mm 0.7 - 0.8

CUTTER

BLADE

NYLON

CUTTING

HEAD

CUTTER

BLADE

NYLON

CUTTING

HEAD

CUTTER

BLADE

NYLON

CUTTING

HEAD

Vibration per

ISO 22867

Right handle

(Rear grip)

a

hv eq

m/s

2

2.2 2.1 3.1 3.5 4.2 2.6

Uncertainty K m/s

2

0.5 0.6 0.5 0.8 1.1 0.7

Left handle

(Front grip)

a

hv eq

m/s

2

1.7 2.0 4.8 4.0 3.8 3.7

Uncertainty K m/s

2

0.5 0.5 2.9 0.9 1.0 1.4

Sound pressure level average to

ISO 22868

L

PA eq

dBA 92.4 96.2 91.2 96.1 92.8 94.9

Uncertainty K dBA 1.8 2.0 2.2 1.6 1.6 2.1

Sound power level average to

ISO 22868

L

WA eq

dBA 101.8 108.9 103.1 109.1 103.4 107.7

Uncertainty K dBA 1.8 1.4 1.1 1.1 1.5 1.2

Fuel Automobile gasoline (petrol)

Engine Oil

API grade SF class or higher, SAE 10W-30 oil

(automobile 4-stroke engine oil)

Cutting tools (cutter blade dia.) mm 305 (with three blades)

Gear ratio 13/19

8

EM4350LHEM4351UH EM4350UH

DESIGNATION OF PARTS

7

12

8

9

11

4

10

13

15

14

4

11

12

9

10

16

13

14

15

4

11

12

7

10

16

13

14

15

9

5

6

19

20

2

1

17

18

3

GB DESIGNATION OF PARTS

1 Fuel tank

2 Recoil starter

3 Air cleaner

4

I-O and throttle lock switch

(on/off)

5 Spark plug

6 Exhaust mufer

7 Clutch case

8 Rear grip

9 Hanger

10 Handle

11 Throttle lever

12 Control cable

13 Shaft

14 Protector (Cutting tool guard)

15 Gear Case/Head case

16 Handle holder

17 Fuel tank cap

18 Starter knob

19 Exhaust pipe

20 Oil cap

9

CAUTION: Before doing any work on the equipment, always stop the engine

and pull the spark plug connector off the spark plug.

Always wear protective gloves!

CAUTION: Start the engine only after having assembled it completely.

For model EM4351UH, EM4350UH

Insert the shaft of the handle into the grip as shown.

Align the screw hole in the grip with the one in the shaft.

Tighten the screw securely.

MOUNTING OF HANDLE

Loosen knob (1). –

Place handle (4) between handle clamp (2) and handle holder (3). –

Adjust handle (4) to an angle that provides a comfortable working position –

and then secure by rmly hand-tightening knob (1).

CAUTION: Do not forget to mount spring (5).

For model EM4350LH

Fix the loop handle on the shaft with four screws. –

To keep a proper distance between the grips, place the spacer (1) between –

the loop handle and the hanger (2).

(1)

(2)

(4)

(3)

(5)

(1)

(2)

Engine

Grip

Screw

Handle

10

To meet the applicable safety provisions, only the tool/protector

combinations as indicated in the table must be used.

MOUNTING OF PROTECTOR

Be sure to use genuine MAKITA metal blades (including

saw blade and cutter blade) or nylon cutting head.

The metal blade must be well polished, free of cracks or –

breakage. If the metal blade hits against a stone during

operation, stop the engine and check the blade immediately.

Polish or replace the metal blade every three hours of –

operation.

If the nylon cutting head hits against a stone during –

operation, stop the engine and check the nylon cutting head

immediately.

CAUTION: The appropriate protector must always be installed,

for your own safety and in order to comply with

accident prevention regulations.

Operation of the equipment without the guard being

in place is not permitted.

The outside diameter of the cutter blade must be

300 mm (12”) or smaller. Never use any blades

exceeding 300 mm (12”) in outside diameter.

Use 200 mm saw-blade protector only when using

200 mm saw-blade.

Use 225 mm saw-blade protector only when using

225 mm saw-blade.

Do not apply other combination when using saw-

blade.

NOTE: The standard combination of cutting tool differs from

county to country.

Cutter blade

200 mm saw blade

225 mm saw blade

Nylon cutting head

Protector for metal blades

Protector for

200 mm saw blade

Protector for 225 mm

saw blade

Protector for

nylon cutting head

11

(3)

(4)

In cases where the nylon cord cutter is to be used, be sure to mount the –

nylon cord cutter protector (4) onto the metal blade protector (3).

Mount the nylon cord cutter protector (4) by sliding it into place from the ank –

of the metal blade protector (3) as shown.

Remove tape adhered to cutter, which cuts nylon cord, on nylon cord cutter –

protector (4).

CAUTION: Be sure to push in nylon cord cutter protector (4) until it is fully

inserted.

Take care not to injure yourself on the cutter for cutting the nylon

cord.

To remove the nylon cord cutter protector (4), apply a hex wrench into the –

notch on the metal blade protector (3), push it in and meanwhile slide the

nylon cord cutter protector (4).

Hex wrench

(3)

(2)

(1)

(2)

(3)

In use of the metal blade, x the protector (3) to the clamp (2) with two bolts –

(1).

NOTE: Tighten the right and left bolts evenly so that the gap between the clamp

(2) and the protector (3) will be constant.

Otherwise, the protector sometimes may not function as specied.

12

Be sure to use genuine MAKITA metal blades or nylon

cutting head.

The metal blade must be well polished, free of cracks or breakage. If the –

metal blade hits against a stone during operation, stop the engine and check

the blade immediately.

Polish or replace the metal blade every three hours of operation. –

If the nylon cutting head hits against a stone during operation, stop the –

engine and check the nylon cutting head immediately.

CAUTION: The appropriate protector must always be installed, for your own

safety and in order to comply with accident-prevention regulations.

Operation of the equipment without the guard being in place is not

permitted.

The outside diameter of the cutter blade must be 300 mm (12”)

or less. Never use any blades exceeding 300 mm (12”) in outside

diameter.

Turn the machine upside down, and you can replace the metal blade or nylon

cutting head easily.

Insert the hex wrench through the hole in the gear case and rotate the –

receiver washer (4) until it is locked with the hex wrench.

Loosen the nut (1) (left-hand thread) with the socket wrench and remove the –

nut (1), cup (2), and clamp washer (3).

(4)

(3)

(2)

(1)

(4)

(3)

(2)

(1)

Rotation

Hex wrench

MOUNTING OF METAL BLADE OR NYLON CUTTING HEAD

Mounting of metal blade with the hex wrench still in place

Mount the metal blade onto the shaft so that the guide of the receiver washer –

(4) ts in the arbor hole in the metal blade. Install the clamp washer (3), cup

(2), and secure the metal blade with the nut (1).

[Tightening torque: 20 - 30 N-m]

NOTE: Always wear gloves when handling the metal blade.

NOTE: The metal blade-fastening nut (with spring washer) is a consumable

part. If there appears any wear or deformation on the spring washer,

replace the nut.

Mounting of nylon cutting head

The clamp washer (3), cup (2), and nut (1) are not necessary for mounting –

the nylon cutting head. The nylon cutting head should go on top of the

receiver washer (4).

Insert the hex wrench through the hole in the gear case and rotate the –

receiver washer (4) until it is locked with the hex wrench.

Then screw the nylon cutting head onto the shaft by turning it counter- –

clockwise.

Remove the hex wrench. –

Hex wrench

Loosen Tighten

Hex wrench

13

Inspection and rell of engine oil

Perform the following procedure, with the engine cooled down. –

Assure that the engine is on a at horizontal surface and conrm if the oil level is between the lower or upper limit of the oil indicator. –

If the oil level is below the lower limit, remove the oil cap and add oil. –

The area surrounding the external marks is transparent, so the amount of oil inside can be checked without having to remove the oil cap. –

However, if oil pipe becomes extremely dirty, visibility may be lost, and oil level will have to be checked against stepped section on inside of

oil pipe.

You may need to rell oil approximately every 10 operating hours (every 10 refuelings). –

If the oil changes in color or mixes with dirt, replace it with new one. (For the interval and method of replacement, refer to P 22.)

Recommended oil: SAE 10W-30 oil of API Classication, Class SF or higher (4-stroke engine for automobile)

Oil volume: Approx. 0.10L

NOTE: If the engine is not positioned as illustrated on a horizontal surface, an inaccurate indication of oil level may occur and oil may be

overlled. Filling oil above the upper limit may cause oil contamination and/or white smoke.

Replacement of oil: “Oil cap”

Remove dust or dirt near the oil rell port, and detach the oil cap. –

Keep the detached oil cap free of sand or dust. Otherwise, any sand or dust adhering to the oil cap may cause irregular oil circulation or –

wear on the engine parts, which will result in troubles.

BEFORE START OF OPERATION

(1) Keep the engine level, and detach the oil cap.

(2) Fill with oil to upper limit mark.

Use oil bottle when lling.

(3) Securely tighten the oil cap. Insufcient tightening may cause oil leakage.

Upper limit

Lower limit

Oil

14

Refueling

WARNING: Shut off the engine before refueling, keep away from

open ames and do not smoke.

Loosen the tank cap a little to release the tank pressure. –

Detach the tank cap, and refuel, discharging air by tilting the fuel tank so that –

the refuel port will be oriented upward. DO NOT ll fuel up to the top of the

tank.

Wipe the outside of the tank cap to prevent debris from entering into the fuel –

tank.

After refueling, securely tighten the tank cap. –

If there is any aw or damage on the tank cap, replace it.•

The tank cap wears out in course of time. Replace it every two to three years.•

DO NOT put fuel in the oil ll port.•

Fuel tank cap

Fuel upper limit

Fuel tank

Note

Do not replace oil with the engine in a tilted position.•

Filling with oil while engine is tilted leads to overlling which causes oil contamination and/or white smoke.•

After relling oil

Wipe with a rag any spilled oil immediately. –

REFUELING

Handling of fuel

It is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be performed in a sufciently

ventilated room or in the open air. Never inhale fuel vapor, and keep fuel away from you. If you touch fuel repeatedly or for a long time, the

skin becomes dry, which may cause skin disease or allergy. If fuel enters into the eye, clean the eye with fresh water. If your eye remains still

irritated, consult your doctor.

Storage period of fuel

Fuel should be used within a period of 4 weeks, even if it is kept in a special container in a well-ventilated and shaded area.

Otherwise, fuel may deteriorate in one day.

STORAGE OF MACHINE AND REFILL TANK

Keep the machine and tank at a cool place free from direct sunshine. –

Never keep the fuel in a car. –

Fuel

The engine is a four-stroke engine. Be sure to use an unleaded automobile gasoline 87 or higher octane ((R+M)/2). It may contain no more than

10% alcohol (E-10).

Points for fuel

Never use a gasoline mixture which contains engine oil. Otherwise, it will cause excessive carbon accumulation or mechanical troubles. –

Use of deteriorated oil will cause irregular start-up. –

15

CORRECT HANDLING OF MACHINE

Attachment of shoulder harness

Adjust the strap length so that the metal blade will be –

kept parallel with the ground.

For EM4351UH, EM4350UH

Hold the harness on your back, attach it with the buckle,

and adjust the length of the bands.

NOTE: Be careful not to trap clothing, etc., in the buckle.

For EM4350LH

1) Stand as the band plate closer to you. And let your

arms and head pass through the band.

2) The band plate sits on your back and the adjustors and

hook comes on the right side of your body when you

appropriately equip the harness.

Hanger

2 kg max

Releasing the machine

For EM4351UH, EM4350UH

To release the machine, squeeze the sides of the buckle (1) and take off the –

shoulder harness.

Be extremely careful to maintain control of the machine at this time. Do not

allow the machine to be deected toward you or anyone in the work vicinity.

WARNING: Failure to maintain complete control of the machine at all could

result in serious bodily injury or DEATH.

For EM4350LH

To release the machine, release the emergency detachment lever (2) by –

pulling strongly with ngers.

Be extremely careful to maintain control of the machine at this time. Do not

allow the machine to be deected toward you or anyone in the work vicinity.

WARNING: Failure to maintain complete control of the machine at all could

result in serious bodily injury or DEATH.

Hanging ring

For EM4351UH

You can use the ring for hanging something weighing less than 2 kg (4.4 lbs). –

NOTICE: Do not hang anything weighing more than 2 kg(4.4 lbs) on the ring.

Anything heavier on the ring can cause it to fail and the item to be

damaged.

CAUTION: Do not hang anything on the ring that can become entangled with

bushes or shrubs. Entanglement can cause loss of balance and

control resulting in personal injury.

Buckle

Band plate

(2)

EM4351UH

EM4350UH

EM4351UH

EM4350UH

EM4351UH

EM4350UH

EM4350LH

EM4351UH

EM4350LH

(1)

16

Observe the applicable accident prevention regulations!

Before starting the engine, always set the handle in the proper position.

Otherwise the cutting tool may turn suddenly and cause injury, because the

throttle cable may be pulled or bent, and open the throttle.

STARTING

Move at least 3 m away from the place of refueling. Place the unit on the ground taking care that the cutting tool does not come into contact with

the ground or any other objects.

A: Cold start

1) Set this machine on a at space.

2) Set the I-O switch (1) to OPERATION.

POINTS IN OPERATION AND HOW TO STOP

EM4350UH

EM4351UH

STOP

OPERATION

Lock-off

lever

High speed

Low speed

Throttle

lever

(1)

OPERATION

Lock-off lever

High speed

Low speed

Throttle lever

EM4350LH

STOP

(1)

3) Choke lever

Close the choke lever.

Choke opening:

- Full closing in cold or when the engine is cold.

- Full or half opening if the engine is a bit warm, such as restarting engine

just after stopping during warm-up operation.

4) Primer pump

Continue to push the primer pump until fuel comes into the primer pump. (In

general, 7 to 10 pushes.)

If the primer pump is pushed excessively, an excess of gasoline returns to

the fuel tank.

Primer pump

CLOSE

17

NOTE:

Do not pull the throttle lever unnecessarily when the engine is not running. It may cause ooding of fuel in the engine, and may cause the •

engine difcult to start up.

In case of ooding of the fuel, remove the spark plug and pull the starter handle slowly to remove excess fuel. Also, dry the electrode section •

of the spark plug.

If the engine res and stops, or stops soon after starting, return the choke lever to the OPEN position, and pull the starter knob a few times •

again to start the engine.

If the choke lever is left in the CLOSE position, and the starter knob merely pulled repeatedly, too much fuel will be sucked in, and the engine •

will become difcult to start.

Do not race the engine in warm-up operation unnecessarily.•

B: Warm start

1) Keep the choke lever full open.

2) Push the primer pump repeatedly.

3) Keep the throttle lever at the idling position.

4) Pull the recoil starter strongly.

5) If it is difcult to start the engine, release the

lock-off lever (3), pull the throttle lever (2), and

move the I-O switch (1) to the throttle lock

position. With holding the I-O switch (1), release

the throttle lever (2) and the lock-off lever (3).

Then pull the starter knob.

WARNING: Pay attention that the cutting tool

rotates immediately.

6) Once the engine starts, release the lock-off

lever (3) and pull the throttle lever (2), and

release them to make the engine idle.

OPEN

5) Recoil starter

Make sure you have a rm footing.

Hold the unit with your left hand and press it down rmly.

CAUTION: Do not stand or kneel on the throttle cable. The internal

wire may be pulled and the cutting tool may start rotating

unintentionally.

Do not open the throttle.

Pull the starter knob gently until a certain resistance is felt. Then, return the

starter knob, and pull it strongly.

Never pull the rope to the full extension. Once the starter knob is pulled,

never release your hand immediately. Hold the starter knob until it returns to

its original point.

6) Choke lever

Once engine starts, set choke lever to the OPEN position.

- Open the choke lever gradually while checking the engine operation. Be

sure to open the choke lever to the full in the end.

- In cold or when the engine is cooled down, never open the choke lever

suddenly. Otherwise the engine may stop.

7) Warm-up operation

Continue warm-up operation for 2 to 3 minutes.

NOTICE: Do not pull the throttle lever unnecessarily while the engine

is not running. It may cause fuel leak from the air cleaner. If it

happens, wipe leaked fuel off. Also, open the air cleaner cover

and clean the element and the air cleaner plate.

EM4350UH

EM4350LH

EM4351UH

EM4350UH

EM4351UH

(1)

(2)

(3)

EM4350LH

(1)

(2)

18

ADJUSTMENT OF IDLE SPEED

When it is necessary to adjust the idle speed, perform it by the carburetor adjusting screw.

CHECKUP OF IDLE SPEED

Set the idle speed to 3,000 min –

-1

.

If it is necessary to change the idle speed, use a phillips head screw driver on

the screw illustrated on the right.

To increase the idle speed, turn the adjusting screw clockwise. –

To reduce the idle speed, turn the adjusting screw counterclockwise.

The carburetor is factory adjusted. However, after several use the idle speed –

need to be re-adjusted.

STOPPING

1) Release the throttle lever (2) fully, and when the

engine rpm has lowered, set the I-O switch (1)

to STOP the engine will now stop.

2) The cutting tool continues to rotate a while

after stopping the engine. Wait until it stops

completely.

STOP

EM4350UH

EM4351UH

(1)

(2)

EM4350LH

(1)

(2)

(1)

(2)

PREVENTION FROM CARBURETOR ICING

CAUTION: When environmental temperature is higher than 10°C, always

return the shutter to normal (sun mark) setting. Otherwise the

engine may be damaged by overheating.

When the environmental temperature is low and humidity is high, water vapor

may freeze inside the carburetor and the engine drives unsteadily (carburetor

icing). Change the setting of the shutter as follows if necessary.

1. Remove the screw (1).

2. Change the direction of the shutter (2) as follows:

− Environment temperature is higher than 10°C: Set the shutter in normal

position (sun mark).

− Environment temperature is equal or lower than 10°C: Set the shutter in

anti-icing position (snow mark).

3. Tighten the screw.

19

Replacing the nylon cord (BUMP & FEED)

WARNING: Make sure that the cover of the nylon cutting head is secured to

the housing properly as described below. Failure to properly secure

the cover may cause the nylon cutting head to y apart resulting in

serious personal injury.

Press inward on the housing latches and lift upward to remove the cover.

Discard any of the remaining nylon cord.

Hook the middle of the new nylon cord to the notch located at the center of the

spool between the 2 channels provided for the nylon cord. One side of the cord

should be about 80 mm longer than the other side.

Wind both ends rmly around the spool in the direction marked on the head for

left hand direction indicated by LH.

Wind all but about 100 mm of the cords, leaving the ends temporarily hooked

through a notch on the side of the spool.

Cover

Latches

Press Press

80 mm

For left hand

rotation

Spool

100 mm

Notches

CAUTION: The cutting tools shown in the illustration are not to be sharpened.

Manual resharpening will result in imbalances of the cutting tool

causing vibrations and damage to the equipment.

NOTE: To increase the service life of the cutter blade it may be turned over

once, until both cutting edges have become blunt.

RESHARPENING THE CUTTING TOOL

NYLON CUTTING HEAD

The nylon cutting head is a dual line trimmer head that has bump & feed

mechanism.

The nylon cutting head will feed out the proper length of nylon line after tapping

the nylon cutting head on the ground by changes in centrifugal force caused by

increasing or decreasing rpms.

Operation

Increase the nylon cutting head speed to approx. 6,000 min –

-1

.

Bump the nylon cutting head lightly on the ground.

The most effective cutting area is shown by the shaded area. –

If the nylon cord does not feed out, rewind/replace the nylon cord by following –

the procedures described under “Replacing the nylon cord.”

Most effective cutting area

20

Replacing the nylon cord (ULTRA AUTO)

1. Put off cover from housing, pressing two cover locking tabs located oppositely

on side of the housing.

2. Take off tab knob and spool from the housing.

3. Put each one end of two cutting lines into each holes at innermost of the slot

on one of spool outer anges. Put the lines into spool gutters through each

slit on the anges.

Pull up

Spool

There is a hole

innermost of the slit

Slit

Tab knob

Cover

locking

tab

Mount the spool in the housing so that the grooves and protrusions on the

spool match up with those in the housing. Keep the side with letters on the

spool visible on the top. Now, unhook the ends of the cord from their temporary

position and feed the cords through the eyelets to come out of the housing.

Align the protrusion on the underside of the cover with the slots of the eyelets.

Then push cover rmly onto the housing to secure it. Make sure the latches fully

spread in the cover.

Cover

Protrusion

Slot of

eyelet

Eyelets

Страница загружается...

Makita EM4350LH, EM4350UH, EM4351UH Original Instruction Manual

Похожие модели бренда

Модели других брендов