Indesit 7OFK 899E PX RU/HA Руководство пользователя

Бренд: Indesit

Модель: 7OFK 899E PX RU/HA

Категория: Печи

Тип: Руководство пользователя

English

Operating Instructions

OVEN

Contents

Operating Instructions,1

Warnings,2

Assistance,4

Description of the appliance,5

Description of the appliance,6

Installation,7

Start-up and use,9

Modes,10

Precautions and tips,14

Maintenance and care,14

Troubleshooting,17

7OFK 899E PX RU/HA

Русскии

Руководство по эксплуатации

ДУХОВОЙ ШКАФ

Содержание

Руководство по эксплуатации,1

Предупреждения,3

Сервисное обслуживание,4

Описание изделия,5

Описание изделия,6

Установка,18

Включение и эксплуатация,20

Программы,21

Предосторожности и рекомендации,25

Техническое обслуживание и уход,26

Неисправности и методы их устранения,29

Warnings

WARNING: The appliance and its

accessible parts become hot during use.

Care should be taken to avoid touching

heating elements. Children less than 8

years of age shall be kept away unless

continuously supervised. This appliance

can be used by children aged from 8 years

and above and persons with reduced

physical, sensory or mental capabilities

or lack of experience and knowledge

if they have been given supervision

or instruction concerning use of the

appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and

user maintenance shall not be made by

children without supervision.

Do not use harsh abrasive cleaners or

sharp metal scrapers to clean the oven door

glass since they can scratch the surface,

which may result in shattering of the glass.

Before initiating the automatic cleaning

cycle:

• clean the oven door;

• remove large or coarse food residues

from the inside of the oven using a

damp sponge. Do not use detergents;

• remove all accessories and the sliding

rack kit (where present);

• do not place tea towels”

Keep children away from the appliance

during the automatic cleaning cycle as

surfaces may become very hot.

Never use steam cleaners or pressure

cleaners on the appliance.

WARNING: Ensure that the appliance is

switched off before replacing the lamp to

avoid the possibility of electric shock.

! When you place the rack inside, make

sure that the stop is directed upwards and

in the back of the cavity.

Предупреждения

ВНИМАНИЕ: Данное изделие и его

доступные комплектующие сильно

нагреваются в процессе эксплуатации.

Будьте осторожны и не касайтесь

нагревательных элементов.

Не разрешайте детям младше 8 лет

приближаться к изделию без контроля.

Данное изделие может быть

использовано детьми старше 8 лет и

лицами с ограниченными физическими,

сенсорными или умственными

способностями или без опыта и знания

о правилах использования изделия при

условии надлежащего контроля или

обучения безопасному использованию

изделия с учетом соответствующих

рисков. Не разрешайте детям играть

с изделием. Не разрешайте детям

осуществлять чистку и уход за

изделием без контроля взрослых.

Не используйте абразивные вещества

или режущие металлические скребки

для чистки стеклянной дверцы духового

шкафа, так как они могут поцарапать

поверхность, что может привести к

разбиванию стекла.

Подготовка к автоматической чистке:

• протрите дверцу духовки

• влажной губкой удалите из духовки

наиболее крупные загрязнения. Не

используйте моющие средства;

• выньте все съемные детали и

комплект выдвижных направляющих

(если имеется);

• не вешайте тряпки или кухонные

полотенца на ручку дверцы духового

шкафа.

В процессе пиролитической чистки

поверхности могут сильно нагреться:

не разрешайте детям приближаться к

духовому шкафу.

Никогда не используйте паровые

чистящие агрегаты или агрегаты под

высоким давлением для чистки изделия.

ВНИМАНИЕ: Проверьте, чтобы изделие

было выключено, перед заменой

лампочки во избежание возможных

ударов током.

! При установке решетки проверить,

чтобы фиксатор был повернут вверх

с задней стороны выемки.

Assistance

Warning:

The appliance is tted with an automatic diagnostic system

which detects any malfunctions. Malfunctions are signalled

through messages of the following type: “F—” followed by

numbers.

Call for technical assistance in the event of a malfunction.

Before calling for Assistance:

• Check whether you can x the problem yourself.

• Restart the programme to check whether the malfunction

has disappeared.

• If it has not, contact the Authorised Technical Assistance

Service.

! Never use the services of an unauthorised technician.

Please have the following information to hand:

• The type of problem encountered.

• The message shown on the TEMPERATURE display.

• The appliance model (Mod.).

• The serial number (S/N).

The latter two pieces of information can be found on the

data plate located on the appliance.

Сервисное обслуживание

Внимание:

Изделие оснащено системой автоматической

диагностики, позволяющей выявить возможные

неисправности. Неисправности показываются на

дисплее посредством следующих сообщений: “F—” с

последующими цифрами.

В этом случае необходимо вызвать техника из центра

сервисного обслуживания.

Перед тем как обратиться в Центр Технического

обслуживания:

• Проверьте, можно ли устранить неисправность

самостоятельно;

• Вновь запустите программу для проверки

исправности машины;

• В противном случае обратитесь в уполномоченный

Центр Технического обслуживания.

! Никогда не обращайтесь к неуполномоченным

техникам.

При обращении в Центр Технического Обслуживания

необходимо сообщить:

• Тип неисправности;

• сообщение, показываемое на дисплее

ТЕМПЕРАТУРЫ

• Модель изделия (Мод.)

• Номер тех. паспорта (серийный №)

Эти данные вы найдете на паспортной табличке,

расположенной на изделии.

Description of the appliance

Overall view

1 POSITION 1

2 POSITION 2

3 POSITION 3

4 POSITION 4

5 POSITION 5

6 GUIDES for the sliding racks

7 DRIPPING PAN

8 GRILL

9 Control panel

Описание изделия

Общии вид

1 ПОЛОЖЕНИЕ 1

2 ПОЛОЖЕНИЕ 2

3 ПОЛОЖЕНИЕ 3

4 ПОЛОЖЕНИЕ 4

5 ПОЛОЖЕНИЕ 5

6 ВЫДВИЖНЫЕ НАПРАВЛЯЮЩИЕ уровней

7 ПРОТИВЕНЬ

8 РЕШЕТКА

9 Панель управления

9 6

Description of the appliance

Control panel

1 SELECTOR knob

2 CONTROL PANEL POWER BUTTON

3 DISPLAY

4 THERMOSTAT / TIMER knob

5 START / STOP

6 FAST CLEAN Icon

7 MINUTE MINDER icon

8 TIMER icon

9 DOOR / CONTROL PANEL LOCK icon

10 LIGHT icon

Display

11 TEMPERATURE and TIME numerical digits

12 DURATION icon

13 END OF COOKING icon

14 CLOCK icon

15 MINUTE MINDER icon

16 DOOR LOCK indicator

17 CONTROL PANEL LOCK indicator

18 Preheating /Residual heat indicator

19 MODE icons

Описание изделия

Панель управления

1 Рукоятка ПРОГРАММЫ

2 ВКЛЮЧЕНИЕ КОНСОЛИ УПРАВЛЕНИЯ

3 ДИСПЛЕЙ

4 Рукоятка ТЕРМОСТАТА / НАСТРОЙКИ

ПРОДОЛЖИТЕЛЬНОСТИ

5 ПУСК / ОСТАНОВКА

6 Символ FAST CLEAN

7 Символ ТАЙМЕР

8 Символ НАСТРОЙКА ВРЕМЕНИ

9 Символ БЛОКИРОВКА ДВЕРЦЫ / УПРАВЛЕНИЙ

10 Символ ОСВЕЩЕНИЕ

Дисплей

11 Цифровые значения ТЕМПЕРАТУРЫ и ВРЕМЕНИ

12 Символ ПРОДОЛЖИТЕЛЬНОСТЬ

13 Символ КОНЕЦ ПРИГОТОВЛЕНИЯ

14 Символ ЧАСЫ

15 Символ ТАЙМЕР

16 Индикатор ДВЕРЦА ЗАБЛОКИРОВАНА

17 Индикатор БЛОКИРОВКИ КОНСОЛИ УПРАВЛЕНИЯ

18 Индикатор Нагрева / Остаточного тепла

19 Символы ПРОГРАММ

Installation

! Please keep this instruction booklet in a safe place for

future reference. If the appliance is sold, given away or

moved, please make sure the booklet is also passed on to

the new owners so that they may benet from the advice

contained within it.

! Please read this instruction manual carefully: it contains

important information concerning the safe operation,

installation and maintenance of the appliance.

Positioning

! Do not let children play with the packaging material; it

should be disposed of in accordance with local separated

waste collection standards (see Precautions and tips).

! The appliance must be installed by a qualied professional

in accordance with the instructions provided. Incorrect

installation may damage property or cause harm to people

or animals.

Built-in appliances

Use an appropriate cabinet to ensure that the appliance

operates properly:

• The panels adjacent to the oven must be made of heat-

resistant material.

• Cabinets with a veneer exterior must be assembled with

glues which can withstand temperatures of up to 100°C.

• To install the oven under the counter (see diagram) or

in a kitchen unit, the cabinet must have the following

dimensions:

590 mm.

595 mm.

22,5 mm.*

20,5 mm.

550 mm.

570 mm.

20 mm.

575-585 mm.

45 mm.

560 mm.

550 mm.

min.

* Stainless steel models only

! The appliance must not come into contact with electrical

parts once it has been installed.

The indications for consumption given on the data plate

have been calculated for this type of installation.

Ventilation

To ensure adequate ventilation, the back panel of the

cabinet must be removed. It is advisable to install the oven

so that it rests on two strips of wood, or on a completely

at surface with an opening of at least 45 x 560 mm (see

diagrams).

560 mm.

45 mm.

Centring and xing

Secure the appliance to the cabinet:

• Open the oven door.

• slide out the side gaskets at the top until the 2 xing holes

are exposed;

• Fix the oven to the cabinet using the 2 wood screws.

• reposition the 2 gaskets.

! All parts which ensure the safe operation of the appliance

must not be removable without the aid of a tool.

Electrical connection

Ovens equipped with a three-pole power supply cable are

designed to operate with alternating current at the voltage

and frequency indicated on the data plate located on the

appliance (see below).

Fitting the power supply cable

1. Open the terminal board

by inserting a screwdriver

into the side tabs of the

cover. Use the screwdriver

as a lever by pushing it

down to open the cover (see

diagram).

2. Install the power supply

cable by loosening the

cable clamp screw and the

three wire contact screws

L-N- .

Connect the wires to the

corresponding terminals:

the Blue wire to the terminal

marked (N), the Brown wire

to the terminal marked (L)

and the Yellow/Green wire

to the terminal marked

(see diagram).

3. Secure the cable by fastening the clamp screw.

4. Close the cover of the terminal board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate (see table).

The appliance must be directly connected to the mains using

an omnipolar switch with a minimum contact opening of 3

mm installed between the appliance and the mains. The

switch must be suitable for the charge indicated and must

comply with current electrical regulations (the earthing wire

must not be interrupted by the switch). The supply cable

must be positioned so that it does not come into contact

with temperatures higher than 50°C at any point (the back

panel of the oven, for example).

! The installer must ensure that the correct electrical

connection has been performed and that it is fully compliant

with safety regulations.

Before connecting the appliance to the power supply, make

sure that

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate.

• The voltage is in the range between the values indicated

on the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these

safety measures not be observed.

APPLIANCE SPECIFICATIONS

Dimensions*

width 43.5 cm

height 32,4 cm

depth 41.5 cm

Volume*

59 l

Dimensions**

width 45.5 cm

height 32,4 cm

depth 41.5 cm

Volume**

62 l

Electrical

connections

voltage: 220 - 240 V~ 50/60 Hz or

50 Hz (see data plate)

maximum power absorbed

2800 W

ENERGY

LABEL

Directive 2002/40/EC on the label

of electric ovens. Standard EN 50304

Declared energy consumption

for Forced convection Class –

heating mode:

ECO.

* Only for models with drawn rails.

** Only for models with wire rails.

This appliance conforms to the following

European Economic Community

directives:

- 2006/95/EEC dated 12/12/06 (Low

Voltage) and subsequent amendments.

- 2004/108/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments.

- 93/68/EEC dated 22/07/93 and

subsequent amendments.

- 2012/19/EC and subsequent

amendments.

- 1275/2008 standby/off mode.

Start-up and use

WARNING! The oven is

provided with a stop system

to extract the racks and

prevent them from coming

out of the oven (1).

As shown in the drawing,

to extract them completely,

simply lift the racks, holding

them on the front part, and

pull (2).

! The rst time you use your appliance, heat the empty oven with

its door closed at its maximum temperature for at least half an

hour. Make sure that the room is well ventilated before switching

the oven off and opening the oven door. The appliance may emit

a slightly unpleasant odour caused by protective substances

used during the manufacturing process burning away.

! To make the setting process easier, keep the knob in

position: this will increase the scrolling speed of the numbers

on the display.

! Each setting will automatically be stored in the appliance

memory after 10 seconds.

! The touch controls cannot be activated if the user is

wearing gloves.

Some models are equipped with a system of hinges which

allows the door to close slowly, without the user having to

follow the movement through with his/her hand. To use the

system correctly, before closing the door:

• Open the door fully.

• Do not force the closing movement manually.

! In order to optimise the cooking performance, when

starting the selected function, product settings will be

applied that could cause a delayed start of the fan and

heating elements.

Control panel lock

! The control panel can be locked while the oven is off, once

cooking has started or nished and during programming.

To lock the door and the oven controls, press and hold the

button for at least 2 seconds. A buzzer sounds and the

display shows the key symbol “n—O”. The and

icons, when lit, indicate lock function activation.

To deactivate the lock, press and hold the button again

for at least 2 seconds.

! When cleaning the appliance, the door lock may be closed

accidentally (there is an exposed spring). If this happens,

reopen it by turning the door lock upwards (see gure).

KO OK

Setting the clock

! The clock can only be set when the oven is switched off. If

the oven is in standby mode, pressing the button once will

display the current time setting. Press it again to set the time.

After connection to the power supply network or after a

blackout, the button and the digits on the display will

ash for 10 seconds.

To set the clock:

1. Press button .

2. Turn the TIMER knob towards “ ” and “ ” to adjust the

hour value.

3. Once you have reached the correct hour value, press

the button.

4. Repeat the above process to set the minutes.

If a blackout occurs, it will be necessary to reset the clock.

If the icon ashes on the display, this indicates that the

clock has not been set correctly.

Setting the minute minder

! The minute minder may still be set whether the oven is

switched on or off. It does not switch the oven on or off.

When the set time has elapsed, the timer emits a buzzer

that will automatically stop after 30 seconds or when any

active button on the control panel is pressed.

To adjust the timer proceed as follows:

1. Press button .

2. Adjust the time as desired by turning the TIMER knob

towards “ ” and “ ”.

3. Once you have reached the desired value, press the

button again.

The lit symbol will remind you that the minute minder

is on. The DISPLAY will show the countdown.

To cancel the minute minder, press the button and use

the knob to set the time to 00:00. Press button again.

The icon will switch off to indicate that the minute minder

has been disabled.

Starting the oven

1. Switch the control panel on by pressing the button.

The appliance buzzer sounds three times (ascending) and

all buttons light up in sequence.

2. Select the desired cooking mode by turning the

SELECTOR knob. The display shows:

- the temperature associated with the mode, if programming

manually;

- “Auto” and the duration alternately, if programming is

automatic.

3. Press the button to begin cooking.

4. The oven will begin its preheating phase, the preheating

indicators will light up as the temperature rises.

5. When the preheating process has nished, a buzzer sounds

and all the preheating indicator lights show that this stage has

been completed: the food can then be placed in the oven.

6. During cooking it is always possible to:

- modify the temperature by turning the THERMOSTAT

knob (manual modes only);

- set the duration of a cooking mode (see Cooking Modes);

- press the button to stop cooking. In this case the

appliance stores the temperature modied previously in its

memory (manual modes only);

- switch off the oven by pressing the button for 3 seconds.

7. If a blackout occurs while the oven is already in operation,

an automatic system within the appliance will reactivate the

cooking mode from the point at which it was interrupted,

provided that the temperature has not dropped below a

certain level. Programmed cooking modes which have not

yet started will not be restored and must be reprogrammed

(for example: a cooking mode has been programmed to

start at 20:30. At 19:30 a blackout occurs. When the power

supply is restored, the mode will have to be reprogrammed).

! There is no preheating stage for the GRILL mode.

! Never put objects directly on the bottom of the oven; this

will prevent the enamel coating from being damaged.

! Always place cookware on the rack(s) provided.

! The oven will begin its preheating phase after 2 seconds

from selecting the desired cycle.

Cooling ventilation

In order to cool down the external temperature of the oven,

a cooling fan blows a stream of air between the control

panel and the oven door, as well as towards the bottom

of the oven door.In the FAST COOKING mode, the fan is

activated automatically.

! Once cooking has been completed, the cooling fan

continues to operate until the oven has cooled down

sufciently.

Oven light

The light comes on when the oven door is opened or when

a cooking mode starts. When models featuring LED INSIDE

technology begin cooking, the LEDs on the door light up for

improved illumination of all cooking levels.

The button can be used to switch on the light at any time.

Residual heat indicators

The appliance is tted with a residual heat indicator. When

the oven is off, the “residual heat” bar on the display lights

up to indicate high temperatures inside the oven cavity. The

individual segments of the bar switch off one by one as the

temperature inside the oven falls.

Restoring the factory settings

The oven factory settings can be restored to reset all

selections made by the user (clock and customised

durations). To carry out a reset, switch off the oven, then keep

the SELECTOR knob turned while pressing the button

for 6 seconds. Once the restore procedure is complete, a

buzzer will sound. The rst time the button is pressed, the

oven will behave as if it is being switched on for the rst time.

Standby

This product complies with the requirements of the latest

European Directive on the limitation of power consumption

of the standby mode. If no buttons are pressed for 30

minutes and the control panel/door lock has not been

activated, the appliance automatically reverts to standby

mode. The standby mode is visualised by the high luminosity

“Watch Icon”. As soon as interaction with the machine

resumes, the system’s operating mode is restored.

Modes

! In order to guarantee wonderfully soft and crunchy

foodstuffs, the oven releases – in the form of water vapour -

the humidity naturally withheld in the food itself. In this way,

optimal cooking results can be achieved for all types of food.

! Every time the oven is switched on, it suggests the rst

manual cooking mode.

Manual cooking modes

! All cooking modes have a default cooking temperature

which may be adjusted manually to a value between

30°C and 250°C as desired (300°C for GRILL mode). Any

temperature adjustments will be stored in the appliance

memory and suggested again the next time this mode

is used. If the selected temperature is higher than the

temperature inside the oven, the text “Hot” appears on the

display. However, it will still be possible to start cooking.

MULTILEVEL mode

Since the heat remains constant throughout the oven, the

air cooks and browns food in a uniform manner. A maximum

of two racks may be used at the same time.

BARBECUE mode

The top heating element and the rotisserie spit (where

present) are activated. The high and direct temperature

of the grill is recommended for food which requires a high

surface temperature. Always cook in this mode with the oven

door closed (see “Practical cooking advice”).

FAN GRILLING mode

The top heating element and the rotisserie spit (where present)

are activated and the fan begins to operate. During part of

the cycle the circular heating element is also activated. This

combination of features increases the effectiveness of the

unidirectional thermal radiation provided by the heating elements

through the forced circulation of the air throughout the oven.

This helps prevent food from burning on the surface and allows

the heat to penetrate right into the food. Always cook in this

mode with the oven door closed (see “Practical cooking advice”).

FAST COOKING mode

This mode is particularly suitable for cooking pre-packed

food quickly (frozen or pre-cooked). The best results are

achieved using one cooking rack only.

LOW TEMPERATURE modes

This type of cooking can be used for proving, defrosting,

preparing yoghurt, heating dishes at the required speed and

slow cooking at low temperatures. The temperature options

are: 40, 65 and 90°C.

BAKING mode

The rear heating element and the fan are switched on, thus

guaranteeing the distribution of heat in a delicate and uniform

manner throughout the entire oven. This mode is ideal for baking

temperature sensitive foods (such as cakes, which need to rise).

PIZZA modes

The top and circular heating elements switch on and the fan

begins to operate. This combination heats the oven rapidly.

If you use more than one rack at a time, switch the position

of the dishes halfway through the cooking process.

ECO mode

The rear heating element and the fan are switched on,

thus guaranteeing the distribution of heat in a delicate and

uniform manner throughout the entire oven.This energy

saving mode is recommended for small dishes, ideal for

heating foods and nishing off cooking.

Rotisserie spit*

To operate the rotisserie

function (see diagram)

proceed as follows:

1. Place the dripping pan in

position 1.

2. Place the rotisserie

support in position 3 and

insert the spit in the hole

provided on the back panel

of the oven.

3. Start the rotisserie

function by selecting the or modes;

! When modes or are activated, the rotisserie will

stop if the door is opened.

Automatic cooking modes

! The temperature and cooking duration are pre-set values,

guaranteeing a perfect result every time - automatically. These

values are set using the C.O.P.® (Programmed Optimal

Cooking) system. The cooking cycle stops automatically and

the oven indicates when the dish is cooked. You may start

cooking whether the oven has been preheated or not. The

cooking duration can be customised according to personal

taste by modifying the relevant value - before cooking begins

- by ±5/20 minutes depending on the selected programme.

The duration can however be modied even once cooking has

begun. If the value is modied before the programme begins, it

is stored in the memory and suggested again by the appliance

when the programme is next used. If the temperature inside

the oven is higher than the suggested value for the selected

mode, the text “Hot” appears on the display and it will not be

possible to begin cooking; wait for the oven to cool.

! When the cooking stage has been reached, the oven

buzzer sounds.

! Do not open the oven door as this will disrupt the cooking

time and temperature.

BAKED CAKES mode

This function is ideal for cooking desserts which are made

using natural yeast, baking powder and desserts which

contain no yeast. Place the dish in the oven while it is still

cold. The dish may also be placed in a preheated oven.

BREAD mode

Use this function to bake bread. To obtain the best results, we

recommend that you carefully observe the instructions below:

• follow the recipe;

• do not exceed the maximum weight of the dripping pan;

• remember to pour 50 g (0,5 dl) of cold water into the

baking tray in position 5.

• The dough must be left to rise at room temperature for

1 – 1 ½ hours (depending on the room temperature) or

until the dough has doubled in size.

Recipe for BREAD:

1 Dripping pan holding 1000 g Max, lower level

2 Dripping pans each holding 1000 g Max, medium and

lower levels

Recipe for 1000 g of dough: 600 g our, 360 g water, 11g

salt, 25 g fresh yeast (or 2 sachets of powder yeast)

Method:

• Mix the our and salt in a large bowl.

• Dilute the yeast in lukewarm water (approximately 35

degrees).

• Make a small well in the mound of our.

• Pour in the water and yeast mixture.

• Knead the dough by stretching and folding it over itself

with the palm of your hand for 10 minutes until it has a

uniform consistency and is not too sticky.

• Form the dough into a ball shape, place it in a large bowl

and cover it with transparent plastic wrap to prevent the

surface of the dough from drying out. Select the manual

LOW TEMPERATURE function on the oven and set the

temperature to 40°C. Place the bowl inside and leave

the dough to rise for approximately 1 hour (the dough

should double in volume).

• Cut the dough into equal sized loaves.

• Place them in the dripping pan, on a sheet of baking

paper.

• Dust the loaves with our.

• Make incisions on the loaves.

• Place the food inside the oven while it is still cold.

• Start the BREAD cooking mode.

• Once baked, leave the loaves on one of the grill racks

until they have cooled completely.

Programming cooking

! A cooking mode must be selected before programming

can take place.

Programming the cooking duration

1. Press the button until the icon and the numerical

digits on the display begin to ash.

* Only available in certain models.

2. Turn the TIMER knob towards “ ” and “ ” to adjust the

time as desired; keep the knob in position to scroll through the

numbers more quickly and make the setting process easier.

3. Once you have reached the desired duration, press the

button again. The display will show the duration and

set temperature alternately.

4. Press the button to begin cooking.

5. When cooking has nished, “END” appears on the display

and a buzzer sounds.

• For example: it is 9:00 a.m. and a duration of 1 hour and

15 minutes is programmed. The programme will stop

automatically at 10:15 a.m.

Setting the end time for a cooking mode

! A cooking duration must be set before the cooking end

time can be scheduled.

! For the delayed programming to work properly, the clock

should be set to the correct time.

1. Follow steps 1 to 3 to set the duration as detailed above.

2. Press the button twice: the icon and the

numerical digits on the display will begin to ash.

3. Turn the TIMER knob towards “ ” and “ ” to adjust the

cooking end time value.

4. Once you have reached the desired end time, press the

button again. The display will show the duration, the

cooking end time and the set temperature alternately.

5. Press the button to activate the programmed mode.

Programming has been set when the and buttons

are illuminated. The DISPLAY shows the cooking end time

and the cooking duration alternately.

6. Once cooking has nished, “END” appears on the display

and a buzzer sounds.

• For example: it is 9:00 a.m. and a time of 1 hour and 15

minutes is programmed, while the end time is set to 12:30.

The programme will start automatically at 11:15 a.m.

To cancel programming press the button.

Practical cooking advice

! Do not place racks in position 1 and 5 during fan-assisted

cooking. This is because excessive direct heat can burn

temperature sensitive foods.

! In the GRILL and FAN GRILLING cooking modes,

particularly when using the rotisserie spit, place the dripping

pan in position 1 to collect cooking residues (fat and/or

grease).

MULTILEVEL

• Use positions 2 and 4, placing the food which requires

more heat on 2.

• Place the dripping pan on the bottom and the rack on

top.

BARBECUE

• Place the rack in position 3 or 4. Position the food in the

centre of the rack.

• We recommend that the temperature is set to its

maximum level. The top heating element is regulated by

a thermostat and may not always operate constantly.

PIZZA OVEN

• Use a lightweight aluminium pizza pan. Place it on the

rack provided.

For a crispy crust, do not use the dripping pan as this

extends the total cooking duration and prevents the crust

from forming.

• If the pizza has a lot of toppings, we recommend adding

the mozzarella cheese to the top of the pizza halfway

through the cooking process.

Modes Foods Weight

(Kg)

Preheating

Manual

standard

guide rails

sliding

guide rails

Multilevel*

Pizza on 2 racks

Pies on two racks/cakes on 2 racks

Sponge cake on 2 racks (on the dripping pan)

Roast chicken + potatoes

Lamb

Mackerel

Lasagne

Cream puffs on 3 racks

Biscuits on 3 racks

Cheese puffs on 2 racks

Savoury pies

1+1

2 and 4

1 and 2/3

1 or 2

2 and 4

1 and 3

yes

20-25

30-35

20-25

65-75

45-50

30-35

35-40

20-25

10-20

20-25

20-30

Grill*

Mackerel

Sole and cuttlefish

Squid and prawn kebabs

Cod fillet

Grilled vegetables

Veal steak

Sausages

Hamburgers

Toasted sandwiches (or toast)

Spit-roast chicken using rotisserie spit (where present)

Spit-roast lamb using rotisserie spit (where present)

0,7

0,5

0,8

0,7

n° 4 or 5

n° 4 or 6

3 or 4

2 or 3

300

15-20

10-15

8-10

10-15

15-20

10-12

3-5

70-80

Fan grilling*

Grilled chicken

Cuttlefish

Spit-roast chicken using rotisserie spit (where present)

Spit-roast duck using rotisserie spit (where present)

Roast veal or beef

Roast pork

Lamb

1,5

210

200

210

55-60

30-35

70-80

60-70

60-75

70-80

40-45

Fast cooking*

Frozen food

Pizza

Courgette and prawn pie

Country style spinach pie

Turnovers

Lasagne

Golden rolls

Chicken bites

0.3

0.4

0.5

0.3

0.5

0.4

250

200

220

200

180

220

30-35

25-30

15-20

Pre-cooked food

Golden chicken wings

0.42 1- 200 20-25

Fresh Food

Biscuits (shortcrust pastry)

Sponge cake made with yoghurt

Cheese puffs

0.3

0.6

0.2

200

180

210

15-18

10-12

Low

temperature*

Baking*

Tarts

Fruit cakes

Sponge cake made with yoghurt

Small cakes on 2 racks

Sponge cake

Cream puffs on 3 racks

Biscuits on 3 racks

Filled pancakes

Meringues on 3 racks

Cheese puffs

0,5

0,7

0,6

0,7

0,8

0,5

2 or 3

2 and 4

2 or 3

1, 3 and 5

1 or 2

1 and 3

1 or 2

1, 2 and 4

yes

180

170-180

180-190

160-170

180-190

180

200

210

25-35

40-50

45-55

20-25

30-40

20-25

30-35

180

20-25

Pizza*

Pizza

Focaccia bread

0,5

yes

15-20

20-25

Automatic**

Baked cakes

Baked cakes 12 or 32 no

Bread***

Bread (see recipe) 11 or 21 no

The cooking times listed above are intended as guidelines only and may be modified according to personal tastes. Oven preheating times are set as

standard and may not be modified manually.

** The duration of the automatic cooking functions are set by default. The values can be modified by the user, starting with th

e default duration.

*** As stated in the recipe, pour 50 g (0,5 dl) water into the dripping pan in position 5.

! ECO programme:

This programme guarantees sensible energy saving – is recommended for dishes such as fish fillets, small pastries and vegetables.

It is also suitable for warmin

foodstuffs and for completin

cookin

Cooking advice table

Rack position Recommended

Temperature

(°C)

Cooking

duration

(minutes)

1 and 3 and 5

1 and 2 and 4

210-220

190-200

210-220

180

160-170

200-210

190-200

180

180-190

190

180

210

190-200

Proving / Defrosting

White meringues

Meat / Fish

8-12 ore

90-180

Precautions and tips

! This appliance has been designed and manufactured

in compliance with international safety standards. The

following warnings are provided for safety reasons and

must be read carefully.

General safety

• The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial use.

• The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain and storms.

• When moving or positioning the appliance, always use

the handles provided on the sides of the oven.

• Do not touch the appliance while barefoot or with wet or

damp hands and feet.

• The appliance must be used by adults only for

the preparation of food, in accordance with the

instructions provided in this booklet. Any other

use of the appliance (e.g. for heating the room)

constitutes improper use and is dangerous. The

manufacturer may not be held responsible for any

damage caused as a result of improper, incorrect

and unreasonable use of the appliance.

• Do not touch the heating elements or certain parts

of the oven door when the appliance is in use; these

parts become extremely hot. Keep children well away

from the appliance.

• Make sure that the power supply cables of other electrical

appliances do not come into contact with the hot parts of

the oven.

• The ventilation and heat dispersal openings must never

be obstructed.

• Always grip the oven door handle in the centre: the ends

may be hot.

• Always use oven gloves when placing cookware in the

oven or when removing it.

• Do not use aluminium foil to line the bottom of the oven.

• Do not place ammable materials in the oven: if the

appliance is switched on accidentally, the materials could

catch re.

• When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

• Do not perform any cleaning or maintenance work without

having disconnected the appliance from the electricity

mains.

• If the event of malfunctions, under no circumstances

should you attempt to perform the repairs yourself.

Contact an authorised Service Centre (see Assistance).

• Do not rest objects on the open oven door.

• Do not let children play with the appliance.

• The appliance should not be operated by people (including

children) with reduced physical, sensory or mental

capacities, by inexperienced individuals or by anyone

who is not familiar with the product. These individuals

should, at the very least, be supervised by someone who

assumes responsibility for their safety or receive preliminary

instructions relating to the operation of the appliance.

• The appliance is not intended to be operated by

means of an external timer or separate remote-

control system.

Disposal

• When disposing of packaging material: observe local

legislation so that the packaging may be reused.

• The European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment (WEEE), requires

that old household electrical appliances must not

be disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the product

reminds you of your obligation, that when you dispose

of the appliance it must be separately collected.

Consumers should contact their local authority or retailer

for information concerning the correct disposal of their

old appliance.

Respecting and conserving the environment

• You can help to reduce the peak load of the electricity

supply network companies by using the oven in the

hours between late afternoon and the early hours of

the morning. The cooking mode programming options,

the “delayed cooking” mode (see Cooking modes) and

“delayed automatic cleaning” mode (see Care and

Maintenance) in particular, enable the user to organise

their time efciently.

• Always keep the oven door closed when using the GRILL

and FAN GRILLING modes: this will achieve improved

results while saving energy (approximately 10%).

• Check the door seals regularly and wipe them clean

to ensure they are free of debris so that they adhere

properly to the door, thus avoiding the dispersal of heat.

! This product complies with the requirements of the latest

European Directive on the limitation of power consumption

of the standby mode.

Maintenance and care

Switching the appliance off

Disconnect your appliance from the electricity supply before

carrying out any work on it.

Cleaning the appliance

• Slight differences in colour on the front of the oven are due

to the different materials used, i.e. glass, plastic or metal.

• Any shady areas resembling grooves on the oven door

glass are caused by reections from the oven light.

• The enamel is branded at very high temperatures. This

process may cause colour variations. This is normal and

will not affect appliance operation in any way. The thin

edges of the sheet metal cannot be entirely enamelled

and may therefore appear to be unnished. This will not

affect the rust protection.

• The stainless steel or enamel-coated external parts and

the rubber seals may be cleaned using a sponge that

has been soaked in lukewarm water and neutral soap.

Use specialised products for the removal of stubborn

stains. After cleaning, rinse and dry thoroughly. Do not

use abrasive powders or corrosive substances.

• The inside of the oven should ideally be cleaned after

each use, while it is still lukewarm. Use hot water and

detergent, then rinse well and dry with a soft cloth. Do

not use abrasive products.

• All accessories - with the exception of the sliding racks

- can be washed like everyday crockery, and are even

dishwasher safe.

• We recommend that detergents are not sprayed directly

onto the control panel, but that a sponge is used instead.

! Never use steam cleaners or pressure cleaners on the

appliance.

Cleaning the oven door

! The door of LED INSIDE models cannot be removed.

Clean the glass part of the oven door using a sponge and

a non-abrasive cleaning product, then dry thoroughly with

a soft cloth. Do not use rough abrasive material or sharp

metal scrapers as these could scratch the surface and cause

the glass to crack.

For more thorough cleaning purposes, the oven door may

be removed:

1. Open the oven door fully (see diagram).

2. Use a screwdriver to lift up and turn the small levers F

located on the two hinges (see diagram).

3. Grip the door on the two outer

sides and close it approximately

half way. Pull the door towards you,

lifting it out of its slot (see diagram).

To replace the door, reverse this

sequence.

Inspecting the seals

Check the door seals around the oven regularly. If the seals

are damaged, please contact your nearest Service Centre

(see Assistance). We recommend that the oven is not used

until the seals have been replaced.

Replacing the light bulb

To replace the oven light

bulb:

1. Remove the glass cover

of the lamp-holder.

2. Remove the light bulb and

replace it with a similar one:

halogen lamp voltage 230 V,

wattage 25 W, cap G 9.

3. Replace the glass cover

(see diagram).

Glass cover

Lamp

Holder

compartment

! Do not touch the light bulb directly with your hands.

! Do not use the oven lamp as/for ambient lighting.

Sliding rack kit assembly

To assemble the sliding

racks:

1. Remove the two frames,

lifting them away from the

spacers A (see gure).

2. Choose which shelf to use

with the sliding rack. Paying

attention to the direction in

which the sliding rack is to

be extracted, position joint B

and then joint C on the

frame.

3. Secure the two frames

with the guide rails using the

holes provided on the oven

walls (see diagram). The

holes for the left frame are

situated at the top, while the

holes for the right frame are

at the bottom.

4. Finally, t the frames on

the spacers A.

! Do not place the sliding racks in position 5.

Automatic cleaning with the FAST CLEAN

function

With the FAST CLEAN mode, the internal temperature of the

oven reaches 500°C. The pyrolytic cycle is activated, burning

away food and grime residues. Dirt is literally incinerated.

Keep children away from the appliance during the automatic

cleaning cycle as surfaces may become very hot. Particles

may ignite inside the oven as a result of the combustion

process. There is no cause for concern: this process is both

normal and hazard-free.

Before initiating the FAST CLEAN mode:

• clean the oven door;

• remove large or coarse food residues from the inside of

the oven using a damp sponge. Do not use detergents;

• remove all accessories and the sliding rack kit (where

present);

• do not place tea towels or pot holders over the oven

handle.

Left

guide rail

Right guide

rail

Direction

of extraction

! If the oven is too hot, the pyrolytic cycle may not start.

Wait for the oven to cool down.

! The programme may only be started once the oven door

has been closed.

To activate the Fast Clean programme:

1. Switch the control panel on by pressing the button.

2. Press the , the display will show the text “Piro”, “nor”

and the default duration of 1:30 h (normal cycle) alternately.

3. Press button , then turn the TIMER knob to adjust the

default cleaning level. There are 3 different levels to choose

from, each with a pre-set duration which cannot be modied:

1. Economy (ECO): turn the knob towards “ ”. Duration

1 hour.

2. Normal (NOR): initial level. Duration 1 hour and 30

minutes.

3. Intensive (INT): turn the knob towards “ ”. Duration 2

hours.

4. Press the button to conrm.

5. Press the button to begin the cleaning cycle.

An end time for the FAST CLEAN cycle (as for a normal

cooking cycle) may be programmed (see Programming the

automatic cleaning end time).

! The desired Fast Clean mode will be conrmed and started

automatically if the CLOCK icon button is not pressed within

10 seconds from selecting the cooking time.

Safety devices

• the door locks automatically as soon as the temperature

reaches a high value; the icon lights up on the display;

• pressing the button cancels the cleaning cycle t any

time;

• if a malfunction occurs, the heating elements will be

switched off;

• once the oven door has been locked, you cannot change

the duration and end time settings.

Programming the automatic cleaning end time

1. Press the button twice: the icon and the

numerical digits on the display will begin to ash.

2. Turn the TIMER knob towards “ ” and “ ” to adjust the

cleaning end time value.

3. Once you have reached the desired end time, press the

button again. The display will show the duration, the

cleaning end time and the set cleaning level alternately.

4. Press the button to activate the programmed mode.

Programming has been set when the and buttons

are illuminated.

5. Once cleaning has nished, “END” appears on the display

and a buzzer sounds.

• For example: it is 9:00 a.m. and the Economy (ECO)

FAST CLEAN level has been selected, with the default

duration of 1 hour. 12:30 is scheduled as the end time.

The programme will start automatically at 11:30 a.m.

To cancel programming press the button.

Once the automatic cleaning cycle is over

Before you can open the oven door, you will have to wait

for the icon to switch off: this indicates the oven

temperature has dropped to an acceptable level. You will

notice some white dust deposits on the bottom and the sides

of your oven; remove these deposits with a damp sponge

once the oven has cooled down completely. Alternatively,

you can make use of the already heated oven, in which

case it is not necessary to remove the deposits, they are

completely harmless and will not affect your food in any way.

NOTICE

Do not place

or rest anything

on the open door

Make sure that the racks

and dripping pans have been

inserted fully before closing the door

Please read the manual

carefully for information

regarding the automatic

cleaning (pyrolytic) cycle

Problem

Possible cause

Solution

The appliance has just been

connected to the electricity mains

or there has been a blackout.

Set the clock.

A programmed cooking mode

does not start.

There has been a blackout. Reprogram the cooking mode.

Only the high luminosity

“Clock button” is lit.

The appliance is in standby mode Press any button to exit

standby mode.

The temperature inside the oven

is higher than the suggested

value for the selected mode.

Wait for the oven to cool down.

Fan-assisted cooking has been

selected and the food looks burnt.

Positions 1 and 5: the direct

heat could cause

temperature-sensitive

foods to burn.

We recommend switching

dripping pan positions halfway

through cooking.

The “Clock button” and the

digits on the display flash.

An automatic mode has been

selected. “Hot” appears on the

display and cooking does not

start.

Troubleshooting

Установка

! Важно сохранить данное руководство для его

последующих консультации. В случае продажи,

передачи изделия или при переезде на новое место

жительства необходимо проверить, чтобы руководство

оставалось вместе с изделием, для того чтобы его новыи

владелец мог ознакомиться с правилами эксплуатации

и с соответствующими предупреждениями.

! Внимательно прочитаите инструкции: в них содержатся

важные сведения об установке, эксплуатации и

безопасности изделия.

Расположение

! Не разрешаите детям играть с упаковочными

материалами. Упаковочные материалы должны быть

уничтожены в соответствии с правилами раздельного

сбора мусора (см. Предосторожности и рекомендации).

! Монтаж изделия производится в соответствии

с данными инструкциями квалифицированными

специалистами. Неправильныи монтаж изделия может

стать причинои повреждения имущества и причинить

ущерб людям и домашним животным.

Встроенный монтаж

Для обеспечения исправного функционирования

встраиваемого изделия кухонный элемент должен иметь

соответствующие характеристики:

• панели кухонных элементов, прилегающих к духовому

шкафу, должны быть выполнены из термостойкого

материала;

• клей кухонных элементов элементов, шпонированных

деревом, должен быть устойчивым к температуре

100°C.

• для встраивания духового шкафа под кухонным

топом (см. схему) или в пенал ниша кухонного

элемента должна иметь следующие размеры:

590 mm.

595 mm.

22,5 mm.*

20,5 mm.

550 mm.

570 mm.

20 mm.

575-585 mm.

45 mm.

560 mm.

550 mm.

min.

* Только для моделей из нержавеющей стали

! После встраивания изделия в кухонный элемент

должна быть исключена возможность касания к

электрическими частями.

Расход электроэнергии, указанный на паспортной

табличке изделия, был замерян для данного типа

монтажа.

Вентиляция

Для обеспечения надлежащеи вентиляции необходимо

снять заднюю панель ниши кухонного элемента.

Рекомендуется установить духовои шкаф на два

деревянных бруска или на сплошное основание с

отверстием диаметром не менее 45 х 560 мм (см чертежи).

560 mm.

45 mm.

Центровка и крепление

Для крепления изделия к кухонному элементу:

• откройте дверцу духовки;

• снять боковые уплотнения в верхней части,

освобождая 2 крепежных отверстия;

• прикрепите духовой шкаф к нише 2 шурупами для

дерева;

• установить на место 2 уплотнения.

! Все защитные элементы должны быть закреплены

таким образом, чтобы их можно было снять только при

помощи специального инструмента.

Электрическое подключение

Духовые шкафы, укомплектованные трехполюсным

сетевым кабелем, расчитаны на функционирование

с переменным током с напряжением и частотой

электропитания, указанными на паспортной табличке с

данными (см. ниже).

Подсоединение сетевого кабеля

1. Откройте зажимную

коробку, нажав при помощи

отвертки на выступы с

боков крышки: потяните

и откройте крышку (см.

схему).

2. Порядок подсоединения

сетевого кабеля: отвинтите

винт кабельного сальника

и три винта контактов L-N-

и затем прикрепите

провода под головками

винтов, соблюдая цветовую

маркировку Синий (N)

Коричневый (L) Желто-

зеленый (см. схему).

3. Закрепите сетевой

кабель в специальном

кабельном сальнике.

4. Закройте крышку

зажимной коробки.

Подсоединение сетевого шнура изделия к сети

электропитания

Установите на сетевой кабель нормализованную

штепсельную вилку, расчитанную на нагрузку, указанную

на паспортной табличке (см. сбоку).

В случае прямого подключения к сети электропитания

между изделием и сетью необходимо установить

многополюсный выключатель с минимальным

расстоянием между контактами 3 мм, расчитанный

на данную нагрузку и соответствующий действующим

нормативам (выключатель не должен размыкать провод

заземления). Сетевой кабель должен быть расположен

таким образом, чтобы ни в одной точке его температура

не превышала температуру помещения более чем на

50°C (например, задняя панель духового шкафа).

! Электромонтер несет ответственность за правильное

подключение изделия к электрическои сети и за

соблюдение правил безопасности.

Перед подключением изделия к сети электропитания

проверьте следующее:

• розетка должна быть соединена с заземлением и

соответствовать нормативам;

• сетевая розетка должна быть рассчитана на

максимальную потребляемую мощность изделия,

указанную в таблице технических характеристик;

• напряжение и частота тока сети должны

соответствовать электрическим данным изделия;

• сетевая розетка должна быть совместима со штепсельнои

вилкои изделия. В противном случае замените розетку

или вилку; не используите удлинители или троиники.

! Изделие должно быть установлено таким образом,

чтобы электрическии провод и сетевая розетка были

легко доступны.

! Электрическии провод изделия не должен быть согнут

или сжат.

! Регулярно проверяите состояние кабеля

электропитания и в случае необходимости поручите

его замену только уполномоченным техникам (см.

Техническое обслуживание).

! Производитель не несет ответственности за

последствия несоблюдения перечисленных выше

требовании.

* Только для моделей с направляющими, изготовленными методом вытяжки.

** Только для моделей с направляющими из прутка.

ПАСПОРТНАЯ ТАБЛИЧКА

Габаритные

размеры*

ширина 43,5 см.

высота 32,4 см.

глубина 41,5 см.

Объем*

59 л

Электрическое

подключение

напряжение 220-240 В ~ 50/60 Гц

или

50 Гц

(см. Паспортную табличку),

максимальная поглощаемая

мощность 2800 Вт

ENERGY

LABEL

Директива 2002/40/СЕ об этикетках

электрических духовых шкафов.

Норматив EN 50304

Заявление о расходе электроэнергии

класса принудительной

конвекции - режим нагрева:

ECO.

Данное изделие соответствует

следующим Директивам

Европейского Сообщества:

2006/95/CEE от 12.12.06 (Низкое

напряжение) с последующими

изменениями – 2004/108/СЕЕ от

15.12.2004 (Электромагнитная

совместимость) с последующими

изменениями – 93/68/СЕЕ от 22/07/93

с последующими изменениями.

- 2012/19/CE с последующими

изменениями.

- 1275/2008 режим

энергосбережения/выкл.

Габаритные

размеры**

ширина 45,5 см.

высота 32,4 см.

глубина 41,5 см.

Объем**

62 л

Включение и эксплуатация

ВНИМАНИЕ! Духовой

шкаф укомплектован

системой блокировки

решеток, позволяющей

вынимать их из духовки

не полностью (1).

Для полного вынимания

решеток достаточно

поднять их, как показано

на схеме, взяв их за передний край, и потянуть на себя

(2).

! При первом включении духового шкафа рекомендуем

прокалить его примерно в течение часа при

максимальной температуре с закрытой дверцей. Затем

выключите духовой шкаф, откройте дверцу и проветрите

помещение. Запах, который вы можете почувствовать,

вызван испарением веществ, использованных для

предохранения духового шкафа.

! Для упрощения настройки оставьте рукоятку в

выбранном положении: цифры на дисплее сменяются

быстрее.

! Каждая настройка автоматически сохраняется в

памяти по прошествии 10 секунд.

! Активировать сенсорные кнопки touch в перчатках нельзя.

Некоторые модели укомплектованы петельной

системой, позволяющей плавно закрыть дверцу, не

прижимая ее рукой. Для правильного использования

системы перед закрыванием дверцы:

• полностью открыть дверцу.

• избегать закрывания дверцы с силой.

! Для оптимизации приготовления в момент

активирования выбранной функции производится

настройка параметром изделия, которая может вызвать

задержку включения вентилятора и нагревательных

элементов.

Блокировка управлений

! Управления можно заблокировать при выключенной

духовке, после начала или по завершении приготовленя

и в процессе программирования.

Для блокировки дверцы и управлений духовки нажмите

кнопку примерно на 2 секунды. Раздается звуковой

сигнал, на дисплее появляется символ ключа “n—O”.

Включенные символы и показывают, что

блокировка активирована.

Для разблокировки вновь нажмите примерно на 2

секунды кнопку .

! При чистке изделия можно случайно закрыть блокировку

дверцы (видна пружина). В этом случае открыть ее

можно, повернув блокировку дверцы вверх (см. схему).

KO OK

Настройка часов

! Настройка часов производится только при выключенной

духовке. Если духовка в режиме энергосбережения, при

первом нажатии кнопки показывается текущее время.

Вновь нажмите эту кнопку для настройки времени.

После подключения к электросети или после отключения

энергоснабжения кнопка и цифры на дисплее

мигают в течение 10 секунд.

Настройка часов:

1. Нажмите кнопку .

2. поверните регулятор НАСТРОЙКА ВРЕМЕНИ в

сторону “ ” и “ ” для настройки часов;

3. Выставив точное время, вновь нажмите кнопку .

4. повторить вышеописанную операцию для выставления

минут.

В случае прерывания энергоснабжения необходимо

вновь выставить время. Символ , мигающий на

дисплее, показывает, что часы настроены неправильно.

Настройка таймера

! Настроить таймер можно как при включенном, так и

при выключенном духовом шкафу. Таймер не управляет

включением или выключением духового шкафа.

По истечении заданного времени таймер включает

звуковой сигнал, который прерывается через 30 секунд

или после нажатия на любую активированную кнопку.

Порядок настройки таймера:

1. Нажмите кнопку .

2. Выставите нужное время, повернув рукоятку

НАСТРОЙКИ ВРЕМЕНИ в сторону “ ” и “ ”.

3. Выставив нужное время, вновь нажмите кнопку .

Включенный символ показывает, что таймер

включен. На ДИСПЛЕЕ показывается обратный отсчет.

Для отмены функции таймера нажмите кнопку и при

помощи рукоятки установите время на 00:00.

Вновь нажмите кнопку .

Выключение символа означает отключение таймера.

Порядок включения духового шкафа

1. Включите консоль управления при помощи кнопки

. Изделие издает три звуковых сигнала возрастающей

громкости, и последовательно загораются все кнопки.

2. Выберите нужную программу приготовления

при помощи рукоятки ПРОГРАММЫ. На дисплее

показывается:

Страница загружается ...

Indesit 7OFK 899E PX RU/HA Руководство пользователя

Бренд: Indesit

Модель: 7OFK 899E PX RU/HA

Категория: Печи

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

на других языках

English: Indesit 7OFK 899E PX RU/HA User guide

Indesit 7OFK 899E PX RU/HA Руководство пользователя

Indesit 7OFK 899E PX RU/HA Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов