Sigma BC 14.12 Alti Руководство пользователя

BIKE COMPUTER TOPLINE

VIdEO

TUTORIal:

InsTallaTIOn

VIdEO:

FUNCTIONS

SI GBBGRUSEDKFINO SK

BC 14.12 A LTI / BC 14.12

A LTI

2

Contents

1. Introduction to the BC 14.12 ALTI /

BC 14.12 STS ALTI 02

1.1 Initial use 02

1.2 Navigation principle 03

1.3 Set-up 04

2. Functions / Properties 04

2.1 General 04

2.2 Special functions 06

2.3 Altitude measurement 06

2.4 STS features 07

3. Settings / Deletion 09

3.1 Settings 09

3.2 Determining the wheel size 09

3.3 Deleting the functions 09

4. Important Notes / Troubleshooting 10

4.1 Technical data 10

5. Warranty Conditions 12

GB

1. Introduction to the BC 14.12 ALTI / BC 14.12 STS ALTIENGLISH

You can find the CE declaration under:

www.sigmasport.com

1.1 Initial use

The bike computer comes in “deep sleep mode”.

To exit this mode, press and hold the MODE 1 and

SET buttons for five seconds.

On waking up, the bike computer

will be in active mode.

To access the settings,

press the SET button.

3

GB

1.2.1 Button functions 1.2.2 Assigning the functions

1.2 Navigation principle

RESET button for

– Deleting the

current values

– Scrolling backward

You can access the following

functions by pressing the

MODE 2 button:

current altitude / trip altitude /

time / temperature /

total distance / total time /

total altitude

You can access the following

functions by pressing the

MODE 1 button:

trip distance / trip time /

Ø speed / max. speed

MODE 2 button for

– Switching between

several functions

– Scrolling forward

MODE 1 button for

– Switching between

the bike functions

– Scrolling forward

SET button for

– Switching to / from

the setting mode

– Scrolling backward

4

2.1 General

– Current / average speed comparison k

If you are traveling at approximately

your average speed, nothing is

displayed. If you are traveling

quicker than your average speed,

( ) is displayed; if you are

traveling slower ( ) is displayed.

This information is displayed in

almost all functions, except the

basic settings.

– Light manager k Simultaneously press the SET and

RESET buttons to switch the light function on / off.

The display lights up by pressing any button; the

bike computer changes to the respective function

when the button is pressed again. Avoid using the

backlight unnecessarily to save the battery!

1.3 Set-up

Please see the leaflet provided for the set-up

diagrams!

1.2.3 Display layout

2. Functions / Properties

Top field:

Speed

Middle field:

Description of the functions

Bottom field:

Current value

1.2 Navigation principle

5

GB

2. Functions / Properties

– Service interval k The service interval informs

you when you have cycled a specified number of

kilometers and a bike inspection is due. This service

interval can only be enabled/disabled and pre-

configured by your specialist retailer. The device

comes with the service interval disabled.

– Battery status k The battery status of the computer

head unit is displayed shortly before the battery

runs out. “

low / computer” appears on the display.

After changing the battery, only the time needs to be

re-set.

– Memory chip k Thanks to an inbuilt memory chip,

all total values and settings are permanently stored

in the bike computer. This means that you do not

need to reconfigure any settings (except for the time)

after changing the battery.

– PC compatibility k The bike computer is

PC-compatible. After purchasing the SIGMA

DATA CENTER software and docking station,

you can simply and effortlessly log your total

and current values on your PC. You can also

configure your bike computer’s settings on

the PC.

www.sigma-data-center.com

6

2.3 Altitude measurement

The altitude measurement on the BC 14.12 ALTI /

BC 14.12 STS ALTI is determined on the basis of the

barometric air pressure. Any change to the weather

means a change to the air pressure, which can lead

to a change to your current altitude. To compensate

these changes in air pressure, you must enter a

reference altitude into the BC 14.12 ALTI /

BC 14.12 STS ALTI (process known as calibration).

– Calibration using the start altitude k The start

altitude is the altitude of your usual start location

(generally your home). You can find this information

on road or country maps. It is set in the

BC 14.12 ALTI / BC 14.12 STS ALTI once and

calibrated within a matter of seconds.

2.2 Special functions

– Hiding total values during the trip k

If the BC 14.12 ALTI / BC 14.12 STS ALTI receives

speed signals, all the total functions (distance, time,

and cumulated altitude) are hidden on the display.

If no speed values are received, the functions

are once again displayed.

2. Functions / Properties

7

GB

2. Functions / Properties

– Calibration using the current altitude k The current

altitude is the altitude of the place at which you are

currently located irrespective of your start altitude

(your trip start location, a mountain hut, or other

locations). The current altitude is used if you are

out on your bike and altitude information is provided.

2.4 STS features

– Synchronization k Attach the BC 14.12 STS ALTI

to the bracket – zeros flash for the speed.

There are two ways of synchronizing the speed:

– 1. k Start cycling – the receiver usually

synchronizes with the transmitter after 3-4 wheel

rotations.

– 2. k Spin the front wheel until the speed values

stop flashing.

Removing the BC 14.12 STS ALTI from the bracket

severs the connection.

1 2

8

– Message “Too Many Signals” k Increase your

distance from other cyclists (transmitters) and

press any button. Synchronization re-starts. (If the

transmission connection is lost during your trip and

no longer functions, press and hold the MODE 1

button for more than three seconds to start manual

synchronization. “Sync. RESET” flashes on the

display)

2. Functions / Properties

– Transport mode k When transported on a bike

rack or in the car (if clicked into the bracket),

the BC 14.12 STS ALTI switches to “transport

mode” via an integrated movement sensor.

“Transport” appears on the display.

Press any button to exit this mode.

> 3 sec.

9

GB

3.3 Deleting the functions

Please see the diagrams for how to delete the

functions.

3. Settings / Deletion

3.1 Settings

The following settings can be configured: language /

unit / current altitude / start altitude / wheel size / time /

total distance / total time / total altitude / contrast.

Clear diagrams of how to set each of these functions

can be found in the enclosed leaflet.

3.2 Determining the wheel size

To measure your speed precisely, the wheel size must

be set on the basis of your tire size. To do this, you can:

A – Calculate the wheel size using the formula provided

in the wheel size chart.

B – Determine the value from the drawings in the

wheel size chart.

C – Take the value that corresponds to your tire size

from the wheel size chart.

10

4.1 Technical data

4.1.1 Battery indicator / replacement

Please see the enclosed diagrams for how to insert or

remove the battery. After changing the battery in the

computer head unit, only the time needs to be re-set.

BC 14.12 ALTI Type CR 2032 /

computer head unit: 1.5-year service life*

BC 14.12 STS ALTI Type CR 2032 /

computer head unit: 1-year service life*

Speed transmitter: Type CR 2032 /

1-year service life*

* when used for one hour per day

4. Important Notes / Troubleshooting

4.1.2 Troubleshooting

No speed:

– Is the computer correctly fastened into the bracket?

– Check the distance between the magnet and the

sensor (max. 12 mm).

– Is the magnet correctly positioned?

Incorrect speed:

– Are two magnets attached to the bike?

– Is the wheel size correctly set?

Further troubleshooting solutions can be found in our

FAQs at www.sigmasport.com

11

GB

4.1.3 Min. / max. / factory settings

Standard Min. Max. Unit

Current speed 0.0 0 199.8 kmh / mph

Trip Dist 0.00 0.00 9,999.9 km / mi

Ride Time 0:00:00 0:00:00 999:59:59 h:mm:ss hhh:mm:ss

Avg Speed 0.00 0.00 199.8 kmh / mph

Max. Speed 0.00 0.00 199.8 kmh / mph

Act Altitude 0 -999 4,999 / 16,999 m / ft

Altitude Up 0 0 99,999 m / ft

Max Altitude 0 -999 4,999 / 16,999 m / ft

Clock 00:00 00:00 23:59 hh:mm

Temperature 0.0 -10 / 14 70 / 158 °C / °F

Tot Distance 0 0 99,999 km / mi

Total Time 0:00 0:00 19,999 h:mm hh.hhh

Tot. Alti. 0 0 99,999 m / ft

Wheelsize 2,155 500 3,999 mm

4. Important Notes / Troubleshooting

12

We are liable to our contracting partners for defects

in line with legal provisions. In the event of a warranty

claim, please contact the retailer from whom you

purchased your bike computer. You can also send

your bike computer, together with your receipt and all

accessories, to the address below. Please ensure you

pay sufficient postage.

Warranty claims can be made in the event of material

and workmanship errors. The warranty does not cover

batteries, wear and tear parts, or wear caused by

commercial use or accidents. Warranty claims shall

only be valid if the SIGMA product has not been opened

without authorization and the purchase receipt is

provided.

SIGMA-ELEKTRO GmbH hereby declares that the

wireless bike computers comply with the fundamental

requirements and other relevant regulations of

Directive 1999/5/EC.

5. Warranty Conditions

SIGMA-ELEKTRO GmbH

Dr.-Julius-Leber-Strasse 15

D-67433 Neustadt an der Weinstrasse

Tel.: +49 (0) 63 21- 91 20 -118

Fax.: +49 (0) 63 21- 91 20 -34

E-mail: [email protected]

In the event of justified warranty claims, you will

receive a replacement device. You will only be entitled

to the model available at the time of replacement.

The manufacturer retains the right to make technical

modifications.

Batteries must not be disposed of in household waste

(European Battery Law)! Please take the batteries to

an official collection point for disposal.

Electronic devices must not be

disposed of in household waste.

Please take the device to an

official waste collection point.

LI=Lithium

LI

13

GB

Notes

14

Kazalo

1. Spoznajte BC 14.12 ALTI / BC 14.12 STS ALTI 14

1.1 Zagon 14

1.2 Princip navigacije 15

1.3 Montaža 16

2. Funkcije / lastnosti 16

2.1 Splošno 16

2.2 Posebne funkcije 18

2.3 Merjenje višine 18

2.4 Posebnosti STS 19

3. Nastavitve / brisanje 21

3.1 Nastavitve 21

3.2 Ugotavljanje obsega kolesa 21

3.3 Brisanje funkcij 21

4. Pomembna opozorila / odprava napak 22

4.1 Tehnični podatki 22

5. Garancijska določila 24

SI

1. Spoznajte BC 14.12 ALTI / BC 14.12 STS ALTISLOVENŠČINA

Izjavo CE najdete na www.sigmasport.com

1.1 Zagon

Ob dobavi je kolesarski računalnik v tako imenovanem

načinu globokega mirovanja.

Da zapustite ta način, pritisnite

tipko MODE 1 in tipko SET in

ju zadržite 5 sekund.

Ko se kolesarski računalnik zbudi,

je v aktivnem načinu.

V nastavitve se pomaknete

s pritiskom na tipko SET.

15

SI

1.2.1 Pomen tipk 1.2.2 Dodelitev funkcij

1.2 Princip navigacije

Tipka RESET za

– brisanje trenutnih

vrednosti

– listanje nazaj

S tipko MODE 2 lahko prikličete

naslednje funkcije:

Tren. višina / Dnevna višina / Ura /

Temperatura / Skupna pot /

Skupni čas / Skupna višina

S tipko MODE 1 lahko prikličete

naslednje funkcije:

Prevožena pot / Čas vožnje /

Ø hitrost / Maks. hitrost

Tipka MODE 2 za

– menjavo raznih

funkcij

– listanje naprej

Tipka MODE 1 za

– menjavo kolesarskih

funkcij

– listanje naprej

Tipka SET za

– menjavo v / iz

nastavitvenega načina

– listanje nazaj

16

2.1 Splošno

– Primerjava trenutne / povprečne hitrosti k

Če vozite s hitrostjo, ki je

približno enaka povprečni,

se ne prikazuje nič. Če vozite

s hitrostjo, višjo od povprečne,

se prikazuje ( ), če pa s

hitrostjo, nižjo od povprečne,

pa ( ). Prikaz je aktiven pri

vseh funkcijah, razen pri osnovnih

nastavitvah.

– Upravljanje svetlobe k Z istočasnim pritiskom na

tipki SET in RESET lahko vklopite / izklopite osvetlitev

zaslona. S pritiskom na poljubno tipko se vklopi

osvetlitev zaslona, z naslednjim pritiskom na

določeno tipko pa se vklopi naslednja funkcija

kolesarskega računalnika. Ne vklapljajte osvetlitve

po nepotrebnem, da se baterija ne izprazni prehitro!

1.3 Montaža

Slike za montažo so razvidne iz priložene zgibanke!

1.2.3 Zgradba zaslona

2. Funkcije / lastnosti

Zgornje segmentno polje:

prikaz hitrosti

Srednje segmentno polje:

opis funkcij

Spodnje segmentno polje:

trenutna vrednost

1.2 Princip navigacije

17

SI

2. Funkcije / lastnosti

– Servisni interval k Servisni interval vas obvesti,

ko dosežete kilometrino za naslednji pregled kolesa.

Servisni interval se lahko vklopi / izklopi oz. pred-

programira samo v pooblaščeni trgovini. Ob dobavi

je servisni interval izklopljen.

– Stanje baterije k Stanje baterije računalniškega dela

se prikaže, tik preden je baterija prazna. Prikaže se:

„

prazna / računalnik“ na zaslonu. Po menjavi

baterije je treba na novo programirati le uro.

– Pomnilniški čip k S pomočjo vgrajenega

pomnilniškega čipa se skupne in nastavljene vrednosti

v kolesarskem računalniku trajno shranijo. Zato vam

po menjavi baterije ni treba opraviti nastavitev

(razen ure).

– Kompatibilnost z osebnim računalnikom k

Kolesarski računalnik lahko priključite na osebni

računalnik. Če kupite programsko opremo SIGMA

DATA CENTER in priklopno postajo, lahko skupne in

dnevne vrednosti enostavno in hitro shranite na

osebni računalnik. Poleg tega lahko na osebnem

računalniku opravite tudi nastavitve kolesarskega

računalnika.

www.sigma-data-center.com

18

2.3 Merjenje višine

BC 14.12 ALTI / BC 14.12 STS ALTI višino meri na

podlagi preračuna barometričnega zračnega tlaka.

Vsaka sprememba vremena pomeni spremembo

zračnega tlaka, kar lahko povzroči spremembo

trenutne višine. Da bi to spremembo zračnega tlaka

kompenzirali, je treba v BC 14.12 ALTI /

BC 14.12 STS ALTI I vnesti referenčno višino

(tako imenovano kalibriranje).

– Kalibriranje s startno višino k Startna višina je

višina kraja, kjer se običajno nahajate (praviloma

je to vaše bivališče). To vrednost lahko preberete

z avtomobilskih kart oz. zemljevidov. Vrednost enkrat

nastavite v BC 14.12 ALTI / BC 14.12 STS ALTI,

kalibrira pa se v roku nekaj sekund.

2.2 Posebne funkcije

– Izklop prikaza skupnih vrednosti med vožnjo k

Ko BC 14.12 ALTI / BC 14.12 STS ALTI sprejema

signale hitrosti, so vse skupne funkcije (pot, čas in

kumulirana višina) nevidne. Ko ni več sprejema

vrednosti hitrosti, se funkcije spet pojavijo na

prikazu.

2. Funkcije / lastnosti

19

SI

2. Funkcije / lastnosti

– Kalibriranje s trenutno višino k Trenutna višina

je višina kraja, na katerem se trenutno nahajate,

neodvisno od vaše startne višine (vašega

izhodiščnega kraja ture, planinske koče ali drugih

krajev). Trenutna višina se uporablja, če ste na

poti s kolesom in imate na voljo podatek o višini.

2.4 Posebnosti STS

– Sinhronizacija k BC 14.12 STS ALTI vstavite

v držalo – Ničle prikaza hitrosti utripajo.

Hitrost lahko sinhronizirate na dva načina:

– 1. k Speljite in sprejemnik se praviloma po

3-4 obratih kolesa sinhronizira z oddajnikom.

– 2. k Obračajte sprednje kolo tako dolgo, da prikaz

hitrosti preneha utripati.

Če BC 14.12 STS ALTI odstranite iz držala,

se povezava prekine.

1 2

20

– Prikaz „preveč signalov“ k Povečajte razdaljo do

drugih voznikov (oddajnikov) in pritisnite poljubno

tipko. Sinhronizacija se bo na novo zagnala. (Če pride

med vožnjo do izpada prenosa in prenosa ni več,

pritisnite tipko MODE 1 za dlje kot 3 sek., da

zaženete ročno sinhronizacijo. Na zaslonu utripa

„Sync. RESET“.)

2. Funkcije / lastnosti

– Transportni način k V primeru prevoza kolesa

na nosilcu ali v avtomobilu (če ga pričvrstite na

nosilec) se računalnik BC 14.12 STS ALTI z

vgrajenim senzorjem premikanja preklopi na

transportni način. Na zaslonu se prikaže „Transport“.

Če želite zapustiti ta način, morate na kratko

pritisniti poljubno tipko.

> 3 sek.

Страница загружается ...

Sigma BC 14.12 Alti Руководство пользователя

Это руководство также подходит для

Sigma BC 14.12 Alti Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов